SKILLS FOR OIL AND GAS
SUPPORT GUIDE FOR OPITO GLOBAL
LEVEL 1 TRAINING CERTIFICATES FOR
BASIC MAINTENANCE PRACTICES
VERSION 1: MARCH 2014
OPITO Global Support Guide for Level 1 Training Certificates:
Basic Maintenance Practices
VERSION CONTROL
Version 1
AMENDMENT & DATE
March 2014
PAGES
CHANGES
MADE BY
CHECKED BY
APPROVED
BY
Any amendments to this Support Guide made by OPITO will be recorded above.
Version 1 – March 2014
2
OPITO Global Support Guide for Level 1 Training Certificates:
Basic Maintenance Practices
Contents
Section 1 - Introduction ................................................................................................................ 5
The Purpose of this Guide ......................................................................................................... 5
OPITO Framework of Global Oil and Gas Technical Standards and Qualifications ....................... 5
Section 2 – Qualifications ............................................................................................................. 7
Section 3 – Delivery Guidance ...................................................................................................... 9
Target Group ............................................................................................................................ 9
English Language Skills.............................................................................................................. 9
Notional Learning Hours ........................................................................................................... 9
Approaches to Learning, Teaching and Assessment ................................................................. 10
Level 1 Artifact ....................................................................................................................... 10
Level 1 Engineering Drawing ................................................................................................... 11
Workshop and Equipment Requirements ................................................................................ 11
Section 4 – Further Guidance ..................................................................................................... 12
Section 5 – Overview of OPITO Global Technical Standards for Maintenance (Level 1) ................ 13
OGTS/L1 M10: Health and Safety in Maintenance Workshops ................................................. 13
OGTS/L1 – M11: Basic Maintenance Techniques and Workshop Practices ............................... 13
OGTS/L1 – M12: Basic Maintenance Hand Tools ..................................................................... 14
OGTS/L1- M13: Basic Measuring and Marking-out Instruments ............................................... 15
OGTS/L1 - M14: Basic Engineering Communications ................................................................ 15
OGTS/L1 - M15: Basic Numeracy Skills ................................................................................... 16
OGTS/L1 - M16: An Introduction to Physical Science and Basic Properties of Materials............ 16
OGTS/L1 - M17: Electrical and Electronic Principles ................................................................. 17
OGTS/L1 – MM20: An Introduction to Mechanical Maintenance: Prime Movers ...................... 18
OGTS/L1 – MM21: An Introduction to Mechanical Maintenance: Transmission Systems and
Components ........................................................................................................................... 18
OGTS/L1 – MM22: An Introduction to Mechanical Maintenance: Distribution Systems ........... 18
OGTS/L1 – ME25: An Introduction to Electrical Maintenance: Rotating Equipment and Tools .. 19
OGTS/L1 – ME26: An Introduction to Electrical Maintenance: Electrical Distribution Systems .. 19
OGTS/L1 – ME27: An Introduction to Electrical Maintenance: Protection Methods .................. 19
Version 1 – March 2014
3
OPITO Global Support Guide for Level 1 Training Certificates:
Basic Maintenance Practices
OGTS/L1 – MI30: An Introduction to Instrument and Control Maintenance: Process
Measurement Systems and Equipment ................................................................................... 20
OGTS/L1 – MI31: An Introduction to Instrument and Control Maintenance: Process Control
Systems and Equipment ......................................................................................................... 20
OGTS/L1 – MI32: An Introduction to Instrument and Control Maintenance: Protection and
Detection Systems .................................................................................................................. 20
Version 1 – March 2014
4
OPITO Global Support Guide for Level 1 Training Certificates:
Basic Maintenance Practices
Section 1 - Introduction
The Purpose of this Guide
This document provides guidance on the delivery of the following OPITO Global Training Certificates:

OPITO Global Level 1 Training Certificate: Basic Maintenance Practices

OPITO Global Level 1 Training Certificate: Basic Maintenance Practices (Mechanical)

OPITO Global Level 1 Training Certificate: Basic Maintenance Practices (Electrical)

OPITO Global Level 1 Training Certificate: Basic Maintenance Practices (Instrument and Control)
OPITO Framework of Global Oil and Gas Technical Standards and Qualifications
The OPITO Framework of Global Oil and Gas Technical Standards and Qualifications comprises:



