UNIT
1
FORCE
Archimedes of Syracuse (287 BC–212 BC) was a Greek mathematician, physicist,
engineer, inventor and astronomer. He is considered as one of the most eminent scientists
and mathematicians of the classical era. He established strong foundations in the field of
mathematics, physics, particularly in statics, hydrostatics and also explained the principle
of the lever. The concept of "center of mass", in the form of the center of gravity, was first
introduced by him.
Key terms and terminologies of the unit
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
Force: Force is defined as the push or pull on a body, which changes or tends
to change the state of rest or uniform motion of a body in a straight line. It is a
vector quantity.
Scalar quantity: A quantity which has only magnitude is called a scalar quantity.
Vector quantity: A quantity which has both magnitude and direction is called a
vector quantity.
Centripetal force: The force on a body moving in a circular path, which is
directed toward the center, is called centripetal force.
Centripetal acceleration: The acceleration of a body in circular motion is called
centripetal acceleration.
Centrifugal force: The pseudo force that balances the centripetal force in uniform
circular motion is called centrifugal force.
Center of gravity: The center of gravity of a body is the point where the whole
weight of the body is supposed to act on the body.
Gravitational field: The region where a mass experiences a force due to
gravitational force is called gravitational field.
Gravitational field intensity: The gravitational field intensity at a point inside
the gravitational field is defined as the gravitational force experienced by a unit
mass placed at that point.
Escape velocity: The velocity of a projected body in space necessary to leave the
gravitational field of a planet or satellite is called escape velocity.
P HYS I CS
Optional Science - 10
0
1
Introduction
We use forces all the time. As we sit on a chair, a downward force is applied on the chair due
to the earth's pull on us. Forces are used in our everyday actions like pushing, pulling, lifting,
walking, pressing. We apply force on the ground while pressing it and while walking. Force
is used when we twist a wet cloth to squeeze out water. Force is defined as the push or pull
on a body, which changes or tends to change the state of rest or uniform motion of a body in
a straight line. It is a vector quantity.
In class nine, you learnt about contact forces and non-contact forces. Friction, upthrust, surface
tension, air resistance are contact forces. Gravitational force, magnetic force and electrostatic
force are non-contact force. In this unit, we look at vectors and scalars, their representation,
addition and subtraction. We will also learn about centripetal force and centrifugal force,
gravitational field intensity, escape velocity and stability of a body.
Physical Quantities
A variety of quantities are used to describe the physical world. For example, distance,
displacement, speed, velocity, acceleration, mass, momentum, energy, work, power. We see
that some of these quantities and processes depend on the direction in which they occur, and
there are some quantities that do not depend on direction. All such quantities can be divided
into two categories. They are scalars and vectors.
Physical Quantities
Vector: A vector is described by
its magnitude and direction. e.g.
displacement (s) = 10 m east
Scalar: A scalar is described by a
number and unit. e.g. mass (m) = 5 kg,
temperature (T) = 273 K, etc.
Scalar quantities
There are some quantities in our world that do not depend on direction. A quantity which has
only magnitude is called a scalar quantity. It is denoted by a number and unit. For example,
length, mass, time, speed, work, energy, temperature. Comparison of scalar quantities depends
only on the comparison of their magnitude. Scalars of the same kind can be added, subtracted,
multiplied or divided by ordinary laws.
Vector quantities
Some physical quantities are described by a magnitude with directions. For example, a
displacement of 1 km to the east, a force of 100N towards centre of the earth, etc. In first
example, 1km denotes 'magnitude' and east denotes 'direction' of displacement. Similarly, in
second example 100 N denotes 'magnitude' and towards centre of the earth denotes 'direction'
of force. Thus, a quantity that has magnitude as well as direction is called a vector quantity.
For example, displacement, velocity, acceleration, force, weight, momentum.
Memory Plus
The necessary condition for a physical quantity to be a vector is that the quantity must
have magnitude and direction.
2
Optional Science - 10
P HYS I CS
Know the Reason
Mass is a scalar quantity, but weight is a vector quantity, why?
Mass is described by magnitude and unit. But weight is a force towards the center of a
planet or satellite. Weight has both magnitude and direction. So mass is a scalar quantity,
but weight is a vector quantity.
Comparison of vectors depends on both magnitude and direction. We cannot add, subtract
and multiply vectors using general algebraic rules. There are special rules to simplify vectors.
They are given a special notation while representing them.
Vector notation
While writing a vector by hand, we use the symbol of a physical quantity with an arrow on
→
top. For example, acceleration is written as a . When printed, it is in bold print as a.
→
The magnitude of a vector is denoted either by the symbol |a | or by the symbol of the vector
written with the regular type as 'a'.
Graphical representation of vector quantities
Graphically
vector
quantities
are
represented by a scaled vector diagram.
The directed line in a vector diagram
represents a vector quantit y. A scaled
vector diagram is shown in the given
figure.
North
West
2.
3.
4
3
Origin
1
2
East
-•..,11----+---1----- (-----'O
A
OA represents displacement of 45m due west
'
South
From the given figures, to represent a
vector we follow following steps:
1.
5
North
The scale is listed.
X
5
A line with an arrow is drawn in a
specified direction.
4
3
The magnitude and direction of the
vector are clearly labelled.
In the first figure, the vector represents a
displacement of 45m towards the west on
a scale of 1cm= 10m.
A
2
1
West
→
30o
East
O
South
In the second figure, the OA represents a force of 5 N in the direction of 30° to x-axis on a scale
of 1 cm= 1N. The length of the line gives the magnitude while the arrow head gives the
direction.
Memory Plus
→
In a vector notation, OA , point O is called the initial point of the vector, and point A is
called the terminal point. The arrowed end of the vector is called the tip, and the other
end is called the tail.
P HYS I CS
Optional Science - 10
3
Differences between scalar quantities and vector quantities
Scalar Quantities
They are expressed in magnitude only.
Vector Quantities
They are expressed in magnitude as well as
direction.
They are denoted by a normal letter like They are denoted by a letter with an arrow
→
time, 't'.
head on its top like acceleration,' a '.
Their addition, subtraction and multiplication Their addition, subtraction and multiplication
is possible using general algebraic rules.
is not possible using general algebraic rules.
They cannot be easily plotted on a graph They can be easily plotted on a graph paper.
paper.
The sum of the scalars is always positive.
The sum of the vectors can be positive,
negative or zero.
Scalar addition
Mass is a scalar quantity. Can you find the resultant of 2 kg and 3 kg masses in your hand? It is
a simple problem for you. Just add each of them to find the resultant. So simple algebraic rules
are used to add scalars. For example, suppose the mass of a boy is 60 kg and that of another
boy is 50 kg. When they sit on a bench, the resultant mass on the bench is given by simple
addition i.e. 60 kg + 50 kg = 110 kg.
Vector addition
The process of obtaining the resultant or sum of the vectors is called addition or composition
of vectors. Vectors cannot be added using the simple rules of algebra applicable to scalars. For
example, we walk first north 20 m (s1) and then east 10 m (s2). We cannot add the magnitude
→
→
→
of s1 and s2 to obtain the resultant displacement. That is, s ≠ s1+s2.
Graphical and analytical methods are commonly used for vector addition.
Graphical addition of vectors or geometric method
The graphical method is a convenient way to describe the rules for adding vectors. Vector
addition can be done easily by this method. This method is also known as the head-to-tail
method. In this method, the vectors are drawn to scale and added by drawing the resultant.
Adding vectors in one dimension
→
→
Two collinear vectors a and b can have different possible direction with respect to each other.
Case1: When the vectors are parallel
→
→
When the vectors a and b are parallel, the magnitude of
their resultant is equal to the sum of the magnitude of both
the vectors. It acts in the same direction of the components.
In vector form, the resultant is given by,
→
→
→
R=a+b
→
→
→
a
+
→
b
=
scale: 1 division = 100m
.- a= 200m,E
b= 400m,E
→
R
+
N
W
E
S
In the given figure, a and b represent two segments of a child's walk. They are added by
→
placing the tail of one vector at the head of the other vector. Here the resultant R is the third
→
vector drawn from the tail of the first vector to the head of the second vector, R = 600m, E.
0
4
Optional Science - 10
P HYS I CS
Example:
A man walks 54.5m east, then another 30m in the same direction. Find his resultant
displacement.
Solution:
54.5m,E
→
+
30m,E
→
Let, a = 54.5m East, b = 30m East
Resultant is given by
→
→
84.5m,E
→
R = a + b = 84.5 m,E
Case2: When the vectors are anti-parallel
When the vectors are anti-parallel, the magnitude of their resultant is equal to the difference
of magnitude of both the vectors. It acts in the same direction of the vector having a greater
magnitude. In vector form, the resultant is given by,
→
→
→
a
b
→ →
R
→
=
R = a + (- b )
In the given figure, a child returns after moving 200m east and
walks 400m west. In this case also the vectors are added head to
tail, and the resultant is drawn from the tail of the first vector to
the head of the last vector. The resultant is equal to 200 m west.
b= 400m,W
Adding vectors in two dimension
R= 200m,W
a= 200m,E
N
W
E
S
We can add non-collinear vectors by the triangle method, parallelogram method and polygon
method.
Triangle method
In the triangle method, if two vectors are there:
I _J
Tail of the first vector a is joined with the tip of the second b . Which
d
gives the resultant R of the two vectors. That is, R = a + b .
→
1.
→
The tail of the second vector b is placed at the tip of the first vector a .
→
2.
→
→
→
→
→
→
b
→
a
→b
→a +
head to tail
→R =
→
Length of R gives the magnitude of the resultant vector and its angle gives the direction
of the vector.
3.
Know the Reason
The graphical method for adding vectors is also called 'head-to-tail method', why?
In the graphical method of adding vectors, vectors can be added by arranging them in such
a way that the tail of the second vector is placed at the head of the first vector and so on. The
→
resultant vector, R is the vector drawn from the tail of the first vector to the tip of the last
vector. So the graphical method for adding vectors is also called the 'head-to-tail method'.
→
A represents the displacement of a student 95m east and B
represents the displacement of 55m north. These two vectors
are added by placing the tail of one vector at the head of the
other vector. The resultant is the vector drawn from the tail of
the first vector to the head of the second vector.
P HYS I CS
scale: 1 division = 10 m
o
,30
m
0
11
R=
B= 55m,90o
Example:
→
A= 110m,0o
Optional Science - 10
5
The scale used is 10m/division. Thus the resultant is given by
→
R = Number of divisions × scale factor = 11divisions × 10 m/ division = 110 m,30o.
→
Here, 30o is the angle made by the resultant with vector A. It is measured with the help of a
protactor.
Example:
→
Draw a diagram to show the resultant of the given vectors, a and b by the
triangle method.
I
b
→
a
→
LY
→
b
R
→
→
→
a
When angle between two vectors is 90°
In such cases, there is formation of a right angled triangle.
We can find the resultant by using the Pythagoras's
→
theorem. Let, PQ represents a displacement of 4m from P
→
to Q towards east.QR represents a displacement of 3m from
Q to R towards north as shown in the given figure. PQR is
a right angled triangle.
Magnitude of the resultant: The magnitude of the
→
resultant PR can be obtained by Pythagoras theorem
as
Q
ts
ni
Q² →
²+
=P
R²
u
=5
→
Q
R
→
P
R
P
PR² = PQ² + QR² (since, h² = p² + b²)
Here, PQ, QR and PR represent the magnitude of the corresponding vectors.
→
Direction of the resultant: The direction of the resultant PR can be obtained by
QR
p
tanθ =
(since, tan θ = )
PQ
b
Here, θ gives the direction of the resultant displacement from the initial point P to the
final point R.
Parallelogram method
→
→
When two vectors A and B are to be added, then we
can use the parallelogram method. In this method,
tails of the two vectors are joined to a common point
and the remaining sides are sketched to determine
the diagonal. The diagonal through the common
→
point of the two vectors gives the resultant, R .
A
A
Example:
→
→
Draw a diagram to show the resultant of vectors a and b by the parallelogram method.
→
a
→
b
→
b
→
R
→
b
→
→
a
a
0
6
Optional Science - 10
P HYS I CS
ii
Polygon method
→
D
1.
Vectors are drawn continuously “tip-to-tail”.
2.
The resultant is drawn from the origin of A to the end of
the last vector
R= →
A+ →
B+ →
C+ →
D
If a number of vectors are there, a geometric construction in the
form of a polygon can be made to add them:
C
→
→
→
→
→
The length of R is measured with the help of a scale, and a
protector is used to find its angle. Use the scale factor to convert
the length to the actual magnitude.
B
→
A
The polygon law of vector addition states that if a number of vectors acting simultaneously at
a point are represented in magnitude and direction by the sides of a polygon taken in the same
order, then the closing side of the polygon taken in opposite order represents the resultant in
magnitude and direction.
Things to remember in the graphical method of vector addition:
1.
The length of each vector must correspond to the magnitude of the vector according to
the scale chosen while plotting them. For example, 1cm=1 m.
2.
When the vectors are shifted while joining the tip to the tail, the direction of each vector
must be parallel to itself.
3.
The vectors in the sum must represent the same physical quantity.
Subtraction of vectors
The concept of vector subtraction is derived from the
→ →
definition of negative vector. The operation A—B is
→
→
defined as the vector sum A + (—B ). That is, if we are
→
→
→
→
given two vectors A and B then to subtract B from A
we need to
→
→
B
→
A
→
1.
determine —B from B .
2.
add vector—B to vector A.
→
→
→
The geometric construction for subtracting two vectors
is shown in the given figure.
→
→
A—B
—B
Example:
→
→
Draw a diagram to subtract the given vector p from q .
→
→
→
p
p
p
=
—
→
q
+
→
=
→
→
p —q
—q
P HYS I CS
Optional Science - 10
→
—q
0
7
Centripetal and centrifugal force
Centripetal force
Activity: Whirling a soft ball
1.
Take a 1.5 meter long string and tie a soft
ball at one end.
2.
Hold another end of the string and whirl
that ball over your head. Does that ball
move in a circular path? Do you need to
pull the string inward in order to keep
the ball in circular motion?
3.
If the string is released when
ball is here, then it goes straight
towards A not towards B.
A
B I
I
\
I
I
I
I
I
I
I
I
I
I
I
\
Release the string from your hand and
let the ball fly off. Does that ball follow
a straight path after releasing the string
from your hand?
Side view
Top view
While whirling a ball from a piece of string, we feel that our hand is being tugged
outward by the stone. We need to exert a force inward to keep the stone moving in a
circular path. If the string breaks, then the stone will move in a straight line tangential
to the original circle. It does not remain in that circular path.
According to the Newton's first law of motion, 'a body in motion continues its state of motion
in a straight line unless an unbalanced force acts on it'. But many things move in circles. Thus,
there must be a force on the bodies in a circular motion, which pulls them out of their straight
paths and makes them turn corners.The force on a body moving in a circular path, which is
directed toward the center, is called centripetal force.
Some examples of centripetal force
1.
While whirling a ball in a circular path, the centripetal force is provided by the tension in the
string.
2.
In satellite motion, the gravitational force between a planet and the satellite provides
the centripetal force needed.
3.
When a car goes around a curve, the friction between the tires and road provides the
necessary centripetal force.
4.
The electrostatic force of attraction between the electron and the nucleus provides the
centripetal force to the electrons revolving around the nucleus.
! .··
;
(
. ---- ~
Centripetal force
~equ1red~ tnng . '-.
tension
,
T= ~v2
T
:/:
\,
1.
....·
8
Optional Science - 10
2.
~
3.)
P HYS I CS
)
centripetal
~'-----fo~ -
4.
- - - - - - atectron
Some characteristics of centripetal force
1.
It is a real force.
2.
Centripetal force is only involved in circular motion.
3.
It is always directed towards the center of a circular path.
4.
As the centripetal force is perpendicular to the direction of motion, work done by it is
zero.
Know the Reason
Centripetal force is a real force, give reason.
The centripetal force is provided by different agencies, like gravitational force,
electromagnetic interaction, nuclear interaction, frictional force, etc. So it is a real force.
Expression of centripetal force
v= rω
The direction of a body moving with constant speed in a circular
track changes continuously. It means the body is in acceleration.
The acceleration of a body in circular motion is called centripetal
acceleration. Its SI unit is m/s2. This acceleration is always directed
towards the center of the circular track.
r
a
m
r
Suppose an object of mass 'm' is moving in a circular path of
radius 'r' at constant speed. The magnitude of the centripetal
acceleration is given by;
v2
r
Since, v = rω, where, 'v' is the linear velocity and 'ω' is the angular velocity of the body.
a=
∴ a = rω2
The centripetal force acting radially towards the center is given by
F= ma =
mv2
= mrω2
r
Memory Plus
The rate of change of angular displacement is called angular velocity. It is denoted by 'ω'.
Its SI unit is radian per second (rad/s).
The centripetal force
1. increases with increasing mass of the object
2. increases with increasing speed of the object
3. decreases with increasing radius of the circular path
Direction of centripetal force and velocity in circular motion
velocity is directed
tengential to the circle
In a circular motion, the centripetal force is directed inwards from the
object to the center of rotation along the radius vector. In such a motion, the
tangent at any point on the circular path gives the direction of velocity. The
velocity of the object and centripetal force are perpendicular to one another.
P HYS I CS
v
a
Force and acceleration
are directed towards
center of the circle.
Optional Science - 10
9
Applications of centripetal force
1.
Bending of a cyclist: A cyclist while going round a curve on a horizontal track has to
bend himself a little from his vertical position, in order to avoid overturning. When he
bends himself inward, then the component of the reaction of the road and the force of
friction combine together to provide him the necessary centripetal force for circular
motion.
2.
Banking of roads: The phenomenon of raising the outer edge of a curved road above
the inner edge for necessary centripetal force to the vehicles to take a safer turn is called
banking of roads. The knowledge of centripetal force is used when designing roads
to prevent skidding on a curved road. The horizontal component of normal reaction
and the force of friction combine together to give the necessary centripetal force that is
needed to make the car go round the curve.
3.
To find the orbital velocity of a setallite: The expression of centripetal force is used
to find the orbital velocity of a satellite around the earth. Earth's gravity provides the
inward force, which keeps the satellite in its orbit. To keep a satellite in an orbit, the
centripetal force is equal to the gravitational force between the satellite and the earth.
This gives the necessary tangential velocity 'v' of the satellite in a particular orbit.
Centrifugal force
Activity: Rotate a bucket with water in a vertical plane at a particular speed, so that
water does not pour. Do you observe that water does not pour? This is due to the balance
between the weight of the water and centrifugal force.
We feel an outward push at sharp turnings when the driver of a vehicle turns it. This is due
to the effect of the centrifugal force. It is actually not a force. It is the tendency of a body to
move in one direction, which causes a body turning around a center to move away from the
center. The pseudo force that balances the centripetal force in uniform circular motion is called
centrifugal force.
Memory Plus
The magnitude of the centrifugal force is the same as the centripetal force, but the
direction is along the radius and directed away from the center of the circle.
mv2
i.e., Magnitude of centripetal force = Magnitude of centrifugal force =
r
Some examples of centrifugal force:
1.
When a ball tied at one end of a string is whirled, the centrifugal force pulls the ball
away from the center of the circle.
2.
Chemicals can be separated in a centrifuge by a centrifugal force.
3.
On a moving merry-go-round, we feel our body being acted upon by a force. Actually
there is no force on the body.
4.
Mud flying off the tires of a vehicle in motion,
10
Optional Science - 10
P HYS I CS
Know the Reason
Centrifugal force is a fictitious force, give reason.
Centrifugal force does not arise due to either gravitational, or electrostatic or nuclear
interaction. It arises due to acceleration of a rotating frame. So centrifugal force is a
fictitious force.
Some characteristics of centrifugal force
1.
It is a factitious force.
2.
It is directed away from the center, along the radius.
3.
It does not have an independent existence.
4.
It is equal and opposite to the centripetal force, but it is not the reaction of the centripetal
force.
Applications of centrifugal force
1.
The knowledge of centrifugal force allowed for the invention of the centrifuge, which
separates particles suspended in a fluid by spinning test tubes at high speed.
2.
The dryer of a washing machine acts on the principle of the centrifugal force. The water
molecules from wet clothes are thrown outward due to the centrifugal force acting on
them.
3.
In order to give a bulge to an earthen pot at its middle, the soft clay used to make such
pots is rotated on a wheel. The centrifugal force acting on the soil particles at the middle
is maximum.
Differences between centripetal force and centrifugal force
I~
I Centripetal force
-1
I Centrifugal force
-
Meaning
The force on a body moving in a The pseudo force that balances the
circular path, which is directed centripetal force in uniform circular
toward the center, is called the motion is called centrifugal force.
centripetal force.
Defined by
Isaac Newton in 1684 AD.
Direction
It is a 'center-seeking' force, i.e., it It is a 'center-fleeing' force, i.e., it acts
acts along the radius and is directed along the radius and is directed away
towards the center of the circle.
from the center of the circle
I_Nature
Christiaan Huygens in 1659 AD.
-
-
I
It is a real force.
J
It is a fictitious force.
Center of gravity
Have you ever seen a man carrying a ladder on his shoulder? How does he adjust the length
of the ladder on either sides of his shoulder to balance the ladder? He tries to find the point
where the whole weight of the ladder is supposed to act. He keeps that point of ladder over
his shoulder. That point is the center of gravity of the ladder. The center of gravity of a body is
the point where the whole weight of the body is supposed to act on the body.
P HYS I CS
Optional Science - 10
11
We can completely describe the motion of any object through space in terms of the translation
of the center of gravity of the object from one place to another and the rotation of the object
about its center of gravity if it is free to rotate. In flight, both airplanes and rockets rotate about
their centers of gravity. A kite, on the other hand, rotates about the bridle point. But the trim of
a kite still depends on the location of the center of gravity relative to the bridle point, because
for every object the weight always acts through the center of gravity.
Locating center of gravity
The center of gravity can be located within or outside the body depending on the body’s
configuration and position. In case of a body with mass distributed uniformly throughout it,
the center of gravity (CG) can be determined simply by finding the geometrical center. But it is
a complicated procedure to find the center of gravity when the mass of a body is not uniformly
distributed throughout the object.
1.
For regular and uniform objects
In the case of regular and uniform objects, the
center of gravity is at the geometric center. If
the object has a line (or plane) of symmetry, the
CG lies on the line of symmetry. In the given
diagrams, 'G' represents their center of gravity.
2.
For general shaped objects
CD~
''
.
.·-_
. :J . ..
,. ..
.
I
-:. •
!
••
•
fig: center of gravity of regular objects
In the case of a general shaped object, the center of gravity is determined by some
simple mechanical ways:
i. By finding the balancing point
In this method we just balance the object using a string or an edge, the point at which
the object is balanced is the center of gravity.
ii. By suspending objects:
Activity: To find the center of gravity of an irregular object
1.
Drill a small hole at one end of the object and hang
it up so that it can swing freely.
2.
Hang a plumb-line (a piece of string with a weight
hanging from it) on the same suspension point.
3.
When the object comes to rest, use a plumb-line to
draw a vertical line on it.
4.
Drill another hole at a different location within
the object. Hang it again and repeat the above
procedure to draw another line on the object. Do
you find a point of intersection of the two lines?
Plumb-line
Hang from here
center of gravity
fig:center of gravity of irregular objects
The point where the two lines cross is the center of gravity.This procedure works well
for irregularly shaped objects that are hard to balance.
Center of gravity and stability
Stability refers to the ability of a body to come back to its original equilibrium when it is
slightly displaced. The position of the center of gravity of an object affects its stability.
0
12
Optional Science - 10
P HYS I CS
Conditions for stability: To make a body more stable
1.
Lower its center of gravity:The lower the center of gravity (CG), the more stable an
object. A higher center of gravity increases the probability of the object toppling over.
2.
Increase the area of base: In the case of a wider base, the center of gravity remains
inside its base and does not topple easily.
Real life applications
1.
The luggage compartment of a tour bus is located at the bottom rather than on
the roof.
2.
Extra passengers are not allowed on the upper deck of a bus.
3.
Table fans, table lamps are designed with a larger heavy base.
4.
The center of a building is lowered if much of the structure is below the ground.
5.
A tall object with a narrow base, such as a bookcase, will have a high center of
gravity and thus only a small force applied towards the top of the object can
topple it over.
6.
Racing cars are built low and broad.
Center of gravity and stability of a vehicle:
1.
Empty vehicle can be unstable
The heaviest part of an empty vehicle is not at the center of the vehicle. It lies in the
engine compartment. The center of gravity is not well supported. The front axles bear
most of the weight. That’s why an empty vehicle can be unstable.
When a load as heavy as the engine is added in the vehicle, then the center of gravity
shifts somewhere around the front half of the cargo area. In such a condition, each axle
is supporting an equal amount of weight. The vehicle is stable.
If the cargo is heavier than the engine of the vehicle, then the center of gravity of the
whole load is towards the rear of the vehicle. The vehicle in not stable in this condition,
too.
2.
Buses are built closer to the ground
Buses are shorter in height and built lower to the ground than trucks. This makes them
more stable as their center of gravity is lowered. However,a double-decker bus has a
higher center of gravity and presents a driving challenge.
Know the Reason
Buses are more stable than trucks, why?
As buses are built closer to the ground, the weight is distributed throughout the vehicle
body. The load of passengers is not likely to have a high center of gravity. The center of
gravity is well supported even in an empty bus. So the buses are more stable than trucks.
A Formula 1 car is very stable, and a large force must be applied to topple it, why?
To make a body more stable, we need to lower its center of gravity and increase the area
of its base. A Formula 1 car is also made with a wide base and low height. So a Formula 1
car is very stable, and a large force must be applied to topple it.
P HYS I CS
Optional Science - 10
13
3.
Vehicles that are too tall are unstable
When a load is added to a greater height, the center of gravity shifts towards the roof.
That is called a high center of gravity. On a level road, it is not a serious problem, but
on a banked road, the body of the vehicle tilts away from the high side of the bank. The
center of gravity is no longer over the center of support. It is away from the central line.
The vehicle is unstable. A vehicle carrying even a legal amount of weight can be unsafe
due to the center of gravity problem.
Gravitational field
A mass exerts force on another mass kept at a certain distance. This is due to the gravitational
field around a mass. The gravitational field of a material body is the space around the body
in which any other mass experiences a force of attraction. For example, the earth produces a
gravitational field around itself and then exerts force on the object inside that field. The region
where a mass experiences a force due to the gravitational force is called gravitational field.
The effect of the gravitational field decreases as the distance from the body is increased. This
distance depends on the mass of the body.
Gravitational field intensity
The gravitational field of a planet or satellite has a different magnitude at a different point. The
exact effect of the gravitational force at a point in the gravitational field is measured by
gravitational field intensity. The gravitational field intensity at a point inside the gravitational
field is defined as the gravitational force experienced by a unit mass placed at that point.
Memory Plus
Gravitational field intensity is a vector quantity and its direction is the same as that of
the gravitational force.
Let us consider a test mass of 'm' at a point 'P'. It is at a distance of 'r' from the center of the
planet having mass 'M' and radius 'R'.
According to Newton's universal law of gravitation, the gravitational
force is given by
GMm
r2
Where 'G' is the universal gravitational constant whose value is equal
to 6.67×10-11 Nm2kg-2.
F=
h
m
R
r
P
M
The gravitational force experienced by a unit mass at P is the
gravitational field intensity at that point. It is denoted by 'I' and given by
GMm
F
r2
I = - == m
m
GM
...
I= 2
r
It is directed towards 'M'.
The SI unit of gravitational field intensity is Nkg-1 and CGS(centimeter-gram-second) unit is
dyneg-1.
14
Optional Science - 10
P HYS I CS
A Special Case:
When r = R, i.e., the object is on the surface of a planet,
GM
R2
This means that the gravitational field intensity on the surface of a planet is equal to the value
of acceleration due to gravity, i.e., I= g.
Gravitational field intensity, I=
For example, the gravitational field intensity on the earth
at the pole, IP = 9.83 Nkg–1
at the equator Ieq = 9.78 Nkg–1.
Memory Plus
The weight of a body of mass 'm' at a place where the gravitational field intensity is 'I'
is given by
W = Mass (m) × Gravitational field intensity (I)
Solved numerical
1.
The mass of the moon is 7.2× 1022 kg and its radius is 1.7× 106 m. Find the gravitational
field intensity on its surface. What is the weight of a body of mass 100kg on its surface?
(G = 6.67 × 10-11 Nm2/kg2)
Solution:
Here, mass of the moon (M) = 7.2 × 1022kg
Radius of Earth (R) = 1.7× 106m
The gravitational field intensity (I) due to the moon of mass M and distance R from its
center is given by
GM
R2
6.67 × 10–11 × 7.2 × 1022
I=
1.7× 106 × 1.7× 106
48.02 × 1011
I=
2.89× 1012
16.7
I=
10
I = 1.67 N/kg
I=
Or
Or
Or
Therefore, the gravitational field intensity on the surface of the moon is 1.67 N/kg.
Now, the weight of a body of mass 100kg on its surface is given by
W = Mass× Gravitational field intensity
Or, W = 100× 1.67 = 167 N
Therefore, the weight of a body of mass 100kg at its surface is 167 N.
P HYS I CS
Optional Science - 10
0
15
Escape velocity
According to the old concept, “what goes up,
must come down”. But while thinking about
gravity, Isaac Newton developed the concept of
an orbit around the earth, in which a projected
object from the earth can revolve. He imagined a
cannon on top of a tall mountain. When we fire a
cannon, the ball travels horizontally for a short
way before falling to the ground. The next time Escape velocity
when we fire it at a faster speed, the ball travels
further before falling. As the earth is spherical,
Orbital velocity
there must be a speed at which the ball would
keep travelling horizontally and falling towards the earth's surface but never actually hit it. If
the velocity of the projection is equal to the orbital velocity (i.e., 7.1 km/s), then it will go round
the earth in an orbit. Firing the cannon ball with even greater speeds results in elliptical orbits.
Memory Plus
Luna 1, launched as part of the Soviet Luna program in 1959, was the first man-made
object to attain escape velocity from Earth. It was the first spacecraft to reach the vicinity
of the earth's moon.
If an object is thrown upward from the earth's surface, its velocity decreases due to the
downward force of gravity. Such effect is within the earth's gravitational field. The height
which will be attained by an object like a rocket after being launched from the earth's surface
depends on the speed with which it is projected. The greater the speed, the greater the
height. For instance, imagine an experiment where a cannon shoots straight upward instead
of shooting sideways. Each time more gunpowder is added, the cannonball will travel to a
greater height and take longer to come back down. If an object is projected upward from the
earth's surface with such a high velocity that it can escape the gravitational pull of the earth,
then it does not return towards the earth. In such a condition, the object has sufficient initial
kinetic energy to overcome the earth's gravitational pull. The necessary velocity of a projected
body in space to leave the gravitational field of a planet or satellite is called escape velocity.
Expression for escape velocity
Suppose an object of mass ‘m’ is projected vertically upward from the earth’s surface. The
mass of the earth is ‘M’ and its radius is ‘R’.
For an object to escape from the earth’s gravitational pull, work has to be done against the
gravitational force. In such a condition, the initial kinetic energy of the object is due to the
work done against the gravitational force.
i.e.
Kinetic energy = Work done against gravitational force
1
Or
mv 2 = Gravitational force × displacement
2 e
Where ve is the escape velocity. The displacement is equal to the distance between the center
of the earth and the projected object on the earth's surface, which is the radius of the earth, R.
16
Optional Science - 10
P HYS I CS
Or
Or
Or
1
GMm
mv 2 =
×R
2 e
R2
2GM
ve2 =
R
2GM
ve =
R
GM
ve = 2 ×
×R
R
F
✓
v = r2gR Or
e
(since, g=
GM
)
R2
Substituting
Mass of the earth ‘M’ = 6×1024 kg
Radius of the earth ‘R’ = 6400 km = 6.4×106 m
2GM = 2 × 6.67 × 10–11 × 6×1024
R
6.4×106
13—6
80.04× 10
Or
ve = ✓-6.4
ve = 11,183.134 m/s ~ 11.2 km/s
F--
ve =
The escape velocity of an object on the earth is 11.2 km/s or about 7 miles/s.
Factors which determine escape velocity
The expression to find the escape velocity on a planet or satellite is given by
2GM =
2gR
R
Where ‘M’ is the mass of the planet and ‘R’ the radius of the planet. Thus, escape velocity
depends upon
ve =
1.
mass of a planet/satellite (M)
2.
radius of the plant/ satellite (R)
Memory Plus
From the expression of escape velocity, the escape velocity is independent of the mass
of the body and direction of the projection. It depends on the mass and the radius of the
planet from which it is being projected.
The velocity of escape from the earth at its surface is about 7 miles (11.2 km) per sec,
or 25,000 miles per hr; from the moon’s surface it is 1.5 miles (2.4 km) per sec; and for
a body at the earth’s distance from the sun to escape from the sun’s gravitation, the
velocity must be 26 miles (41 km) per sec.
Trajectory of a body when it attains escape velocity
If an object attains escape velocity, but is not directed straight away from the planet, then it
will follow a curved path. Such a path is not a closed path like that of the moon to revolve
around the earth. It is an open curve. That is, a parabola or hyperbola.
P HYS I CS
Optional Science - 10
0
17
1.
If an object attains escape velocity, then the shape of the trajectory will be a parabola,
whose focus is located at the center of the mass of the planet. An actual escape path is
called an escape orbit.
2.
If the body has a velocity greater than the escape
velocity, then its path will form a hyperbolic
trajectory, and it will have an excess hyperbolic
velocity, equivalent to the extra energy the body
has.
Without any other force except gravity, the speed at any
point in the trajectory will be equal to the escape velocity
at that point. In the solar system, a rocket that travels at
escape velocity from Earth will not travel to an infinite
distance because it needs an even higher speed to escape
the sun's gravity.
Parabola, v= ve
Ellipse,
vc< v< ve
Hyperbola, v>ve
Circle,
v=vc
Ellipse,
v<vc
Circular velocity vc = 7.9 km/s
Escape velocity ve= 11.2 km/s
Answer writing skill
1.
I
What is the direction of the instantaneous velocity of a stone going around a circular
path?
The instantaneous velocity of a stone going around a circular path is tangential to the
circle.
2.
Write the condition in which the gravitational field intensity is equal to the value of
acceleration due to gravity.
On the surface of a planet or satellite, the gravitational field intensity is equal to the
value of acceleration due to gravity.
3.
What is the value of gravitational field intensity at pole and equator of the earth?
The gravitational field intensity at the pole, IP = 9.83 Nkg–1 and at the equator Ieq = 9.78
Nkg–1.
4.
What are the two factors which affect escape velocity?
The escape velocity depends upon
5.
1.
mass of a planet/satellite (M)
2.
radius of the plant/ satellite (R)
In which condition does the block shown in the given figure topple over? Give reason.
The block topples over in the second case. In the first figure, the
A
B
block is slightly above the table. Its center of gravity is inside the
base. The block's weight produces an anti-clockwise moment,
and the block falls back to its original position. In the second
figure, the block is tilted far enough. Its center of gravity is beyond the base. The block's
weight produces a clockwise moment and topples it over.
0
18
Optional Science - 10
P HYS I CS
6.
Draw a vector diagram for the displacement of 5m, 30o north of east.
Scale factor= 1m/cm
North
X
4
3
5 ~.,•·
A
..-·
2
1
West
30o
East
O
South
7.
Find the gravitational field intensity at a height of 3,600 km from the surface of the earth.
The radius of the earth is 6,400 km and its mass is 6 × 1024 kg.
Solution: Here, the mass of the earth (M) = 6 × 1024 kg
Radius of the earth (R)=6,400 km
Height from the earth surface (h) = 3,600 km
Distance from the center of the earth (r) = 6,400km+ 3,600 km = 10,000,000m = 107 m.
The gravitational field intensity at a distance of 'r' from the center of the earth is given by
GM
r2
6.67 × 10–11 × 6 × 1024 40.02 × 1013
Or
I=
=
(107)2
1014
40.02
Or
I=
= 4.002 N/kg
10
Therefore, the gravitational field intensity at a height of 3,600 km from the center of the
earth is 4.002 N/kg.
8.
I=
Show that the gravitational field intensity at a test point is inversely proportional to
1
r
Let us consider a test mass of 'm' at a point 'P'. It is at a distance
of 'r' from the center of a planet having mass 'M' and radius 'R'.
the square of its distance from a planet or satellite. i.e., I oc - 2
According to Newton's universal law of gravitation, the
gravitational force is given by
GMm
r2
Where 'G' is the universal gravitational constant whose value is
equal to 6.67×10-11 Nm2kg-2.
F=
h
m
R
r
P
M
The gravitational force experienced by a unit mass at P is the gravitational field intensity
at that point. It is denoted by 'I' and given by
GMm
F
GM
r2
I = ==
= 2
m
r
m
Here 'G' is a constant and 'M' is also constant for a particular planet or satellite.
1
Hence, I oc 2
r
P HYS I CS
Optional Science - 10
0
19
Exercise
Step
1.
1
Define
1. force
2. scalar quantity
3. vector quantity
4. centripetal force
5. centrifugal force
6. angular velocity
7. centripetal acceleration
8. center of mass
9. center of gravity
10. gravitational field
11. gravitational field intensity 12. escape velocity
2.
Very short answer questions
1.
Write the SI unit and CGS unit of force.
2.
Write the relation between the SI unit and CGS unit of force.
3.
What is a negative vector?
4.
Write the SI unit and CGS unit of gravitational field intensity.
5.
Give any four examples of scalar quantity.
6.
Give any four examples of vector quantity.
7.
What is center of gravity?
8.
What is meant by stability of a body?
9.
Write the SI unit of angular velocity and centripetal acceleration.
10. What is the formula used to calculate centrifugal force?
11. What is the value of the escape velocity on the earth’s surface?
12. What was the first man-made object to attain escape velocity from the earth?
20
Optional Science - 10
P HYS I CS
Step
3.
4.
5.
6.
2
Short answer questions
1.
How is the magnitude of vector quantity denoted?
2.
How is a vector quantity represented graphically?
3.
Write the direction of centripetal force and velocity in circular motion.
4.
Write four characteristics each of centripetal force and centrifugal force.
5.
Write any two examples each of centripetal force and centrifugal force.
6.
Write any two applications each of centripetal force and centrifugal force.
7.
Write two conditions for the stability of a body.
8.
Write any four real life applications of the center of gravity in the stability of a
body.
Differentiate between
1.
Vector quantity and scalar quantity
2.
Centripetal force and centrifugal force
3.
Gravitational field and gravitational field intensity
Give reasons
1.
Distance traveled is called a scalar quantity, but displacement is called a vector
quantity.
2.
Mass is called a scalar quantity, but weight is called a vector quantity.
3.
The graphical method for adding vectors is also called 'head-to-tail’ method.
4.
Centripetal force is a real force.
5.
Centrifugal force is a fictitious force.
6.
A ship carries ballast in its hull.
7.
The bottom of a hydrometer is made heavier.
8.
A half-filled mineral water bottle is more stable than a full one or an empty one.
9.
An empty vehicle can be unstable.
10.
Buses are more stable than trucks.
11.
Vehicles that are too tall are unstable.
12.
Escape velocity is the same for all objects projected in any direction.
Answer the questions with the help of the given figure
1.
The center of gravity of three trucks parked on a
slanted road is shown in the given figure. Which
truck will topple over?
P HYS I CS
Optional Science - 10
21
2.
Plot the given vectors on a graph and find their resultant using graphical method.
YL ~
A / , _ 27.5m
\
B
~
8 - 30.0m
o
X
Step
3
7.
Numerical problems
1.
Find the magnitude and direction of displacement which has an x-component of 40m
and y-component of 60m.
2.
A man walks 40m east and then 30m north. Find his resultant displacement.
[Ans: 50m, 37o north of east]
→
→
3.
Vector A is 3m in length and the position is along the positive x-axis. Vector B is 4m in
length and points along the y-axis. Find the resultant vector.
[Ans: 5m, 53.13o with x-axis]
4.
The mass of the moon is 7.2× 1022 kg and its radius is 1.7× 106 m. Find the gravitational
field intensity on its surface. What is the weight of a body of mass 100kg on its surface?
(G = 6.67 × 10-11 Nm2/kg2)
[Ans: 1.67N/kg, 167 N]
5.
The mass of the earth is 6.0 × 1024 kg and its radius is 6.4 × 106 m. Find the gravitational
field intensity at its surface. What is the weight of a body of mass 100kg on its surface?
(G = 6.67 × 10-11 Nm2/kg2)
[Ans: 9.77 N/kg, 977 N]
6.
The mass of the planet Jupiter is 1.9× 1027 and its radius is 7.1× 107 m. Find the gravitational
field intensity on its surface and calculate the weight of a body of mass 90kg on its
surface?
[Ans: 24.14 N/kg, 2172.6 N]
7.
Find the gravitational field intensity at a height of 3,600 km from the surface of the earth.
The radius of the earth is 6,400 km and its mass is 6 × 1024 kg. [Ans: 4.002 N/kg]
8.
Find the gravitational field intensity at a height of 6,400 km from the surface of the earth.
The radius of the earth is 6,400 km and its mass is 6 × 1024 kg.
[Ans: 2.443 N/kg]
9.
What will be the gravitational field intensity of the earth if its mass could be squeezed to
the size of the moon? (Me= 6 × 1024 kg, Rm= 1.7× 106 m)
[Ans: 138.4 N/kg]
8.
Draw a diagram
1.
2.
3.
to show the triangle method of vector addition.
to show the parallelogram method of vector addition.
to show the polygon method of vector addition.
4.
to show the center of gravity in the following regular objects
a. circular disc
d. rectangular bar
0
22
Optional Science - 10
b. rectangular sheet c. triangular sheet e. cuboid
P HYS I CS
Step
1.
4
Derive the following expressions, where the terms used have their usual meaning.
F
mv2
GM
2GM
b. I= 2
c. ve =
r
r
R
State the triangle law of vector addition and derive expressions for the resultant
magnitude and direction.
a. F =
2.
3.
State the parallelogram law of vector addition and derive expressions for the resultant
magnitude and direction.
4.
Explain the mechanical way to determine the center of gravity.
5.
Explain the role of the center of gravity in the stability of a vehicle.
Multiple choice questions (MCQs)
1.
Who defined centripetal force?
a. Christiaan Huygens
c. Charles Darwin
2.
The escape velocity on the earth’s surface is
a. 11,200m/s b. 11,400m/s
b. Isaac Newton
d. Michael Faraday
c. 12,100m/s d. 11,800m/s
3.
The value of the universal gravitational constant is equal to
a. G = 6.67× 10-11 Nm2/kg2 b. G = 6.67× 10-12 Nm2/kg2
c. G = 6.78 × 10-11 Nm2/kg2 d. G = 6.78× 10-11 Nm2/kg2
4.
The gravitational field intensity on the surface of a planet of mass 'M' and radius 'R' is
given by
GM
GMm
b. I=
R2
r2
GMm
GMm
c. I=
d. I=
(r+h)2
R2
a. I=
5.
The value of the gravitational field intensity at the earth’s poles is
a. 9.78 N/kg b. 9.87 N/kg
c. 9.83 N/kg d. 9.38 N/kg
6.
The centripetal acceleration of a body moving with an angular velocity 'ω' in a circular
path of radius 'r' is given by
a. a = rω b. a = rω2
c. a = r2ω2 d. a = r2ω
P HYS I CS
Optional Science - 10
0
23
7.
The expression to find the centripetal force on a body of mass 'm' moving with a velocity
of 'v' in a circular path is
a. F =
mv
mv2
b. F =
r
r
mv2
mv
d. F =
r²
r²
The escape velocity on a planet of mass 'M' and radius 'R' is given by
c. F =
8.
9.
F
F
a. ve =
GM b. v =
e
R
c. ve =
2GM d. v =
e
R
F
F
GM
R²
2GM
R²
The escape velocity depends on which of the following factors
a. mass of the object b. mass of the plane
c. angle of projection d. temperature of the planet
10.
The mass of Jupiter is about 319 times that of the earth and its radius is about 11 times
that of the earth. The ratio of the escape velocity on Jupiter to that on the earth is
a.
c.
29
b. 29
1
1
d.
29
29
r
Project Work
1.
Take a 15 cm scale and 30 cm scale. Balance them on your figure as shown in the given
figure. Do you find the balancing point exactly at half of the length? Mark that position.
Now put that scale over a pointed support in such a way that the mark rests over the
support. Then balance that scale. Do you find the location of the center of gravity of your
scale? Mark that point and show it to your friends in the classroom.
2.
Take a piece of plywood. Make a hole near the edge of the plywood and hang it on a
nail in such a way that the wood can rotate freely about the nail. Make a plumb line by
tying a weight to a piece of string. Hang the string on the nail, and mark the vertical line
with a pencil when the wood comes to rest. Make another hole at some other spot near
the plywood's edge and repeat the same procedure. The spot where the two lines cross
is the center of gravity. Put that plywood over a pointer object. Adjust the position of
the pointed object at the point of intersection of the two lines. Does your plywood get
balanced at that point?
