_____[ 1 ]___[ 11:52:39,465 ]___[ DOWN ]____[ BCCH ]______________________________
06 1b cd 3a 62 f2 10 31 04 40 04 3c 55 65 08 a5 00 00 3c 2b 2b 2b
06
0-------000-------0110
direction from
TransactionID
Protocol Discrim.
: originating site
: 0
: radio resource management messages
1b
00011011
MESSAGE TYPE
: SYSTEM INFORMATION TYPE 3
: Cell Identity
cd 11001101 Cell identity value1: Hex-Wert verwenden
3a 00111010 Cell identity value2: Hex-Wert verwenden
: Location Area Identification
62 ----0010 Mobile CC digit 1
0110---- Mobile CC digit 2
f2 ----0010 Mobile CC digit 3
: 2
: 6
: 2
10
1111-------0000
0001----
Mobile NC digit 3
Mobile NC digit 1
Mobile NC digit 2
: 15
: 0
: 1
31
04
00110001
00000100
Loc. area code (LAC) = ID of MSC (hex)
Loc. area code (LAC) = ID of BSC (hex)
: Control Channel Description
40 0------- 1 spare bit
: 0
-1------ MSs in the cell shall apply IMSI attach and detach procedure
--000--- Number of blocks
: 0 reserved for access grant
-----000 1 basic physical channel used for CCCH not combined with SDCCHs
04
00000--- spare bits
: 5
-----100 6 multi frames period for transmission PAGING REQUEST messages to the
same paging subgroup
3c
00111100
T3212 TimeOut value : 60 deci hours
: Cell Options BCCH,
55 0------- 1 spare bit
: 0
-1------ PWRC Power control indicator is set
--01---- MSs shall use uplink discontinous transmission
----0101 Radio Link Timeout : 24
: Cell Selection Parameters;
65 011----- Cell Resel. Hyster. : 6 dB RXLEV hysteresis for level average (LA) reselection
---00101 Max Tx power level : Mobile may use 5
08 0------- Addition. Reselect Param ind: in SI4 rest octets, i.p., and SI7 and SI8
rest octets, ...
-0------ New establishment cause is not supported
--001000 RXLEV ACCESS MIN
: -110 +8 db permitted
: RACH Control Parameters
a5 10------ Max. of retransm.
: 4
--1001-- used to spread TX
: 12 slots
------0- The cell is barred : no
-------1 Call reestablishment in cell is not allowed
00
-----0-00000--------00
Emergency Call EC10 : allowed
Acc.contr.cl. 11-15 : 0/1 access permitted/forbidden
Acc.contr.cl.
8-9 : 0/1 access permitted/forbidden
00
00000000
Acc.contr.cl.
0-7 : 0/1 access permitted/forbidden
: SI 3 Restoktett
0 Selection Parameters not present
0 Power Offset not present
1 System Information 2ter Indicator not present
1 Early Classmark Sending Control present
1 Scheduling if and where not present
1 High: GPRS indicator = present
: RA COLOUR
000 Routing Area colour = 0
: SI13 Position
0 SYSTEM INFORMATION TYPE 13 message is sent on BCCH Norm;
10101100 spare bits
: End SI 3 Restoktett
_____[ 2 ]___[ 11:52:39,684 ]___[ DOWN ]____[ BCCH ]______________________________
06 1c 62 f2 10 31 04 65 08 a5 00 00 01 2b 2b 2b 2b 2b 2b 2b 2b 2b
06
0-------000-------0110
direction from
TransactionID
Protocol Discrim.
: originating site
: 0
: radio resource management messages
1c
00011100
MESSAGE TYPE
: SYSTEM INFORMATION TYPE 4
: Location Area Identification
62 ----0010 Mobile CC digit 1
0110---- Mobile CC digit 2
f2 ----0010 Mobile CC digit 3
: 2
: 6
: 2
10
1111-------0000
0001----
Mobile NC digit 3
Mobile NC digit 1
Mobile NC digit 2
: 15
: 0
: 1
31
04
00110001
00000100
Loc. area code (LAI), ID of MSC (hex)
Loc. area code (LAI), ID of BSC (hex)
: Cell Selection Parameters
65 011----- Cell Reselect Hyst. : 6 dB RXLEV hyst. For LA re-select
---00101 Max Tx power level : MS may use 5
08
0-------0-------001000
No Additional cells in SysInfo 7-8
New establishm.cause: not supported
RXLEV ACCESS MIN permitted = -110+8dB
: RACH Control Parameters
a5 10------ Max. of retransmissions
--1001-- 12 slots used to spread TX
------0- The cell is barred : no
-------1 Call reestab.in cell: not allowed
00
-----0-00000--forbidden
------00
forbidden
00 00000000
forbidden
Emergency Call EC 10: allowed
Acc. ctrl class11-15: bit pattern,0 = access permitted, 1 = access
Acc. ctrl class 8-9 : bit pattern,0 = access permitted, 1 = access
Acc. ctrl class 0-7 : bit pattern,0 = access permitted, 1 = access
: SI4 Rest Octets
: SI4 Rest Octets_O
: Optional selection parameters
0 Selection Parameters = not present
: End Optional selection parameters
: Optional Power offset
0 Power Offset = not present
: End Optional Power offset
: GPRS Indicator
0 High: GPRS indicator = present
: RA COLOUR
000 Routing Area colour = 0
: SI13 Position
0 SYSTEM INFORMATION TYPE 13 message is sent on BCCH Norm;
: End GPRS Indicator
: End SI4 Rest Octets_O
: Break Indicator
1 High Additional parameters, "SI4 Rest Octets_S" are sent in SYSTEM
INFORMATION TYPE 7 and 8
: End SI4 Restoctet
_____[ 3 ]___[ 11:52:40,395 ]___[ DOWN ]____[ BCCH ]______________________________
06 1b cd 3a 62 f2 10 31 04 40 04 3c 55 65 08 a5 00 00 3c 2b 2b 2b
06
0-------000-------0110
direction from
TransactionID
Protocol Discrim.
: originating site
: 0
: radio resource management messages
1b
00011011
MESSAGE TYPE
: SYSTEM INFORMATION TYPE 3
: Cell Identity
cd 11001101 Cell identity value1: Hex-Wert verwenden
3a 00111010 Cell identity value2: Hex-Wert verwenden
: Location Area Identification
62 ----0010 Mobile CC digit 1
0110---- Mobile CC digit 2
f2 ----0010 Mobile CC digit 3
: 2
: 6
: 2
10
1111-------0000
0001----
Mobile NC digit 3
Mobile NC digit 1
Mobile NC digit 2
: 15
: 0
: 1
31
04
00110001
00000100
Loc. area code (LAC) = ID of MSC (hex)
Loc. area code (LAC) = ID of BSC (hex)
: Control Channel Description
40 0------- 1 spare bit
: 0
-1------ MSs in the cell shall apply IMSI attach and detach procedure
--000--- Number of blocks
: 0 reserved for access grant
-----000 1 basic physical channel used for CCCH not combined with SDCCHs
04
00000--- spare bits
: 5
-----100 6 multi frames period for transmission PAGING REQUEST messages to the
same paging subgroup
3c
00111100
T3212 TimeOut value : 60 deci hours
: Cell Options BCCH,
55 0------- 1 spare bit
: 0
-1------ PWRC Power control indicator is set
--01---- MSs shall use uplink discontinous transmission
----0101 Radio Link Timeout : 24
: Cell Selection Parameters;
65 011----- Cell Resel. Hyster. : 6 dB RXLEV hysteresis for level average (LA) reselection
---00101 Max Tx power level : Mobile may use 5
08 0------- Addition. Reselect Param ind: in SI4 rest octets, i.p., and SI7 and SI8
rest octets, ...
-0------ New establishment cause is not supported
--001000 RXLEV ACCESS MIN
: -110 +8 db permitted
: RACH Control Parameters
a5 10------ Max. of retransm.
: 4
--1001-- used to spread TX
: 12 slots
------0- The cell is barred : no
-------1 Call reestablishment in cell is not allowed
00
-----0-00000--------00
Emergency Call EC10 : allowed
Acc.contr.cl. 11-15 : 0/1 access permitted/forbidden
Acc.contr.cl.
8-9 : 0/1 access permitted/forbidden
00
00000000
Acc.contr.cl.
0-7 : 0/1 access permitted/forbidden
: SI 3 Restoktett
0 Selection Parameters not present
0 Power Offset not present
1 System Information 2ter Indicator not present
1 Early Classmark Sending Control present
1 Scheduling if and where not present
1 High: GPRS indicator = present
: RA COLOUR
000 Routing Area colour = 0
: SI13 Position
0 SYSTEM INFORMATION TYPE 13 message is sent on BCCH Norm;
10101100 spare bits
: End SI 3 Restoktett
_____[ 4 ]___[ 11:52:40,434 ]___[ DOWN ]____[ PCH ]______________________________
06 21 00 01 00 2b 2b 2b 2b 2b 2b 2b 2b 2b 2b 2b 2b 2b 2b 2b 2b 2b
06
0-------000-------0110
direction from
TransactionID
Protocol Discrim.
: originating site
: 0
: radio resource management messages
21
00100001
MESSAGE TYPE
: PAGING REQUEST TYPE 1
00
----00-------00
--00---00------
spare bits
Page Mode
Channel Needed
Channel Needed
:
:
:
:
0
Normal paging
(first) Any Channel
(second) Any Channel
: Mobile Identity 1
01 00000001 length of Mob.ident.:
00 0000---- Identity Digit 1
:
----0--- No. of ID digits
:
-----000 Type of identity
:
1
hex value = f, if
even
No Identity
TMSI/P-TMSI
_____[ 5 ]___[ 11:52:40,863 ]___[ DOWN ]____[ BCCH ]______________________________
06 19 00 00 00 20 00 00 00 00 00 00 00 10 20 00 20 00 a5 00 00 2b
06
0-------000-------0110
direction from
TransactionID
Protocol Discrim.
19
00011001
MESSAGE TYPE
: Cell Channel Description
00 00------ Format Type
--00---- 2 spare bits
: originating site
: 0
: radio resource management messages
: SYSTEM INFORMATION TYPE 1
: Bit Map 0 format
: 0
20
10
20
20
--1-------1-----1------1-----
Cell
Cell
Cell
Cell
Allocation
Allocation
Allocation
Allocation
: RACH Control Parameters
a5 10------ Max. of retransmiss
--1001-- slots to spread TX
------0- The cell is barred
-------1 Call reestabl.i.cell
:
:
:
:
ARFCN
ARFCN
ARFCN
ARFCN
102
37
30
14
:
:
:
:
4
12
no
not allowed
00
00000-------0-------00
Acc. contr. cl. 11-15: Bitmuster: 0 Zugr.erl.,1 Zugr.n.erl.
Emergency Call EC 10 : allowed
Acc. contr. cl. 8-9 : Bitmuster: 0 Zugr.erl.,1 Zugr.n.erl.
00
00000000
Acc. contr. cl. 0-7
: Bitmuster: 0 Zugr.erl.,1 Zugr.n.erl.
: NCH Position
0 no NCH Position
0101011 spare padding
_____[ 6 ]___[ 11:52:41,207 ]___[ DOWN ]____[ BCCH ]______________________________
06 1a 00 00 00 00 04 10 00 00 00 00 00 c0 a2 9d 00 00 08 a5 00 00
06
0-------000-------0110
direction from
TransactionID
Protocol Discrim.
: originating site
: 0
: radio resource management messages
1a
00011010
MESSAGHE TYPE
: SYSTEM INFORMATION TYPE 2
00
--0-------0----
Extension Indicator : The IE carries the complete BA
BCCH alloc. sequ.num: 0
04
10
c0
-----1----1---1-------1-----1--------1----------11---------1-------1-------1--------1
BCCH
BCCH
BCCH
BCCH
BCCH
BCCH
BCCH
BCCH
BCCH
BCCH
BCCH
BCCH
08
----1---
BCCH carrier with NCC = 3 is permitted for monitoring;
a5
10-------1001-------0-------1
Max. of retransmiss.: 4
12 slots used to spread TX
The cell is barred : no
Call reestablishment in cell is not allowed
00
-----0-00000--------00
Emergency Call EC 10: allowed
acc ctrl class 11-15: 0/1 access permitted/forbidden
acc ctrl class 8-9 : 0/1 access permitted/forbidden
00
00000000
acc ctrl class
a2
9d
alloc.
alloc.
alloc.
alloc.
alloc.
alloc.
alloc.
alloc.
alloc.
alloc.
alloc.
alloc.
RF
RF
RF
RF
RF
RF
RF
RF
RF
RF
RF
RF
chan.:
chan.:
chan.:
chan.:
chan.:
chan.:
chan.:
chan.:
chan.:
chan.:
chan.:
chan.:
91
85
40
39
32
30
26
24
21
20
19
17
0-7 : 0/1 access permitted/forbidden
_____[ 7 ]___[ 11:52:41,805 ]___[ DOWN ]____[ BCCH ]______________________________
06 00 b0 a0 01 f8 05 85 86 7c a1 08 05 18 03 2b 2b 2b 2b 2b 2b 2b
06
0-------000-------0110
direction from
TransactionID
Protocol Discrim.
: originating site
: 0
: radio resource management messages
00
00000000
MESSAGE TYPE
: SYSTEM INFORMATION TYPE 13
1-------011-------0000
SI 13 Restoctet
BCCH_CHANGE_MARK
SI_CHANGE_FIELD
: present
: 3
: Update of unspecified SI messages
1
01
SI13_CHANGE_MARK = present
SI13_CHANGE_MARK
: 1
: GPRS Mobile Allocation IE
000000
0
0
000011
HSN (hopping sequence number) = 0
RFL number list struckt = not present
MA_Length and Bitmap = present
BITMAP_LENGTH
: 3+1
BITMAP
: 1111
: End GPRS Mobile Allocation
0 PBCCH not present in Cell
00000001 RAC (Routing Area Code) = 1
0 SPGC_CCCH_SUP
: SPLIT_PG_CYCLE not supported on CCCH
: Priority access
110 packet access is allowed for priority level 1 to 4;
: Network Control Order
00 NETWORK_CONTR. ORDER: MS controlled cell re-selection, no measurement
reporting.
: GPRS CELL OPTIONS IE
01
011
000-------011-------0-------0
1111
1
001
010
000
NMO Network Mode of Operation II : No PPCH available, no Gs If
T3168
: (3+1)x500 ms
T3192
: 500msec
DRXTIMER_MAX
ACCESS_BURST_TYPE
: Use 8 bit access burst
default format is four access bursts
BS_CV_MAX
: Countdown Value = 15
PAN description = present
PAN_DEC
PAN_INC
PAN_MAX
: Max value for counter N3102= 5
: End GPRS Cell Options
: GPRS Power Control Param structure
1000 ALPHA = 8 x 0,1
01000 T_AVG_W = 8
00000 T_AVG_T = 0
1 PC_MEAS_CHAN
: Downlink Measurement shall be made on PDCH
0100 N_AVG_I
: 2 exp (4/2)
: End GPRS Power Control Param structure
0110000
spare padding
: 0
_____[ 8 ]___[ 11:52:42,438 ]___[ DOWN ]____[ BCCH ]______________________________
06 1b aa b2 62 f2 10 31 04 40 04 3c 55 65 08 a5 00 00 3c 2b 2b 2b
06
0-------000-------0110
direction from
TransactionID
Protocol Discrim.
: originating site
: 0
: radio resource management messages
1b
00011011
MESSAGE TYPE
: SYSTEM INFORMATION TYPE 3
: Cell Identity
aa 10101010 Cell identity value1: Hex-Wert verwenden
b2 10110010 Cell identity value2: Hex-Wert verwenden
: Location Area Identification
62 ----0010 Mobile CC digit 1
0110---- Mobile CC digit 2
f2 ----0010 Mobile CC digit 3
: 2
: 6
: 2
10
1111-------0000
0001----
Mobile NC digit 3
Mobile NC digit 1
Mobile NC digit 2
: 15
: 0
: 1
31
04
00110001
00000100
Loc. area code (LAC) = ID of MSC (hex)
Loc. area code (LAC) = ID of BSC (hex)
: Control Channel Description
40 0------- 1 spare bit
: 0
-1------ MSs in the cell shall apply IMSI attach and detach procedure
--000--- Number of blocks
: 0 reserved for access grant
-----000 1 basic physical channel used for CCCH not combined with SDCCHs
04
00000--- spare bits
: 5
-----100 6 multi frames period for transmission PAGING REQUEST messages to the
same paging subgroup
3c
00111100
T3212 TimeOut value : 60 deci hours
: Cell Options BCCH,
55 0------- 1 spare bit
: 0
-1------ PWRC Power control indicator is set
--01---- MSs shall use uplink discontinous transmission
----0101 Radio Link Timeout : 24
: Cell Selection Parameters;
65 011----- Cell Resel. Hyster. : 6 dB RXLEV hysteresis for level average (LA) reselection
---00101 Max Tx power level : Mobile may use 5
08 0------- Addition. Reselect Param ind: in SI4 rest octets, i.p., and SI7 and SI8
rest octets, ...
-0------ New establishment cause is not supported
--001000 RXLEV ACCESS MIN
: -110 +8 db permitted
: RACH Control Parameters
a5 10------ Max. of retransm.
: 4
--1001-- used to spread TX
: 12 slots
------0- The cell is barred : no
-------1 Call reestablishment in cell is not allowed
00
-----0-00000--------00
Emergency Call EC10 : allowed
Acc.contr.cl. 11-15 : 0/1 access permitted/forbidden
Acc.contr.cl.
8-9 : 0/1 access permitted/forbidden
00
00000000
Acc.contr.cl.
0-7 : 0/1 access permitted/forbidden
: SI 3 Restoktett
0 Selection Parameters not present
0 Power Offset not present
1 System Information 2ter Indicator not present
1 Early Classmark Sending Control present
1 Scheduling if and where not present
1 High: GPRS indicator = present
: RA COLOUR
000 Routing Area colour = 0
: SI13 Position
0 SYSTEM INFORMATION TYPE 13 message is sent on BCCH Norm;
10101100 spare bits
: End SI 3 Restoktett
_____[ 9 ]___[ 11:52:45,270 ]___[ DOWN ]____[ BCCH ]______________________________
06 1b aa b2 62 f2 10 31 04 40 04 3c 55 65 08 a5 00 00 3c 2b 2b 2b
06
0-------000-------0110
direction from
TransactionID
Protocol Discrim.
