Guardian Protective Coatings Pty Ltd
Email:gary@guardit.net
A.C.N. 061 748 543
PRODUCT INFORMATION SHEET
PRODUCT:
GUARDIAN GRAFFITI SHIELD
Product Code: GGSPI
Issue Date: JANUARY 2015
Page 1 of 3
Description
Environmently friendly, water based anti graffiti impregnation with a sacrificial layer which will remain effective if
not removed for up to 10 years, when correctly applied to properly prepared surfaces.
Guardian Graffiti Shield is a milky, fast and transparent drying, aqueous impregnation for absorbent, cementitious facade
surfaces. An anti graffiti effect results after the application has dried. The surface structure of the surface to be treated
remains as it is. Its colour deepens and any glossiness will be slightly reduced.
Graffiti from spray paints can be cleaned with hot steam approx. 80C - 90C in a spray procedure or from non porous
surfaces with Guardian Graffiti Remover or Guardian Graffiti Gel. A part of the impregnation dissolves (sacrificial layer)
off the surface and must be reapplied after cleaning.
Guardian Graffiti Shield also reduces the absorption of water and pollutants. After application, Guardian Graffiti Shield
covers capillary and pore walls with a macromolecular layer, reducing water vapour diffusion capacity.
Uses
Guardian Graffiti Shield can be used for treating absorbent, cementitious building materials on wall areas, as well as in
certain cases non absorbent substrates. Suitability and compatability should be assessed.
Product characteristics data in the packaged state:
Active ingredient base:
Solid content:
Carrier agent:
Density:
Viscosity:
Appearance:
Shelf Life:
Packaging:
special silicone compound
13.5%
water
1.0kg/lt
DIN 4 flow cup 12 sec
milky turbid
at least ½ year in closed containers
1lt, 5lt and 30lt plastic canisters
Product characteristics data after application and active ingredient formation:
Water absorption:
UV light stability:
Weathering resistance:
Long term effect:
Alkali resistance:
Non stick drying:
Soiling tendency:
Prodinfo.doc
very little
very good
good
high
up to pH 14
yes, if applied properly
little
Guardian Protective Coatings Pty Ltd
Email:gary@guardit.net
A.C.N. 061 748 543
PRODUCT INFORMATION SHEET
PRODUCT:
GUARDIAN GRAFFITI SHIELD
Product Code: GGSPI
Issue Date: JANUARY 2015
Page 2 of 3
Working Instructions:
Surface Pretreatment:
The substrate must be in sound condition. Constructional defects such as, eg. Cracks, cracked joints, faulty connections,
rising and hygroscopic moisture must be corrected first. It must be ensured that water and damaging salts dissolved in the
water cannot penetrate behind the treated area. Before any hydrophobising impregnation is carried out, crusts from soiling
and pollutants, as well as efflorescence, alga and moss must be removed by a suitable cleaning method. Cleaning opens
capillaries and pores so that the impregnation agent can be absorbed.
When cleaning, be careful not to damage building substance any more than necessary. Cleaner residue (eg. wetting agents)
from prior cleaning may impair the reduction of water absorbency on the treated surfaces and should therefore be
thoroughly washed off.
Surface condition:
If building damaging salts are present, a quantitative analysis is essential. High concentrations of damaging salts
(especially chlorides and nitrates) lead to constructional damage that cannot be prevented by a hydrophobic impregnation.
Adjoining surfaces:
Those parts of the surface that are not to be impregnated such as, eg. windows, varnished surfaces or surfaces to be
varnished and glass, as well as plants should be covered with (polyethylene) sheeting.
Application procedure:
The impregnation agent is applied in a pressureless flow coating procedure generously enough that a 30-50cm long film of
liquid runs down the building material surfaces. The spray jet should be held horizontally and lead continuously along the
facade. After absorption of the impregnation agent, the process is to be repeated at least once. Adjust spraying pressure
and jet diameter so that misting does not occur.
To avoid missing places, limited sections should be completely impregnated at one time, without interruption. For smaller,
complicated surfaces that do not allow a spray or flow coat application, use a brush or roller. With this method,
insufficient application amounts can only be avoided by using well saturated tools. The freshly treated surface must be
protected against driving rain for at least 5 hours. Strong wind and direct sunlight can also accelerate evaporation of the
carrier agent which negatively influences penetration depth.
