STATE BANK OF HYDERABAD
(Associate of State Bank of India)
TWO BID TENDER DOCUMENT
PART 2 .- PRICE BID
TO BE READ IN CONTINUTY WITH INSTRUCTIONS/ SPECIFICATIONS OF TECHNICAL BID
SCHEDULE OF QUANTITIES
FOR
INTERIOR WORKS
OF
REGIONAL OFFICE, SURYAPET
LAST DATE for submission of Sealed PRICE-BID :
at 3.00 PM on 18.11.2013
Tender to be submitted to:
THE DEPUTY GENERAL MANAGER,
STATE BANK OF HYDERABAD, ZONAL OFFICE,
PRAJASHAKTI BUILDING, 2nd FLOOR,
BAGHLINGAMPALLI, HYDERABAD-500020. (AP)
Tel : 040- 27680043
Contractor has to must provide below their:
E- MAIL id :
Contact No:
Postal address : ____________________________________________
_________________________________________________________
36
B.O.Q OF INTERIOR WORKS FOR REGIONAL OFFICE, SURYAPET OF S.B.H.
Sr
1
2
3
4
Items
PARTLY GLAZED WOODEN PARTITIONS
8 mm Glass
Manufacturing, supplying and fixing wooden partitions in
approved design / drawing up to required height (8 ft or
ceiling/beam bottom ht.) & made of 2.5" x 1.5" M. teakwood
vertical supporting members spaced approximately at 2.0' to
3.0' c/c (c/c distance to be adjusted as per drawings,
door/opening positions) and joined with Horizontal members of
2.5" x 1.5" M. teak wood section and spaced approximately at
1.5’ to 2.0’ c/c subject to site instructions. solid portion of
partitions will be covered with 8mm Plywood of approved make
on both sides. Partition shall be glazed up to 7.0 ft ht. above
the 0.50 ft ht. from floor level . Glazed portion of partition shall
be done with 8 mm plain float glass of approved make with
etching work (acid wash) as per design and glass is to be fixed
in BTC strip of 1”x 0.5” section and polished with zinc oxide
polish to match color of laminate. solid portion of partitions will
be laminated on both sides with approved make laminate of 1.5
mm thick laminate of approved regular shade/ 1.0mm thick
laminate of approved premium shade with fixing adhesive etc.
Vertical and horizontal groves as per drawing /site conditions.
Design / pattern of partition shall be as per approval of
engineer-in-charge. cost to include all material and Labour
charges.
PARTLY GLAZED WOODEN LOW HT PARTIONS
12mmGlass
Manufacturing, supplying and fixing wooden partitions up to 4.0
ft. height in approved design & made of 2.5" x 1.5" M.
teakwood vertical supporting members spaced approximately
at 2.0' to 3.0' c/c (c/c distance to be adjusted as per drawings,
door/opening positions) and joined with Horizontal members of
2.5" x 1.5" M. teak wood section and spaced approximately at
1.5’ to 2.0’ c/c subject to site instructions. solid portion of
partitions will be covered with 8mm Plywood of approved make
on both sides. Partition shall be glazed up to 4.0 ft. ht. above
the 3.0 ft. ht. from floor level . Glazed portion of partition to be
done with 12 mm plain float glass of approved make with
etching work (acid wash) as per design and glass is to be fixed
in BTC strip of 1”x0.5” section and polished with zinc oxide
polish to match color of laminate. solid portion of partitions will
be laminated on both sides with approved make laminate of 1.5
mm thick laminate of approved regular shade/ 1.0mm thick
laminate of approved premium shade with fixing adhesive etc.
Vertical and horizontal groves as per drawing /site conditions.
Design / pattern of partition to be as per approval of engineerin-charge. cost to include all material and Labour charges.
ALUMUNIUM COPOSITE PANELLING :
Manufacturing, supplying and fixing ALUMINUM COPOSITE
PANELLING of ALSTONE or equivalent approved make in
approved design / drawing up to required height. Vertical and
horizontal groves as per drawing /site conditions. Design /
pattern of partition shall be as per approval of engineer-incharge. Cost to include all material and Labour charges.
DOOR WITH FLOOR SPRING
Supply and fixing of 35 mm thick. Solid core door shutter of
approved make and laminated with 1.5 mm thick laminate of
approved regular shade/ 1.0mm thick laminate of approved
premium shade and make on both sides. A door frame made
Rate (Rs.)