Training Standards which set benchmarks for the assessment of skills and knowledge and this provides a
foundation for building the skills required to work in the oil and gas industry
Occupational Standards which define the expected level of performance, knowledge, understanding and
behaviour an individual must achieve when carrying out job roles/functions in the workplace
Global Certificates and Qualifications which have been developed in conjunction with our awarding body
partner SQA and which will have global recognition.
Occupational Standards
Training Standards
Training
Skills Assessment
Competence Assessment
Training for safety,
behaviours, knowledge,
equipment and tools
Assessment of skills in a
simulated/ realistic working
environment
Assessment of competence in
the workplace.
Foundation Certificate in
Oil and Gas
Global
Skills Qualification
Global
Vocational Qualification
Global Training Certificates
Version 1 – March 2014
5
OPITO Global Support Guide for Level 1 Training Certificates:
Basic Maintenance Practices
The OPITO Framework of Global Oil and Gas Technical Standards and Qualifications was designed in
partnership with industry and covers 6 levels which reflect the range of skills and increasing levels of
complexity and risk associated with job roles in the industry.
Oil and Gas Level 5
Professional, senior/department manager.
Oil and Gas Level 4
Expert, specialist, first line manager
Oil and Gas Level 3
Maintenance technician, supervisor
Oil and Gas Level 2
Maintenance craftsman (routine maintenance)
Oil and Gas Level 1
Entry level employment/apprentice
Oil and Gas Foundation
Trainee at basic skills level
A typical progression route through the OPITO Framework of Global Oil and Gas Technical Standards and
Qualifications is illustrated below.
Training
Training Certificate:
Maintenance Practice
– M, E, I&C
Training Certificate:
Basic Maintenance
Practice
duction
Training Certificate:
Introduction to
Workshop Practice
Version 1 – March 2014
Skills Assessment
Skills Qualification:
Maintenance
Techniques – M, E, I&C
Competence
Assessment
Vocational Qualification:)
Oil and Gas Engineering
Maintenance – M, E, I&C
Oil and Gas
Level 3
Vocational Qualification:
Oil and Gas Engineering
Maintenance – M, E, I&C
Oil and Gas
Level 2
Oil and Gas
Level 1
Oil and Gas
Foundation
6
OPITO Global Support Guide for Level 1 Training Certificates:
Basic Maintenance Practices
Section 2 – Qualifications
The OPITO Global Level 1 Training Certificate: Basic Maintenance Practice provides an introduction to the
maintenance techniques required an oil and gas maintenance workshop.
This Training Certificate consists of eight mandatory OPITO Global Training Standards at Oil and Gas Level 1:

OGTS/L1 – M10: Basic Health and Safety in Maintenance Workshops

OGTS/L1 – M11: Basic Maintenance Techniques and Workshop Practices

OGTS/L1 – M12: Basic Maintenance Hand Tools

OGTS/L1 – M13: Basic Measuring and Marking-out Instruments

OGTS/L1 – M14: Basic Engineering Communications

OGTS/L1 – M15: Basic Numeracy Skills

OGTS/L1 – M16: An Introduction to Physical Science and Basic Properties of Materials

OGTS/L1 – M17: An Introduction to Electrical and Electronic Principles
In addition, there are nine further optional OPITO Global Training Standards at Level 1 grouped by
equipment type:
An Introduction to Mechanical Maintenance:

OTGS/L1 – MM20: Prime Movers

OTGS/L1 – MM21: Transmission Systems and Components

OTGS/L1 – MM22: Distribution Systems
An Introduction to Electrical Maintenance:

OTGS/L1 – ME25: Rotating Equipment and Tools

OTGS/L1 - ME26: Electrical Distribution

OTGS/L1 - ME27: Protection Methods
An Introduction to Instrument and Control Maintenance:

OTGS/L1 – MI30: Process Measurement Systems and Equipment

OTGS/L1 – MI31: Process Control Systems and Equipment

OTGS/L1 – MI32: Protection and Detection Systems
Candidates who also complete one or more of the optional equipment groupings, in addition to the eight
mandatory OPITO Global Training Standards, will also receive the following Training Certificates:

OPITO Global Level 1 Training Certificate : Basic Maintenance Practices (Mechanical)

OPITO Global Level 1 Training Certificate : Basic Maintenance Practices (Electrical)

OPITO Global Level 1 Training Certificate : Basic Maintenance Practices (Instrument and Control)
Version 1 – March 2014
7
OPITO Global Support Guide for Level 1 Training Certificates:
Basic Maintenance Practices
The OPITO Global Level 1 Training Certificates for Basic Maintenance Practice are jointly awarded by OPITO
and SQA and successful Candidates who complete the relevant Training Standards will be issued with a joint
OPITO/SQA certificate.
This Training Certificate is at Oil and Gas Level 1. This is broadly comparable to training at SCQF level 4,
S/NVQ level 1, QCF level 1 and EQF level 2.
On successful completion of these Training Certificates, Candidates can progress to the Level 2 Training
Certificates for Maintenance Practice as illustrated below.
Training Certificate:
Maintenance Practice
(Electrical)
Training Certificate:
Maintenance Practice
(Instrument and Control)
Training Certificate:
Maintenance Practice
(Mechanical)
Training Certificate:
Basic Maintenance Practice
(Electrical)
Training Certificate:
Basic Maintenance Practice
(Instrument and Control)
Training Certificate:
Basic Maintenance Practice
(Mechanical)
Training Certificate:
Basic Maintenance
Practice
Version 1 – March 2014
Oil and Gas
Level 2
Oil and Gas
Level 1
8
OPITO Global Support Guide for Level 1 Training Certificates:
Basic Maintenance Practices
Section 3 – Delivery Guidance
Target Group
The Training Certificates at Oil and Gas Level 1 are aimed at Candidates with very little prior experience of an
engineering workshop environment. Candidates are likely to possess some basic numeracy skills. It is
recommended that Candidates should complete the OPITO Global Foundation Training Certificate in
Maintenance Workshop Practice or equivalent training before undertaking these Training Certificates.
English Language Skills
All assessment must be carried out in English and Candidates should be able to deal with simple,
straightforward information and to express ideas in familiar contexts. They should be able to understand
sentences and frequently used expressions relevant to the workplace. They should be able to communicate
with others about routine tasks involving a simple and direct exchange of information. This level of English
is to the following International Frameworks - CEFR B1/IELTs 4.0.
Notional Learning Hours
The time taken to complete the Training Certificates varies depending on circumstances and experience. It
is anticipated that, on average, it should take a Candidate around 230 hours to complete the mandatory
Level 1 Training Standards and a further 90 hours for each of the additional equipment groups.
Level 1 Training Standards
Mandatory Training Standards
Basic Health and Safety in Maintenance Workshops
Basic Maintenance Techniques and Workshop Practices
Basic Maintenance Hand Tools
Basic Measuring and Marking-out Instruments
Basic Engineering Communications
Basic Numeracy Skills
An Introduction to Physical Science and Basic Properties of Materials
An Introduction to Electrical and Electronic Principles
Optional Equipment Training Standards
An Introduction to Mechanical Maintenance: Prime Movers
An Introduction to Mechanical Maintenance: Transmission Systems and Components
An Introduction to Mechanical Maintenance: Distribution Systems
An Introduction to Electrical Maintenance: Rotating Equipment and Tools
An Introduction to Electrical Maintenance: Electrical Distribution
An Introduction to Electrical Maintenance: Protection Methods
Version 1 – March 2014
Notional hours
(including
assessment)
30
20
30
30
30
30
30
30
30
30
30
30
30
30
9
OPITO Global Support Guide for Level 1 Training Certificates:
Basic Maintenance Practices
An Introduction to Instrument and Control Maintenance: Process Measurement
Systems and Equipment
An Introduction to Instrument and Control Maintenance: Process Control Systems
and Equipment
An Introduction to Instrument and Control Maintenance: Protection and Detection
Systems
30
30
30
Approaches to Learning, Teaching and Assessment
The Level 1 Training Certificates are intended to prepare Candidates to begin to undertake basic
maintenance work in an engineering workshop. The learning and teaching approaches should introduce and
a range of basic techniques and principles and prepare Candidates to progress to carrying out routine
maintenance.
Learning and teaching should take place in a supervised workshop environment with trainers and
supervisors providing regular feedback.
Candidates should be encouraged to use basic engineering terminology as they progress through the
Standards. Candidates should be provided with checklists to assist them to develop relevant skills e.g.
checklist for the selection of hand tools and measuring and marking-out instruments.
The production of an artifact can be used to provide an integrated approach to delivering practical elements