Working temperature:
Treatment of surfaces can be carried out at an object temperature ranging between 10C to 25C.
Tools:
All low pressure, conveyor and spray equipment and liquid pumps - are suitable. The equipment must be clean and dry.
After use and before longer work pauses, clean thoroughly with water.
Prodinfo.doc
Guardian Protective Coatings Pty Ltd
Email:gary@guardit.net
A.C.N. 061 748 543
PRODUCT INFORMATION SHEET
PRODUCT:
GUARDIAN GRAFFITI SHIELD
Product Code: GGSPI
Issue Date: JANUARY 2015
Page 3 of 3
Amount required:
Sand-lime brick:
Natural stone:
Brick:
Granite
0.02 - 0.04 lt/m2
0.40 - 0.80 lt/m2
0.10 - 0.30 lt/m2
0.05 - 0.20 1/m2
Exact amounts for calculation and tender must be determined on a sufficiently large trial area (1-2 m2). The effectiveness
of the impregnation can also be tested on this surface.
Disposal:
Product remains must be disposed of in an incinerator for special refuse. Empty containers should be disposed of in
compliance with official regulations. Do not lead into waste water drains.
Specification Sheets:
Refer to corresponding Material Safety Data Sheets GGSMSDS.
The statements above are compiled from our field of production and according to the latest technological developments and application techniques.
Since application and working are beyond our control, no liability of the producer can be derived from the contents of this information sheet.
Guardian Protective Coatings Pty Ltd and associated group of companies shall not be responsible for any damage or injury resulting from abnormal
use of the material, from any failure to adhere or observe the recommendations, or from any hazards inherent in the nature of the material. It is the
users responsibility to evaluate the information contained herein and use this product safely and within the current laws and regulations.
Prodinfo.doc
Guardian Protective Coatings Pty Ltd
Email:gary@guardit.net
A.C.N. 061 748 543
MATERIAL SAFETY DATA SHEET
PRODUCT:
GUARDIAN GRAFFITI SHIELD
Product code:
GGSMSDS
Issue Date: JANUARY 2015
Page No: 1 of 3
Worksafe Hazard Assessment: Non Hazardous According To Criteria Of Worksafe Australia
Company details:
Guardian Protective Coatings Pty Ltd
2/44 Barnfield Rd
Claremont, Western Australia 6010
TEL:+61 (0)408882906 FAX:+61 8 92846660
UN: None allocated.
CLASS: None allocated
SUB RISK: None allocated
HAZ CHEM CODE: None allocated
EPG: None allocated
PACKAGING GROUP: None allocated
POISON SCHEDULE: Not scheduled
USES: Aqueous antigraffiti protection impregnation for masonry surfaces.
PHYSICAL AND CHEMICAL PROPERTIES
APPEARANCE: Milky liquid.
BOILING POINT: 100C
VAPOUR PRESSURE: Not determined.
SPECIFIC GRAVITY: 1.00 Kg/lt @ 20C
FLASH POINT: Not applicable
% VOLATILES: No data available
MELTING POINT: Not determined
VAPOUR DENSITY: Not determined
SOLUBILITY (WATER): Fully miscible
EXPLOSION LIMITS: Not selfigniting
pH: 8.9 @ 20C
INGREDIENTS
Chemical Name
Triethoxyoctylsilane
CAS Number
2943-75-1
Proportion
 2.5%
TOXICOLOGICAL INFORMATION
INGESTION:
Ingestion may cause irritation to the stomach, nausea and vomiting. If vomiting occurs after ingestion, small droplets of
the liquid may enter the lungs (aspiration) with the risk of chemical pneumonia being induced.
EYE:
No irritant effect.
SKIN
No irritant effect.
INHALATION:
No irritant effect.
msds.doc
Guardian Protective Coatings Pty Ltd
Email:gary@guardit.net
A.C.N. 061 748 543
MATERIAL SAFETY DATA SHEET
PRODUCT:
GUARDIAN GRAFFITI SHIELD
Product code:
GGSMSDS
Issue Date: JANUARY 2015
Page No: 2 of 3
CHRONIC
No information available at present. When used and handled according to specifications, the product does not have any
harmful effects according to our experience and the information provided to us.