Qty
Unit
590
sq.ft
548
sq.ft
50
sq.ft
8
no.
Amount
37
5
6
7
with beach wood of 56.25mmx87.5mm size shall be provided.
The door shall be glazed with 8 mm float glass (having etching
work) OR grilled with powder coated germo décor aluminum
grill of approved pattern make etc. Glazed / grilled portion of
door shall be done in the same line / pattern as of the partition
to which it is fixed. All open edges of door shall be leaped with
M. Teak Wood beading. The door shall be fitted on floor spring
door closer of approved make with top pivot, brush steel finish
handle, 6 lever mortise lock set of three keys, heavy door
stopper and all other fittings and fixture etc. complete and as
per design and approval of Engineer-in-charge.
FULLY GLAZED MAIN DOOR (with plywood frame)
Supplying and Fixing of fully glazed main door in single /
double leaf shutter at approved position. The door shall be
made of 12 mm thick float glass & the glass shall be fitted in a
6 inches wide C – frame made with two layers of 19mm
plywood and one layer of 12mm plywood and the height of C –
frame shall be as per site condition. The 12mm plywood
member shall be sandwiched from it’s both sides by the two18
mm plywood members and the joints shall be made as per the
drawing and instructions of the engineer-in-charge. A door
frame made with beach wood of 62mmx75mm size shall be
provided. The door shall be fixed on heavy duty floor spring
hinges and with 2 Nos. of 18 inch S.S. handles, one dead lock
with three keys, its fittings and fixtures, computerized vinyl
push/pull sticker etc. complete all of approved make. The fully
glazed door shall have entrance door frame in box shape
having horizontal & vertical member. The horizontal & vertical
member of the frame shall be of 6.0”x 2.25” overall size at the
periphery of entrance & all made out of 19 mm plywood and
laminated with 1.5 mm thick laminate of approved regular
shade/ 1.0mm thick laminate of approved premium shade. The
12 mm thick glass shall have etching work (acid wash) done on
it as per the drawing. Door handle shall be of Kich Industries
make, stainless steel, AISI 316 grade pull handles, 22 mm dia x
300 mm STAIN CODE PHI 2212 S and shall be fixed in
position. The cost to include all fixtures, 6 lever Godrej lock,
push/pull stickers, Labour etc. complete and all as per design
and approval of the Engineer in charge.
50
sq.ft
12mm Glass Door with Patch fitting work
Supplying and Fixing of fully glazed Door (in single / double leaf
shutter) at approved position. The door shall be made of 12
mm thick toughened float glass & the glass shall be fitted with
Patch Fittings of approved make. The door shall be fixed on
approved make floor spring and with 2 Nos. of 18 inch S.S.
handles, one dead lock with three keys, its fittings and fixtures,
computerized vinyl push/pull sticker etc. complete all of
approved make. The 12 mm thick glass shall have etching
work (acid wash) done on it as per the drawing/ approval. Door
handle shall be of Kich Industries make, stainless steel, AISI
316 grade pull handles, 22 mm dia x 450 mm STAIN CODE
PHI 2212 S and shall be fixed in position. The cost to include
all fixtures, 6 lever Godrej lock, push/pull stickers, Labour etc.
complete and all as per design and approval of the Engineer in
charge.
SENIOR EXECUTIVE WORK STATION ( WITH LAMINATE)
Manufacturing and supplying ‘ L’ shaped Executive work station
consisting of a table made with necessary 19mm Plywood (of
approved make) frame work having 16" wide and 2.0’ deep
storage unit on one side consisting of Four 5" deep sliding
drawers and a modesty panel with embossed design. The table
frame work shall be of over all size of 7.5’ x 2.5' x 2.5' and it
shall be fitted with 12mm glass on it’s top. There shall be a side
unit of 4.0' x 1’-6” x 2’-6” over all size made with 19mm
50
1
sq.ft
no.
