CURRICULAM VITAE
Name: Jossy Mathew
Address:
Puliyamthottiyil(h)
Pakalomattom p.o
Kuravilangad(via)
Kottayam
Kerala
Pin: 686642
Mobile: 0091 9895208793.
Ph: Home: 0091 4822233804 .
E-MAIL-id: jossymathew53@yahoo.com
CAREER SEEKING:INSTRUMENTATION AND CONTROL ENGINEER.
Career Summary:
More than 5 years (1 Year gulf)experience as an Instrumentation Engineer in petrochemical
plants and Power sector in the field of Engineering, Inspection and trouble shooting of field
instruments . The experience is enriched as an Instrument Engineer in various field, including Field
Construction, Calibration of Instruments, loop checking, Pre-commissioning, , Industrial
Automation and Process control including PLC, installation and commissioning of field
instrumentation like Control Valve flow meters , Level & Flow instruments, Gas Analyzers and
Trouble shooting . Prepare and review documents like Tender evaluation, Procurement order,
Job procedures, Method Statement, ITP, QCP for compliance of the concerned codes and
standards, also looking after additional requirements as per specification, sequence of activities,
erection scheme etc.
Technical Certification:
 Bachelor of Technology in ELECTRONICS & COMMUNICATION from M.G University ,
Kottayam , Kerala, India with 68% marks.
 Diploma in electronics from Govt polytechnic Kottayam,kerala,india with 77% marks.
 Advanced Diploma in Process Control Instrumentation from SIIT, Thalayolaparambu ,
Kottayam, Kerala.
TECHNICAL SKILLS:
 Experienced in Field calibration, Bench calibration, Loop checking, Trouble
shooting, Cable termination, Instrument tubing, Conducting, Cable tagging, leak
testing, Installation of field instruments, Pre-commissioning, Commissioning, Cable
pulling and cable route and trench plan, radio communication, telemetry and RTU
DCS, SCADA ,PERMIT TO WORK SYSTEM,RFI.
 PLC System knowledge (Siemens, Schneider). Familiarity with SCADA system (Win CC) .
 Process Engineering - PFD, P&ID, and HAZOP (Hazardous Operation Analysis).
 Control Engineering - System Design, Specification, FAT, SAT, Configuration,
Implementation, logic Development.
 Instruments - Selection, Sizing, Specifications of Control valves, Safety valves ,Transmitter
Sensors.
 Computer & Networking - Microsoft office (Word, Excel, Power Point, Project, Access),
Microsoft Windows OS (9x, NT, 2000, Xp), LAN Architecture & Technology (Ethernet,
TCP/IP, Token Ring, Field bus, Mod bus).
 QA/QC Activities - ITP, Method Statement, QCP for compliance of the Concerned Codes
and standards.
I am having good knowledge in System Design, Engineering, Software Development, Logic
development, PLC (Allen Bradley, Siemens, and Triconex).
.
Work Experience: (GULF)
GAMA QATAR CO.W.L.L, QATAR
( For Qatar gas QCS Project under main contractor CTJV(Chiyoda
Technip Joint Venture).
Designation: Instrument and control Engineer.
Term: July 2009 to JUNE 2010.
Duties & Responsibilities:








My Responsibilities is to provide advice on applicable standard to the project team &
contractor.
Prepare documents of ITP, Method Statement, QCP for compliance of the Concerned
Codes and standards.
Audit inspection record and ensure the compilation and traceability of all the documents
related to a system.
Inspection and witness of Instruments and control system and to ensure that equipment,
materials are inspected on arrival at site and prior to final closure as appropriate.
Installation of transmitters according to hookup drawings, location drawings and
P&ID.
Tubing of differential pressure level transmitters, pressure transmitters, flow
transmitters.
Responsible for installing Marshalling, System, VMS, FGS, Pakscan cabinets &
installation of field instrument junction box.
Experienced in Field calibration, Bench calibration, Loop checking, Trouble
shooting, Cable termination, Tube bending, Conducting, Valve stroking, Cable
tagging, leak testing, Installation of field instruments, Pre-commissioning,
Commissioning, Cable pulling and cable route and trench plan.