: originating site
: 0
: radio resource management messages
1b
00011011
MESSAGE TYPE
: SYSTEM INFORMATION TYPE 3
: Cell Identity
aa 10101010 Cell identity value1: Hex-Wert verwenden
b2 10110010 Cell identity value2: Hex-Wert verwenden
: Location Area Identification
62 ----0010 Mobile CC digit 1
0110---- Mobile CC digit 2
f2 ----0010 Mobile CC digit 3
: 2
: 6
: 2
10
1111-------0000
0001----
Mobile NC digit 3
Mobile NC digit 1
Mobile NC digit 2
: 15
: 0
: 1
31
04
00110001
00000100
Loc. area code (LAC) = ID of MSC (hex)
Loc. area code (LAC) = ID of BSC (hex)
: Control Channel Description
40 0------- 1 spare bit
: 0
-1------ MSs in the cell shall apply IMSI attach and detach procedure
--000--- Number of blocks
: 0 reserved for access grant
-----000 1 basic physical channel used for CCCH not combined with SDCCHs
04
00000--- spare bits
: 5
-----100 6 multi frames period for transmission PAGING REQUEST messages to the
same paging subgroup
3c
00111100
T3212 TimeOut value : 60 deci hours
: Cell Options BCCH,
55 0------- 1 spare bit
: 0
-1------ PWRC Power control indicator is set
--01---- MSs shall use uplink discontinous transmission
----0101 Radio Link Timeout : 24
: Cell Selection Parameters;
65 011----- Cell Resel. Hyster. : 6 dB RXLEV hysteresis for level average (LA) reselection
---00101 Max Tx power level : Mobile may use 5
08 0------- Addition. Reselect Param ind: in SI4 rest octets, i.p., and SI7 and SI8
rest octets, ...
-0------ New establishment cause is not supported
--001000 RXLEV ACCESS MIN
: -110 +8 db permitted
: RACH Control Parameters
a5 10------ Max. of retransm.
--1001-- used to spread TX
: 4
: 12 slots
------0-------1
The cell is barred : no
Call reestablishment in cell is not allowed
00
-----0-00000--------00
Emergency Call EC10 : allowed
Acc.contr.cl. 11-15 : 0/1 access permitted/forbidden
Acc.contr.cl.
8-9 : 0/1 access permitted/forbidden
00
00000000
Acc.contr.cl.
0-7 : 0/1 access permitted/forbidden
: SI 3 Restoktett
0 Selection Parameters not present
0 Power Offset not present
1 System Information 2ter Indicator not present
1 Early Classmark Sending Control present
1 Scheduling if and where not present
1 High: GPRS indicator = present
: RA COLOUR
000 Routing Area colour = 0
: SI13 Position
0 SYSTEM INFORMATION TYPE 13 message is sent on BCCH Norm;
10101100 spare bits
: End SI 3 Restoktett
_____[ 10 ]___[ 11:52:46,094 ]___[ DOWN ]____[ PCH ]______________________________
06 21 00 05 f4 64 11 77 9e 2b 2b 2b 2b 2b 2b 2b 2b 2b 2b 2b 2b 2b
06
0-------000-------0110
direction from
TransactionID
Protocol Discrim.
: originating site
: 0
: radio resource management messages
21
00100001
MESSAGE TYPE
: PAGING REQUEST TYPE 1
00
----00-------00
--00---00------
spare bits
Page Mode
Channel Needed
Channel Needed
:
:
:
:
: Mobile Identity 1
05 00000101 length of Mob.ident.:
f4 1111---- Identity Digit 1
:
----0--- No. of ID digits
:
-----100 Type of identity
:
64 01100100 Identity Digit 2,3 :
11 00010001 Identity Digit 4,5 :
77 01110111 Identity Digit 6,7 :
9e 10011110 Identity Digit 8,9 :
0
Normal paging
(first) Any Channel
(second) Any Channel
5
hex value = f, if
even
TMSI/P-TMSI
take hex value
take hex value
take hex value
take hex value
TMSI/P-TMSI
_____[ 11 ]___[ 11:52:46,172 ]___[ DOWN ]____[ CCCH ]______________________________
06 21 00 05 f4 64 10 ae e8 2b 2b 2b 2b 2b 2b 2b 2b 2b 2b 2b 2b 2b
06
0-------000-------0110
direction from
TransactionID
Protocol Discrim.
: originating site
: 0
: radio resource management messages
21
00100001
MESSAGE TYPE
: PAGING REQUEST TYPE 1
00
----00-------00
--00---00------
spare bits
Page Mode
Channel Needed
Channel Needed
:
:
:
:
0
Normal paging
(first) Any Channel
(second) Any Channel
: Mobile Identity 1
05 00000101 length of Mob.ident.: 5
f4
64
10
ae
e8
1111-------0-------100
01100100
00010000
10101110
11101000
Identity Digit 1
No. of ID digits
Type of identity
Identity Digit 2,3
Identity Digit 4,5
Identity Digit 6,7
Identity Digit 8,9
:
:
:
:
:
:
:
hex value = f, if
even
TMSI/P-TMSI
take hex value
take hex value
take hex value
take hex value
TMSI/P-TMSI
_____[ 12 ]___[ 11:52:46,273 ]___[ DOWN ]____[ BCCH ]______________________________
06 1c 62 f2 10 31 04 65 08 a5 00 00 01 2b 2b 2b 2b 2b 2b 2b 2b 2b
06
0-------000-------0110
direction from
TransactionID
Protocol Discrim.
: originating site
: 0
: radio resource management messages
1c
00011100
MESSAGE TYPE
: SYSTEM INFORMATION TYPE 4
: Location Area Identification
62 ----0010 Mobile CC digit 1
0110---- Mobile CC digit 2
f2 ----0010 Mobile CC digit 3
: 2
: 6
: 2
10
1111-------0000
0001----
Mobile NC digit 3
Mobile NC digit 1
Mobile NC digit 2
: 15
: 0
: 1
31
04
00110001
00000100
Loc. area code (LAI), ID of MSC (hex)
Loc. area code (LAI), ID of BSC (hex)
: Cell Selection Parameters
65 011----- Cell Reselect Hyst. : 6 dB RXLEV hyst. For LA re-select
---00101 Max Tx power level : MS may use 5
08
0-------0-------001000
No Additional cells in SysInfo 7-8
New establishm.cause: not supported
RXLEV ACCESS MIN permitted = -110+8dB
: RACH Control Parameters
a5 10------ Max. of retransmissions
--1001-- 12 slots used to spread TX
------0- The cell is barred : no
-------1 Call reestab.in cell: not allowed
00
-----0-00000--forbidden
------00
forbidden
00 00000000
forbidden
Emergency Call EC 10: allowed
Acc. ctrl class11-15: bit pattern,0 = access permitted, 1 = access
Acc. ctrl class 8-9 : bit pattern,0 = access permitted, 1 = access
Acc. ctrl class 0-7 : bit pattern,0 = access permitted, 1 = access
: SI4 Rest Octets
: SI4 Rest Octets_O
: Optional selection parameters
0 Selection Parameters = not present
: End Optional selection parameters
: Optional Power offset
0 Power Offset = not present
: End Optional Power offset
: GPRS Indicator
0 High: GPRS indicator = present
: RA COLOUR
000 Routing Area colour = 0
: SI13 Position
0 SYSTEM INFORMATION TYPE 13 message is sent on BCCH Norm;
: End GPRS Indicator
: End SI4 Rest Octets_O
: Break Indicator
1 High Additional parameters, "SI4 Rest Octets_S" are sent in SYSTEM
INFORMATION TYPE 7 and 8
: End SI4 Restoctet
_____[ 13 ]___[ 11:52:46,484 ]___[ DOWN ]____[ BCCH ]______________________________
06 19 00 00 00 20 00 00 00 00 00 00 00 10 20 00 20 00 a5 00 00 2b
06
0-------000-------0110
direction from
TransactionID
Protocol Discrim.
19
00011001
MESSAGE TYPE
: originating site
: 0
: radio resource management messages
: SYSTEM INFORMATION TYPE 1
: Cell Channel Description
00 00------ Format Type
--00---- 2 spare bits
: Bit Map 0 format
: 0
20
10
20
20
:
:
:
:
ARFCN
ARFCN
ARFCN
ARFCN
:
:
:
:
4
12
no
not allowed
--1-------1-----1------1-----
Cell
Cell
Cell
Cell
Allocation
Allocation
Allocation
Allocation
: RACH Control Parameters
a5 10------ Max. of retransmiss
--1001-- slots to spread TX
------0- The cell is barred
-------1 Call reestabl.i.cell
102
37
30
14
00
00000-------0-------00
Acc. contr. cl. 11-15: Bitmuster: 0 Zugr.erl.,1 Zugr.n.erl.
Emergency Call EC 10 : allowed
Acc. contr. cl. 8-9 : Bitmuster: 0 Zugr.erl.,1 Zugr.n.erl.
00
00000000
Acc. contr. cl. 0-7
: Bitmuster: 0 Zugr.erl.,1 Zugr.n.erl.
: NCH Position
0 no NCH Position
0101011 spare padding
_____[ 14 ]___[ 11:52:46,723 ]___[ DOWN ]____[ BCCH ]______________________________
06 1a 00 00 00 00 04 10 00 00 00 00 00 c0 a2 9d 00 00 08 a5 00 00
06
0-------000-------0110
direction from
TransactionID
Protocol Discrim.
: originating site
: 0
: radio resource management messages
1a
00011010
MESSAGHE TYPE
: SYSTEM INFORMATION TYPE 2
00
--0-------0----
Extension Indicator : The IE carries the complete BA
BCCH alloc. sequ.num: 0
04
10
c0
-----1----1---1-------1-----1--------1----------11---------1----
BCCH
BCCH
BCCH
BCCH
BCCH
BCCH
BCCH
BCCH
BCCH
a2
9d
alloc.
alloc.
alloc.
alloc.
alloc.
alloc.
alloc.
alloc.
alloc.
RF
RF
RF
RF
RF
RF
RF
RF
RF
chan.:
chan.:
chan.:
chan.:
chan.:
chan.:
chan.:
chan.:
chan.:
91
85
40
39
32
30
26
24
21
----1-------1--------1
BCCH alloc. RF chan.: 20
BCCH alloc. RF chan.: 19
BCCH alloc. RF chan.: 17
08
----1---
BCCH carrier with NCC = 3 is permitted for monitoring;
a5
10-------1001-------0-------1
Max. of retransmiss.: 4
12 slots used to spread TX
The cell is barred : no
Call reestablishment in cell is not allowed
00
-----0-00000--------00
Emergency Call EC 10: allowed
acc ctrl class 11-15: 0/1 access permitted/forbidden
acc ctrl class 8-9 : 0/1 access permitted/forbidden
00
00000000
acc ctrl class
0-7 : 0/1 access permitted/forbidden
_____[ 15 ]___[ 11:52:46,734 ]___[ DOWN ]____[ CCCH ]______________________________
06 39 03 71 90 00 84 3b ab 02 61 80 1e 9c 3d 37 01 01 0d 2b 2b 2b
06
0-------000-------0110
direction from
TransactionID
Protocol Discrim.
: originating site
: 0
: radio resource management messages
_____[ 16 ]___[ 11:52:46,742 ]___[ UP ]___________________________________________
06 27 01 03 33 19 81 05 f4 64 11 77 9e
06
0-------000-------0110
direction from
TransactionID
Protocol Discrim.
: originating site
: 0
: radio resource management messages
27
0-------0-------100111
1 spare bit
: 0
Send sequence number: value
MESSAGE TYPE
: PAGING RESPONSE
: Ciphering Key Sequence Number
01 ----0--- 1 spare bit
: 0
-----001 Ciph. key sequ. num.: 1 (7=no key available)
0000---- 4 spare bits
: 0
: Mobile Station Classmark 2
03 00000011 lgth of MS Cl.Mark2 : 3
33
0-------01-------1-------0-------011
1 spare
: 0
Revision Level
: Used by phase 2 mobile stations
"Controlled Early Classmark Sending" option is implemented in the MS
Encryp.Algor. A5_1 : available
RF power capability : Class 4, handheld
19
0-------0-------01-------1-------0-------0-------1
1 spare bit
: 0
pseudo-synch.capab. : not present
SS Screening Indic. : phase 2 error handling
Mobile station supports mobile terminated point to point SMS
no VoiceBroadcastService (VBS) capability or no notifications wanted
no VoiceGroupCallService (VGCS) capability or no notifications wanted
The MS does support the E-GSM or R-GSM
81
-0-------0-------0-------0-------0-------0-
1 spare bit
: 0
LocationServiceValueAdded Capability not supported
1 spare bit
: 0
SoLSA Capability
: not supported
Network initiated MO CM connection request not supported.
encryp.algorith.A5/3: not available
-------1
encryp.algorith.A5/2: available
: Mobile Identity
05
f4
64
11
77
9e
00000101
1111-------0-------100
01100100
00010001
01110111
10011110
length of Mob. ident:
Identity Digit 1
:
No. of ID digits
:
Type of identity
:
Identity Digit 2,3 :
Identity Digit 4,5 :
Identity Digit 6,7 :
Identity Digit 8,9 :
5
15
even
TMSI/P-TMSI
take hex value
take hex value
take hex value
take hex value
_____[ 17 ]___[ 11:52:46,926 ]___[ DOWN ]____[ SACCH ]______________________________
06 1e cd 3a 62 f2 10 31 04 55 08 2b 2b 2b 2b 2b 2b 2b 00 00 08 1c
06
0-------000-------0110
direction from
TransactionID
Protocol Discrim.
: originating site
: 0
: radio resource management messages
1e
00011110
MESSAGE TYPE
: SYSTEM INFORMATION TYPE 6
: Cell Identity
cd 11001101 Cell identity value1, Hex Wert
3a 00111010 Cell identity value2, Hex Wert
: Location Area Identification
62 ----0010 MCC digit 1
0110---- MCC digit 2
f2 ----0010 MCC digit 3
: 2
: 6
: 2
10
1111-------0000
0001----
MNC digit 3
MNC digit 1
MNC digit 2
: 15
: 0
: 1
31
04
00110001
00000100
Location area code (LAI), Number of MSC
Location area code (LAI), Number of BSC
: Cell Options (SACH)
55 0------- 1 spare bit
: 0
-1------ Power control indic.: is set
--01---- MSs shall use uplink discont.transmission
----0101 Radio Link Timeout : 24
: NCC Permitted
08 ----1--- BCCH carrier with NCC = 3 is permitted for monitoring;
_____[ 18 ]___[ 11:52:47,055 ]___[ UP ]____[ SDCCH ]______________________________
06 16 03 33 19 81 20 02 60 14
06
0-------000-------0110
direction from
TransactionID
Protocol Discrim.
: originating site
: 0
: radio resource management messages
16
00010110
MESSAGE TYPE
: CLASSMARK CHANGE
: Mobile Station Classmark 2
03 00000011 length
33
0-------01-------1----
: 3
1 spare
: 0
Revision Level
: Used by phase 2 mobile stations
"Controlled Early Classmark Sending" option is implemented in the MS
----0-------011
Encryp.Algor. A5_1 : available
RF power capability : Class 4, handheld
19
0-------0-------01-------1-------0-------0-------1
1 spare bit
: 0
pseudo-synch.capab. : not present
SS Screening Indic. : phase 2 error handling
Mobile station supports mobile terminated point to point SMS
no VoiceBroadcastService (VBS) capability or no notifications wanted
no VoiceGroupCallService (VGCS) capability or no notifications wanted
The MS does support the E-GSM or R-GSM
81
1-------0-------0-------0-------0-------0-------0-------1
The MS does support any options that are indicated in CM3
1 spare bit
: 0
LocationServiceValueAdded Capability not supported
1 spare bit
: 0
SoLSA Capability
: not supported
Network initiated MO CM connection request not supported.
encryp.algorith.A5/3: not available
encryp.algorith.A5/2: available
20
00100000
INFORMATION ELEMENT : CLASSMARK 3
02
00000010
length
60
0110-------0-------0-------0-------0
P-GSM, E-GSM or R-GSM supported, DCS 1800 not supported
encryption algorithm A5/7 not available
encryption algorithm A5/6 not available
encryption algorithm A5/5 not available
encryption algorithm A5/4 not available
14
0001-------0100
Associated Radio capability 1 = 1
Associated Radio capability 2 = 4
: 2
_____[ 19 ]___[ 11:52:47,324 ]___[ DOWN ]____[ SDCCH ]______________________________
06 13
06
13
0-------000-------0110
00010011
direction from
TransactionID
Protocol Discrim.
MESSAGE TYPE
:
:
:
:
originating site
0
radio resource management messages
CLASSMARK ENQUIRY
_____[ 20 ]___[ 11:52:47,324 ]___[ UP ]___________________________________________
06 16 03 33 19 81 20 02 60 14
06
0-------000-------0110
direction from
TransactionID
Protocol Discrim.
: originating site
: 0
: radio resource management messages
16
00010110
MESSAGE TYPE
: CLASSMARK CHANGE
: Mobile Station Classmark 2
03 00000011 length
: 3
33
0-------01-------1-------0-------011
1 spare
: 0
Revision Level
: Used by phase 2 mobile stations
"Controlled Early Classmark Sending" option is implemented in the MS
Encryp.Algor. A5_1 : available
RF power capability : Class 4, handheld
19
0-------0-------01----
1 spare bit
: 0
pseudo-synch.capab. : not present
SS Screening Indic. : phase 2 error handling
----1-------0-------0-------1
Mobile station supports mobile terminated point to point SMS
no VoiceBroadcastService (VBS) capability or no notifications wanted
no VoiceGroupCallService (VGCS) capability or no notifications wanted
The MS does support the E-GSM or R-GSM
81
1-------0-------0-------0-------0-------0-------0-------1
The MS does support any options that are indicated in CM3
1 spare bit
: 0
LocationServiceValueAdded Capability not supported
1 spare bit
: 0
SoLSA Capability
: not supported
Network initiated MO CM connection request not supported.
encryp.algorith.A5/3: not available
encryp.algorith.A5/2: available
20
00100000
INFORMATION ELEMENT : CLASSMARK 3
02
00000010
length
60
0110-------0-------0-------0-------0
P-GSM, E-GSM or R-GSM supported, DCS 1800 not supported
encryption algorithm A5/7 not available
encryption algorithm A5/6 not available
encryption algorithm A5/5 not available
encryption algorithm A5/4 not available
14
0001-------0100
Associated Radio capability 1 = 1
Associated Radio capability 2 = 4
: 2
_____[ 21 ]___[ 11:52:47,395 ]___[ DOWN ]____[ SACCH ]______________________________
06 1d 10 00 00 00 04 10 00 00 00 00 00 c0 82 9d 00 00
06
0-------000-------0110
direction from
TransactionID
Protocol Discrim.