38
8
9
Plywood (of approved make) frame work having 3nos. of 5”
deep drawers on upper side and below to drawers, the
cupboard unit shall be with folding shutter & adjustable shelf all
along the full width of the credenza. In the table. Arrangement
of CPU stand, key board drawer, cable manager and foot rest
of 4" x 1.5" teak wood section shall be provided and the three
edges of front fascia shall be 1.5" thick with additional ply and
leaped with necessary beach wood beading of same thickness
melamine polished to same colour as veneer.. All drawer shall
be fitted with telescopic channels and automatic push type
locking arrangement and cupboards shall have locking
arrangement and all exposed edges of ply wood shall be fitted
with teak wood beading duly polished. All bidding shall have
polish of matching color. All exposed and visible surfaces shall
be laminated with 1.5 mm thick laminate of approved regular
shade/ 1.0mm thick laminate of approved premium shade and
make and all invisible surfaces to be laminated with 0.8 mm
laminate of approved shade and make. The rates should
include locking arrangement (to be operated by single key) for
all drawers and cupboard along with best quality 4” brush steel
handles, sliding channel with roller + ball bearing arrangements
etc. complete. Cost should also inclusive of paneling, lapping
of edges with plywood to achieve thickness as per Engineer-incharges design.
EXECUTIVE WORK STATION (WITH LAMINATE)
Manufacturing and supplying ‘ L’ shaped Executive work station
consisting of a table made with necessary 19mm Plywood (of
approved make) frame work having 16" wide and 2.0’ deep
storage unit on one side consisting of Four 5" deep sliding
drawers and a modesty panel. The table frame work shall be of
over all size of 6’ x 2.5' x 2.25' and it shall be fitted with 12mm
glass top of 6’ x 3’ size ( in the approved shape) on it’s top with
75mm s.s. studs & screw. There shall be a side unit of 4.0' x 1’6” x 2’-6” over all size made with 19mm Plywood (of approved
make) frame work having 3 nos. of 5” deep drawers on upper
side and below to drawers, the cupboard unit shall be with
folding shutter & adjustable shelf all along the full width of the
credenza. In the table. Arrangement of CPU stand, key board
drawer, cable manager and foot rest of 4" x 1.5" teak wood
section shall be provided and the three edges of front fascia
shall be 1.5" thick with additional ply and leaped with necessary
beach wood beading dully melamine polished. All drawer shall
be fitted with telescopic channels and automatic push type
locking arrangement and cupboards shall have locking
arrangement and all exposed edges of ply wood shall be fitted
with teak wood beading duly polished. All bidding shall have
melamine polish of matching color. All exposed and visible
surfaces shall be laminated with 1.5 mm thick laminate of
approved regular shade/ 1.0mm thick laminate of approved
premium shade and make and all invisible surfaces to be
laminated with 0.8 mm laminate of approved shade and make.
The rates should include locking arrangement (to be operated
by single key) for all drawers and cupboard along with best
quality 4” brush steel handles, sliding channel with roller + ball
bearing arrangements etc. complete.
Cost should also
inclusive of paneling, lapping of edges with plywood to achieve
thickness as per Engineer-in-charges design.
OFFICERS WORK STATION
Manufacturing and supplying ‘ L’ shaped officer work station
consisting of a table made with necessary 19mm Plywood (of
approved make) frame work having 16" wide and 2.0’ deep
storage unit on one side consisting of Four 5" deep sliding
drawers and a modesty panel. The table frame work shall be of
over all size of 5-0’ x 2.5' x 2.5'. There shall be a side unit of
1
no
12
no.
39
10
11
4.0' x 1’-6” x 2’-6” over all size made with 19mm Plywood (of
approved make) frame work having 3nos. of 5” deep drawers
on upper side and below to drawers, the cupboard unit shall be
with folding shutter & adjustable shelf all along the full width of
the credenza. In the table, Arrangement of CPU stand, key
board drawer, cable manager and foot rest of 4" x 1.5" teak
wood section shall be provided and the three edges of front
fascia shall be 1.5" thick with additional ply and leaped with
necessary beach wood beading dully melamine polished. All
drawer shall be fitted with telescopic channels and automatic
push type locking arrangement and cupboards shall have
locking arrangement and all exposed edges of ply wood shall
be fitted with teak wood beading duly polished. All bidding shall
have melamine polish of matching color. All exposed and
visible surfaces shall be laminated with 1.5 mm thick laminate
of approved regular shade/ 1.0mm thick laminate of approved
premium shade and make and all invisible surfaces to be
laminated with 0.8 mm laminate of approved shade and make.
The rates should include locking arrangement (to be operated
by single key) for all drawers and cupboard alongwith best
quality 4” brush steel handles, sliding channel with roller + ball
bearing arrangements etc. complete.