Supervised and ensured the instrument & analyzer system construction teams are
aware of their responsibilities and delicate nature of working with critical and
sophisticated analyzers.
Successfully completed loop verification and functional testing of instrument &
analyzer systems, cause & effect interlocks & testing of F&G controls systems
related to analyzer systems.
Monitoring of correct installation of Field Instrument & also finding the actual
location & guiding proper termination with the help of drawings such as Piping &
Instrument Diagram (P&ID), Instrument Loop Diagram (ILD, Hookup drawing etc.
Extensive knowledge in sensors , electronic circuits , A/ D convertors
microprocessors, RF communication, signals and systems, serial RS 232 , RS 422 RS
485 hardware protocols, TCP/ IP network protocol.
 EUROCON INSTRUMENTS PVT.LTD,CHENNAI
Designation: INSTRUMENT AND CONTROL ENGINEER.
Department: E & I (OIL & GAS INDUSTRY)
Term: From July 2007 to july2009.
Duties & Responsibilities:
 My responsibilities is Project Design and Detailed Engineering including preparing
Data sheets, BOQ Specification, Layout, JB schedule, Loop Diagram, Hook up
diagram, Electrical Interface, Logic Development, System Design, Configuration,
Implementation.
 Keep track of P&ID, hook- ups, and loop-wiring diagrams, signal flow diagrams.
 Responsible for Cabling activity, including Instrument cable Termination, IR and
Continuity checking, Calibration of instruments, Loop checking, logic checking
,Pre-commissioning & Commissioning activities of Instruments. System Study and
Configuration System. Testing and Installation and Field Instruments. Installation
of system cables. Mod bus cable, Serial link cable and Ethernet cable.

As-built drawing for cables cross-section, Hook-up drawings, P & ID
drawings for Instrument installation and Instrument cable termination.
Installation of various field Instruments, such as Installation of cable tray,
Installation of process instruments, Installation of junction boxes,
Installation of foundation field bus junction boxes, laying of cables, from
junction box to instrument and JB to instruments. Glandig & Termination
for various instruments.
 HI-TECH ENGINEERING ,COCHIN.
Designation: INSTRUMENT ENGINEER.
Department: E&I ( OIL & GAS Industry)
Term: From August 2002 to JUNE 2004.
Duties & Responsibilities:.



Responsible for handling commissioning activities like Calibration, Loop checking
& trouble shooting of pressure, level flow, temperature transmitters & switch (highlow), valves, control valves & ON/OFF valves & meggering of cables i.e field bus &
conventional.
Checking of P & I diagrams, Hook up drawing, reviewing of instrument data sheets,, and
preparation of instrument index, installation details, location plans & layouts, cable
schedules, connection lists, cable routing, loop drawings, Logic diagram, Cause & Effect
diagrams, bill of materials.
Handled to Carry out planned maintenance activities for Instruments, Final Control
Element. Process Control Instruments, Transmitters, Control Valves, On-Off valves.
Handled trouble shoot for Instruments. Handled plant emergencies related to Instrument
system and rectification Worked independently in rotating shift as and when required by
Company for Maintenance of Instrument systems.
Handled calibration of instrument, Maintenance of Instruments and work according to
Permit Systems in the Plant. To update the log books after completion of jobs and update
other records as required by supervisors.
Worked on all Preventive and Shutdown Maintenance of Instrument.
Major field instruments handled:
 Flow Meters: Mass flow (Rosemount and Forbes Marshall), Vortex (Yokogawa), Magnetic
meter (Yokogawa and Forbes Marshall), Transmitters: Rosemount (Smart), Foxboro
intelligent Transmitter, Honeywell, Gas Analyzers.
 Control Valves: Fisher (U.K.), Arca (Germany & India)
Test equipments handled:
 Dead weight tester (DH Budenberg 580 series)
 Druck calibrator (DPI 610 Pressure calibrator, Druck limited).
Personal Profile:
Name
:
Jossy Mathew
Age
:
26years
Date of Birth
:
25-05-1984
Sex
:
Male.
Nationality
:
Indian
Marital Status
:
Single
Passport Details
Place of issue
Date of issue
Date of expiry
Current CTC
Expected CTC
Notice period
:
:
:
:
:
:
:
E4856162.
cochin
25-03-2003
24-03-2013
1200 USD
1400 USD (Negotiable)
10 days.
Contact Details:
Puliyamthottiyil(h)
Pakalomattom p.o
Kuravilangad(via)
Kottayam
Kerala
India
Pin: 686642
Phone: 0091 9895208793.
Declaration:
I am confident that I can get well served with the work of your esteemed organization. At
erliest if an opportunity if offered to serve as your need. I can execute my work to the
entire satisfaction of the company.
Place : kottayam
Date : 08-09-2010
Jossy mathew