: originating site
: 0
: radio resource management messages
1d
00011101
MESSAGE TYPE
: SYSTEM INFORMATION TYPE 5
10
00-------0-------1----
Format Type
: Bit Map 0 format
Extension Indicator : The IE carries the complete BA
BCCH allocation sequence number indication 1
04
10
c0
-----1----1---1-------1-----1------------11---------1-------1-------1--------1
BCCH
BCCH
BCCH
BCCH
BCCH
BCCH
BCCH
BCCH
BCCH
BCCH
BCCH
82
9d
alloc.
alloc.
alloc.
alloc.
alloc.
alloc.
alloc.
alloc.
alloc.
alloc.
alloc.
RF
RF
RF
RF
RF
RF
RF
RF
RF
RF
RF
chan.:
chan.:
chan.:
chan.:
chan.:
chan.:
chan.:
chan.:
chan.:
chan.:
chan.:
91
85
40
39
32
26
24
21
20
19
17
_____[ 22 ]___[ 11:52:47,445 ]___[ UP ]___________________________________________
06 15 94 14 01 54 0b a9 a5 a3 00 e9 47 7c 91 bc 00 00
06
0-------000-------0110
direction from
TransactionID
Protocol Discrim.
: originating site
: 0
: radio resource management messages
15
00010101
MESSAGE TYPE
: MEASUREMENT REPORT
94
1-------
BA used
: yes
14
-0-------010100
Discontinous Transmission was not used
RXLEV-FULL-SERVING-CELL= (-110 + 20) dB
0-------0-------010100
0------000------000
101
spare
: 0
MEAS-VALID
: yes
RXLEV-SUB-SERVING-CELL = (-110 + 20) dB
spare
: 0
RX-QUAL-FULL-SERVING-CELL = ~0,14% error bit
RX-QUAL-SUB -SERVING-CELL = ~0,14% error bit
Number of neighbouring cell measurements = 5
010100
00001
011101
RXLEV-Neighbour-CELL 1 = (-110 + 20) dB
BCCH-FREQ-NCELL 1
: 1
Base station identity code of the 1'th neighbouring cell = 29
010011
01001
011010
RXLEV-Neighbour-CELL 2 = (-110 + 19) dB
BCCH-FREQ-NCELL 2
: 9
Base station identity code of the 2'th neighbouring cell= 26
001100
00000
011101
RXLEV-Neighbour-CELL 3 = (-110 + 12) dB
BCCH-FREQ-NCELL 3
: 0
Base station identity code of the 3'th neighbouring cell = 29
001010
00111
011111
RXLEV-Neighbour-CELL 4 = (-110 + 10) dB
BCCH-FREQ-NCELL 4
: 7
Base station identity code of the 4'th neighbouring cell = 31
001001
00011
011110
RXLEV-Neighbour-CELL 5 = (-110 + 9) dB
BCCH-FREQ-NCELL 5
: 3
Base station identity code of the 5'th neighbouring cell = 30
000000
00000
000000
RXLEV-Neighbour-CELL 6 = (-110 + 0) dB
BCCH-FREQ-NCELL 6
: 0
Base station identity code of the 6'th neighbouring cellt = = 0
_____[ 23 ]___[ 11:52:47,566 ]___[ DOWN ]____[ SDCCH ]______________________________
06 35 11
06
0-------000-------0110
direction from
TransactionID
Protocol Discrim.
: originating site
: 0
: radio resource management messages
35
00110101
MESSAGE TYPE
: CIPHERING MODE COMMAND
11
----000-------1
000-------1----
cipher with algorithm A5/1
Start ciphering
spare
: 0
Cipher Response
: IMEISV shall be included
_____[ 24 ]___[ 11:52:47,566 ]___[ UP ]___________________________________________
06 32 17 09 33 23 81 81 32 07 31 09 f0
06
32
0-------000-------0110
00110010
direction from
TransactionID
Protocol Discrim.
MESSAGE TYPE
:
:
:
:
originating site
0
radio resource management messages
CIPHERING MODE COMPLETE
17
00010111
INFORMATIONS ELEMENT: Mobile Identity
09
00001001
length of Mob.ident.3: 9
33
----0-------011
No. of ID digits
Type of identity
: even
: IMEISV
23
81
81
32
07
31
09
f0
0011-------0011
0010-------0001
1000-------0001
1000-------0010
0011-------0111
0000-------0001
0011-------1001
0000-------0000
1111----
Identity
Identity
Identity
Identity
Identity
Identity
Identity
Identity
Identity
Identity
Identity
Identity
Identity
Identity
Identity
Identity
Identity
Digit
Digit
Digit
Digit
Digit
Digit
Digit
Digit
Digit
Digit
Digit
Digit
Digit
Digit
Digit
Digit
Digit
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
3
3
2
1
8
1
8
2
3
7
0
1
3
9
0
0
15
_____[ 25 ]___[ 11:52:47,863 ]___[ DOWN ]____[ SACCH ]______________________________
06 1e cd 3a 62 f2 10 31 04 55 08 2b 2b 2b 2b 2b 2b 2b 00 00 08 1c
06
0-------000-------0110
direction from
TransactionID
Protocol Discrim.
: originating site
: 0
: radio resource management messages
1e
00011110
MESSAGE TYPE
: SYSTEM INFORMATION TYPE 6
: Cell Identity
cd 11001101 Cell identity value1, Hex Wert
3a 00111010 Cell identity value2, Hex Wert
: Location Area Identification
62 ----0010 MCC digit 1
0110---- MCC digit 2
f2 ----0010 MCC digit 3
: 2
: 6
: 2
10
1111-------0000
0001----
MNC digit 3
MNC digit 1
MNC digit 2
: 15
: 0
: 1
31
04
00110001
00000100
Location area code (LAI), Number of MSC
Location area code (LAI), Number of BSC
: Cell Options (SACH)
55 0------- 1 spare bit
: 0
-1------ Power control indic.: is set
--01---- MSs shall use uplink discont.transmission
----0101 Radio Link Timeout : 24
: NCC Permitted
08 ----1--- BCCH carrier with NCC = 3 is permitted for monitoring;
_____[ 26 ]___[ 11:52:47,914 ]___[ UP ]___________________________________________
06 15 97 17 01 55 4b 49 05 d3 00 e9 47 7c 81 bc 00 00
06
0-------000-------0110
direction from
TransactionID
Protocol Discrim.
: originating site
: 0
: radio resource management messages
15
00010101
MESSAGE TYPE
: MEASUREMENT REPORT
97
1-------
BA used
: yes
17
-0-------010111
Discontinous Transmission was not used
RXLEV-FULL-SERVING-CELL= (-110 + 23) dB
0-------0-------010111
0------000------000
101
spare
: 0
MEAS-VALID
: yes
RXLEV-SUB-SERVING-CELL = (-110 + 23) dB
spare
: 0
RX-QUAL-FULL-SERVING-CELL = ~0,14% error bit
RX-QUAL-SUB -SERVING-CELL = ~0,14% error bit
Number of neighbouring cell measurements = 5
010101
01001
011010
RXLEV-Neighbour-CELL 1 = (-110 + 21) dB
BCCH-FREQ-NCELL 1
: 9
Base station identity code of the 1'th neighbouring cell = 26
010010
00001
011101
RXLEV-Neighbour-CELL 2 = (-110 + 18) dB
BCCH-FREQ-NCELL 2
: 1
Base station identity code of the 2'th neighbouring cell= 29
001100
00000
011101
RXLEV-Neighbour-CELL 3 = (-110 + 12) dB
BCCH-FREQ-NCELL 3
: 0
Base station identity code of the 3'th neighbouring cell = 29
001010
00111
011111
RXLEV-Neighbour-CELL 4 = (-110 + 10) dB
BCCH-FREQ-NCELL 4
: 7
Base station identity code of the 4'th neighbouring cell = 31
001000
00011
011110
RXLEV-Neighbour-CELL 5 = (-110 + 8) dB
BCCH-FREQ-NCELL 5
: 3
Base station identity code of the 5'th neighbouring cell = 30
000000
00000
000000
RXLEV-Neighbour-CELL 6 = (-110 + 0) dB
BCCH-FREQ-NCELL 6
: 0
Base station identity code of the 6'th neighbouring cellt = = 0
_____[ 27 ]___[ 11:52:48,258 ]___[ DOWN ]____[ SDCCH ]______________________________
13 05 04 01 a0 5c 09 11 81 94 33 57 12 80 51 f6 7d 02 91 81
13
0-------001-------0011
00------
direction from
TransactionID
Protocol Discrim.
SendSequenceNumber
:
:
:
:
--000101
MESSAGE TYPE
: SETUP
00000100
00000001
1-------01-------0-------0-------000
INFORMATION ELEMENT
length
Extension
Radio Channel Req.
Coding Standard
Transfer Mode
Info Transfer Cap.
:
:
:
:
:
:
:
Bearer capability
1
1
full rate support only MS
GSM standard coding
Circuit Mode
speech
01011100
00001001
0-------001-------0001
81 1-------00-------000-------01
94..f6
INFORMATION ELEMENT
length
Extension
Type of number
Numb. plan id.
Extension
Present.indic.
spare
Present.indic.
number
:
:
:
:
:
:
:
:
:
:
Calling party BCD number
9
0
international number
ISDN/telephony numb. pl. (Rec. E.164/E.163)
1
Presentation allowed
0
User-provided, verified and passed
4933752108156
05
04
01
a0
5c
09
11
originating site
1
Call control and call related SS messages
0
7d
02
91
81
01111101
00000010
1-------00-------100-------01
10000001
INFORMATION ELEMENT
length
Extension
Coding standard
Interpret.i.ch.
Present.method
High layer char.
:
:
:
:
:
:
:
High Layer Compatibility
2
1
CCITT standardized coding
First high layer char.id. to be used
High Layer protocol profile
Telephony
_____[ 28 ]___[ 11:52:48,258 ]___[ UP ]___________________________________________
93 08 04 04 60 02 00 81
93
08
04
04
60
02
00
81
1-------001-------0011
00------
direction to
TransactionID
Protocol Discrim.
SendSequenceNumber
:
:
:
:
--001000
MESSAGE TYPE
: CALL CONFIRMED
00000100
00000100
0-------
INFORMATION ELEMENT : Bearer capability
length
: 4
Extension
: 0
-11-------0-------0-------000
0-------0-------00-------0010
0-------0-------00-------0000
1-------0-------00-------0001
Radio Channel Req.
Coding Standard
Transfer Mode
Info Transfer Cap.
Extension
Coding
Spare
speech Vers. indic.
Extension
Coding
Spare
speech Vers. indic.
Extension
Coding
Spare
speech Vers. indic.
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
originating site
1
Call control and call related SS messages
0
dual rate support MS/full rate preferred
GSM standard coding
Circuit Mode
speech
0
octet used for extension of inf. transf. capab.
00
GSM full rate speech version 2
0
octet used for extension of inf. transf. capab.
00
GSM full rate speech version 1
1
octet used for extension of inf. transf. capab.
00
GSM half rate speech version 1
_____[ 29 ]___[ 11:52:48,336 ]___[ DOWN ]____[ SACCH ]______________________________
06 1d 10 00 00 00 04 10 00 00 00 00 00 c0 82 9d 00 00
06
0-------000-------0110
direction from
TransactionID
Protocol Discrim.
: originating site
: 0
: radio resource management messages
1d
00011101
MESSAGE TYPE
: SYSTEM INFORMATION TYPE 5
10
00-------0-------1----
Format Type
: Bit Map 0 format
Extension Indicator : The IE carries the complete BA
BCCH allocation sequence number indication 1
04
10
c0
-----1----1---1-------1-----1------------11---------1-------1-------1--------1
BCCH
BCCH
BCCH
BCCH
BCCH
BCCH
BCCH
BCCH
BCCH
BCCH
BCCH
82
9d
alloc.
alloc.
alloc.
alloc.
alloc.
alloc.
alloc.
alloc.
alloc.
alloc.
alloc.
RF
RF
RF
RF
RF
RF
RF
RF
RF
RF
RF
chan.:
chan.:
chan.:
chan.:
chan.:
chan.:
chan.:
chan.:
chan.:
chan.:
chan.:
91
85
40
39
32
26
24
21
20
19
17
_____[ 30 ]___[ 11:52:48,387 ]___[ UP ]___________________________________________
06 15 96 16 01 96 4b 47 85 d3 06 f1 60 74 a3 be 49 5c
06
0-------000-------0110
direction from
TransactionID
Protocol Discrim.
: originating site
: 0
: radio resource management messages
15
00010101
MESSAGE TYPE
: MEASUREMENT REPORT
96
1-------0-------010110
BA used
: yes
Discontinous Transmission was not used
RXLEV-FULL-SERVING-CELL= (-110 + 22) dB
16
0-------0-------010110
0------000------000
110
spare
: 0
MEAS-VALID
: yes
RXLEV-SUB-SERVING-CELL = (-110 + 22) dB
spare
: 0
RX-QUAL-FULL-SERVING-CELL = ~0,14% error bit
RX-QUAL-SUB -SERVING-CELL = ~0,14% error bit
Number of neighbouring cell measurements = 6
010110
01001
011010
RXLEV-Neighbour-CELL 1 = (-110 + 22) dB
BCCH-FREQ-NCELL 1
: 9
Base station identity code of the 1'th neighbouring cell = 26
001111
00001
011101
RXLEV-Neighbour-CELL 2 = (-110 + 15) dB
BCCH-FREQ-NCELL 2
: 1
Base station identity code of the 2'th neighbouring cell= 29
001100
00011
011110
RXLEV-Neighbour-CELL 3 = (-110 + 12) dB
BCCH-FREQ-NCELL 3
: 3
Base station identity code of the 3'th neighbouring cell = 30
001011
00000
011101
RXLEV-Neighbour-CELL 4 = (-110 + 11) dB
BCCH-FREQ-NCELL 4
: 0
Base station identity code of the 4'th neighbouring cell = 29
001010
00111
011111
RXLEV-Neighbour-CELL 5 = (-110 + 10) dB
BCCH-FREQ-NCELL 5
: 7
Base station identity code of the 5'th neighbouring cell = 31
001001
00101
011100
RXLEV-Neighbour-CELL 6 = (-110 + 9) dB
BCCH-FREQ-NCELL 6
: 5
Base station identity code of the 6'th neighbouring cellt = = 28
_____[ 31 ]___[ 11:52:48,809 ]___[ DOWN ]____[ SACCH ]______________________________
06 1e cd 3a 62 f2 10 31 04 55 08 2b 2b 2b 2b 2b 2b 2b 00 00 08 1c
06
0-------000-------0110
direction from
TransactionID
Protocol Discrim.
: originating site
: 0
: radio resource management messages
1e
00011110
MESSAGE TYPE
: SYSTEM INFORMATION TYPE 6
: Cell Identity
cd 11001101 Cell identity value1, Hex Wert
3a 00111010 Cell identity value2, Hex Wert
: Location Area Identification
62 ----0010 MCC digit 1
0110---- MCC digit 2
: 2
: 6
f2
----0010
MCC digit 3
: 2
10
1111-------0000
0001----
MNC digit 3
MNC digit 1
MNC digit 2
: 15
: 0
: 1
31
04
00110001
00000100
Location area code (LAI), Number of MSC
Location area code (LAI), Number of BSC
: Cell Options (SACH)
55 0------- 1 spare bit
: 0
-1------ Power control indic.: is set
--01---- MSs shall use uplink discont.transmission
----0101 Radio Link Timeout : 24
: NCC Permitted
08 ----1--- BCCH carrier with NCC = 3 is permitted for monitoring;
_____[ 32 ]___[ 11:52:48,855 ]___[ UP ]___________________________________________
06 15 96 16 01 8e 4b 47 0d e3 82 e9 87 7c b2 b8 40 1d
06
0-------000-------0110
direction from
TransactionID
Protocol Discrim.
: originating site
: 0
: radio resource management messages
15
00010101
MESSAGE TYPE
: MEASUREMENT REPORT
96
1-------0-------010110
BA used
: yes
Discontinous Transmission was not used
RXLEV-FULL-SERVING-CELL= (-110 + 22) dB
16
0-------0-------010110
0------000------000
110
spare
: 0
MEAS-VALID
: yes
RXLEV-SUB-SERVING-CELL = (-110 + 22) dB
spare
: 0
RX-QUAL-FULL-SERVING-CELL = ~0,14% error bit
RX-QUAL-SUB -SERVING-CELL = ~0,14% error bit
Number of neighbouring cell measurements = 6
001110
01001
011010
RXLEV-Neighbour-CELL 1 = (-110 + 14) dB
BCCH-FREQ-NCELL 1
: 9
Base station identity code of the 1'th neighbouring cell = 26
001110
00011
011110
RXLEV-Neighbour-CELL 2 = (-110 + 14) dB
BCCH-FREQ-NCELL 2
: 3
Base station identity code of the 2'th neighbouring cell= 30
001110
00001
011101
RXLEV-Neighbour-CELL 3 = (-110 + 14) dB
BCCH-FREQ-NCELL 3
: 1
Base station identity code of the 3'th neighbouring cell = 29
001100
00111
011111
RXLEV-Neighbour-CELL 4 = (-110 + 12) dB
BCCH-FREQ-NCELL 4
: 7
Base station identity code of the 4'th neighbouring cell = 31
001011
00101
011100
RXLEV-Neighbour-CELL 5 = (-110 + 11) dB
BCCH-FREQ-NCELL 5
: 5
Base station identity code of the 5'th neighbouring cell = 28
001000
00000
011101
RXLEV-Neighbour-CELL 6 = (-110 + 8) dB
BCCH-FREQ-NCELL 6
: 0
Base station identity code of the 6'th neighbouring cellt = = 29
_____[ 33 ]___[ 11:52:49,219 ]___[ DOWN ]____[ SDCCH ]______________________________
06 2e 0d 90 40 05 05 05 8c 07 10 24 70 63 21
06
0-------000-------0110
direction from
TransactionID
Protocol Discrim.