FIRST AID PROCEDURES
INGESTION
NEVER GIVE AN UNCONSCIOUS PERSON ANYTHING TO DRINK NOR ATTEMPT TO INDUCE VOMITING.
If person is conscious, rinse mouth out with water ensuring that mouth wash is not swallowed. Give about 250ml (2
glasses) of water to drink. DO NOT attempt to induce vomiting. Seek medical attention.
EYE
Hold eyelids open and rinse the eye continuously with a gentle stream of clean running water for at least fifteen minutes.
Seek medical attention.
SKIN
Remove contaminated clothing and wash thoroughly with soap and water. Use water alone, if soap is unavailable. Apply
a moisturising hand cream, if available. Seek medical attention if any soreness or inflammation of the skin persists or
develops later. Launder affected clothing before re-use.
INHALATION
Remove to fresh air. Keep warm and at rest. If breathing is laboured, hold in a half upright position (this assists
respiration). Apply artificial respiration if breathing has stopped. Seek medical attention.
PRECAUTIONS OF USE
ENGINEERING CONTROL
There are no special requirements for use outdoors or in well ventilated areas. If the product is used in poorly ventilated
areas then fan forced air ventilation may be required.
PERSONAL PROTECTION
Safety glasses with side shields or safety goggles, protective gloves and protective skin cream. Respiratory protection is
unlikely to be required for normal use but if inhalation risk exists then a half face respirator meeting the requirements of
AS/NZS 1715 and AS/NZS 1716 is suitable for use.
N.B. TAKE THE LIMITS OF ABSORPTION CAPACITY INTO ACCOUNT. CHANGE FILTERS REGULARLY.
AIR PURIFYING RESPIRATORS DO NOT PROTECT AGAINST OXYGEN DEFICIENT ATMOSPHERES.
msds.do
Guardian Protective Coatings Pty Ltd
Email:gary@guardit.net
A.C.N. 061 748 543
MATERIAL SAFETY DATA SHEET
PRODUCT:
GUARDIAN GRAFFITI SHIELD
Product code:
GGSMSDS
Issue Date JANUARY 2015
Page No: 3 of 3
FLAMMABILITY
Not flammable, product is not selfigniting.
EXPOSURE STANDARD
No exposure standards have been established for this product or its components.
SAFE HANDLING PROCEDURES
STORAGE
Store out of direct sunlight under dry conditions. Do not store under 5C. Protect containers against physical damage.
TRANSPORT
Not dangerous according to the following specifications
LAND:
ADR/RID and GGCVS/GGVE
ADR/RID-GGVS/E Class
SEA: IMDG/GGVSea
IMDG/GGVSea Class
AIR: ICAO-TI and IATA-DGR
ICAO/IATA Class
PACK SIZE
5ll & 10lt Plastic Containers
.
SPILLS, DISPOSAL, CLEAN UP
SPILLS: Take up smallest amounts with liquid binding material (sand, sawdust, diatomaceous earth) and dispose of as
building rubble or household garbage.
DISPOSAL: If possible, return to supplier. Otherwise, dispose according to official regulations. Do not lead into waste
water drains.
CLEAN UP: Water, if necessary with cleaning agent.
FIRE EXPLOSION
Suitable extinguishing agents. Use fire fighting measures that suit the environment.
CONTACT POINT
Emergency Advice
Issue Date:
Supersedes issue date:
Reasons for issue:
January 2015
January 2004
Company details.
APPROVED BY:
13 11 26
Poisons Information Center
Gary Dwyer
This data sheet and the health and safety hazard information it contains is considered to be accurate as at the date of issue. However, no warranty or
recommendation, express or implied, is made as to the accuracy or completeness of the data and information contained within. Each user should
read this data sheet and consider the information in the context of how the product will be handled and used. Health and safety precautions
mentioned in this data sheet may not be accurate for all individuals and/or situations. Guardian Protective Coatings and associated group of
companies shall not be responsible for any damage or injury resulting from abnormal use of the material, from any failure to adhere or observe the
recommendations, or from any hazards inherent in the nature of the material. It is the users responsibility to evaluate the information contained
herein and use this product safely and within the current laws and regulations.
msds..doc