24
Optional Science - 10
P HYS I CS
UNIT
2
PRESSURE
Daniel Bernoulli (February8,1700- March 17, 1782) was a Swiss mathematician and
physicist and was one of the many prominent mathematicians in the Bernoulli family. Daniel
was sent to Basel University at the age of 13 to study philosophy and logic. He finished his
baccalaureate examinations in 1715 and went on to obtain his master's degree in 1716.
The most important work which Daniel Bernoulli did while in St Petersburg was his work
on hydrodynamics. He published the basic properties of fluid flow, pressure, density and
velocity, and gave the Bernoulli principle. One of the most common everyday applications of
Bernoulli's principle is in airflight.
Key terms and terminologies of the unit
1.
Pressure: The force acting perpendicularly per unit area is called pressure, i.e.
2.
Force
.
Area
Fluid: Any substance which can flow and does not possess its own shape is called
fluid.
3.
Thrust: The force which acts normal to a given surface is called thrust.
4.
Liquid pressure: The liquid thrust per unit area on the walls of the container is
called liquid pressure.
5.
Intermolecular force: The force of attraction or repulsion between molecules is
called intermolecular force.
6.
Cohesive force: The force which attracts liquid molecules to each other is called
cohesive force.
7.
Adhesive force: The force which arises between liquid molecules and the
molecules of the container is called adhesive force.
8.
Surface tension: It is defined as the force per unit length acting perpendicular on
an imaginary line drawn on the liquid surface, tending to pull the surface apart
along the line.
9.
Viscous force: The internal frictional force exerted between liquid layers in
motion is called viscous force.
Pressure =
P HYS I CS
Optional Science - 10
25
10.
Viscosity: The property of fluids to offer resistance to objects moving through
them is called viscosity.
11.
Deforming force: The external force which produces change in length, volume
and shape of a body is called deforming force.
12.
Deformed body: A body which experiences a deforming force is called deformed
body.
13.
Restoring force: A force developed within a body which restores the body to its
original state is called restoring force.
14.
Elasticity: The property of a material to regain its original state when the
deforming force is removed is called elasticity.
15.
Elastic body: The body which possess the property of elasticity is called an elastic
body.
16.
Perfectly elastic body: A body which completely regains its original shape and
size after the removal of the deforming force is said to be perfectly elastic.
17.
Plastic: Bodies which do not exhibit the property of elasticity are called plastic.
18.
Perfectly plastic: Bodies which do not exhibit the property to return to their own
shape and size after removing the deforming force is called perfectly plastic.
19.
Plasticity: The property of a body by virtue of which it tends to retain the altered
shape and size on removal of the deforming force is called plasticity.
20.
Partially elastic: The bodies which partially regain their original form after
removing a deforming force are called partially elastic.
21.
Elastic limit: The maximum stress that a piece of material can withstand without
being permanently deformed is called elastic limit.
22.
Stress: The restoring force developed per unit area of a deformed body when
subjected to an external deforming force is known as stress.
Introduction
You had learnt already in the lower classes that the force acting perpendicularly per unit area
is called pressure. It is a scalar quantity. Its SI unit is N m-2 or pascal (Pa). Pressure is the most
important variable in our daily life. In grade 9, you learnt about pressure and some of its
consequences.
Any substance which can flow and does not possess its own shape is called fluid. The fluid
include all liquids and gases. In this chapter, we will learn about some fluid properties,
especially liquid pressure and its flow. The force of attraction between like molecules in a
liquid and that in between unlike molecules of a liquid and the container gives rise to the
surface phenomena in liquids. One of the important surface phenomena in liquids, surface
tension, is discussed in this unit.
Matter is made up of atoms or molecules. Solids have definite shape and appreciable stiffness
or rigidity. Some solids have a property to regain their shape and size after deformation within
a limit. Such a property is called elasticity. In this unit, we will learn about deforming forces,
elasticity and elastic limit, too.
0
26
Optional Science - 10
P HYS I CS
Liquid pressure
Liquids do not maintain a fixed shape. They occupy space in a container and gain shape of
the container. When a liquid is kept in a container, it exerts a force on its walls. In liquids at
rest, force simply acts normal to the surface. The force which acts normal to a given surface is
called thrust. Liquid applies thrust on the walls of the container, which causes pressure on the
container. The liquid thrust per unit area on the walls of the container is called liquid pressure.
Liquid also exerts pressure on any object in the liquid.
Expression for liquid pressure
Let us consider a regular container having area of cross-section 'A',
density of liquid be ' ρ', height of the liquid column or depth be 'h'
and acceleration due to gravity be 'g'.
Volume=Ah
A
Since the thrust at the bottom of the cylinder is the same as the weight
of the liquid. Therefore, the pressure on the base of the container is
given by
A
Force Weight of liquid (W) mg
Pressure (P)
=
=
=
Area
Area
A
Vρg
=
[Since mass of a liquid (m) = volume of liquid (V) × density (ρ)]
A
Ahρg
=
[Since volume of liquid (V) = area of cross section (A) × height (h)]
A
Pressure (P) = hρg
Thus, the pressure at a point inside a liquid is given by the product of the depth, density of
liquid and acceleration due to gravity.
Factors on which the pressure at a point in liquid depends
The pressure due to a liquid depends on three factors- depth of liquid, density of liquid and
acceleration due to gravity.
1.
At a particular place, the acceleration due to gravity (g) is constant. When the acceleration
due to gravity (g) and density of the liquid (ρ) are constant, the pressure in a liquid is
directly proportional to its height. i.e., P α h (keeping 'g' and 'h' constant)
For example, the height of a water column in a tap on the upper floor is less than that
for the tap on the lower floor. So the water pressure in the upper floor tap is lower than
that in the lower floor tap.
2.
When the acceleration due to gravity
(g) and the height of the liquid column
(h) are constant, the pressure at a point
in a liquid is directly proportional to its
density. i.e., P α ρ (keeping 'g' and 'h'
constant)
water
cooking oil
h
h
x
y
fig:variation of liquid pressure with its density
For example, one beaker is filled with water and the other is filled with oil of density 0.8
g/cm3 to the same level. If there are two identical holes at the same height on both the
beakers, the water comes out with more force due to high pressure. Hence the pressure
depends on the density of the liquid.
P HYS I CS
Optional Science - 10
27
3.
When the density of the liquid (ρ) and the height of the liquid column (h) are constant,
the pressure in a liquid is directly proportional to the acceleration due to gravity.
i.e. P α g (keeping 'h' and 'ρ' constant)
For example, the acceleration due to gravity varies on the basis of the distance from the
center of the earth. The acceleration due to gravity at the pole is 9.83 m/s2 and that at the
equator is 9.78 m/s2. When two identical water tanks- one at the equator and another at
the pole - are filled completely, then the pressure is more at the bottom of the tank at
the pole.
Solved Numerical- 2.1
The density of mercury is 13,546 kg/m3. Find the pressure exerted by the mercury column of
height 760 mm. What height of the water column will exert the same pressure?
Solution:
Here, density of water (ρ) = 13,546 kg/m3
Height of the mercury column (h) = 760 mm =
The liquid pressure is given by
760
= 0.76 m
1000
P = hρg
Or,
P = 0.76 × 13,546 × 9.8
∴
P = 100890.6 Pa
Pressure of the mercury column (P) = 100890.6 Pa
Height of the water column to exert the same pressure of 100890.6 Pa is given by
100890.6 = h × 1000 × 9.8
100890.6
= 10.3 m
9800
Therefore, the height of the water column to exert the pressure of 100890.6 Pa is 10.3 m.
h=
Properties of liquid pressure
Liquid pressure does not depend on the shape of the container. It acts in all directions
and remains the same for all directions. Liquid pressure applies force at 90o to any
contact surface.
Some consequences of liquid pressure
i.
Deep sea divers wear a stout steel suit
The liquid pressure is directly proportional to the depth from its free surface. The
deeper an object is in water, the greater the pressure acting on the object. This effect
is experienced by the deep seadivers. They feel the increasing water pressure on their
body while swimming deeper under water. This may cause some blood vessels to burst,
resulting in bleeding. Thus, they wear a special kind of suit to counter the high pressure
at great depths in the sea.
ii.
Walls of a dam are made thicker at the bottom
Water pressure increases with depth. When water is stored in a dam,
then there is high pressure at its bottom. It exerts more force on the
dam. Therefore, to withstand the high pressure exerted by the water
at greater depth, the walls of a dam is made thicker at the bottom.
0
28
Optional Science - 10
P HYS I CS
dam wall is
made thicker
at the bottom
iii.
Water supply tank is placed at a height
In a city area, water supply tanks are placed at a higher point as compared to the heights
of the buildings in the area. Water pipes are distributed in different regions of the area
to supply water. When tanks are placed at a greater height, the pressure of water will be
large enough to force the water to rise up the multi-storeyed buildings.
In case of the water tanks in tall buildings, water tanks are placed at the top. This
increases the height of the water column in the water pipes of the building. Due to
this, water pressure on the taps increases, and it helps to fill water faster and to take a
shower.
Types of molecular force
Every matter is made up of minute particles called molecules. These molecules exert a force on
one another. The force of attraction or repulsion between the molecules is called intermolecular
force. Such a force is in between like molecules as
Adhesion
well as unlike molecules. On the basis of the type of
Cohesion
interacting molecules, the intermolecular forces are
classified into: cohesive force and adhesive force.
-.-.-..:.:.-i..:....._....i.i._.w...._ Adhesion
fig:adhesion and cohesion
Cohesive force
The force which attracts liquid molecules to each other
is called cohesive force. It is also known as a force of
cohesion. Cohesive force makes liquid molecules cling
together. It is responsible for the formation of liquid
drops and surface tension.
c5-
ti"
"'+H/ ' H "'+
0
0
·o· .. 5 -
8+- /
,._,
',._,
8+-
··•.. c5- ......
intramolecular
~ ··..•Q..... .- ~
covalent ' --...._ / ,
hydro9en
The attractive force varies in magnitude, depending on polarbondin9
H
H
bondin9
the substances concerned. Solids have a strong force of
c5+
c5+
fig:Intermolecular forces in water
cohesion. That's why they have a definite shape and
size. In the case of liquids, cohesive force among the molecules is relatively weaker. This makes
possible for the free movement of molecules within the volume of liquids. During such free
movement, molecules do not go out of the liquid surface. That's why liquids have a definite
volume but no definite shape. The cohesive forces are least amongst the molecules of a gas.
Adhesive force
The force which arises between liquid molecules and the molecules of the container is called
adhesive force. It is also known as the force of adhesion. Adhesive forces make the liquid wet
the surface of its container. Adhesive force is responsible for capillary rise. For example, water
wets a glass surface. This is due to the adhesive force between the water molecules and the
glass molecules. The adhesive force is more than the cohesive force in this case. By waxing the
glass surface, we can reduce the adhesive force and allow the cohesive force between the water
molecules to pull the surface into spherical drops.
Adhesive force is different for different substances. For example, the adhesive force between
the gum and a solid surface is stronger than that between water molecules and a solid surface.
That’s why gum is used to paste paper, photographs, etc.
P HYS I CS
Optional Science - 10
29
The surface phenomenon of liquids: Surface tension
We observe that liquids form drops, water wets some surfaces but run off others, pond-skater
or water strider insects rest on the surface of water without sinking, water rise up a capillary
tube but mercury is pushed down to a lower level in a capillary tube. This is due to the tension
on the surface of a liquid. The surface of a liquid behaves as though it is covered by a stretched
membrane.
Molecular theory of surface tension: Cause of existence of tension on the surface of a liquid
B
The exposed surface of a liquid in a container acts like a stretched membrane
that exerts force on the liquid enclosed. This is due to the force of attraction
between the surface molecules and neighboring molecules of the fluid.
In the given figure, the wholly submerged molecules have attractive forces
in all direction. Such forces are canceled out. Therefore, the net force on
A
the wholly submerged molecules is zero. On the free surface, the number
of molecules in the lower half of the sphere is more and the upper half is
completely outside the surface of the liquid. Therefore, all the molecules lying on the surface
of a liquid experience only a net downward force. So horizontally, they attract each other
and act like a membrane. The free surface of a liquid tends to assume minimum surface area
by contracting and remains in a state of tension like a stretched elastic membrane. Thus, the
surface tension is mainly caused by the unbalanced cohesive force acting near the top surface
of the liquid.
Surface tension
The surface of a liquid behaves like a stretched rubber sheet. The
tension of the surface of a liquid can be measured by the concept
of tension of a stretched rubber sheet. The tension on a rubber
sheet is always measured in terms of the pull that is exerted on
a certain length of the boundary. The larger the length under
consideration, the greater is the pull.
T I
I T
Surface tension is the property of the free surface of a liquid at rest to behave like a stretched
membrane in order to acquire minimum surface area. It is due to the attractive force exerted
upon the surface molecules of a liquid by the molecules beneath that. Such a force tends to
draw the surface molecules into the bulk of the liquid. Imagine a line AB on the free surface
of a liquid at rest as shown in the given figure. Surface tension is measured as the force acting
per unit length on either side of this imaginary line AB. The force is perpendicular to the line
and tangential to the liquid surface. If F is the force acting on the length l of the line AB, then
surface tension is given by
F
l
Thus, surface tension is defined as the force per unit length acting perpendicular on an
imaginary line drawn on the liquid surface, tending to pull the surface apart along the line.
T=
Memory Plus
The SI unit of surface tension is newton per meter, denoted by N/m and the CGS unit is
dyne/cm.
0
30
Optional Science - 10
P HYS I CS
Experiments to demonstrate surface tension
Liquid surface behaves like a stretched elastic skin and tends to have a minimum surface area.
It can be demonstrated by the following simple experiments and observations:
1.
Floating a needle or a paper clip
Have you ever dropped a sewing needle or a paper clip horizontally in water? If you
have, did it sink? Obviously, an iron needle sinks when you drop it into water. Now try
it with full caution. Is it possible to make a needle or paper clip float?
Materials required: a glass tumbler, water and a sewing needle or paper clip
Procedure:
1.
Fill a trough half with water.
2.
Rest the steel needle on a small piece of blotting or filter paper and gently place it
on the surface of water.
After a while, the soaked paper sinks, leaving the needle floating
on the surface. Look carefully at the water surface around the
floating needle, do you observe the surface depressed? The
surface of water is depressed and stretched like an elastic skin.
The stretched elastic surface provides a stronger upward force
to support the needle. It is different from the upthrust from
the displaced water. What do you observe after adding some
drops of dish soap into water?
Explanation: The magnitude of pressure exerted by an object depends on its weight and
contact area. A steel needle has a small contact area when we drop it vertically, which
leads to a large pressure on the surface of water. It tears the stretched surface of the
water and the needle sinks to the bottom of the water. On the other hand, if it is kept
horizontally on the water surface with full caution, the contact area increases and
pressure exerted on the water surface becomes less. In this case, the stretched water
surface is not torn. As a result the needle floats in water.
When some drops of dish soap are added in
the water, the cohesive force between the water
molecules decreases, and the surface tension also
decreases. So the needle or paper clip will sink in
the water.
2.
Volume of water displaced
membrane
fig:floating needle on surface of water
Clinging of hairs of a painting brush
Materials required: Water, beaker and a painting brush
Procedure
1.
Dip a painting brush into water. Do you observe that its
hairs get separated from each other?
2.
Take the brush out from the water and observe the hairs
again. Do you observe them clinging together this time?
P HYS I CS
fig:Clinging of hairs of a
painting brush
Optional Science - 10
31
Explanation: When a painting brush is dipped in water, its hairs get separated from
each other. When the brush is taken out of water, it is observed that its hairs will cling
together. This is because the free surface of the water film tries to contract due to surface
tension.
3.
Water drops on a coin
Have your ever tried to fit water drops on a coin? How many drops can you fit on a
coin? Do it practically.
Materials required: Coin, water in a beaker and a medicine dropper
Procedure:
1.
Add one drop of water on a coin. Does it fit on your coin?
2.
Continue adding drop scarefully until the water spills off the coin.
3.
Repeat it 2 more times. Finally find the average number of drops that can fit on a
coin.
Explanation: Water molecules pull each other due to cohesion. At the same time, the
molecules on the surface form a stretched layer, which produces surface tension.
Consequences of surface tension
1.
The drips from a tap are round droplets: A drop or droplet is a small
column of liquid, bounded completely, or almost completely, by free
surfaces. Surface tension pulls the drips from a tap into round
droplets.
2.
Meniscus effects: Meniscus effects are due to surface tension. Any
water surface in contact with a vertical glass wall curves up to meet
the wall. Mercury in contact with a vertical glass wall curves down
to meet the glass. But the remaining surface remains stretched like a
membrane. This gives rise to a concave or convex meniscus.
Concave
meniscus
-
Convex
meniscus
Mercury
3.
Tendency of liquid to assume spherical shape: In the case of liquid outside a container,
it is spherical in shape like a rain drop. For example, small drops of mercury are
spherical. A drop of mercury is governed by two factors- surface tension and gravity.
Gravity pulls the molecules downward, and it tries to spread the liquid, while the
surface tension tries to collect it in the form of a sphere so that it has minimum surface
area. When we touch a mercury drop with a needle, a dimple is formed at the point of
contact, which disappears as soon as we remove the needle. Such a drop behaves like
an inflated rubber balloon.
4.
Formation of lead shots: A shot is a collective term for small balls, or pellets, often
made of lead. A lead shot is also used for a variety of other purposes, such as filling
cavities with dense material for balance. For example, a bulb of a hydrometer is filled
with lead shots to keep it upright in water. The lead shot was
originally made by pouring molten lead through screens into water
from a sufficient height. During its fall, the molten lead forms small
spherical drops due to surface tension forces, and on entering water,
they become solid.
32
Optional Science - 10
P HYS I CS
5.
Surface tension minimizes surface to form bubbles: Bubbles are held together by
surface tension. A small soap bubble in air forms a sphere. Surface tension in the film
acts to reduce the bubble size. So its internal pressure must be greater than the pressure
outside.
6.
Water striders or pond skaters are able to walk on water:
They rest on the surface of water without breaking it. A
dimple is formed where the surface is stretched by the
insect's feet. The surface tension causes the insect's feet to
make indentations on the water surface and has the same
characteristic as that of an elastic balloon surface.
7.
Separation of oil and water: Surface tension of oil is less than that of water. The
separation of oil and water is caused by the difference in surface tension of the two
liquids. When a drop of oil is dropped on the surface of water, due to higher surface
tension of water, the oil is stretched in all directions as a thin film. Thus oil makes a thin
film when it spreads in water.
8.
Mosquitoes breed on the free surface of stagnant water:
Due to surface tension, the surface of water acts like a
stretched layer. It can support the eggs laid by mosquitoes.
On spreading oil in water, it makes a thin layer on the surface
of water. Such a film of oil is of low surface tension. So
mosquitoes cannot breed on the oiled surface of water.
'
........
....._......
-"'--~
•,•-.,,
.,
/
,/
9.
Lubricating oils spread easily: Lubricating oils spread easily to all parts because of
their low surface tension.
10.
Antiseptics spread easily: Liquids with low surface tension spread easily. So the
surface tension of antiseptics like Dettol is kept low so that it can be easily spread on
the wounds.
Factors affecting surface tension
1.
Temperature: Surface tension decreases with rise in temperature. For example, the
surface tension of hot soup is less than that of cold one. It spreads over a larger area of
the tongue of a person. That makes hot soup more tasty than the cold one.
2.
Contamination: Contamination like oil on water, mixing of grease and dust, etc. reduce
the surface tension of water. This reduces the force between the water molecules. For
example, a floating paper clip on water sinks by adding some amount of detergent in it.
But the surface tension of water increases slightly on adding salts like common salt in it.
Viscosity
Activity
1.
Take a beaker filled with 2/3 rd of water and put a glass rod in it. Stir it to set the water in
rotation. Do you see that water rotating in the form of co-axial cylindrical layers?
2.
Stop stirring. Do you observe that the speed of the innermost cylindrical layer is
maximum?
The speed of successive layers of water decreases gradually as we observe from the center
of the beaker to its wall. After sometime, the water comes to rest. This is due to the internal
friction between the liquid layers.
P HYS I CS
Optional Science - 10
33
Have you ever noticed the flow of water and that of gum? Water flows more easily than gum.
Some liquids flow more easily than others. Such flow of liquid involves different parts flowing
with different velocities. These parts slide past each other, as if they were in layers. If there is
little friction, the layers slide past each other with ease. But it is difficult in the case of more
friction between the two layers. Fluids in which the flow is difficult are called more viscous
fluids. For example, gum, syrup, etc. On the other hand, fluids in which the flow takes place
with ease are said to be less viscous fluid. For example, water, petrol, etc. More viscous fluids
offer more resistance to an object moving through them. The property of fluids to offer
resistance to objects moving through them is called viscosity.
Memory Plus
The internal frictional force exerted between the liquid layers in motion is called viscous force.
Viscosity is the property of a liquid in motion. Inside a fluid, viscosity is the property of a fluid
by virtue of which it opposes the relative motion between its adjacent layers. It acts on the
fluid between the slower and faster moving adjacent layers.
Cause of viscosity
There is intermolecular force of attraction between the liquid molecules. The different layers
of a liquid move with different velocities. The layer of liquid in contact with the wall is at rest,
while others above it move with increasing velocity. Due to intermolecular force of attraction,
every fast moving layer tries to move the next layer with it faster. Whereas every slow moving
layer tends to retard the adjoining fast moving layer of the liquid. Thus the internal tangential
force between the two adjacent layers of a liquid, called viscous force, is the cause of viscosity.
Examples of viscosity
1.
A stirred liquid, when left, comes to rest due to viscosity.
2.
Viscosity of air is less than that of water. So we can run fast in air but not in water.
3.
Liquids differ in viscosity. Some liquids (e.g. water) flow more easily than others (e.g.
honey).
4.
Honey and oil flow more easily at higher temperatures as increase in temperature
decreases viscosity.
Applications of viscosity
1.
2.
Viscosity of blood can be used to detect blood corpuscle deficiency.
An oil with suitable value of viscosity is used as a lubricant in engines.
3.
The viscosity of oil helps in applying brakes.
Measurement of viscosity of a liquid
Viscosity is a measure of how viscous a fluid is. It measures the resistance of a fluid to a body,
which moves through it. It is easier to move an object through a thin fluid with a low viscosity
(e.g. water) than through a thick fluid of high viscosity (e.g. honey).
Viscosity is measured in terms of pressure and time. Under a given pressure, a more viscous
liquid will take more time to move a given distance than a less viscous one. It can also be
measured in terms of time taken for an object with a given size and density to fall through the
liquid of interest.
34
Optional Science - 10
P HYS I CS
Memory Plus
A viscometer is an instrument used to measure the viscosity of a fluid. It is also called
viscosimeter. The SI unit of measurement of viscosity is Ns m-2. It is also called pascal
second (Pa s) or decapoise. In the CGS system, its unit is dynes-s cm-2, also called a poise.
1 decapoise = 10 poise
Factors affecting viscosity
Viscosity is affected by the size and shape of the molecules, the interactions between them and
temperature.
1.
Shape and size of molecules: Fluids with larger, more complex molecules have
higher viscosities. For example, long, chain-like molecules in polymers and the
heavier hydrocarbon compounds have high viscosity.
2.
Interaction between molecules: A fluid with strong intermolecular force does not
flow easily. Such a fluid has high viscosity. It is the chemical bond that determines
the viscosity of a particular fluid. Polar compounds can form hydrogen bonds that
link separate molecules together. This increases the overall resistance to the flow and
movement. For example, long molecules with noticeable polarity, such as glycerin and
propylene glycol have high viscosity.
3.
Temperature: Temperature has a major effect on viscosity. Viscosity of a substance is
expressed at a fixed temperature. In liquids, it decreases with temperature. For example,
syrup or honey moves easily when they are heated.
Know the Reason
Viscosity of liquids decreases with increase in temperature, why?
On increasing the temperature of a liquid, the molecules move apart, and the intermolecular
force decreases. They spend less time in contact with one another. So viscosity of liquids
decreases with increase in temperature.
Viscosity of gases increases with increase in temperature, why?
At high temperature, the gas molecules move faster, and there are more collisions between
them. Resistance to movement in gases increases with increase in temperature, which
reduces their ability to flow. So viscosity of gases increases with increase in temperature.
Water has low viscosity, why?
Water is a polar molecule, but it has low viscosity because of the small molecules.
Elasticity
Different types of external forces act on a number of bodies in our surrounding. Such external
forces may produce change in the length, volume and shape of the body. The external force
which produces change in the length, volume, and shape of a body is called deforming force.
When a deforming force is applied on a body, which is not free to move, the shape or size of
the body changes. A body which experiences a deforming force is called deformed body.
P HYS I CS
Optional Science - 10
35
A relative displacement of particles takes place when an external force is applied on a body,
which is not free to move. If the particles are displaced with a certain limit, they regain their
original position after the deforming force is removed. When the deforming force is removed,
the body regains its original state due to the force developed within the body. Such a force
developed within a body, which restores the body to its original state, is called restoring force.
The property of a material to regain its original state when the deforming force is removed is
called elasticity. The body which possess the property of elasticity is called an elastic body.
Cause of elasticity
Matter is made up of atoms or molecules. The space between atoms or molecules varies in
different types of matter. Hence, the force of attraction between the molecules also varies. The
average location of the molecules in a solid material does not change with time. They are
packed together, their kinetic energy is also very small. This gives a definite shape and
appreciable stiffness or rigidity. Due to this rigidity, matter tends to regain the shape and size
when an external force tries to change its configuration.
Spring-ball system concept of elasticity: When the deforming
forces on the atoms in a solid are removed, the interatomic forces
bring them back to their original position. Such a mechanism can
be visualized by taking a model of the spring-ball system as shown
in the given figure. In the figure, the balls represent the atoms and
the springs represent interatomic forces. If we try to displace any
ball in the system from its equilibrium position, the spring system
tries to restore the ball back to its original position.
fig:spring ball concept of elasticity
Some examples of elasticity
1.
When we stretch a rubber band, its length increases. On removing the deforming force,
it comes back to its original length.
When a rubber ball is pressed, it gets deformed. But it regains its shape on removing
the deforming force.
An archer bends the bow to shoot an arrow. The bow springs return back to their
original form when the arrow is released.
When a steel wire is loaded at one end by keeping the other end fixed, then it gets
deformed. But it regains its original length on removing the changed load. Steel is
highly elastic. So springs are made of steel.
2.
3.
4.
In the above examples, the rubber band, rubber ball, bow and steel are elastic objects.
Perfectly elastic body
The extent to which the original form of a body is restored, when the deforming forces are
removed, is not the same for all materials. It varies from material to material. A body which
completely regains its original shape and size after the removal of the deforming force is said
to be perfectly elastic. There are no perfectly elastic bodies. It is an ideal concept only. Quartz
fiber and phosphor bronze (an alloy of copper with tin and phosphorus) are nearly perfectly
elastic bodies. Phosphor bronze is used for suspension purpose. In very sensitive instruments,
quartz fiber is used in place of phosphor bronze.
0
36
Optional Science - 10
P HYS I CS
Perfectly plastic body
Do you have any experience in clay art? We can give shape to clay while making a design. Wet
clay does not show any tendency to regain its original configuration after deformation. Bodies
which do not exhibit the property of elasticity are called plastic. For example, perfectly wet
clay is highly plastic. Bodies which do not exhibit the property to return to their own shape
and size after removing a deforming force are called perfectly plastic. Putty, semi-solid coal
tar, paraffin wax are examples of nearly plastic bodies. Such bodies retain their deformed
shape and size. The property of a body by virtue of which it tends to retain the altered shape
and size on removal of a deforming force is called plasticity.
Memory Plus
Bodies which partially regain their original form after removing a deforming force
are called partially elastic. Actual bodies have elasticity in between the limit of perfect
elasticity and perfect plasticity.
Material Parameters that Determine Elasticity
Most materials which possess elasticity in practice remain purely elastic only up to very small
deformations. In engineering, the amount of elasticity of a material is determined by two
types of material parameter.
1.
Modulus of elasticity: It measures the amount of force per unit area needed to achieve
a given amount of deformation. It is used to describe the elastic properties of objects
like wires, rods or columns when they are stretched or compressed. The SI unit of a
modulus is pascal (Pa). The higher the modulus of elasticity of the material, the greater
the rigidity. Such material is harder to deform. It means more force must be applied to
produce a given deformation. For example, the modulus of elasticity of steel is about
200 GPa(depending on the kind of steel). So it is suitable for the most bridges with the
longest spans.
2.
Elastic limit: If an elastic material is stretched or compressed beyond a certain limit, it
will not regain its original state and will remain deformed. The maximum stress that a
piece of material can withstand without being permanently deformed is called elastic
limit. SI unit of elastic limit is pascal (Pa).
Stress
Relative displacement of the particles in a body takes place when an external force acts on
it. The body is, thus, said to be deformed. In a deformed body, a restoring force is set up
within the body, which tends to bring the body back to the normal position. This is due to the
property of elasticity. The magnitude of these restoring forces depends upon the deformation
caused. The restoring force is equal in magnitude, but opposite in direction to the external
forces. This restoring force developed per unit area of a deformed body when subjected to an
external deforming force is known as stress.
In a position of equilibrium, the restoring force is equal to the external impressed deforming
force. Thus, stress is measured by the magnitude of the deforming force acting on a unit area
of the body. i.e.,
P HYS I CS
Optional Science - 10
0
37
Stress =
Restoring force F
=
Area
A
Where 'F' is the deforming force acting on an area 'A' of the body.
Memory Plus
In SI, the unit if stress is Nm-2 and in the CGS system its unit is dyne cm-2.
Hooke's law
The law of elasticity was discovered by the English scientist Robert Hooke in 1660. It states
that, within elestic limit, the displacement or size of the deformation is directly proportional
to the deforming force or load.
F= kx
Mathematically, Hooke’s law states that the applied force 'F'
equals a constant 'k' times the displacement or change in length
'x', i.e F = kx. 'k' is called the spring constant. Its value depends not
only on the kind of elastic material under consideration but also
on its dimensions and shape. Hooke’s law can also be expressed
as F = −kx. Where 'F' is the restoring force of spring. The negative
sign indicates that the force acts in opposite direction of the
displacement.
Force-extension graph to determine elastic limit
0
x
F
2x
2F
•
fig:demonstration of Hooke's law
2.
Beyond the elastic limit: Beyond the
elastic limit, a spring shows plastic
behavior. When the load or applied
force exceeds the elastic limit, then the
spring stays deformed. It does not go
to its original length on removing the
hanged loads. Beyond the elastic limit,
the line curves off.
38
Optional Science - 10
P HYS I CS
Weight (N)
A spring supported by a rigid support is loaded with varying loads. As the load increases, the
extension of the spring also increases. The relation between tensile stress and extension of a
wire can be shown in the form of a graph as shown in the given figure. Looking at the graph,
we can determine the elastic limit of the spring.
1.
Below the elastic limit: In this region,
the extension is proportional to the
force. If the load is removed, then
10
the spring will go back to its original
8
length. Within this region, the graph is
E
a straight line (OE) passing through the
origin.
O
0 .5
1.0
1.5
Extension(cm)
fig:force-extension graph
2.0
2.5
Answer writing skill
1.
I
On what factors does liquid pressure depend?
Liquid pressure is given by
P = depth(h) × density of liquids (ρ) × acceleration due to gravity (g)
So liquid pressure depends on,
2.
i.
depth of liquid,
ii.
density of liquids, and
iii.
acceleration due to gravity
What is an elastic material?
An elastic material is one which when bent or stretched slightly goes back to its original
shape. For example, a rubber band, spring, etc.
3.
Which force is responsible for the elastic behavior of substances?
Restoring force is responsible for the elastic behavior of substances. It is the force which
tends to restore the original configuration of the body.
4.
Define plasticity.
The property of the material body by virtue of which it does not regain its original
configuration when the external force acting on it is removed is called plasticity
5.
Write differences between cohesive force and adhesive force.
Cohesive Force
Adhesive Force
The force which attracts liquid molecules The force which arises between liquid
to each other is called cohesive force.
molecules and the molecules of the
container is called adhesive force.
Cohesive force makes liquid molecules Adhesive forces make a liquid wet the
cling together.
surface of its container.
It is responsible for the formation of liquid Adhesive force is responsible for capillary
drops and surface tension.
rise.
6.
At a particular depth of a river and sea, water pressure is more in the case of the sea.
When the acceleration due to gravity (g) and the height of the liquid column (h) are
constant, the pressure at a point in a liquid is directly proportional to its density, i.e.,
Pαρ. Sea water has deposits of salt, and its density is more than that of river water. So,
at a particular depth of a river and sea, water pressure is more in the case of the sea.
7.
A water tank is kept on the roof of a five-storeyed building and the taps on the walls
are fixed at the same height on each of the floors. The water pressure on the tap of the
ground floor is 80,000 Pa whereas the water pressure on the tap of the third floor is
11,400 Pa. Find the height of the third floor. [ Ans: 7 m]
P HYS I CS
Optional Science - 10
0
39
Solution:
Here, pressure on the tap of the third floor (P1) = 11,400 Pa
Pressure on the tap of the ground floor (P2) = 80,000 Pa
Let, the depth of water column up to the tap on the third floor = h1
The depth of the water column up to the tap on the ground floor = h2
Now the difference in pressure is
P2 – P1 = h2ρg – h1ρg = (h2 – h1)ρg
Or,
80000 – 11400 = (h2 – h1) × 1000 × 9.8
Or
h2 – h1 =
68600
= 7m
9800
Therefore, the height of the third floor is 7m.
8.
How does the knowledge of the factors affecting liquid pressure help us in our
practical life? Explain your view in two points.
In city areas, water supply tanks are placed at a higher point as compared to the heights
of the buildings in the area. When tanks are placed at a greater height, the pressure of
water will be large enough to force the water to rise up the multi-storeyed buildings.
Water pressure increases with depth. When water is stored in a dam, then there is high
pressure at the bottom. It exerts more force on the dam. Therefore, to withstand the high
pressure exerted by the water at greater depth, the wall of a dam is made thicker at the
bottom.
0
40
Optional Science - 10
P HYS I CS
Exercise
_
_ _JQ__
-----
Step
1
Define
1. Fluid
2. Pressure
3. Liquid pressure
4. Intermolecular force
5. Surface tension
6. Deforming force
7. Deformed body
8. Restoring force
9. Elasticity
10. Plasticity
11. Viscosity
12. Viscous force
13. Stress Very short answer questions
1.
Write the SI unit of the following:
a.
Pressure
b. Surface tension
2.
c. Viscosity
Write the formula to calculate
3.
a. surface tension
b. stress
On what factors does liquid pressure depend?
4.
Give two examples of surface tension.
5.
What is an elastic body?
6.
Give two examples of elasticity.
7.
What is meant by plastic body?
8.
Give two examples each of a more viscous fluid and less viscous fluid.
9.
Write two examples of elasticity.
10.
Out of two fluids; water and honey, which one has more viscosity?
11.
Name a device which is used to measure the viscosity of fluid?
12.
State Hooke’s law?
13.
Write two examples each of bodies which are almost perfectly elastic and perfectly
plastic.
P HYS I CS
Optional Science - 10
41
Step
2
Short answer questions
1.
How do each of following factors affect liquid pressure? Write with an example.
a. The density of a liquid
b. The height of a liquid column
c. The value of acceleration due to gravity
2.
Give two examples of each in which cohesive force is dominant and adhesive force is
dominant.
3.
Mention any four consequences of surface tension.
4.
How is surface tension applicable? Give two supporting examples.
5.
Write in short about the two factors which affect each of following
a. surface tension. b. viscosity
6.
c. elasticity
Write the conclusion that can be obtained from the force-extension graph.
Differentiate between
1.
Cohesive force and adhesive force
3.
Elasticity and plasticity
4.
Perfectly elastic and perfectly plastic
Give reason
1.
Shape of a water droplet is formed on a waxed surface.
2.
When a painting brush is dipped in water, its hair gets separated from each other, but
when it is taken out of water its hairs cling together.
3.
Mosquitoes can breed on the surface of water.
4.
Antiseptics have low surface tension.
5.
Viscosity of liquids decreases with increase in temperature.
6.
Viscosity of gases increases with increase in temperature.
Step
3
Numerical problems
1.
Find the pressure due to mercury column of height 76 cm in a mercury barometer.
(Density of mercury = 13.6 gm/cm3 and acceleration due to gravity = 9.8 m/s2)
[ Ans:101292.8 Pa]
2.
Calculate the pressure exerted by a mercury column of height 750 mm at its bottom.
Given that the density of mercury is 13.6 g/cm3 and g = 9.8 m/s2. [Ans: 9.99 x 104 Pa]
0
42
Optional Science - 10
P HYS I CS
3.
If the pressure exerted by the water at the bottom of Taudaha Lake is 9.8 × 104 pa, calculate
the depth of this lake. [Ans: 10 m]
4.
A water tank is kept on the roof of a five-storeyed building and the taps on the walls
are fixed at the same height on each of the floors. The water pressure on the tap of the
ground floor is 1,15,600 Pa whereas the water pressure on the tap of the fourth floor is
7,800 Pa. Find the height of the fourth floor.
[ Ans: 11 m]
Draw a diagram
1.
To show meniscus of water in a test tube.
2.
to show meniscus of mercury in a test tube.
Step
4
1.
Derive the formula to calculate liquid pressure. The symbols used in the formula have
their usual meaning.
2.
Explain an experiment to show the effect of depth in liquid pressure.
3.
What is Molecular Theory of Surface Tension? Explain it in detail.
4.
How can you demonstrate the effect of surface tension?
5.
What is the cause of viscosity? Explain in short.
6.
What is the cause of elasticity? Explain in short.
7.
Explain the relation between the force applied on a spring and extension
Multiple choice questions (MCQs)
1.
2.
The force of cohesion is
a. maximum in solids
b. maximum in liquids
c.
d. maximum in gases
The phenomenon due to which exposed surface of a liquid, contained in a vessel, behaves
like a stretched membrane is called
a. viscosity
b. surface tension
c.
3.
d. plasticity
cohesion
d. none of the above
The molecules of ink stick to the molecules of paper, due to the force of:
a. adhesion
b. gravitation
c.
5.
elasticity
Water wets the surface of glass, due to the force of :
a. adhesion
b. gravitation
c.
4.
same in different matters
cohesion
d. none of the above
In the given figure, there are four containers filled with different liquids. Look at the
surface shape, in the case of which liquid is the cohesive force maximum?
a. 1
b. 2
P HYS I CS
Optional Science - 10
0
43
c.
6.
3
d. 4
Insects are able to stand and walk on the water surface due to
a. adhesion
b. gravitation
7.
c. cohesion
d. surface tension
Cause of viscosity in fluids is
a. cohesive force
b. adhesive force
c.
d. diffusion
gravitational force
Project Work
Surface tension of water and alcohol
1.
Take 2 coins, 2 medicine dropper, water, alcohol and a piece of paper.
2.
Place the two coins on the piece of paper. Use the dropper to drop alcohol and water on
the two coins individually.
3.
Count the number of water drops and alcohol drops until they just begin to overflow.
Which liquid can adjust more drops on the coin’s surface? Write your conclusion and
explain about the surface tension of water and alcohol in your classroom.
Floating razor blade on water
1.
Take water, beaker and a razor blade
2.
Fill a beaker half with water.
3.
Put a razor blade slowly in the position shown in the given figure. Does the razor blade
float on water?
44
Optional Science - 10
P HYS I CS
UNIT
3
ENERGY
Mark Zachary Jacobson, born in 1965, is a professor of civil and environmental engineering
at Stanford University and director of its Atmosphere/Energy Program. He develops
computer models to study the effects of different energy technologies and their emissions
on air pollution, weather, and climate. In a paper published in the journal, Nature, in 2001,
Jacobson theorized that black carbon, which is emitted during fossil fuel, biofuel and
biomass burning, may be the second leading cause of global warming after carbon dioxide.
Jacobson has also developed roadmaps to transition the world as a whole, all 50 U.S. states,
and 139 countries to 100% clean, renewable wind, water and solar (WWS) energy for all
energy purposes. His proposed transition will also eliminate millions of premature deaths
worldwide each year caused by air pollution and reduce disruption associated with fossil
fuel shortages.
Key terms and terminologies of the unit
1.
Energy: Energy is the ability to do work.
2.
Non-renewable sources of energy: The energy sources which occur in limited
and exhaustible amounts are called non-renewable energy sources.
3.
Fossil fuels: Sources of energy like coal, petroleum and natural gas, which are
formed from the remains of living beings buried inside the earth’s crust for
millions of years, are called fossil fuels.
4.
Fossil fuel energy: Energy from burning coal, petroleum or natural gas is called
fossil fuel energy.
5.
Nuclear energy: The energy stored in the nucleus of an atom is called nuclear
energy.
6.
Renewable sources of energy: Sources of energy, which are being produced
continuously in nature and are inexhaustible are called renewable energy
sources.
7.
Alternative energy sources: Sources of energy which are available in nature
and can be used instead of non-renewable energy sources are called alternative
energy sources.
P HYS I CS
Optional Science - 10
45
8.
Hydroelectricity: The electrical energy generated by rotating turbines connected
to the generators with the help of moving water is called hydroelectricity.
9.
Biofuel: Fuels like wood, biogas, alcohol, etc. from biomass of plants and animals
are called biofuels.
10.
Biomass: Biomass is any organic matter that can be obtained from living organisms.
11.
Biomass energy: Energy released from biomass by combustion or other chemical
processes is called biomass energy.
12.
Biogas: Biogas is a mixture of gases like methane (CH4), carbon dioxide (CO2),
hydrogen (H2) and hydrogen sulphide (H2S).
13.
Biogas plant: A biogas plant is a combination of a digester and gas holder, where
biogas is produced from animal dung, human excreta, industrial and domestic
wastes.
14.
Briquette: A briquette is a compressed block of coal dust, or other combustible
biomass materials, such as charcoal, sawdust, wood chips, peat, or paper, used
for fuel.
15.
Charcoal briquette: A charcoal briquette is a compressed block of charcoal.
16.
Biomass briquette: A block of flammable matter prepared by densification of
woody biomass, leafy biomass and agricultural residues is known as biomass
briquette.
17.
Briquetting plant: A briquetting plant is the technology to convert all types of
agro forestry waste into solid fuel.
18.
Solar energy: Solar energy is the light and heat received by the earth from the sun.
19.
Solar devices: Those devices which convert solar energy into other forms of
energy are called solar devices.
20.
Wind energy: Energy received from the movement of the wind across the earth is
called wind energy.
Introduction
Energy is important in everyone's life to carry out different works. Living beings need energy
for their survival and growth. Non-living things like motorcycles, tractors, buses, trucks,
aeroplanes, etc. require fuel for their running. Energy is the ability to do work.
Living beings obtain energy from their food. Non-living things, like a vehicle, run on fuel.
There are different forms of energy, like fossil fuel energy, solar energy, nuclear energy,
wind energy, electrical energy, which are important to us. Such forms of energy are obtained
from a number of sources. In this unit, we will learn about types of energy sources, different
alternative sources of energy, their uses, advantages and disadvantages.
0
46
Optional Science - 10
P HYS I CS
Classification of energy sources
Some of the energy sources cannot be generated in a short period of time. Whereas the others
can be replenished in a short period of time. So there are mainly two types of energy sources.
They are non-renewable energy sources and renewable energy sources.
Non-renewable energy sources
The energy sources which occur in limited and exhaustible amounts are called non-renewable
energy sources. Such energy sources cannot be generated in a short period of time. They cannot
be used again and again. Fossil fuel, nuclear fuel, etc. are the examples of non-renewable
sources of energy.
Sources of energy like coal, petroleum and natural gas, which are formed from the remains of
living beings buried inside the earth’s crust for millions of years, are called fossil fuels. They
are formed by natural processes such as anaerobic decomposition of buried dead organisms.
Fossil fuels contain high percentages of carbon. Other commonly used derivatives of fossil
fuel include kerosene and propane.
Renewable sources of energy
The sources of energy, which are being produced continuously in nature and are inexhaustible,
are called renewable energy sources. For example, wood, charcoal, many agricultural wastes.
Such energy sources can be replenished in a short period of time.
Alternative energy sources
The present rate of fossil fuel consumption is high. This will invite an energy crisis in the near
future. To avoid this, we need to find sources of energy which can replace fossil fuel. The
sources of energy which are available in nature and can be used instead of non-renewable
energy sources are called alternative energy sources. Renewable sources of energy are
also called alternative sources of energy. The government of Nepal has made its policy to
promote alternative sources of energy for conservation of energy sources. Alternative Energy
Promotion Centre (AEPC) is a Government institution established on November 3, 1996 under
the Ministry of Science and Technology with the objective of developing and promoting
renewable/alternative energy technologies in Nepal.