: originating site
: 0
: radio resource management messages
2e
00101110
MESSAGE TYPE
: ASSIGNMENT COMMAND
: Channel Description 2
0d 00001--- Channel type and TDMA offset = TCH/F + ACCHs
-----101 Timslot number
: 5
90
40
100-------1-------0000
01-------000000
Training sequ. code : 4
Hopping Channel
MAIO high part
MAIO low part
Hopping Sequence Nr.: HSN = 0
: POWER LEVEL
05 000----- spare
---00101 Power level
05
05
8c
07
10
24
70
63
21
: 5
00000101
00000101
10--110--00----------0
00000111
0-------0010000
0-------010010-------0
01110-------000
INFORMATION ELEMENT : FREQUENCY LIST
length
: 5
Range 128 format
spare
Orig ARFCN high
ORIG-ARFCN (middle part)
Orig ARFCN low
W1 high part
W1 low part
W2
W3 high part
W3 low part
W4 high part
01100011
00100001
INFORMATION ELEMENT : CHANNEL MODE
channel mode
: speech full rate or half rate version 2
_____[ 34 ]___[ 11:52:49,219 ]___[ UP ]___________________________________________
06 29 00
06
0-------000-------0110
direction from
TransactionID
Protocol Discrim.
: originating site
: 0
: radio resource management messages
29
00101001
MESSAGE TYPE
: ASSIGNMENT COMPLETE
00
00000000
RR-Cause (reason of event) = Normal event
_____[ 35 ]___[ 11:52:49,398 ]___[ UP ]____[ FACCH_F ]______________________________
93 01
93
01
1-------001-------0011
00------
direction to
TransactionID
Protocol Discrim.
SendSequenceNumber
:
:
:
:
originating site
1
Call control and call related SS messages
0
--000001
MESSAGE TYPE
: ALERTING
_____[ 36 ]___[ 11:52:50,059 ]___[ DOWN ]____[ SACCH ]______________________________
06 1d 10 00 00 00 04 10 00 00 00 00 00 c0 82 9d 00 00
06
0-------000-------0110
direction from
TransactionID
Protocol Discrim.
: originating site
: 0
: radio resource management messages
1d
00011101
MESSAGE TYPE
: SYSTEM INFORMATION TYPE 5
10
00-------0-------1----
Format Type
: Bit Map 0 format
Extension Indicator : The IE carries the complete BA
BCCH allocation sequence number indication 1
04
10
c0
-----1----1---1-------1-----1------------11---------1-------1-------1--------1
BCCH
BCCH
BCCH
BCCH
BCCH
BCCH
BCCH
BCCH
BCCH
BCCH
BCCH
82
9d
alloc.
alloc.
alloc.
alloc.
alloc.
alloc.
alloc.
alloc.
alloc.
alloc.
alloc.
RF
RF
RF
RF
RF
RF
RF
RF
RF
RF
RF
chan.:
chan.:
chan.:
chan.:
chan.:
chan.:
chan.:
chan.:
chan.:
chan.:
chan.:
91
85
40
39
32
26
24
21
20
19
17
_____[ 37 ]___[ 11:52:50,066 ]___[ UP ]___________________________________________
06 15 d3 13 49 97 4b 47 81 d3 82 e9 83 78 c3 be 51 5c
06
0-------000-------0110
direction from
TransactionID
Protocol Discrim.
: originating site
: 0
: radio resource management messages
15
00010101
MESSAGE TYPE
: MEASUREMENT REPORT
d3
1-------1-------010011
BA used
: yes
Discontinous Transmission was used
RXLEV-FULL-SERVING-CELL= (-110 + 19) dB
13
0-------0-------010011
0------100------100
110
spare
: 0
MEAS-VALID
: yes
RXLEV-SUB-SERVING-CELL = (-110 + 19) dB
spare
: 0
RX-QUAL-FULL-SERVING-CELL = ~2,26% error bit
RX-QUAL-SUB -SERVING-CELL = ~2,26% error bit
Number of neighbouring cell measurements = 6
010111
01001
011010
RXLEV-Neighbour-CELL 1 = (-110 + 23) dB
BCCH-FREQ-NCELL 1
: 9
Base station identity code of the 1'th neighbouring cell = 26
001111
00000
011101
RXLEV-Neighbour-CELL 2 = (-110 + 15) dB
BCCH-FREQ-NCELL 2
: 0
Base station identity code of the 2'th neighbouring cell= 29
001110
00001
011101
RXLEV-Neighbour-CELL 3 = (-110 + 14) dB
BCCH-FREQ-NCELL 3
: 1
Base station identity code of the 3'th neighbouring cell = 29
001100
00011
011110
RXLEV-Neighbour-CELL 4 = (-110 + 12) dB
BCCH-FREQ-NCELL 4
: 3
Base station identity code of the 4'th neighbouring cell = 30
001100
00111
011111
RXLEV-Neighbour-CELL 5 = (-110 + 12) dB
BCCH-FREQ-NCELL 5
: 7
Base station identity code of the 5'th neighbouring cell = 31
001010
00101
011100
RXLEV-Neighbour-CELL 6 = (-110 + 10) dB
BCCH-FREQ-NCELL 6
: 5
Base station identity code of the 6'th neighbouring cellt = = 28
_____[ 38 ]___[ 11:52:50,551 ]___[ UP ]____[ SACCH ]______________________________
06 15 d5 16 6d 9b 4b 4a 15 c4 c6 f2 61 75 20 3a 79 df
06
0-------000-------0110
direction from
TransactionID
Protocol Discrim.
: originating site
: 0
: radio resource management messages
15
00010101
MESSAGE TYPE
: MEASUREMENT REPORT
d5
1-------1-------010101
BA used
: yes
Discontinous Transmission was used
RXLEV-FULL-SERVING-CELL= (-110 + 21) dB
16
0-------0-------010110
0------110------110
110
spare
: 0
MEAS-VALID
: yes
RXLEV-SUB-SERVING-CELL = (-110 + 22) dB
spare
: 0
RX-QUAL-FULL-SERVING-CELL = ~9,05% error bit
RX-QUAL-SUB -SERVING-CELL = ~9,05% error bit
Number of neighbouring cell measurements = 6
011011
01001
011010
RXLEV-Neighbour-CELL 1 = (-110 + 27) dB
BCCH-FREQ-NCELL 1
: 9
Base station identity code of the 1'th neighbouring cell = 26
010100
00101
011100
RXLEV-Neighbour-CELL 2 = (-110 + 20) dB
BCCH-FREQ-NCELL 2
: 5
Base station identity code of the 2'th neighbouring cell= 28
010011
00011
011110
RXLEV-Neighbour-CELL 3 = (-110 + 19) dB
BCCH-FREQ-NCELL 3
: 3
Base station identity code of the 3'th neighbouring cell = 30
010011
00001
011101
RXLEV-Neighbour-CELL 4 = (-110 + 19) dB
BCCH-FREQ-NCELL 4
: 1
Base station identity code of the 4'th neighbouring cell = 29
010010
00000
011101
RXLEV-Neighbour-CELL 5 = (-110 + 18) dB
BCCH-FREQ-NCELL 5
: 0
Base station identity code of the 5'th neighbouring cell = 29
001111
00111
011111
RXLEV-Neighbour-CELL 6 = (-110 + 15) dB
BCCH-FREQ-NCELL 6
: 7
Base station identity code of the 6'th neighbouring cellt = = 31
_____[ 39 ]___[ 11:52:51,031 ]___[ UP ]____[ SACCH ]______________________________
06 15 d8 17 6d 9f 4b 4b 05 d5 00 ea 47 7d 11 bc 81 5c
06
0-------000-------0110
direction from
TransactionID
Protocol Discrim.
: originating site
: 0
: radio resource management messages
15
00010101
MESSAGE TYPE
: MEASUREMENT REPORT
d8
1-------1-------011000
BA used
: yes
Discontinous Transmission was used
RXLEV-FULL-SERVING-CELL= (-110 + 24) dB
17
0-------0-------010111
0------110------110
110
spare
: 0
MEAS-VALID
: yes
RXLEV-SUB-SERVING-CELL = (-110 + 23) dB
spare
: 0
RX-QUAL-FULL-SERVING-CELL = ~9,05% error bit
RX-QUAL-SUB -SERVING-CELL = ~9,05% error bit
Number of neighbouring cell measurements = 6
011111
01001
011010
RXLEV-Neighbour-CELL 1 = (-110 + 31) dB
BCCH-FREQ-NCELL 1
: 9
Base station identity code of the 1'th neighbouring cell = 26
010110
00001
011101
RXLEV-Neighbour-CELL 2 = (-110 + 22) dB
BCCH-FREQ-NCELL 2
: 1
Base station identity code of the 2'th neighbouring cell= 29
010100
00000
011101
RXLEV-Neighbour-CELL 3 = (-110 + 20) dB
BCCH-FREQ-NCELL 3
: 0
Base station identity code of the 3'th neighbouring cell = 29
010010
00111
011111
RXLEV-Neighbour-CELL 4 = (-110 + 18) dB
BCCH-FREQ-NCELL 4
: 7
Base station identity code of the 4'th neighbouring cell = 31
010001
00011
011110
RXLEV-Neighbour-CELL 5 = (-110 + 17) dB
BCCH-FREQ-NCELL 5
: 3
Base station identity code of the 5'th neighbouring cell = 30
010000
00101
011100
RXLEV-Neighbour-CELL 6 = (-110 + 16) dB
BCCH-FREQ-NCELL 6
: 5
Base station identity code of the 6'th neighbouring cellt = = 28
_____[ 40 ]___[ 11:52:51,488 ]___[ DOWN ]____[ SACCH ]______________________________
06 1e cd 3a 62 f2 10 31 04 55 08 2b 2b 2b 2b 2b 2b 2b 00 00 08 1c
06
0-------000-------0110
direction from
TransactionID
Protocol Discrim.
: originating site
: 0
: radio resource management messages
1e
00011110
MESSAGE TYPE
: SYSTEM INFORMATION TYPE 6
: Cell Identity
cd 11001101 Cell identity value1, Hex Wert
3a 00111010 Cell identity value2, Hex Wert
: Location Area Identification
62 ----0010 MCC digit 1
0110---- MCC digit 2
f2 ----0010 MCC digit 3
: 2
: 6
: 2
10
1111-------0000
0001----
MNC digit 3
MNC digit 1
MNC digit 2
: 15
: 0
: 1
31
04
00110001
00000100
Location area code (LAI), Number of MSC
Location area code (LAI), Number of BSC
: Cell Options (SACH)
55 0------- 1 spare bit
: 0
-1------ Power control indic.: is set
--01---- MSs shall use uplink discont.transmission
----0101 Radio Link Timeout : 24
: NCC Permitted
08 ----1--- BCCH carrier with NCC = 3 is permitted for monitoring;
_____[ 41 ]___[ 11:52:51,512 ]___[ UP ]___________________________________________
06 15 d4 13 69 9c 4b 49 05 d3 80 e9 a7 7c d2 b8 58 de
06
0-------000-------0110
direction from
TransactionID
Protocol Discrim.
: originating site
: 0
: radio resource management messages
15
00010101
MESSAGE TYPE
: MEASUREMENT REPORT
d4
1-------1-------010100
BA used
: yes
Discontinous Transmission was used
RXLEV-FULL-SERVING-CELL= (-110 + 20) dB
13
0-------0-------010011
0------110------100
110
spare
: 0
MEAS-VALID
: yes
RXLEV-SUB-SERVING-CELL = (-110 + 19) dB
spare
: 0
RX-QUAL-FULL-SERVING-CELL = ~9,05% error bit
RX-QUAL-SUB -SERVING-CELL = ~2,26% error bit
Number of neighbouring cell measurements = 6
011100
01001
011010
RXLEV-Neighbour-CELL 1 = (-110 + 28) dB
BCCH-FREQ-NCELL 1
: 9
Base station identity code of the 1'th neighbouring cell = 26
010010
00001
011101
RXLEV-Neighbour-CELL 2 = (-110 + 18) dB
BCCH-FREQ-NCELL 2
: 1
Base station identity code of the 2'th neighbouring cell= 29
001110
00000
011101
RXLEV-Neighbour-CELL 3 = (-110 + 14) dB
BCCH-FREQ-NCELL 3
: 0
Base station identity code of the 3'th neighbouring cell = 29
001101
00111
011111
RXLEV-Neighbour-CELL 4 = (-110 + 13) dB
BCCH-FREQ-NCELL 4
: 7
Base station identity code of the 4'th neighbouring cell = 31
001101
00101
011100
RXLEV-Neighbour-CELL 5 = (-110 + 13) dB
BCCH-FREQ-NCELL 5
: 5
Base station identity code of the 5'th neighbouring cell = 28
001011
00011
011110
RXLEV-Neighbour-CELL 6 = (-110 + 11) dB
BCCH-FREQ-NCELL 6
: 3
Base station identity code of the 6'th neighbouring cellt = = 30
_____[ 42 ]___[ 11:52:51,973 ]___[ DOWN ]____[ SACCH ]______________________________
06 1d 10 00 00 00 04 10 00 00 00 00 00 c0 82 9d 00 00
06
0-------000-------0110
direction from
TransactionID
Protocol Discrim.
: originating site
: 0
: radio resource management messages
1d
00011101
MESSAGE TYPE
: SYSTEM INFORMATION TYPE 5
10
00-------0-------1----
Format Type
: Bit Map 0 format
Extension Indicator : The IE carries the complete BA
BCCH allocation sequence number indication 1
04
10
-----1----1----
BCCH alloc. RF chan.: 91
BCCH alloc. RF chan.: 85
c0
82
9d
1-------1-----1------------11---------1-------1-------1--------1
BCCH
BCCH
BCCH
BCCH
BCCH
BCCH
BCCH
BCCH
BCCH
alloc.
alloc.
alloc.
alloc.
alloc.
alloc.
alloc.
alloc.
alloc.
RF
RF
RF
RF
RF
RF
RF
RF
RF
chan.:
chan.:
chan.:
chan.:
chan.:
chan.:
chan.:
chan.:
chan.:
40
39
32
26
24
21
20
19
17
_____[ 43 ]___[ 11:52:51,992 ]___[ UP ]___________________________________________
06 15 d1 10 37 a1 4b 47 0d e3 02 e8 e0 74 73 be 39 5c
06
0-------000-------0110
direction from
TransactionID
Protocol Discrim.
: originating site
: 0
: radio resource management messages
15
00010101
MESSAGE TYPE
: MEASUREMENT REPORT
d1
1-------1-------010001
BA used
: yes
Discontinous Transmission was used
RXLEV-FULL-SERVING-CELL= (-110 + 17) dB
10
0-------0-------010000
0------011------011
110
spare
: 0
MEAS-VALID
: yes
RXLEV-SUB-SERVING-CELL = (-110 + 16) dB
spare
: 0
RX-QUAL-FULL-SERVING-CELL = ~1,13% error bit
RX-QUAL-SUB -SERVING-CELL = ~1,13% error bit
Number of neighbouring cell measurements = 6
100001
01001
011010
RXLEV-Neighbour-CELL 1 = (-110 + 33) dB
BCCH-FREQ-NCELL 1
: 9
Base station identity code of the 1'th neighbouring cell = 26
001110
00011
011110
RXLEV-Neighbour-CELL 2 = (-110 + 14) dB
BCCH-FREQ-NCELL 2
: 3
Base station identity code of the 2'th neighbouring cell= 30
001100
00001
011101
RXLEV-Neighbour-CELL 3 = (-110 + 12) dB
BCCH-FREQ-NCELL 3
: 1
Base station identity code of the 3'th neighbouring cell = 29
000111
00000
011101
RXLEV-Neighbour-CELL 4 = (-110 + 7) dB
BCCH-FREQ-NCELL 4
: 0
Base station identity code of the 4'th neighbouring cell = 29
000111
00111
011111
RXLEV-Neighbour-CELL 5 = (-110 + 7) dB
BCCH-FREQ-NCELL 5
: 7
Base station identity code of the 5'th neighbouring cell = 31
000111
00101
011100
RXLEV-Neighbour-CELL 6 = (-110 + 7) dB
BCCH-FREQ-NCELL 6
: 5
Base station identity code of the 6'th neighbouring cellt = = 28
_____[ 44 ]___[ 11:52:52,453 ]___[ DOWN ]____[ SACCH ]______________________________
06 1e cd 3a 62 f2 10 31 04 55 08 2b 2b 2b 2b 2b 2b 2b 00 00 08 1c
06
0-------000-------0110
direction from
TransactionID
Protocol Discrim.
: originating site
: 0
: radio resource management messages
1e
00011110
MESSAGE TYPE
: SYSTEM INFORMATION TYPE 6
: Cell Identity
cd 11001101 Cell identity value1, Hex Wert
3a 00111010 Cell identity value2, Hex Wert
: Location Area Identification
62 ----0010 MCC digit 1
0110---- MCC digit 2
f2 ----0010 MCC digit 3
: 2
: 6
: 2
10
1111-------0000
0001----
MNC digit 3
MNC digit 1
MNC digit 2
: 15
: 0
: 1
31
04
00110001
00000100
Location area code (LAI), Number of MSC
Location area code (LAI), Number of BSC
: Cell Options (SACH)
55 0------- 1 spare bit
: 0
-1------ Power control indic.: is set
--01---- MSs shall use uplink discont.transmission
----0101 Radio Link Timeout : 24
: NCC Permitted
08 ----1--- BCCH carrier with NCC = 3 is permitted for monitoring;
_____[ 45 ]___[ 11:52:52,473 ]___[ UP ]___________________________________________
06 15 d5 17 31 a2 4b 49 0d e3 42 e9 05 70 70 3a 39 df
06
0-------000-------0110
direction from
TransactionID
Protocol Discrim.
