CONTENTS
Product and description ……………………………………………………..…1
Special cautions ………..……………………………………….……………….1
Operation Instructions…..……………………………………….……………….1
Take dispenser out or service.………………………………….……………….2
Attentions …..…………….……………………………………………………….2
Preparation before fist operation..…...…………………………………………2
Electronic controls ………………………..……………………………………..3
Checking possible problems--DIY………………………………………...…….5
Wiring diagram…………………………………………………………….……...6
PRODUCT AND DESCRIPTION
SPECIAL CAUTIONS
* This product belong to the typeⅠhome appliance, this dispenser have to
connect with a three core socket which with a grounding wire. Or use the
electrical leakage protector.
* Please remember do not insert the plug of this dispenser into the socket
which used by some other home appliances or facilities together.
* If do not use the dispenser for long time, please disconnect the dispenser
with the electrical power.
* Do not make any changes on the plug yourself or prolong the power cord
yourself.
* The connecting way of the power cord: X type connecting, if the power cord
get damaged, must be changed by the professional maintenance person, do
not change the power cord by yourself.
* When the water dispenser is working, please do not allow the children play
with the dispenser, to avoid the hurt of the hot water.
OPERATION INSTRUCTIONS
 Operation environmental temperature: 10℃-42℃.
 If the device is not applied for a long time, after the hot water cools down,
please remove the power plug and revolve the backside drainage cap to
drain the rest water in the hot tank then tighten the cap. Open the cold
water faucet to drain the rest water in the cold tank.
 If you do not plan to use the water heating function for more than three
days, we strongly recommend that you turn off the hot water function.
TAKING DISPENSER OUT OR SERVICE
 If the water dispenser will not be used for a long period of time, unplug the
power supply cord.
 Turn off the hot water.
 Drain the water through the faucets.
 Drain the water from tanks by drainage hole from the back of the
dispenser.
ATTENTIONS
 Do not use the bottle with any crack, leakage or holes.
 Do not set “heating” function until water comes out of hot water faucet to
prevent any damage on the heating tube.
 Never set “heating” function when there is no water.
 In the process of using, check the water tray frequently. If the water tray is
full, please pour the water out in time.
 Do not change the set of “cooling” between “ON” and “OFF” in three
minutes and protect the compressor and extend the compressor usage
life.
 This water dispenser is not recommended for outdoor use. Locate the
dispenser vertically and on the flat floor. Please keep the back side of the
dispenser more than 20 cm to the wall or other appliance, to make a better
heating emanating for the condenser of the dispenser.
 Locate the dispenser away from direct sunlight and sources of heat (stove,
heater, radiator, etc.).
 Keep the body of the dispenser clean, avoid the body of dispenser to be
scratched by the hard and sharp things.
 Please do not incline the dispenser more than 45 degrees when move it.
And also when move the dispenser, to avoid dropping and crash.
 Please do not locate the dispenser near the costly appliance or facility, like
the TV, DVD.
PREPARATION BEFORE FIRST OPERATION
 Before connecting the appliance to the power source. Let it stand upright
for approximately 2 hours. This will reduce the possibility of a malfunction
in the cooling system from handling during transportation.
The water dispenser is pre-cleaned at the factory but the reservoir and water
lines must be flushed with fresh water before use as follows:
1. Keep the unit unplugged.
2. Check and make sure the backside hot water drainage hole cap is not
leaked or broken.
3. Fill water tank with tap water full to capacity, wait for 5 minutes until
water settles.
4. Press the hot water faucet button until water comes out, then stop.
5. Plug the dispenser into the electrical socket. Press power ON/OFF
button. We are ready to complete the first cycle. In order to do that, wait
for the hot water to reach temperature (it will indicate ready with 3 beeps)
in approximately 10 minutes, and then wait for the cold to reach
temperature in other 40 minutes approximately (it will indicate ready
with 3 beeps).
6. Unplug the dispenser from the electrical outlet. Proceed to drain the
water from the faucets button, pressing hot water button and then cold
water button, until no more water remains. (to facilitate this operation,
use a large container)
7. Then, drain any water left in the tanks by opening the drain cap (stopper)
locates on the back side of the dispenser, until the left water drains
completely. Please do remember to close the drain cap(stopper) after
the drainage.
8. Then you could place a 5 gallon /3 gallon bottle of water onto the water
intake of the dispenser, allow water to stand for approximate one minute.
Or place a water purifier onto the water intake of the dispenser, then
pour tap water into the water purifier, also allow water to stand for
approximate one minute to let the water flow into tanks.
9. Push water faucet buttons to insure water flows from both faucets.
10. Plug the dispenser back to electrical socket.
11. Now you are ready to use your water dispenser.
ELECTRONIC CONTROL:
For storage/refrigerator cabinet
For sterilization cabinet
1 INSTRUCTION OF LCD
（1）In a Stand-by status: Press ON/OFF button, the screen will be on display
and goes into stand-by status. Press ON/OFF again, the screen will be off.
(2)Heating function:
A). Under Stand-by status, press HOT/+ button. Heating indicator will flash on
the display, heating function starts. When hot water temperature reaches to the
setting temperature, the heating function stops and indicator stops flash and
display steadily. When hot water is 5℃ lower than setting temperature, heating
function will restart till hot water reaches setting temperature.
B). Under heating process, press HOT/+ button, hot water temp. and heating
indicator off, stop heating function.