Hydroelectricity
Water collected in a dam at a certain height possesses potential energy. When it is allowed
to fall through a tunnel, then it has kinetic energy. This energy can be used to rotate turbines
connected to a generator. The electrical energy generated by rotating turbines connected to
the generators with the help of moving water is called hydroelectricity. A hydroelectricity
generating station, which utilizes the potential energy of water at a high level, is known as a
hydroelectric power plant.
Principle of generation of hydroelectricity
To generate hydroelectricity from a hydropower plant, water collected in a dam is allowed to
pass through a tunnel. It converts the potential energy of water stored in a dam into kinetic
energy. The force of water can be used to turn turbines connected to the generator to produce
P HYS I CS
Optional Science - 10
47
electricity. So kinetic energy of the flowing water is converted into kinetic energy in the
armature of a generator connected to the turbine and finally to the electrical energy. Thus
kinetic energy is converted into electrical energy.
Technology of generation of hydroelectricity
A large volume of water from a source
like river is stored in a dam. Such water
is allowed to fall through a long tunnel
over turbines connected with a generator.
It rotates the armature of the generator
at a high speed. In order to produce an
alternating current of 50 Hz, it is made
to rotate at a speed of 50 revolutions per
fig:Technology of generation of hydroelectricity
second. The rotation of the armature of the
generator between two poles of a strong magnet gives rise to electric current, or electricity.
This electricity is transmitted to the sub-stations through a transformer for further distribution
to the houses and factories.
Hydroelectricity as the largest source of renewable energy
Hydroelectricity is the world's most used renewable power source. In 2015, hydropower
generated 16.6% of the world's total electricity and 70% of all renewable electricity and was
expected to increase by about 3.1% each year for the next 25 years. In Nepal, it is estimated that
the total production capacity of hydroelectric power is about 83,000 megawatts (MW). But the
existing hydroelectric power production in Nepal is only 1,232 MW. Pharping Hydro Power,
the first hydropower project, was established in 1911 as Chandrajyoti Hydro-electric power
station by Prime Minister Chandra Shamsher Jang Bahadur Rana.
Know the Reason
Hydroelectricity is the most suitable source of energy in context of our country, why?
In Nepal, there are many fast flowing perennial rivers. These rivers flow from the north
to the south on sloppy land. Such a sloppy land structure is suitable for storing water
in dams. So hydroelectricity is the most suitable source of energy in the context of our
country.
Advantages of hydroelectricity
1.
Hydroelectricity does not cause air pollution.
2.
It can be transmitted over long distances in extremely small time.
3.
It can be converted into different forms of energy, like heat, light, etc. by passing through
suitable devices.
4.
Water used to generate hydroelectricity can be reused for other purposes like irrigation.
5.
It is cheaper in the long term use though the installation cost of a hydropower plant is
very high.
48
Optional Science - 10
P HYS I CS
Limitations of hydroelectricity
1.
It results in submersion of extensive areas upstream of the dams.
2.
Damming rivers may disrupt wildlife and natural resources.
3.
Hydropower stations cannot be sited at a place of our choice.
4.
Dams can be very expensive to build.
5.
There must be continuous and sufficient flow of water for steady output.
Biofuel: Biogas
Fuels likes wood, biogas, alcohol from the biomass of plants and animals are called biofuels.
Plants trap the sunlight during photosynthesis. Solar energy gets stored in the form of organic
matter in plants. Biomass is any organic matter that can be obtained from living organisms.
For example, wood, crops, dried leaves, seaweed, animal wastes. We use biomass when we eat
plant products or when we burn firewood.
Know the Reason
Biomass is a renewable energy source, why?
Plants and animals will always exist as long as the conditions are suitable for life on the
earth. As long as we plant trees and crops, we will have resources. Biomass supplies
are not limited. It can be obtained continuously on the earth. So biomass is a renewable
energy source.
Biogas: Biomass can be converted into combustible gas, i.e., biogas in a biogas plant. Biogas
is a mixture of gases like methane (CH4), carbon dioxide (CO2), hydrogen (H2) and hydrogen
sulphide (H2S). The major constituent of biogas is methane (65 %).
Memory Plus
Energy released from biomass through combustion or other chemical process is called
biomass energy.
Construction of biogas plant
A biogas plant is a combination of a digester and gas holder, where biogas is produced from
animal dung, human excreta, industrial
Slurry ol Cattle
, ;=;.,+-- Outftowf0< 8101111
Dung & Water
and domestic wastes. In other words, the
Mbclng Tank
biogas plant is the physical installation
to produce biogas from biomass. It is Ground Level
built either of cement-concrete or bricks.
Biogas plant was first introduced to
Overflow Tank
Nepal as an experimental project in
1955. The initial experiences showed the
Outiet Chamber
feasibility of this technology for meeting
a significant portion of rural household
energy needs. A biogas plant has the
following components:
fig: construction of biogas plant
--
P HYS I CS
-
Optional Science - 10
49
a.
Mixing tank: Feed is fed into the system from a mixing tank. It has a mixing fan to make
slurry from animal dung and water.
b.
Inlet Pipe: It is the pipe from the mixing tank to the digestive tank. It is used to send the
feed into the digestive tank.
c.
Digestive tank (T): It is a brick-walled underground tank with a dome shaped roof.
A digester is an air-tight tank where the feed and water will stay for some time and
bacterial operation to generate gas will get complete.
d.
Dome (gas holder): It stores the biogas generated. With increase in the pressure of the
gas inside the dome, it pushes the digested material out of the tank.
e.
Gas outlet: It is a pipe with a valve at the top of the dome. Gas generated is supplied
through an outlet valve. Biogas from the biogas plant can be supplied through pipes for
cooking and lighting.
f.
Outlet chamber: It is a rectangular tank on the opposite of the input pipe. The outlet
chamber is for taking out the spent slurry after completion of gas generation from it.
g.
Overflow tank: There is an overflow tank over the outlet chamber.
h.
Slurry outlet: It is on the overflow tank. Slurry is discharged from the outlet opening.
Input materials for biogas production
The following organically-rich matter is used as input material for biogas production.
a.
Animal wastes: Cattle dung, urine, goat and poultry droppings, sericulture wastes,
elephant dung, piggy wastes.
b.
Human wastes and kitchen wastes: Human excreta and other kitchen wastes like
chopped vegetables or fruit waste, food gone bad, leftover food. But bony items and other
hard substance should not be added in the mixing tank.
c.
Agricultural wastes: Aquatic and terrestrial weeds, crop residues fruit and vegetable
processing wastes, oil cake, etc.
d.
Industrial wastes: Sugar factory and paper wastes are industrial wastes that can be
used as input material for biogas production.
In the villages, the main input material for biogas production is cattle dung.
Production of biogas
When cattle dung is used as input material in the mixing tank for biogas production, a slurry
is made from fresh dung and water in the ratio 1:1. This slurry of animal dung and water is
fed into the digester tank. The digester tank is filled with slurry upto the cylindrical level as
shown in the given figure of the biogas plant. Biogas is produced by the breakdown of organic
matter by bacteria in the absence of oxygen. Such bacteria are called anaerobic bacteria.
After installation of the biogas plant, the gas production may take from a few days in summer
to 3- 4 weeks in winter. This biogas starts collecting in the dome. Initially an outlet valve is
kept closed to prevent the produced gas from escaping. After a few days, formation of bubbles
will be noticed in the outlet tank. As more and more biogas collects in the dome, it exerts
pressure on the slurry in the digester tank. The gas is allowed to accumulate till it almost
pushes the slurry to the level of the outlet opening and forces the spent slurry to go into the
overflow tank through the outlet chamber.
0
50
Optional Science - 10
P HYS I CS
From the overflow tank, the spent slurry is removed gradually. The spent dung slurry, left
after the extraction of biogas, is rich in nitrogen and phosphorus compounds and hence
forms good manure. The initial gas in the gas dome is allowed to escape. The gas is again
accumulated for three days, now the biogas will burn with a blue flame and is ready for use.
This gas will not have any odor while burning. It takes about 50 to 60 day for the new gasplant to start functioning.
Know the Reason
The initial mixture of gases collected in the dome of a biogas plant is allowed to escape
by opening the outlet, why?
The initial gas has more carbon dioxide (CO2) and less of methane (CH4). It has oxygen as
well as some other gases. So the initial mixture of gases collected in the dome of a biogas
plant is allowed to escape by opening the outlet.
Factors affecting the amount of gas generated
a.
Quality and quantity of feed: The amount of gas generated changes with the quality
and quantity of the feed. For example, to generate 1 m3 of biogas, 25 kg of cow dung or
3 kg of oil cake are needed.
b.
Temperature: The suitable temperature for biogas production is 35oC to 38oC. It
decreases below 20oC and stops below 8oC. In winter, the production of biogas from
a biogas plant decreases. Sometimes people add warm water while making slurry to
increase the production of biogas.
c.
pH value: The suitable pH range for bacterial growth is 6.8-7.8.
d.
Stirring digester contents: Stirring the input material and water to make slurry affect
its decomposition inside the digestive tank. If the slurry is made perfect, the production
of gas is increased.
Applications of biogas
a.
Cooking fuel: A biogas pipe is connected to a biogas stove to use it as a cooking fuel.
b.
Lighting fuel: Biogas can be burnt in lighting mantles for lighting purpose.
c.
To generate electricity: Biogas can be converted directly into electricity by using fuel
cells.
d.
Fuel for combustion engine: Biogas is used as fuel in combustion engines, which
convert it to mechanical energy.
Know the Reason
Biogas is one of the suitable sources of energy for villages in Nepal, why?
In the villages, many people are engaged in farming.
i. Raw materials like animal dung, plant waste are easily available.
ii. Bulbs can glow from the electricity generated from biogas for lighting purpose.
So biogas is a suitable source of energy for villages in Nepal.
P HYS I CS
Optional Science - 10
51
Advantages of biogas
a.
It produces more heat when burnt.
b.
It is a non-polluting fuel as it does not produce smoke. So it helps in controlling air
pollution.
c.
The spent dung slurry, left after the extraction of biogas, is rich in nitrogen and
phosphorus compounds. It provides nutrient-rich manure for plants.
d.
Biogas can also be used to produce electricity for lighting purpose.
Know the Reason
The spent dung slurry, left after the extraction of biogas, is used as good manure, why?
The spent dung slurry, left after the extraction of biogas, is rich in nitrogen and
phosphorus compounds and hence forms good manure.
Limitations of biogas plants
a.
Initial cost of installation of the plant is high.
b.
Limited biogas is produced in winter.
c.
In case a farmer owns only a few cattle, animal dung is insufficient to feed a biogas
plant.
d.
Construction of a biogas plant occupies some space. So it is not possible to construct
anywhere in the cities.
Briquette
The term briquette comes from the French language and is related to bricks. Briquettes are
solid fuel often used for domestic purposes in developing countries. They are used for heating
purpose in industries, too. Briquettes are formed by compacting solid material. Compaction
increases the heating value per unit volume. A briquette is a compressed block of coal dust
or other combustible biomass material, such as charcoal, sawdust, wood chips, peat or paper
used for fuel. Using waste to form briquettes allows the utilization of low-grade combustible
materials. Himalayan Green Energy Pvt. Ltd., Shubha Biomass Briquette Pvt. Ltd., R.S.
Briquette Factory Pvt. Ltd., etc. are producing briquettes to replace firewood and fossil fuels
in Nepal.
Know the Reason
Briquettes are densified, why?
Compaction, or densification, of briquettes is to increase the heating value per unit
volume so that it is comparable to coal.
Types of briquettes
There are different types of briquettes. They are coal briquette, charcoal briquette, biomass
briquette, paper briquette, etc. Although you will be learning about biomass briquettes in this
unit, there is information about charcoal briquettes, too because in Nepal these days charcoal
briquettes are produced on a commercial scale.
0
52
Optional Science - 10
P HYS I CS
Charcoal briquettes
A charcoal briquette is a compressed block of charcoal. It is produced by
burning a carbon-rich material such as wood in a low-oxygen atmosphere
and then mixing it with other binders. Charcoal briquettes are not actual
charcoal lumps, but a combination of charcoal and other ingredients
molded into easy-to-light lumps.
Biomass briquettes
..if
· . ,,,. . r
_,
_
__,
:,
fig:Charcoal briquettes
Biomass densification is known as briquetting of biomass. Briquetting of
saw dust and other agro residues has been practiced for many years in
several countries. A block of flammable matter prepared by densification
of woody biomass, leafy biomass and agricultural residues is known
as biomass briquette. They are renewable source of energy. Their use
fig:biomass briquettes
replaces the use of fossil fuels, such as oil or coal. It also substitutes the use of charcoal.
Raw materials
In developing countries, biomass briquettes are made from agricultural waste. Agricultural
wastes, like groundnut shells, castor seed shells, almond shells, coconut shells, rice husks,
cotton stalks, sunflower stalks, pine needles, coffee husks, jute waste, and forestry waste like
fallen leaves, tree bark, sawdust can be used to make biomass briquettes.
Types of biomass briquettes
Wood briquette
Wood briquettes are made from dry untreated wood chips. They are pressed at high pressure
without any binder. When wood is compressed at high pressure, then it changes into fuel like
brown coal. Wood briquettes have a lower ash and sulphur content than in fossil fuels.
Know the Reason
Burning a wood briquette is far more efficient than burning firewood, why?
The amount of water in a log determines how well it will burn and how much heat it
will produce. The moisture content of a briquette can be as low as 4%, whereas for green
firewood, it may be as high as 65%. Also the compactness of briquettes increases the
heating value per unit volume. So burning a wood briquette is far more efficient than
burning firewood.
Sawdust briquette
Sawdust is a byproduct of woodworking places like saw mills, furniture workshop, etc. It is a
cluster of fine particles of wood. Sawdust briquetting is a useful way of managing wood waste.
In order to make sawdust briquettes, the saw dust is fed into a briquetting machine. In such
machines, the sawdust is compressed by using hydraulic cylinders to make a reconstituted log
that can replace firewood. It is a process similar to forming a wood pallet but on a large scale.
No binders are involved in the manufacture of sawdust briquettes, too. The natural lignin in
the wood particles binds the dust together to form a solid.
P HYS I CS
Optional Science - 10
53
Rice husk briquettes
Rice husk contains cellulose, lignin, etc. The combustibility of rice husk is high, but the density
of rice husk is low. The combustion rate increases when it is converted into briquettes by
briquette machines. To make briquettes, rice husk is crushed into small pieces. Such crushed
rice husk is fed into a rice husk briquette machine to make briquettes.
Straw or hay briquettes
Whether the straw waste is from hay, corn, wheat or other agricultural crops, it can be used
to make briquettes. Instead of storing straw waste in bins, briquetting offers an option for
eliminating the need for storage, disposal and landfill fees. To briquette straw waste, the
moisture content is eliminated by drying it and crushed into pieces of a size two inches or less.
It is then fed into a straw briquetting machine for compaction. Briquettes produced from straw
waste are easy to store and transport.
Paper briquettes
Paper briquettes are made by compressing shredded paper materials into a small cylindrical
form. Paper briquetting minimizes the volume of paper waste and provides us a fuel for
heating purpose.
Manufacture of biomass briquettes: Briquetting technology
A briquetting plant is the technology to convert all types of agro forestry waste into solid
fuel. A briquette is manufactured by a briquetting machine, also known as a briquette maker
or briquette press. Briquetting plants with both small and high production capacities can be
found in Thailand. They have been successful in briquetting rice husk commercially. The
briquetting sector is growing moderately in India despite some failures. In other countries,
briquetting is not popular due to lack of advanced technology.
In Nepal, biomass briquetting was introduced in the year 1986 through a demonstration
program organised by a Japanese private company with the support of the Japanese Embassy.
The technology used for the demonstration, was based on the extruder principle and
manufactured by Fuji Conveyor. This program fostered a growth in the briquette manufacturing
industry. In 1987/88, four extrusion type briquetting machines were imported from Sun Chain
Company, Taiwan and established in Simara, Hetauda, Chitwan and Parwanipur. Nowadays
small briquetting machines are in operation. These can pave the way for large commercial
production of briquettes, which could make use of the huge quantity of agro-residue available
in our country..
Briquetting processes
The following processes are involved in a briquetting unit/ plant:
Raw
material
Crusher
Drier
Finished
Product
biomass
briquette -m achine
•
Production Processes Flow Chart
0
54
Optional Science - 10
P HYS I CS
Cooling
1.
Wood/straw crusher: The crushing machine prepares suitable size raw materials for a
briquetting plant. The choice of crushing machines depends on the type and size of raw
materials. A hammer mill is used to crush small-size materials.
2.
Briquetting dryer: It is done in the hot sun or by passing hot air to reduce the moisture
content from 25% to 10 %. In the case of large-scale production in a briquetting plant, the
choice of the dryer model depends on the original moisture content of raw materials.
3.
Briquetting press: To manufacture biomass briquettes, the raw materials are directly
supplied into the biomass briquette machine. It makes the biomass material into
briquettes. All materials containing lignite and cellulose are suitable for densification in
a briquetting machine.
There are mainly two types of briquetting machines; piston press briquetting machine and
screw extrusion briquetting machine. The briquettes produced by screw briquette extruder
have a concentric hole and have a larger specific area. Because of this, screw press briquettes
have better a high combustion rate. They do not disintegrate easily and are also homogeneous.
While briquettes of piston press are completely solid.
Screw extrusion briquetting machine: The screw extrusion type briquetting plant basically
consists of the following components:
1.
The electric motor, which drives the pulley for rotating the screw
2.
The hopper, for feeding the raw material
3.
The die heater and muff
4.
The screw, which densifies the raw material to produce briquettes.
The electric motor drives the briquetting screw, which is housed inside the die, through a Vbelt and pulley arrangement. Biomass raw material is fed to the screw through the hopper.
The electric die-heater softens the lignin in the raw material as it passes through the die, which
acts as a binding material. A smoke trapping system traps and removes the smoke from the
vicinity during the briquetting process. The produced briquettes are collected at the opening
provided at the bottom of the smoke collection box.
Uses of biomass briquette
Biomass briquettes can replace fuels like diesel, kerosene, lignite, coal, firewood. In our
country, where huge amounts of agro-residue are available, this technology can handle a wide
range of biomass to give good quality briquettes.
1.
It is used for room heating purpose.
2.
It is used as a fuel for cooking purpose in the kitchen, picnic spot, etc.
3.
People use briquettes for keeping the baby and new mother warm.
4.
It can be used instead of wood and loose biomass in small scale industries, like rubber,
leather processing, brick kilns, etc.
Memory Plus
Using biomass briquettes: First, ignite one end of it with gas until it turns
red. Transfer that briquette into the stove made up of ceramic, iron or steel.
The burnt part of the briquette is kept downward.
P HYS I CS
Optional Science - 10
55
Advantages of biomass briquette
1.
It is a renewable source of energy
2.
It is cheap and readily available.
3.
It is much cleaner to handle than charcoal or coal.
4.
It reduces air pollution and helps to conserve the environment.
5.
It replaces the use of fossil fuels like kerosene and LPG and traditional sources of energy
like, firewood, coal and dung cakes.
6.
Ash after complete combustion of a briquette can be used in the garden and field.
7.
Biomass briquettes are uniform in size and composition. So they are easier to store and
use for cooking than wood.
8.
Loose biomass causes problem in handling, transportation and storage. Briquettes are
easy to handle and eliminate problems of transportation and storage of loose biomass.
Disadvantages of biomass briquettes
Biomass briquettes have some drawbacks:
1.
It requires a huge investment for its initial production.
2.
In production, there is a high energy requirement.
3.
In the rainy season, the drying process needs another heat source other than the sun.
4.
Biomass briquettes must be stored in a waterproof place otherwise the briquettes will
not burn when lit.
5.
The quality of the raw materials and wear of the die, piston and screw are frequent
operational problems associated with briquetting technology.
Solar energy
You have already learnt about the sun as the ultimate source of energy and thermonuclear
fusion in optional science of class 9. You had learnt about applications, advantages and
disadvantages of solar energy too. Solar energy is the light and heat received by the earth
from the sun. It is the main source of energy on the earth. Life on Earth is possible due to solar
energy. The earth receives an enormous amount of energy directly from the sun each day. Sun
is an enormous source of energy. This energy is due to the nuclear fusion reaction taking place
in the core of the sun. It is understood that the energy given by the sun to the earth in one day
is 50,000 times more than the total energy consumed by the world in one year.
Solar energy can be harnessed using a range of technologies, such as solar heating,
photovoltaics, solar thermal energy. Solar cooker, solar furnace, solar water heater, solar
electric power plant are examples of devices that convert solar energy into other forms of
energy. Those devices which convert solar energy into other forms of energy are called solar
devices. In the last dacade, solar energy has also been used to power earth-orbiting satellities,
cars and even planes.
0
56
Optional Science - 10
P HYS I CS
Know the Reason
Solar energy is a useful source of energy in the context of our country, why?
On average Nepal has 6.8 sunshine hours per day. In most parts of our country, there
are about 300 sunny days in a year. It is estimated that if proper technology is employed,
then we can harness 20 MW of solar energy per square kilometer. So solar energy is a
useful source of energy in the context of our country.
Wind energy
Energy received from the movement of the wind across the earth is called wind energy. This
energy is a result of unequal heating of the earth’s surface and the atmosphere. The wind can
be obtained continuously. We never run out of it. So the wind is a renewable source of energy.
It is one of the oldest and cleanest forms of energy. The kinetic energy of the wind has been
traditionally used to pump water and to run flour mills and to propel sailing boats. A large
amount of energy can be produced from a windmill. Nowadays, the improved versions of the
windmill are used to generate electricity. It depends upon the weather and location to capture
wind energy.
Memory Plus
Nepal has capacity to generate more than 10,000 MW of electricity from wind energy.
Places above the Churiya range in Nepal get 15-17 hours of wind every day. Places like
Mustang, Dhading, Galchhi, Borlini are suitable for electricity generation from the wind.
Answer writing skill
1.
I
Name the alternative sources of energy which are suitable in our context.
Alternative sources of energy like solar energy, wind energy, biogas, biomass briquettes
and hydroelectricity are suitable in our context.
2.
What raw materials are used to make biomass briquettes?
Any type of agro-forestry waste or bio-mass like sawdust, groundnut shell, caster seed
shell, sugar-cane bagasse, cotton stalk, bamboo dust, rice husk can be used as raw
materials to make biomass briquettes.
3.
Write two advantages of biomass briquette over loose biomass
1.
The direct burning of loose biomass in the conventional way and gives less heat
and creates more air pollution.
2.
Loose biomass causes problems in handling, transportation and storage.
P HYS I CS
Optional Science - 10
57
4.
Fossil fuels are called non-renewable energy sources.
Coal, crude oil and natural gas are formed from the fossilized remains of prehistoric
plants and animals. They cannot be regenerated in a short period of time. It takes
millions of years for fossil fuel to form. Their supply is limited, and they cannot be used
again and again.
5.
Suggest two alternative sources of energy for rural areas in our country.
The following two sources of energy are suitable alternative sources of energy for rural
areas of our country.
1.
Solar energy: In places where there are no hydropower transmission lines, solar
panels can provide electricity.
2.
Biogas: It is a suitable fuel for the people in the villages of our country. The raw
materials to produce biogas are easily available in the villages.
6.
Write two uses of biomass briquettes.
The two uses of biomass briquettes are:
7.
1.
It is used as a fuel for cooking purpose in the kitchen, picnic spot, etc.
2.
People use briquettes for keeping the baby and the new mother warm after
delivery.
Relate the traditional and advanced ways of capturing wind energy
The kinetic energy of the wind has been traditionally used to pump water and to run
flour mills and to propel sailing boats. Large amounts of energy can be produced from a
windmill. Nowadays, improved versions of the windmill are used to generate electricity.
0
58
Optional Science - 10
P HYS I CS
Exercise
Step
1
Define
1. energy
2. wind energy 3. biomass
4. biofuel
5. alternative sources of energy Very short answer questions
1.
Name alternative sources of energy which are suitable in the context of our country.
2.
What is hydroelectricity?
3.
What is biogas?
4.
What is a briquette?
5.
What raw materials are used to make biomass briquettes?
6.
Write two advantages of biomass briquette over loose biomass.
7.
Name some of the suitable places for generating electricity from the wind in our country.
Step
2
Short answer questions
1.
'Hydroelectricity is the most suitable source of energy in our country.' Justify this
statement in two points.
2.
What are the input materials for biogas production?
3.
Write in short about the factors affecting the amount of biogas produced in a biogas
plant.
4.
Write in short about the different types of biomass briquettes.
5.
Write about the biomass briquetting processes.
6.
How does the method of compaction in briquetting increase the heating value?
7.
'Solar energy is a suitable source of energy in our country.' Justify this statement in two points.
P HYS I CS
Optional Science - 10
59
Differentiate between
1.
Renewable sources of energy and non-renewable sources of energy
2.
Charcoal briquette and wood briquette
Give reason
1.
A tremendous amount of energy is released during a nuclear reaction.
3.
Hydroelectricity is a multipurpose source of energy.
4.
Biomass is a renewable energy source.
5.
Biogas is one of the suitable sources of energy for the villages in Nepal.
6.
The initial mixture of gases collected in the dome of a biogas plant is allowed to escape
by opening the outlet.
7.
The spent dung slurry, left after the extraction of biogas, is used as manure.
8.
Burning wood briquette is far more efficient than burning firewood.
Step
3
1.
Write three uses of hydroelectricity and biogas.
2.
Write three advantages and three disadvantages of the following:
1. Hydroelectricity
2. biogas
3. biomass briquettes
Draw a diagram to show the construction of a biogas plant.
3.
Step
4
1.
Explain the technology to generate hydroelectricity.
2.
Explain the construction of a biogas plant.
3.
Explain the method of biogas production from a biogas plant.
4.
Explain biomass briquetting technology.
Multiple choice questions (MCQs)
1.
Which of the following is a renewable source of energy?
a.
wood
b. petroleum
c. natural gas
d. uranium
Which of the following is not an alternative source of energy?
2.
0
60
a.
coal
b. briquette
c.
solar energy
d. tidal energy
Optional Science - 10
P HYS I CS
3.
Biogas is a mixture of gases like
1.
2.
3.
ethane, sulphur dioxide, hydrogen and hydrogen sulphide
ethane, nitrogen dioxide, oxygenand hydrogen sulphide
methane, carbon dioxide, oxygen and hydrogen sulphide
4. methane, carbon dioxide, hydrogen and hydrogen sulphide
Which of the following briquette is most popular in Nepal?
4.
a.
coal briquettes
b. peat briquettes
c. biomass briquettes
d. paper briquettes
The main possible source of energy in our country is
5.
a.
hydroelectricity
b. nuclear energy
c. tidal energy
d. geothermal energy
Normally the rate of increase in the temperature below the earth's surface in the first 10
km is
6.
a.
7.
80 °C per km
b. 30 °C per km
c. 20 °C per km
Biomass includes
d. 40 °C per km
a.
c.
b. wood, cow dung, agricultural waste
d. unused metal pieces, paper, straw
wood, cow dung, paper plastic
Paper, plastic, old wires
Project Work
1.
Make a model of a turbine and rotate it with the help of the wind at high speed.
2.
To make a paper briquettes
3.
Place four handfuls of shredded paper into a standard-size mixture. Pour in about 2 cups
of water.
4.
Run your mixture5-10 seconds until the paper is pulpy.
5.
Pour the mixture into a sieve over the sink. Allow it to strain out most of the water. Apply
a great deal of pressure to remove excess water and properly compress the pulp. Place
it in a sunny, dry location. Allow it to dry thoroughly; which may take as long as a week.
P HYS I CS
Optional Science - 10
61
UNIT
4
HEAT
Joseph Black (1728-1799) was a Scottish physician and chemist, known for his discoveries
of magnesium, latent heat, specific heat and carbon dioxide. He attended grammar school
in Belfast at the age of 12 and entered the University of Glasgow in 1746 when he was 18,
studying there for four years before spending another four at the University of Edinburgh,
furthering his medical studies. He was Professor of Anatomy and Chemistry at the University
of Glasgow for 10 years from 1756, and then Professor of Medicine and Chemistry at the
University of Edinburgh from 1766, teaching and lecturing there for more than 30 years.
In 1761, he deduced that the application of heat to ice and boiling water caused a volume
change without change in temperature. He concluded that the heat applied must have
combined with the ice particles and boiling water and become latent.
Key terms and terminologies of the unit
Key terms and terminologies of the unit
1.
Melting/fusion: The change from a solid to a liquid phase at a constant
temperature is called melting or fusion.
2.
Boiling/vaporization: The change of state of a material from liquid to gas on
heating at a constant temperature is called boiling or vaporization.
3.
Condensation: The change of a substance from its gaseous form (e.g. water vapor)
into liquid form (e.g. water) is called condensation.
4.
Solidification/freezing: The change of a substance from its liquid form (e.g.
water) to solid form (e.g. ice) is called solidification or freezing.
5.
Sublimation: The change from a solid to a vapor state without passing through
the liquid state is called sublimation.
6.
Deposition: The change from a gaseous to a solid state without passing through
the liquid state is called deposition.
7.
Phase change diagram: A phase change diagram is the representation of phase
transformation and also the conditions of transformation of a matter.
8.
Latent heat: Latent heat of a substance is the amount of thermal energy absorbed
or released by a substance during a change in its physical state that occurs without
0
62
Optional Science - 10
P HYS I CS
changing its temperature.
9.
Specific latent heat: The amount of heat energy absorbed or released to change
the phase of a unit mass of a substance without changing its temperature is called
specific latent heat.
10.
Latent heat of fusion: The heat energy required to convert a solid at its melting
point into liquid without any rise in the temperature is called latent heat of fusion.
11.
Specific latent heat of fusion: The heat required to change a unit mass of a solid
to liquid at its melting point is called specific latent heat of fusion of the solid.
12.
Latent heat of vaporization: The heat energy required to convert a liquid at its
boiling point into gas without any rise in the temperature is called latent heat of
vaporization.
13.
Specific latent heat of vaporization: The quantity of heat required to change a
unit mass of a liquid to a gaseous phase at constant temperature is called specific
latent heat of vaporization of the liquid.
14.
Latent heat of sublimation: The heat absorbed by a substance, which directly
changes from a solid to a gaseous state, or the heat given out by a gaseous substance
when it directly changes into a solid is called the latent heat of sublimation.
15.
Heat equation: The amount of heat gained or lost by a body (Q) is equal to the
product of its mass (m), specific heat capacity (s) and change in its temperature
(∆t). i.e. Q = ms∆t, This is called the heat equation.
16.
Principle of calorimetry: According to the principle of calorimetry, if there is no
loss of heat while mixing two substances at different temperatures, the amount of
heat lost by the body at high temperature is equal to the amount of heat gained by
the body at low temperature.
Introduction
All matters have atoms or molecules with a certain molecular Liquid
attraction called intermolecular force of attraction. Such a force of
attraction is called a bond that holds the atoms together. At normal
Gas
room temperature, it possesses certain kinetic energy too. Whenever
the kinetic energy of atoms or molecules in a substance increases,
Solid
it becomes warmer. Heat is a form of energy caused by the motion
of atoms and molecules. Actually the substances do not contain
heat but have internal energy. The internal energy is the sum of the
fig:states of water
kinetic energy of all the molecules in a substance. When heat flows, the internal energy of a hot
substance decreases, and the internal energy of a cold substance increases.
Memory Plus
The sum of the kinetic energy of all the atoms or molecules in a substance gives heat.
But the average kinetic energy of all the atoms or molecules in a substance gives its
temperature. When matter gets warmer, the atoms or molecules in the matter move faster.
P HYS I CS
Optional Science - 10
63
External source of energy can change the configuration of atoms or molecules in a matter. If
enough heat is transferred to a body, then the bonds will break and the molecules will change
the state of the body. In this unit, we will learn about the hidden heat during the change of
phase of a matter, called latent heat, heat equation to calculate the heat gained or released by
a body, and the principle of calorimetry.
Memory Plus
The SI unit of heat is the joule (J) and a more common unit of heat is the calorie. The
amount of heat required to raise the temperature of 1 gram of water by 10C is called
one calorie heat. Kilocalorie (kcal) is the bigger unit of heat. One kilocalorie is the heat
required to raise the temperature of 1 kg of water by 10C.
1 calorie = 4.2 joules
1 kilocalorie = 1000 calories = 4200 joules
Change of state
Matter can exist in three states, namely solid, liquid
and gas. These states are also called phases. When a
solid substance changes from a solid phase to a liquid
phase, energy must be supplied in order to overcome the
molecular attraction between the constituent particles of
the solid. That is, energy is needed to break the bonds
when a substance melts or boils. The state of matter can
be changed by changing the temperature or pressure.
I
.
Heat
I
Ice (s)
Heat
Water (l)
Steam (g)
fig:change of state of water
When heated, the rigid molecular structure in a solid breaks down to liquid state, and the
liquid to gaseous state on further heating. Conversely, when energy is released, then gas
changes into liquid, and liquid changes back to solid. For example, water exists in all three
states. On heating, ice changes into water. Water changes into steam on further heating. In
reverse order, steam changes into water on cooling. On further cooling, water changes into ice
again.
Types of phase transition
The following phase changes can be observed in matter:
1.
Melting or fusion: When heat is given to ice, it melts and
forms water. The change from a solid to a liquid phase at
a constant temperature is called melting or fusion. The
temperature at which melting occurs is called the melting
point of a solid. Heat is released from the solid in this process.
Solid
Melting
Memory Plus
The temperature at which a solid melts at 1 atmosphere of pressure (760 mmHg) is
called normal melting point. The normal melting point of ice is 0°C.
64
Optional Science - 10
P HYS I CS
2.
Boiling or vaporization: On further heating of water, it changes into steam (vapor). The
change of state of a material from liquid to gas on heating at a constant temperature is
called boiling or vaporization. The temperature at which boiling occurs is called the
boiling point of liquid. Heat is absorbed by a liquid from outside in this process.
Memory Plus
The temperature at which a liquid boils at 1 atmosphere of pressure (760 mmHg) is
called the normal boiling point. The normal boiling point of water is 100 °C.
If the pressure decreases, then water will boil at a temperature lower than 100°C. The
boiling point of water decreases by 1°C every 300 m of height increase above sea level.
Differences between melting and boiling
I-
Melting
~
I
-1
Boiling
It is the change of state of matter from solid It is the change of state of matter from
to liquid.
liquid to gas.
Heat is released from the solid in this Heat is absorbed by the liquid from
process.
I outside in this process.
__J
I
3.
Condensation: On cooling steam or water vapor, it changes into water. The change of a
substance from its gaseous form (e.g. water vapor) into liquid form (e.g. water) is called
condensation.
Know the Reason
There are water droplets on the surface of a cold soda bottle on a humid day, why?
On a humid day, water molecules in the air, as vapor, hit the colder surface of the
soda bottle and get condensed to form water droplets. So there are water droplets on
the surface of a cold soda bottle on a humid day.
4.
Solidification or freezing: On cooling water, it changes into ice.The change of a
substance from its liquid form (e.g. water) into solid form (e.g. ice) is called solidification
or freezing.
5.
Sublimation: The change from a solid state to a vapor state without passing through
the liquid state is called sublimation, and the substance is said to sublime. For example,
dry ice, camphor and iodine. Energy is required for a solid to sublime into gas.
6.
Deposition: The change from a gaseous state to a solid state without passing through
the liquid state is called deposition. For example, in subfreezing air, water vapor changes
directly to ice without first becoming a liquid. The process of deposition releases energy.
Latent heat
There is change in the temperature of ice and water when they are heated. But when ice
changes into water or water changes into steam, there is just change in the volume of water
or steam without rise in the temperature although heat is supplied continuously. Contrary to
this, when steam is cooled to water and then into ice, there is no fall in the temperature during
the change of state. Such hidden heat is termed as latent heat.
P HYS I CS
Optional Science - 10
65
The term ‘latent heat’ was introduced around 1761 by Scottish chemist Joseph Black. It is
derived from the Latin word, ‘latere’, meaning ‘to lie hidden’. In 1761, Black deduced that the
application of heat to ice at its melting point does not cause a rise in the temperature of the
ice/water mixture, but rather an increase in the amount of water in the mixture. Additionally,
Black observed that the application of heat to boiling water does not result in a rise in the
temperature of the water/steam mixture, but rather in an increase in the amount of steam.
From these observations, he concluded that the heat applied must have combined with the ice
particles and boiling water and become latent.
Latent heat of a substance is the amount of thermal energy absorbed or released by the
substance during the change in its physical state that occurs without changing its temperature.
The SI unit of latent heat is joule (J).
Explanation of latent heat on the basis of kinetic theory
There are many atoms or molecules in a substance. They have intermolecular forces of
attraction. To increase the temperature of a substance, there should be an increase in kinetic
energy of the molecules. But the heat supplied during phase transition does not increase the
kinetic energy of the molecules, and hence there is no rise in the temperature of the substance
during phase transition. Thus, the latent heat is used up in overcoming the force of attraction
among the molecules of the substance instead of giving a rise in the temperature.
Know the Reason
The temperature of a material does not change during the change of phase, why?
Heat supplied during the change of phase is used up in overcoming the force of attraction
among the molecules of the substance instead of giving a rise in the temperature. So the
temperature of a material does not change during the change of phase.
Calculation of heat absorbed or given out during change of state of a substance
Let ‘Q’ be the amount of heat absorbed during the change of state of a substance of mass ‘m’. It
is experimentally found that the quantity of heat absorbed or given out by a substance during
its change of state is directly proportional to the mass of the substance. That is,
Qαm
∴
Q=L×m
Or,
Q = mL
Where, L is a constant called ‘specific latent heat’ of the substance. Its value depends only on
the nature of the substance.
∴
Amount of heat absorbed or given out during phase transition = Mass of the substance
× Specific latent heat of the substance
Specific latent heat
The amount of heat energy absorbed or released to change the phase of unit mass of a substance
without changing its temperature is called specific latent heat. It is generally represented by
the letter L and expressed as
L=
0
66
Q
, where ‘Q’ is the heat supplied and ‘m’ is the mass of the substance.
m
Optional Science - 10
P HYS I CS
Units of specific latent heat
Q
, the SI unit of heat is the joule and that of the mass is the kilogram. So the SI unit
m
of specific latent heat is joules per kilogram (J/kg).
Since L =
Other common units are calories per gram (cal/g), kilocalories per gram (kcal/g) and joule per
gram (J/g).
Types of latent heat
Latent heat can be categorized as latent heat of fusion, latent heat of vaporization and latent
heat of sublimation.
Latent heat of fusion
The heat energy required to convert a solid at its melting point into liquid without any rise in
the temperature is called latent heat of fusion. It is required to break the bonds between solid
molecules. Latent heat of fusion is associated with melting of a solid or freezing of a liquid.
During melting of a solid, latent heat of fusion is absorbed from outside, and at the time of
freezing the same amount of heat is given out.
Specific latent heat of fusion
The heat required to change a unit mass of a solid to liquid at its melting point is called specific
latent heat of fusion of the solid. It is denoted by Lf or simply by L.
Thus, if Q is the quantity of heat required to melt a mass of ‘m’ of a solid substance completely
into liquid, then the latent heat of fusion for the substance is
Lf or L =
Quantity of heat absorbed during melting
mass of the solid substance melted
Q
m
The SI unit of specific latent heat of fusion is joule per kilogram (J/kg).
L=
Values of the specific latent heat of fusion and melting point for some common substances
Substance
Specific latent heat of fusion
Melting point ( in oC)
In SI units (J/kg)
In cal/g
Aluminium
3.97× 105
94.52
658
Ice
3.36× 105
80
0
Copper
5
1.80 × 10
43
1083
Zinc
5
1.34× 10
31.9
420
Silver
0.882 × 10
21
961
Gold
0.644 × 10
15.33
1063
Lead
0.25 × 105
6
327.3
5
5
Solved numerical:
The phase change diagram for a solid of mass 200g is shown in the
given figure. Find
1.
Melting point
2.
Specific latent heat of fusion of the substance.
P HYS I CS
Temperature (oC)
D
420
320
B
C
A
900
1500 1800
Heat (J)
Optional Science - 10
0
67
Solution:
Here, mass of the substance (m) =200 g =
i.
200
= 0.2 kg
1000
Form the phase change diagram, BC represents the melting of the solid at 320oC.
Thus, the melting point of the given solid is 320oC.
ii.
Heat at ‘B’ = 900 J, Heat at ‘C’ = 1500J
The amount of heat absorbed during melting (Q) = 1500-900 = 600 J
Now, the latent heat of fusion is given by
Or
Q = mL
L=
Q
600
=
= 3000J/kg
m
0.2
Therefore, the latent heat of fusion of the given solid is 3000 J/kg.
1.
Specific latent heat of fusion of ice:
Activity:
i.
Take some crushed ice in a beaker and note its temperature with the help of a
laboratory thermometer. Is it 00C? Otherwise let the ice melt first.
ii.
Now heat these pieces of ice by using a small flame. Note the temperature after
every minute. Do you find a constant temperature?
On heating of ice at 0oC continuously, it melts to form water, but the thermometer shows the same
temperature. Hence, there is no rise in the temperature during melting of ice even if heat
is being supplied continuously.
The energy that a unit mass of ice at 0oC absorbs from its surrounding in order to overcome the
attractive forces between its molecules when it changes from ice to water at 0oC is called specific
latent heat of fusion of ice. It is experimentally found that 3.36× 105 joules of heat energy is
required to convert 1 kg of ice at its melting point to water at the same temperature. That is, the
specific latent heat of fusion of ice is 3.36×105 J/kg.
Memory Plus
When ice at 0°C melts, the water formed with the latent heat of fusion of ice is also at 0°C.
Specific latent heat of fusion of ice is 3.36 × 105 J/kg means that 3.36 × 105 J of heat is required
to change one kilogram of ice at 0°C into water at the same temperature, or 3.36×105 J of
heat is given out when 1 kg of water at 0°C freezes into ice at the same temperature.
Solved numerical
Calculate the amount of heat required to convert 500g of ice at 0oC into water at the same
temperature. (Specific Latent heat of ice = 3.36× 105 J/kg)
Solution:
500
= 0.5 kg
1000
Specific latent heat of ice (L) = 3.36× 105 J/kg
Here, mass of ice (m) = 500 g =
The heat absorbed during phase transition is given by,
68
Optional Science - 10
P HYS I CS
Q=m×L
Q = 0.5× 3.36× 105 = 1.68× 105 J
∴
The heat required is 1.67× 105 J.
Phase change diagram
3.
C
10
A
Ice melting
(solid + liquid)
(liq
uid
)
20
wa
ter
In this graph, point A represents ice. When heat is
supplied to this ice, its temperature does not rise even
though heat is continuously supplied. Change of phase
in which ice changes into water is represented by AB.
The temperature of a mixture of water and ice is 0oC. At
B, all ice has melted. On further heating beyond B, the
temperature of water increases along BC.
Temperature in ᵒC
2.
Or,
B
Time of heating (in minutes)
-
Consequences of high specific latent heat of fusion of ice
Ice has high specific latent heat of fusion (i.e., 3.36×105 J/kg). The following are the
consequences of the high specific latent heat of fusion of ice:
i.
Snow is formed due to freezing of water vapor in the atmosphere. During freezing,
every 1 kg of water at 0oC gives out 3.36×105 J of heat to the surrounding. It makes
the surrounding weather moderate during snowfall.
ii.
Snow in the Himalayan region melts slowly. Therefore, water flows continuously
in perennial rivers.
Know the Reason
Ice at 0°C appears to be colder in our mouth than water at the same temperature, why?
When ice at 0°C changes into water at 0°C, it absorbs heat equivalent to the specific latent
heat of fusion of ice (3.36× 105J/kg). But this extra heat is not absorbed by the ice at 0°C. So
ice at 0°C appears to be colder in our mouth than water at the same temperature.
Latent heat of vaporization
The heat energy required to convert a liquid at its boiling point into gas without any rise
in the temperature is called latent heat of vaporization. It is required to break the bonds
between liquid molecules. Latent heat of vaporization is associated with boiling of a liquid
or condensation of a liquid. When boiling a liquid, the latent heat of vaporization is absorbed
from outside, and at the time of condensation, the same amount of heat is given out.
Specific latent heat of vaporization
The quantity of heat required to change a unit mass of a liquid to the gaseous phase at constant
temperature is called specific latent heat of vaporization of the liquid. It is denoted by Lvap or
simply by L.
Thus, if Q is the quantity of heat required to boil a mass ‘m’ of a liquid substance completely
into vapor, then the latent heat of vaporization for the substance is
Quantity of heat absorbed during boiling Q
=
mass of the solid substance vaporized m
The SI unit of specific latent heat of vaporization is joule per kilogram (J/kg).