: originating site
: 0
: radio resource management messages
15
00010101
MESSAGE TYPE
: MEASUREMENT REPORT
d5
1-------1-------010101
BA used
: yes
Discontinous Transmission was used
RXLEV-FULL-SERVING-CELL= (-110 + 21) dB
17
0-------0-------010111
0------011------000
110
spare
: 0
MEAS-VALID
: yes
RXLEV-SUB-SERVING-CELL = (-110 + 23) dB
spare
: 0
RX-QUAL-FULL-SERVING-CELL = ~1,13% error bit
RX-QUAL-SUB -SERVING-CELL = ~0,14% error bit
Number of neighbouring cell measurements = 6
100010
01001
011010
RXLEV-Neighbour-CELL 1 = (-110 + 34) dB
BCCH-FREQ-NCELL 1
: 9
Base station identity code of the 1'th neighbouring cell = 26
010010
00011
011110
RXLEV-Neighbour-CELL 2 = (-110 + 18) dB
BCCH-FREQ-NCELL 2
: 3
Base station identity code of the 2'th neighbouring cell= 30
001101
00001
011101
RXLEV-Neighbour-CELL 3 = (-110 + 13) dB
BCCH-FREQ-NCELL 3
: 1
Base station identity code of the 3'th neighbouring cell = 29
001000
00101
011100
RXLEV-Neighbour-CELL 4 = (-110 + 8) dB
BCCH-FREQ-NCELL 4
: 5
Base station identity code of the 4'th neighbouring cell = 28
000111
00000
011101
RXLEV-Neighbour-CELL 5 = (-110 + 7) dB
BCCH-FREQ-NCELL 5
: 0
Base station identity code of the 5'th neighbouring cell = 29
000111
00111
011111
RXLEV-Neighbour-CELL 6 = (-110 + 7) dB
BCCH-FREQ-NCELL 6
: 7
Base station identity code of the 6'th neighbouring cellt = = 31
_____[ 46 ]___[ 11:52:52,934 ]___[ DOWN ]____[ SACCH ]______________________________
06 1d 10 00 00 00 04 10 00 00 00 00 00 c0 82 9d 00 00
06
0-------000-------0110
direction from
TransactionID
Protocol Discrim.
: originating site
: 0
: radio resource management messages
1d
00011101
MESSAGE TYPE
: SYSTEM INFORMATION TYPE 5
10
00-------0-------1----
Format Type
: Bit Map 0 format
Extension Indicator : The IE carries the complete BA
BCCH allocation sequence number indication 1
04
10
c0
-----1----1---1-------1-----1------------11---------1-------1-------1--------1
BCCH
BCCH
BCCH
BCCH
BCCH
BCCH
BCCH
BCCH
BCCH
BCCH
BCCH
82
9d
alloc.
alloc.
alloc.
alloc.
alloc.
alloc.
alloc.
alloc.
alloc.
alloc.
alloc.
RF
RF
RF
RF
RF
RF
RF
RF
RF
RF
RF
chan.:
chan.:
chan.:
chan.:
chan.:
chan.:
chan.:
chan.:
chan.:
chan.:
chan.:
91
85
40
39
32
26
24
21
20
19
17
_____[ 47 ]___[ 11:52:52,953 ]___[ UP ]___________________________________________
06 15 d3 13 01 a7 4b 49 8d e2 82 e9 00 74 72 b8 21 df
06
0-------000-------0110
direction from
TransactionID
Protocol Discrim.
: originating site
: 0
: radio resource management messages
15
00010101
MESSAGE TYPE
: MEASUREMENT REPORT
d3
1-------1-------010011
BA used
: yes
Discontinous Transmission was used
RXLEV-FULL-SERVING-CELL= (-110 + 19) dB
13
0-------0-------010011
0------000------000
110
spare
: 0
MEAS-VALID
: yes
RXLEV-SUB-SERVING-CELL = (-110 + 19) dB
spare
: 0
RX-QUAL-FULL-SERVING-CELL = ~0,14% error bit
RX-QUAL-SUB -SERVING-CELL = ~0,14% error bit
Number of neighbouring cell measurements = 6
100111
01001
011010
RXLEV-Neighbour-CELL 1 = (-110 + 39) dB
BCCH-FREQ-NCELL 1
: 9
Base station identity code of the 1'th neighbouring cell = 26
010011
00011
011110
RXLEV-Neighbour-CELL 2 = (-110 + 19) dB
BCCH-FREQ-NCELL 2
: 3
Base station identity code of the 2'th neighbouring cell= 30
001010
RXLEV-Neighbour-CELL 3 = (-110 + 10) dB
00001
011101
BCCH-FREQ-NCELL 3
: 1
Base station identity code of the 3'th neighbouring cell = 29
001000
00000
011101
RXLEV-Neighbour-CELL 4 = (-110 + 8) dB
BCCH-FREQ-NCELL 4
: 0
Base station identity code of the 4'th neighbouring cell = 29
000111
00101
011100
RXLEV-Neighbour-CELL 5 = (-110 + 7) dB
BCCH-FREQ-NCELL 5
: 5
Base station identity code of the 5'th neighbouring cell = 28
000100
00111
011111
RXLEV-Neighbour-CELL 6 = (-110 + 4) dB
BCCH-FREQ-NCELL 6
: 7
Base station identity code of the 6'th neighbouring cellt = = 31
_____[ 48 ]___[ 11:52:53,371 ]___[ UP ]____[ SACCH ]______________________________
93 07
93
07
1-------001-------0011
00------
direction to
TransactionID
Protocol Discrim.
SendSequenceNumber
:
:
:
:
originating site
1
Call control and call related SS messages
0
--000111
MESSAGE TYPE
: CONNECT
_____[ 49 ]___[ 11:52:53,434 ]___[ DOWN ]____[ FACCH_F ]______________________________
06 1e cd 3a 62 f2 10 31 04 55 08 2b 2b 2b 2b 2b 2b 2b 00 00 08 1c
06
0-------000-------0110
direction from
TransactionID
Protocol Discrim.
: originating site
: 0
: radio resource management messages
1e
00011110
MESSAGE TYPE
: SYSTEM INFORMATION TYPE 6
: Cell Identity
cd 11001101 Cell identity value1, Hex Wert
3a 00111010 Cell identity value2, Hex Wert
: Location Area Identification
62 ----0010 MCC digit 1
0110---- MCC digit 2
f2 ----0010 MCC digit 3
: 2
: 6
: 2
10
1111-------0000
0001----
MNC digit 3
MNC digit 1
MNC digit 2
: 15
: 0
: 1
31
04
00110001
00000100
Location area code (LAI), Number of MSC
Location area code (LAI), Number of BSC
: Cell Options (SACH)
55 0------- 1 spare bit
: 0
-1------ Power control indic.: is set
--01---- MSs shall use uplink discont.transmission
----0101 Radio Link Timeout : 24
: NCC Permitted
08 ----1--- BCCH carrier with NCC = 3 is permitted for monitoring;
_____[ 50 ]___[ 11:52:53,434 ]___[ UP ]___________________________________________
06 15 d3 15 01 a4 4b 4a 8d e2 40 e9 21 74 73 be 39 5c
06
0-------000-------0110
direction from
TransactionID
Protocol Discrim.
: originating site
: 0
: radio resource management messages
15
00010101
MESSAGE TYPE
: MEASUREMENT REPORT
d3
1-------1-------010011
BA used
: yes
Discontinous Transmission was used
RXLEV-FULL-SERVING-CELL= (-110 + 19) dB
15
0-------0-------010101
0------000------000
110
spare
: 0
MEAS-VALID
: yes
RXLEV-SUB-SERVING-CELL = (-110 + 21) dB
spare
: 0
RX-QUAL-FULL-SERVING-CELL = ~0,14% error bit
RX-QUAL-SUB -SERVING-CELL = ~0,14% error bit
Number of neighbouring cell measurements = 6
100100
01001
011010
RXLEV-Neighbour-CELL 1 = (-110 + 36) dB
BCCH-FREQ-NCELL 1
: 9
Base station identity code of the 1'th neighbouring cell = 26
010101
00011
011110
RXLEV-Neighbour-CELL 2 = (-110 + 21) dB
BCCH-FREQ-NCELL 2
: 3
Base station identity code of the 2'th neighbouring cell= 30
001001
00000
011101
RXLEV-Neighbour-CELL 3 = (-110 + 9) dB
BCCH-FREQ-NCELL 3
: 0
Base station identity code of the 3'th neighbouring cell = 29
001001
00001
011101
RXLEV-Neighbour-CELL 4 = (-110 + 9) dB
BCCH-FREQ-NCELL 4
: 1
Base station identity code of the 4'th neighbouring cell = 29
000111
00111
011111
RXLEV-Neighbour-CELL 5 = (-110 + 7) dB
BCCH-FREQ-NCELL 5
: 7
Base station identity code of the 5'th neighbouring cell = 31
000111
00101
011100
RXLEV-Neighbour-CELL 6 = (-110 + 7) dB
BCCH-FREQ-NCELL 6
: 5
Base station identity code of the 6'th neighbouring cellt = = 28
_____[ 51 ]___[ 11:52:53,703 ]___[ DOWN ]____[ FACCH_F ]______________________________
13 0f
13
0f
0-------001-------0011
00------
direction from
TransactionID
Protocol Discrim.
SendSequenceNumber
:
:
:
:
originating site
1
Call control and call related SS messages
0
--001111
MESSAGE TYPE
:CONNECT ACKNOWLEDGE
_____[ 52 ]___[ 11:52:53,895 ]___[ DOWN ]____[ SACCH ]______________________________
06 1d 10 00 00 00 04 10 00 00 00 00 00 c0 82 9d 00 00
06
0-------000-------0110
direction from
TransactionID
Protocol Discrim.
: originating site
: 0
: radio resource management messages
1d
00011101
MESSAGE TYPE
: SYSTEM INFORMATION TYPE 5
10
00------
Format Type
: Bit Map 0 format
04
10
c0
82
9d
--0-------1----
Extension Indicator : The IE carries the complete BA
BCCH allocation sequence number indication 1
-----1----1---1-------1-----1------------11---------1-------1-------1--------1
BCCH
BCCH
BCCH
BCCH
BCCH
BCCH
BCCH
BCCH
BCCH
BCCH
BCCH
alloc.
alloc.
alloc.
alloc.
alloc.
alloc.
alloc.
alloc.
alloc.
alloc.
alloc.
RF
RF
RF
RF
RF
RF
RF
RF
RF
RF
RF
chan.:
chan.:
chan.:
chan.:
chan.:
chan.:
chan.:
chan.:
chan.:
chan.:
chan.:
91
85
40
39
32
26
24
21
20
19
17
_____[ 53 ]___[ 11:52:53,902 ]___[ UP ]___________________________________________
06 15 98 1a 01 a4 4b 4b 8d e3 82 e9 20 74 82 b8 39 df
06
0-------000-------0110
direction from
TransactionID
Protocol Discrim.
: originating site
: 0
: radio resource management messages
15
00010101
MESSAGE TYPE
: MEASUREMENT REPORT
98
1-------0-------011000
BA used
: yes
Discontinous Transmission was not used
RXLEV-FULL-SERVING-CELL= (-110 + 24) dB
1a
0-------0-------011010
0------000------000
110
spare
: 0
MEAS-VALID
: yes
RXLEV-SUB-SERVING-CELL = (-110 + 26) dB
spare
: 0
RX-QUAL-FULL-SERVING-CELL = ~0,14% error bit
RX-QUAL-SUB -SERVING-CELL = ~0,14% error bit
Number of neighbouring cell measurements = 6
100100
01001
011010
RXLEV-Neighbour-CELL 1 = (-110 + 36) dB
BCCH-FREQ-NCELL 1
: 9
Base station identity code of the 1'th neighbouring cell = 26
010111
00011
011110
RXLEV-Neighbour-CELL 2 = (-110 + 23) dB
BCCH-FREQ-NCELL 2
: 3
Base station identity code of the 2'th neighbouring cell= 30
001110
00001
011101
RXLEV-Neighbour-CELL 3 = (-110 + 14) dB
BCCH-FREQ-NCELL 3
: 1
Base station identity code of the 3'th neighbouring cell = 29
001001
00000
011101
RXLEV-Neighbour-CELL 4 = (-110 + 9) dB
BCCH-FREQ-NCELL 4
: 0
Base station identity code of the 4'th neighbouring cell = 29
001000
00101
011100
RXLEV-Neighbour-CELL 5 = (-110 + 8) dB
BCCH-FREQ-NCELL 5
: 5
Base station identity code of the 5'th neighbouring cell = 28
000111
00111
011111
RXLEV-Neighbour-CELL 6 = (-110 + 7) dB
BCCH-FREQ-NCELL 6
: 7
Base station identity code of the 6'th neighbouring cellt = = 31
_____[ 54 ]___[ 11:53:00,441 ]___[ DOWN ]____[ SACCH ]______________________________
06 1e cd 3a 62 f2 10 31 04 55 08 2b 2b 2b 2b 2b 2b 2b 00 00 08 1c
06
0-------000-------0110
direction from
TransactionID
Protocol Discrim.
: originating site
: 0
: radio resource management messages
1e
00011110
MESSAGE TYPE
: SYSTEM INFORMATION TYPE 6
: Cell Identity
cd 11001101 Cell identity value1, Hex Wert
3a 00111010 Cell identity value2, Hex Wert
: Location Area Identification
62 ----0010 MCC digit 1
0110---- MCC digit 2
f2 ----0010 MCC digit 3
: 2
: 6
: 2
10
1111-------0000
0001----
MNC digit 3
MNC digit 1
MNC digit 2
: 15
: 0
: 1
31
04
00110001
00000100
Location area code (LAI), Number of MSC
Location area code (LAI), Number of BSC
: Cell Options (SACH)
55 0------- 1 spare bit
: 0
-1------ Power control indic.: is set
--01---- MSs shall use uplink discont.transmission
----0101 Radio Link Timeout : 24
: NCC Permitted
08 ----1--- BCCH carrier with NCC = 3 is permitted for monitoring;
_____[ 55 ]___[ 11:53:00,449 ]___[ UP ]___________________________________________
06 15 96 14 01 a0 4b 47 8d e3 02 e8 e7 7c 72 b8 28 1d
06
0-------000-------0110
direction from
TransactionID
Protocol Discrim.
: originating site
: 0
: radio resource management messages
15
00010101
MESSAGE TYPE
: MEASUREMENT REPORT
96
1-------0-------010110
BA used
: yes
Discontinous Transmission was not used
RXLEV-FULL-SERVING-CELL= (-110 + 22) dB
14
0-------0-------010100
0------000------000
110
spare
: 0
MEAS-VALID
: yes
RXLEV-SUB-SERVING-CELL = (-110 + 20) dB
spare
: 0
RX-QUAL-FULL-SERVING-CELL = ~0,14% error bit
RX-QUAL-SUB -SERVING-CELL = ~0,14% error bit
Number of neighbouring cell measurements = 6
100000
01001
011010
RXLEV-Neighbour-CELL 1 = (-110 + 32) dB
BCCH-FREQ-NCELL 1
: 9
Base station identity code of the 1'th neighbouring cell = 26
001111
00011
011110
RXLEV-Neighbour-CELL 2 = (-110 + 15) dB
BCCH-FREQ-NCELL 2
: 3
Base station identity code of the 2'th neighbouring cell= 30
001100
00001
011101
RXLEV-Neighbour-CELL 3 = (-110 + 12) dB
BCCH-FREQ-NCELL 3
: 1
Base station identity code of the 3'th neighbouring cell = 29
000111
00111
011111
RXLEV-Neighbour-CELL 4 = (-110 + 7) dB
BCCH-FREQ-NCELL 4
: 7
Base station identity code of the 4'th neighbouring cell = 31
000111
00101
011100
RXLEV-Neighbour-CELL 5 = (-110 + 7) dB
BCCH-FREQ-NCELL 5
: 5
Base station identity code of the 5'th neighbouring cell = 28
000101
00000
011101
RXLEV-Neighbour-CELL 6 = (-110 + 5) dB
BCCH-FREQ-NCELL 6
: 0
Base station identity code of the 6'th neighbouring cellt = = 29
_____[ 56 ]___[ 11:53:00,922 ]___[ DOWN ]____[ SACCH ]______________________________
06 1d 10 00 00 00 04 10 00 00 00 00 00 c0 82 9d 00 00
06
0-------000-------0110
direction from
TransactionID
Protocol Discrim.
: originating site
: 0
: radio resource management messages
1d
00011101
MESSAGE TYPE
: SYSTEM INFORMATION TYPE 5
10
00-------0-------1----
Format Type
: Bit Map 0 format
Extension Indicator : The IE carries the complete BA
BCCH allocation sequence number indication 1
04
10
c0
-----1----1---1-------1-----1------------11---------1-------1-------1--------1
BCCH
BCCH
BCCH
BCCH
BCCH
BCCH
BCCH
BCCH
BCCH
BCCH
BCCH
82
9d
alloc.
alloc.
alloc.
alloc.
alloc.
alloc.
alloc.
alloc.
alloc.
alloc.
alloc.
RF
RF
RF
RF
RF
RF
RF
RF
RF
RF
RF
chan.:
chan.:
chan.:
chan.:
chan.:
chan.:
chan.:
chan.:
chan.:
chan.:
chan.:
91
85
40
39
32
26
24
21
20
19
17
_____[ 57 ]___[ 11:53:00,941 ]___[ UP ]___________________________________________
06 15 8f 0e 4b a2 4b 46 85 d2 4e f8 e3 78 60 3a 29 5c
06
0-------000-------0110
direction from
TransactionID
Protocol Discrim.