(3)Cooling function:
A). Under Stand-by status, press COLD/- button. Cooling indicator will flash on
the display, cooling function starts. When cold temperature reaches to the
setting temperature, the cooling function stops and indicator stops flash and
display steadily. When cold water is 2℃ higher than setting temperature,
cooling function will restart till cold water reaches setting temperature.
B). Under cooling process, press COLD/- button, cold water temp. and cooling
indicator off, stop cooling function.
(4)Set function:
A). Under Stand-by status, press SET button. Set function starts. The setting
item flashes on display. The set function includes CLOCK(hour and minute)→
HOT WATER TEMP. →COLD WATER TEMP. as doing recycling.
B). Under every setting status, current setting item flashes on display. Use
HOT/+ and COLD/- to make plus or minus. If not press any button over 8
seconds, the setting will be finished, and that moment setting will be accepted
as system’s setting data. And be out of setting status. Under setting process,
press HOT/+ or COLD/- for 2 seconds more and goes into continuous plus or
minus status.
C). System default hot water setting temperature is 92℃. Hot temperature
setting could be adjusted between 50℃ and 92℃.
D). System default cold water setting temperature is 7℃. Cold temperature
setting could be adjusted between 6℃ and 10℃.
(5)Mute function:
Press STERILIZING/MUTE button over 2 seconds. System enters MUTE
status. Beeper display indicator is off and beeper function stops. Press
STERILIZING/MUTE button over 2 seconds again. System enters BEEPER
status. Beeper display indicator is on and beeper function works. System
default setting is beeper function on.
(6)Ozone sterilization function(for sterilization cabinet only):
Press STERILIZING/MUTE button, ozone sterilization indicator flashes
steadily and sterilizing function starts. Press STERILIZING/MUTE button again,
ozone sterilization indicator is off and sterilizing function stops.
(REMARKS: Under sterilizing function, this function will be paused if door is
opened. Ozone sterilization display indicator is only ON but without flash. After
door is closed, resume sterilizing process and ozone sterilization display
indicator flashes again. Sterilization process is 15 minutes. Don’t open the
door during sterilizing process in case leakage of ozone. Only take out articles
from cabinet 1 hour after sterilizing process is finished. Sterilization cabinet is
only used to keep small articles like paper cup and tea pot.
CHECKING POSSIBLE PROBLEMS—DIY
Following performances are common and normal:
 Under heating process, there is some slight noise and steam from heater.
 Under heating process, when hot water tank has no water inside, water
dispenser stops heating, meantime anti-overheated indicator flashes and
beeper makes noise. Anti-overheated protector cuts off automatically. This
protector could not reset automatically, so customer needs professional
technician to reset it manually.
 If room temperature is higher, cooling speed is slower and cooling process
time is longer. It is common.
 Under ozone sterilization process, there is ozone smell if cabinet door is
opened.
 Low-temperature warm-keeping function: when water dispenser is cooling,
if cold water temperature lower than 3℃, water dispenser stops cooling
automatically, meantime low temperature protection indicator flash(the low
temperature protection indicator is cooling indicator *and ℃ flash
together)please reset the power, then the water dispenser can work
normally.
In case the dispenser get some problems, before you sending the dispenser to the
maintenance place, you may checking the problems by yourself as follows:
Malfunction
phenomena
Possible seasons
Clear the problem
1. The LCD screen
does not display
1. The electrical power has
not been connected well
2. the ON/OFF switch is
not on
2. Big noise when the
dispenser is working
The dispenser is not
located well
3. Press the left water
faucet button, no
water come out
There are some air left in
the hot water tank
4. Press the right
water faucet button,
no water come out
There are some air left in
the cold water tank
5. water leakage from
the head of top cover
The cap of the water bottle Change water bottle.
is damaged
(Contacting your bottle water
supplier.)
1. Check if the plug inserted
into the power socket well
2. Check if the socket
connected with the power well
3. Turn on the switch
1. Make the dispenser be
located on flat fool
2. Do not let the back of the
dispenser lean on the wall
1. Press the left faucet button
till water come out
2. Shake the dispenser gently.
1.Press the right faucet button
till water come out
2. Shake the dispenser gently.
WIRING DIAGRAM
Diagram for Storage Cabinet
Diagram for Sterilization Cabinet
Diagram for Refrigerator Cabinet
This appliance is not intended for use by persons (including children) with
reduced physical, sensory or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or instruction concerning
use of the appliance by a person responsible for their safety.
WARNING-Do not use mechanical devices or other means to accelerate the
defrosting process, other than those recommended by the manufacturer.
WARNING-Do not damage the refrigerant circuit.
WARNING-Do not use electrical appliances inside the food storage
compartments of appliance, unless they are of the type recommended by the
manufacturer.
WARNING-To avoid a hazard due to instability of the appliance, it must be
fixed in accordance with the instructions.
In order to ensure the water dispenser with enough stability, users should
follow below instructions to fix the unit:
1. Remove one of the body rear’s screw (upper right corner or upper left
corner)
2. Install a bracket where you have removed the screw already, fix the bracket
tightening the removed screw on the right location
3. Fix the bracket on the wall side or similar object (if the wall side is too
rigidity), you can make a hole by electric drill, then using expanded screw
tightening the bracket
4.Children should be supervised to ensure that they do not play with the
appliance.
5.Household used only
6.Do not store explosive substances such as aerosol cans with flammable
propellant in this appliance.
7.If the supply cord is damaged,it must be replaced by the manufacturer，its
service agent or similarly qualified persons in order to avoid a hazard.