Lvap or L =
P HYS I CS
Optional Science - 10
69
Values of the specific latent heat of vaporization and boiling point for some common substances
-
Specific latent heat of vaporization
Substance
In SIunits (J/kg)
I
In cal/g
Boiling point ( in oC)
Water
22.68× 105
540
1000C
Ethyl alcohol
8.5 × 105
202.38
780C
Sulphuric acid
5.1 × 105
121.43
3380C
Ether
3.9 × 105
92.86
34.50C
Mercury
2.8 × 105
66.67
3570C
~
1.
I
Specific latent heat of vaporization of water:
-
-
Activity:
i.
Put some amount of water in a beaker and heat it to a boil. Measure the temperature
of the water with the help of a laboratory thermometer as it starts boiling. Is it
1000C?
ii.
Note the temperature of boiling water after every minute. Do you find a constant
temperature?
iii.
On heating water at 100oC continuously, it boils to form steam, but the thermometer
shows the same temperature. Hence, there is no rise in temperature during boiling
of water even if heat is being supplied continuously.
The energy that a unit mass of water at 100oC absorbs from its surrounding in order to overcome
the attractive forces between its molecules when it changes from water to steam at 100oC is
called specific latent heat of vaporization of water. It is experimentally found that 22.68× 105
joules of heat energy is required to convert 1 kg of water at its boiling point to steam at the same
temperature. That is, the specific latent heat of vaporization of water is 22.68×105 J/kg.
Memory Plus
When water at 100°C boils, the steam formed with the latent heat of vaporization of water
is also at 100°C.
Specific latent heat of vaporization of water is 22.6×105 J/kg means that 22.68×105 J of heat
is required to change one kilogram of water at 100oC into steam at the same temperature,
or 22.68×105 J of heat is given out when 1 kg of steam at 100°C gets condensed into water
at the same temperature.
Know the Reason
When water in a pot is kept boiling, the temperature remains at 100 °C (212 °F) until the
last drop get vaporized, why?
All the heat being added to the boiling water is absorbed as latent heat of vaporization
and carried away by the escaping vapor molecules. So when water in a pot is kept boiling,
the temperature remains at 100 °C (212 °F) until the last drop get vaporized.
0
70
Optional Science - 10
P HYS I CS
Phase change diagram
3.
150
B
wa
ter
ui
d)
100
20
Vaporization
(Or boiling)
st
ea
m
(v
ap
ou
r)
D
t
C
Liquid + vapour
(li
q
In this graph, AB represents water and point B
represents water at 100oC. When heat is supplied
to this water, its temperature does not rise even
though heat is continuously supplied. Change
of phase in which water changes into steam is
represented by BC. The temperature of a mixture
of water and steam is 100oC. At C, all water has
vaporized. On further heating beyond C, the
temperature of steam increases along CD.
Temperature (inᵒC)
2.
A
Time of heating (in minutes)
Some consequences of high specific latent heat of vaporization of water
Water has high specific latent heat of vaporization (i.e., 22.68×105 J/kg). The following
are the consequences of high specific latent heat of vaporization of water:
i.
Evaporation of water from a surface removes excess heat energy. This causes the
cooling effect of leaves, removes body heat through sweating and protects an
organism from sudden temperature fluctuations (i.e., thermal shock).
ii.
Every 1kg of water at 100°C absorbs 22.68×105 J of heat when it changes into steam
at the same temperature. So when water is used as a cooling agent for a combustion
engine, steam absorbs a large amount of heat energy from a hot engine.
Know the Reason
Skin burn from 100oC steam is more severe than a burn from water at 100oC, why?
When water at 100°C changes into steam at 100°C, it absorbs heat equivalent to the specific
latent heat of vaporization of water (22.68× 105 J/kg). But this extra heat is not absorbed
by water at 100°C. So skin burn from 100°C steam is more severe than a burn from water
at 100°C.
Latent heat of sublimation
Sublimation is a physical process in which a solid directly converts into a gaseous (vapor)
state without going through a liquid state. The heat absorbed by a substance, which directly
changes from a solid to a gaseous state, or the heat given out by a gaseous substance when it
directly changes into a solid, is called the latent heat of sublimation.
Heat equation
Change in temperature of a body is either due to absorption of heat or due to the release of
heat. On heating body, it absorbs heat and its temperature rises but when a body gets cooled,
it gives out heat. This results in decrease in temperature of the body.
Let us consider the temperature of a body of mass ‘m’ and specific heat capacity 's' rises from
initial temperture (t1 )to final temperature (t2), when it is heated by supplying ‘Q’ amount of
heat.
Experimently it has been proved that, the heat gained or lost (Q) is directly proportional to:
Mass of the body (m), i.e.,
Qαm
………. (i)
P HYS I CS
Optional Science - 10
71
Change in the temperature (∆t), i.e.,
Q α ∆t
………. (ii)
Combining relation (i) and relation (ii)
Q α m ∆t
Q = ms∆t, where ‘s’ is a proportionality constant called specific heat capacity.
Thus, the amount of heat gained or lost by a body (Q) is equal to the product of its
mass (m), specific heat capacity (s) and change in its temperature (∆t), i.e. Q= ms∆t,
This is called the heat equation.
Solved numerical- 4.
Specific heat capacity of water is 4200 J kg-1oC-1. Calculate the amount of heat energy given out
when 5 kg of water cools down from 80oC to 30oC.
Solution:
Here, Specific heat capacity of water (s) = 4200 J kg-1oC-1
Mass of water (m) = 5 kg
Initial temperature (θ1) = 80o C
Final temperature (θ2) = 30o C
Change in temperature (∆t) = θ1 – θ2 = 80o C – 30o C = 50o C
Now, heat energy lost, Q = ms ∆t
Or, Q = 5 × 4200 × 50
∴ Q = 1050000J = 1.05 × 106 J
Principle of calorimetry
The branch of physics which deals with the measurement of heat energy is called calorimetry.
When two bodies of different temperatures are kept in thermal contact, heat flows from a
body at high temperature to a body at low temperature. Heat lost or gained is measured using
a calorimeter. A calorimeter is acylindrical container made ofcopper or aluminium. Its outer
surface is kept shining to prevent the exchange of heat between the container and the
surrounding. The arrangement is kept in a hollow wooden box. The gap between the container
and the box is filled in by non-conductors of heat like wool, cotton, etc. The stirrer kept in the
device is used to stir the mixture for uniform distribution of heat.
In winter, people mix hot water with cold water for bathing. The
temperature of the mixture is less than the temperature of hot water
and more than the temperature of cold water. In this process, the hot
water loses heat, and the cold water gains the heat lost, and finally the
mixture attains a common temperature. According to the principle of
calorimetry, if there is no loss of heat while mixing two substances at
different temperatures, the amount of heat lost by the body at high
temperature is equal to the amount of heat gained by the body at low
temperature.
Thermometer
Stirrer
vessel
Reaction
mixture
fig:Calorimeter
Thus, heat lost by the body at high temperature = heat gained by the body at low temperature
Or,
0
72
m1 s1 (θ1– θ) = m2 s2 (θ– θ2)
Optional Science - 10
P HYS I CS
Where, θ = final temperature of the mixture
m₁ = mass of the hotter body
m₂ = mass of the colder body
s₁ = specific heat capacity of hotter body
s₂ = specific heat capacity of colder body
θ1 = initial temperature of the body at high θ2 = initial temperature of the body at low
temperature
temperature
Solved numerical- 4.
100g of water at 1000C is mixed with 200g of water. If the temperature of the mixture becomes
500C, find the initial temperature of the cold water.
Solution
100
kg = 0.1 kg
1000
Initial temperature of hot water (θ1) = 1000C
Here, mass of hot water (m1) = 100g =
Mass of the cold water (m2) = 200g = 0.2kg
Final temperature of the mixture (θ) = 500C
Initial temperature of cold water (θ1) = ?
From the principle of calorimetry
Heat lost by hot water = Heat gained by cold water
Or, m1s (θ1 – θ) – m2s (θ2 – θ)
Or, 0.1 × (100 – 50) = 0.2 × (50 – θ2)
Or,
0.1 × 50
= 50 – θ2
0.2
∴ θ2 = 50 – 25 = 25°C
Therefore, the initial temperature of cold water is 250C.
Answer writing skill
1.
I
What causes latent heat?
The intermolecular force of attraction in different substances is the cause of latent heat.
2.
What is a calorimeter?
A device which measures heat lost or heat gained on mixing two substances at different
temperatures is called a calorimeter.
3.
How much heat is given out by 1kg steam at 100oC when it gets condensed into water
at the same temperature?
22.68 × 105 J of heat is given out when 1kg of steam at 100°C gets condensed into water
at the same temperature.
P HYS I CS
Optional Science - 10
0
73
4.
Write the relation between the heat energy absorbed and mass of a body.
Heat energy absorbed by a body is directly proportional to the mass of the body. If ‘Q’
is the heat absorbed and ‘m’ be the mass of the body then, Q α m.
5.
What is meant by
1.
The specific latent heat of fusion of ice is 80 cal/g?
The specific latent heat of fusion of ice is 80 calories per gram means that 80
calories of heat are absorbed by each gram of ice at 0oC on melting or 80 calories
of heat are given out by 1g of water at 0oC during freezing.
2.
The specific latent heat of vaporization of water is 540 cal/g?
The specific latent heat of vaporization of steam is 540 calories per gram means
that 540 calories of heat are absorbed by each gram of water at 100oC on boiling or
540 calories of heat are given out by 1g of steam at 100oC during condensation.
6.
Write the differences between evaporation and vaporization
Evaporation
7.
Vaporization
It occurs at all temperatures.
It occurs only at boiling point
It is a slow process.
It is a rapid process.
It occurs only on the surface of a liquid.
It occurs over the entire volume of a liquid.
It causes cooling of the atmosphere.
It does not cause cooling of the atmosphere.
How does the temperature of air remain moderate during snowfall?
Snow is formed due to freezing of water vapour in the atmosphere. During freezing,
every 1kg of water at 0°C gives out 3.36×105 J of heat to the surrounding. It makes the
surrounding weather moderate during snowfall.
8.
What are the different phases of water shown in the given phase diagram?
First phase: Water at temperature less than 100oC to
water at 100oC temperature.
100ᵒC
2.
Second phase: Water at 100 C to steam at 100 C
temperature.
0
o
3.
---r
T(ᵒC)
1.
o
steam
water + steam
water
t (in min)
-10
Third phase: Steam at 100oC to steam greater than
100oC temperature.
Calculate the heat energy released when an iron ball of 5 kg mass is cooled down from
430°C to 30°C? How much mass of water can be heated from 30°C to 100°C by this heat
energy? The specific heat capacity of iron and water are 460 J/kg°C and 4200 J/kg°C
respectively.
9.
Here, mass of iron ball (m) = 5kg
Initial temperature (t1) = 430°C
Final temperature (t2) = 30°C
Change in temperature (dt) = 430°C– 30°C = 400°C
0
74
Optional Science - 10
P HYS I CS
Specific heat capacity of iron (s) = 460 J/kg°C
According to the heat equation, the heat released is given by
Q = ms dt
Q = 5 × 460 × 400 = 920000 J
Again, specific heat capacity of water (s) = 4200 J/kgoC
Mass of water (m) = ?
Initial temperature (t1) = 30°C
Final temperature (t2) = 100°C
Change in temperature (dt) = 100 – 30 = 70
Heat supplied (Q) = 920,000 J
Now, heat energy supplied, Q = ms dt
Or, 920,000 = m × 4200 × 70
Or, m =
10.
920000
4200 × 70
= 3.129 kg
Prove that the amount of heat gained or lost by a body (Q) is equal to the product of its
mass (m), specific heat capacity (s) and change in its temperature (dt), i.e., Q = md dt.
The heat gained or lost (Q) is directly proportional to:
i.e.,
Qαm
mass of the body (m),
……. (i)
change in temperature (∆t), i.e.,
Q α ∆t
……. (ii)
Combining relation (i) and relation (ii)
Q = ms ∆t, where ‘s’ is a proportionality constant called specific heat capacity.
Thus, the amount of heat gained or lost by a body (Q) is equal to the product of its mass
(m), specific heat capacity (s) and change in its temperature (∆t), i.e. Q = ms ∆t, This is
called the heat equation.
P HYS I CS
Optional Science - 10
0
75
Exercise
Step
1
Define
1. One calorie heat
2. melting 3. freezing
4. vaporization
5. condensation 6. sublimation
7. deposition
8. latent heat of fusion 9. latent heat of vaporization
10. latent heat of sublimation
Very short answer questions
1.
Name three states of matter.
2.
Write two factors which can change the state of matter.
3.
Write SI unit of the following
a. latent heat
b. specific latent heat of fusion
4.
How much heat is required to change one kilogram of ice at 0oC into water at the same
temperature?
5.
How much heat is required to change one kilogram of water at 100oC into steam at the
same temperature?
6.
Write the formula to calculate the heat absorbed or given out during the change of state
of a substance.
Step
2
Short answer questions
1.
Write an example of each of the following
a. melting
b. freezing
c. vaporization
e. sublimation
f. deposition
76
Optional Science - 10
P HYS I CS
d. condensation
2.
During melting, there is no increase in the temperature of ice even though heat is being
supplied continuously. Where is the applied heat used?
3.
Write some consequences of high specific latent heat of fusion of ice.
4.
Write some consequences of high specific latent heat of vaporization of water.
5.
What is a heat equation? Write its mathematical form, too.
Differentiate between
1.
Melting and boiling
2.
Normal melting point and normal boiling point
3.
Latent heat of fusion and latent heat of vaporization
4.
Sublimation and deposition
Give reason
1.
There are water droplets on the surface of a cold soda bottle on a humid day.
2.
Temperature of a material does not change during change of phase.
3.
Ice at 0°C appears to be colder in our mouth than water at the same temperature.
4.
When a pot of water is kept boiling, the temperature remains at 100°C (212°F) until the
last drop evaporates.
5.
Skin burn from 100°C steam is more severe than a burn from water at 100°C.
Answer the questions with the help of the given figure
2.
The phase change diagram shows how the temperature of a pure substance changes on
heating.
2.
At what temperature does the substance
boil?
3
Label the parts of the graph which represent
different phases of the substance.
150
D
t
B
100
C
)
What is the initial value of temperature of
the substance?
20
(li
qu
id
1.
Temperature (inᵒC)
1.
A
Time of heating (in minutes)
--
The phase change diagram for a solid of mass 500g
r
is shown in the given figure. Find
1.
melting point
2.
Specific latent heat of fusion of the
substance.
3.
boiling point
4.
Specific latent heat of vaporization
D
6.7
9.7
Temp (T)
10oC
O
P HYS I CS
C
--------------~
130oC
B
A
''
3.3
''
Heat energy (kJ)
Optional Science - 10
0
77
Step
3
Numerical problems
1.
The specific latent heat of fusion of ice is 336000 J/kg. Find the mass of the ice at 0°C
which requires heat of 168000 J to melt completely into water at 0°C. Ans: 0.5 kg
2.
Calculate the quantity of heat required to convert 500g of ice at 0°C into water at a
temperature of 0°C. (Specific latent heat of fusion of ice = 336000 J/kg )Ans: 1.008× 105 J
3.
Calculate the quantity of heat required to convert 450g of water at 100°C into water
vapor at the same temperature. (Specific latent heat of vaporization of water = 22.68 × 105
J/kg)
Ans: 10.206×105 J
4.
How much heat must be added to raise the temperature of 200g of water from 15°C to
85°C?
Ans: 58800 J
What will be the quantity of heat required to raise the temperature of 2kg paraffin by
100C if 44000 joules of heat energy are required to raise the temperature of the paraffin
by 20°C?
Ans: 4.4× 104 J
An electrical kettle contains 200g of water at 200C. How much heat is to be supplied in
order to boil the water? (Assume that the kettle takes no heat) Ans: 67200 J
A brass rod of 0.4 kg mass at 100°C is dropped into 1.0 kg of water at 20°C. The final
temperature is 23°C. Calculate the specific heat capacity of brass. (Specific heat capacity
of water = 4200 J/kg°C)
Ans: 409.09 J/kgoC.
A bucket contains 8kg of water at 25°C. Calculate the final temperature of the water if
2kg of water at 80°C is poured into it. (Neglect the heat loss)
Ans: 36°C
When a 200g hot iron sphere is kept in 500g of water at 10°C, then the final temperature
of water becomes 30°C. Find the initial temperature of the iron sphere. (Specific heat
capacity of iron = 470 J/kg°C)
Ans: 476.8°C
5.
6.
7.
8.
10.
Draw a diagram
1.
To show the phase change which occurs when ice is heated and completely changes into
steam.
2.
To show different types of phase transitions.
Step
4
1.
2.
3.
4.
5.
Derive heat equation, Q = ms ∆t , where the symbols have their usual meaning.
Explain an experiment to demonstrate latent heat of fusion.
How can you demonstrate latent heat of vaporization? Explain.
Explain latent heat on the basis of kinetic theory.
Which type of changes do you observe on complete heating of ice into steam? Explain.
6.
Explain the factors which affect amount of heat energy.
0
78
Optional Science - 10
P HYS I CS
Multiple choice question (MCQs)
1.
During change of state, which of the following is true for molecules of a substance?
a. kinetic energy increases
b. potential energy increases
c.
2.
both increases
d. both remain constant
Snowballs are formed due to
3.
a.
melting of ice
b. freezing of moisture
c.
sublimation
d. deposition
Specific latent heat of fusion of ice is
4.
a.
80 kcal/g
b. 80 cal/g
c.
80 J/g
d. 80 J/kg
Specific latent heat of vaporization of water is
a.
405 cal/g
b. 504 cal/g
c. 540 cal/g
d. 450 cal/g
The SI unit of specific latent heat of fusion is
5.
6.
a.
J
b. J/kg
c.
cal
d. cal/g
The heat energy contained in a body depends upon:
a. mass
b. change in temperature
c. specific heat capacity
d. all the above
1kg of paraffin requires 44000 J heat energy to increase its temperature by 20oC, then its
specific heat capacity is
a. 2400 J /kgoC
b. 2200 J /kgoC
o
c. 2100 J /kg C
d. 2000 J /kgoC
7.
Project Work
1.
Take frozen ghee and ice cubes from a freezer and put them in two separate beakers.
Insert a laboratory thermometer inside both of them to measure their initial temperature.
Now heat them with a small flame and note their temperature every 30s. Find the melting
point of ice and ghee.
2.
Take three glass tumbler. Label them as A, B and C. Put 200ml of cold water in A and 200ml
of hot water in B. Measure their temperatures with the help of a laboratory thermometer.
Mix both of them in a thermos flask. Record the temperature of the water after mixing
them. Use the heat equation to make a rough estimate of the heat lost by the hot water
and the heat gained by the cold water. (Neglect the loss of heat to the surrounding).
P HYS I CS
Optional Science - 10
79
UNIT
5
LIGHT
Christiaan Huygens (1629-1695) was a Dutch mathematician, astronomer and physicist,
who founded the wave theory of light, discovered the true shape of the rings of Saturn, and
made original contributions to the science of dynamics. Huygens came from a wealthy and
distinguished middle-class family. His father was a diplomat and poet. From an early age,
Huygens showed a marked mechanical bent and a talent for drawing and mathematics. In
1645, Huygens entered the University of Leiden, where he studied mathematics and law. He
introduced correction in the construction of the telescope with his new method of grinding
and polishing lenses, which made it possible to discover the true shape of the rings of Saturn
in 1659. Using his improved telescope, he discovered a satellite of Saturn in March 1655 and
distinguished the stellar components of the Orion nebula in 1656.
Key terms and terminologies of the unit
1.
Lens: A lens is a piece of transparent optical material bounded by two refracting
surfaces.
2.
Convex lens: A lens which is thicker in the middle and thinner at the edges is
called a convex lens.
3.
Concave lens: A lens which is thinner in the middle and thicker at the edges is
called a concave lens.
4.
Power of a lens: The power of a lens is defined as the reciprocal of its focal length
(in metres).
5.
One dioptre power: The power of a lens whose focal length is one metre is called
one dioptre.
6.
Magnification: The ratio of the height of the image formed by a lens to the height
of the object placed in front of the lens is called magnification of the lens.
7.
Optical instrument: Optical instruments are devices which process light wave to
enhance an image for a clearer view.
8.
Compound microscope: An optical instrument for forming magnified images of
very small objects is called a compound microscope.
80
Optional Science - 10
P HYS I CS
9.
Astronomical telescope: Telescopes to get a clear view of the heavenly bodies are
called astronomical telescopes.
10.
Terrestrial telescope: A telescope which is used to observe distant objects on the
earth's surface is called a terrestrial telescope.
11.
Binoculars: Binoculars are hand-held optical instruments with two barrel
chambers mounted on a single frame side by side to provide a magnified view of
distant objects.
Introduction
Light is essential to see the colorful world around us. You had already learnt in lower classes
that the light which enters our eyes may be directly from a self-luminous object or it may be
the reflected light from a non-luminous object. Such light when falls on our eye's retina, then
we have a sensation of vision. Thus, light is a form of energy which produces the sensation of
vision. Light, when it passes from one medium to another, its direction gets changed. Such a
phenomenon in which light bends on passing from one medium to another medium is called
refraction of light. In class 9 optional science, you learnt about refraction of light and its cause.
You learnt about the bending of light through a glass slab, too. Similar bending of light occurs
through some other media like a glass prism, lens, etc. Here in this unit, you will learn about
lenses, magnification, power and optical instruments like a compound microscope, telescope
and binoculars.
Memory Plus
Light travels along a straight line. This property is called rectilinear propagation. The
straight line along which light travels is called a ray.
Refraction of light through lenses
Optical instruments like the camera, microscope, telescope work on the basis of refraction of
light through a lens. A lens is a piece of transparent optical material bounded by two refracting
surfaces. Generally, the transparent medium in a lens is of glass or clear plastic. The refracting
surfaces of lens are usually spherical. Lenses are used in making optical instruments like
cameras, compound microscopes, telescopes. A person with a vision defect wears spectacles
with a lens of a certain power.
Types of lenses
Lenses are made of different kinds of glass and come in a variety of shapes, but they belong to
either the converging group or diverging group. That is, lenses are of two types:
i.
Convex lens or converging lens
ii.
Concave lens or diverging lens
Convex lens
A lens which is thicker in the middle and thinner at the edges is called a convex lens. It bulges
out at the center. It helps the light rays to converge.
P HYS I CS
Optional Science - 10
0
81
Memory Plus
Types of convex lenses: There are three types of convex lenses.
1. Biconvex or double convex lens: Both of its surfaces are convex.
2. Plano-convex lens: It has one surface convex and the other surface a
plane.
3. Concavo- convex: It has one convex surface and the other surface a concave.
Double convex
Plano convex
Concavo convex
A convex lens as a group of prisms: Converging action of a convex lens
A convex lens is regarded as being made up of a large number of prisms.
The prisms on the upper half of the lens have their bases downward and the
prisms on the lower half have their bases upward. The angle of the prisms
goes on decreasing from the central line. The central part of the prism is just
like a glass slab.
In the case of a prism, the lesser the angle of a prism, the greater is the bending of light. Thus,
the light rays falling on the edges of a convex lens bend maximum. Finally, all the rays meet
at a point after refraction. This point is called the focus of the convex lens.
Know the Reason
A convex lens is called a converging lens, why?
A convex lens bends all the light rays falling on it inward. Therefore, all
the parallel beams of light converge at a point. So it is called a converging
lens.
A convex lens has a real focus, why?
The refracted rays from a convex lens actually meet at a point. So a convex lens has a real
focus.
It is dangerous to look through a convex lens at the sun or a bright light, why?
A convex lens converges the sunrays at one point. It increases the temperature at that
point. If we look through a convex lens at the sun on a bright sunny day, it can damage our
eyes. So it is dangerous to look through a convex lens at the sun or a bright light.
Uses of convex lens
1.
2.
3.
Convex lenses are used in optical instruments like compound microscopes, telescopes,
etc.
Convex lenses are used for image formation on film and slide projectors.
Memory
Plus
It is used to make searchlights and spotlights in theaters. A convex lens with a powerful
Types
of at
concave
lenses:
There
are three parallel
types ofbeam
concave
lamp
its focus
produces
a powerful
of light.
lenses:
4. 1. Biconcave
Convex lens
used for
correction
longof
sightedness.
orisdouble
concave
lens:ofBoth
its surfaces
arelens
concave.
Concave
2. Plano-concave lens: One surface of it is concave and the
A lens which is thinner in the middle and thicker at the edges isBiconcave
calledPlano-concave
a concave
lens. It is
Convexo-concave
other surface plane.
depressed at the center and the light rays are diverged when pass through it.
3. Convexo- concave: One surface of it is convex and the other surface concave.
TI ] ]
82
Optional Science - 10
P HYS I CS
A concave lens as a group of prisms: Diverging action of a concave lens
A concave lens is regarded as being made up of a large number of prisms. The prisms on the
upper half of the lens have their angles facing downward and the prisms on the lower half
have their angles facing upward. The angle of the prism continuously increases from the
central line towards the edges of the lens.
The light rays passing through a prism deviate towards its base. The lesser
the refracting angle, the greater the deviation produced. Thus, the light
rays near the edges of a convex lens deviate less while the light rays around
the central line of the lens deviate more. When all the diverged light rays
are produced backward, then they meet a point. This point is called the
principal focus of a concave lens.
Know the Reason
A concave lens is called a diverging lens, why?
A concave lens bends all the light rays falling on it outward. All the
parallel beams of light diverge, and the diverged rays appear as if they
are coming from a point. So it is called a diverging lens.
A concave lens has a virtual focus, why?
The refracted rays from a concave lens appear to diverge from a point. When we produce
them backward, they meet at a point which is the virtual focus. So a concave lens has a
virtual focus.
Memory Plus
Those lenses that are thicker in the middle converge parallel rays and those which are
thicker at the edges diverge parallel rays. Hence, light rays are always bent toward the
thicker part of a lens.
Uses of concave lens
1.
It is used as an eye lens in the Galileo Telescope.
2.
A concave lens is used for correction of short sightedness.
Power of a Lens
The power of a lens is a measure of the degree of convergence or divergence produced by it
when light rays fall on it. If a convex lens converges a parallel beam of light closer to its optical
center, then the focal length is less, but the converging power is high. Thus, the power of a lens
depends on its focal length. The power of a lens is defined as the reciprocal of its focal length
(in meters). Mathematically,
Power of lens (P) =
If the focal length is measured in centimeter
Power of lens (P) =
1
1
=
focal length (in metre) f
100
f (in cm)
P HYS I CS
Optional Science - 10
83
A convex lens has a positive focal length. So, the power of a convex lens is considered to be
positive. Whereas the focal length of a concave lens is negative. So, the power of a concave lens
is considered to be negative.
Know the Reason
The power of a lens is measured as a reciprocal of its focal length, why?
A thick lens with short focal length has more power to bend the light rays. But a thin lens
with long focal length has less power to bend the light rays. The power of a lens of short
focal length is more and vice-versa. So the power of a lens is measured as a reciprocal of
its focal length.
Unit of power of a lens
If the focal length of a lens is measured in meters, then the unit of power is meter-1, which is
called the diopter and denoted by the symbol 'D'.
One dioptre power: The power of a lens whose focal length is one meter is called 1 diopter.
Memory Plus
A lens of short focal length has more power whereas a lens of long focal length has less
power.
The power of a lens can be measured directly by using an instrument called adioptometer.
Opticians use it to measure the power of spectacle lenses.
A lens of power 3 D (diopter) means that the lens brings parallel rays of light to focus at 1/3
meters.
Solved numerical- 5.
A convex lens forms a real and inverted image of an object at a distance of 50 cm. How far
is the object from the lens if the image is equal to the size of the object? Also calculate the
power of the lens.
Solution: Here, image distance = 50 cm
If the image size is equal to the object size, then the object is at a distance double the
focal length (i.e., 2f)
In this case, image distance = object distance = 2f = 50 cm
25
m = 0.25 m
100
1
1
Now, power of a lens, P = =
=4D
f 0.25
f = 25cm =
Thus, the power of the convex lens is +4 D.
Combination of thin lenses
If two or more thin lenses are kept in contact, then the reciprocal of their equivalent
focal length is equal to the sum of the reciprocal of individual focal lengths of all
lenses. That is,
0
84
Optional Science - 10
P HYS I CS
combination
of lenses
1 1 1 1
= + + + .........
f f1 f2 f3
Where f1, f2, f3, ……. are the focal length of the thin lenses in contact.
Therefore, the power of the combination of thin lenses is given by
P = P1 + P2 + P3 + ..........
Where, P1=
Magnification
1
1
1
, P2= , P3= .........
f1
f2
f3
Magnification is the degree to which the object is enlarged during formation of its image by
using optical instruments like binoculars, microscope, etc.
Some examples of magnification
1.
A magnifying glass when placed close to an object produces an erect and magnified
image. Palmists use it to study the lines of a palm. It is also used as a reading glass.
2.
A telescope forms a magnified image of distant objects.
3.
A compound microscope makes a very small object appear much larger.
4.
In the case of a slide projector, it projects a large image of a small slide on a screen.
Calculation of magnification
When an image is longer than the object, we say it is magnified, and when it is smaller we
describe it as diminished. The ratio of the height of the image formed by a lens to the height of
the object placed in front of the lens is called the linear magnification of the lens.
Mathematically,
height of the image
magnification (m) =
height of the object
I
Or
m=
O
To obtain a relation involving object distance (u) and image distance (v):
In the given figure,
Convex lens
Height of the object (AB) = O
B
Height of the image (DC) = I
Object distance (OA) = u
2F
A
D
O
F
F
2F
Object
Image distance (OD) = v
C
In triangles AOB and COD:
u
v
S.N.
Statement
i.
Reason
AOB = COD Vertically opposite angles are equal.
ii.
OAB = CDO Both of them are right angles
iii.
ABO = OCD If two angles of a triangle are equal to two angles of another
triangle, then the third pair of angles are equal.
The triangles AOB and COD are similar.
In the case of the two similar triangles, the ratio of corresponding sides is equal, i.e.,
P HYS I CS
Optional Science - 10
0
85
DC OD
=
AB OA
I v
= =m
O u
So the magnification produced by a lens is also defined as the ratio of the image distance (v)
to the object distance (u).
Image distance
magnification (m) =
Object distance
v
Or
m=
u
Magnification has no unit, as it is a ratio of two distances.
Magnification (m)
Image size
'm' greater than 1 (m>1)
Magnified: larger than the object
'm' equal to 1 (m>1)
Image is of same size as the object
'm' less than 1 (m<1)
Diminished: smaller than the object
Solved Numerical- 5.
A convex lens forms an image of an object at a distance of 12 cm when the object is 6 cm from
the lens. Find the magnification of the image.
Solution: Here, object distance (u) = 6 cm
Image distance (v) = 12 cm
Now, magnification =
v 12
=
=2
u 6
Solved numerical- 5.
An object of height 2 cm is placed at a distance double that of the focal length of a convex lens.
Find the size of the image and its magnification.
Solution Here, size of the object (O) = 2 cm
When the object is placed at a distance double that of the focal length of a convex lens, then
Size of object (O) = Size of the image (I) = 2 cm
Now, magnification of image (m) =
I 2
= =1
O 2
Memory Plus
Magnification of a lens is expressed in number times (e.g. 10×). A lens has magnification of
10× means that the image formed is 10 times bigger than the object.
Optical instruments
Optical instruments are devices which process light waves to enhance an image for a clearer
view. For example, cameras, magnifying glasses, microscopes, telescopes, binoculars are
optical instruments. Such instruments form an image of an object with the help of the lens or
a number of lenses.
86
Optional Science - 10
P HYS I CS
Compound microscope
An optical instrument for forming magnified images of
very small objects is called a compound microscope. A high
power compound microscope achieves higher levels of
magnification and is used to observe or analyze microscopic
objects or organisms.
Construction: It consists of two convex lenses placed coaxially with two sliding tubes. The lens towards the object
is called objective, and it has a short focal length and a small
aperture. The lens through which the final image is observed
is called eye lens or eyepiece. The focal length of the eyepiece
is comparatively longer and the aperture is larger, too. The
objective lens and the eyepiece are arranged in such a way
that the distance between them can be adjusted.
Additional
Focusing
(interchangeable)
knob
objective lenses
Objective
lens
Light
source
fig:Compound microscope
Working: The object AB to be magnified is placed in between F and 2F of the objective lens. A
real, inverted and magnified image A'B' is formed in front of the eyepiece. A'B' acts as the
object for the eyepiece. The position of the eyepiece is adjusted to bring A'B' within its focus.
Finally, the eyepiece forms the magnified image A''B'' on the same side as A'B'.
Eyepiece
Objective
Object
A
Fo
B''
B
Fe
O
I2-Virtual, erect and
highly magnified
final image
A''
I1-Real, inverted
and enlarged
Fe B'
Eye
A'
fig: ray diagram to show the formation of image in a compound microscope
Uses of compound microscope:
1.
Diagnosis: A compound microscope is of great use in pathology labs to examine the
stool, blood and urine of patient. It helps to identify disease-causing agents and the
corresponding disease.
2.
Use in study and research: A compound microscope is used in a biology lab to observe
the cell structure and its organelles. Study through a microscope helps in research work,
too.
Telescope
The angle subtended at the eye by an object very far from our eye is small. So the object appears
small. To see the object nearer, the angle subtended by it at our eye should be increased. Such
a function is that of a telescope. A telescope is a device that is used to observe distant objects
either on the earth or in the heavenly bodies like the moon and planets. There are two types of
telescopes, namely astronomical telescope and terrestrial telescope.
P HYS I CS
Optional Science - 10
0
87
Astronomical telescope
A telescopes for getting a clear view of the heavenly bodies is called an astronomical telescope.
It has the same construction as that of a compound microscope, but the focal length of the
object lens is larger than the eye lens used in it. We are not going to draw the ray diagram of its
image formation in an astronomical telescope here rather will do it for the terrestrial telescope.
Terrestrial telescope
An astronomical telescope is not used to see objects on the earth's
surface. The demerit of an inverted final image in an astronomical
telescope led to the invention of the new telescope, in which the final
image is erect. This was achieved by adding one more lens between the
objective lens and eye lens in the model of the astronomical telescope.
The telescope which is used to observe distant objects on the earth's
surface is called a terrestrial telescope.
fig:terrestrial telescope
Construction: In a terrestrial telescope, there is an auxiliary lens, or erecting lens, in between
the objective lens and eye lens. A larger aperture of the object lens increases the quality of
image. So the aperture of the object lens in a terrestrial microscope is made larger. The eye lens
is smaller than the object lens and the auxiliary lens has the shortest focal length. Its main
purpose is to invert the image formed by the object lens.
The length of the telescope is adjusted in such a way that, L = fo + 4fa +fe. Where, fo is the focal
length of the object lens, fa the focal length of the auxiliary lens and fe the focal length of the
eye lens.
To infinity
fo
A1
2fa
O
Fo
Fe
B
A
B1
Auxiliary lens
(erecting lens)
2fa
fe
Eye piece
Objective
fig:ray diagram to show the formation of image in a terrestrial telescope
Working: The image, 'AB' of a distant object, is formed by the object lens at its focus (i.e., Fo).
The position of the auxiliary lens is so adjusted that 'AB' is at its center of curvature (2Fa). The
auxiliary lens forms a real image A1B1 of AB. A1B1 is inverted with respect to AB but erect with
respect to the object. Since the object is at the center of the curvature of the auxiliary lens, their
size is equal (i.e., size of A1B1= size of AB). Their distance from the center of the lens is 2fa. The
position of the eyepiece is so adjusted that the image A1B1 is on the focal plane of the eyepiece.
So the final image is formed at infinity. The final image is erect with respect to A1B1. Hence the
final image is erect with respect to the object.
Uses of a terrestrial telescope: A terrestrial telescope is a telescope used for viewing objects
on land. It is used for seeing armies from a greater distance, seeing signal flags on a distant
hill, etc.
0
88
Optional Science - 10
P HYS I CS
Drawbacks
1.
The length of the terrestrial telescope is longer than the astronomical telescope.
2.
Due to one extra lens added in this telescope, the intensity of the final image decreases.
Know the Reason
An astronomical telescope cannot be used to view distant objects on the earth's surface,
why?
In an astronomical telescope, the final image formed is inverted with respect to the object.
So an astronomical telescope cannot be used to view distant objects on the earth's surface.
Binoculars
Binoculars are a handheld optical instrument with two barrel chambers mounted on a single
frame side by side for providing a magnified view of distant objects. The two barrel chambers
in the binoculars are like two small
eyepiece
telescopes mounted together. When
we view through binoculars, a
perception of depth and 3-dimensional
structure is obtained on the basis of
visual information from the two eyes.
Light
precision
Two prisms are used in binoculars to
graphics
produce an erect final image by total
fig:construction and working of binoculars
internal reflection.
Construction
Modern binoculars consist of two barrel chambers. One is fixed with an objective lens and
the other with the eyepiece. There is a pair of prisms inside each barrel chamber. The prisms
reflect and lengthen the light, while the objective lenses enhance and magnify the images. The
tubes of the binoculars are made from aluminium and coated with silicon. Their lenses and
prisms are made from glass and coated with an anti-reflective coating.
Working
Binoculars are simply two telescopes placed side by side, one for each eye. The front lens
catches the light rays from a distant object and creates a focused image a short distance behind
the lens. This lens is called the objective. Binoculars have a pair of prisms inside them to rotate
the image 180 degrees. One prism rotates the image through 90 degrees, then the next prism
rotates it through another 90 degrees. The two prisms effectively turn the image upside down.
The final image of the object is obtained through the eyepiece. There is no loss of light energy
while propagating through the prisms due to total internal reflection. The two prisms used
in binoculars can lengthen the light path between the objective lens and the eyepiece (ocular
lens). Such an arrangement increases the magnification.
Uses of binoculars
Binoculars are a necessity for an astronomer, hunter, saltwater fisherman, boater, sports fan,
and experienced traveler. The following are some uses of binoculars:
P HYS I CS
Optional Science - 10
89
a.
General use: Binoculars of different categories like 3×10, 7×50, etc. are available in the
market. People use such binoculars to obtain a closer view for different purposes as in a
theater, while travelling, etc. Some binoculars are also equipped with night scope vision
to see objects that are far away even at night.
b.
Land surveys and geographic data collection: Geographers and other geoscientists use
binoculars for data collection.
c.
Bird watching: It is a popular hobby among nature and animal lovers. They use
binoculars of high magnification like 7×, 10×.
d.
Hunting: Hunters use binoculars to see animals which are difficult to spot with the
naked eye. They use binoculars of high magnification as well as of wider objective lens
to capture light in low light conditions.
e.
Military purposes: Binoculars have a long history of military use. One of the military
uses is to find the movements of the enemy in a specific territory. Military binoculars
are fitted with filters blocking LASER beams used as weapons.
f.
Astronomical use: Astronomers use binoculars for general observations in the sky. It
is used for locating astronomical objects in the night sky. Binoculars for astronomical
viewing have larger aperture objective lenses like 80 mm or larger. This increases the
total amount of light captured.
g.
To watch sport events live: To get a magnified and clear view while watching sports
like football on the ground, people use good quality binoculars.
Advantages of binocular vision
The following are some good features of binoculars vision:
a.
Binoculars are small and light in weight to carry.
b.
Seeing through a pair of binoculars with two eyes is suitable for observation of far
objects.
c.
Binoculars allow people to watch in three dimension.
d.
Binoculars are cheaper than a telescope.
Disadvantages of binocular vision
a.
Binoculars do not have wide visual field.
b.
The magnification of a pair of binoculars is less in comparison to a telescope.
Answer writing skill
1.
I
Name an optical instrument in which there is use of the phenomenon of total internal
reflection?
Prism binoculars.
2.
What is the relation between the power of a lens and its focal length?
The power of a lens is inversely proportional to its focal length. That is a lens with shorter
focal length has more power to converge or diverge the light rays falling on it.
0
90
Optional Science - 10
P HYS I CS
3.
Define magnification.
Magnification is the degree to which the object is enlarged during formation of its image
by using optical instruments like binoculars, a microscope, etc.
4.
How does a terrestrial telescope form an erect final image?
In a terrestrial telescope, there is use of an auxiliary lens in between the objective lens
and eye lens. It forms an inverted image. Finally there is formation of an erect image
when we observe through the eyepiece.
5.
Why is the power of a concave lens measured in the negative?
A concave lens has a virtual foci. Such a distance of the virtual focus is measured in
1
f
As the focal length of a concave lens is negative, its power measured is also negative.
negative. The power of a lens is reciprocal to its focal length, i.e., P =
6.
If a student wears lenses of power -4.5 D in his spectacles for correction of vision,
a.
What is the focal length of the corrective lens?
b.
What is the nature of the corrective lens?
a.
1
P
= —0.222 m
Focal length, f =
Or, f =
1
—4.5
Or, f = — 0.222 100 cm = —22.2
The focal length of the corrective lens is 22.2 cm.
b.
7.
The lens is a concave lens.
An astronomical telescope forms an inverted image but a terrestrial telescope forms
the final image erect. Present the mechanism behind it.
In an astronomical telescopethere are two lenses which form an inverted image of the
object at infinity. But terrestrial telescope forms the final image erect with respect to the
object due to a third lens between objective and eyepiece. The third lens of short focal
length f is placed at 2f which forms an inverted image of the object. This image serves as
the object for the eyepiece and final image becomes erect. The lens placed in the center
of the telescope which actually erects the image is called as the erecting lens.
8.
Explain the construction of a terrestrial telescope.
In a terrestrial telescope, there is an auxiliary lens, or erecting lens, in between the
objective lens and eye lens. The larger aperture of the objective lens increases the quality
of the image. So the aperture of the objective lens in a terrestrial microscope is made
larger. The eye lens is smaller than the objective lens, and the auxiliary lens has the
shortest focal length. Its main purpose is to invert the image formed by the objective
lens.
The length of the telescope is adjusted in such a way that, L = fo + 4fa +fe where, fo is the
focal length of the objective lens, fa is the focal length of the auxiliary lens and fe is the
focal length of the eye lens.
P HYS I CS
Optional Science - 10
0
91
Exercise
Step
1
Define
1. linear magnification
2. angular magnification 3. power of a lens
Very short answer questions
1.
What is a lens?
2.
Write the SI unit of the following
3.
a.
focal length
b.
power of a lens
Give the formula
a.
to calculate the magnification of a lens in terms of object distance and image distance.
4.
b. to calculate the power of combination of thin lenses.
What is an optical instrument?
5.
What is a compound microscope?
6.
What is a telescope?
7.
What is an astronomical telescope?
8.
What is a terrestrial telescope?
9.
What are binoculars?
Step
2
Short answer questions
1.
Write two uses each of the concave lens and convex lens.
2.
'The power of a lens gives the conversing and diverging capacity of a lens', justify this
statement.
92
Optional Science - 10
P HYS I CS
3.
Write some examples of magnification
4.
Write the meaning of the following:
a.
Power of a lens is 3D.
5.
b. Magnification of a lens is 7.
Write two uses of a compound microscope.
6.
Write two uses of a terrestrial telescope.
7.
Write two uses of binoculars.
9.
Write two advantages and two disadvantages of binocular vision.
12.
Distinguish between the nature of image formed by the eye lens and objective lens of
telescope.
Differentiate between
1.
Concave lens and convex lens
2.
Compound microscope and terrestrial telescope.
Give reasons
1.
Convex lens is called converging lens.
2.
Concave lens is called diverging lens.
3.
A convex lens has a real focus.
4.
It is dangerous to look through a convex lens at the sun or bright light.
5.
A concave lens has a virtual focus.
Step
3
Numerical problems
1.
An object is placed at a distance of 3 cm from a convex lens. It forms a real image at a
distance of 12 cm from the lens, then how many times does the lens magnify the size of
the object while forming its image? Ans: 4 times
2.
A convex lens magnifies the image of an objects 3 times the size of the object. If an object
is placed at a distance of 4 cm from the lens, then how far is the image formed from the
convex lens? Ans: 12cm
3.
Find the magnification of the lens which forms a real image of an object placed at a
distance of 4 cm in front of the lens on a screen 20 cm behind it.
Ans: 5
5.
An object of height 20 cm is placed at a distance of 2m from a convex lens. If a real image
of the candle is formed at a distance of 1m from the lens, then find the height of the image
formed. Ans: 0.1 m
6.
The height of object placed in front of a convex lens is 20 cm and that of the image formed
is 10 cm. Find the magnification of the lens. Ans: 0.5
P HYS I CS
Optional Science - 10
0
93
7.
A convex lens of power 10 D is used to burn a piece of paper by converging the solar
beam. What should be the distance between the lens and the paper to burn it? Ans:10 cm
8.
How far should a hand lens of power 20 D be placed from a book to read it clearly?
Ans: 5cm
9.
A lens has a power of –0.5 D. What are the focal length and the nature of the lens?
Ans:–2 m
10.