: originating site
: 0
: radio resource management messages
15
00010101
MESSAGE TYPE
: MEASUREMENT REPORT
8f
1-------0-------001111
BA used
: yes
Discontinous Transmission was not used
RXLEV-FULL-SERVING-CELL= (-110 + 15) dB
0e
0-------0-------001110
0------100------101
110
spare
: 0
MEAS-VALID
: yes
RXLEV-SUB-SERVING-CELL = (-110 + 14) dB
spare
: 0
RX-QUAL-FULL-SERVING-CELL = ~2,26% error bit
RX-QUAL-SUB -SERVING-CELL = ~4,53% error bit
Number of neighbouring cell measurements = 6
100010
01001
011010
RXLEV-Neighbour-CELL 1 = (-110 + 34) dB
BCCH-FREQ-NCELL 1
: 9
Base station identity code of the 1'th neighbouring cell = 26
001101
00001
011101
RXLEV-Neighbour-CELL 2 = (-110 + 13) dB
BCCH-FREQ-NCELL 2
: 1
Base station identity code of the 2'th neighbouring cell= 29
001001
00111
011111
RXLEV-Neighbour-CELL 3 = (-110 + 9) dB
BCCH-FREQ-NCELL 3
: 7
Base station identity code of the 3'th neighbouring cell = 31
000111
00011
011110
RXLEV-Neighbour-CELL 4 = (-110 + 7) dB
BCCH-FREQ-NCELL 4
: 3
Base station identity code of the 4'th neighbouring cell = 30
000110
00000
011101
RXLEV-Neighbour-CELL 5 = (-110 + 6) dB
BCCH-FREQ-NCELL 5
: 0
Base station identity code of the 5'th neighbouring cell = 29
000101
00101
011100
RXLEV-Neighbour-CELL 6 = (-110 + 5) dB
BCCH-FREQ-NCELL 6
: 5
Base station identity code of the 6'th neighbouring cellt = = 28
_____[ 58 ]___[ 11:53:01,402 ]___[ DOWN ]____[ SACCH ]______________________________
06 1e cd 3a 62 f2 10 31 04 55 08 2b 2b 2b 2b 2b 2b 2b 00 00 08 1c
06
0-------000-------0110
direction from
TransactionID
Protocol Discrim.
: originating site
: 0
: radio resource management messages
1e
00011110
MESSAGE TYPE
: SYSTEM INFORMATION TYPE 6
: Cell Identity
cd 11001101 Cell identity value1, Hex Wert
3a 00111010 Cell identity value2, Hex Wert
: Location Area Identification
62 ----0010 MCC digit 1
0110---- MCC digit 2
f2 ----0010 MCC digit 3
: 2
: 6
: 2
10
1111-------0000
0001----
MNC digit 3
MNC digit 1
MNC digit 2
: 15
: 0
: 1
31
04
00110001
00000100
Location area code (LAI), Number of MSC
Location area code (LAI), Number of BSC
: Cell Options (SACH)
55 0------- 1 spare bit
: 0
-1------ Power control indic.: is set
--01---- MSs shall use uplink discont.transmission
----0101 Radio Link Timeout : 24
: NCC Permitted
08 ----1--- BCCH carrier with NCC = 3 is permitted for monitoring;
_____[ 59 ]___[ 11:53:01,410 ]___[ UP ]___________________________________________
06 15 ce 0e 37 9e 4b 48 85 d2 80 e9 27 7c 81 bc 31 5c
06
0-------000-------0110
direction from
TransactionID
Protocol Discrim.
: originating site
: 0
: radio resource management messages
15
00010101
MESSAGE TYPE
: MEASUREMENT REPORT
ce
1-------1-------001110
BA used
: yes
Discontinous Transmission was used
RXLEV-FULL-SERVING-CELL= (-110 + 14) dB
0e
0-------0-------001110
0------011------011
110
spare
: 0
MEAS-VALID
: yes
RXLEV-SUB-SERVING-CELL = (-110 + 14) dB
spare
: 0
RX-QUAL-FULL-SERVING-CELL = ~1,13% error bit
RX-QUAL-SUB -SERVING-CELL = ~1,13% error bit
Number of neighbouring cell measurements = 6
011110
01001
011010
RXLEV-Neighbour-CELL 1 = (-110 + 30) dB
BCCH-FREQ-NCELL 1
: 9
Base station identity code of the 1'th neighbouring cell = 26
010001
00001
011101
RXLEV-Neighbour-CELL 2 = (-110 + 17) dB
BCCH-FREQ-NCELL 2
: 1
Base station identity code of the 2'th neighbouring cell= 29
001010
00000
011101
RXLEV-Neighbour-CELL 3 = (-110 + 10) dB
BCCH-FREQ-NCELL 3
: 0
Base station identity code of the 3'th neighbouring cell = 29
001001
00111
011111
RXLEV-Neighbour-CELL 4 = (-110 + 9) dB
BCCH-FREQ-NCELL 4
: 7
Base station identity code of the 4'th neighbouring cell = 31
001000
00011
011110
RXLEV-Neighbour-CELL 5 = (-110 + 8) dB
BCCH-FREQ-NCELL 5
: 3
Base station identity code of the 5'th neighbouring cell = 30
000110
00101
011100
RXLEV-Neighbour-CELL 6 = (-110 + 6) dB
BCCH-FREQ-NCELL 6
: 5
Base station identity code of the 6'th neighbouring cellt = = 28
_____[ 60 ]___[ 11:53:01,883 ]___[ DOWN ]____[ SACCH ]______________________________
06 1d 10 00 00 00 04 10 00 00 00 00 00 c0 82 9d 00 00
06
0-------000-------0110
direction from
TransactionID
Protocol Discrim.
: originating site
: 0
: radio resource management messages
1d
00011101
MESSAGE TYPE
: SYSTEM INFORMATION TYPE 5
10
00-------0-------1----
Format Type
: Bit Map 0 format
Extension Indicator : The IE carries the complete BA
BCCH allocation sequence number indication 1
04
10
c0
-----1----1---1-------1-----1------------11---------1-------1-------1--------1
BCCH
BCCH
BCCH
BCCH
BCCH
BCCH
BCCH
BCCH
BCCH
BCCH
BCCH
82
9d
alloc.
alloc.
alloc.
alloc.
alloc.
alloc.
alloc.
alloc.
alloc.
alloc.
alloc.
RF
RF
RF
RF
RF
RF
RF
RF
RF
RF
RF
chan.:
chan.:
chan.:
chan.:
chan.:
chan.:
chan.:
chan.:
chan.:
chan.:
chan.:
91
85
40
39
32
26
24
21
20
19
17
_____[ 61 ]___[ 11:53:01,891 ]___[ UP ]___________________________________________
06 15 8f 0f 37 9b 4b 47 85 d3 86 f1 40 74 93 be 31 5c
06
0-------000-------0110
direction from
TransactionID
Protocol Discrim.
: originating site
: 0
: radio resource management messages
15
00010101
MESSAGE TYPE
: MEASUREMENT REPORT
8f
1-------0-------001111
BA used
: yes
Discontinous Transmission was not used
RXLEV-FULL-SERVING-CELL= (-110 + 15) dB
0f
0-------0-------001111
0------011------011
110
spare
: 0
MEAS-VALID
: yes
RXLEV-SUB-SERVING-CELL = (-110 + 15) dB
spare
: 0
RX-QUAL-FULL-SERVING-CELL = ~1,13% error bit
RX-QUAL-SUB -SERVING-CELL = ~1,13% error bit
Number of neighbouring cell measurements = 6
011011
01001
011010
RXLEV-Neighbour-CELL 1 = (-110 + 27) dB
BCCH-FREQ-NCELL 1
: 9
Base station identity code of the 1'th neighbouring cell = 26
001111
00001
011101
RXLEV-Neighbour-CELL 2 = (-110 + 15) dB
BCCH-FREQ-NCELL 2
: 1
Base station identity code of the 2'th neighbouring cell= 29
001110
00011
011110
RXLEV-Neighbour-CELL 3 = (-110 + 14) dB
BCCH-FREQ-NCELL 3
: 3
Base station identity code of the 3'th neighbouring cell = 30
001010
00000
011101
RXLEV-Neighbour-CELL 4 = (-110 + 10) dB
BCCH-FREQ-NCELL 4
: 0
Base station identity code of the 4'th neighbouring cell = 29
001001
00111
011111
RXLEV-Neighbour-CELL 5 = (-110 + 9) dB
BCCH-FREQ-NCELL 5
: 7
Base station identity code of the 5'th neighbouring cell = 31
000110
00101
011100
RXLEV-Neighbour-CELL 6 = (-110 + 6) dB
BCCH-FREQ-NCELL 6
: 5
Base station identity code of the 6'th neighbouring cellt = = 28
_____[ 62 ]___[ 11:53:02,363 ]___[ DOWN ]____[ SACCH ]______________________________
06 1e cd 3a 62 f2 10 31 04 55 08 2b 2b 2b 2b 2b 2b 2b 00 00 08 1c
06
0-------000-------0110
direction from
TransactionID
Protocol Discrim.
: originating site
: 0
: radio resource management messages
1e
00011110
MESSAGE TYPE
: SYSTEM INFORMATION TYPE 6
: Cell Identity
cd 11001101 Cell identity value1, Hex Wert
3a 00111010 Cell identity value2, Hex Wert
: Location Area Identification
62 ----0010 MCC digit 1
0110---- MCC digit 2
f2 ----0010 MCC digit 3
1111----
MNC digit 3
: 2
: 6
: 2
: 15
10
----0000
0001----
MNC digit 1
MNC digit 2
: 0
: 1
31
04
00110001
00000100
Location area code (LAI), Number of MSC
Location area code (LAI), Number of BSC
: Cell Options (SACH)
55 0------- 1 spare bit
: 0
-1------ Power control indic.: is set
--01---- MSs shall use uplink discont.transmission
----0101 Radio Link Timeout : 24
: NCC Permitted
08 ----1--- BCCH carrier with NCC = 3 is permitted for monitoring;
_____[ 63 ]___[ 11:53:02,371 ]___[ UP ]___________________________________________
06 15 91 11 15 9b 4b 47 05 d2 c0 e9 63 78 a3 be 31 5c
06
0-------000-------0110
direction from
TransactionID
Protocol Discrim.
: originating site
: 0
: radio resource management messages
15
00010101
MESSAGE TYPE
: MEASUREMENT REPORT
91
1-------0-------010001
BA used
: yes
Discontinous Transmission was not used
RXLEV-FULL-SERVING-CELL= (-110 + 17) dB
11
0-------0-------010001
0------001------010
110
spare
: 0
MEAS-VALID
: yes
RXLEV-SUB-SERVING-CELL = (-110 + 17) dB
spare
: 0
RX-QUAL-FULL-SERVING-CELL = ~0,28% error bit
RX-QUAL-SUB -SERVING-CELL = ~0,57% error bit
Number of neighbouring cell measurements = 6
011011
01001
011010
RXLEV-Neighbour-CELL 1 = (-110 + 27) dB
BCCH-FREQ-NCELL 1
: 9
Base station identity code of the 1'th neighbouring cell = 26
001110
00001
011101
RXLEV-Neighbour-CELL 2 = (-110 + 14) dB
BCCH-FREQ-NCELL 2
: 1
Base station identity code of the 2'th neighbouring cell= 29
001011
00000
011101
RXLEV-Neighbour-CELL 3 = (-110 + 11) dB
BCCH-FREQ-NCELL 3
: 0
Base station identity code of the 3'th neighbouring cell = 29
001011
00011
011110
RXLEV-Neighbour-CELL 4 = (-110 + 11) dB
BCCH-FREQ-NCELL 4
: 3
Base station identity code of the 4'th neighbouring cell = 30
001010
00111
011111
RXLEV-Neighbour-CELL 5 = (-110 + 10) dB
BCCH-FREQ-NCELL 5
: 7
Base station identity code of the 5'th neighbouring cell = 31
000110
00101
011100
RXLEV-Neighbour-CELL 6 = (-110 + 6) dB
BCCH-FREQ-NCELL 6
: 5
Base station identity code of the 6'th neighbouring cellt = = 28
_____[ 64 ]___[ 11:53:02,844 ]___[ DOWN ]____[ SACCH ]______________________________
06 1d 10 00 00 00 04 10 00 00 00 00 00 c0 82 9d 00 00
06
0-------000-------0110
direction from
TransactionID
Protocol Discrim.
: originating site
: 0
: radio resource management messages
1d
00011101
MESSAGE TYPE
: SYSTEM INFORMATION TYPE 5
10
00-------0-------1----
Format Type
: Bit Map 0 format
Extension Indicator : The IE carries the complete BA
BCCH allocation sequence number indication 1
04
10
c0
-----1----1---1-------1-----1------------11---------1-------1-------1--------1
BCCH
BCCH
BCCH
BCCH
BCCH
BCCH
BCCH
BCCH
BCCH
BCCH
BCCH
82
9d
alloc.
alloc.
alloc.
alloc.
alloc.
alloc.
alloc.
alloc.
alloc.
alloc.
alloc.
RF
RF
RF
RF
RF
RF
RF
RF
RF
RF
RF
chan.:
chan.:
chan.:
chan.:
chan.:
chan.:
chan.:
chan.:
chan.:
chan.:
chan.:
91
85
40
39
32
26
24
21
20
19
17
_____[ 65 ]___[ 11:53:02,855 ]___[ UP ]___________________________________________
06 15 93 13 11 9f 4b 48 8d e3 c2 e9 60 74 b3 be 29 5c
06
0-------000-------0110
direction from
TransactionID
Protocol Discrim.
: originating site
: 0
: radio resource management messages
15
00010101
MESSAGE TYPE
: MEASUREMENT REPORT
93
1-------0-------010011
BA used
: yes
Discontinous Transmission was not used
RXLEV-FULL-SERVING-CELL= (-110 + 19) dB
13
0-------0-------010011
0------001------000
110
spare
: 0
MEAS-VALID
: yes
RXLEV-SUB-SERVING-CELL = (-110 + 19) dB
spare
: 0
RX-QUAL-FULL-SERVING-CELL = ~0,28% error bit
RX-QUAL-SUB -SERVING-CELL = ~0,14% error bit
Number of neighbouring cell measurements = 6
011111
01001
011010
RXLEV-Neighbour-CELL 1 = (-110 + 31) dB
BCCH-FREQ-NCELL 1
: 9
Base station identity code of the 1'th neighbouring cell = 26
010001
00011
011110
RXLEV-Neighbour-CELL 2 = (-110 + 17) dB
BCCH-FREQ-NCELL 2
: 3
Base station identity code of the 2'th neighbouring cell= 30
001111
00001
011101
RXLEV-Neighbour-CELL 3 = (-110 + 15) dB
BCCH-FREQ-NCELL 3
: 1
Base station identity code of the 3'th neighbouring cell = 29
001011
00000
011101
RXLEV-Neighbour-CELL 4 = (-110 + 11) dB
BCCH-FREQ-NCELL 4
: 0
Base station identity code of the 4'th neighbouring cell = 29
001011
00111
011111
RXLEV-Neighbour-CELL 5 = (-110 + 11) dB
BCCH-FREQ-NCELL 5
: 7
Base station identity code of the 5'th neighbouring cell = 31
000101
RXLEV-Neighbour-CELL 6 = (-110 + 5) dB
00101
011100
BCCH-FREQ-NCELL 6
: 5
Base station identity code of the 6'th neighbouring cellt = = 28
_____[ 66 ]___[ 11:53:03,324 ]___[ DOWN ]____[ SACCH ]______________________________
06 1e cd 3a 62 f2 10 31 04 55 08 2b 2b 2b 2b 2b 2b 2b 00 00 08 1c
06
0-------000-------0110
direction from
TransactionID
Protocol Discrim.
: originating site
: 0
: radio resource management messages
1e
00011110
MESSAGE TYPE
: SYSTEM INFORMATION TYPE 6
: Cell Identity
cd 11001101 Cell identity value1, Hex Wert
3a 00111010 Cell identity value2, Hex Wert
: Location Area Identification
62 ----0010 MCC digit 1
0110---- MCC digit 2
f2 ----0010 MCC digit 3
: 2
: 6
: 2
10
1111-------0000
0001----
MNC digit 3
MNC digit 1
MNC digit 2
: 15
: 0
: 1
31
04
00110001
00000100
Location area code (LAI), Number of MSC
Location area code (LAI), Number of BSC
: Cell Options (SACH)
55 0------- 1 spare bit
: 0
-1------ Power control indic.: is set
--01---- MSs shall use uplink discont.transmission
----0101 Radio Link Timeout : 24
: NCC Permitted
08 ----1--- BCCH carrier with NCC = 3 is permitted for monitoring;
_____[ 67 ]___[ 11:53:03,336 ]___[ UP ]___________________________________________
06 15 d3 13 01 a2 4b 4a 8d e4 42 e9 87 7c a0 3a 21 5c
06
0-------000-------0110
direction from
TransactionID
Protocol Discrim.
: originating site
: 0
: radio resource management messages
15
00010101
MESSAGE TYPE
: MEASUREMENT REPORT
d3
1-------1-------010011
BA used
: yes
Discontinous Transmission was used
RXLEV-FULL-SERVING-CELL= (-110 + 19) dB
13
0-------0-------010011
0------000------000
110
spare
: 0
MEAS-VALID
: yes
RXLEV-SUB-SERVING-CELL = (-110 + 19) dB
spare
: 0
RX-QUAL-FULL-SERVING-CELL = ~0,14% error bit
RX-QUAL-SUB -SERVING-CELL = ~0,14% error bit
Number of neighbouring cell measurements = 6
100010
01001
011010
RXLEV-Neighbour-CELL 1 = (-110 + 34) dB
BCCH-FREQ-NCELL 1
: 9
Base station identity code of the 1'th neighbouring cell = 26
010101
00011
011110
RXLEV-Neighbour-CELL 2 = (-110 + 21) dB
BCCH-FREQ-NCELL 2
: 3
Base station identity code of the 2'th neighbouring cell= 30
010001
00001
011101
RXLEV-Neighbour-CELL 3 = (-110 + 17) dB
BCCH-FREQ-NCELL 3
: 1
Base station identity code of the 3'th neighbouring cell = 29
001100
00111
011111
RXLEV-Neighbour-CELL 4 = (-110 + 12) dB
BCCH-FREQ-NCELL 4
: 7
Base station identity code of the 4'th neighbouring cell = 31
001010
00000
011101
RXLEV-Neighbour-CELL 5 = (-110 + 10) dB
BCCH-FREQ-NCELL 5
: 0
Base station identity code of the 5'th neighbouring cell = 29
000100
00101
011100
RXLEV-Neighbour-CELL 6 = (-110 + 4) dB
BCCH-FREQ-NCELL 6
: 5
Base station identity code of the 6'th neighbouring cellt = = 28
_____[ 68 ]___[ 11:53:03,664 ]___[ DOWN ]____[ FACCH_F ]______________________________
06 2b 1a 55 0e 40 62 0e 05
06
2b
0-------000-------0110
00101011
direction from
TransactionID
Protocol Discrim.
