The 20 th
International Drying Symposium (IDS 2016)
Gifu, JAPAN, 7-10 August 2015
1*
2
1 Environmental and Renewable Energy Systems, Gifu University
1-1 Yanagido, Gifu city, Gifu, Japan, 501-1193
Tel.:+81-58-123-4567, E-mail: xxx@yyy.com
2 Department, Institute
Address, City, ZIP Code, Country
Tel.:+country code area number telephone number, E-mail: xxx@yyy.zzz
Keywords : provide 5 keywords here
INTRODUCTION
Please use this template for your abstract preparation.
The guideline should be followed to ensure uniformity throughout the paragraph. Please submit your abstract via email (secretariat@ids2016.org).
Please take care to have the title below the figure (not in the next column).
Tables: Tables can be inserted into the text with separate numbering as follows in Table 1. The title of the table is left justified, 12 pt spacing before and 6 pt after. For the second line hanging indentation of
1.25 cm is used. After the figure, there is 1 single empty line of 6 pt, with no spacing before and after.
BODY TEXT
The paper body is organized into sections. The first one is always the INTRODUCTION. The section headings are not numbered, TNR 10 pt, normal, 12 pt spacing before, centered in separate line.
Text: TNR 10 pt, normal, single line, 6 pt spacing before the paragraph, justified.
Table 1. Title of the table
Activity
Abstract submission
Deadline
10 March 2016
Final notification of abstract acceptance
30 April 2016
Secondary headings
It is possible to use secondary headings, TNR, 10 pt, not numbered, left justified and italic.
The maximum length of the paper is 2 pages. Page settings: size A4, 3 cm top, 2.5 cm bottom, left and right margins, two columns (0.8 cm between them).
Equations are centered and numbered consecutively starting from 1 as follows:

C
 t

D r

C
 r
.

 2
C (1)
D
 r
2
Before and after the equation, there is 1 single empty line of 12 pt, with no spacing before and after.
The text should be in US-English.
Fig. 1. Title of the figure
Figures: Please use good quality figures. The figures have to be numbered and centered (see Fig. 1) with 6 pt spacing before and a centered title below each of them, which itself has 6 pt spacing before and after.
CITATIONS IN THE TEXT
Where a publication is referred to in the text, enclose the name of author(s) and the year of publication within brackets: (Mujumdar, 1990). For two authors give both names and the year: (Farkas and Rendik,
1997). For three or more authors give the name of the first author plus
 et al.

, and the year: (Seres et al.,
2004). If giving a list of references, separate them using semi-colons.
Put only the year in brackets, when directly referring to the author(s) of the publication. For example:


This theory was extended by Farkas and Rendik
(1997), as … 
.
CONCLUSIONS
The paper will not be reformatted. a x
NOMENCLATURE specific surface area length co-ordinate
Greek letters

 heat transfer coefficient residence time
Subscripts i e o inlet equilibrium origin m 2 m m -3
Wm s
-2 K -1
ACKNOWLEDGEMENTS
Write acknowledgements here if you wish. Keep it short and simple.
REFERENCES
The list of references must be arranged alphabetically according to the first author, subsequent lines indented 5 mm. Do not number references.
Publications of the same author(s) should be listed in order of the year of the publication. In case of more than one publication for the same author in the same year, label them by a, b, c, etc. and year (2006a).
Please note that all references listed here must be directly cited in the text body.
Author(s) of the book (Year), Title of book, (Name of editor(s)), Publisher, Place of publication.
Author(s) of journal publication (Year), Title of paper, Name of journal, Volume, page numbers.
Author(s) of conference presentation (Year), Title of paper, Title of conference proceedings, Place of conference, Date of conference, Volume, page numbers.
Mujumdar, A.S. (1990), Handbook of industrial drying, 2nd edition, Marcel Dekker, New York.
Farkas, I. (2003), Control aspects of postharvest technologies, Chapter No 29 of Handbook of postharvest technology /ed. Chakraverty, A., A.S.
Mujumdar, G.S.V. Raghavan and H.S.
Ramaswamy/, Marcel Dekker Inc., New York-
Basel, 2003, pp. 845-866.
Itaya, Y. N. Kobayashi, L. Li, A. Suami, M. Sawai and H. Hamabe (2015), Drying of sewage sludge during composting in an updraft dryer with the concept of using self-energy generated within the system, Drying Technology, Vol. 33, pp. 1029-
1038.
Kobayashi N., H. Hamabe, Y. Li and Y. Itaya (2014),
Sludge treatment system combined with biodrying and carbonization, Proceedings of 19 th
International Drying Symposium, Rion, France,
August 11-15, 2014, Vol. A, pp. 932-940.