LIGHTING
SPECIFICATIONS
TELESCOPING TRIPOD LIGHT – 500 WATT
R•O•M Corporation
6800 E 163rd St
Belton MO 64012
800-827-3692
KR-SB-805
An R-O-M Corporation tripod telescoping light pole, part number KR-SB-805, comprised of the following components shall be supplied.
One (1) R-O-M Stonco, model KR-05 light shall be supplied. The rectangular die cast light fixture shall measure 8-1/4" wide by 10-3/4"
high by 5-1/2" deep and have a white powder coat finish. The 500 watt 130 volt light shall have a T-3 quartz halogen bulb with a field
replaceable modular, 10" high by 8" wide anodized aluminum reflector and molded, high heat polycarbonate handle. The fixture shall
have a locking swivel joint with a 3/4" diameter NPT threaded base to allow the light to be manually tilted up/down and locked in position
by the operator. The light fixture will include an on/off switch located near the swivel knuckle.
The wiring shall be routed from the light head, down the inside of the inner pole and out the bottom of the outer pole. The e nd of the cord
shall be coiled and ready to accept an electrical plug.
The R-O-M 800 series tripod shall have legs and poles constructed of 6063-T6 extruded aluminum with a 320 grit spiral brushed and
anodized finish. The tripod shall have a full-sized handle for carrying, as well as to assist with opening and closing, and an over-sized
locking knob to keep the device in the desired position.
The legs shall have a diameter of 3-3/4" when closed. The 1/3 round, 120 degree arc shaped legs neatly fold into a cylindrical shape
when closed. A 1/4 turn locking knob secures the legs in the open and closed position. The 50" outer pole will be 1-7/8" x .060" extruded
aluminum 6063-T6 with 320 spiral grit finish. The 40" inner tube will be made of the same material, but will be 1-3/8" x .060. The poles
shall have a brite dip anodized finish.
The inner tube shall recess into the outer tube and be locked in any position by a two piece locking collar machined from 6061-T6
aluminum. The locking collar assembly consists of a threaded locking cap that compresses an injection molded delrin compression
sleeve. This locking collar assembly will provide a water-tight seal for the inner and outer pole. The locking collar assembly shall have a
brite dip anodized finish and lifetime warranty. Collars and main hinges shall be constructed from die-cast aluminum alloy painted with
durable two-coat silver powder paint, or alloy 6063-T6 with brite-dip anodized finish. Brackets and hardware shall be fabricated from 300
series polished stainless steel.
TELESCOPING TRIPOD LIGHT - 500 WATT - TRUCK MOUNT
KR-SB-805-TM
An R-O-M Corporation tripod telescoping light pole, part number KR-SB-805-TM, comprised of the following components shall be
supplied.
One (1) R-O-M Stonco, model KR-05 light shall be supplied. The rectangular die cast light fixture shall measure 8-1/4" wide by 10-3/4"
high by 5-1/2" deep and have a white powder coat finish. The 500 watt 130 volt light shall have a T-3 quartz halogen bulb with a field
replaceable modular, 10" high by 8" wide anodized aluminum reflector and molded, high heat polycarbonate handle. The fixture shall
have a locking swivel joint with a 3/4" diameter NPT threaded base to allow the light to be manually tilted up/down and locked in position
by the operator. The light fixture will include an on/off switch located near the swivel knuckle. The wiring shall be routed from the light
head, down the inside of the inner pole and out the bottom of the outer pole. The end of the cord shall be coiled and ready to accept an
electrical plug.
The R-O-M 800 series tripod shall have legs and poles constructed of 6063-T6 extruded aluminum with a 320 grit spiral brushed and
anodized finish. The tripod shall have a full-sized handle for carrying, as well as to assist with opening and closing, and an over-sized
locking knob to keep the device in the desired position.
The legs shall have a diameter of 3-3/4" when closed. The 1/3 round, 120 degree arc shaped legs neatly fold into a cylindrical shape
when closed. A 1/4 turn locking knob secures the legs in the open and closed position. The 50" outer pole will be 1-7/8" x .060" extruded
aluminum 6063-T6 with 320 spiral grit finish. The 40" inner tube will be made of the same material, but will be 1-3/8" x .060. The poles
shall have a brite dip anodized finish.
