Design of Concrete Structures
CE - 403
Dr Sandip A Vasanwala
Prof, DoCE
SVNIT,Surat
Philosophy of Structural Design
• Conceptual design
• A range of potential structural forms and materials are considered
• Preliminary design
• Simple and approximate hand computations are made
• Assess the viability of various alternative conceptual solutions
• Detailed design
• To conclude comprehensive analysis and calculation for the selected scheme
of design
2
Loading Standards
•
3
•
4
Design of Reinforced Concrete Elements
•Reinforced concrete element is a composite material,
consisting of steel reinforcing bars embedded in concrete.
•Concrete has high compressive strength and low tensile
strength.
•Steel bars resist high tensile stresses but very much
expensive than concrete.
•Economy can be achieved by providing steel in tension zones
5
Elements of a Structure
6
Load Transfer Mechanism
• SLAB
• BEAM
• COLUMN
• FOOTING
• SOIL
7
Limit state method
• In this method, the structure has to be designed to withstand safely
all loads and deformations likely to occur on it throughout its life.
• Designs should ensure that the structure does not become unfit for
the use for which it is required.
• The state at which the structure becomes unfit for use is called a limit
state.
• Design should be based on the characteristics value for material
strength and applied loads.
8
LIMIT STATE METHOD
The working stress method provides structural designs performing
satisfactorily at working loads, but it is unrealistic at the ultimate
state of collapse.
The most efficient method shall include the consideration of
ultimate strength of the structure as well as the serviceability and
durability requirements at the service loads. The limit state method
has evolved to include both the aspects of design.
In the limit state method, a structural component is designed for
safety against collapse load and checked for serviceability at the
working loads.
LIMIT STATE METHOD
A limit state is a state of impending failure beyond which a structure
ceases to perform its intended function satisfactorily, both in terms of
safety against collapse load and serviceability at working loads.
Objectives:
✔ As per IS:456-2000, various limit states will be considered in designed to
ensure safety and serviceability.
✔ The section shall be designed for the most critical limit state and shall
checked for other limit states.
✔ Design shall be based on characteristic strengths and other values.
LIMIT STATE METHOD
I.
Limit states of collapse:
a)
b)
c)
d)
e)
f)
g)
In flexure
In compression
In compression under
uniaxial/biaxial bending
In shear
In bond
In torsion
In tension
II.
Limit states of serviceability:
a)
b)
c)
Limit state of deflection
Limit state of cracking
Other limit states, such as
durability, vibration, fire
resistance, etc.
CHARACTERISTIC STRENGTH
•
•
DESIGN STRENGTH
•
DESIGN LOAD
•
IDEALISED STRESS-STRAIN CURVES
FOR CONCRETE
The stress-strain curve for cement
concrete is prepared with respect
to the compressive stress in the
cube up to crushing stage.
The curve generally remains
parabolic up to a strain of 0.002
and then it becomes straight.
IDEALISED STRESS-STRAIN CURVES
FOR MILD STEEL
•
IDEALISED STRESS-STRAIN CURVES
FOR TOR STEEL
For HYSD bars the yield point is
not easily defined based on the
shape of the stress-strain curve;
hence an offset yield point is
arbitrarily defined at 0.2% of the
strain.
Since these HYSD bars are twisted,
these are also specified as Fe 415
(TOR 40) and Fe 500 (TOR 50).
Deformed bars are provided with
lugs or ribs for enhancing their bond
strength.
CHARACTERISTIC & PERMISSIBLE
STRENGTHS OF DIFFERENT STEELS
Type of reinforcement
(steel bars)
High yield strength
deformed bars
conforming to IS:1109
or Fe 415 grade of
IS:1786-1979
415
415
230
High yield strength
deformed bars of grade
Fe 500 of IS:1786-1979
500
500
275