of the Standards. Candidates should be provided with a specification (see below) which will allow them to
combine the skills and knowledge they acquire and accumulate through a number of the Standards,
including:
 Basic Health and Safety in Maintenance Workshops
 Basic Maintenance Hand Tools
 Basic Measuring and Marking-out Instruments
 Basic Engineering Communications
Knowledge-based elements of the Standards should be assessed by means of written and oral assessment
using simple structured questions – examples include short response questions, matching questions,
multiple choice questions and partly completed diagrams. If oral questions are used, an accurate record of
questions asked and responses given must be retained. Free-text written responses should be limited to
short responses in either written or oral form.
Level 1 Artifact
Candidates are required to produce an artifact which conforms to a given brief.
The design of the artifact itself is at the discretion of the delivery centre but it should conform to the
following parameters:
 it should be a simple rectangular shape to specified dimensions to be produced from 6mm sheet metal
 it should include at least one 30 or 45 degree angle
 it must also include at least 2 different size drilled holes with sufficient capacity to allow fitting of small
screws, bolts, washers and nuts
 it must also include least 1 threaded bar, and a curved element as part of the design and at least 1
tapped hole.
Version 1 – March 2014
10
OPITO Global Support Guide for Level 1 Training Certificates:
Basic Maintenance Practices
Level 1 Engineering Drawing
Candidates are required to prepare detailed two-dimensional engineering drawings of engineering objects in
third angle projection as part of the Basic Engineering Communications Training Standard. Candidates must
complete the following details on each drawing:
 three views in total
 the correct projection symbol
 fully dimensioned
 two drawing symbols
 three abbreviations to current relevant Standards
Example of engineering object
Workshop and Equipment Requirements
Training should take place in a supervised workshop setting which gives Candidates access to basic tools and
personal protective equipment (PPE). Typical PPE would include overalls, boots, safety glasses, gloves, ear
defenders, hard hat.
The training area should be designed to enable Candidates to view, hear and participate fully in the subject
matter being taught.
Typical workshops and practical areas should be well lit and well ventilated with clearly defined walk ways.
Training areas should have adequate floor space with work benches with bench vices fitted, allowing each
Candidate to participate fully in practical demonstrations and exercises.
There should also be a clearly marked storage area with tools cupboards and toolboxes/trays and file racks.
Delivery centres are responsible for ensuring that all tools and equipment are maintained and meet relevant
safety standards.
Version 1 – March 2014
11
OPITO Global Support Guide for Level 1 Training Certificates:
Basic Maintenance Practices
Section 4 – Further Guidance
This document provides an overview of the Training Standards which form part of the OPITO Global Level 1
Training Certificates for Basic Maintenance Practice. The full specifications for Training Standards are
included in the OPITO Guide - OPITO Global Technical Standards and Qualifications Specifications for
Maintenance (Level 1).
All organisations wishing to deliver the OPITO Global Foundation Training Certificate in Maintenance
Workshop Practice must be an OPITO Approved Centre and must meet the requirements of OPITO’s Quality
Criteria for Global Oil and Gas Technical Standards and Qualifications.
For further information please contact a member of our Workforce Development team in Dubai mea.enquiries@opito.com
Version 1 – March 2014
12
OPITO Global Support Guide for Level 1 Training Certificates:
Basic Maintenance Practices
Section 5 – Overview of OPITO Global Technical Standards for
Maintenance (Level 1)
OGTS/L1 M10: Health and Safety in Maintenance Workshops
Summary
This Training Standard develops the skills required to comply with safe working practices in
a maintenance workshop environment
Outcome 1
Describe safe working practices and procedures for a maintenance workshop
 describe safe working practices for working in a maintenance workshop
 describe the operation of safety documentation and procedures
 identify relevant emergency requirements for a maintenance workshop
Outcome 2
Create a basic risk assessment for workshop maintenance tasks
 identify potential hazards in a workshop environment
 describe the associated risks and implications for people, equipment and the
environment
 describe measures that could be taken to minimise the risks
Outcome 3
Demonstrate safe working practices in a maintenance workshop
 communicate and work effectively as part of a team for maintenance tasks
 take part in a tool box talk
 use correct manual handling techniques for maintenance tasks