If a lens is of focal length 50 cm, then calculate its power.
Ans: +2.0 D
12.
A concave lens has a focal length of 20 cm. Calculate its power.
Ans: -5D
13.
A person having a myopic eye uses a concave lens of focal length 10 cm. What is the
power of the lens?
Ans: -10 D
14.
The power of a lens is + 5 D. Find its focal length in centimeters.
Ans: 20 cm
Draw a ray diagram
1.
to show image formation in a compound microscope.
2.
to show image formation in a terrestrial telescope.
4
Step
1.
Derive the formula to calculate the magnification of a lens involving object distance (u)
2.
v
u
Explain the construction and working of a compound microscope.
3.
Explain the construction and working of a terrestrial telescope.
4.
Explain the construction and working of binoculars.
5.
Explain individual eyepiece focus and center focus methods of binocular focusing.
and image distance (v) i.e. m =
Multiple choice questions [MCQs]
1.
If a lens is thicker at the center than at the edges, then it is
a. convex lens
b. concave lens
c.
plano concave lens
d. plano convex lens
2.
If a lens is thinner at the center than at the edges then it is
a. convex lens
b. concave lens
c. plano concave lens
d. plano convex lens
3.
4. A lens forms an image that is 5 cm tall when the object is 10 cm tall. The magnification
is
a. 0.2
b. 0.5
c.
4.
2
d. 5
The SI unit of power of a lens is
0
94
Optional Science - 10
P HYS I CS
5.
a.
dioptre/meter
b. meter
c.
meter-1
d. meter/dioptre
The length of a terrestrial telescope is given by
a. L = fa+ 4 fo +fe
b. L = fo + 4fa +fe
c.
d. L = 4fe + fa +fo
L = fo + 4fe +fa
Project Work
1.
Collect convex lenses of different thickness. Put those lenses in between two rectangular
blocks. Measure the gap between those two blocks to measure the thickness of lenses.
Let the sunlight refract through those lenses one after another. Converge the refracted
light on the ground. Move the lenses until you find a 'sweet spot' on the ground. As you
find such a sharp pointed image on the ground, measure the distance of the lenses from
the ground. This gives a rough estimate of the focal length of the lens. Fill your data in a
table as shown below:
S.N.
Type of lens
Focal length
Power
1.
IWhat Iis the relation between the thickness of the lenses and their focal length? Write
your conclusion.
2.
Make a telescope using a cardboard sheet, 2 lenses of
different thickness from magnifying glasses, black tape,
and a hot glue gun or super glue. Roll two cardboard
sheets to form two pipes in such a way that one pipe
can slide inside the other. Then tape the edges of the
cardboards. Glue the thicker lens on the outer edge of the
bigger pipe and thinner lens on the edge of the small pipe.
Your telescope is ready now. Hold the telescope with the inner tube facing your eye. Aim
it at an object in the night sky but not at the sun during day time, and adjust the distances
between the two lenses to obtain a sharp image.
P HYS I CS
Optional Science - 10
95
UNIT
6
CURRENT
ELECTRICITY
AND MAGNETISM
Michael Faraday (1791-1867) was an English scientist who contributed to the study
of electromagnetism and electrochemistry. His main discoveries include the principles
underlying electromagnetic induction, diamagnetism and electrolysis. Although Faraday
received little formal education, he was one of the most influential scientists in history.
Faraday established the basis for the concept of the electromagnetic field in physics. He
discovered the principles of electromagnetic induction and diamagnetism, and the laws
of electrolysis. His inventions of electromagnetic rotary devices formed the foundation
of electric motor technology, and it was largely due to his efforts that electricity became
practical for use in technology.
Key terms and terminologies of the unit
1.
Magnetization: The process of making a substance temporarily or permanently
magnetic by inserting it in a magnetic field is called magnetization.
2.
Diamagnetic substance: Substances which when placed in a strong magnetic
field acquire feeble magnetization opposite to the direction of the magnetic field
are called diamagnetic substance.
3.
Paramagnetic substance: Substances which when placed in a strong magnetic
field acquire feeble magnetization in the direction of the applied magnetic field
are called paramagnetic substances.
4.
Ferromagnetic substance: Substances which when placed in an external magnetic
field acquire strong magnetization in the direction of applied magnetic field are
called ferromagnetic substance.
5.
Magnetic flux: Magnetic flux is defined as the total number of magnetic lines of
force passing normally through any surface inside the magnetic field.
6.
Electromagnetic induction: The process of obtaining an induced emf in a closed
circuit by changing the magnetic flux linked with it is called electromagnetic
induction.
0
96
Optional Science - 10
P HYS I CS
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
24.
Fleming’s right hand rule: According to the Fleming’s right hand rule, “if we
stretch the right-hand thumb, fore finger and middle finger perpendicular to one
another and point the thumb in the direction of the motion of the conductor, the
fore finger in the direction of the magnetic field, then the middle finger indicates
the direction of the induced current from electromagnetic induction.”
Electric generator: An electric generator is a device that converts mechanical
energy into electric energy.
Alternating current (AC.): The current whose direction changes periodically and
whose magnitude also varies continuously is called an alternating current.
Direct current (DC): If the electrons always flow in the same direction and the
direction of a current remains unchanged in a conductor, it is called direct current
Motor effect: When a freely suspended current carrying conductor is kept in a
magnetic field, then it comes in motion. This effect is called motor effect.
Electric motor: An electric motor is the device which converts electric energy into
mechanical energy.
Mutual induction: This mechanism of obtaining an induced emf in a secondary
coil by passing an alternating current in the neighboring coil (primary coil) is
called mutual induction.
Transformer: A transformer is a device for increasing or decreasing AC voltage.
Step-up transformer: A transformer which converts the applied low voltage AC
to high voltage AC is called a step-up transformer.
Step-down transformer: A transformer which converts the applied high voltage
AC to low voltage AC is called a step-down transformer.
Resistor: A resistor is a two-terminal electrical component that adds electrical
resistance to the limit or regulates the flow of electrical current.
Series connection: When two or more resistors in a circuit are connected from
end to end in order to get the same current flowing through each of them in
succession, then the resistors are said to be connected in a series.
Parallel connection: When two or more resistors in a circuit are connected
between two common points in order to get different currents, then the resistors
are said to be connected in a parallel.
Diode: A diode is a two terminal electric component that allows electric current
to flow in only one direction.
Semiconductor: A semiconductor is a solid substance that has conductivity
between that of an insulator and most metals.
Intrinsic semiconductor: A semiconductor in its pure form is known as an
intrinsic semiconductor.
Doping: The process of adding impurity to pure semiconductors is called doping.
Extrinsic semiconductor: The doped semiconductors are called extrinsic
semiconductors.
P HYS I CS
Optional Science - 10
0
97
25.
26.
27.
28.
29.
N-type semiconductor: An extrinsic semiconductor which is created by doping
an intrinsic semiconductor with a pentavalent impurity like phosphorous (P), in
which electrons are the majority carriers and holes the minority carriers, is called
a N-type semiconductor.
P-type semiconductor: An extrinsic semiconductor, which is created by doping
an intrinsic semiconductor with trivalent impurity like boron (B), in which holes
are the majority carriers and electrons the minority carriers, is called a P-type
semiconductor.
P-N junction diode: A P-N junction diode is a two terminal device, whose one
side is made a P-type semiconductor and another side an N-type semiconductor
by doping on an intrinsic semiconductor.
Triode: Triode is a vacuum tube device with three elements - cathode, grid and
anode.
Transistor: A transistor is a three terminal semiconductor electronic device with
a P-type or N-type semiconductor region sandwiched in such a way that there is
formation of two P-N junctions.
Introduction
In today’s world, electricity is an important source of energy. It is a convenient form of energy
to convert into other forms of energy like heat, light, etc. Electricity is used in our homes
for lighting tubes and bulbs, operating fans, heating purposes, etc. All electric devices have
electric circuit at their heart. The electric loads are connected in series or parallel in an electric
circuit. Such loads convert electrical energy into other forms of energy. The way to connect
resistors in a series or parallel in an electric circuit and their features are described in this unit.
The magnetic property of a magnet is known as magnetism. Different types of substances
show variation in their behavior in an external magnetic field. Magnetic behavior of a material
depends upon its composition. In this unit, you will learn about magnetic property in matter.
Until the early 19th century, people treated electricity and magnetism independently. But
electricity and magnetism are interrelated. When a charged particle is in motion then there
is also a magnetic field around the particle. In 1820, Hans Christian Oersted discovered the
magnetic effect of current. Similarly, in 1831, Michael Faraday discovered electromagnetic
induction and the production of electricity from a magnetic field. This is a revolutionary
invention in the field of electricity generation. Transformers are used to increase the emf of
the electricity generated for its transmission. This unit also describes about electromagnetic
induction and principle of the generator, electric motor and transformer.
Magnetic property in matter
Spinning electrons in the atoms of matter have magnetic property. When a material is placed
in an external magnetic field, the magnetic forces of the material’s electrons will be affected.
Different types of materials can react quite differently to the presence of an external magnetic
field. This reaction depends on a number of factors, such as the atomic and molecular structure
of the material, and the net magnetic field associated with the atoms.
0
98
Optional Science - 10
P HYS I CS
Molecular theory of magnetism
The molecular theory of magnetism was given by Wilhelm Eduard Weber and modified by
James Alfred Ewing. According to the molecular theory of magnetism:
a.
Each molecule of a magnetic substance is an independent magnet.
b.
In a magnetized substance, all molecules are arranged in the form of an open chain so
that all north poles point towards one direction and all south poles towards the other.
In this way, one end becomes the north pole and the other end the south pole.
c.
In an unmagnetized substance, the molecular magnets are in the form of closed chains
and thereby cancel the magnetic fields of one another.
Magnetization
The magnetic behavior of a magnet is characterized by the alignment of the atoms inside a
substance. When an iron bar is brought under the application of a strong external magnetic
field, then the atoms inside the bar experience a turning effect, and they align in the direction
of the magnetic field applied. Iron gets strongly magnetized in the direction of the magnetic
field.
The process of making a substance temporarily or permanently magnetic by inserting in
a magnetic field is called magnetization. The response of a material to the application of a
magnetic field depends on the level of magnetization that the material undergoes.
Magnetic permeability
Magnetic permeability measures the degree of penetration of a magnetic field through the
substance kept in an external magnetic field. In other words, magnetic permeability measures
the capacity of the substance to accept magnetization.
Magnetic susceptibility
The measure of the extent to which a substance becomes magnetized when it is placed in an
external magnetic field is called magnetic susceptibility. It measures how easily or strongly a
material is magnetized by the applied external magnetic field.
Classification of magnetic substances
According to the behavior of the substance in the magnetic field, Pierre Curie and Michael
Faraday divided substances into three categories. They are diamagnetic substances,
paramagnetic substances and ferromagnetic substances.
Diamagnetic substances
Michael Faraday discovered that a specimen of bismuth was repelled by a strong magnet. He
coined the word diamagnetism for such properties of substances like bismuth. Substances
which when placed in a strong magnetic field acquire feeble magnetization opposite to the
direction of the magnetic field are called diamagnetic substance. For example, bismuth (Bi),
phosphorous (P), antimony (Sb), copper (Cu), zinc (Zn), silver (Ag), gold (Au), diamond,
graphite, water (H2O), common salt (NaCl), , hydrogen (H2), nitrogen (N2), etc.
Memory Plus
Two of the strongest diamagnetic materials are graphite and bismuth.
P HYS I CS
Optional Science - 10
0
99
Properties of diamagnetic substances
1.
Diamagnetic substance are somewhat repelled when brought near the ends of a
powerful magnet.
2.
When a rod of diamagnetic material is suspended
freely between two magnetic poles, it slowly turns
to set itself perpendicular to the direction of the
magnetic lines of force. The poles produced on
the two sides of the rod are similar to the nearer
magnetic pole.
3.
Suspended
S
N
S
diamagnetic substance
fig: diamagnetic substance in a magnetic field
In a non-uniform magnetic field, the diamagnetic substance is repelled towards the
weaker part of the field. That is, a diamagnetic substance moves from a stronger part to
a weaker part of the field.
For example, when a diamagnetic liquid taken in a watch glass
or glass crucible is placed over two nearby magnetic poles, then
the liquid accumulates on the sides causing a depression at the
center where the field is strongest as shown in the given figure.
When the distance between the pole pieces is increased, the
effect is reversed. That is the liquid rises in the middle, because
now the field is stronger near the poles.
fig:diamagnet liquid in a
magnetic field
4.
When a diamagnetic material is placed within a magnetic field, the lines of force tend
to go away from the material.
Paramagnetic substances:
Substances which when placed in a strong magnetic field acquire feeble magnetization in
the direction of the applied magnetic field are called paramagnetic substances. For example,
aluminium (Al), sodium (Na), platinum (Pt), chromium (Cr), manganese (Mn), cupric chloride
(CuCl2), oxygen (O2), etc.
Properties of paramagnetic substances
1.
These substances are attracted feebly towards the magnet when brought close to the
ends of a powerful magnet.
Know the Reason
Diamagnetic substances are repelled when brought near the ends of a powerful
magnet, why?
The electrons in a diamagnetic material rearrange their orbits slightly when kept
in a strong magnetic field. It induces a weak magnetic moment in the direction
opposite to the applied field. So diamagnetic substances are repelled when brought
near the ends of a powerful magnet.
Paramagnetic substances are attracted towards the magnet, why?
When paramagnetic substances are subjected to a magnetic field, these are feebly
magnetized in the direction of the field. So paramagnetic substances are attracted
towards the magnet.
100
Optional Science - 10
P HYS I CS
2.
3.
When a rod of paramagnetic material is
suspended freely between two magnetic poles,
then it slowly turns to set itself parallel to the
magnetic field. The poles developed at the end
of the rod are opposite to the nearer magnetic
poles.
Suspended
S
N
S
paramagnetic substance
fig: paramagnetic substance in a magnetic field
In a non-uniform magnetic field, the paramagnetic substance is attracted towards the
stronger part of the field. That is, the paramagnetic material moves from weaker to
stronger parts of the magnetic field.
For example, when a paramagnetic liquid taken in a watch glass
or glass crucible is placed over two nearby magnetic poles,
then the liquid rises in the middle where the field is strongest
as shown in the given figure. When the distance between the
pole pieces is increased, the effect is reversed. That is the liquid
depresses in the middle and rises near the edges, because now
the field is strongest near the poles.
4.
fig:paramagnet liquid in a
magnetic field
When a bar of paramagnetic material is placed in a magnetic field, the lines of force tend
to accumulate in it as shown in the given figure.
Ferromagnetic substances:
Substances which when placed in an external magnetic field acquire strong magnetization in
the direction of the applied magnetic field are called ferromagnetic substance. For example,
iron (Fe), cobalt (Co), nickel (Ni), magnetite (Fe3O4), gadolinium (Gd), dysprosium (Dy) and
their alloys.
Properties of ferromagnetic substances
Ferromagnetic substances show properties of a paramagnetic substance to a much greater
degree. The following are the properties of ferromagnetic substances:
1.
These substances when placed in a magnetic field, are strongly magnetized in the
direction of the field. So they are even attracted by a weak magnet.
2.
When a rod of paramagnetic material is suspended freely between two magnetic poles,
then it rotates and finally sets itself parallel to the magnetic field.
3.
In a non-uniform magnetic field, the ferromagnetic substance is attracted towards the
stronger part of the field.
4.
The magnetic lines of force tend to crowd into the ferromagnetic substance.
Magnetic flux
In class 9 optional science, you had drawn magnetic lines of force around a bar magnet.
Magnetic lines of force are imaginary curved lines which enter into the south pole from the
north pole of a magnet. Such lines of force never intersect each other. The tangent at any
point on the magnetic lines of force gives the direction of the magnetic field at that point. The
magnetic lines of force are around magnets as well as a current carrying coil. Shape of the
magnetic lines varies according to the source of magnetic field. The shape of the magnetic
lines of force gives us an idea about the magnetic field around a source.
P HYS I CS
Optional Science - 10
101
~ !Iij ;-•1:• j) (?tr·n
Current
in wire
wire
Solenoid
The Earth
Bar Magnet
fig:magnetic field sources
fig:magnetic flux
A surface inside a magnetic field receives magnetic lines of force. We look after the number
of magnetic lines of force falling over a surface to know the effect of the magnetic field. The
term used in physics to measure the magnetic field strength over a given area is magnetic
flux. Therefore, magnetic flux is defined as the total number of magnetic lines of force passing
normally through any surface inside the magnetic field. Magnetic flux is denoted by Φ. The
magnetic flux through area ‘A’ at right angles to the magnetic lines of force is given by
Φ = BA
Where ‘B’ is the magnetic field strength normal to the surface area ‘A’.
a.
SI unit of magnetic flux: The SI unit of magnetic flux is the weber. Its symbol is Wb.
The unit weber is given after the German physicist and co-inventor of the telegraph,
Wilhelm Weber.
b.
Variation of magnetic flux: The magnetic flux is proportional to the number of field lines
that pass through a surface. If a magnet, or a coil, is moved closer to one another, then
the magnetic flux through the surface of the coil increases. Conversely, the magnetic
flux decreases when it is moved away from one another.
Electromagnetic induction
A magnetic field exists in the region around a current
~
! Magee< mosiagdowa
I Magae, mo,iag ,p
carrying conductor, such as a wire. Moving a conductor
in a magnetic field is the basis for a simple electric
generator. When a conductor is moved in a magnetic
I
,
CoU
, )
CoU
field in such a way that it intersects the magnetic lines of Cfo,,,aaome,e,
al,aaome<"
force perpendicularly, then the magnetic flux linked with
the circuit gets changed. This change in magnetic flux fig: electromagnetic Induction through a coil
causes an electric current to flow through the conductor. Such effect is called electromagnetic
induction. The process of obtaining an induced emf in a closed circuit by changing the
magnetic flux linked with it is called electromagnetic induction.
ij
L__§
g
~
g
Memory Plus
If there is a relative motion between a magnet and a coil, an emf is induced in the coil.
Activity- 6.
1.
Make a coil by winding about 50 turns of thin insulated copper
wire round a cylindrical object.
2.
Connect the two terminals of the coil with a galvanometer.
102
Optional Science - 10
P HYS I CS
3.
Move a pole of a bar magnet in and out of the coil and observe the deflection of the
needle in the galvanometer.
4.
Investigate how the magnitude of the induced current depends on (i) the speed of the
relative motion, (ii) the strength of the magnet,(iii) the number of turns on the coil
The given experiment shows that
1.
When a magnet is moved quickly into a coil a large current gets induced.
2.
When a powerful magnet is used, the magnitude of the induced current increases. This
is because a more powerful magnet has more lines of force between its poles. So when
a wire moves through the field, it cuts the magnetic lines of force more often.
3.
When the number of turns in a coil increases, the induced emf also increases.
4.
In the above activity, if the magnet is moved away from the coil with the south pole
pointing towards the coil, then it produces deflection in the opposite direction as
compared to the case when the magnet is moved towards the coil.
Faraday’s laws of electromagnetic induction
Electromagnetic induction was discovered in 1831
by Michael Faraday. He was the first to observe
how the magnitude of an induced emf depends
upon the rate of change of magnetic flux. On the
basis of the observations made in his experiment,
Faraday formulated the following laws.
a.
Whenever the magnetic flux linking a coil
changes, then an emf is induced in the coil.
fig: electromagnetic induction
b.
The magnitude of the induced emf is directly proportional to the rate of change of the
magnetic flux.
c.
The induced emf lasts as long as there is a relative motion between the magnet and the
coil.
Faraday observed the deflection of the galvanometer needle in the opposite direction when
the direction of the motion of the conductor was changed. This is due to the change in the
direction of the induced current while changing the direction of motion of the conductor in
between the two magnetic poles. The direction of the induced current in electromagnetic
induction is given by Fleming’s right hand rule.
Know the Reason
A stationary magnet does not induce a current in a coil, why?
In the case of a stationary magnet, the magnetic flux linked with a closed circuit or a coil
remains constant. When it is moved to and fro, the magnetic flux linked with the closed
circuit changes and an emf. gets induced. So a stationary magnet does not induce a current
in a coil.
P HYS I CS
Optional Science - 10
103
Fleming’s right hand rule
Fleming’s right hand rule is used to predict the direction of
an induced current in electromagnetic induction. According
to Fleming’s right hand rule, if we stretch the right-hand
thumb, fore finger and middle finger perpendicular to one
another and point the thumb in the direction of the motion of
the conductor, the fore finger in the direction of the magnetic
field, then the middle finger indicates the direction of the
induced current from electromagnetic induction.
e;,,aJ
Induced current
fig:Flemings right hand rule
Applications of electromagnetic induction
Many electrical devices operate on the principle of electromagnetic induction. The bicycle
dynamo and generator are the most important devices based on electromagnetic induction.
Bicycle dynamo
Activity:
Take a bicycle with dynamo lights.
Push the driving wheel of your
bicycle dynamo towards the tyre.
Lift the wheel of your bicycle and
make sure that it rotates freely.
Observe the brightness of the light
when the wheel is rotating slowly.
Now rotate the wheel faster to
observe the brightness of the bulb
in this case, too.
.....-rotating
--
ridged knob
magnet
~iron core
copper
coil
to light
connection to
bicycle frame
fig:bicycle dynamo
1.
What changes do you observe in each case?
2.
Does the induced current last for a long time in the wire?
The brightness of the dynamo light increases with the increasing speed of the bicycle
wheel. It is due to the increased rate of change of the magnetic flux. Such induced
current in the wire lasts as long as the bicycle wheel rotates.
Dynamos convert mechanical energy into electrical energy. A bicycle dynamo is a very simple
dynamo in which a magnet is made to spin around near a fixed coil.
i.
Principle of a bicycle dynamo:The working principle of a bicycle dynamo is based on
electromagnetic induction, i.e., whenever the magnetic flux linked with a closed circuit
changes, an electromotive force, or emf, gets induced in the circuit. As a result, electrical
current is obtained from the two terminals of the coil used in the bicycle dynamo.
ii.
Construction: A bicycle dynamo has a cylindrical permanent magnet with poles on
opposite sides of the cylinder, which is fixed on an axle attached to the driving wheel.
Its coil is fixed on the iron core. Both the coil and magnet are sealed in a metal case.
iii.
Working mechanism: When the driving wheel of a dynamo rubs against the tyre, it
rotates the cylindrical magnet inside the bicycle dynamo. Due to this, the magnetic flux
linked with the coil changes and an emf gets induced in the coil.
104
Optional Science - 10
P HYS I CS
Generator
An electric generator is a device that converts mechanical energy into electric energy. It is used
to generate electricity on a large scale. In a generator, an armature is rotated in a magnetic field
at a high speed to generate electric current on a large scale.
Principle of generators
The working principle of generators is based on electromagnetic induction, i.e., whenever
the magnetic flux linked with a closed circuit changes, an emf gets induced in the circuit. As
a result, electrical current is obtained from the two terminals of the coil used in a generator
Types of generators: AC and DC generators are the two types of generator.
AC generator
An alternating current generator is called an AC generator. In alternating current, the
electrons flow forward and backward. The current whose direction changes periodically and
whose magnitude also varies continuously is called an alternating current. An AC generator,
bicycle dynamo, etc. are sources of AC. In an AC generator, the ends of the coil windings are
connected to two slip rings. Turning the coil at a steady speed produces an alternating current
(AC), which changes its polarity periodically, and the magnitude remains variable.
Construction of an AC generator
Penna,~ent
magnet
Rectang ular
coil
fig:construction of a.c. generator
An AC generator is consists of four main parts:
a.
Coil or armature: In an AC generator, there is a rectangular coil ABCD with a large
number of turns of insulated copper wire over a soft iron core. It is also called an
armature. The soft iron core used in the armature increases the magnetic flux.
b.
Magnetic field: It is usually the field developed by a strong horse shoe type magnet
having concave poles. The coil can be rotated rapidly in between the north pole (N) and
south pole (S) of the strong magnet with the help of a shaft. The axis of the armature is
perpendicular to the magnetic field lines.
P HYS I CS
Optional Science - 10
105
c.
Slip rings (R1 and R2): The slip rings used are two circular pieces of copper. The two
ends of the copper wire in the coil are connected to slip rings R1 and R2. These rings
rotate with the coil to draw current from the generator.
d.
Carbon brushes (B1 and B2): Slip rings are tightly kept in contact with two carbon
brushes B1 and B2. Each slip ring rubs against a brush. This type of contact makes good
electrical contact to conduct electricity when the two slip rings R1 and R2 are rotated
with the coil.
Working of an AC generator
As the coil rotates in a magnetic field, an alternating emf is induced across its two ends. This
causes a flow of alternating current in the coil. The current produced in the rotating coil can be
tapped out through the slip rings into the carbon brushes. From the carbon brushes, current is
taken out through the wires.
From the given figure showing the construction of an AC generator, when the coil ABCD is
rotated in a clockwise direction between the north pole (N) and the south pole (S) of a strong
magnet, the arm AB of the coil moves up, cutting the magnetic lines of force near the N-pole
of the magnet. On the other side, the arm CD of the coil moves down, cutting the magnetic
lines of force near the S-pole of the magnet. According to Fleming’s right hand rule, the
induced currents are in the directions A to B on the arm AB and C to D on the arm CD. Thus,
the induced current on the two sides of the coil are in the same direction, and we get an
effective induced current in the direction ABCD.
+ve maximum value
+I
Current (I)
In each cycle of an alternating current, the current changes
its direction twice. When we say the frequency of an AC is 50
Hz, it means the current changes its direction 100 times in one
second. The alternating current supplied in our country has a
frequency of 50 Hz.
Alternating
time (t)
—I
—ve maximum value
fig:current-time graph for a.c.
DC generator
A direct current generator is called a DC generator. If the electrons always flow in the same
direction and the direction of a current remains unchanged in a conductor, it is called a direct
current. A cell has fixed positive and negative electrodes. The current flowing from a cell is
DC. A dry cell, photo cell, solar panel are sources of DC.
Rectangular
coil
Construction of a DC generator
a.
Optional Science - 10
rre
nt
cu
Field
nt
rre
N
Coil or armature: In a DC generator,
there is a rectangular coil ABCD with
a large number of turns of insulated
copper wire over a soft iron core.
106
C
B
Permanent
magnet
field
cu
As in an AC generator, a DC generator
also consists of four main parts. If we
replace the slip rings of an AC generator
by a commutator, then it will become a DC
generator.
M
Rotation of coil
anticlockwise
A
motion
R1
+B1
R2
—B2
D
S
Commutator
Carbon brush
G
Galvanometer
fig:construction of d.c. generator
P HYS I CS
b.
Magnetic field: It is usually the field developed by a strong horse shoe type magnet
having concave poles. The coil can be rotated rapidly in between the north pole (N) and
south pole (S) of the strong magnet with the help of a shaft.
c.
Half ring or split rings (R1 and R2): The split rings used are two semi-circular pieces of
copper. The two ends of the coil are connected to the two copper half rings or split rings
R1 and R2 of a commutator.
d.
Carbon brushes (B1 and B2): Split rings are tightly kept in contact with two carbon
brushes B1 and B2. Each split ring rubs against a brush. This type of contact makes good
electrical contact in conducting electricity when the two split rings R1 and R2 are rotated
with the coil. The two half rings R1 and R2 touch the two carbon brushes B1 and B2 one
by one.
Working of a DC generator
The current produced in the rotating coil can be tapped out through the commutator half rings
into the carbon brushes. From the carbon brushes, current is taken out through wires.
From the given figure showing the construction of an AC generator, when the coil ABCD is
being rotated in an anticlockwise direction between the north pole (N) and south pole (S) of a
strong magnet, the arm AB of the coil moves down, cutting the magnetic lines of force near the
N-pole of the magnet. On the other side, the arm CD of the coil moves up, cutting the magnetic
lines of force near the S-pole of the magnet. According to Fleming’s right hand rule, the
induced currents are in the directions B to A on arm AB and D to C on arm CD. Thus, the
induced current on the two sides of the coil are in the same direction, and an effective induced
current in the direction DCBA. Direct current is obtained from the two terminals of the carbon
brushes as
i.
One carbon brush (B1) is at all times in contact with the
coil arm moving down in the magnetic field. Due to this,
the brush B1 becomes a positive (+) pole of the generator.
ii.
Another carbon brush (B2) always remains in contact
with the coil arm moving up in the magnetic field. Due
to this, the brush B2 becomes the negative (-) pole of the
generator.
C
~
Time ~
:,
u
fig:current-time graph for d.c.
Due to this, the current in the outer circuit always flows in one direction. So, it is direct current.
Methods to increase the induced emf from a dynamo and generator
a.
By increasing the number of turns in the coil.
b.
By decreasing the distance between the coil and magnet.
c.
By using a powerful magnet. It increases the strength of the magnetic field.
d.
By increasing the rate of change of the magnetic flux. This can be done by rotating the
coil or magnet faster.
P HYS I CS
Optional Science - 10
0
107
Motor effect
In 1820, Hans Christian Oersted discovered that electric currents cause magnetic fields around
them, which is the magnetic effect of an electric current. The given figure shows an electric
field around a straight current carrying current. It is a circular field.
When a wire carries an electric current through another
magnetic field, then the two magnetic fields interact. There
is mutual attraction or repulsion due to the magnetic
field developed between a current carrying conductor
and magnetic field of the magnet. French scientist Andre
Marie Ampere in 1820 demonstrated this force. The forces
between the two magnetic fields can move wires or turn
the coil which carry an electric current. Thus, when a
freely suspended current carrying conductor is kept in a
magnetic field then it comes in motion. This effect is called
motor effect.
~
magnetic
fields in
~ t h e same
direction
repel
~agnetic fields
I~ the opposite
direction attract.,.;:-r
wire pushed
in this
direction
current
direction
wire
fig:motor effect
Activity- 6.
1.
Take a conductor and a conducting wire.
2.
Make a support of the conducing wire at two points ‘A’ and
‘B’.
3.
Hang the conductor from a stand as shown in the given figure
and connect the two terminals of the conductor to a battery.
4.
Bring a U-shaped magnet close to the conductor. Do you
observe movement in the conductor?
S
A
B
N
The movement in the conductor is due to the motor effect.
Electric motor:
An electric motor represents the transformation of energy from one form to another. An
electric motor is a device which converts electric energy into mechanical energy. It is an
application of motor effect. In an electric motor, electricity passes through a coil of wire,
producing a magnetic field around it.
computer fan
electric mixture
fan
immersion motor
water lifting pump
washing machine
Principle of electric motor
It is based on the principle of motor effect, i.e., when a rectangular coil is placed in a magnetic
field and current is passed through it, a turning effect acts on the coil, which rotates it
continuously to convert electrical energy into mechanical energy.
108
Optional Science - 10
P HYS I CS
Types of electric motor
DC motor
A DC motor is a common type of motor that is powered by direct current. For example, the
motor of battery- operated toys, motors in electronic devices like DVD players, computers,
Construction: A DC motor consists of the following parts:
i.
Armature: A DC motor consists of a coil with a large number of turns of insulated
copper wire over a soft iron core. This coil wound on the soft iron core forms the
armature. The coil is mounted on an axle and is placed between the cylindrical concave
poles of a magnet.
ii.
Magnetic field: A permanent magnetic field is around the armature.
iii.
Half ring or split rings (R1 and R2): The split
rings used are two semi-circular pieces of copper.
The two ends of the coil are soldered to the two
copper half rings or split rings R1 and R2 of a
commutator. It is used to reverse the direction of
flow of current. They rotate along with the coil.
iv.
Brushes: Two carbon brushes (B1 and B2) in contact
with the commutator make a tight connection to
conduct electricity. A battery is connected to the
brushes which are in contact with the rings.
Working of DC motor
Termlnals
fig: construction of d.c. motor
Thrust
When the coil is powered, a magnetic field is generated around
the armature. According to the Fleming’s left hand rule, the
left side of the armature is pushed away from the N-pole of the
Fhced carbon
brushes
magnet and drawn towards the right, causing rotation. When
0
the coil turns 90 , the brushes lose contact with the commutator,
and the current stops flowing through the coil. However the
coil keeps turning because of its inertia of motion.
fig:working of a d.c. motor
Now when the coil turns 1800, the sides get interchanged. That
is, the left side of the armature is now at the right side. As a result, the split ring R1 is now
in contact with brush B2 and split ring R2 is in contact with brush B1. Therefore, the current
continues to flow in the same direction. This ensures that the turning effect on each coil is
always in the same direction.
AC motor
An AC motor is powered by alternating current. For example,
the motor in a driller machine, vacuum cleaner, water lift
pump, etc. Though the working principle of the AC motor is
the same as that of a DC motor, there are some differences in
their construction and working mechanism. The polarity of
fig: a.c. motor
AC changes periodically and its magnitude varies. Thus, the
magnetic field produced by the electromagnets also changes its direction at the same time.
This dual switching at the same time causes the direction of turning force on the coil to remain
the same.
P HYS I CS
Optional Science - 10
109
Memory Plus
An AC motor runs at a fixed speed that is determined by the frequency of AC supply. On
the other hand, DC motor has speed-control capability.
Differences between DC and AC motors
DC motor
AC motor
The field magnet is a permanent magnet.
The field magnet is an electromagnet.
Split rings or commutators are used.
Slip rings are used.
They are powered by a direct current.
They are powered by an alternating current.
Applications of electric motor
Electric motors are used in many ways in our daily lives.
i.
Electric fan rotates due to the motor in it.
ii.
Electronic devices like computers, DVD players have motors in them.
iii.
Water lifting pump consists of a motor.
iv.
Saw mills, rice mills have powerful motors.
Comparison of DC generator with DC motor
The construction of a DC generator is the same as that of a DC motor. But their working
mechanism is just the opposite to one another. In a DC generator, we rotate the coil and
produce direct current whereas in a DC motor, we do apply direct current and rotate the coil.
If a DC generator is connected to a battery, it will work as a motor. Conversely, if a motor coil
is made to rotate, then it will work as a DC generator and produce direct current at the brushes.
Memory Plus
The DC generator, or DC dynamo, consists of two half rings. If the half rings are replaced
by slip rings then they will change correspondingly into AC generator and AC motor.
Differences between electric motor and electric generator
Electric motor
Electric generator
1.
It converts electric current into 1. It converts mechanical energy into electric
mechanical energy.
current.
2. Current is supplied to the coil placed in 2. The coil is rotated in the magnetic field by an
a magnetic field by an external source.
external source.
3. It is based on the motor effect.
3. It is based on the principle of electromagnetic
induction.
Transformer
Electromagnetic induction can be used to transfer electrical energy from one circuit to another
by means of a magnetic field which links the two coils. The two coils are called primary coil
and secondary coil.
110
Optional Science - 10
P HYS I CS
An induced emf appears in the secondary coil when there is a change of current in the primary
coil. There are two ways of changing the current in the primary coil.
1.
Direct current (DC) in the primary coil can be switched on and off rapidly by an
automatic mechanism.
2.
An alternating current (AC) can be used in the primary coil. Its magnitude and direction
change periodically. This mechanism of obtaining an induced emf in a secondary coil
by passing an alternating current in the neighboring coil (primary coil) is called mutual
induction. A transformer is based on the principle of mutual induction.
The transmission of electricity involves transferring energy over a long distance. In a
hydropower station or nuclear power plant, electricity is first generated at a lower potential
difference. It must be stepped up to a high voltage like 12,000 V for its transmission. When
electricity enters a building or home, the high voltage alternating current (AC) should be
stepped down to a low voltage like 220 V. A transformer is a device for increasing or decreasing
an AC voltage. Transformers are essential in the transmission of electricity from a power
station to the customers.
a.
Primary coil: It is the coil connected to the
alternating current source. The number of
windings in the primary coil are called
primary turns (n1) and the AC voltage
supplied in the primary coil is called
primary voltage (V1).
n2
n1
ad
A transformer has two coils fixed to a soft-iron
core. The main part of a transformer are,
laminated soft-iron core
Applied
a.c. supply
Lo
Construction
secondary voltage (V2)
primary voltage(V1)
secondary turns (n2)
primary turns (n1)
fig:construction of a transformer
b.
Secondary coil: It is the coil through which the stepped-up or stepped-down AC voltage
is obtained. The number of windings in the secondary coil are called secondary turns
(n2) and the AC voltage supplied in the secondary coil is called secondary voltage (V2).
c.
A soft iron laminated core: A block
made from U-shaped iron strips or E and
I shaped iron strips to fix the primary
coil and secondary coil of a transformer
is called the core. The process of joining
polished U-shaped iron strips together is
called lamination of the core. Shellac and
varnish are used to polish the iron strips.
Solid
Core
fig:with no lamination
high eddy current
fig:lamination of core
of a transformer
Know the Reason
The core of a transformer is laminated so that layers of soft iron are separated from
one another by layers of insulating material. Due to lamination of the core, induced
currents (i.e., eddy currents) in the core are reduced. It causes the flux from the
primary coil as high as possible.
P HYS I CS
Optional Science - 10
111
Working principle of a transformer
A transformer is based on the principle of mutual induction. In a transformer, an alternating
current passes through the primary coil when it is connected to an AC source. The magnetic
field due to AC in the primary coil changes in both magnitude and direction. This changing
magnetic field changes the magnetic flux linked with the secondary coil. The core provides
magnetic path for the flux, to get linked with the secondary winding. According to Faraday’s
laws of electromagnetic induction, whenever the magnetic flux linked with a closed circuit
changes, an emf gets induced from two terminals of the secondary coil. Transformers are
designed so that all the magnetic flux produced by the primary coil passes through the
secondary coil.
A transformer is based on the following two laws:
i.
According to the law of conservation of energy, the power input in the primary coil (P1=
I1V1) is equal to the power output in the secondary coil (P2 = I2V2).
ii.
The magnitude of induced emf is directly proportional to the ratio of number of turns
in the secondary coil (n2) to the number turns in the primary coil (n1).
Know the Reason
A transformer does not work with DC, why?
Instead of AC, if DC is supplied in the primary coil then the magnetic field produced is of
constant strength. Due to this, the number of magnetic lines of force which are intersected
by the secondary coil does not change. In such a condition, current does not get induced
from the two terminals of the secondary coil. So a transformer does not work with DC.
Energy losses in a transformer
An ideal transformer is a theoretical and linear transformer. It is lossless and perfectly coupled;
i.e, there are no energy losses and flux is completely confined within the magnetic core. In case
of a real transformer, there are following possible energy losses.
a.
Eddy current losses: In a transformer, the alternating current (AC) in the primary coil
b.
Copper losses: Generally the primary coil and secondary coil of a transformer are
c.
Flux losses: In a transformer, the magnetic flux linked with the primary coil is not
equal to the magnetic flux linked with the secondary coil. Most of the flux gets linked
with the secondary winding which is called as ‘useful flux’ or main ‘flux’, and the flux
which does not get linked with secondary winding is called as ‘leakage flux’.
produces a changing magnetic field. Due to this changing magnetic field, eddy currents
are induced in the soft-iron core of the transformer. These currents could cause the core
to become very hot. The possible loss of energy can be reduced by the design of the
transformer. For this, the core is made of thin sheets of iron called lamination, separated
by insulating material. This makes it much harder for the eddy currents to flow.
made of copper wire. They have resistance. When current flows through these wires, a
part of the energy is lost in the form of heat. This energy lost through the windings of
the transformer is known as copper loss. The use of thick wires for windings can reduce
copper loss.
112
Optional Science - 10
P HYS I CS
d.
Losses due to vibration of core: A transformer in operation produces a humming
noise. Some of the electrical energy supplied is wasted in the form of mechanical energy
during vibration of the core, which produces sound.
Transformer formula
The transformer formula relates primary voltage (V1), primary turns (n1), secondary voltage
(V2) and secondary turns (n2) in a transformer as:
Secondary voltage (V2) Secondary turns (n2)
=
Primary voltage (V1)
Primary turns (n1)
This formula is used to count the number of turns in the primary coil and secondary coils
while manufacturing a transformer.
Solved numerical- 6.
In a transformer, the ratio of secondary turns to primary turns is 4:3. Which type of transformer
is it? Find the secondary voltage when the transformer is connected to a power supply of 220 V.
Solution:
Here, the ratio of secondary turns to primary turns (n2:n1) = 4:3
This type of transformer has more turns in the secondary coil. So it is a step-up
transformer.
Primary voltage (V1) = 220 V
Secondary voltage (V2) = ?
According to the transformer formula
Secondary voltage (V2) Secondary turns (n2)
=
Primary voltage (V1)
Primary turns (n1)
V2 4
=
Or
220 3
4 × 220
= 293.33 V
Or
V2 =
3
Therefore, the secondary voltage is 293.33 V.
Solved numericalA step-up transformer has 10,000 turns on its secondary coil and 100 turns on its primary
coil. An alternating current of 5 A flows in the primary coil when it is connected to a 12 V AC
supply. Calculate
1.
The power input to the transformer
2.
The emf induced across the secondary coil.
Solution
Here, Primary voltage (V1) = 12 V
Secondary voltage (V2) = ?
Primary current (I1 ) = 5 A
Secondary turns (n2) = 10,000
Primary turns (n1) = 100
P HYS I CS
Optional Science - 10
0
113
Now, (i) Input power = I1V1 = 5 × 12 = 60 W
(ii) Secondary voltage is given by the formula
Secondary voltage (V2) Secondary turns (n2)
=
Primary voltage (V1)
Primary turns (n1)
V1 × n2 12× 10000
= 1200 V
=
n1
100
Therefore, the emf induced across the secondary coil is 1200V.
Or,
V2 =
Types of transformers
There are different types of transformers on the basis of number of windings, construction, their
purpose, types of supply, their use, coolant material used, etc.
a.
On the basis of construction : Core type transformer and shell type transformer
b.
On the basis of their purpose: Step up transformer and tep down transformer
c.
On the basis of type of supply: Single phase transformer and three phase transformer
d.
On the basis of their use: Power transformer, distribution transformer and instrument
transformer
e.
On the basis of cooling employed: Oil-filled self cooled type; oil-filled water cooled type
and air blast type (air cooled)
Here, in class 10 optional science, you will learn about the types of transformers on the basis of
number of windings. Step-up transformer and step-down transformers are the two types of
transformers on the basis of windings.
Step-up transformer: High potential difference is required for
transmission of electricity from a hydropower station over long
distances. The transformer which converts the applied low voltage
AC to high voltage AC is called a step-up transformer. It is designed
with more numbers of secondary turns than primary turns, i.e., n2
> n1. So the secondary voltage is stepped up compared with the
potential difference applied to the primary coil.
Laminated Iron Core
fig:step up transformer
Applications
i.
It is used to obtain high voltage of about 15000 V to accelerate the electron beam in a
Cathode Ray Tube (CRT) from 220 V.
ii.
In a hydropower station or nuclear power plants, the low voltage AC is stepped up to a
high voltage like 12 kV (12,000 V) by using a step-up transformer for its transmission.
iii.
In a microwave oven, a step-up transformer changes the input voltage of about 120V-240V
to around 5000V.
iv.
An inverter transformer converts low voltage from the battery to 220-240V AC.
Step-down transformer: We need a device to run a 3V radio from
L~~~
a 220V AC. Such a device lowers the AC voltage to the desired level.
The transformer which converts the applied high voltage AC to low
Pri~
voltage AC is called a step-down transformer. It is designed with
fig:Step down transformer
less numbers of secondary turns than primary turns, i.e., n2 < n1. So
the secondary voltage is stepped down compared with the potential difference applied to the
primary coil.
0
114
Optional Science - 10
P HYS I CS
Applications:
i.
In a distribution substation, a step down transformer is used to lower the high voltage AC
from the power station to 220V for domestic use.
ii.
Battery chargers like a cell phone charger has a step-down transformer, which reduces 220
V to between 3 V and 9V.
Differences between step-up transformer and step-down transformer
Step-up transformer
Step-down transformer
The windings in the secondary coil are The windings in the secondary coil are less
more than those in the primary coil.
than those in the primary coil.
It converts low voltage AC at high current It converts high voltage AC at low current into
into high voltage AC at low current.
low voltage AC at high current.
Resistor
A resistor is a two-terminal electrical component that adds electrical resistance to limit or
regulate the flow of electrical current. In electronic circuits, resistors are used to reduce current
flow, adjust signal levels, to divide voltages, etc. The value of the resistances used in electrical
and electronic circuits varies over a wide range.
Connection of resistors/ electrical devices
You may have seen that a number of resistors connected together in a specific way on the
board of electronic devices. Also in our domestic circuit, there are a number of electric loads
like bulbs, a TV, fan, refrigerator, electric motor, etc. Such loads also offer resistance to the flow
of electrons. They are connected to the same main power supply to our home. There are two
ways to connect two or more resistors or electrical devices together in a circuit. They are series
connection and parallel connection.
Series connection
In a series circuit, two or more appliances are connected so as to provide a single conducting
path for current. Thus, the same current flows through all of the resistors in the connection.