MESSAGE TYPE
:
:
:
:
: Celldescription
1a --011--- PLMN Colour Code NCC:
-----010 BS Colour code BCC :
00------ BCCH ARFCN high part:
55 01010101 BCCH ARFCN low part :
originating site
0
radio resource management messages
HANDOVER COMMAND
3
2
0
85
: Channel Description 2
0e 00001--- Channel type and TDMA offset = TCH/F + ACCHs
-----110 Timslot number
: 6
40
62
010-------000-------00
01100010
Training sequ. code :
Single channel
:
Sgl RF chan.high prt:
abs.RFchan. low part:
2
RF single channel
0
98
: Handover Reference
0e 00001110 Handover refer. val.: 14
: Power Command and Access Type
05 0------- Sending of Handover access is mandatory
-00----- spare
---00101 Power Level
: 5
_____[ 69 ]___[ 11:53:03,734 ]___[ UP ]____[ FACCH_F ]______________________________
06 2c 00
06
2c
0-------000-------0110
00101100
: RR Cause
00 00000000
direction from
TransactionID
Protocol Discrim.
MESSAGE TYPE
:
:
:
:
originating site
0
radio resource management messages
HANDOVER COMPLETE
Normal event
_____[ 70 ]___[ 11:53:03,773 ]___[ DOWN ]____[ FACCH_F ]______________________________
06 2d 00
06
2d
0-------000-------0110
00101101
direction from
TransactionID
Protocol Discrim.
MESSAGE TYPE
:
:
:
:
originating site
0
radio resource management messages
PHYSICAL INFORMATION
: Timing Advance
00 00------ spare
--000000 Timing advance value: 0 x 48/13 sec
_____[ 71 ]___[ 11:53:03,844 ]___[ DOWN ]____[ FACCH_F ]______________________________
06 2d 00
06
2d
0-------000-------0110
00101101
direction from
TransactionID
Protocol Discrim.
MESSAGE TYPE
:
:
:
:
originating site
0
radio resource management messages
PHYSICAL INFORMATION
: Timing Advance
00 00------ spare
--000000 Timing advance value: 0 x 48/13 sec
_____[ 72 ]___[ 11:53:04,137 ]___[ DOWN ]____[ SACCH ]______________________________
06 1d 10 00 00 00 00 00 00 00 00 00 00 c0 20 95 00 00
06
0-------000-------0110
direction from
TransactionID
Protocol Discrim.
: originating site
: 0
: radio resource management messages
1d
00011101
MESSAGE TYPE
: SYSTEM INFORMATION TYPE 5
10
00-------0-------1----
Format Type
: Bit Map 0 format
Extension Indicator : The IE carries the complete BA
BCCH allocation sequence number indication 1
c0
1-------1-------1----1---------1--------1--------1
BCCH
BCCH
BCCH
BCCH
BCCH
BCCH
BCCH
20
95
alloc.
alloc.
alloc.
alloc.
alloc.
alloc.
alloc.
RF
RF
RF
RF
RF
RF
RF
chan.:
chan.:
chan.:
chan.:
chan.:
chan.:
chan.:
40
39
30
24
21
19
17
_____[ 73 ]___[ 11:53:04,145 ]___[ UP ]___________________________________________
06 15 95 19 00 d5 0b a4 15 f1 84 f0 00 00 00 00 00 00
06
0-------000-------0110
direction from
TransactionID
Protocol Discrim.
: originating site
: 0
: radio resource management messages
15
00010101
MESSAGE TYPE
: MEASUREMENT REPORT
95
1-------0-------010101
BA used
: yes
Discontinous Transmission was not used
RXLEV-FULL-SERVING-CELL= (-110 + 21) dB
19
0-------0-------011001
0------
spare
: 0
MEAS-VALID
: yes
RXLEV-SUB-SERVING-CELL = (-110 + 25) dB
spare
: 0
-000------000
011
RX-QUAL-FULL-SERVING-CELL = ~0,14% error bit
RX-QUAL-SUB -SERVING-CELL = ~0,14% error bit
Number of neighbouring cell measurements = 3
010101
00001
011101
RXLEV-Neighbour-CELL 1 = (-110 + 21) dB
BCCH-FREQ-NCELL 1
: 1
Base station identity code of the 1'th neighbouring cell = 29
001000
00101
011111
RXLEV-Neighbour-CELL 2 = (-110 + 8) dB
BCCH-FREQ-NCELL 2
: 5
Base station identity code of the 2'th neighbouring cell= 31
000110
00010
011110
RXLEV-Neighbour-CELL 3 = (-110 + 6) dB
BCCH-FREQ-NCELL 3
: 2
Base station identity code of the 3'th neighbouring cell = 30
000000
00000
000000
RXLEV-Neighbour-CELL 4 = (-110 + 0) dB
BCCH-FREQ-NCELL 4
: 0
Base station identity code of the 4'th neighbouring cell = 0
000000
00000
000000
RXLEV-Neighbour-CELL 5 = (-110 + 0) dB
BCCH-FREQ-NCELL 5
: 0
Base station identity code of the 5'th neighbouring cell = 0
000000
00000
000000
RXLEV-Neighbour-CELL 6 = (-110 + 0) dB
BCCH-FREQ-NCELL 6
: 0
Base station identity code of the 6'th neighbouring cellt = = 0
_____[ 74 ]___[ 11:53:04,617 ]___[ DOWN ]____[ SACCH ]______________________________
06 1d 10 00 00 00 00 00 00 00 00 00 00 c0 20 95 00 00
06
0-------000-------0110
direction from
TransactionID
Protocol Discrim.
: originating site
: 0
: radio resource management messages
1d
00011101
MESSAGE TYPE
: SYSTEM INFORMATION TYPE 5
10
00-------0-------1----
Format Type
: Bit Map 0 format
Extension Indicator : The IE carries the complete BA
BCCH allocation sequence number indication 1
c0
1-------1-------1----1---------1--------1--------1
BCCH
BCCH
BCCH
BCCH
BCCH
BCCH
BCCH
20
95
alloc.
alloc.
alloc.
alloc.
alloc.
alloc.
alloc.
RF
RF
RF
RF
RF
RF
RF
chan.:
chan.:
chan.:
chan.:
chan.:
chan.:
chan.:
40
39
30
24
21
19
17
_____[ 75 ]___[ 11:53:04,625 ]___[ UP ]___________________________________________
06 15 de 1f 00 d5 0b a5 89 e2 0a f8 00 00 00 00 00 00
06
0-------000-------0110
direction from
TransactionID
Protocol Discrim.
: originating site
: 0
: radio resource management messages
15
00010101
MESSAGE TYPE
: MEASUREMENT REPORT
de
1-------1-------011110
BA used
: yes
Discontinous Transmission was used
RXLEV-FULL-SERVING-CELL= (-110 + 30) dB
1f
0-------
spare
: 0
-0-------011111
0------000------000
011
MEAS-VALID
: yes
RXLEV-SUB-SERVING-CELL = (-110 + 31) dB
spare
: 0
RX-QUAL-FULL-SERVING-CELL = ~0,14% error bit
RX-QUAL-SUB -SERVING-CELL = ~0,14% error bit
Number of neighbouring cell measurements = 3
010101
00001
011101
RXLEV-Neighbour-CELL 1 = (-110 + 21) dB
BCCH-FREQ-NCELL 1
: 1
Base station identity code of the 1'th neighbouring cell = 29
001011
00010
011110
RXLEV-Neighbour-CELL 2 = (-110 + 11) dB
BCCH-FREQ-NCELL 2
: 2
Base station identity code of the 2'th neighbouring cell= 30
001000
00101
011111
RXLEV-Neighbour-CELL 3 = (-110 + 8) dB
BCCH-FREQ-NCELL 3
: 5
Base station identity code of the 3'th neighbouring cell = 31
000000
00000
000000
RXLEV-Neighbour-CELL 4 = (-110 + 0) dB
BCCH-FREQ-NCELL 4
: 0
Base station identity code of the 4'th neighbouring cell = 0
000000
00000
000000
RXLEV-Neighbour-CELL 5 = (-110 + 0) dB
BCCH-FREQ-NCELL 5
: 0
Base station identity code of the 5'th neighbouring cell = 0
000000
00000
000000
RXLEV-Neighbour-CELL 6 = (-110 + 0) dB
BCCH-FREQ-NCELL 6
: 0
Base station identity code of the 6'th neighbouring cellt = = 0
_____[ 76 ]___[ 11:53:05,008 ]___[ DOWN ]____[ FACCH_F ]______________________________
13 25 02 e0 90
13
25
02
e0
90
0-------001-------0011
00------
direction from
TransactionID
Protocol Discrim.
SendSequenceNumber
:
:
:
:
originating site
1
Call control and call related SS messages
0
--100101
MESSAGE TYPE
: DISCONNECT
00000010
1-------11-------0-------0000
-0010000
LENGTH OF IE CAUSE
Extension Bit
Coding stand.
spare
location
cause
:
:
:
:
:
:
2
1
Standard defined for the GSM-PLMNS
0
user
Normal call clearing
_____[ 77 ]___[ 11:53:05,008 ]___[ UP ]___________________________________________
93 2d
93
2d
1-------001-------0011
00------
direction to
TransactionID
Protocol Discrim.
SendSequenceNumber
--101101
MESSAGE TYPE
:
:
:
:
originating site
1
Call control and call related SS messages
0
: RELEASE
_____[ 78 ]___[ 11:53:05,098 ]___[ DOWN ]____[ SACCH ]______________________________
06 1e aa b2 62 f2 10 31 04 55 08 2b 2b 2b 2b 2b 2b 2b 00 00 08 1a
06
0-------000-------0110
direction from
TransactionID
Protocol Discrim.
: originating site
: 0
: radio resource management messages
1e
00011110
MESSAGE TYPE
: SYSTEM INFORMATION TYPE 6
: Cell Identity
aa 10101010 Cell identity value1, Hex Wert
b2 10110010 Cell identity value2, Hex Wert
: Location Area Identification
62 ----0010 MCC digit 1
0110---- MCC digit 2
f2 ----0010 MCC digit 3
: 2
: 6
: 2
10
1111-------0000
0001----
MNC digit 3
MNC digit 1
MNC digit 2
: 15
: 0
: 1
31
04
00110001
00000100
Location area code (LAI), Number of MSC
Location area code (LAI), Number of BSC
: Cell Options (SACH)
55 0------- 1 spare bit
: 0
-1------ Power control indic.: is set
--01---- MSs shall use uplink discont.transmission
----0101 Radio Link Timeout : 24
: NCC Permitted
08 ----1--- BCCH carrier with NCC = 3 is permitted for monitoring;
_____[ 79 ]___[ 11:53:05,105 ]___[ UP ]___________________________________________
06 15 9f 1f 00 d4 0b a6 15 f2 c4 f0 00 00 00 00 00 00
06
0-------000-------0110
direction from
TransactionID
Protocol Discrim.
: originating site
: 0
: radio resource management messages
15
00010101
MESSAGE TYPE
: MEASUREMENT REPORT
9f
1-------0-------011111
BA used
: yes
Discontinous Transmission was not used
RXLEV-FULL-SERVING-CELL= (-110 + 31) dB
1f
0-------0-------011111
0------000------000
011
spare
: 0
MEAS-VALID
: yes
RXLEV-SUB-SERVING-CELL = (-110 + 31) dB
spare
: 0
RX-QUAL-FULL-SERVING-CELL = ~0,14% error bit
RX-QUAL-SUB -SERVING-CELL = ~0,14% error bit
Number of neighbouring cell measurements = 3
010100
00001
011101
RXLEV-Neighbour-CELL 1 = (-110 + 20) dB
BCCH-FREQ-NCELL 1
: 1
Base station identity code of the 1'th neighbouring cell = 29
001100
00101
011111
RXLEV-Neighbour-CELL 2 = (-110 + 12) dB
BCCH-FREQ-NCELL 2
: 5
Base station identity code of the 2'th neighbouring cell= 31
001011
00010
011110
RXLEV-Neighbour-CELL 3 = (-110 + 11) dB
BCCH-FREQ-NCELL 3
: 2
Base station identity code of the 3'th neighbouring cell = 30
000000
00000
000000
RXLEV-Neighbour-CELL 4 = (-110 + 0) dB
BCCH-FREQ-NCELL 4
: 0
Base station identity code of the 4'th neighbouring cell = 0
000000
00000
000000
RXLEV-Neighbour-CELL 5 = (-110 + 0) dB
BCCH-FREQ-NCELL 5
: 0
Base station identity code of the 5'th neighbouring cell = 0
000000
00000
000000
RXLEV-Neighbour-CELL 6 = (-110 + 0) dB
BCCH-FREQ-NCELL 6
: 0
Base station identity code of the 6'th neighbouring cellt = = 0
_____[ 80 ]___[ 11:53:05,328 ]___[ DOWN ]____[ FACCH_F ]______________________________
13 2a 08 02 e0 90
13
2a
08
02
e0
90
0-------001-------0011
00------
direction from
TransactionID
Protocol Discrim.
SendSequenceNumber
:
:
:
:
originating site
1
Call control and call related SS messages
0
--101010
MESSAGE TYPE
: RELEASE COMPLETE
00001000
00000010
1-------11-------0-------0000
-0010000
INFORMATION ELEMENT
LENGTH OF IE CAUSE
Extension Bit
Coding stand.
spare
location
cause
:
:
:
:
:
:
:
Cause
2
1
Standard defined for the GSM-PLMNS
0
user
Normal call clearing
_____[ 81 ]___[ 11:53:05,477 ]___[ DOWN ]____[ FACCH_F ]______________________________
06 0d 00
06
0-------000-------0110
direction from
TransactionID
Protocol Discrim.
: originating site
: 0
: radio resource management messages
0d
00001101
MESSAGE TYPE
: CHANNEL RELEASE
00
00000000
RR-Cause (reason of event) = Normal event
_____[ 82 ]___[ 11:53:05,578 ]___[ DOWN ]____[ SACCH ]______________________________
06 1d 10 00 00 00 00 00 00 00 00 00 00 c0 20 95 00 00
06
0-------000-------0110
direction from
TransactionID
Protocol Discrim.
: originating site
: 0
: radio resource management messages
1d
00011101
MESSAGE TYPE
: SYSTEM INFORMATION TYPE 5
10
00-------0-------1----
Format Type
: Bit Map 0 format
Extension Indicator : The IE carries the complete BA
BCCH allocation sequence number indication 1
c0
1-------1-------1----1---------1--------1--------1
BCCH
BCCH
BCCH
BCCH
BCCH
BCCH
BCCH
20
95
alloc.
alloc.
alloc.
alloc.
alloc.
alloc.
alloc.
RF
RF
RF
RF
RF
RF
RF
chan.:
chan.:
chan.:
chan.:
chan.:
chan.:
chan.:
40
39
30
24
21
19
17
_____[ 83 ]___[ 11:53:05,738 ]___[ UP ]____[ FACCH_F ]______________________________
06 15 98 15 00 d4 0b a6 09 e2 8a f8 00 00 00 00 00 00
06
0-------000-------0110
direction from
TransactionID
Protocol Discrim.
: originating site
: 0
: radio resource management messages
15
00010101
MESSAGE TYPE
: MEASUREMENT REPORT
98
1-------0-------011000
BA used
: yes
Discontinous Transmission was not used
RXLEV-FULL-SERVING-CELL= (-110 + 24) dB
15
0-------0-------010101
0------000------000
011
spare
: 0
MEAS-VALID
: yes
RXLEV-SUB-SERVING-CELL = (-110 + 21) dB
spare
: 0
RX-QUAL-FULL-SERVING-CELL = ~0,14% error bit
RX-QUAL-SUB -SERVING-CELL = ~0,14% error bit
Number of neighbouring cell measurements = 3
010100
00001
011101
RXLEV-Neighbour-CELL 1 = (-110 + 20) dB
BCCH-FREQ-NCELL 1
: 1
Base station identity code of the 1'th neighbouring cell = 29
001100
00010
011110
RXLEV-Neighbour-CELL 2 = (-110 + 12) dB
BCCH-FREQ-NCELL 2
: 2
Base station identity code of the 2'th neighbouring cell= 30
001010
00101
011111
RXLEV-Neighbour-CELL 3 = (-110 + 10) dB
BCCH-FREQ-NCELL 3
: 5
Base station identity code of the 3'th neighbouring cell = 31
000000
00000
000000
RXLEV-Neighbour-CELL 4 = (-110 + 0) dB
BCCH-FREQ-NCELL 4
: 0
Base station identity code of the 4'th neighbouring cell = 0
000000
00000
000000
RXLEV-Neighbour-CELL 5 = (-110 + 0) dB
BCCH-FREQ-NCELL 5
: 0
Base station identity code of the 5'th neighbouring cell = 0
000000
00000
000000
RXLEV-Neighbour-CELL 6 = (-110 + 0) dB
BCCH-FREQ-NCELL 6
: 0
Base station identity code of the 6'th neighbouring cellt = = 0
_____[ 84 ]___[ 11:53:06,398 ]___[ DOWN ]____[ BCCH ]______________________________
06 1b aa b2 62 f2 10 31 04 40 04 3c 55 65 08 a5 00 00 3c 2b 2b 2b
06
0-------000-------0110
direction from
TransactionID
Protocol Discrim.