 select and us the correct personal protection equipment for maintenance tasks
 maintain the workspace in a clean and tidy manner and dispose of waste
The full specification for this Training Standard is included in the OPITO Guide - OPITO Global Technical
Standards and Qualifications Specifications for Maintenance (Level 1).
OGTS/L1 – M11: Basic Maintenance Techniques and Workshop Practices
Summary
Outcome 1
Outcome 2
Outcome 3
This Training Standard covers the skills required to prepare for and carry out basic routine
maintenance tasks
Prepare for basic routine maintenance tasks
 identify tools, equipment and material that would be required for a range of basic
routine maintenance tasks
 prepare the tools, equipment and materials for given maintenance tasks
 prepare the work area for given maintenance tasks
Describe basic routine maintenance techniques
 describe the role of cleaning and relevant techniques and materials that are used
during routine maintenance
 describe the role of lubrication and relevant techniques and materials that are used
during routine maintenance
 describe adjustments that may be made to equipment during routine maintenance
 describe basic inspection procedures that are used during routine maintenance
 identify safety requirements for materials that are used in routine maintenance tasks
Carry out basic routine maintenance tasks
 carry out appropriate cleaning routines using the correct cleaning agents
 carry out routine lubrication, using the correct lubricant for the application
 check oil levels and add oil as required
 tighten fastenings using correct tools and equipment
 check tensions and adjust as required
Version 1 – March 2014
13
OPITO Global Support Guide for Level 1 Training Certificates:
Basic Maintenance Practices
Outcome 4
Carry out basic inspections
 carry out basic visual inspection for common faults
 record observed faults
Outcome 5
Clear work areas following maintenance tasks
 store relevant tools, equipment and materials in appropriate locations
 clear the workshop area and dispose of waste
The full specification for this Training Standard is included in the OPITO Guide - OPITO Global Technical
Standards and Qualifications Specifications for Maintenance (Level 1).
OGTS/L1 – M12: Basic Maintenance Hand Tools
Summary
This Training Standard develops the skills required to use safely, care for and store a range
of basic hand tools, identify basic parts and functions and select appropriate hand tools to
carry out routine maintenance and workshop tasks.
Outcome 1
Identify the use of basic maintenance hand tools
 identify the parts and purpose of a range of basic maintenance hand tools
 select appropriate hand tool for specified maintenance and workshop tasks
Outcome 2
Demonstrate the use of basic hand tools for maintenance tasks and the production of an
artefact
 use basic maintenance hand tools correctly during simple maintenance dismantling
and assembly procedures
 use basic maintenance hand tools correctly during a basic routine maintenance tasks
 use basic maintenance hand tools to produce a given artifact
 follow relevant safe working practices when using maintenance hand tools
Outcome 3
Demonstrate the care of basic maintenance hand tools
 identify if hand tools are in good working order before using them
 identify typical care requirements of a range of hand tools
 carry out basic care steps to ensure hand tools are maintained in good working order
after use
 return hand tools to safe storage location following their use
The full specification for this Training Standard is included in the OPITO Guide - OPITO Global Technical
Standards and Qualifications Specifications for Maintenance (Level 1).
Version 1 – March 2014
14
OPITO Global Support Guide for Level 1 Training Certificates:
Basic Maintenance Practices
OGTS/L1- M13: Basic Measuring and Marking-out Instruments
Summary
This Training Standard involves the skills to use safely, care for and store a range of basic
measuring and marking-out instruments and tools and select appropriate
instruments/tools to carry out routine maintenance and workshop tasks.
Outcome 1
Outline the use of basic measuring and marking-out instruments
 identify the purpose of a range of measuring and marking-out instruments and tools
and precision measuring instruments
 select appropriate instruments and tools for specified maintenance tasks
Outcome 2
Select and use basic measuring and marking-out instruments
 demonstrate the ability to read measurements using basic measuring and marking-out
instruments and precision measuring instruments in metric and imperial units
 use a range of measuring and marking-out instruments/tools to take accurate
measurements within given tolerances for given maintenance tasks
 use measuring and marking-out instruments to take relevant measurements and mark
out component or work pieces when producing a specified artifact
Outcome 3
Demonstrate care of basic measuring and marking-out instruments
 identify if measuring and marking-out instruments are in good working order before