Cost should also
inclusive of paneling, lapping of edges with plywood to achieve
thickness as per Engineer-in-charges design.
COMPUTER WORK STATION
Supplying and fixing of Computer desks of 2.5’ H x 2.0' D size
in the given length as per drawing and made with 19mm
Plywood (of approved make) frame work having 16" wide and
2.0’ deep storage unit on one side at every 4.0’ length.
Arrangement of CPU stand, key board drawer, cable manager
and foot rest of 4" x 1.5" teak wood section shall be provided.
Each storage unit shall consist of four sliding drawers of 5"
depth & the drawers shall be fitted with telescopic channels and
automatic push type locking arrangement and all exposed
edges of ply wood shall be fitted with teak wood beading duly
polished. All bidding shall have zinc oxide polish of matching
color. All exposed and visible surfaces shall be laminated with
1.5 mm thick laminate of approved regular shade/ 1.0mm thick
laminate of approved premium shade and all invisible surfaces
to be laminated with 0.8 mm laminate of approved shade and
make. The rates should include locking arrangement (to be
operated by single key) for all drawers and cupboard alongwith
best quality 4” brush steel handles, etc. complete. Cost should
also inclusive of paneling, lapping of edges with plywood to
achieve thickness as per design and approval of Engineer-incharges.
CONFERENCE TABLE
Supplying and fixing of Oval shaped Conference Table of 2.5’
H x 2.0' W size in the given length as per design and drawing
and made with 19mm Plywood (of approved make) frame work
having table edge showing 40mm thickness (i.e. on seating
side) and 19mm thick modesty panel. Arrangement of support
(all along the length) shall be in the shape of a 0’- 6” x 2’-0” size
box frame (made with 19mm Plywood ) and these support shall
be provided at every length of 4ft. The table shall consists of
small slit doors for mics wires, cable manager and foot rest
made with 19mm ply in slanted shape from seating face to
modesty panel as per design. All exposed edges of ply wood
shall be fitted with beach wood beading duly polished. All
bidding shall have melamine polish of matching color. All
exposed and visible surfaces shall be laminated with 1.5 mm
thick laminate of approved regular shade/ 1.0mm thick laminate
of approved premium shade and all invisible surfaces to be
laminated with 0.8 mm laminate of approved shade and make.
15
54
r. ft.
r.ft.
40
12
13
14
15
Cost should also inclusive of paneling, lapping of edges with
plywood to achieve thickness as per design and approval of
Engineer-in-charges.
CREDENZA
Manufacturing and supplying credenza of 4.0’ x 1’-6” x 2’-3”
over all size made with 19mm Plywood (of approved make)
frame work having 15” wide and 5” deep drawers on upper side
and below to drawers, the cupboard unit shall be with folding
shutter & adjustable shelf all along the full width of the
credenza. All drawer shall be fitted with telescopic channels
and automatic push type locking arrangement and cupboards
shall have locking arrangement and all exposed edges of
plywood shall be fitted with teak wood beading duly polished.
All bidding shall have zinc oxide polish of matching color. All
exposed and visible surfaces shall be laminated with 1.5 mm
thick laminate of approved regular shade/ 1.0mm thick laminate
of approved premium shade and all invisible surfaces to be
laminated with 0.8 mm laminate of approved shade. The rates
should include individual locking arrangement (to be operated
by single key) for all drawers and cupboard alongwith best
quality 4” brush steel handles, sliding channel with roller + ball
bearing arrangements etc. complete.
Cost should also
inclusive of paneling, lapping of edges with plywood to achieve
thickness as per design and approval of Engineer-in-charges.
CUPBOARDS / STORAGE UNITS - of 2.75 ft height
Manufacturing, supplying and fixing of box type cupboards /
storage units of required, sizes and as shown in the drawing
and of 1' 6" depth and made out of 19 mm thick Plywood allround and 8 mm Plywood of approved make at the back.