: originating site
: 0
: radio resource management messages
1b
00011011
MESSAGE TYPE
: SYSTEM INFORMATION TYPE 3
: Cell Identity
aa 10101010 Cell identity value1: Hex-Wert verwenden
b2 10110010 Cell identity value2: Hex-Wert verwenden
: Location Area Identification
62 ----0010 Mobile CC digit 1
0110---- Mobile CC digit 2
f2 ----0010 Mobile CC digit 3
: 2
: 6
: 2
10
1111-------0000
0001----
Mobile NC digit 3
Mobile NC digit 1
Mobile NC digit 2
: 15
: 0
: 1
31
04
00110001
00000100
Loc. area code (LAC) = ID of MSC (hex)
Loc. area code (LAC) = ID of BSC (hex)
: Control Channel Description
40 0------- 1 spare bit
: 0
-1------ MSs in the cell shall apply IMSI attach and detach procedure
--000--- Number of blocks
: 0 reserved for access grant
-----000 1 basic physical channel used for CCCH not combined with SDCCHs
04
00000--- spare bits
: 5
-----100 6 multi frames period for transmission PAGING REQUEST messages to the
same paging subgroup
3c
00111100
T3212 TimeOut value : 60 deci hours
: Cell Options BCCH,
55 0------- 1 spare bit
: 0
-1------ PWRC Power control indicator is set
--01---- MSs shall use uplink discontinous transmission
----0101 Radio Link Timeout : 24
: Cell Selection Parameters;
65 011----- Cell Resel. Hyster. : 6 dB RXLEV hysteresis for level average (LA) reselection
---00101 Max Tx power level : Mobile may use 5
08 0------- Addition. Reselect Param ind: in SI4 rest octets, i.p., and SI7 and SI8
rest octets, ...
-0------ New establishment cause is not supported
--001000 RXLEV ACCESS MIN
: -110 +8 db permitted
: RACH Control Parameters
a5 10------ Max. of retransm.
: 4
--1001-- used to spread TX
: 12 slots
------0- The cell is barred : no
-------1 Call reestablishment in cell is not allowed
00
-----0-00000--------00
Emergency Call EC10 : allowed
Acc.contr.cl. 11-15 : 0/1 access permitted/forbidden
Acc.contr.cl.
8-9 : 0/1 access permitted/forbidden
00
00000000
Acc.contr.cl.
0-7 : 0/1 access permitted/forbidden
: SI 3 Restoktett
0 Selection Parameters not present
0 Power Offset not present
1 System Information 2ter Indicator not present
1 Early Classmark Sending Control present
1 Scheduling if and where not present
1 High: GPRS indicator = present
: RA COLOUR
000 Routing Area colour = 0
: SI13 Position
0 SYSTEM INFORMATION TYPE 13 message is sent on BCCH Norm;
10101100 spare bits
: End SI 3 Restoktett
_____[ 85 ]___[ 11:53:06,629 ]___[ DOWN ]____[ BCCH ]______________________________
06 1c 62 f2 10 31 04 65 08 a5 00 00 01 2b 2b 2b 2b 2b 2b 2b 2b 2b
06
0-------000-------0110
direction from
TransactionID
Protocol Discrim.
: originating site
: 0
: radio resource management messages
1c
00011100
MESSAGE TYPE
: SYSTEM INFORMATION TYPE 4
: Location Area Identification
62 ----0010 Mobile CC digit 1
0110---- Mobile CC digit 2
f2 ----0010 Mobile CC digit 3
: 2
: 6
: 2
10
1111-------0000
0001----
Mobile NC digit 3
Mobile NC digit 1
Mobile NC digit 2
: 15
: 0
: 1
31
04
00110001
00000100
Loc. area code (LAI), ID of MSC (hex)
Loc. area code (LAI), ID of BSC (hex)
: Cell Selection Parameters
65 011----- Cell Reselect Hyst. : 6 dB RXLEV hyst. For LA re-select
---00101 Max Tx power level : MS may use 5
08
0-------0-------001000
No Additional cells in SysInfo 7-8
New establishm.cause: not supported
RXLEV ACCESS MIN permitted = -110+8dB
: RACH Control Parameters
a5 10------ Max. of retransmissions
--1001-- 12 slots used to spread TX
------0- The cell is barred : no
-------1 Call reestab.in cell: not allowed
00
-----0-00000--forbidden
------00
forbidden
00 00000000
forbidden
Emergency Call EC 10: allowed
Acc. ctrl class11-15: bit pattern,0 = access permitted, 1 = access
Acc. ctrl class 8-9 : bit pattern,0 = access permitted, 1 = access
Acc. ctrl class 0-7 : bit pattern,0 = access permitted, 1 = access
: SI4 Rest Octets
: SI4 Rest Octets_O
: Optional selection parameters
0 Selection Parameters = not present
: End Optional selection parameters
: Optional Power offset
0 Power Offset = not present
: End Optional Power offset
: GPRS Indicator
0 High: GPRS indicator = present
: RA COLOUR
000 Routing Area colour = 0
: SI13 Position
0 SYSTEM INFORMATION TYPE 13 message is sent on BCCH Norm;
: End GPRS Indicator
: End SI4 Rest Octets_O
: Break Indicator
1 High Additional parameters, "SI4 Rest Octets_S" are sent in SYSTEM
INFORMATION TYPE 7 and 8
: End SI4 Restoctet
_____[ 86 ]___[ 11:53:07,379 ]___[ DOWN ]____[ PCH ]______________________________
06 21 00 01 00 2b 2b 2b 2b 2b 2b 2b 2b 2b 2b 2b 2b 2b 2b 2b 2b 2b
06
0-------000-------0110
direction from
TransactionID
Protocol Discrim.
: originating site
: 0
: radio resource management messages
21
00100001
MESSAGE TYPE
: PAGING REQUEST TYPE 1
00
----00-------00
--00---00------
spare bits
Page Mode
Channel Needed
Channel Needed
:
:
:
:
0
Normal paging
(first) Any Channel
(second) Any Channel
: Mobile Identity 1
01 00000001 length of Mob.ident.:
00 0000---- Identity Digit 1
:
----0--- No. of ID digits
:
-----000 Type of identity
:
1
hex value = f, if
even
No Identity
TMSI/P-TMSI
_____[ 87 ]___[ 11:53:07,801 ]___[ DOWN ]____[ BCCH ]______________________________
06 19 00 00 00 02 00 10 00 00 00 00 00 00 00 00 00 00 a5 00 00 2b
06
0-------000-------0110
direction from
TransactionID
Protocol Discrim.
19
00011001
MESSAGE TYPE
: originating site
: 0
: radio resource management messages
: SYSTEM INFORMATION TYPE 1
: Cell Channel Description
00 00------ Format Type
--00---- 2 spare bits
: Bit Map 0 format
: 0
02
10
: ARFCN 98
: ARFCN 85
------1---1----
Cell Allocation
Cell Allocation
: RACH Control Parameters
a5 10------ Max. of retransmiss
--1001-- slots to spread TX
------0- The cell is barred
-------1 Call reestabl.i.cell
:
:
:
:
4
12
no
not allowed
00
00000-------0-------00
Acc. contr. cl. 11-15: Bitmuster: 0 Zugr.erl.,1 Zugr.n.erl.
Emergency Call EC 10 : allowed
Acc. contr. cl. 8-9 : Bitmuster: 0 Zugr.erl.,1 Zugr.n.erl.
00
00000000
Acc. contr. cl. 0-7
: Bitmuster: 0 Zugr.erl.,1 Zugr.n.erl.
: NCH Position
0 no NCH Position
0101011 spare padding
_____[ 88 ]___[ 11:53:08,152 ]___[ DOWN ]____[ BCCH ]______________________________
06 1a 00 00 00 00 00 10 00 00 00 00 00 c0 20 95 00 00 08 a5 00 00
06
0-------000-------0110
direction from
TransactionID
Protocol Discrim.
: originating site
: 0
: radio resource management messages
1a
00011010
MESSAGHE TYPE
: SYSTEM INFORMATION TYPE 2
00
--0-------0----
Extension Indicator : The IE carries the complete BA
BCCH alloc. sequ.num: 0
10
---1----
BCCH alloc. RF chan.: 85
c0
1-------1-------1----1---------1--------1--------1
BCCH
BCCH
BCCH
BCCH
BCCH
BCCH
BCCH
08
----1---
BCCH carrier with NCC = 3 is permitted for monitoring;
a5
10-------1001-------0-------1
Max. of retransmiss.: 4
12 slots used to spread TX
The cell is barred : no
Call reestablishment in cell is not allowed
00
-----0-00000--------00
Emergency Call EC 10: allowed
acc ctrl class 11-15: 0/1 access permitted/forbidden
acc ctrl class 8-9 : 0/1 access permitted/forbidden
00
00000000
acc ctrl class
20
95
alloc.
alloc.
alloc.
alloc.
alloc.
alloc.
alloc.
RF
RF
RF
RF
RF
RF
RF
chan.:
chan.:
chan.:
chan.:
chan.:
chan.:
chan.:
40
39
30
24
21
19
17
0-7 : 0/1 access permitted/forbidden
_____[ 89 ]___[ 11:53:08,754 ]___[ DOWN ]____[ BCCH ]______________________________
06 00 f0 00 58 58 67 ca 10 80 51 80 ab 2b 2b 2b 2b 2b 2b 2b 2b 2b
06
0-------000-------0110
direction from
TransactionID
Protocol Discrim.
: originating site
: 0
: radio resource management messages
00
00000000
MESSAGE TYPE
: SYSTEM INFORMATION TYPE 13
1-------111-------0000
SI 13 Restoctet
BCCH_CHANGE_MARK
SI_CHANGE_FIELD
: present
: 7
: Update of unspecified SI messages
0
switch SI13_CHANGE_MARK and GPRS Mobile Allocation = not present
0 PBCCH not present in Cell
00000001 RAC (Routing Area Code) = 1
0 SPGC_CCCH_SUP
: SPLIT_PG_CYCLE not supported on CCCH
: Priority access
110 packet access is allowed for priority level 1 to 4;
: Network Control Order
00 NETWORK_CONTR. ORDER: MS controlled cell re-selection, no measurement
reporting.
: GPRS CELL OPTIONS IE
01
011
000-------011-------0-------0
1111
1
001
010
000
NMO Network Mode of Operation II : No PPCH available, no Gs If
T3168
: (3+1)x500 ms
T3192
: 500msec
DRXTIMER_MAX
ACCESS_BURST_TYPE
: Use 8 bit access burst
default format is four access bursts
BS_CV_MAX
: Countdown Value = 15
PAN description = present
PAN_DEC
PAN_INC
PAN_MAX
: Max value for counter N3102= 5
: End GPRS Cell Options
: GPRS Power Control Param structure
1000
ALPHA
= 8 x 0,1
01000 T_AVG_W = 8
00000 T_AVG_T = 0
1 PC_MEAS_CHAN
: Downlink Measurement shall be made on PDCH
0100 N_AVG_I
: 2 exp (4/2)
: End GPRS Power Control Param structure
0110000
spare padding
: 0
_____[ 90 ]___[ 11:53:08,953 ]___[ DOWN ]____[ BCCH ]______________________________
06 1a 00 00 00 00 00 10 00 00 00 00 00 c0 20 95 00 00 08 a5 00 00
06
0-------000-------0110
direction from
TransactionID
Protocol Discrim.
: originating site
: 0
: radio resource management messages
1a
00011010
MESSAGHE TYPE
: SYSTEM INFORMATION TYPE 2
00
--0-------0----
Extension Indicator : The IE carries the complete BA
BCCH alloc. sequ.num: 0
10
c0
20
95
---1---1-------1-------1----1---------1--------1--------1
BCCH
BCCH
BCCH
BCCH
BCCH
BCCH
BCCH
BCCH
08
----1---
BCCH carrier with NCC = 3 is permitted for monitoring;
a5
10-------1001-------0-------1
Max. of retransmiss.: 4
12 slots used to spread TX
The cell is barred : no
Call reestablishment in cell is not allowed
00
-----0-00000--------00
Emergency Call EC 10: allowed
acc ctrl class 11-15: 0/1 access permitted/forbidden
acc ctrl class 8-9 : 0/1 access permitted/forbidden
00
00000000
acc ctrl class
alloc.
alloc.
alloc.
alloc.
alloc.
alloc.
alloc.
alloc.
RF
RF
RF
RF
RF
RF
RF
RF
chan.:
chan.:
chan.:
chan.:
chan.:
chan.:
chan.:
chan.:
85
40
39
30
24
21
19
17
0-7 : 0/1 access permitted/forbidden
_____[ 91 ]___[ 11:53:09,215 ]___[ DOWN ]____[ BCCH ]______________________________
06 1b aa b2 62 f2 10 31 04 40 04 3c 55 65 08 a5 00 00 3c 2b 2b 2b
06
0-------000-------0110
direction from
TransactionID
Protocol Discrim.
: originating site
: 0
: radio resource management messages
1b
00011011
MESSAGE TYPE
: SYSTEM INFORMATION TYPE 3
: Cell Identity
aa 10101010 Cell identity value1: Hex-Wert verwenden
b2 10110010 Cell identity value2: Hex-Wert verwenden
: Location Area Identification
62 ----0010 Mobile CC digit 1
0110---- Mobile CC digit 2
f2 ----0010 Mobile CC digit 3
10
1111-------0000
0001----
Mobile NC digit 3
Mobile NC digit 1
Mobile NC digit 2
: 2
: 6
: 2
: 15
: 0
: 1
31
04
00110001
00000100
Loc. area code (LAC) = ID of MSC (hex)
Loc. area code (LAC) = ID of BSC (hex)
: Control Channel Description
40 0------- 1 spare bit
: 0
-1------ MSs in the cell shall apply IMSI attach and detach procedure
--000--- Number of blocks
: 0 reserved for access grant
-----000 1 basic physical channel used for CCCH not combined with SDCCHs
04
00000--- spare bits
: 5
-----100 6 multi frames period for transmission PAGING REQUEST messages to the
same paging subgroup
3c
00111100
T3212 TimeOut value : 60 deci hours
: Cell Options BCCH,
55 0------- 1 spare bit
: 0
-1------ PWRC Power control indicator is set
--01---- MSs shall use uplink discontinous transmission
----0101 Radio Link Timeout : 24
: Cell Selection Parameters;
65 011----- Cell Resel. Hyster. : 6 dB RXLEV hysteresis for level average (LA) reselection
---00101 Max Tx power level : Mobile may use 5
08 0------- Addition. Reselect Param ind: in SI4 rest octets, i.p., and SI7 and SI8
rest octets, ...
-0------ New establishment cause is not supported
--001000 RXLEV ACCESS MIN
: -110 +8 db permitted
: RACH Control Parameters
a5 10------ Max. of retransm.
: 4
--1001-- used to spread TX
: 12 slots
------0- The cell is barred : no
-------1 Call reestablishment in cell is not allowed
00
-----0-00000--------00
Emergency Call EC10 : allowed
Acc.contr.cl. 11-15 : 0/1 access permitted/forbidden
Acc.contr.cl.
8-9 : 0/1 access permitted/forbidden
00
00000000
Acc.contr.cl.
0-7 : 0/1 access permitted/forbidden
: SI 3 Restoktett
0 Selection Parameters not present
0 Power Offset not present
1 System Information 2ter Indicator not present
1 Early Classmark Sending Control present
1 Scheduling if and where not present
1 High: GPRS indicator = present
: RA COLOUR
000 Routing Area colour = 0
: SI13 Position
0 SYSTEM INFORMATION TYPE 13 message is sent on BCCH Norm;
10101100 spare bits
: End SI 3 Restoktett
_____[ 92 ]___[ 11:53:10,945 ]___[ DOWN ]____[ BCCH ]______________________________
06 1b cd 3a 62 f2 10 31 04 40 04 3c 55 65 08 a5 00 00 3c 2b 2b 2b
06
0-------000-------0110
direction from
TransactionID
Protocol Discrim.
: originating site
: 0
: radio resource management messages
1b
00011011
MESSAGE TYPE
: SYSTEM INFORMATION TYPE 3
: Cell Identity
cd 11001101 Cell identity value1: Hex-Wert verwenden
3a 00111010 Cell identity value2: Hex-Wert verwenden
: Location Area Identification
62 ----0010 Mobile CC digit 1
0110---- Mobile CC digit 2
f2 ----0010 Mobile CC digit 3
: 2
: 6
: 2
10
1111-------0000
0001----
Mobile NC digit 3
Mobile NC digit 1
Mobile NC digit 2
: 15
: 0
: 1
31
04
00110001
00000100
Loc. area code (LAC) = ID of MSC (hex)
Loc. area code (LAC) = ID of BSC (hex)
: Control Channel Description
40 0------- 1 spare bit
: 0
-1------ MSs in the cell shall apply IMSI attach and detach procedure
--000--- Number of blocks
: 0 reserved for access grant
-----000 1 basic physical channel used for CCCH not combined with SDCCHs
04
00000--- spare bits
: 5
-----100 6 multi frames period for transmission PAGING REQUEST messages to the
same paging subgroup
3c
00111100
T3212 TimeOut value : 60 deci hours
: Cell Options BCCH,
55 0------- 1 spare bit
: 0
-1------ PWRC Power control indicator is set
--01---- MSs shall use uplink discontinous transmission
----0101 Radio Link Timeout : 24
: Cell Selection Parameters;
65 011----- Cell Resel. Hyster. : 6 dB RXLEV hysteresis for level average (LA) reselection
---00101 Max Tx power level : Mobile may use 5
08 0------- Addition. Reselect Param ind: in SI4 rest octets, i.p., and SI7 and SI8
rest octets, ...
-0------ New establishment cause is not supported
--001000 RXLEV ACCESS MIN
: -110 +8 db permitted
: RACH Control Parameters
a5 10------ Max. of retransm.
: 4
--1001-- used to spread TX
: 12 slots
------0- The cell is barred : no
-------1 Call reestablishment in cell is not allowed
00
-----0-00000--------00
Emergency Call EC10 : allowed
Acc.contr.cl. 11-15 : 0/1 access permitted/forbidden
Acc.contr.cl.
8-9 : 0/1 access permitted/forbidden
00
00000000
Acc.contr.cl.
0-7 : 0/1 access permitted/forbidden
: SI 3 Restoktett
0 Selection Parameters not present
0 Power Offset not present
1 System Information 2ter Indicator not present
1 Early Classmark Sending Control present
1 Scheduling if and where not present
1 High: GPRS indicator = present
: RA COLOUR
000 Routing Area colour = 0
: SI13 Position
0 SYSTEM INFORMATION TYPE 13 message is sent on BCCH Norm;
10101100 spare bits
: End SI 3 Restoktett