When two or more resistors in a circuit are connected from end to end in order to get the same
current flowing through each of them in succession, then the resistors are said to be connected
in series connection. For example, the decorative lights used to illuminate during Dipawali,
Christmas, etc.
Expression of the equivalent resistance in a series connection of resistors
In the given circuit diagram, three resistors of resistance R1, R2 and R3 are connected in series
with a source of potential difference ‘V’. Let a current ‘I’ flow through the circuit.
From Ohm’s law, the potential differences across the three resistances is given by
V1 = IR1, V2 = IR2, V3 = IR3
If R be the equivalent resistance of the series connection, then on applying a voltage ‘V’ across
it, the same current ‘I’ must flow through it.
-v---So,
V = IR
But
V = V 1 + V2 + V3
Or
∴
-+---V I_. -+--V 2____..._y 3----+
-~---R,
IR = IR1 + IR2 + IR3
R = R1 + R2 + R3
Rz
fig:series connection of resistors
P HYS I CS
Optional Science - 10
115
Characteristics of series connection of resistors
The following are some important characteristics of series connection of resistors:
1.
There is a single conducting path for all the resistors in a series circuit.
2.
The potential difference across individual resistors is not the same. The net potential
difference between the two ends of the combination is equal to the sum of the potential
difference between the individual resistors. i.e.,
V = V1 +V2 +V3
3.
The current through the different resistors is the same.
4.
The total resistance in a series circuit is equal to the sum of separate resistances in the
circuit. i.e.,
R = R1 +R2 +R3.
Disadvantages of series connections
In a series circuit, resistors or electric loads are connected one after another. So
1.
A separate switch cannot be used for individual resistors. It is not possible to operate
the resistors independently.
2.
If just one resistor stops working due to some defect, then all other resistors in the
circuit fail to function.
3.
Each resistor does not get the same voltage.
4.
The overall resistance of the resistors gets increased. Due to this, the current from the
power supply is low.
Parallel circuit
In a parallel circuit, two or more appliances are directly connected to a source of electricity.
Each resistor has an individual path for the flow of current. Thus, electric current divides
in a parallel connection of resistors. When two or more resistors in a circuit are connected
between two common points in order to get different currents, then the resistors are said to be
connected in parallel connection.
Expression of equivalent resistance in a parallel connection of resistors
In the given figure, three resistances R1, R2 and R3 are connected
in parallel with a source of potential difference ‘V’. Let a current
‘I’ flows through the circuit. The current ‘I’ at point ‘A’ is divided
into three currents as I1 along R1, I2 along R2 and I3 along R3.
Now, from Ohm’s law, the individual current through each
resistor is given by
V
V
V
V
I1= ,
I2= ,
I3=
(since, I= )
R1
R2
R3
R
These three currents recombine at point ‘B’ to give the same
current ‘I’. i.e., I = I1 + I2 + I3
If R be the equivalent resistance of the parallel connection, then
V V V V
= +
+
R R1 R2 R3
∴
116
1
1
1 1
= +
+
R R1 R2 R3
Optional Science - 10
P HYS I CS
----V--_.
Switch
--=d-n-~
+
fig:parallel connection of resistors
Characteristics of parallel connection of resistors
1.
There is a separate conducting path for all resistors in a parallel circuit.
2.
The potential difference across individual resistors is the same.
3.
The current through different resistors is different. The total current I = I1 +I2 +I3.
4.
The sum of the reciprocal of the resistance of individual loads is equal to the reciprocal
1
1
1 1
= +
of the equivalent resistance. i.e.,
+
R R1 R2 R3
Advantages of parallel connection
In parallel connections, each resistor or electric load has a separate circuit for the flow of
electricity. So
1.
A separate switch can be used for an individual resistor. In a domestic circuit, electrical
appliances can be operated independently.
2.
If one resistor stops working due to some defect, then all others keep working normally.
3.
Each resistor gets the same voltage. For example in our domestic circuit, all appliances
have the potential difference of 220 V as that of the power supply line.
4.
The overall resistance of the resistors gets reduced. Due to this, the current from the
power supply is high.
Know the Reason
In our domestic circuit, when one bulb burns out, the other bulbs in the circuit remain
lit, why?
Electric loads are connected in parallel in a domestic circuit. Each bulb has a separate
conducting path for current. So, in our domestic circuit, when one bulb burns out, the
other bulbs in the circuit remain lit.
Solved numerical- 6.
Resistors of 10Ω, 15Ω and 20Ω, are first connected in series and then in parallel. Calculate their
equivalent resistances in both the cases.
Solution: Here, Resistance of the first resistance (R1) = 10Ω
Resistance of the first resistance (R2) = 15Ω
Resistance of the first resistance (R3) = 20Ω
In a series circuit, the equivalent resistance is given by
R = R1 +R2 +R3Substituting the value of R1, R2 and R3
R = 10 + 15 + 20 = 35Ω,
In parallel circuit, the equivalent resistance is given by
1
1
1 1
= +
+
R R1 R2 R3
1
1
1
1
6+4+3
13
= +
+
=
=
Or
R 10 15 20
60
60
60
= 4.6 Ω
∴
R=
13
P HYS I CS
Optional Science - 10
117
Diodes
A diode is a two terminal electric
component that allows electric current
to flow in only one direction. One of its
"'
electrodes is positively charged whereas
the other is negatively charged. A diode
Generic Diode
Zener Diode
Schottky Diode
allows an electric current to pass in one
direction but blocks the current in the
~
opposite direction. So a diode can be
considered as a check valve in electronic
LED
Tunnel Diode
Photo Diode
devices. Thermionic diodes were an early
fig:Different types of diode
form of diode. Modern diodes are semiconductor diodes.
#
/
Thermionic diode/ vacuum tube diode
The method in which a metal is heated to a high temperature to make the
free electrons in the metal gain kinetic energy sufficient to escape through its
surface is called thermionic emission. The higher the temperature, the greater
is the emission. Thermionic diodes are electron tubes in which electronic
conduction occurs. It is also known as a vacuum tube diode. John Ambrose
Fleming invented the first true thermionic diode, the Fleming valve, in 1904. It
consists of a sealed evacuated glass envelope containing two main parts. They
are the cathode and anode, or metal plate.
Anode
Heated
cathode
Heater
fig:vacuum tube
diode
Semiconductor diodes
Most types of vacuum tube diodes have been replaced by semiconductor diodes. Semiconductor
diodes were the first semiconductor electronic devices. The first semiconductor diodes, called
cat’s whisker diode, was developed around 1906. A semiconductor diode is the most common
type of diode in use. Before you learn about the semiconductor diode, an introduction to the
semiconductor and its types is given here.
Semiconductor
A semiconductor is a solid substance that has conductivity between that of an insulator and
most metals. Such effect is either due to the addition of an impurity or because of temperature
effects. Silicon, germanium and selenium are the best known examples of semiconductors.
The electrical resistance of semiconductors lies in between the resistance of typical metals
and insulators. Devices made of semiconductors, notably silicon, are essential components of
most electronic circuits.
Types of semiconductors
Semiconductors can be classified into two types - intrinsic semiconductor and extrinsic
semiconductor - on the basis of their purity.
Semiconductor
f
0
118
t
Intrinsic or pure semi-conductor
Extrinsic or impur semiconductor
P-Type e.g. Boron doped silicon
N-Type e.g. Antimony doped silicon
Optional Science - 10
P HYS I CS
Intrinsic Semiconductor: A semiconductor in it pure form is known as an intrinsic
semiconductor. For example, silicon and germanium crystals in their natural state are intrinsic
semiconductors. There are four valence electrons in the atoms of these semiconductors. In a
germanium crystal, each of the four valence electrons of every
atom are shared with electrons of neighboring atoms. There
are no free electrons. When some bonds break up due to
thermal agitation, then electrons are liberated. Along with the
formation of free electrons, there is formation of a vacant space
called the hole. These electrons and holes in an intrinsic
semiconductor are called intrinsic carriers. Thus the
conductivity of an intrinsic semiconductor is very low, and Sharing of electrons
fig:intrinsic semiconductor
they are not used practically as semiconductors.
Extrinsic semiconductor: In order to increase conductivity, impurities are added to intrinsic
semiconductors. The process of adding impurities to pure semiconductors is called doping.
Such doped semiconductors are called extrinsic semiconductors. Impurity atoms are of two
types:
i.
Pentavalent impurity atoms: Pentavalent impurity atoms have 5 electrons in their
valence shell. For example, phosphorous (P), antimony (Sb), arsenic (As) can be used as
pentavalent impurity elements in an intrinsic semiconductor.
ii.
Trivalent impurity atoms: Trivalent impurity atoms have 3 electrons in their valence
shell. For example, boron (B), aluminium (Al), gallium (Ga) can be used as trivalent
impurity elements in an intrinsic semiconductor.
Types of Extrinsic Semiconductors
On the basis of the impurity atom added to an intrinsic semiconductor, there are two types of
extrinsic semiconductors: N-type semiconductor and P-type semiconductor.
N-type semiconductor
When a pentavalent impurity atom is added to an intrinsic semiconductor, then out of five
electrons, four electrons form a covalent bond with 4 valence
··•·
\
• Donar Impurity
electrons of 4 atoms of silicon or germanium. Due to this, the
Contributes Free
th
··• ·.. :e :: ::• :...... ·• ·· .. _~ectrons
5 electron of the impurity atoms remains free to conduct
electricity. Therefore, negatively charged electrons are the
Sb
•
~
charge carriers in N-type semiconductors. Thus, an extrinsic
·
··· .·.• :::. ·•·. ··
··
Added •
♦
semiconductor, which is created by doping an intrinsic Antimony
as Impurity
..
semiconductor with a pentavalent impurity element like
·
fig:n-type semiconductor
phosphorous (P), in which electrons are the majority carriers
and holes are the minority carriers, is called a N-type semiconductor.
y
•
... •..
.
•
. . .. •
..
.
··• ··
P-type semiconductor
When a trivalent impurity atom is added to an intrinsic
semiconductor, then three electrons form a covalent bond with
3 valence electrons with atoms of silicon or germanium. Due to
this, one vacancy is created. Thus for every trivalent impurity
atom, an extra hole will be created. Therefore, positively
charged holes are the charge carriers in P-type semiconductors.
P HYS I CS
•
•
•
.... .
· ·• ·· · .
•
Acceptor Impurity
. : :o; :~ ~atesa Hole
..•... .·.• :::.•· ..•...
.
B
•
·
··
Boron Added
as Impurity
j
··
iii •
·
••
. .•.
•
·
·.
fig:p-type semiconductor
Optional Science - 10
0
119
The silicon or germanium crystal so obtained is called a P-type semiconductor. Each hole is
equivalent to a positive charge. Thus, an extrinsic semiconductor, which is created by doping
an intrinsic semiconductor with a trivalent impurity element like boron (B), in which holes are
the majority carriers and electrons are the minority carriers, is called a P-type semiconductor.
P-N junction diode
A PN junction diode is a two terminal device whose one side is made a P-type semiconductor
and another side an N-type semiconductor by doping on an intrinsic semiconductor. It is
formed by placing a P-type semiconductor crystal in contact with an N-type crystal and
subjecting it to a high pressure so that it becomes a single piece. The layer model and circuit
symbol of a P-N junction diode are shown in the given figure. In the case of a P-N junction
diode, conventional current flows from the P-type to the N-type segment of the diode. It is
against the direction of electron flow.
At the junction of the two types of semiconductors, there is diffusion of electrons and holes.
During diffusion, electrons are removed from the N-type semiconductor and holes are added.
Similarly, the P-type semiconductor loses its holes and acquires electrons. This continues till
n equilibrium is established at the junction. The region free from any charge carrier, which is
formed by the diffusion of electrons and holes at the junction of a P-N junction diode, is called
the depletion layer. Due to neutralization of the charge carriers at the junction, the P-section
of the junction becomes slightly negative while the N-section becomes slightly positive. The
potential difference thus developed across the junction is called a potential barrier. It stops
further neutralization of charge carriers. The potential barrier is approximately 0.5V to 0.7V
for silicon diodes and approximately 0.3 V for germanium diodes.
Forward biasing and reverse biasing of a junction diode
Anode
I
► Cathode
Schematic Symbo l
Stripe m a rks cathode
Re a l compo ne nt
appearance
P-N junction diode symbol with its terminals
C atho de (K)
An ode (A )
-~
+
~
Anode
..
Convent ional Current Flow
Cathode
• •
Anode
►lcath:de
~
---
Closed c ircuit
Open c ircuit
Forward biased
Reverse biased
conventional current flow
forward biasing and reverse biasing
A junction diode can be biased in the following two ways:
1.
Forward bias: When a battery is connected to the P-N junction diode with the P-section
connected to the positive terminal and N-section to the negative terminal, the diode is
said to be forward biased.
2.
Reverse bias: When a battery is connected to the P-N junction diode with P-section
connected to the negative terminal and N-section to the positive terminal, the diode is
said to be forward biased.
Advantages of P-N junction diode over vacuum tube diodes
1.
P-N junction diodes are very compact due to their small size.
2.
They are cheaper than the cost of a vacuum tube.
3.
They have very long life.
4.
They are shock proof.
0
120
Optional Science - 10
P HYS I CS
Disadvantage of a semiconductor diode
The main disadvantage of a semiconductor diode is the possibility of its breakdown due to
rise in the temperature and on the application of high voltage.
Applications of diodes
1.
Radio demodulation: The audio is extracted from the modulated radio signal by using
diodes.
2.
Power conversion: The rectifiers which convert alternating current (AC) into direct
current (DC) are constructed from diodes.
3.
Over-voltage protection: Diodes are used for protection from over-voltages at high
power.
4.
Temperature measurement: The forward voltage drop across a diode depends on the
temperature. So a diode can be used as a temperature measuring device.
5.
Uninterrupted power supply (UPS): A diode can be used in an UPS to ensure that
current is only drawn from the battery when necessary.
Transistor
The transistor moved the world from power-hungry vacuum tubes to portable solid-state
electronics. Vacuum tubes were the basic components of electronic devices throughout the
first half of the 20th century. They were used in the advancement of the radio, television, radar,
sound amplification, sound recording and reproduction, large telephone networks, analog
and digital computers, and industrial process control. Invention of the vacuum tube made
these technologies widespread and practical.
In the 1940s, the invention of semiconductor devices made it possible to produce solidstate devices. The first practically implemented semiconductor device was a point-contact
transistor invented in 1947 by American physicists John Bardeen, Walter Brattain and William
Shockley. Such devices are smaller, more efficient, more reliable, more durable and cheaper
than vacuum tubes. From the mid-1950s, solid-state devices, such as transistors, gradually
replaced the tubes. However, there are still a few applications for which vacuum tubes are
preferred to semiconductors, for example, the magnetron used in microwave ovens, and
certain high-frequency amplifiers.
A transistor is a semiconducting device equivalent to a triode valve. A transistor is a three
terminal semiconductor electronic device with a P-type or N-type semiconductor region
sandwiched in such a way that there is formation of two P-N junctions. Transistors are widely
used to amplify electronic signals and switch electrical power.
Construction
In a P-N junction diode, there are two doped elements, namely the P-type semiconductor and
N-type semiconductor. A transistor is formed when a third doped element, either a P-type
semiconductor or N-type semiconductor, is added to a P-N junction diode in such a way that
there is formation of two P-N junctions. Thus a transistor is made by the following two ways:
i.
Sandwiching a P-type semiconductor between a pair of N-type semiconductors.
ii.
Sandwiching a N-type semiconductor between a pair of P-type semiconductors.
P HYS I CS
Optional Science - 10
121
Three sections of a transistor
Emitter, base and collector are the three sections of a transistor. All these three regions are
provided with terminals which are labeled E (for emitter), B (for base) and C (for collector)
respectively. A brief description of these terminals is given in the following points:
i.
Emitter (E): The section on one side that supplies the
charge carriers, which are either electrons or holes,
is called the emitter. The emitter is thinner than the
collector, but much thicker than the base. It is heavily
doped. In a circuit, it is denoted by E or e.
The emitter is always forward biased with respect to
the base. In the given figure, the P-type emitter of the
transistor is forward biased. It supplies holes to its
junction with the base. In the second figure, N-type
emitter of the transistor is forward biased. It supplies
free electrons to its junction with the base.
Function of emitter: Its main function is to supply
majority charge carriers to other regions.
Emitter~ e c t o r
l Ba■e
_ .,
Emitter~ l e c t o r
l
Base
three regions in NPN and PNP transistors
symbol of NPN
transistor
symbol of PNP
transistor
Know the Reason
The emitter of a transistor is heavily doped, why?
The emitter is heavily doped and always forward biased with respect to the base so that
it can supply a large number of majority carriers.
ii.
Base (B): The base is the middle region of a transistor. It is the thinnest region and
lightly doped. It is equivalent to the grid in a triode as it performs a function similar to
it. The emitter-base is always forward biased while collector-base is reverse biased. In a
circuit it is denoted by B or b.
Function of base: Its main function is to pass the majority charge carriers injected from
the emitter on to the collector.
Know the Reason
The base of a transistor is lightly doped, why?
Some electrons and holes combine in the base region. So the base of a transistor is lightly
doped to minimize the recombination of electrons and holes.
iii.
Collector (C): The collector is situated on the other side of the emitter on a transistor. It
is the thickest region. It is a moderately doped region. The collector is made thick so as
to dissipate the heat produced in the collector circuit. In a circuit, it is denoted by C.
Function of collector: The main function is to collect the majority charge carrier supplied
by the emitter and passed by the base.
122
Optional Science - 10
P HYS I CS
Application of transistors
Transistors are employed in approximately all digital circuits. Common applications of a
transistor are seen in analog and digital switches, power regulators, signal amplifiers and
equipment controllers. Microprocessors over and over again comprise more than a billion of
transistors in every single chip. Switching and amplification are the two types of applications
of a transistor.
Transistor as a switch: In transistors, current flows in collectors only when current flows in
the base circuit. This property is applicable while using a transistor as a switch.
a.
In a light-operated switch, the transistor is used to design a circuit to light the bulb in a
bright environment and to turn it off in the dark.
b.
It is used in a circuit of a heat-operated switch along with a thermistor as in a fire alarm.
c.
In digital electronics, it is used as a high speed electronic switch as in an Integrated
Circuit (IC).
Transistor as an amplifier
a.
Transistors are used in many electronic devices to amplify current as in microphones.
b.
In a communication system, it is used as the primary component in an amplifier.
Answer writing skill
1.
I
What is a step-up transformer?
A transformer which converts the applied low voltage AC to high voltage AC is called a
step-up transforer.
2.
Mention an important feature of a DC generator.
In a DC generator, two ends of the coil are connected to two copper half rings, or split
rings, R1 and R2 of a commutator.
3.
Write four differences between a diamagnetic substance and a paramagnetic substance.
Diamagnetic substance
Paramagnetic substance
A diamagnetic substance is feebly repelled A paramagnetic substance is feebly
by a magnet.
attracted by a magnet.
In a non-uniform magnetic field, the In a non-uniform magnetic field, the
diamagnetic substance is repelled towards paramagnetic substance is attracted
towards the stronger part of the field.
the weaker part of the field.
The permeability is less than one but can The permeability is slightly greater than
never be negative.
one.
The intensity of magnetization (I) has a The intensity of magnetization (I) has a
small negative value for a diamagnetic small positive value for a paramagnetic
substance.
substance.
P HYS I CS
Optional Science - 10
0
123
4.
Mention the effect on a freely suspended rod of diamagnetic, paramagnetic and
ferromagnetic material in a magnetic field.
5.
a.
A diamagnetic rod freely suspended in a uniform magnetic field, slowly turns to
set at right angle to the applied magnetic field
b.
When a rod of paramagnetic substance is freely suspended, in a magnetic field, it
aligns along the field.
c.
When a rod of a ferromagnetic substance is freely suspended in a uniform
magnetic field, it rotates and aligns itself parallel to the field.
The p.d. of the power supply to the primary coil of a transformer is 220 V and the
turns in the primary coil are 2000. What must be the number of turns in the secondary
coil to run a radio of 11 V from the transformer?
Solution
Here, Primary voltage (V1 ) = 220 V
Secondary voltage (V2 ) = 11V
Primary turns ( n1) = 2000
Secondary turns ( n2) = ?
Now,
The number of secondary turns is given by the formula
Or,
Secondary voltage (V2) Secondary turns (n2)
=
Primary voltage (V1)
Primary turns (n1)
n2 =
V2 × n1 2000× 11
= 100 V
=
V1
220
The number of turns in the secondary coil must be 100.
6.
Explain the operating principle of a transformer. Also mention the reason of why a
transformer does not work with DC.
Alternating current passes through the primary coil when it is connected to an AC
source. Hence, a magnetic field is produced by the primary coil. The magnetic field
due to A.C. in primary coil changes in both magnitude and direction. This changing
magnetic field changes the magnetic lines of force linked with the secondary coil.
According to the faradays laws of electromagnetic induction, whenever the magnetic
lines of force linked with a closed circuit changes, an e.m.f. gets induced from two
terminals of the secondary coil. Thus, the induced current is also an alternating current.
Instead of AC, if DC is supplied in the primary coil then the magnetic field produced is
of constant strength. The number of magnetic lines of force which are intersected by the
secondary coil does not change. In such condition current does not get induced from the
two terminals of secondary coil. Thus, transformer does not work with DC.
0
124
Optional Science - 10
P HYS I CS
Exercise
Step
1
Define
1. Magnetization
2. Magnetic permeability
3. Magnetic susceptibility
4. Diamagnetic material
5. Paramagnetic material
6. Ferromagnetic material
7. Magnetic flux
8. Fleming’s right hand rule 9. Primary voltage
10. Primary coil
11. Secondary coil
12. Secondary voltage
Very short answer questions
1.
Give four examples each of
a.
diamagnetic materials
b. paramagnetic materials
2.
c. ferromagnetic materials
Name two of the strongest diamagnetic materials
3.
What is electromagnetic induction?
4.
Name the two devices which are based on
5.
a. electromagnetic induction
What is a bicycle dynamo?
6.
What is an electric generator?
7.
What is meant by magnetic effect of current?
8.
Name the scientist who discovered
9.
a. the magnetic effect of current
What is an electric motor?
10.
Name the main elements in:
11.
a. AC generator
What is a transformer?
12.
Name the two types of transformers on the basis of number of windings.
b. motor effect
b. electromagnetic induction
b. DC generator
P HYS I CS
Optional Science - 10
125
13.
Write the working principle of the
a.
generator
b. electric motor
14.
c. transformer
What is a resistor?
15.
Give two ways to connect resistors in a circuit.
16.
What is a diode?
17.
Name the electrodes used in a diode.
18.
What is a transistor?
Step
2
Short answer questions
1.
State molecular theory of magnetism.
3.
‘Frequency of the power supply in a domestic circuit is 50 Hz’. What does it mean?
4.
Write the Faraday’s three laws of electromagnetic induction.
5.
What change occurs in the brightness of a bulb connected to a bicycle dynamo when the
wheel’s speed of rotation increases?
6.
Mention the factors on which the strength of the induced current depends?
7.
Write four methods to increase the strength of the current generated from a dynamo or
generator.
8.
Make a comparison between DC motor and DC generator in two points.
9.
Mention four characteristics each of
a.
Series connection of resistors
b. Parallel connection of resistors
10.
Write two advantages and two disadvantages each of
11.
a. Series connection of resistors
b. Parallel connection of resistors
What do the three fingers, namely thumb, fore finger and middle finger indicate in
Fleming’s right hand rule
12.
Write two applications each of the
a.
c.
13.
electric generator
Diode.
b. electric motor
d. transistors
e. step-up transformer
f. step-down transformer
Write the two laws in which a transformer is based on.
14.
‘Use of alternating current would be limited in the absence of a transformer’. Justify this
statement.
15.
Write in short about the following three sections of a transistor with their function
0
a.
Emitter (E)
c.
Collector (C)
126
Optional Science - 10
b. Base (B) P HYS I CS
Differentiate between
1.
AC and DC
2.
Electric generator and electric motor
3.
AC generator and DC generators
4.
AC motor and DC motor
5.
Step-up transformer and step-down transformer
6.
Series connection of resistors and parallel connection of resistors
7.
Intrinsic semiconductor and extrinsic semiconductor
8.
N-type semiconductor and P-type semiconductor
Give reason
1.
In a series connection and parallel connection, the parallel connection of resistors
decreases the total resistance of the circuit.
2.
A stationary magnet does not induce a current in a coil.
3.
The core of a transformer is laminated.
4.
The number of turns in the primary coil and secondary coil of a transformer is different.
5.
Transformer does not alter the voltage of direct current (DC).
6.
In our domestic circuit, when one bulb burns out, the other bulbs in the circuit remain
lit.
7.
A diode is called a valve in an electronic circuit.
8.
A vacuum tube diode blocks the negative half cycle of AC
9.
The emitter of a transistor is heavily doped.
10.
The base of a transistor is lightly doped.
Answer the questions with the help of the given figure
1.
In the given figure, a copper wire is being moved perpendicular to the magnetic lines of
force in the U-shaped magnet. Two ends of a wire are connected in Galvanometer.
a Why does the Galvanometer show deflection due to the
movement of the wire?
b. Write any two ways that the deflection of the Galvanometer
can be increased.
c. What will happen when the Galvanometer is replaced by
a battery? What is the effect called?
Laminated Iron Core
2.
Which type of transformer is given in the picture?
b. Write any one application.
c. Calculate the voltage produced in the secondary coil.
220 V
100turns
1000 turns
[Ans: 22 V]
P HYS I CS
Optional Science - 10
0
127
3.
Which effects are shown in the given figure ‘a’ and ‘b’? Write any two applications of
each.
-<E------ current
direction
magnetic
fields in
-<E-------the same
direction
repel
wire pushed
in this
direction
wire
a
Step
b
3
Numerical problems
1.
A transformer of 1000 primary turns is connected to a 220 V AC supply. How many turns
of the secondary coil will be needed in order to generate 110 V from that transformer?
[Ans: 500 ]
2.
The power supply is of 240 V and the number of turns in the primary coil of a transformer
is 1000. What should be the number of secondary turns to generate an output of 12V, 24
V and 120 V?
[Ans: 50, 100, 500 turns]
3.
A transformer has 600 turns of wire in the primary coil and 1200 turns of wire in the
secondary coil. The potential difference across the primary coil is 110 V. What is the
potential difference induced across the secondary coil? [Ans: 220 V]
4.
The number of turns in the primary and secondary coils of a transformer is 1200 and 300
respectively. If secondary voltage is 55 V, then, calculate its primary voltage.[Ans: 220 V]
5.
In a transformer the secondary turns are 4 times more than the primary turns. What
should be the input voltage in the transformer to obtain an output of 220 V?
[Ans: 55 turns]
6.
In a transformer, the ratio of secondary turns to primary turns is 2:3. Which type of
transformer is it? Find the secondary voltage when the transformer is connected to a
power supply of 220 V.
[Ans: 146.667 V]
7.
An input voltage and output voltage in a transformer are 12 V and 220 V respectively.
What is the current in the primary coil when the output current is 0.75 A?[Ans: 13.75 A]
8.
A step-up transformer has 5,000 turns on its secondary coil and 100 turns on its primary
coil. An alternating current of 5 A flows in the primary coil when it is connected to a 12
V AC supply. Calculate
128
1.
The power input to the transformer
2.
The emf induced across the secondary coil.
3.
Current in the secondary coil.
Optional Science - 10
P HYS I CS
[Ans: 60 W, 600V, 0.1 A]
Draw a diagram
1.
Draw a diagram to show the pattern of magnetic lines of force when
a.
a diamagnetic material is placed within a magnetic field
b.
a paramagnetic material is placed within a magnetic field
3.
c.
a ferromagnetic material is placed within a magnetic field
Draw a diagram to show the magnetic field around a straight current carrying wire.
4.
Draw a diagram to show electromagnetic induction.
5.
Draw a labeled diagram to show the construction of a bicycle dynamo.
6.
Draw a diagram to show the current time relation in the case of
7.
a. alternating current b. direct current
Draw a diagram to show the construction of
8.
a. AC generator
b. DC generator
Draw a diagram to show the direction of three fingers and their corresponding indication in
Fleming’s right hand rule
9.
Draw a labeled diagram to show the construction of a step-up transformer and stepdown transformer.
10.
Draw a labelled diagram and corresponding symbol of P-N junction diode.
Step
1.
Explain the main characteristics of
a.
2.
4
diamagnetic substance
b.
paramagnetic substance
c.
ferromagnetic substance
Mention the main characteristics of a paramagnetic substance which are opposite of
diamagnetic substances.
3.
Make a comparative study of ferromagnetic substances with paramagnetic substances
and diamagnetic substances.
4.
Explain an experiment to demonstrate electromagnetic induction.
5.
Describe the construction and working of the following:
a.
6.
Bicycle dynamo b. AC generator.
c. DC generator
d. DC motor
e. transformer
Explain the role of the transformer in changing the voltage of an alternating current.
P HYS I CS
Optional Science - 10
0
129
Multiple choice question [MCQ]
1.
The magnetic substances which are strongly attracted by a magnet are
a.
2.
diamagnetic substance
b. ferromagnetic substance
c. paramagnetic substance
Frequency of AC in our domestic circuit is
d. none of above
a.
b. 60 Hz
50 Hz
c. 240 Hz
Bicycle dynamo converts
3.
d. 220 Hz
a.
mechanical energy into magnetic energy.
b.
electrical energy into magnetic energy.
c.
mechanical energy into electrical energy.
d. electrical energy into mechanical energy
Principle of dynamo is
4.
a.
electromagnetic induction
b. motor effect
c. Ohm’s law
d. mutual induction
The primary coil of a step-down transformer has:
5.
6.
a.
less number of turn
b. more number of turns
c.
very less
e. all of the above
The transformer formula is
a.
V 1 n2
=
V 2 n1
b.
V2 v1
=
n1 n2
c.
V 2 n1
=
V 1 n2
d.
V 2 n2
=
V 1 n1
Project Work
1.
Make a model of DC generator: Buy a DC electric motor. Connect a small low power LED
bulb to two terminals of the connecting wires. Now rotate the shaft of the motor by
your hand. Do you observe the bulb glowing with changing brightness? What happens
to the brightness of the bulb when you rotate it faster? Discuss in your group to draw a
conclusion.
2.
Visit an electric workshop and request the motor repair person to show you the parts of a
DC and AC motor. Observe their parts and note them. Finally note their working method
and present your study in the class.
130
Optional Science - 10
P HYS I CS
UNIT
7
ATOMIC
STRUCTURE
About the inspiring personality: John Dalton born in September 6, 1766, in Eagles field,
England. He died on July 26, 1844 in Manchester, England. He was the greatest scientist
in his time. The modern atomic theory was first formulated by John Dalton. So, he is well
known from the Dlalton atomic theory. The sex-linked disease, viz. colour-blindness was first
studied by John Dalton. John Dalton also proposed a concept of Partial Pressures in 1803,
which is known as Dalton’s Law of Partial pressure.
Syllabus issued by CDC
Learning objectives:
At the end of this unit, the students will be able to:
• Explain atomic mass, molecular mass and
mole concept.
Atomic mass, molecular mass and • Explain Avogadro’s number and Quantum
number.
mole concept
•
Describe normality, molality, molarity,
Quantum numbers
grams per litre and percentage along with
Concentration
(Normality,
the calculation of these quantities in some
molarity, gram per litre and
chemical compounds.
percentage)
Theory
Practical
•
•
•
6
2
Key terms and terminologies of the unit
1.
2.
3.
4.
Atom: An atom is the smallest particle of an element which can neither be created
nor be destroyed and involves in chemical reaction without division.
Atomic mass: The total mass of protons and neutrons which are present in the
nucleus of an atom is called atomic mass.
Amu: Amu is a unit of mass which is used to measure the mass of very small
particles like atoms, electrons, protons, neutrons, etc. It is equal to the mass of
1/12th of mass of carbon-12 isotope.
Molecular formula: The symbolic representation of one molecule of a substance
is called molecular formula.
C HEMI S TRY
Optional Science - 10
131
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
24.
25.
26.
0
132
Molecular mass: The sum of atomic mass of all atoms present in a molecule is
called molecular mass.
One mole: The amount of substance which contains 6.022 × 1023 atoms, ions,
molecules or even sub-atomic particles is called one mole.
Molar mass: The total amount of mass present in one mole of a pure substance is
called molar mass. Its SI unit is gram per mol.
Avogadro’s Number: Avogadro’s Number is the number of atoms, molecules,
ions or particles present in one mole of a pure substance. It is equal to 6.022 × 1023.
Orbital: The region around the nucleus where there is high probability of finding
the electrons is called orbital.
Quantum number: The characteristics of an electron and its position are
determined by a set of specific number called quantum number.
Principal quantum number: Principal quantum number represents the main
energy level or shell to which the electrons belong to.
Azimuthal quantum number: Azimuthal quantum number describes the angular
momentum of an electron and shape of the orbital or sub-shell.
Magnetic quantum number: Magnetic quantum number is the third set of
quantum number which describes the orientation of the sub-shells.
Solution: The homogeneous mixture of solute and solvent is called solution.
Concentration: The amount of solute dissolved in a given amount of solvent is
called concentration.
Percentage by mass: The amount of solute present in 100 g of solution is called
percentage by mass.
Percentage by volume: When the amount of dissolved solute is measured in gram
(g) and the amount of solution is measured in 100 millilitres (mL), it is called
percentage by volume.
Percentage by volume: When the amount of dissolved solute is measured in mL
and prepared solution is measured in 100 millilitres (mL), it is called percentage
by volume.
Grams per litre: The mass of solute in gram present in one litre of solution is called
grams per litre.
Molarity: Molarity (M) is the number of moles of solute present in one litre of
solution.
Molar solution: The solution containing one mole of solute in one litre solution is
called molar solution.
Decimolar solution: If a solution contains 1/10 mole of a solute in one litre solution,
then it is called decimolar solution.
Molality (m): The number of moles of solute present in one kilogram of solvent is
called molality (m).
Normality (N): The number of equivalents of a solute present in one litre of
solution is called normality (N).
Normal solution: The solution containing one equivalent of solute in one litre of
solution is called normal solution.
Decinormal solution: The solution containing 1/10 equivalent of solute in one litre
of solution is called decinormal solution.
Optional Science - 10
C HEMI S TRY
Introduction
There are different kinds of matter around us. Examples: soil, rock, book, pen, pencil, clothes,
medicine, etc. Among them some are natural and some are man-made, some are pure and
some are impure. The elements and compounds are pure matter and others are impure matter.
Elements are made up of atoms and compounds are made up of molecules. Atoms are the
smallest particles of elements. They can neither be created nor be destroyed. They involve in
chemical reaction without division. They are the building blocks of matter. They are the same
as bricks of a building. Thus, atom is the smallest particle of an element which can neither be
created nor be destroyed and involves in chemical reaction without division. The word atom
is derived from the Greek word “atomus”, it means indivisible particle. So, atoms cannot be
broken down into further simpler substances. All the atoms of an element are the same in all
aspects but atoms of different elements are different with each other. An atom is made up
of mainly three types of small particles called sub-atomic particles or fundamental particles.
They are electrons, protons and neutrons. In the structure of an atom, about 99% of an atom is
made up of empty space. The remaining 1% is made up of sub-atomic particles. So, the main
part of an atom is concentrated into a very small volume.
Memory Plus
In the structure of an atom there are two parts. They are shells and nucleus. Shells occupy
about 99% of the total volume and nucleus occupies only about 1%.
Atomic mass or atomic weight
In an atom, there are electrons, protons and neutrons. To calculate the total mass of an atom, the
mass of electrons, protons and neutrons should be added. So, atomic mass is the calculation
of the total mass of an atom. The protons and neutrons have about equal mass. But the mass
of an electron is very less. The mass of electron is about 1837 times smaller than a proton.
Therefore, the mass of an electron can be neglected while calculating the total mass of an atom.
It means that the mass of an atom is the sum of mass of protons and neutrons.
Actually, mass and weight are different things. Mass is the total amount of matter present in
a body. Its SI unit is kg. While weight is the amount of force applied by the earth to pull the
body. Its SI unit is newton (N). The bigger object has more mass and more weight. Similarly,
the smaller object has less mass and less weight. But for the smaller particles like the subatomic particles of an atom, viz. electrons, protons and neutrons, the mass and weight are
conventionally the same thing.
The total mass of protons and neutrons which are present in the nucleus of an atom is called
atomic mass. Generally, it is also called atomic weight. Atomic weight is usually measured in
atomic mass unit (amu). The mass of one proton or one neutron is equal to one amu. Therefore,
if an atom has six protons and six neutrons, then the atomic mass will be 12 amu. Amu is a
unit of mass which is used to measure the mass of very small particles, like protons, neutrons,
electrons or atoms. While calculating the mass of an atom, we count the total number of
protons and neutrons of an atom and calculate the total mass of that atom. In kilogram, the
mass of one proton or one neutron is nearly equal to 1.67 × 10-27 kg. This mass is equal to ¹/₁₂th
of mass of a carbon-12 isotope. This is also called atomic mass unit (amu). Thus, amu is a unit
of mass which is used to measure the mass of very small particles like protons, neutrons,
electrons or atoms. It is equal to the mass of ¹/₁₂ ᵗh of mass of carbon-12 isotope.
C HEMI S TRY
Optional Science - 10
0
133
Take an example of oxygen atom. In this atom, there are eight protons and eight neutrons
in its nucleus. After adding, the total number of protons and neutrons, it becomes sixteen.
Therefore, the mass of one oxygen atom is 16 amu. To express atomic mass of oxygen in
kilogram, it is necessary to multiply sixteen with 1.67× 10-27 kg.
Example: 1
Express atomic mass of hydrogen (1H1), sodium (11Na23), chlorine (17Cl35) and potassium
(19K39) in amu.
Solution:
For hydrogen, atomic mass = p + n
= 1+ 0 = 1 amu
For sodium, atomic mass
= p+n
= 11 + 12 = 23 amu
For chlorine, atomic mass
= p+n
= 17 + 18 = 35 amu
For potassium, atomic mass = p + n
= 19 + 20 = 39 amu
Molecular mass or molecular weight
Molecules are the smallest particle of a compound. They can exist independently. They show
all the properties of the compound. They are represented using formula. Examples: water
(H2O), sodium chloride (NaCl), calcium carbonate (CaCO3), sulphuric acid (H2SO4), glucose
(C6H12O6), etc. Thus, the symbolic representation of one molecule of a substance is called
molecular formula. Molecules may be monoatomic, diatomic, triatomic or polyatomic. In case
of monoatomic molecules like helium, neon, argon, krypton, xenon and radon the formula for
atom and molecule is the same. The atomic mass and molecular mass for these inert gases is
also same.
Fact with reason
Inert gases are called monoatomic molecules. Why?
The atoms of inert gases like helium, neon, argon, krypton, xenon, radon, etc. can exist
independently. They do not combine with other atoms. So, atoms of these elements are
called monoatomic molecules.
In case of diatomic, triatomic and poly atomic molecules, the molecular mass is calculated
by adding the atomic mass of all atoms of the molecule. For this, it is necessary to calculate
total number of atoms of different elements present in the molecule. As we have already
discussed that the mass of an atom can be calculated by adding the total number of protons
and neutrons present in the nucleus of that atom. The same concept can also be used to
calculate the molecular mass of a compound. To illustrate above concept, let us take a
methane molecule (CH4). This molecule has one carbon atom and four hydrogen atoms. So,
the total mass of methane is equal to the mass of one carbon atom and four hydrogen atoms.
0
134
Optional Science - 10
C HEMI S TRY
The atomic mass of carbon atom is 12 and hydrogen atom is 1. Therefore, the total mass of
methane molecule is 12 + 4 or 16 amu. Similarly, the mass of carbon dioxide (CO2) is equal to
1 × mass of carbon atom + 2 × mass of oxygen atoms. It is equal to 1×12 + 2×16 amu or 44 amu.
From the above discussion it is clear that, the sum of atomic mass of all atoms present in a
molecule is called molecular mass. For example, the molecular mass of hydrogen molecule is 2
amu. It means that hydrogen molecule is 2 times heavier than ¹/₁₂th mass of carbon-12 isotope.
Similarly, the molecular mass of sulphuric acid is 98 amu. It means that, sulphuric acid is 98
times heavier than the ¹/₁₂th mass of carbon-12 isotope.
Fact with reason
The molecular mass of oxygen molecule is 32 amu. What does it mean?
The molecular mass of oxygen molecule is 32 amu. It means that, the sum of atomic mass
of oxygen molecule is 32 or it is 32 times heavier than 1/12th mass of carbon-12 isotope.
Example: 2
Calculate molecular mass of calcium sulphate (CaSO4).
Molecular mass of CaSO4
= 1×Ca + 1×S + 4×O
= 1×40 + 1×32 + 4×16
= 40+32+64
= 136 amu
Example: 3
Calculate molecular mass of calcium carbonate (CaCO3).
Molecular mass of CaCO3
= 1×Ca + 1×C + 3×O
= 1×40 + 1×12 + 3×16
= 100 amu
Example: 4
Calculate molecular mass of ammonium sulphate (NH4)2SO4
Molecular mass of (NH4)2SO4 = 2×N + 8×H + 1×S + 4×O
= 2×14 + 8×1 + 1×32 + 4×16
= 28 + 8 + 32 + 64
= 132 amu
Mole Concept
In our daily life, we use to buy and sell different things in terms of number or in terms of
mass (or weight) or in terms of volume. For example, we buy pen, pencil, book, exercise book,
biscuits, eggs, banana, etc. in terms of number and we buy sugar, rice, wheat, etc. in terms of
mass (or weight). Similarly, we buy different liquids like milk, oil, etc. in terms of volume.
To measure different quantities we use different kinds of measuring units such as kilogram,
gram, milligram, litre, millilitres, etc. It is not possible to count the numbers everywhere. For
example, we cannot count the number of wheat and rice grains while buying from the shop.
Similarly, atoms, molecules, ions, etc. are so small particles that we cannot count. So, chemistry
introduced "mole" to measure these quantities.
C HEMI S TRY
Optional Science - 10
135
In chemical reaction, fixed numbers of atoms or molecules or ions react to given a fixed amount
of products. For example, two molecules of hydrogen and one molecule of oxygen react together
to given two molecules of water. If we take only one molecule of hydrogen and one molecule of
oxygen, it does not give water. But it is very difficult to count the number of atoms or molecules
during the chemical reaction. This is because a small quantity of mater contains a large number
of particles or atoms or molecules or ions. To solve this problem, the mole concept has been
introduced. It is used to measure how much of a substance is present in a given sample. For a
reference of measurement we have chosen carbon-12 isotope. One mole of a substance contains
as many atoms or molecules or ions as there are in 0.012 kilogram or 12 grams of carbon-12
isotope. It has been calculated that, in 0.012 kilogram or 12 grams of carbon-12 isotope there are
6.022 × 1023 atoms. It is called one mole of carbon. Therefore, mole is a collection of very small
particles that includes atoms, ions, molecules or even sub-atomic particles like electrons, protons
and neutrons. The amount of substance which contains 6.022 × 1023 atoms, ions, molecules or
even sub-atomic particles is called one mole. The symbol of mole is "mol".
To understand the mole concept, let us consider an atom of oxygen, a molecule of oxygen, a
molecule of carbon dioxide and an ion of oxygen. According to atomic mass and molecular
mass, one atom of oxygen has 16 amu, one molecule of oxygen has 32 amu, one molecule of
carbon dioxide has 44 amu and one oxygen ion has 16 amu. Now, if we take one gram molecular
weight of these substances then we have 16 grams of oxygen atom, 32 grams of oxygen molecule,
44 grams of carbon dioxide and 16 grams of oxygen ion. The amount of matter present in these
substances (atom, molecule and ion) is called one mol. It can be further clarified as:
1.
16 gram of oxygen atom is also called one mole of oxygen atom.
2.
32 grams of oxygen molecule is also called one mole of oxygen molecule.
3.
44 grams of carbon dioxide molecule is also called one mole of carbon dioxide.
4.
16 gram of oxygen ion is also called one mole of oxygen ion.
Substances
Symbol
Mass in
amu
mass in
gram
mass in
mole
Number of
particles
Oxygen atom
O
16
16
1
6.022 x 1023
Oxygen molecule
O2
32
32
1
6.022 x 1023
44
44
1
6.022 x 1023
O
16
16
1
6.022 x 1023
Carbon dioxide molecule CO2
Oxygen ion
-2
The total amount of mass present in one mole of a pure substance is called molar mass. Its SI
unit is gram per mol.
Avogadro’s Number
As we know that Avogadro’s Number is the number of atoms, molecules, ions or particles
present in one mole of a pure substance. It is equal to 6.022 × 1023. The word Avogadro is
named after the honour of an Italian chemist Amedeo Avogadro who discovered this concept.