using them
 carry out basic care steps to ensure measuring and marking-out instruments/tools are
maintained in good working order after use
 return measuring and marking-out instruments/tools to safe storage location following
their use
The full specification for this Training Standard is included in the OPITO Guide - OPITO Global Technical
Standards and Qualifications Specifications for Maintenance (Level 1).
OGTS/L1 - M14: Basic Engineering Communications
Summary
Outcome 1
Outcome 2
This Training Standard develops the skills required to use engineering drawings/diagrams
and verbal and written engineering instructions in the context of maintenance tasks.
Interpret engineering communications and symbols
 extract information from two-dimensional and three-dimensional engineering
drawings
 extract information for basic engineering drawing symbols
 identify correct use of basic engineering drawing symbols
 interpret supplied instructions and drawings to identify key specifications for creating
for a given artifact
Prepare basic two-dimensional drawings
 prepare basic two-dimensional drawings of engineering objects to scale
 add dimensions to basic two-dimensional drawings
Version 1 – March 2014
15
OPITO Global Support Guide for Level 1 Training Certificates:
Basic Maintenance Practices
OGTS/L1 - M15: Basic Numeracy Skills
Summary
This Training Standard develops the skills required to gain an understanding of numeracy
in an engineering context.
Outcome 1
Perform basic arithmetical operations to solve problems in an engineering context
 perform calculations involving use of whole numbers, decimals, percentages, fractions,
ratios and positive, negative and very large or small numbers
 perform calculations involving statistical concepts
 perform basic calculations using symbols, formulae and scientific notation
Outcome 2
Use basic graphs in an engineering context
 extract information from qualitative graphs and histograms
 interpret information from graphs where part of the axis has been omitted
The full specification for this Training Standard is included in the OPITO Guide - OPITO Global Technical
Standards and Qualifications Specifications for Maintenance (Level 1).
OGTS/L1 - M16: An Introduction to Physical Science and Basic Properties of Materials
Summary
This Training Standard develops the skills required to gain a basic understanding of
physical science and the properties of materials in an engineering context.
Outcome 1
Outline the basic principles of matter and atomic structure in an engineering context
 identify phase changes and the basic properties of solids, liquids and gases
 describe the basic concept of atomic structure
 identify the key principles of the periodic table of the elements
 describe the basic principles of elements and compounds
Outcome 2
Outline the basic properties of materials in an engineering context
 identify the key features and mechanisms of wear and corrosion
 describe the key features of the concepts of density, reactivity and magnetism
 describe the key features of electrical and thermal conductivity of materials
 describe the key features of the concepts of hardness, ductility, plasticity, toughness
and malleability
Outcome 3
Outline the basic principles of mechanics in an engineering context
 give an overview of the concepts of force, mass and acceleration
 give an overview of the basic principles underlying statics and dynamics including the
key concepts of equilibrium, centre of mass, moment of inertia and torque
 give an overview of the concepts of work, energy, power and friction
 describe the concept of and the relationship between speed, velocity and acceleration
 describe the operation of simple machines such as levers, gears, springs and pulleys
Outcome 4
Carry out simple mechanics calculations in an engineering context
 carry out simple calculations involving force, mass and acceleration
 carry out simple calculations involving work, energy and power
 carry out simple calculations involving speed, velocity and acceleration
 carry out simple calculations involving levers, gears, springs and pulleys
The full specification for this Training Standard is included in the OPITO Guide - OPITO Global Technical
Standards and Qualifications Specifications for Maintenance (Level 1).
Version 1 – March 2014
16
OPITO Global Support Guide for Level 1 Training Certificates:
Basic Maintenance Practices
OGTS/L1 - M17: Electrical and Electronic Principles
Summary
This Training Standard develops the skills required to gain a basic understanding of
electrical and electronic principles in an engineering context.
Outcome 1
Outline the basic principles of atomic structure and electron theory
 provide a basic overview of atomic structure and electron theory
 outline the influence of atomic structure and electron theory on electrical properties
of materials
Outcome 2
Outline the basic principles of magnetism and electromagnetism
 provide a basic overview of magnetism
