5 FEBRUARY 2016
MATH 311- LAB 5
ONE-SAMPLE HYPOTHESIS TESTING AND
CONFIDENCE INTERVALS FOR MEANS
DUE: MONDAY, FEBRUARY 25TH AT 3:00 P.M.
In this lab, you will work with descriptive statistics, one-sample hypothesis testing, and
one-sample confidence intervals.
Objectives:
By the end of the laboratory, you will be able to
 Use Minitab to calculate descriptive statistics and interpret the output
 Perform one-sample hypothesis testing using Minitab.
 Calculate a one-sample confidence interval using Minitab and interpret the output.
Scenario:
The average number of children that a woman in the United States will have during her
lifetime was recently reported to be 2.0 by the CDC.
A certain professor, however, believes that families which have children in college are, in
general, larger than the “average” American family. Thus, a simple random sample of 51
students from a university was asked “How many children did your mother have?” The
results are tallied below:
2
3
2
2
8
2
2
3
4
1
2
2
3
2
2
1
3
2
5
4
3
2
3
3
4
2
Number of Children
2
3
2
2
1
2
3
3
3
3
2
2
2
2
3
3
3
3
2
3
4
4
2
2
3
Question 1: The distribution of the average number of children from a sample of 51
mothers should be normal. Draw a picture of a normal curve below. No, I’m not joking.
The mean, median, and mode of this picture should be 2.0 according to the scenario.
Question 2: How should you think our data will relate to the national average? Use a
complete sentence to write your hypothesis. BIG Hint: we have no reason to believe our
data will be any different from the national average.
Question 3: Formulate the null and alternative hypotheses we’ll use to test the
professor’s belief. Clearly define the parameter being tested (i.e. state what μ represents).
Let μ =
H0: μ =
HA: μ
Now enter the data above into a Minitab worksheet. Label the column “Children.”
Question 4: Run the descriptive statistics on the number of children in our sample. Fill
in the blanks below:
n = __________
sample mean = __________
sample median = __________
sample standard deviation = __________
Question 5: Perform a 1-sample t-test on Minitab. The steps are below, if you need
them.
z-test statistic = __________




p-value = __________
Go to STAT>BASIC STATISTICS>1-SAMPLE t.
Select Children to put in the Samples in columns box.
Click Perform hypothesis test and type 2.0 in the Hypothesized mean: box.
Click Options and under Alternative choose the appropriate option (“ not equal
to,” “less than,” etc. (note, the correct option is determined by, and should match,
your alternative hypothesis)).
 Click OK.
Question 6: Interpret the results of the test. Note: when using the Z test, if the observed
significance level (p-value) is less than the chosen significance level (typically 5%), then
we reject the null hypothesis. Otherwise we do not reject the null hypothesis.
We only ever “reject the ‘null’” or “do not reject the ‘null.’” We never “accept the
‘null.’”
Question 7: Compute a 1-sample confidence interval with a 90% confidence level.
The steps are listed below if needed.
90% Confidence Interval:





Go to STAT>BASIC STATISTICS>1-SAMPLE t.
Select Children to put in the Variables box.
Click Options and type 90 in the Confidence level box.
Select not equal from the Alternative menu.
Click OK twice.
Question 8: Now compute 95% and 99% confidence intervals:
95% Confidence Interval:
99% Confidence Interval:
Question 9: Which of the three confidence intervals you just computed had the largest
margin of error?
And now for something not completely different….
Radon is an odorless gas that may concentrate in tightly closed houses. Because it’s
slightly radioactive, there is some concern that it may be a health hazard. Radon
detectors are sold, and university researchers test their accuracy. Each of a sample of 12
detectors was exposed to a known concentration of 105pCi/l of radon for 3 days. Let μ
be the average reading from this concentration in the population of all detectors of a
given type.
We would like to test whether the detectors are accurate, that is
H0: μ = 105
HA: μ ≠ 105
at the significance level 5%.
Open the data set Radon.mtw and perform the appropriate test.
Question 10: Complete the following:
t-test statistic = __________
Question 11: What should we conclude?
p-value = __________