According to this concept one mole of a pure substance contains exactly equal number of
atoms or molecules or ions or sub-atomic particles which is numerically 6.022×1023. Now, the
number 6.022 × 1023 is called Avogadro’s number. It is denoted by a symbol (N0).
0
136
Optional Science - 10
C HEMI S TRY
Memory Plus
i.
Number of atoms in 14 grams of nitrogen atom (N) = Number of molecules in 28
grams of nitrogen molecule (N2) = Number of molecules in 17 grams of ammonia
molecule (NH3) = Number of ions in 14 grams of nitrogen ion (N-3).
ii. Number of molecules =
Mass of substance (m)× Avogadro's number
Molar mass (M)
Example: 1
Calculate the molar mass of KNO3 and find the number of molecules present in 5 mole of
KNO3.
Solution:
The molecular mass of KNO3 = 39 + 14 + 3 × 16 = 101 amu
Therefore, molar mass of KNO3 = mass of 1 mol of KNO3 = 101 gm/mole
The number of molecules in 1 mole of AgNO3 = Avogadro’s number = 6.022 × 1023 molecules
Hence, the number of molecules in 5 mole of KNO3 = 5 × 6.022 x 1023 = 30.31× 1023 molecules
Example: 2
Calculate the number of molecules present in 1 kg of carbon dioxide.
Solution:
1 kg of carbon dioxide = 1000 gram
As we know, 1 mole of carbon dioxide = 44 gram
= 6.022× 1023 molecules
6.22 × 1023
molecules
1 gram of carbon dioxide =
44
23
6.22 × 10
× 1000 molecules
So, 1000 gram of carbon dioxide =
44
=136.86 × 1023 molecules
=1.3686 × 1025 molecules
Example: 3
Calculate the total number of carbon atoms and hydrogen atoms present in 1 kg of methane
(CH4).
Solution:
1 kg of methane
= 1000 gram
As we know,
1 mole of methane
= 16 gram = 6.022 × 1023 molecules
16 grams of methane
= 6.022× 1023 molecules = 6.022× 1023 carbon atoms
6.22 × 1023
× 1000 carbon atoms
So, 1000 gram of methane
=
16
= 376.375 × 1023 carbon atoms
= 3.76 × 1025 carbon atoms
C HEMI S TRY
Optional Science - 10
0
137
Similarly, 1 mole of methane (CH4) = 16 gram = 6.022 × 1023 molecules = 4 × 6.022 × 1023
hydrogen atoms.
4 × 6.22 × 1023
× 1000 hydrogen atoms
So, 1000 gram of methane
=
16
= 1505.5 × 1023 hydrogen atoms
= 1.5 × 1026 hydrogen atoms
Quantum number
We use a detail address to send a letter for a particular person. For example, Alish Panthi,
Madane Village Politian -7, Bhanbhane, Chaurapata, Gulmi. In this address, it is easy to find
Mr. Alish Panthi. Similarly, to find the position and energy of an electron, we need some
special numbers called quantum number. According to Bohr’s model of atomic structure, an
electron lies at a fixed distance from the nucleus. It is believed that an electron revolves around
the nucleus from this distance. But, this concept is rejected by the quantum mechanical model
of an atom. According to quantum mechanical model, an electron can be anywhere within
a certain region around an atom and its position cannot be accurately predicted. The actual
position and velocity of an electron cannot be calculated at the same time. It is believed that
electron is present anywhere around the nucleus. Thus, the region around the nucleus where
there is high probability of finding the electrons is called orbital. There are four major types of
orbitals. They are s-orbital, p-orbital, d-orbital and f-orbital. But, knowing only these orbitals
is not sufficient to study about the position and energy of an electron. Every electron has a
certain amount of energy. So, it is located at a certain position around the nucleus. It also
spins in its own axis in a particular direction. These properties of an electron are studied by
using a set of numbers called quantum numbers. Thus, the characteristics of an electron and
its position are determined by a set of specific numbers called quantum numbers. Quantum
numbers are used to decide the position, angular momentum, orientation and spinning
property of an electron. There are four quantum numbers. They are:
1.
Principal quantum number (n)
2.
Azimuthal (or Angular momentum) quantum number (l)
3.
Magnetic quantum number (m)
4.
Spin quantum number (s)
The principal quantum number (n)
The principal quantum number represents the main energy level or shell to which the electrons
belong to. It decides the size of the shell and the average distance of the shell from the nucleus.
The principal quantum number is denoted by the symbol "n". It has non-zero values like 1,2,3,
4, etc. It is also called energy level or shell number. These numbers also give idea about the
comparison distance of the orbitals from the nucleus. For example, the principal quantum
number n = 3 lies at a greater distance from the nucleus than the number n = 2. Meanwhile,
n = 3 is at a greater distance, it forms a bigger region of the circle than n = 2. From the above
example, it is clear that the size of shell having higher value of quantum number is bigger than
the shell having lower value of quantum number. The letters K, L, M, N, etc. are also used to
decide the energy level or shells. The maximum number of electrons present in each shell is
calculated by using 2n2 formula. For example,
0
138
Optional Science - 10
C HEMI S TRY
Principal quantum number (n)
Letter symbol
Maximum number of electrons (2n )
2
1
2
3
K
L
M
2
8
18
The azimuthal quantum number (l)
Azimuthal quantum number describes the
Azimuthal quantum Sub-shells
angular momentum of an electron and shape of
number (l)
the orbital or sub-shell. It also describes electrons
0
s
cloud around the nucleus. It is symbolized by the
1
p
letter "l". For the given value of principal quantum
2
d
number, the value of azimuthal quantum number
may have all integral values from 0 to n-1 like 0,
3
f
1, 2, 3……. (n-1). These numbers refer to the subshells s, p, d and f for the numbers 0, 1, 2 and 3 respectively. The value of azimuthal quantum
number is upto one less than the principal quantum number along with zero. For example,
(1)
For principal quantum number (n) = 1, the azimuthal quantum number (l) = 0. It
represents s-orbital which is spherical in shape.
(2)
For n = 2, the value of l = 0 and 1. Here, the value 0 represents s-orbital and value 1
represents p-orbital.
(3)
Similarly, for n = 3, the value of l = 0, 1 and 2.
The summary of different azimuthal quantum numbers for principal quantum number
The value of principal
The value of azimuthal
The number
quantum number (n) quantum number (l) = n-1 of sub-shells
(starting from zero)
The symbol of subshells
1
0
1
s
2
0, 1
2
s and p
3
0, 1, 2
3
s, p and d
4
0, 1, 2, 3
4
s, p, d and f
The maximum number of electrons in each sub-shell can be calculated by using a formula
2(2l+1).
For example, in l = 2, the maximum number of electrons = 2 (2l+1) = 2 (2×2+1) =10. Here, l = 2
denotes d sub-shell which contains 10 electrons.
Magnetic quantum number (m)
The shape of the sub-shells (orbitals)
is described by the azimuthal quantum
number. However, the same shape of the
sub-shell can have different orientations
in the space. For example, the orientation
of px, py and pz is shown in the diagram
alongside.
z
z
z
y
Pr
p, orbital
C HEMI S TRY
Py orbital
Optional Science - 10
139
The same orbital having different orientation shows different effect in an atom. This effect
was first observed in presence of magnetic field. Therefore these numbers are called magnetic
quantum number. Magnetic quantum number is the third set of quantum number which
describes the orientation of the sub-shells. It is denoted by the letter "m". The magnetic
quantum numbers can have the values from –l to +l.
For example:
Azimuthal quantum
number (l)
0
0
Magnetic quantum
number (m)
1
-1, 0 +1
2
-2, -1, 0, +1, +2
Possible orientation
Single orientation as it is "s" orbital
Three orientations (px, py and pz) as it is "p"
orbital
Five orientations (dxy, dyz, dzx,dx2, dy2 and dz2)
as it is "d" orbital
Memory Plus
In p sub-shell there are a total of three boxes denoted by px, py and pz. Each box can
contain two electrons having opposite spin. So, p sub-shell can contain total 6 electrons.
Filling of electrons takes place first single in all boxes and then starts for doubling. For
example, if there are five electrons in p sub-shell, then electrons fill like
Spin quantum number (s)
Electron not only revolves around the nucleus but also spins about its own axis. It can be
compared with the revolution and rotation of the earth around the sun and along the axis
respectively. Electrons spin in two ways. They are clockwise and anticlockwise. The clockwise
spin is called up spin ( ). It is given by the value s = +¹/₂. Similarly, the anticlockwise spin is
called a down spin ( ) and it is given by the value s = -¹/₂. Thus, the quantum number which
indicates clockwise and anticlockwise spin of an electron is called spin quantum number.
Example: 1
Write down the value of quantum number for the last electron in the electronic configuration
3s1.
Ans : For 3s1
1.
Principal quantum number (n) = 3 (Because it is 3rd shell)
2.
Azimuthal quantum number (l) = 0 (Because it is s-subshell)
3.
Magnetic quantum number (m) = 0 (Because it is s-subshell which has single orientation)
4.
Spin quantum number (s) = +¹/₂(Because it is up spin)
Example: 2
What are the quantum numbers for the last electron of the chlorine atom.
Ans : For 1s2 , 2s2 2p6, 3s2 3p5
140
Optional Science - 10
C HEMI S TRY
1.
Principal quantum number (n) = 3 (Because it is 3rd shell)
2.
Azimuthal quantum number (l) = 1 (Because it is p-sub shell)
3.
Magnetic quantum number (m) = 0 (Because fifth electron lies in py)
4.
Spin quantum number (s) = -1/2 (Because it is down spin)
Example: 3
What are the quantum numbers for the seventh electron of the sodium atom.
Ans : For 1s2 , 2s2 2p6, 3s1
The seventh electron lies within 2p. So,
1.
Principal quantum number (n) = 2 (Because it is 2nd shell)
2.
Azimuthal quantum number (l) = 1 (Because it is p-sub shell)
3.
Magnetic quantum number (m) = -1 (Because seventh electron of sodium lies in pz)
4.
Spin quantum number (s) = +1/2 (Because it is up spin)
Solution
When two or more chemically non-reacting substances are added to each other, they form
a mixture. Mixture may be heterogeneous or homogeneous. In heterogeneous mixture, the
mixing components can be seen easily but in homogeneous mixture, the mixing components
cannot be seen by our naked eyes. Solution is an example of homogeneous mixture. Thus, the
homogeneous mixture of solute and solvent is called solution. In solution, the composition
can be varied within a certain limit. The solution which contains water as a solvent is called
aqueous solution. Similarly, the solution which contains solvent other than water like benzene,
ether, petrol, kerosene, etc. is called non-aqueous solution.
Concentration of the Solution
The amount of solute dissolved in a given amount of solvent is called concentration.
Generally, the relative concentration is denoted by "dil" for dilute solution and "conc" for the
concentrated solution. Dilute and concentrated are the relative terms. They do not indicate the
exact concentration of the solution. Hence, different concentration units are used to express the
exact concentration of the solution. Percentage, gram per litre, normality, molarity, molality,
mole fraction, etc. are some units of concentration. Among them, some are explained below.
1. Percentage
Percentage is used to express the mass or volume of solute present in 100 g or 100 mL of
solution. The percentage composition is the expression of mass of solute in 100 parts of
volume of the solution. The percentage composition is written as:
i.
Percentage by mass (% w/w)
Rohan scored 65 % in class IX final example. It means, he got 65 marks out of 100 full
marks. Similarly, percentage solution is also expressed in 100 g solution. Thus, the
amount of solute present in 100 g of solution is called percentage by mass.
Percentage by mass (% w/w)
Mass of solute in gram
Mass of solution in gram
C HEMI S TRY
× 100
Optional Science - 10
0
141
For example: 30% sugar solution means, 30 g sugar is present in 100 g of the sugar
solution.
ii.
Percentage by volume (% w/v)
When the amount of dissolved solute is measured in gram (g) and the amount of solution
is measured in 100 ml, it is called percentage by volume.
Percentage by volume (% w/v) =
Mass of solute in gram
Volume of solution in ml
× 100
For example: 25% glucose solution means, 25 g glucose is present in 100 ml of the glucose
solution.
iii. Percentage by volume (% v/v)
When the amount of dissolved solute is measured in ml and prepared solution is
measured in 100 ml, it is called percentage by volume.
Percentage by volume (% v/v) =
Volume of solute in mL
Volume of solution in mL
×100
For example: 20% sulphuric acid solution means, 20 ml sulphuric acid is present in 100
ml of the solution.
2. Grams per litre
The gram mass of solute in one litre of solution is called grams per litre. In gram per litre,
the mass of solute is expressed in gram and the volume of solution is expressed in litre. It
is often used to describe the concentration of a solid in a solution. It is represented by g/l.
Gram per liter (g/ l) =
Gram per liter (g/ l) =
Mass of solute in gram
Volume of solution in litre
Mass of solute in gram
Volume of solution in m l
×1000
For example: 25 g/l calcium chloride means, 25 grams of calcium chloride is present in
one litre of solution(1000 m l of solution).
3. Molarity (M)
Molarity (M) is the number of moles of solute present in one litre of solution. i.e.,
Number of moles of solute
Molarity =
Volume of solution in liter
Molarity =
Number of moles of solute
Volume of solution in ml
×1000
We know that, the number of moles of any substance can be calculated dividing the
mass of solute by its molar mass.
0
142
Optional Science - 10
C HEMI S TRY
Example: 1
Calculate moles of methane in 64 g of methane.
Solution: Here, mass of methane = 64 g
Molar mass of methane = 16
Mass of methane 64
=
Moles of methane =
=4
14
Molar mass
Thus, the molarity of a substance can be calculated by using the following formula.
Molarity =
Mass of solute
Molar mass
×
1000
Volume of solution in ml
Molar solution
Sometimes only one mole of a solute is present in 1000 ml of solution or one litre of solution.
It is called molar solution. Thus, the solution containing one mole of solute in one litre of
solution is called molar solution. For example, if one mole of hydrochloric acid (36.5 gram) is
present in one litre of solution, it is called molar solution of hydrochloric acid.
Decimolar solution
If a solution contains 1/10 mole of a solute in one litre solution, then it is called decimolar
solution. For example, if 1/10 mole of nitric acid (6.3 gram) is present in one litre of solution, it
is called decimolar solution of nitric acid.
Activity
To prepare 1 molar solution of sodium chloride (NaCl)
•
Measure 58 g of NaCl crystals and keep into the one litre volumetric flask.
•
Add some water and stir it to make a homogeneous solution.
•
Fill water in the volumetric flask to make one litre.
•
It is now one molar (1 M) salt solution.
4. Molality
In some solution, we measure solute in mole and solvent in kg. It is called molatity.
Therefore, molality (m) is defined as the number of moles of solute present in one
kilogram of solvent.
Number of moles of solute
Molality =
Mass of solvent in kilogram
Molality =
Number of moles of solute
Mass of solvent in gram
×1000
The molality of the solution does not change with temperature. If 98 gram (1 mole) of
sulphuric acid is dissolved in 1000 gram of water, then it is called molal solution of
sulphuric acid.
C HEMI S TRY
Optional Science - 10
0
143
Molarity and Molality are completely different physical quantities. Molarity is measured
in mol/litre of solution while molality is measured in mol/kg of solvent.
Differences between molarity and molality
S.N.
Molarity
1.
S.N.
Molarity (M) is the number of moles of 1.
solute present in one litre of solution.
Molarity is measured in mol/litre of 2.
solution.
2.
Molality
Molality (m) is the number of moles of
solute present in one kilogram of solvent.
Molality is measured in mol/kg of solvent.
Memory Plus
For water as a solvent, molarity and molality have nearly same values. It is because 1 litre of
water nearly weighs 1 kg. But, for other solvents like CCl4, oil etc., the values are different.
Activity
To prepare 1 molal solution of sodium chloride (NaCl)
•
Take 58 g of NaCl in a beaker. It is molar mass of sodium chloride.
•
Keep exactly one kilogram of water in the beaker and stir to make solution.
•
Now, it is 1 molal solution of NaCl in water.
Example: 1
Calculate the molarity of 40g H2SO4 in 200 ml solution.
Solution:
Given, mass of solute = 40g
Volume of solution = 200 ml
We know that molar mass of H2SO4 = 98 g
Again, number of moles of H2SO4 =
Mass of solute
40g 40
=
=
Molecular weight of solute 98g 98
Also, volume of solution in litres =
200
1
=
1000 5
Now, Molarity (M) =
Example: 2
40/98 = 2.04 M
moles of solue
=
litres of solution
¹/₅
Calculate the molality if 90 g of NaCl is added into 1800 grams of water.
Solution:
Given, mass of solute = 90g
Mass of solvent = 1800 g
We know that molar mass of NaCl = 58 g (approx)
144
Optional Science - 10
C HEMI S TRY
Number of moles of NaCl =
Mass of solute
90g
=
Molecular weight of solute 58g
1800 9
=
1000 5
90/58 = 0.86M
Moles of solute
Now, Molality (M) =
=
Mass of solvent in kg ⁹/₅
Mass of solvent in kg =
5. Normality
The number of equivalents of a solute present in one litre of solution is called normality
(N). It means that normality is the number of mole equivalents in one litre of solution.
Number of equivalents of solute
Normality =
Volume of solution in litre
Normality =
Number of equivanents of solute
Volume of solution in mL
Mass of solute in gram
1000
×
Normality =
Volume
of
solution in ml
Equivalent mass
Normal solution (1 N)
The solution containing one equivalent of solute in one litre of solution is called normal
solution. For example, if 36.5 g of hydrochloric acid (one equivalent) is present in one litre
of solution, then it is called normal solution of HCl. Similarly, if 49 g of sulphuric acid (one
equivalent) is present in one litre of solution, then it is called normal solution of sulphuric acid.
Decinormal solution (N/10 )
The solution containing 1/10 equivalent of solute in one litre of solution is called decinormal
solution. For example, if 3.65 g of hydrochloric acid (N/10 equivalent) is present in one litre of
solution, then it is called decinormal solution of HCl. Similarly, if 4.9 g of sulphuric acid (N/10
equivalent) is present in one litre of solution, then it is called decinormal solution of sulphuric
acid.
Generally, we use normality for acids and bases. To calculate normality, we need to find out
the mole equivalent of the solution. The mole equivalent of an acid and a base can be calculated
by using the following formula.
Molar mass of acid
(Here, basicity means number of replaceable
Equivalent mass of acid =
Basicity
hydrogens)
For example:
i.
In HCl, there is one replaceable H+ ion. Therefore, basicity of HCl is 1.
ii.
In H2SO4, there are 2 replaceable H+ ions. Therefore, the basicity of H2SO4 is 2.
Molar mass of base
(Here, acidity means the number of
Equivalent mass of base =
Acidity
replaceable hydroxyl ions)
For example:
i.
In NaOH, there is one replaceable OH- ion. Therefore, acidity of NaOH is 1.
C HEMI S TRY
Optional Science - 10
0
145
ii.
In Al(OH)3, there are 3 replaceable OH- ions. Therefore acidity of Al(OH)3 is 3.
Similarly, to calculate equivalent weight of salt, the total charge in cation or anion is used
in place of acidity and basicity. For example, MgCl2 = Mg2+ + 2Cl- , in MgCl2, the total
charge in magnesium ion is 2. Hence, it is used to calculate equivalent weight.
In the solution, if molarity is given, the normality can be calculated by multiplying with
acidity of a base or basicity of an acid.
Normality = n × Molarity (where n is acidity or basicity)
Memory Plus
The normality of a solution is equal to its molarity, if acidity or basicity is one.
For example:
For an acidic solution,
a.
2 M of H2SO4 solution is the same as 4 N H2SO4 solution as its basicity is 2.
2 M of HNO3 solution is the same as 2 N HNO3 solution as its basicity is 1.
b.
For a basic solution,
4 M Ca(OH)2 solution is the same as 8 N Ca(OH)2 solution as its acidity is 2.
4 M NaOH solution is the same as 4 N NaOH solution as its acidity is 1.
Example: 1
Calculate the normality of the following.
a. 4 M of H2SO4
b.
12.5 g of calcium carbonate in 200 ml of solution
Solution:
a. Given, Molarity of the solution (M) = 4
n factor of H2SO4 = 2
As we know, Normality (N) = n × M = 2 x 4 =8
b.
Given, Mass of solute = 12.5 g
Molar mass of calcium carbonate = 100 g
"n" factor of calcium carbonate = 2
Solution = 200 ml
Equivalent mass of calcium carbonate =
Normality(N) =
Molar mass 100
=
= 50
"n" factor
2
Mass of solute in gram
Equivalent mass
12.5
1000
×
Normality (N) =
50
200
×
1000
Volume of solution in ml
Normality (N) = 1.25 N
146
Optional Science - 10
C HEMI S TRY
Answer writing skill
1.
I
What is Molecular mass? Illustrate with any two examples.
Ans: The sum of atomic mass of all atoms present in a molecule is called molecular mass.
For example, the molecular mass of methane (CH4) is 16 and molecular mass of calcium
carbonate (CaCO3) is 100.
2.
What is Avogadro’s number?
Ans: Avogadro’s Number is the number of atoms, molecules, ions or particles present in one
mole of a pure substance. It is equal to 6.022 × 1023.
3.
What are quantum numbers? Write down their names with symbol.
Ans: The characteristics of an electron and its position are determined by a set of specific
numbers called quantum number. There are four quantum numbers. They are:
i.
Principal quantum number (n)
ii.
Azimuthal quantum number(l)
iii. Magnetic quantum number (m)
iv. Spin quantum number (s)
4.
Define normality (N). At which condition the normality and molarity is equal?
Ans: The number of equivalents of a solute present in one litre of solution is called normality (N).
If "n" factor of a solution is one, then normality and molarity become equal. For example,
one molar solution of HCl, NaOH, NaCl, etc. have molarity and normality equal.
5.
Write down any two differences between atomic mass and molar mass.
S.N.
Atomic mass
S.N.
Molar mass
1.
The sum of mass of protons and 1.
The total mass of atoms present in a
neutrons is called atomic mass.
molecule is called molar mass.
2.
It depends upon number of protons 2.
It depends upon total number of
and neutrons present in the nucleus.
atoms present in the molecule.
Example: potassium = 39 amu
Example: sulphuric acid = 98 amu
6.
The molecular mass of nitrogen molecule is 28 amu. What does it mean?
Ans: The molecular mass of nitrogen molecule is 28 amu. It means that, the sum of atomic
mass of nitrogen molecule is 28 or it is 28 times heavier than ¹/₁₂th mass of carbon-12
isotope.
7.
Write a short note about principal quantum number.
Ans: The principal quantum number represents the main energy level or shell to which the
electrons belong to. It decides the size of the shell and the average distance of the shell
from the nucleus. The principal quantum number is denoted by the symbol "n". It has
non-zero values like 1, 2, 3, 4 or K, L, M, N. The maximum number of electrons present
in each principal quantum number is calculated by using 2n2 formula.
C HEMI S TRY
Optional Science - 10
0
147
8.
Calculate the molarity of 80 g H2SO4 in 400 ml solution.
Solution:
Given, mass of solute = 80g
Volume of solution = 400 ml
We know that molecular weight of H2SO4 = 98 g
Mass of solute
80g 80
Again, number of moles of H2SO4 = - - -= =
Molecular weight of solute 98g 98
Also, volume of solution in litres =
Now, Molarity (M) =
9.
400
2
=
1000 5
80/98 = 2.04 M
moles of solue
=
litres of solution
²/₅
Show the sub-shell electronic configuration of potassium and write down the quantum number for the last electron.
Ans: The sub-shell electronic configuration of potassium (K) is 1s2 , 2s2 2p6, 3s2 3p6, 4s1
Here, the last electron lies in 4s1
So, principal quantum number (n)= 4 (As the last electron lies in 4th shell)
Azimuthal quantum number (l) = 0 (As it has 's"sub-shell)
Magnetic quantum number (m)= 0 (For the value of "l"= 0 the value of "m" = 0))
Spin quantum number (s)= +1/2 (As the electron is in up spin)
10.
Write down all four quantum number for the eighth electron in the given
electronic configuration. (S) = 1s2 , 2s2 2p6, 3s2 3p4
Ans: Here, the eighth electron lies in 2p6
So, principal quantum number (n)= 2 (As the last electron lies in 2nd shell)
Azimuthal quantum number (l) = 1 (As it has 'p"sub-shell)
Magnetic quantum number (m)= -1 (because the 8th electron lies in px orbital)
Spin quantum number (s)= -1/2 (As the electron is in down spin)
0
148
Optional Science - 10
C HEMI S TRY
Exercise
JQ-
----• --------Step
1.
1
Define the following terms.
i.
Atomic mass
ii. amu
iii. Molecular mass
iv. One mole
v.
vi. Avogadro’s Number
Molar mass
2.
What is Quantum number? Write down their name.
3.
Write very short about
i.
Principal quantum number
ii.
Azimuthal quantum number
iii. Magnetic quantum number
iv. Spin quantum number
4.
Write down definition with formulae for the following:
i.
Percentage by mass ii. Percentage by volume
iii. Grams per litre
iv. Molarity
iv. Molality
v. Normality (N)
5.
What is molar solution.
6.
Define decimolar solution.
7.
What is molality (m)
8.
Define normal solution.
9.
Define decinormal solution.
C HEMI S TRY
Optional Science - 10
149
Step
2
1.
Write down any two characteristics of an atom.
2.
How many molecules are there in one mole of water?
3.
What information does principal quantum number give?
4.
Write down the relation of atoms, ions, molecules with Avogrado’s number.
5.
Give reason.
6.
i.
Inert gases are called monoatomic molecules. Why?
ii.
The molecular mass of oxygen molecule is 32 amu. What does it mean?
Differentiate between:
i.
Molarity and molality
ii.
Atomic mass and molar mass
iii. Normal solution and molar solution
Step
3
1.
Calculate molecular mass of calcium carbonate (CaCO3) and ammonium carbonate
(NH4)2CO3
2.
Calculate the molar mass of NaNO3 and find the number of molecules present in 2 mole
of NaNO3.
3.
Calculate the number of molecules present in 1 kg of water and 1 kg of carbon dioxide.
4.
Write down the value of quantum number for the last electron in the electronic configuration
2s1.
5.
What are the quantum numbers for the last electron of the chlorine atom?
6.
Calculate the molarity of 20 g of H2SO4 in 100 ml solution.
7.
Calculate the molality if 45 g of NaCl is added into 900 g of water.
8.
Calculate the normality in 2 M of H2SO4
9.
Calculate normality if 0.0345 g of sodium carbonate is present in 300 ml of solution.
10.
Calculate the number of molecules in 36 g water.
11.
What is the molality of a solution prepared by dissolving 5 g of toluene(C7H8) in 225
grams of Benzene (C6H6)?
12.
Calculate the molarity of 40 g H2SO4 in 100 ml solution.
13.
Calculate the molality if 90 g of NaCl is added into 450 g of water.
14.
Calculate the normality of a 4.0 molar sulphuric acid solution.
0
150
Optional Science - 10
C HEMI S TRY
4
Step
1.
Describe the mole concept.
2.
What are quantum numbers? Write very short about all quantum numbers.
3.
Describe about the principal quantum number.
4.
What is azimuthal quantum number? Describe the information obtained from the
azimuthal quantum number.
5.
Describe the information which are obtained from the magnetic quantum number.
6.
Explain in short about the spin quantum number.
Multiple choice questions
1.
What is the use of amu?
a)
To measure the length of very small distance
b)
To measure the time of very small duration
c)
To measure the mass of very small particles
d) To observe the very small particles
2.
3.
Which of the following is a Avogadro’s number?
a) 6.022 × 1023 atoms
b)
c)
d) All of above a, b and c
6.022 × 1023 ions
How many quantum numbers are there?
a) 1
4.
6.
3
d) 4
b) l
c)
m
d) s
a)
Principal quantum number b) Azimuthal quantum number
c)
Magnetic quantum number d)Spin quantum number
What is the value of “l” for n=1
b) 2
c)
1
d) 0
c)
3
d) 4
What is the normality for one molar HCl?
a) 1
8.
c)
Which quantum number explains the orientation of the orbitals?
a) 3
7.
b) 2
Which symbol is used to denote principal quantum number?
a) n
5.
6.022 × 1023 molecules
b) 2
What does it mean by N/10?
a)
Decimolar solution
b) Decinormal solution
c)
Normal solution
d) Molar solution
***
C HEMI S TRY
Optional Science - 10
0
151
UNIT
8
PERIODIC
TABLE AND
PERIODIC LAWS
..............,......................,...... ...................................................
About the inspiring personality
Wolfgang Pauli born in 25 April 1900 AD in Vienna, Austria and died in 15 December
1958 AD in Switz. Pauli propounded the Pauli Exclusion Principle. For this great work he
was awarded with a Nobel Prize in 1945 AD. Pauli along with Neils Bohr also formulated
the Aufbau principle. Not only this, Pauli also made a major contribution in the quantum
mechanics.
Syllabus issued by CDC
•
•
•
•
•
•
•
Mendeleev's and Modern periodic
Table (s, p, d and f concept)
Application of periodic table
Aufbau principle
Electronic configuration
Valency and variable valency
Periodic variation
Atomic
size,
Ionization
potential, Electron affinity and
Electronegativity
Learning objectives:
After completing the study of this unit, students
will be able to:
• Show the electronic configuration based on s,
p, d and f.
• Introduce s-block, p-block, d-block and f-block
elements along with their characteristics.
• Define valency, variable valency, and radical.
• Explain
variation
of
atomic
size,
ionization potential, electron affinity and
electronegativity in the period and group.
Key terms and terminologies of the unit
1.
Classification of elements: The grouping of elements according to their similarities
and differences is called the classification of elements.
Mendeleev's periodic law: According to Mendeleev's periodic law, the physical
and the chemical properties of elements are the periodic functions of their atomic
weights.
Mendeleev's periodic table: The table or chart which is obtained after arranging
elements on the basis of increasing atomic weight is called Mendeleev's periodic table.
Modern periodic law: According to Modern periodic law, the physical and the
chemical properties of elements are the periodic functions of their atomic numbers.
2.
3.
4.
152
Optional Science - 10
C HEMI S TRY
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
24.
25.
26.
27.
Modern periodic table: The table or the chart which is obtained after arranging
elements on the basis of their increasing atomic numbers is called the modern
periodic table.
Periods: The horizontal rows of the periodic table are called periods. In periods,
elements with gradual change in characters and atomic numbers are kept.
Groups: Vertical columns of the periodic table where elements with similar
characteristics are kept are called groups.
Periodic variation: The variation in the properties of elements across a period or down
the group of the modern periodic table in a periodic manner is called periodic variation.
Atomic size: The distance between nucleus and the outermost shell of an isolated
gaseous atom is called atomic size.
Ionization potential: The amount of energy required to remove the loosely bonded
outermost electron from an isolated gaseous atom is called ionization potential.
Valence electrons: The total numbers of electrons present in the outermost shell of
an atom are called valence electrons.
Valency: The total number of electrons gained or lost or shared during the chemical
combination is called valency.
Electron affinity: The amount of energy released by an atom when an electron is
added to its valence shell is called electron affinity.
Electronegativity: The amount of energy required for an atom to attract foreign
electrons towards itself is called electronegativity.
Aufbau principle: According to Aufbau principle, “filling of electrons in the subshells always occurs from the lower energy level to the higher energy level.”
Electronic configuration: The systematic distribution of electrons in different shells
and sub-shells is called electronic configuration.
s-block: The block of alkali metals (IA) and alkaline earth metals (IIA) which is
present at the left-hand side of the periodic table is called s-block.
s-block elements: The elements which have the last electron in "s" sub-shell are
called s-block elements.
p-block: The block of metals, non-metals, metalloids and inert gases which are
present in IIIA, IVA, VA, VIA, VIIA and zero groups is called p-block.
p-block elements: The elements which have the last electron in "p" sub-shell are
called p-block elements.
d-block: The block of transitional metals which is present in between s-block and
p-block of the modern periodic table is called d-block.
d-block elements: The elements which have the last electron in d-sub shell are
called d-block elements.
f-block: The block of lanthanides and actinides which is present separately below
the main periodic table is called f-block.
Valence shell: The outermost shell of an atom is called valence shell.
Valence electrons: The total number of electrons present in the valence shell of an
atom are called valence electrons.
Valency: The number of electrons gained, lost or shared by an element during the
chemical reaction is called valency.
Variable valency: More than one valency of an element is called variable valency.
C HEMI S TRY
Optional Science - 10
0
153
Introduction
In the initial stage of the study of science, very few elements were known to us. These elements
could be studied individually. With the rapid development of scientific research, more and
more new elements with their different physical and chemical properties are discovered. Till
now, about one hundred eighteen elements with different atomic masses and numbers are
known to us. So, it is quite difficult to study these elements separately. To solve this problem,
chemists realized that elements with similar and dissimilar properties should be divided into
different groups. So, classification of elements refers to the process of grouping of elements on
the basis of their similarities and dissimilarities. The grouping of elements according to their
similarities and differences is called the classification of elements.
Classification is a scientific process. It makes the study of elements easy, fast and clear. At
the beginning of the classification, elements were divided into three groups on the basis of
their physical states like solid, liquid and gas. After physical state, elements were classified
according to the metallic characters such as metals, non-metals and metalloids. In the field
of classification, Antony Lavoisier was the first chemist, who studied elements on the basis
of their metallic nature and categorized them into two groups, i.e. metals and non-metals. At
that time, chemists knew only thirty-two elements. Lavoisier's classification could not last
long, as some elements having both the characters of metal and non-metal were discovered
later. There is no doubt that different chemists have continuously tried to classify elements
systematically for the better and advanced study of elements.
Mendeleev's Period Law
Russian chemist Dmitri Mendeleev followed the idea which was given by John Newland in
1864 AD. At this time, about 63 elements were discovered. Mendeleev studied the physical and
chemical properties of these elements along with their compounds. After the complete study
of these elements, he made a sequence of elements in an ascending order of atomic weights.
similar to the sequence which was given by John Newland in 1864 AD. In this sequence, he
found that the elements with similar properties occur at a regular interval. This observation
led Mendeleev to conclude a law, which is called Mendeleev periodic law.
According to Mendeleev's periodic law, the physical and the chemical properties of elements
are the periodic functions of their atomic weights. It means that when elements are arranged
on the basis of increasing atomic weights, the elements having similar physical and chemical
properties are repeated after a regular interval.
Memory Plus
The meaning of periodic function is that the properties of elements go on changing when
atomic mass is increased but after a certain regular interval; they repeat the characters of
the previous element.
Mendeleev's Periodic Table
After the study of physical and chemical properties of elements, Mendeleev proposed a
periodic table called Mendeleev’s periodic table. The table or chart which is obtained after
arranging elements on the basis of increasing atomic weight is called Mendeleev's periodic
table.
154
Optional Science - 10
C HEMI S TRY
In Mendeleev's periodic table, there are seven horizontal rows called periods, and eight vertical
columns called groups. Sometimes periods are also called series and groups are also called
families. In this table, elements with similar physical and chemical properties fall under the
groups and elements with gradual change in characteristics fall under the periods. During the
time of Mendeleev, only 63 elements were known to us, so he left some gaps for undiscovered
elements. For example, scandium, gallium, germanium, etc. were discovered after the design
of Mendeleev's periodic table. To keep these elements, Mendeleev left gaps by saying ekaboron, eka-aluminium and eka-silicon.
A part of Mendeleev's periodic table is given below:
Group I
Group II
Group III
Group IV
Group V
Group VI
Li
Be
B
C
N
O
F
Na
Mg
Al
Si
P
S
Cl
Period
1
H
Period
2
Period
3
Period K
4
Period Rb
5
Period Cs
6
*
Ca
Cu
1
Zn
Sr
Ag
2
Y
Cd
Ba
Au
Ti
*
3*
Zr
In
La
Hg
V
As
Nb
Sn
Hf
Th
Cr
Sb
Pb
Fe
Co
4*
Br Ni
Ru
Rh
Te
W
Bi
Mn
Se
Mo
Ta
Group VII Group VIII
l
Os
Re
Po
At
Pd
lr
Pt
Name given by Mendeleev: 1* Eka - Aluminium,
2* Eka - Boron, 3* Eka - Silicon, 4* Eka - Manganese
Characteristics of the Mendeleev's Periodic Table
1.
Mendeleev arranged elements on the basis of increasing atomic weight.
2.
In this table, there are seven horizontal rows (periods) and eight vertical columns (groups).
3.
In Mendeleev's periodic table, he left gaps for undiscovered elements. For example;
scandium, gallium, germanium, etc.
4.
Each group of Mendeleev's periodic table was further divided into two sub- groups (subgroup A and sub-group B).
5.
Inert gases like He, Ne, Ar, Kr, Xe and Rn were not discovered at the time of Mendeleev,
so there was no separate place for them.
Merits or Advantages of Mendeleev's Periodic Table
1.
Mendeleev's periodic table was the first scientific as well as systematic classification of
elements, which made their study easy, fast and systematic.
2.
Many elements were not discovered during the time of Mendeleev. So he left gaps for
these elements. For example, scandium, gallium and germanium were discovered later on.
3.
The atomic weight of some elements like beryllium, platinum, gold, uranium, etc. was
not confirmed before Mendeleev's periodic table came into existence. With the help of
this table, atomic masses of these elements were corrected.
C HEMI S TRY
Optional Science - 10
0
155
4.
Mendeleev's periodic table encouraged subsequent scientists to discover new elements as
he left some gaps for them.
Demerits of Mendeleev's Periodic Table
1.
In Mendeleev's periodic table, he could not arrange hydrogen properly because sometimes
it gains electrons like those of halogens (group VIIA) and sometimes it loses electrons
like those of alkali metals (group IA).
2.
Mendeleev could not arrange isotopes properly as they have the same atomic numbers
but different atomic weight.
Memory Plus
According to the Mendeleev, isotopes of one element should have different places as
they have different atomic weight. For example; there are three isotopes of carbon,
such as C612, C613, and C614. On the basis of Mendeleev's periodic table, there should
be three different places for them as they have different weight.
3.
In some cases of Mendeleev’s periodic table, elements with more atomic weight were
placed first than those with less atomic weight. It was completely wrong according to his
periodic law. For example: cobalt with atomic weight 58.9 was placed before nickel with
atomic weight 58.6.
4.
In some places of Mendeleev's periodic table, chemically dissimilar elements were
grouped together. For example; very less reactive coinage metals (Cu, Ag, and Au) and
highly reactive alkali metals (Li, Na, K, Rb and Cs) were placed in the same group (first
group).
5.
In Mendeleev's periodic table, chemically similar elements were placed in different
groups. For example; gold is similar to platinum, copper is similar to mercury, barium is
similar to lead, etc. Unfortunately they were placed separately.
6.
Mendeleev could not arrange lanthanides and actinides properly in the fixed position.
7.
Mendeleev's periodic table was unable to explain the atomic properties of the elements
like valency, metallic characters, ionization potential, electronegativity, reactivity, etc.
8.
All groups are divided into sub-groups but the 8th group is not divided into sub-groups.
Modern Periodic Law
To overcome the defects of Mendeleev's periodic table, a group of chemists led by Henery
Moseley studied the physical and chemical properties of elements in 1913 AD with the help of
x-ray spectra. They concluded that atomic number is more fundamental property of elements
rather than their atomic weight. This conclusion was quite satisfactory for an atom because
chemical properties of the elements depend upon the number of electrons present in its atom.
With the help of the above study, Henery Moseley modified the Mendeleev's periodic law.
This modified law is called modern periodic law.
According to Modern periodic law, the physical and the chemical properties of elements are the
periodic functions of their atomic numbers. It means that when elements are arranged on the basis
of their increasing atomic number, at a regular interval, the properties of elements are repeated.
156
Optional Science - 10
C HEMI S TRY
While making the sequence of elements based on their increasing atomic number, it is found
that the elements which have similar physical and chemical properties lie in the same vertical
column. Similarly, the elements with gradual change in properties lie in the same horizontal
row one after another.
Modern Periodic Table
After complete study of the physical and chemical properties of elements and their compounds,
the team of Henery Moseley proposed the modern periodic law, which is modified form of the
Mendeleev's periodic law. With the help of this modern periodic law, Bohr arranged elements
on the basis of increasing atomic numbers. As a result, he found a table called the modern
periodic table.
The table or the chart which is obtained after arranging elements on the basis of their
increasing atomic numbers is called the modern periodic table. In the modern periodic table,
there are seven horizontal rows called periods. In these periods, elements with gradual change
in characters lie one after another. Similarly, in modern periodic table, there are 18 groups. In
these groups, elements with similar physical and chemical properties fall one below another.
Characteristics of the Modern Periodic Table
The main features of the modern periodic table are given below:
1.
In modern periodic table, elements are arranged on the basis of their increasing atomic
numbers.
2.
In this table, there are seven periods and 18 groups.
3.
Hydrogen is kept in the first period and the first group.
4.
Inert gases like He, Ne, Ar, Kr, Xe and Rn are placed in a separate group (zero group or
18th group) at the extreme right side of the table.
5.
In the modern periodic table, metals are kept at the left-hand side, non-metals at the
right-hand side and metalloids are placed between metals and non-metals.
6.
In this table, hydrogen is placed in 1st( IA) group and lanthanides and actinides are placed
in a separate box below the main table.
7.
Reactive metals, less reactive metals, transitional metals, reactive non-metals and lessreactive non-metals are kept separately. But, metalloids are not perfectly grouped. They
are roughly scattered in the right side of the periodic table.
8.
The whole periodic table is based on atomic sub-shells and divided into four blocks. They
are s-block, p-block, d-block and f-block.
9.
Most of the synthetic elements that are prepared in the laboratory are generally present
in the last periods (6th and 7th).
Memory Plus
In modern Periodic Table, the s-block elements are kept on the extreme left, p-block
elements are on the extreme right, d-block elements are placed between s-block and
p-block and f-block elements are kept separately below the main table.
C HEMI S TRY
Optional Science - 10
0
157
Advantages of the Modern Periodic Table
In the modern periodic table, elements are classified on the basis of increasing atomic numbers.
This system of classification helps to solve the defects of Mendeleev's periodic table in the
following ways.
1. The position of hydrogen is fixed: The accurate position of hydrogen has not yet been
solved completely. But as its atomic number is the least number (i.e. one), it is kept in IA
(group 1) group of the modern periodic table along with alkali metals.
2.
The position of isotopes is fixed: Isotopes are the atoms of the same elements, which
have the same atomic numbers but different atomic weights. Therefore, isotopes of one
element are placed together in the same group. For example, there are three isotopes of
carbon (i.e. C612, C613 and C614) which have same atomic numbers. They are placed together
in IVA group of the modern periodic table.
3.
The wrong position of the elements has been corrected: When elements are arranged
on the basis of their increasing atomic numbers, the wrong position of argon, potassium,
nickel, cobalt, etc. is solved automatically without changing their own places.
4.
The alkali metals and coinage metals are kept separately: In the modern periodic table,
the most reactive alkali metals are kept in IA group (group 1) whereas the least reactive
coinage metals are kept in IB group (group 11).
5.
Lanthanides and actinides are kept below the main table: In the modern periodic table,
fourteen elements of lanthanide series and fourteen elements of actinide series are placed
in a separate box below the main periodic table.
6.
The elements are arranged according to the electronic configuration of their orbitals,
viz. s, p, d and f. This divides the periodic table into four main blocks, i.e. s, p, d and f
block.
Why hydrogen can be placed in group IA along with alkali metals
i.
Both hydrogen and alkali metals have one valence electron.
ii.
Both hydrogen and alkali metals can lose one electron to form electropositive radicals.
iii. Both hydrogen and alkali metals can form halides, oxides, sulphides, etc.
iv. Both hydrogen and alkali metals can react with halogens, oxygen and sulphur.
Why hydrogen can be placed in group VIIA along with halogens
i.
Both hydrogen and halogens have valency one.
ii.
Both hydrogen and halogens can gain one electron to form electronegative radicals.
iii. Both hydrogen and halogens need one electron to complete their stable electronic
configuration.
iv. Both hydrogen and halogens can react with metals.
v.
Both hydrogen and halogens can make diatomic molecules.
vi. Both hydrogen and halogens occur in gaseous state.
Drawbacks of the modern periodic table
The modern periodic table has corrected many mistakes of the Mendeleev’s periodic table,
still it has some drawbacks. Some weaknesses of the modern periodic table are as follows:
0
158
Optional Science - 10
C HEMI S TRY
1.
The position of hydrogen is still controversial as it can be placed both in group IA group
(group 1) and VIIA (group 17).
2.
The lanthanides and actinides do not have a clear group. But their position is still separate
from the rest of the elements.
3.
In modern periodic table, helium is kept in p-block but its last electron falls into the
s-orbital.
Position of Elements in Modern Periodic Table
1.
Position of hydrogen: Hydrogen has only one shell with one electron. Due to its one
atomic number, it is placed under IA group of the modern periodic table along with alkali
metals. But, hydrogen shows both the characteristics of alkali metals and halogens.