 provide a basic overview of electromagnetism
Outcome 3
Outline and use the basic principles of voltage, current and resistance and series and
parallel circuits
 provide a basic overview of Ohm’s law
 identify the components of simple series and parallel electrical circuits
 perform simple calculations on simple series and parallel electrical circuits
 explain the operation of a simple alternating current (AC) generator
Outcome 4
Outline the basic principles of electronics
 provide a basic description of diodes and their application
 describe half and full-wave rectification
 provide a basic description of transistors and thyristors and their use in electronic
circuits
The full specification for this Training Standard is included in the OPITO Guide - OPITO Global Technical
Standards and Qualifications Specifications for Maintenance (Level 1).
Version 1 – March 2014
17
OPITO Global Support Guide for Level 1 Training Certificates:
Basic Maintenance Practices
OGTS/L1 – MM20: An Introduction to Mechanical Maintenance: Prime Movers
Summary
The Training Standard develops the skills required to gain an overview of the operation of
prime movers, their key functions, typical applications in the oil and gas industry and
typical maintenance issues and requirements.
Outcome 1
Describe the key features of prime movers
 describe the typical operation of prime movers
 identify the typical use and application of prime movers in the oil and gas industry
Outcome 2
Outline typical maintenance requirements of prime movers
 outline typical maintenance issues for prime movers
 describe typical types of maintenance requirements and schedules for prime movers
The full specification for this Training Standard is included in the OPITO Guide - OPITO Global Technical
Standards and Qualifications Specifications for Maintenance (Level 1).
OGTS/L1 – MM21: An Introduction to Mechanical Maintenance: Transmission Systems and
Components
Summary
Outcome 1
Outcome 2
The Training Standard develops the skills required to gain an overview of the operation of
transmission systems and components, their key functions, typical applications in the oil
and gas industry and typical maintenance issues and requirements.
Describe the key features of transmission systems and components
 describe the typical operation of transmission systems and components
 identify the typical use and application of transmission systems and components in the
oil and gas industry
Outline typical maintenance requirements of transmission systems and components
 outline typical maintenance issues for transmission systems and components
 describe typical types of maintenance requirements and schedules for transmission
systems and components
OGTS/L1 – MM22: An Introduction to Mechanical Maintenance: Distribution Systems
Summary
The Training Standard develops the skills required to gain an overview of the operation of
distribution systems, their key functions, typical applications in the oil and gas industry and
typical maintenance issues and requirements.
Outcome 1
Describe the key features of distribution systems
 describe the typical operation of distribution systems
 identify the typical use and application of distribution systems in the oil and gas
industry
Outcome 2
Outline typical maintenance requirements of distribution systems
 outline typical maintenance issues for distribution systems
 describe typical types of maintenance requirements and schedules for distribution
systems
The full specification for this Training Standard is included in the OPITO Guide - OPITO Global Technical
Standards and Qualifications Specifications for Maintenance (Level 1).
Version 1 – March 2014
18
OPITO Global Support Guide for Level 1 Training Certificates:
Basic Maintenance Practices
OGTS/L1 – ME25: An Introduction to Electrical Maintenance: Rotating Equipment and Tools
Summary
The Training Standard develops the skills required to gain an overview of the operation of
rotating equipment and tools, their key functions, typical applications in the oil and gas
industry and typical maintenance issues and requirements.
Outcome 1
Describe the key features of rotating equipment and tools
 describe the typical operation of rotating equipment and tools
 identify the typical use and application of rotating equipment and tools in the oil and
gas industry
Outcome 2
Outline typical maintenance requirements of rotating equipment and tools
 outline typical maintenance issues for rotating equipment and tools
 describe typical types of maintenance requirements and schedules for rotating
equipment and tools
The full specification for this Training Standard is included in the OPITO Guide - OPITO Global Technical
Standards and Qualifications Specifications for Maintenance (Level 1).
OGTS/L1 – ME26: An Introduction to Electrical Maintenance: Electrical Distribution Systems
Summary
The Training Standard develops the skills required to gain an overview of the operation of
electrical distribution systems, their key functions, typical applications in the oil and gas