The inner tube shall recess into the outer tube and be locked in any position by a two piece locking collar machined from 6061-T6
aluminum. The locking collar assembly consists of a threaded locking cap that compresses an injection molded delrin compression
sleeve. This locking collar assembly will provide a water-tight seal for the inner and outer pole. The locking collar assembly shall have a
brite dip anodized finish and lifetime warranty. Collars and main hinges shall be constructed from die-cast aluminum alloy painted with
durable two-coat silver powder paint, or alloy 6063-T6 with brite-dip anodized finish. Brackets and hardware shall be fabricated from 300
series polished stainless steel.
Copyright 2012 R•O•M Corporation All Rights Reserved.
[1]
FM-7.2-5396 / Rev A / 06-01-2012
LIGHTING
SPECIFICATIONS
R•O•M Corporation
6800 E 163rd St
Belton MO 64012
800-827-3692
A truck mounting bracket kit for attachment of the tripod to an external vehicle surface shall be supplied. This kit shall consist of a die cast
aluminum lower bracket that shall mount to the vehicle and cradle the bottom of the folding legs. A rubber insulator shall be utilized to
prevent any movement or rattles. A three piece upper bracket assembly machined from 6061-T6 aluminum and have a brite dip anodized
finish shall also be supplied. This three piece bracket design will consist of a clamp style saddle with removable retaining cap that fits
around the upper portion of the outer pole. This saddle will incorporate a tongue that will fit into a receiver that is mounted to the vehicle.
The saddle will then be secured to the receiver with a cam action pull to release lever to allow quick removal of the tripod light from the
vehicle.
TELESCOPING TRIPOD LIGHT - 500 WATT - TRUCK MOUNT
KR-SB-805-TM-7
An R-O-M Corporation tripod telescoping light pole, part number KR-SB-805-TM-7, comprised of the following components shall be
supplied.
One (1) R-O-M Stonco, model KR-05 light shall be supplied. The rectangular die cast light fixture shall measure 8-1/4" wide by 10-3/4"
high by 5-1/2" deep and have a white powder coat finish. The 500 watt 130 volt light shall have a T-3 quartz halogen bulb with a field
replaceable modular, 10" high by 8" wide anodized aluminum reflector and molded, high heat polycarbonate handle. The fixture shall
have a locking swivel joint with a 3/4" diameter NPT threaded base to allow the light to be manually tilted up/down and locked in position
by the operator. The light fixture will include an on/off switch located near the swivel knuckle. The wiring shall be routed from the light
head, down the inside of the inner pole and out the bottom of the outer pole. The end of the cord shall be coiled and ready to accept an
electrical plug.
The R-O-M 800 series tripod shall have legs and poles constructed of 6063-T6 extruded aluminum with a 320 grit spiral brushed and
anodized finish. The tripod shall have a full-sized handle for carrying, as well as to assist with opening and closing, and an over-sized
locking knob to keep the device in the desired position.
The legs shall have a diameter of 3-3/4" when closed. The 1/3 round, 120 degree arc shaped legs neatly fold into a cylindrical shape
when closed. A 1/4 turn locking knob secures the legs in the open and closed position. The 50" outer pole will be 1-7/8" x .060" extruded
aluminum 6063-T6 with 320 spiral grit finish. The 40" inner tube will be made of the same material, but will be 1-3/8" x .060. The poles
shall have a brite dip anodized finish.
The inner tube shall recess into the outer tube and be locked in any position by a two piece locking collar machined from 6061-T6
aluminum. The locking collar assembly consists of a threaded locking cap that compresses an injection molded delrin compression
sleeve. This locking collar assembly will provide a water-tight seal for the inner and outer pole. The locking collar assembly shall have a
brite dip anodized finish and lifetime warranty. Collars and main hinges shall be constructed from die-cast aluminum alloy painted with
durable two-coat silver powder paint, or alloy 6063-T6 with brite-dip anodized finish. Brackets and hardware shall be fabricated from 300
series polished stainless steel.
