Guide Specification in CSI format 2014
Panasphere Premium Surfaces Thermally Fused Laminate (TFL) decorative panels are durable,
economical and environmentally responsible. The wide range of surface finishes and textures make
Panasphere’s TFL an excellent choice for residential and commercial applications. The moisture, wear
and stain-resistant properties of the thermally fused surface makes it easy to clean and maintain. For
additional information, please visit our website www.panaspheresurfaces.com or call (626) 363-1077.
Section 066401
Thermally Fused Laminate Decorative Panels - Interiors
Part 1 General
1.1 Summary
A. Provide Thermally Fused Laminate (TFL) decorative panels for wall applications, case-goods and
cabinetry.
1.2 Submittals
A. Product Data: Submit Manufacturer’s literature including product characteristics, accessories
and limitations.
B. Selection Samples: Submit samples of colors and finishes if requested by designer and architect.
C. Verification Samples: Submit samples of materials selected specified to verify color and finish.
D. Industry Certifications and Standards: Submit copy of documentation indicating compliance.
1.3 Quality Assurance
A. Manufacturer: Minimum of 15 years of experience manufacturing similar products.
1.4 Delivery, Storage and Handling
A. Deliver materials and products in manner to protect from damage during transit and storage.
Store and handle in strict compliance with manufacturer’s instructions and recommendations.
1.5 Warranty
A. Manufacturer’s Warranty: Provide manufacturer’s standard warranty against defects in
manufacturing.
Guide Specifications in CSI Format 2014
Part 2- Products
2.1 Thermally Fused Laminate Decorative Panels
A. Manufacturer: Panasphere Premium Surfaces, 18621 E. Gale Ave. City of Industry, CA 91748
USA. Tel: 626-363-1077, www.panaspheresurfaces.com . Panels shall comply with the following:
1. Width/ Thickness: 4’ x 8’ Wide exactly, ¼” (5mm) thick or 4’ x 8’ Wide exactly ¾”
(18mm) thick.
2. Color and Finish: As selected by designer or architect from the manufacturer’s full
range of Panasphere‘s colors and designs.
3.
Part 3- Examination
3.1 Examination- Wall and Surface Preparation
A. Examine substrates for compliance with requirements for installation tolerances and other
conditions affecting performance. Proceed with installation only after unsatisfactory conditions
have been corrected.
3.2 Installation
A. Install product in accordance with manufacturer’s instructions.
1. Inspect for cracking, surface irregularities, damaged drywall and damp areas. Repair
as required before installing.
2. Ensure wall is structurally sound, flat and without bulging, lumps or bumps.
3. Ensure wall is capable of supporting weight of the panels.
4. Ensure surface is free from dirt, grime, grease or loose or peeling materials. If possible
remove any papered materials before application.
5. Ensure wall is thoroughly dry before starting installation.
6. Carefully measure entire height and width of the wall. Recheck to confirm
measurements.
7. Adhesive Method:
a. Panel Preparation: Cut panel into desired dimensions. Apply two strips of heavy
duty double sided tape (this holds the panel in place while the adhesive glue
sets.)
b. Apply the construction adhesive to the panel surface evenly. Be conscious of
drying time. Do not allow the adhesive to set before setting the panel in place.
c. Panel Installation: Starting at the bottom row if the row is parallel to the floor or
skirting, apply the first panel, one panel in from the edge.
d. If the bottom row needs to be cut to shape, start one row up. Then go back to
the first row later and trim. Cut as required.
e. Continue to fix the first row of panels leaving the bottom row edge panels until
last.
f. Align subsequent rows.
g. Use the spacers between the panels to ensure equal spacing and continually
checking with a level so that the panels are being applied to your wall
horizontally and vertically correct and parallel to each other.
h. Install decorative reveal and edge trim, if desired, according to trim
manufacturer’s instructions.
8. Rail and Clip System
Panasphere panels can also be installed using a rail and clip system, which are
conventionally used in commercial applications, and can be easily purchased
though hardware retailers. Follow hardware manufacturer’s instructions.
9. Irregular Spaces: Not all wall corners, floors or ceilings are square. Panasphere panels
can be cut and or edged to match irregular angles.
Create a template and shape your panel. You can make a cardboard template of
the irregular shape and use it to cut the panel prior to fitting. Tip: always
measure twice, then cut. Remember to take into consideration knife thickness
when cutting.
10. Matching edge-banding can be purchased separately to finish any cut edge, if
desired.
3.3 Maintenance and Cleaning
A. Clean with mild household detergent and non-abrasive lint free cloth. Most common stains
should be easily removed. (Note: Avoid using any corrosive chemicals such as bathroom or toilet
cleaners which may permanently damage the surface.) After cleaning wipe off residue with
clean warm water.
B. Avoid contact with sharp or abrasive objects. TFL is designed to be resistant to minor scratches
but can be damaged if excessive force is applied to the surface. Always cover the surface first
prior to placing any sharp objects on the surface.
C. Avoid contact with any hot surfaces. TFL is resistant to heat but prolonged exposure to heat may
cause permanent damage to the surface. Always use a protective pad to minimize the exposure
to heat damage.
End Section