Limit Comparison
Date Completed: ___5/5/2013______________
Performed By: ____Sam Remp______________
Specifications Tested
Engr.
Spec. #
Unit of
Measure
Specification (description)
The program developed must be
able to log and compare input data
to a standard.
6.1
Marginal
Value
+/-0.2,
V/µs
+/-0.05
Revision History
Revision
1
Description
Date
Document created
Equipment
__X__ Fully assembled test fixture (with motors and tooth phantoms)
__X__ Arduino Uno board and EasyDrivers
__X__ Front Panel GUI
__X__ DPR35E Pulser/Receiver Unit
__X__ 10 MHz Ultrasound Transducer
__X__ Tektronix TDS2012C Oscilloscope
Sections


Part I Data collection
Part II Data comparison
Comments/Status
Standard is based on
whether the delta taken of
any two input data
matches, and the
tolerances to which they
match.
Limit Comparison
Date Completed: ___5/5/2013______________
Performed By: ____Sam Remp______________
Part I Data collection
__X__ 1. Ensure that the DPR35E unit is properly connected.
__X__ 2. Ensure that the test fixture is properly assembled with all five motors.
__X__ 3. Connect the motors to the proper pins on the EasyDrivers and Arduino Uno.
__X__ 4. Ensure that the Arduino Uno has been configured for Labview integration, following the
instructions shown in Configuring Test Station.
__X__ 5. Turn on the DPR35E unit and Tektronix TDS2012C oscilloscope.
__X__ 6. Open the following file from SVN: //source code/DPR35/front panel.vi
__X__ 7. Ensure that the VISA resource name reflects the appropriate COM port.
__X__ 8. Place a drop of coupling agent on the tooth phantom to be tested.
__X__ 9. Flip the switch on the front panel VI to “ON” and run the program.
__X__ 10. Export and save sampled data to a dedicated folder.
__X__ 11. Repeat steps 9 to 11 for other teeth.
Summarize data below
Tooth Socket
0
Data Collection
(Pass/Fail)
Successfully
able to
determine
materials and
log data to
file?
PASS
Sign off on section completion before continuing:______________________________
Limit Comparison
Date Completed: ___5/5/2013______________
Performed By: ____Sam Remp______________
Part II Data comparison
__X__ 1. Record the number of the tooth socket being tested.
__X__ 2. Ensure that the DPR35E unit is properly connected.
__X__ 3. Ensure that the test fixture is properly assembled with all five motors.
__X__ 4. Connect the motors to the proper pins on the EasyDrivers and Arduino Uno.
__X__ 5. Ensure that the Arduino Uno has been configured for Labview integration, following the
instructions shown in Configuring Test Station.
__X__ 6. Turn on the DPR35E unit and Tektronix TDS2012C oscilloscope.
__X__ 7. Open the following file from SVN:
__X__ 8. Ensure that the VISA resource name reflects the appropriate COM port.
__X__ 9. Place a drop of coupling agent on the tooth phantom to be tested.
__X__ 10. Flip the switch on the front panel VI to “ON” and run the program.
__X__ 11. Export and save sampled data to a dedicated folder.
__X__ 12. Repeat steps 9 to 11 for one more test.
__X__ 13. Compare data obtained and determine if within comparison tolerances.
__X__ 14. Repeat steps 9 to 13 for other teeth.
Summarize data below
Tooth Socket
0
35 Test Runs
Data Comparison
(Successfully Identifies
Materials)
Success Each Time
Sign off on section completion before continuing:______________________________