A truck mounting bracket kit for 7" offset attachment of the tripod to an external vehicle surface shall be supplied. This kit shall consist of
a die cast aluminum lower bracket that shall mount to the vehicle and cradle the bottom of the folding legs. A rubber insulator shall be
utilized to prevent any movement or rattles. A three piece upper bracket assembly machined from 6061-T6 aluminum and have a brite dip
anodized finish shall also be supplied. This three piece bracket design will consist of a clamp style saddle with removable retaining cap
that fits around the upper portion of the outer pole. This saddle will incorporate a tongue that will fit into a receiver that is mounted to the
vehicle. The saddle will then be secured to the receiver with a cam action pull to release lever to allow quick removal of the tripod light
from the vehicle.
TELESCOPING TRIPOD LIGHT - 500 WATT - TRUCK MOUNT with INDICATOR
KR-SB-805-TM-I
An R-O-M Corporation tripod telescoping light pole, part number KR-SB-805-TM-I, comprised of the following components shall be
supplied.
One (1) R-O-M Stonco, model KR-05 light shall be supplied. The rectangular die cast light fixture shall measure 8-1/4" wide by 10-3/4"
high by 5-1/2" deep and have a white powder coat finish. The 500 watt 130 volt light shall have a T-3 quartz halogen bulb with a field
replaceable modular, 10" high by 8" wide anodized aluminum reflector and molded, high heat polycarbonate handle. The fixture shall
have a locking swivel joint with a 3/4" diameter NPT threaded base to allow the light to be manually tilted up/down and locked in position
by the operator. The light fixture will include an on/off switch located near the swivel knuckle. The wiring shall be routed from the light
head, down the inside of the inner pole and out the bottom of the outer pole. The end of the cord shall be coiled and ready to accept an
electrical plug.
Copyright 2012 R•O•M Corporation All Rights Reserved.
[2]
FM-7.2-5396 / Rev A / 06-01-2012
LIGHTING
SPECIFICATIONS
R•O•M Corporation
6800 E 163rd St
Belton MO 64012
800-827-3692
An indicator switch to alert the operator of a raised light pole shall be supplied. The switch shall be comprised of a 1/4 amp magnetic reed
switch attached to the outer pole activated by a magnet attached to the inner pole when the pole is left in the up position.
The R-O-M 800 series tripod shall have legs and poles constructed of 6063-T6 extruded aluminum with a 320 grit spiral brushed and
anodized finish. The tripod shall have a full-sized handle for carrying, as well as to assist with opening and closing, and an over-sized
locking knob to keep the device in the desired position.
The legs shall have a diameter of 3-3/4" when closed. The 1/3 round, 120 degree arc shaped legs neatly fold into a cylindrical shape
when closed. A 1/4 turn locking knob secures the legs in the open and closed position. The 50" outer pole will be 1-7/8" x .060" extruded
aluminum 6063-T6 with 320 spiral grit finish. The 40" inner tube will be made of the same material, but will be 1-3/8" x .060. The poles
shall have a brite dip anodized finish.
The inner tube shall recess into the outer tube and be locked in any position by a two piece locking collar machined from 6061-T6
aluminum. The locking collar assembly consists of a threaded locking cap that compresses an injection molded delrin compression
sleeve. This locking collar assembly will provide a water-tight seal for the inner and outer pole. The locking collar assembly shall have a
brite dip anodized finish and lifetime warranty. Collars and main hinges shall be constructed from die-cast aluminum alloy painted with
durable two-coat silver powder paint, or alloy 6063-T6 with brite-dip anodized finish. Brackets and hardware shall be fabricated from 300
series polished stainless steel.
A truck mounting bracket kit for attachment of the tripod to an external vehicle surface shall be supplied. This kit shall consist of a die cast
aluminum lower bracket that shall mount to the vehicle and cradle the bottom of the folding legs. A rubber insulator shall be utilized to
prevent any movement or rattles. A three piece upper bracket assembly machined from 6061-T6 aluminum and have a brite dip anodized
finish shall also be supplied. This three piece bracket design will consist of a clamp style saddle with removable retaining cap that fits
around the upper portion of the outer pole. This saddle will incorporate a tongue that will fit into a receiver that is mounted to the vehicle.
The saddle will then be secured to the receiver with a cam action pull to release lever to allow quick removal of the tripod light from the
vehicle.
Copyright 2012 R•O•M Corporation All Rights Reserved.
[3]
FM-7.2-5396 / Rev A / 06-01-2012