The19mm Plywood shelves / compartments shall be provided
at 15" c/c horizontally and 3' 0" c/c vertically. The unit shall
have hinged type shutters on the front made out of 19 mm
Plywood with approved quality concealed hinges, locks tower
bolts, knobs all as per approved quality. All external surfaces to
be laminated with 1.5 mm thick laminate of approved regular
shade/ 1.0mm thick laminate of approved premium shade and
all internal surfaces to be laminated with 0.8mm thick laminate
of approved shade & make. Front edges of shelves and all
exposed edges of plywood to be leaped with teak wood
finished with polish. Footing to be made of 2.5" x 1.5" teak
wood frame covering all four sides of bottom surface and
covered with 6 mm Plywood of approved make and 1.5 mm
thick laminate of same shade.
CUPBOARDS / STORAGE UNITS - of 4.5 ft height
Manufacturing, supplying and fixing of box type cupboards /
storage units of required, sizes and as shown in the drawing
and of 1' 6" depth and made out of 19 mm thick Plywood allround and 8 mm Plywood of approved make at the back.
The19mm Plywood shelves / compartments shall be provided
at 15" c/c horizontally and 3' 0" c/c vertically. The unit shall
have hinged type shutters on the front made out of 19 mm
Plywood with approved quality concealed hinges, locks tower
bolts, knobs all as per approved quality. All external surfaces to
be laminated with 1.5 mm thick laminate of approved regular
shade/ 1.0mm thick laminate of approved premium shade and
all internal surfaces to be laminated with 0.8mm thick laminate
of approved shade & make. Front edges of shelves and all
exposed edges of plywood to be leaped with teak wood
finished with polish. Footing to be made of 2.5" x 1.5" teak
wood frame covering all four sides of bottom surface and
covered with 6 mm Plywood of approved make and 1.5 mm
thick laminate of same shade.
FALSE CEILING (GYPSUM BOARD)
Supplying & fixing in position false ceiling with 12.5 mm thick
15
no.
200
sq.ft
84
3300
sq.ft
sq.ft
41
gypsum board (flat type) with necessary opening for light
fittings as shown in the drawing for horizontal & verticals fixed
over G.I. framework as specified below by India Gypsum Co.
Ltd.
Ceiling channel (MF5) of size 80 mm x 26 mm x
0.5 mm at every 457 mm center to center. Intermediate
channel (MF7) 15x45x0.9 mm at every 1220 mm c/c.
Perimeter channel (MF6A) 20mm x 26 mm all along the wall.
Strap hanger (MF8) on suspending the frame work 25 x 0.5
mm with nuts and bolts (PS26) 6.4mm x 12.7 mm.Connecting
clip (MF9) of 2.64 mm thick.Dry walls screw of 25 mm
long.Dash fastener / Rawl plug 12.5 mm dia x 35 mm long with
6 mm dia bolt.Soffit cleat 27x37 x 25 mm & 1.6 mm thick.
16
17
18
19
VERTICAL BLINDS
Supplying and fixing of vertical blinds of 'Vista Leveler / Mac'
make or equivalent approved make, made of 100% Woven
Fabrics Vanes (Louvers) in 100mm width, Dust guard, PVC
coated / chemically treated for stain and flame resistance
confirming to M-1, installed with special swivel brackets of 14
gauge galvanized steel facilitating clip-on installation in the
head rail, to be controlled by a polyester braided cord attached
to the leading traveler with 1800 rotation / tilting to be controlled
by an endless ball-chain pulley, which revolves a spine shaft of
corrosion resistant aluminum extrusion, actuating a warm gear
mechanism in each traveler. The head rail shall be of powder
coated aluminum extrusion 25mm x 45mm x 1.2mm thick of
'Hindalco' or equivalent make with a groove for clip-in
installation bracket, with head rail hardware of synthetic
polymer located in by snap-in action and all selection of colour,
pattern and make as approved by Engineer-in-charge.
WOODEN CLADDING (on wooden Frame work & Laminate)
Providing and fixing of wall paneling made out on hollok / sal
wood section, baton frame work. The wood shall be of 2.0” x
1.5 “section and shall be fixed to wall / concrete surface @ 2’
c/c in both horizontal and vertical directions having butt jointed
with rawl plug / guttis and shall be treated with anti termite
treatment. The 12 mm ply wood shall be fixed over the wooden
frame work and finished with 1mm thk premium laminate in two
color of approved shade and as per the design and direction of
the employer. The boxing shall be in 18mm thk plywood and
shall be finished with 1mm thk laminate in two color as per the
design and direction of the employer. The rate shall be
inclusive of all the hardware necessary for the complete
execution of the item as per the design.
