Chapter 1: Background
Dr. Sachin Patil
Dr. Sachin P. Patil, SP'26
1.1 Why Process Control?
▪ Performance Requirements-
Economic Competition
Regulatory Hurdles
Stronger competition demands Tougher environmental and
tighter product quality
safety regulations impose
specificationsand more
strict operational
profitable plant operation.
constraints.
ProcessComplexity
Highly integrated
processes mean
disturbances can
propagate rapidly, making
plants difficult to operate
safely and efficiently.
2
1.2 Process Dynamics Vs. Process Control
▪ Process Dynamics• The study of unsteady-state or transient behavior.
▪ Process Control• The strategies used to maintain a process at desired conditions.
▪ Key Goals• Safety and Environmental Protection.
• Economic Operation.
• Product Quality.
3
1.3 Classification of Process Variables
Controlled Variables (CVs)
Manipulated Variables (MVs)
Disturbance Variables (DVs)
The process variables we
aim to maintain at a
desired value (the set
point).
The process variables that
can be adjusted to keep
the CVs at their set points.
Process variables that
affect the CVs but cannot
be manipulated.
Examples: Temperature,
Pressure, Composition,
Level.
Typically flow rates.
Examples: Changes in feed
conditions, ambient
temperature, raw material
composition.
4
1.4 Representative Processes
5
1.5 Illustrative Example: Blending system
Assumptions:
1. w1 is constant
2. x2 = constant = 1
(stream 2 is pure A)
3. Perfect mixing in the
tank
Notation:
• w1, w2 and w are mass
flow rates
• x1, x2 and x are mass
fractions of component A
Control Objective:
Keep x at a desired value (or
“set point”) xsp, despite
variations in x1(t). Flow rate w2
can be adjusted for this
purpose.
Terminology:
• Controlled variable (or “output variable”): x
• Manipulated variable (or “input variable”): w2
• Disturbance variable (or “load variable”): x1
6
1.5 Illustrative Example: Blending system
Design Question:
What value of w2 is
required to have x = x
SP ?
Co ntrol Q uestio n:
How do we maintain the
set point when conditions
vary ov er time?
Overall balance:
Component A balance:
• At the design conditions,x = xSP . Substitute Eq. 1-2, x = xSP and
x2 = 1 , then solve Eq. 1-2 for w2 :
7
1.6 Feedback Control (Method 1)
• Strategy: Measure CV (x), compare to SP, and adjust w 2.
•
Advantages:
o
Corrects for any
disturbance
(known or
unknown).
o
Does not require a
perfect process
model.
•
Disadvantage:
•
No corrective
action until
after a
deviation
occurs.
• Proportional feedback control law:
1. where Kc is called the controller gain.
2. w2(t) and x(t) denote variables that change with time t.
3. The change in the flow rate, w2 ( t ) − w2 , is proportional
to the deviation from the set point, xSP – x(t).
8
1.6 Feedforward Control (Method 2)
• Strategy: Measure DV (x1), adjust MV (w 2), before the CV is affected
•
Advantages:
o
Corrects for
disturbances
before the
process is
upset.
•
Disadvantage:
•
Must measure the
disturbance.
•
Does not react to
unmeasured disturbances.
•
Requires a process model
• Feedforward control law (based on eq. 1-3):
x1
w2
9
1.7 Classification of Control Strategies
Table. 1.1 Control Strategies for the Blending System
Method
Measured
Variable
Manipulated
Variable
Category
1
x
w2
FB
2
x1
w2
FF
3
x1 and x
w2
FF/FB
4
-
-
Design change
Feedback Control:
• Distinguishing feature: measure the controlled variable
Feedforward Control:
•
Distinguishing feature: measure a disturbance variable
10
1.8 Information Flow and Block Diagrams
Schematic Diagram: Shows physical connections (pipes, sensors).
Block Diagram: Shows the flow of information/signals.
•
•
1. Compare: The controller
2. Calculate: The controller
3. Actuate:The control
calculates the error:
applies a control law to
valve adjusts the flow
e(t) = x_sp - xrn(t)'.
determine the output 'p(t)'.
'w2(t)'
based
on
the
controller's signal.
Figure 1.6 Block diagram for composition feedback control system on Fig. 1.4.
•
Components:
o
Analyzer (Sensor)/Transmitter: Measures CV and sends signal.
o
Controller: Calculates error and output p(t).
o
Final Control Element: Usually a control valve.
11
1.9 Multi-loop and Multivariable Control
•
Schematic Diagram: Distillation Column.
12
1.9 Multi-loop and Multivariable Control
•
The Pairing Problem:
•
Which MV should control which CV?
13
1.10 The Hierarchy of Control Activities
(days-months)
5. Planning and
Scheduling
(hours-days)
4. Real-Time
Optimization
(minutes-hours)
(seconds-minutes)
3b. Multiv ariable
and Constraint
Control
3a. Regulatory
Control
(< 1 second)
2. Saf ety , Env ironment
and Equipment
Protection
(< 1 second)
1. Measurement
and Actuation
Process
Figure 1.8 Hierarchy of
process control activities.
14
1.11 The Economic Imperative: Reduced Variability
Drives Increased Profitability
Before Improved Control
After Improved Control
15
1.12 The Control System Development
Figure 1.10 Major steps in
control system development
• Traditional Approach:
Experience-based, reactive,
"tuning" in the plant.
• Model-Based Approach
(Recommended): Data-driven,
Proactive, simulation-based.
16
SUMMARY
The Challenge:
Modern industrial processes operate under intense economic, regulatory, and
technical pressures that demand robust control.
The Core Solution:
Fundamental strategies like feedback (reacting to outputs) and feedforward
(anticipating disturbances) provide the building blocks for maintaining stable
operation.
The Path to Mastery:
True mastery comes from scaling these fundamentals within a strategic
hierarchy-from basic regulation to real-time optimization-and using
model-based design to manage complexity and maximize economic
value.
Effective process control is the critical
link between process design and
profitable, safe, and sustainable
operation.
17