industry and typical maintenance issues and requirements.
Outcome 1
Describe the key features of electrical distribution systems
 describe the typical operation of electrical distribution systems
 identify the typical use and application of electrical distribution systems in the oil and
gas industry
Outcome 2
Outline typical maintenance requirements of electrical distribution systems
 outline typical maintenance issues for electrical distribution systems
 describe typical types of maintenance requirements and schedules for electrical
distribution systems
The full specification for this Training Standard is included in the OPITO Guide - OPITO Global Technical
Standards and Qualifications Specifications for Maintenance (Level 1).
OGTS/L1 – ME27: An Introduction to Electrical Maintenance: Protection Methods
Summary
The Training Standard develops the skills required to gain an overview of the operation of
protection methods, their key functions, typical applications in the oil and gas industry and
typical maintenance issues and requirements.
Outcome 1
Describe the key features of protection methods
 describe the typical operation of protection methods
 identify the typical use and application of protection methods in the oil and gas
industry
Outcome 2
Outline typical maintenance requirements of protection methods
 outline typical maintenance issues for protection methods
 describe typical types of maintenance requirements and schedules for protection
methods
The full specification for this Training Standard is included in the OPITO Guide - OPITO Global Technical
Standards and Qualifications Specifications for Maintenance (Level 1).
Version 1 – March 2014
19
OPITO Global Support Guide for Level 1 Training Certificates:
Basic Maintenance Practices
OGTS/L1 – MI30: An Introduction to Instrument and Control Maintenance: Process
Measurement Systems and Equipment
Summary
The Training Standard develops the skills required to gain an overview of the operation of
process measurement systems and equipment, their key functions, typical applications in
the oil and gas industry and typical maintenance issues and requirements.
Outcome 1
Describe the key features of process measurement systems and equipment
 describe the typical operation of process measurement systems and equipment
 identify the typical use and application of process measurement systems and
equipment in the oil and gas industry
Outcome 2
Outline typical maintenance requirements of process measurement systems and
equipment
 outline typical maintenance issues for process measurement systems and equipment
 describe typical types of maintenance requirements and schedules for process
measurement systems and equipment
The full specification for this Training Standard is included in the OPITO Guide - OPITO Global Technical
Standards and Qualifications Specifications for Maintenance (Level 1).
OGTS/L1 – MI31: An Introduction to Instrument and Control Maintenance: Process Control
Systems and Equipment
Summary
The Training Standard develops the skills required to gain an overview of the operation of
process control systems and equipment, their key functions, typical applications in the oil
and gas industry and typical maintenance issues and requirements.
Outcome 1
Describe the key features of process control systems and equipment
 describe the typical operation of process control systems and equipment
 identify the typical use and application of process control systems and equipment in
the oil and gas industry
Outcome 2
Outline typical maintenance requirements of process control systems and equipment
 outline typical maintenance issues for process control systems and equipment
 describe typical types of maintenance requirements and schedules for process control
systems and equipment
The full specification for this Training Standard is included in the OPITO Guide - OPITO Global Technical
Standards and Qualifications Specifications for Maintenance (Level 1).
OGTS/L1 – MI32: An Introduction to Instrument and Control Maintenance: Protection and
Detection Systems
Summary
The Training Standard develops the skills required to gain an overview of the operation of
protection and detection systems, their key functions, typical applications in the oil and
gas industry and typical maintenance issues and requirements.
Outcome 1
Describe the key features of protection and detection systems
 describe the typical operation of protection and detection systems
 identify the typical use and application of protection and detection systems in the oil
and gas industry
Outcome 2
Outline typical maintenance requirements of protection and detection systems
 outline typical maintenance issues for protection and detection systems
 describe typical types of maintenance requirements and schedules for protection and
detection systems
The full specification for this Training Standard is included in the OPITO Guide - OPITO Global Technical
Standards and Qualifications Specifications for Maintenance (Level 1).
Version 1 – March 2014
20