GRANITE CLADDING
Providing and laying of 20 mm thick mirror polished granite
slabs of approved shape and size in position at the wall /
column faces and as per the detail shown in the drawing, the
site condition and instructions of the Engineer in Charge. The
granite shall be first quality of telephone black , ruby red /
copper or equivalent approved granite for the design and
contrasting. Stones are to be maintained meticulously as per
the design. The rate quoted should be inclusive of removing
the existing plastering, applying the requisite lair of 1:3 cement
mortar under lay for fixing of granite in position, curing etc. all
complete in all respect. dolls and spikes shall be used to
ensure proper bonding with wall / concrete surfaces etc.
P.O.P. WORK TO WALL / SURFACE
Providing ,applying and fixing the Plaster of Paris to the
plastered/ concrete surfaces of a structure in the thickness as
required as per site condition to make the given surfaces
400
sq.ft
1700
sq.ft
100
sq.ft
1400
sq.ft
42
smooth (as required for fine type of painting work) in perfect
line & dori & plumb with proper finish. The rate shall include
cost of all material, labor, scaffolding, ladders charges, storing
& safeguarding the material etc all complete.
20
21
22
PLASTIC EMULSION PAINTING
Providing and applying Premium emulsion ( water based 100%
acrylic) interior paint to all type of smooth plasters, concrete,
false ceiling etc. surface. The surface to be painted shall be
made free from any loose paint, dust , grease and any fungus,
algae or moss on it shall got be removed/ sand thoroughly by
emery paper 180 and wipe clean. Then one coat of interior
grade wall primer be applied & after which any surface
imperfection such as holes, dents, fine cracks shall be
corrected by filing with acrylic grade wall putty. Thereafter
sand the surface with emery paper 180 and wipe clean and
apply second coat of interior grade wall primer and again
surface imperfection to be corrected. Again sand the surface
with emery paper 320 and wipe clean and then apply the
Premium emulsion in two coats. All materials shall be of Asian/
British or approved make. The color and pattern/ color
combination of the paint shall be got approved from Engineer in
Charge. The stock of the quantity for all material as per
manufacturer’s theoretical consumption (per unit of surface
area) shall be made available at site before commencement of
the painting work. The rate shall include cost of all material,
labor, scaffolding, ladders charges, storing & safeguarding the
material etc all complete.
INTERIOR TEXTURE WORK(ROYALE
5000
sq.ft
500
sq.ft
PLAY – NON METTALIC)
Providing and applying Royale play textured ( non metallic )
work to all type of interior smooth plasters, concrete, false
ceiling etc surface. The surface shall be made free from any
loose paint, dust , grease and any fungus, algae or moss on it
shall got be removed/ sand thoroughly by emery paper 180 and
wipe clean. Then one coat of interior grade wall primer be
applied & after which any surface imperfection such as holes,
dents, fine cracks shall be corrected by filing with acrylic grade
wall putty. Thereafter sand the surface with emery paper 180
and wipe clean and apply second coat of interior grade wall
primer and again surface imperfection to be corrected. Again
sand the surface with emery paper 320 and wipe clean and
there after apply Royale play texture ( non metallic ) with roller/
special effects tools in two coats to achieve the desired effects.
All materials shall be of Asian/ British or approved make. The
color and pattern/ color combination of the paint shall be got
approved in advance from Engineer in Charge. The stock of the
quantity for all material as per manufacturer’s theoretical
consumption (per unit of surface area) shall be made available
at site before commencement of the texture work. The rate
shall include cost of all material, labor, scaffolding, ladders
charges, storing & safeguarding the material etc all complete.
ALUMINUM SLIDING WINDOWS -- two tracks mitered
Providing and fixing in position power coated to the approved
shade aluminum sliding windows of two tracks mitered and
mechanically assembled at corners with frame size of 62 x 45
mm (Bottom frame with gutter section, bottom frame 0.90 kg /
m and top and side frames 0.838 kg/ m) shutters with sections
of 18 mm x 40 mm (Wt 0.56 kg / m ) and interlocking sections
18 mm x 40 mm ( Wt. 0.625 Kg / m ) including 5 mm thick plain
sheet clear glass, glazing clips, rubber / PVC gasket, roller
bearing encased in nylon casing and self locking catch fitted in
vertical section with all other accessories etc. complete.
350
sq.ft
TOTAL
43
44