2.
Position of metals, non-metals and metalloids: In the modern periodic table, metals are
present at left-hand side, non-metals are present at right-hand side and metalloids are
placed between metals and non-metals.
3.
Position of lanthanides and actinides: A group of fourteen elements starting from
cerium (Ce58) to lutetium (Lu71), which have similar characters with lanthanum (La57) are
called lanthanides. Similarly, a group of fourteen elements starting from thorium (Th90) to
lawrencium (Lr103), which have similar characters of actinium (Ac89) are called actinides.
These twenty eight elements (14 lanthanides and 14 actinides) are kept separately in the
separate box below the main periodic table. These elements have dissimilar characters
with other elements of the rest of the periodic table.
4.
Position of inert gases: He, Ne, Ar, Kr, Xe and Rn are called inert gases as they do not
participate in chemical reactions. These elements have zero valency. They are kept in the
zero group (group 18) at the extreme right-hand side of the modern periodic table.
Differences between Modern and Mendeleev’s Periodic Table
Modern Periodic Table
Mendeleev’s Periodic Table
1.
Modern periodic table is based on
increasing atomic number.
1.
Mendeleev’s periodic table is based on
increasing atomic weight.
2.
In this table, there are seven periods
and eighteen groups.
2.
In this table, there are seven periods
and eight groups.
3.
In this table, hydrogen, isotopes
lanthanides and actinides are kept
properly.
3.
In this table, hydrogen,isotopes
lanthanides and actinides are not kept
properly.
Memory Plus
Alkaline earth metals: Elements which are present in IIA group of the modern periodic
table are called alkaline earth metals. They are found on the earth’s crust and react with
water to give hydroxides. They include magnesium (Mg), calcium (Ca), etc.
Mg + 2H2O → Mg(OH)2 + H2
Ca + 2H2O → Ca(OH)2 + H2
C HEMI S TRY
Optional Science - 10
0
159
Importance of the Periodic Table
Periodic table is very important to make the study of elements easy, fast and systematic. It
is a useful tool for the students, chemists and scientists. The modern periodic table not only
mentions the name, atomic number and position of the elements but also their atomic weights,
electronic configuration, nature, isotopes and other characteristics. Thus, periodic table is very
useful to us. Some of the important points are listed below.
i.
The complete information about the elements like the number of electrons, number of
protons, electronic configuration, atomic number, atomic weight, valency, nature, block,
etc. can be obtained from the periodic table.
ii.
We can study the properties of elements with the help of the periodic table, .
iii. The periodic variations such as atomic number, valency, atomic radius, ionization
potential, electronegativity, electron affinity, etc. can be studied easily with the help of
periodic table.
iv. The characteristics of the elements can be known by knowing the exact position of the
element in the periodic table.
v.
The properties of the elements that are not yet discovered can also be predicted.
vi. The periodic table makes the arrangement of elements systematic, scientific and clear.
Memory Plus
The widely accepted modern periodic table is also called long form of periodic table. It is
given by IUPAC.
Periods and Groups of Modern Periodic Table
Periods
In the modern periodic table, there are seven horizontal rows called periods. In each
period, there are fixed numbers of elements with gradual change in atomic numbers and
characteristics. As we move from left to right in the period, the size of atoms decreases but the
atomic number increases. Thus, the horizontal rows of the periodic table are called periods. In
periods, elements with gradual change in characters and atomic numbers are kept. The very
short description of the different periods is given in the table.
S.N.
1.
2.
3.
4.
5.
6.
7.
Period
First
Second
Third
Fourth
Fifth
Sixth
Seventh
Number of Elements
2
8
8
18
18
32
26
Types of Period
Very short period
Short period
Short period
Long period
Long Period
Very long period
Very long but incomplete period
Groups
The vertical columns of the periodic table are called groups. There are a total 18 groups in
the modern periodic table. In these groups, elements with similar characteristics fall one
below another. Thus, vertical columns of the periodic table where elements with similar
characteristics are kept are called groups.
160
Optional Science - 10
C HEMI S TRY
Except zero and VIII groups, all other groups are further divided into sub-groups A and B. In
the eighth group, there are three vertical columns but they are not represented by A, B and C.
Altogether, there are a total of eighteen vertical columns, which are also called 18 groups in
the long form of the modern periodic table.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
IA
IIA
IIIB
IVB
VB
VIB
VIIB
VIII
VIII
VIII
IB
IIB
IIIA
IVA
VA
VIA
VIIA
0
Fact with reason
Sodium and potassium are kept in the same group. Why?
Sodium and potassium have the same number of valence electron and valency. They also
form the similar type of radical. So they are kept in the same group.
~
Differences between Periods and Groups
Periods
'
Groups
1.
The horizontal rows of the periodic
table are called periods.
2.
There are a total of seven periods in the
modern periodic table.
I
-
3.
In the period left to right, the atomic
L___J size decreases.
1.
The vertical columns of the periodic
I table are called groups.
2.
There are a total of nine groups in
modern periodic table.
I
I
3.
1
I
In the group top to bottom, the
atomic
size increases.
I
-
__J
Periodic Variation
In the modern periodic table, there are seven horizontal rows and 18 vertical columns.
Horizontal rows are called periods and vertical columns are called groups. The elements
present in a group are similar to each other in many aspects such as valence electrons, valency,
metallic nature, radical formation, etc. Similarly, the elements across a period also have some
similarities such as valence shells. Not only similarities, elements present in the same group
and same period also have many differences. In a group, elements have different atomic
size, ionization potential, electronegativity, etc. The variation in the properties of elements
in periods and groups are periodic. It means that characteristics repeat at a regular interval.
Thus, the variation in the properties of elements across a period or down the group of the
modern periodic table in a periodic manner is called periodic variation.
Memory Plus
Alkali metals: Elements which are present in IA group of the modern periodic table are
called alkali metals. Examples: lithium (Li), sodium (Na), potassium (K), etc. These metals
react with water to give hydroxides.
2Na + 2H2O → 2NaOH + H2
2K + 2H2O → 2KOH + H2
C HEMI S TRY
Optional Science - 10
0
161
Periodic variation of the some properties
1.
Atomic size: The distance between nucleus and the outermost shell of an isolated gaseous
atom is called atomic size. As we go from top to bottom in a group, the atomic size
increases as the number of additional shell increases. Similarly, as we go from left to right
in group, the atomic size decreases as nuclear force of attraction increases.
..
Atomic Radius Decreases
Oroup
IA 2A
(I)
3A 4A SA 6A 7A 8A
(13) (1 4) ( 15)(16) {17) {18)
(2)
Q
G
H
He
2 ~
Li
Be
5
fig:Variation of atomic size in a group and period of the modern periodic table
Fact with reason
Atomic size increases in a group and decreases in a period. Why?
The number of additional shell increases in a group as we go from top to bottom.
So, atomic size increases in a group. However, in a period, the numbers of shells are
fixed but the number of protons increases as we go from left to right. The additional
proton increases the nuclear force of attraction and decreases the atomic size.
2.
Ionization potential (or Nuclear power)
The amount of energy required to
remove the loosely bonded outermost
lncr~
gY,
I
electron from an isolated gaseous
I ® \
H,
•H
' '_, I
...
atom is called ionization potential.
• u ~'
■ C NO F N,
•i
Ionization potential is measured in
eK
I I
electron volt (eV). Its value is more in
@
I I
,
)
I I
the small size and less in the big size.
____ ,,,,, I
Therefore, in the period left to right,
fig:variation of ionization energy in periodic table
ionization potential increases as the
atomic size decreases. Similarly, the value of ionization potential decreases in the group
top to bottom, as atomic size increases.
~
t~
·
·
·
-~
••
162
Optional Science - 10
C HEMI S TRY
--7
Fact with reason
Why does ionization potential increase in the period left to right and decrease
top to bottom in the group?
In the period left to right, the atomic size decreases and nuclear force of attraction
increases. It makes difficult to remove outermost electron from the atom. So, the
ionization potential increases in the period left to right. Similarly, in the group,
atomic size increases. It makes easy to remove the outermost electron from the
atom. So, the ionization potential decreases top to bottom in the group.
3.
Electron affinity
The amount of energy released by an
atom when an electron is added to its
valence shell is called electron affinity.
Conceptually, electron affinity is opposite
to the ionization potential. When an
electron is added to the valence shell of
a neutral atom, the atom releases energy.
Therefore, the electron affinity is the
measurement of the electron pulling
fig:variation of electron affinity in periodic table
ability of an atom. Higher the value of
electron affinity, higher will be the ability to pull an electron and vice-versa. Its unit is
eV. Electron affinity increases in the period left to right because atomic size decreases.
Similarly, electron affinity decreases in the group top to bottom because atomic size
increases.
Fact with reason
Why does electron affinity increase in the period left to right and decrease top to
bottom in the group?
In the period left to right, the atomic size decreases and nuclear force of attraction
increases. It makes easy to pull an electron towards the atom. So, the electron affinity
increases in the period left to right. Similarly, in the group, atomic size increases and
nuclear force of attraction decreases. It makes difficulty to pull an electron towards
the atom. So, electron affinity decreases top to bottom in the group.
4.
Valence electrons
2
Number of Valence Electrons
3 4
The total numbers of electrons present in the
outer most shell of an atom are called valence
electrons. It increases in period left to right and
remains the same in the group top to bottom.
5.
fig:variation of valence electrons in periodic table
Valency
The total number of electrons gained or lost or shared during the chemical combination
is called valency. In a period left to right, valency first increases up to four and then
decreases up to zero. Similarly, in the group top to bottom, it remains the same.
C HEMI S TRY
Optional Science - 10
0
163
For example:
6.
Element:
Li
Be
B
C
N
O
F
Ne
Valency
1
2
3
4
3
2
1
0
Electronegativity
The amount of energy required for an atom to attract foreign electrons towards itself is
called electronegativity. It increases as the atomic size decreases and it decreases as the
atomic size increasing. In period left to right, electronegativity increases because atomic
size decreases and nuclear force of attraction increases. Similarly, in group top to bottom
electronegativity decreases because atomic size increases and nuclear force of attraction
decreases.
l&WIIHll4¥1@111119.
fig:variation of electronegativity in periodic table
Fact with reason
Electronegativity increases in the period left to right and decreases in the group
top to bottom. Why?
In the period left to right, the atomic size decreases and nuclear force of attraction
increases. It makes easy to attract the foreign electron towards the atom. So, the
electronegativity increases in the period left to right. Similarly, in the group, atomic
size increases and nuclear force of attraction decreases. It makes difficulty to attract
the foreign electron towards the atom. So, the ionization potential decreases top to
bottom in the group.
7.
Metallic characters: Metallic character increases from top to bottom in the group and
decreases from left to right in the period.
Metallic character decreases
□ M"'b
T
</l
-;-
~
"'u~
.s
...
.2l
u
:il"'
-6
s
u
2
--.
Be
11 12
Na Mg
i·
. •
Me<allolds
□
□ Nonmetob
.
F
Ne
13
16
17
II
Az
15
6
11
Al
29
31
,.
SI
15
p
16
17
9
s a
He
10
,.u
' 8 9 10,.
K Ca Sc n
V Cr
" ~ Fe CoZ1 Ni Cu Zn Ga c'e :. ~ Br ~
., ,. y
., .,
"' A Te I Xe
Rb Sr
" Tc Ru Rh Pd Ag Cd In Sn
" Zr Nb Mo
,.
,, ,. ,.
,. ,. .,
Ca Ba La
" Hf Ta w Re Os Ir Pt Au Hg TI Pb Bi Po" Al Rn
.,
20
19
3
21
..
.. ..
72
56
Fr
Ra
Ac
22
IOI
5
z,
105
Rf Db
106
5g
26
.. .. .. ..
107
76
77
IOI
109
Bh Ha Mt
47
II
110
111
35
.. ..
112
12
116
-
~
~
~
a
Lanthoruda Ce
Pr
Nd Pm Sm Eu Gd Tb Dy
~
61
~
~
"
M
"
Ho
Er
Tm Yb
~
~
Lu
~
~
n
"
H
"
~
~
~
W
~
~
~
W
Adlnlda Th
~
..
.. ..
13
114
.5
Pa
U
Np
Pu Am Cm
Bk
Cf
Q
Es
fig:variation of metallic characters in periodic table
164
18
--,
"B• C N' 0
14
Optional Science - 10
C HEMI S TRY
Fm Md No
~
Lr
Sub-Shells (or Orbitals)
On the basis of 2n2 formula, when there are two electrons in the outermost shell of an atom,
it is called duplet (for example helium). Similarly, when there are eight electrons in the
outermost shell, it is called octet such as Ne, Ar, Kr, Xe and Rn. The electronic configuration
of all the elements cannot be explained by the 2n2 formula. Thus, the concept of sub-shells
was proposed. According to this concept, each and every main shell contains one or more
sub-shells, which are denoted by s, p, d and f. Different shells contain different numbers of
sub-shells. Thus, the shells which are present within the main shell are called sub-shell. They
are also called sub-energy level or orbitals and denoted by s, p, d and f. The shells with their
sub-shells are given in the table.
Main Shell
Main shell first
Total sub-shells
Sub-shells (or Orbitals)
(n=1)
1
s
Main shell second (n=2)
2
s and p
Main shell third
(n=3)
3
s, p and d
Main shell fourth (n=4)
4
s, p, d and f
The s- sub-shell may contain maximum two electrons.
The p- sub-shell may contain maximum six electrons.
The d- sub-shell may contain maximum ten electrons.
The f- sub-shell may contain maximum fourteen electrons.
On the basis of the above data, we can co-relate the 2n2 formula with sub-shells(s, p, d and
f). The main shell, its sub-shells and the maximum numbers of electrons present there can be
summarized as follows:
Main shell
Sub-shells
Total electrons
K (n = 1)
1s
2
L (n = 2)
2s, 2p
2+6=8
M (n = 3)
3s, 3p, 3d
2 + 6 + 10 = 18
N (n = 4)
4s, 4p, 4d, 4f
2 + 6 + 10 + 14 = 32
Aufbau Principle
The Aufbau is a German word. It means “building up or construction”. This concept was
formulated by the scientists Niels Bohr and Wolfgang Pauli. According to the concept of the
sub-shell, each and every main shell contains one or more sub-shells, which are represented
by s, p, d and f. There is difference in the energy level of these sub-shells. During electronic
configuration, entering of electrons always occur from the lower energy level to the higher
energy level. Thus, according to Aufbau principle, “filling of electrons in the sub-shells always
occurs from the lower energy level to the higher energy level.”
In absence of magnetic field, the energy of an orbital depends upon the value of principal
quantum number (n) and azimuthal quantum number (l). Hence, the sequence of filling of
orbitals can be obtained from the (n+I) rule. It can be summarized as:
C HEMI S TRY
Optional Science - 10
0
165
i.
The orbitals with lower value of (n+l) have lower energy and are filled first.
ii.
When two orbitals have the same value of (n+l), the orbital with lower value of "n" has
lower energy and is filled first.
Memory Plus
For the sub-shells s, p, d and f, the value of azimuthal quantum number (l) is represented
as 0, 1, 2 and 3 respectively. For example: in 3d, the value of n = 3 and the value of "l" is 2.
The (n+l) value of the some orbitals is given in the table
Orbitals
Principal quantum number (n)
Azimuthal
quantum number (l )
Sum of n + l
1s
1
0
1+0=1
2s
2
0
2+0=2
2p
2
1
2+1=3
3s
3
0
3+0=3
3p
3
1
3+1=4
3d
3
2
3+2=5
4s
4
0
4+0=4
From the above table, we can conclude the following points.
1.
The first electron always goes to the 1s orbital as it has the
lowest (n+l) value.
2.
In between 2s and 2p, the (n+l) value of 2s is less than 2p. So,
the 2s orbital is filled first.
3.
In between 2p and 3s, both have the same value of (n+l). In this
case electron enters into 2p orbital which has less value of "n".
4.
In between 3s and 3p, the (n+l) value of 3s is less than 3p. So,
the 3s orbital is filled first.
5.
In between 3d and 4s, the (n+l) value of 4s is less than 3d. So,
the 4s orbital is filled first.
On the basis of above discussion, the sequence of filling of electrons
in different sub-shells is as follows.
l=O 1=1
1=2
1=3
n=1
n=2
n=3
n=4
n=S
n=6
n=7
n=8
fig:Order of filling electrons in
orbitals
1s< 2s< 2p< 3s< 3p< 4s< 3d< 4p< 5s< 4d< 5p< 6s< 4f < 5d < 6p < 7s……..
To find out the sequence of energy level of different sub-shells, an alternative arrow diagram
method is shown in the given figure above.
Limitations to Aufbau principle
The Aufbau principle is applicable in most of the cases. However, some elements do not follow
this rule. For example: copper and chromium do not follow Aufbau principle.
166
Optional Science - 10
C HEMI S TRY
According to Aufbau Principle: Chromium (24) = 1s2, 2s2 2p6, 3s2 3p6, 4s2, 3d4
Actual electronic configuration: Chromium (24) = 1s2, 2s2 2p6, 3s2 3p6, 4s1, 3d5
According to Aufbau Principle: Copper (29) = 1s2, 2s2 2p6, 3s2 3p6, 4s2, 3d9
Actual electronic configuration: Copper (29) = 1s2, 2s2 2p6, 3s2 3p6, 4s1, 3d10
Electronic Configuration
The electronic configuration in different shells is done according to 2n2 formula. According
to this formula, in the first shell, we can fill maximum 2 electrons, in second shell, we can fill
8 electrons and in the third shell 18 electrons. This method is easy and clear for the first 18
elements. But, beyond atomic number 18, it does not express the true electronic configuration.
For example: on the basis of the 2n2 formula, the electronic configuration of iron (atomic
number 26) is 2,8,8,8. But, it is not the case in iron. The actual electronic configuration of iron
is 2,8,14,2. It can be easily understand by Aufbau principle.
The systematic distribution of electrons in different shells and sub-shells is called electronic
configuration. On the basis of Aufbau principle, the electronic configuration of the some
elements in different shells and the sub-shells is given in the table below.
At.
Elements
H
He
Li
Be
B
C
N
O
F
Ne
Na
Mg
Al
Si
P
S
Cl
Ar
K
Ca
Sc
Cr
K
No.
No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
24
L
M
1s
2s
2p
3s
3p
1
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
1
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
1
2
3
4
5
6
6
6
6
6
6
6
6
6
6
6
6
6
1
2
2
2
2
2
2
2
2
2
2
2
N
3d
4s
1
2
3
4
5
6
6
6
6
6
1
5
1
2
2
1
Fe
26
2
2
6
2
6
6
2
Ni
28
2
2
6
2
6
8
2
Cu
29
2
2
6
2
6
10
1
Ag
47
2
2
6
2
6
10
2
O
4p
4d
6
10
Ba
56
2
2
6
2
6
10
2
6
10
U
92
2
2
6
2
6
10
2
6
10
C HEMI S TRY
4f
5s
5p
P
5d
5f
6s
10
3
2
6p
6d
6f
6
1
2
1
14
2
6
2
6
2
Optional Science - 10
0
167
S.N.
Element
Atomic number
Sub-shell electronic configuration
1
Hydrogen
1
1s1
2
Helium
2
1s2
3
Lithium
3
1s2, 2s1
4
Beryllium
4
1s2, 2s2
5
Boron
5
1s2, 2s2 2p1
6
Carbon
6
1s2, 2s2 2p2
7
Nitrogen
7
1s2, 2s2 2p3
8
Oxygen
8
1s2, 2s2 2p4
9
Fluorine
9
1s2, 2s2 2p5
10
Neon
10
1s2, 2s2 2p6
11
Sodium
11
1s2, 2s2 2p6, 3s1
12
Magnesium
12
1s2, 2s2 2p6, 3s2
13
Aluminium
13
1s2, 2s2 2p6, 3s2 3p1
14
Silicon
14
1s2, 2s2 2p6, 3s2 3p2
15
Phosphorus
15
1s2, 2s2 2p6, 3s2 3p3
16
Sulphur
16
1s2, 2s2 2p6, 3s2 3p4
17
Chlorine
17
1s2, 2s2 2p6, 3s2 3p5
18
Argon
18
1s2, 2s2 2p6, 3s2 3p6
19
Potassium
19
1s2, 2s2 2p6, 3s2 3p6, 4s1
20
Calcium
20
1s2, 2s2 2p6, 3s2 3p6, 4s2
Classification of Elements based on Electronic Configuration (s, p, d and f blocks)
According to the sub-shells electronic configuration, the periodic table is divided into four
parts. They are called blocks. The four different blocks are given below.
1.
s- block
2. p- block
3. d- block
s - Block
Period
n=1
n=2
n=3
…………..
…………
0
IIA
IIIA
……..………………… d - Block …….…………………
IIIB
IVB
VB
VIB VIIB
VIII
n=5
n=6
n=7
168
p - Block
IA
n=4
0
4. f- block
Optional Science - 10
C HEMI S TRY
IB
IIB
IVA
VA
VIA VIIA
1=---=~[JJTT--+-+-T T ~ ~
* series of Lanthanide
Elements (58 to 71)
**Series of Actinide Elements
(90 to 103)
……………………………………..
1.
f – Block elements
……………………………………………
s-block
The block of alkali metals (IA) and alkaline earth metals (IIA) which is present at the lefthand side of the periodic table is called s-block. The elements which have the last electron in
"s"sub-shell are called s-block elements. Examples: Li, Na, K, Rb, Cs, Be, Mg, Ca, etc.
Fact with reason
Sodium is a s-block element. Why?
The electronic configuration of sodium (1s2, 2s2 2p6, 3s1) shows that its last electron
enters into "s" sub-shell. So, sodium is a s-block element.
2.
p-block
The block of metals, non-metals, metalloids and inert gases which are present in IIIA, IVA,
VA, VIA, VIIA and zero groups is called p-block. It is present at the right-hand side of
the modern periodic table. The elements which have the last electron in "p" sub-shell are
called p-block elements. For example: C, N, O, F, Cl, etc.
Fact with reason
Chlorine is a p-block element. Why?
The electronic configuration of chlorine (1s2, 2s2 2p6, 3s2 3p5) shows that its last electron
enters into "p" sub-shell. So, chlorine is a p-block element.
3.
d-block
The block of transitional metals which is present in between s-block and p-block of the
modern periodic table is called d-block. This block includes elements of IB to VIIB and
VIIIth groups. As the d-block is present between s-block and p-block, it is also known as
the transitional block. The elements which have the last electron in d-sub shell are called
d-block elements. Examples: Ag, Au, Fe, Cu, etc.
Fact with reason
Iron is a d-block element. Why?
The electronic configuration of iron (1s2, 2s2 2p6, 3s2 3p6, 4s2, 3d6) shows that its last
electron enters into "d" sub-shell. So, iron is a d-block element.
4.
f-block
The block of lanthanides and actinides which is present below the main periodic table
is called f-block. The elements which have last electron in "f" sub-shell are kept in this
block. It is also called the block of inner transitional elements as it is taken out from the
transitional block. In this block there are only 28 elements. Examples: Ce, Th, U, etc.
C HEMI S TRY
Optional Science - 10
169
Valence shell
The outermost shell of an atom is called valence shell. For example, in sodium the third shell
is called valence shell and in potassium the fourth shell is called valence shell. Loss or gain or
share of electrons takes place from the valence shell.
Valence electrons
The total number of electrons present in the valence shell of an atom are called valence electrons.
For example, in sodium there is one valence electron, in oxygen, there are six valence electrons
and in chlorine there are seven valence electrons.
Valency
Except six inert gases (He, Ne, Ar, Kr, Xe and Rn), other elements combine with each other
to make compounds. During the chemical combination, these elements either give or take
or share the certain number of electrons from their outermost shell. After they give, take or
share of these electrons, elements attain stable electronic configuration. Thus, the valency is
the number of electrons gained, lost or shared by an element during the chemical reaction.
For example: the valency of sodium is one as it loses one electron from its outermost shell.
Similarly, the valency of oxygen is two as it gains two electrons in its outermost shell.
In modern periodic table, the valency remains the same in the group top to bottom. Similarly,
in the period left to right, valency first increases up to four and decrease up to zero.
Element
Li
Be
B
C
N
O
F
Ne
Valency
1
2
3
4
3
2
1
0
Some elements, their electronic configuration and valency is given in the table.
S.N.
Element
Electronic configuration
Valency
1
Hydrogen
1
1 (can give or take 1)
2
3
4
5
Helium
Boron
Magnesium
Argon
2
2, 3
2, 8, 2
2, 8, 8
0 (already duplet)
3 (can give 3 electrons)
2 (can give 2 electrons)
0 (already octet)
6
7
8
9
Chlorine
Sulphur
Potassium
Sodium
2, 8, 7
2, 8, 6
2, 8, 8, 1
2, 8, 1
1 (can take 1 electron)
2 (can take 2 electrons)
1 (can give 1 electron)
1 (can give 1 electron)
10
11
12
13
Aluminium
Calcium
Fluorine
Neon
2, 8, 3
2, 8, 8, 2
2, 7
2, 8
3 (can give 3 electrons)
2 (can give 2 electrons)
1 (can take 1 electron)
0 (already octet)
Valency of the radical
Atoms or group of atoms which have common charge on them are called radicals. There
are two types of radicals. They are electropositive radicals and electronegative radicals. The
valency of the radicals is the amount of charge present on them. Some electropositive radicals
and electronegative radicals with their valencies are given below.
0
170
Optional Science - 10
C HEMI S TRY
S.N.
Sodium (Na )
2
4
1
+
Calcium (Ca )
3
+++
I Aluminium (Al )
4
1Sulphate (SO )
3
1
2
--
4
-
Nitrate (NO3 )
2
++
1
--
Carbonate (CO3 )
2
IHydroxide (OH )
1
-
5
Potassium (K )
6
Magnesium (Mg )
2
Chloride (Cl )
1
7
IHydrogen (H )
ISilver (Ag )
IZinc (Zn )
1
IOxide (O )
ICyanide (CN )
2
+
++
+
8
1
+
~
9
2
++
1
Beryllium (Be++)
L10
I
l
Valency I Electronegative radicals Valency
1
+
~
-
I
l Ammonium (NH )
1
-
IElectropositive radicals
2
Phosphate (PO4 )
---
-
--
-
1Bromide (Br )
l
-
3
-
1
-
1
Fluoride (F-)
1
I
Variable Valency
We know that iron makes two types of compounds with chlorine. They are FeCl2 and FeCl3.
Similarly copper makes CuCl and CuCl2. Did you notice two types of valency in FeCl2 and
FeCl3? In FeCl2, the valency of iron is 2 and in FeCl3, the valency of iron is 3. It means iron
shows two valency 2 and 3. Similarly, copper shows two valency 1 and 2. Such type of valency
is called variable valency. Thus, occurrence of more than one valency of an element is called
variable valency. The existence of variable valency of the elements means that they can give,
take or share different number of electrons with different atoms or different radicals. The
transitional elements (d-block elements) in the modern periodic table show variable valency
because they have two incomplete outer shells.
The elements and their variable valency are given in the table.
S.N.
Elements
1
Iron
2
Copper
3
Tin
4
Lead
5
Mercury
6
Gold
7
Antimony
Radicals
Ferrous (Fe2+)
Ferric (Fe3+)
Cuprous (Cu+)
Cupric (Cu2+)
Stannous (Sn2+)
Stannic (Sn4+)
Plumbous (Pb2+)
Plumbic (Pb4+)
Mercurous (Hg+)
Mercuric (Hg2+)
Aurous (Au+)
Auric (Au3+)
Antimonous (Sb3+)
Antimonic (Sb5+)
Valency
2
3
1
2
2
4
2
4
1
2
1
3
3
5
Fact with reason
Why do d-block elements show variable valency?
The d-block elements have two incomplete outer shells. Electrons present in these two
shells participate in chemical bonding. So, d-block elements show variable valency.
C HEMI S TRY
Optional Science - 10
0
171
Answer writing skill
1.
State Aufbau principle and write down its sequence.
Ans: According to Aufbau principle, “filling of electrons always occurs from the lower
energy level to the higher energy level.” The sequence is given below:
1s< 2s< 2p< 3s< 3p< 4s< 3d< 4p< 5s< 4d< 5p< 6s< 4f < 5d < 6p < 7s……..
2.
What are d-block elements? Why are they called transitional elements?
Ans: Those elements whose last electron enters into d-orbital are called d-block elements.
They are called transitional elements because they are present in between s-block and
p-block.
3.
What is ionization potential? How does it change across the period and down the
group?
Ans: The amount of energy required to remove the loosely bonded outermost electron
from an isolated gaseous atom is called ionization potential. In the period left to right,
ionization potential increases as the atomic size decreases. Similarly, the value of
ionization potential decreases in the group top to bottom, as atomic size increases.
4.
Write down a main difference between Mendeleev's Periodic table and Modern
Periodic table?
Ans: Mendelveev's periodic table is based on increasing atomic weight but Modern periodic
table is based on increasing atomic number.
5.
Which has bigger atomic size between sodium and potassium? Why?
Ans: Potassium has bigger atomic size between sodium and potassium. This is because
potassium has four atomic shells and sodium has only three atomic shells. Due to more
number of shells, potassium has bigger atomic size.
6.
Why are fluorine and chlorine kept in p-block?
Ans: The electronic configuration of fluorine is 1s2, 2s2 2p5 and the electronic configuration of
chlorine is 1s2, 2s2 2p6, 3s2 3p5. This electronic configuration shows that the last electron
of the fluorine and chlorine lie in the "p" sub-shell. So, they lie in p-block.
7.
Write any two differences between s-block and p-block elements.
Ans:
S.N. s-block elements
1
2
0
172
S.N. p-block elements
s-block elements have the last 1
electron in "s" sub-shell.
All s-block elements are metal. 2
p-block elements have the last electron in
"p" sub-shell.
p-block elements are metals, non-metals,
metalloids and inert gases.
Optional Science - 10
C HEMI S TRY
8.
Write down any three characteristics of the Modern Periodic Table.
Ans: The main characteristics of the modern periodic table are given below:
i.
In modern periodic table, elements are arranged on the basis of their increasing
atomic numbers.
ii.
In this table, there are seven periods and 18 groups.
iii. Inert gases like He, Ne, Ar, Kr, Xe and Rn are placed in a separate group (zero
group or 18th group) at the extreme right side of the table.
9.
Write down any thee advantages of the periodic table.
Ans: The advantages of the periodic table are given below.
i.
The detail information about the elements like the number of electrons, number of
protons, electronic configuration, atomic number, atomic weight, valency, nature,
block, etc. can be obtained from the periodic table.
ii.
With the help of periodic table, the properties of elements can be studied easily.
iii. The periodic variations such as atomic number, valency, atomic radius, ionization
potential, electronegativity, electron affinity, etc. can be studied easily with the
help of periodic table.
10.
How does modern periodic table remove the defects of the Mendeleev's Periodic table?
Ans: In the modern periodic table, elements are classified on the basis of increasing atomic
numbers. This system of classification helped to solve the defects of Mendeleev's
periodic table in the following ways.
1.
The position of hydrogen is fixed: The accurate position of hydrogen has not yet
been solved completely. But as its atomic number is the least number (i.e. one), it
is kept in IA (group 1) group of the modern periodic table along with alkali metals.
2.
The position of isotopes is fixed: Isotopes are the atoms of the same elements,
which have the same atomic numbers but different atomic weights. Therefore,
isotopes of one element are placed together in the same group. For example,
there are three isotopes of carbon (i.e. C612, C613 and C614) which have same atomic
numbers. They are placed together in IVA group of the modern periodic table.
3.
The wrong position of the elements has been corrected: When elements are
arranged on the basis of their increasing atomic numbers, the wrong position of
argon, potassium, nickel, cobalt, etc. is solved automatically without changing
their own places.
4.
The alkali metals and coinage metals are kept separately: In the modern periodic
table, the most reactive alkali metals are kept in IA group (group 1) whereas the
least reactive coinage metals are kept in IB group (group11).
5.
Lanthanides and actinides are kept below the main table: In the modern periodic
table, fourteen elements of lanthanide series and fourteen elements of actinide
series are placed in a separate box below the main periodic table.
C HEMI S TRY
Optional Science - 10
173
Exercise
Step
1.
1
Define the following terms:
i.
2.
Mendeleev's periodic table
ii.
Modern periodic table
iii. Aufbau principle
iv. Electronic configuration
v.
Valency vi. Variable valency
vii. Ionization Potentaial
viii. Electronegativity
ix. Electron affinity
x.
Alkali metals
xi. Alkaline earth metals
xii. s-block elements
xiii. p-block elements
xiv. d- block elements
xv. f-block elements
Write electronic configuration of given elements on the basis of sub-shells.
i. Na1123
Step
1.
ii. Cl1735
iii. K1939
iv. Ca2040
2
Write two differences between:
i.
Modern periodic table and Mendeleev’s periodic table
ii.
Periods and groups
iii. s- block elements and p- block elements
2.
Give reason.
i.
Elements of IA group of the modern periodic table are called alkali metals.
ii.
Elements of IIA group of the modern periodic table are called alkaline earth metals.
iii. Fluorine is kept in p-block of the modern periodic table.
iv. Potassium is kept in the s-block of the periodic table.
v. Electron affinity increases in the period left to right and decreases top to bottom in
the group.
174
Optional Science - 10
C HEMI S TRY
vi. Electronegativity increases in the period left to right and decreases in the group top to
bottom.
vii. The electronic configuration of chromium and copper does not follow the Aufbau
Principle.
viii. As we move from top to bottom, atomic size increases.
ix. As we move from top to bottom, the ionization potential decreases.
Step
3
1.
What is Mendeleev's Periodic table? Write down its characteristics.
2.
What is Modern Periodic table? Write down its characteristics.
3.
Explain the demerits of the Mendeleev's periodic table in the points.
4.
Enlist the advantages of the Mendeleev's periodic table.
5.
What are the advantages of the periodic table? Write down in points.
6.
What are the characteristics that is why hydrogen can be placed in the IAgroup of the
modern periodic table?
7.
Discuss the characteristics that is why hydrogen can be placed in the VIIA group of the
modern periodic table.
8.
Discuss the drawbacks of the Mendeleev's Periodic table.
9.
What is valency and variable valency? Generally d-block elements show variable
valency, why?
10.
Write down two examples of elements and their electronic configuration where Aufbau
principle is not followed.
Step
4
1.
Describe the s, p, d and f blocks of the modern periodic table.
2.
Explain the periodic variation of ionization potential, electronegativity, electron affinity
and atomic radius.
C HEMI S TRY
Optional Science - 10
0
175
Multiple choice questions:
1.
Mendeleev's periodic table is based on increasing
2.
a.
Atomic number
b.
Atomic weight
c.
Electron numbers
d.
Protons number
Mendeleev's periodic table has
3.
a.
7 periods and 18 groups
b.
7 periods and 8 groups
c.
8 periods and 7 groups
d.
18 periods and 7 groups
The maximum number of electrons in s and p orbitals are
4.
a.
2 and 5
b.
2 and 9
c.
3 and 6
d.
2 and 6
The valency of SO4 in H2SO4 is
5.
a.
1
b.
2
c.
3
d.
4
The symbol of ferrous and ferric are:
6.
a.
Fe3+ and Fe2+
b.
Fe2+ and Fe
c.
Fe2+ and Fe3+
d.
Fe and Fe+
The unit of ionization potential is
7.
a.
Potential volt
b.
Electron volt
c.
Pascal
d.
Joule
Which of the following shows variable valency?
8.
a.
Sodium
b.
Calcium
c.
Iron
d.
Potassium
Ionization potential increases in
9.
a.
Group
b.
Period
c.
Block
d.
None of the above
What is the value of azimuthal quantum number for d sub-shell?
10.
0
176
a.
1
b.
2
c.
3
d.
4
What is the correct electronic configuration of chromium?
a.
1s2, 2s2 2p6, 3s2 3p6, 4s2, 3d4
b.
1s2, 2s2 2p6, 3s2 3p6, 4s1, 3d5
c.
1s2, 2s2 2p6, 3s2 3p6, 4s2, 3d9
d.
1s2, 2s2 2p6, 3s2 3p6, 4s1, 3d10
Optional Science - 10
C HEMI S TRY
UNIT
CHEMICAL
BONDING AND
CHEMICAL
ARITHMETIC
9
About the inspiring personality
Avogadro born in 1776 and died in 1856. He is best known for his law that "equal volumes
of different gases contain an equal number of molecules, provided they are at the same
temperature and pressure". He worked as a professor in mathematical physics in Turin
University.
Syllabus issued by CDC
Theory
Practical
6
2
Learning objectives:
At the end of this unit, students will be able to:
•
• Types of bonding (Ionic, covalent
•
and coordinate)
• Sigma and pi bonds
• Avogadro's law
•
• Chemical calculation
• Structure of electrovalent compounds
(NaCl, MgCl2 and CaO)
• Structure of covalent compounds
(H2, O2, N2, H2O, NH3 and CH4)
• Structure of coordinate compounds
(O3 and SO3)
Explain sigma bond, pi bond and coordinate
bond along with the chemical compounds.
Explain Avogadro’s number and chemical
arithmetic.
Solve the simple numerical problems based on
Avogadro’s number and chemical arithmetic.
Key terms and terminologies of the unit
I
1.
Bond: The force of attraction which binds two or more elements together to make a
stable chemical compound is called bond.
2.
Octet: Octet state is the electronic configuration in which there are eight electrons in the
valence (outermost) shell of an atom.
C HEMI S TRY
Optional Science - 10
177
3.
Octet rule: The tendency of an element to make eight electrons in the outermost shell
as a result of gain or lose or share of electrons is called octet rule.
4.
Duplet: Duplet is the state of electronic configuration in which an atom has only one
shell (K-shell) with 2 electrons in it.
5.
Electrovalent bond: The chemical bond which is formed in between two opposite
charges as a result of transfer of electrons is called electrovalent bond.
6.
Covalent bond: The chemical bond which is formed by mutual sharing of electrons
in between two or more non-metal atoms is called covalent bond.
7.
Single covalent bond: In single covalent bond one pair of electrons is shared between
two non-metal atoms.
8.
Double covalent bond: In double covalent bond, two pairs of electrons are shared
between two non-metal atoms.
9.
Triple covalent bond: In triple covalent bond, three pairs of electrons are shared
between two non-metal atoms.
10.
Electrovalent compounds: The chemical compounds which are formed as a result of
electrovalent bonding are called electrovalent compounds or ionic compounds.
11.
Covalent compounds: The chemical compounds which are formed as a result of
covalent bonding are called covalent compounds.
12.
Coordinate bond: The type of chemical bond in which one of the combining atoms
contributes both of the shared electrons is called coordinate bond.
13.
Coordinate compounds: Those chemical compounds which are formed as a result of
coordinate bonding are called coordinate compounds.
14.
Sigma and pi bonds: The covalent bond which are formed by the overlapping of the
atomic orbitals is called sigma and pi bonds.
15.
Sigma-bond: The type of chemical bond which is formed due to head to head
overlapping of the atomic orbitals is called sigma bond.
16.
Pi- bond: The type of chemical bond which is formed due to side to side overlapping
of the atomic orbitals is called pi-bond.
17.
Avogagro's Principle: According to Avogagro's Principle "Under the constant
temperature and pressure, equal volumes of all gases contain equal number of
molecules".
Introduction
Scientists discovered altogether 118 elements till today. Most of these elements are unstable.
Except six inert gases all other elements react with each other to make stable compounds. When
two or more combining elements come near together, a force of attraction occurs between the
atoms. This force of attraction is responsible to bind these atoms. This attractive force is called
chemical bond. Therefore, the force of attraction which binds two or more elements together
to make a stable chemical compound is called bond.
0
178
Optional Science - 10
C HEMI S TRY
Elements are unstable because they have incomplete outermost shell. For example, sodium
is unstable because it has one electron in its outermost shell. Similarly, chlorine is unstable
because it has seven electrons in its outermost shell. Thus, those elements which have eight
electrons in their outermost shell (except helium) are stable in nature. In order to make
chemical bonding, it is necessary for an atom to attain stable electronic configuration like inert
gages. This stable electronic configuration is called duplet state and octet state.
Fact with reason
Except inert gases other elements are chemically unstable. Why?
Except inert gases other elements do not have complete outermost shell. This is why
they want to combine with other elements to gain stability. Thus, except inert gases other
elements are chemically unstable.
Octet and Octet Rule
Out of 118 elements, five elements, viz. Neon (Ne), Argon (Ar), Krypton (Kr), Xenon (Xe) and
Radon (Rn) have eight electrons in their outermost shell. The electronic configuration of these
elements is called octet state. Thus, octet state is the electronic configuration in which there
are 8 electrons in the valence (outermost) shell of an atom. It is observed that if an atom has
8 electrons in its outermost shell, it becomes chemically stable. These stable elements neither
give or take nor share electrons. Except these five elements, other elements are chemically
unstable. These elements give or take or share electrons to make complete octet. This tendency
of an element is called octet rule. Therefore, the tendency of an element to make eight electrons
in the outer most shell as a result of gain or lose or share of electrons is called octet rule. For
example, sodium loses one electron and chlorine gains one electron to obtain octet.
Atomic structure of neon (Ne), Argon (Ar), Krypton (Kr), Xenon (Xe) and Radon (Rn)
I
I
I
S.N.
Inert gas
I
Symbol
Atomic
number
Electronic configuration
L I M
N
O
8 I
2
Neon
Ne
10
K
2
3
Argon
Ar
18
2
4
Krypton
Kr
36
2
8
5
Xenon
Xe
54
2
8
6
Radon
Rn
86
2
I
I
8
I
8
I 8 I
I 18 I 8
18 I 18
I
I 18 I 32
7
P
-
-
8
I
18
8 _J
Duplet and Duplet Rule
Helium is a single element which has only one shell (K-shell) in its atomic structure. In this
K-shell, there are two electrons. It has been observed that, chemically helium is stable. So,
the state of electronic configuration of helium is called duplet. Duplet is the state of electronic
configuration in which an atom has only one shell (K-shell) with 2 electrons in it. There are
few elements like hydrogen, lithium, beryllium and boron which can form duplet by giving,
taking or sharing of electrons. It is called duplet rule. Therefore, the tendency of an element
to make two electrons in the outermost K-shell as a result of gain or lose or share of electrons
is called duplet rule.
C HEMI S TRY
Optional Science - 10
179
Fact with reason
Why are inert gases chemically stable?
Inert gases like helium, neon, organ, krypton, xenon and radon are chemically stable
because they have eight electrons in their outermost shell except helium. These elements
do not gain, take and share electrons. So, inert gases are chemically stable.
Chemical bonding
As we have discussed that, except inert gases other elements are chemically unstable and
combine together to make stable chemical compounds. In the chemical compounds, atoms
of the elements are combined together by a force of attraction called chemical bond. Due to
chemical bond, it is possible to make stable chemical compounds. According to the nature,
different kinds of chemical bonds are present in the compounds. In this unit, we will discuss
three different types of chemical bonds. They are given below.
i. Ionic or Electrovalent Bond
ii. Covalent Bond
iii. Coordinate Bond
Ionic or electrovalent bond
Metals have one, two or three electrons in their valence shell. Similarly, non-metals have five
or six or seven electrons in their valence shell. According to octet and duplet rules metals lose
electrons and non-metals gain electrons to complete octet or duplet. As a result metals become
positively charged and non-metals become negatively charged. In between these opposite
charges there occurs an electrostatic force of attraction called electrovalent bond. Thus, the
chemical bond which is formed in between two opposite charges as a result of transfer of
electrons is called electrovalent bond.
—e—
Na2, 8, 1 → Na+2, 8
+ e—
Cl2, 8, 7 →Cl–2, 8, 8
NaCl
Fig: Process of formation of electrovalent bonding
Memory Plus
The chemical bond which is formed by giving and taking of electrons between metals and
non-metals is called electrovalent bond or ionic bond.
Fact with reason
Electrovalent bond is also called ionic bond. Why?
In electrovalent bond transfer of electrons takes place from metals to non-metals. As a result,
metal gains positive charge and non-metal gains negative charge. In between these two
opposite charges electrostatic force of attraction takes place. Due to this force of attraction
opposite ions combine together to give compound. If this compound is kept in water, it also
gives corresponding opposite ions. Thus, electrovalent bond is also called ionic bond.
0
180
Optional Science - 10
C HEMI S TRY
Electrovalent compounds or ionic compound
There are large numbers of chemical compounds like, NaCl, KCl, MgCl2, NH4Cl, CaCl2,
CaCO3, etc. which are formed as a result of electrovalent bonding are called electrovalent
compounds. They are also called ionic compounds as they give opposite ions (cations and
anions) after the process of ionization. Thus, the chemical compounds which are formed as a
result of electrovalent bonding are called electrovalent compounds or ionic compound.
Characteristics of electrovalent compounds
1.
Electrovalent compounds are formed as a result of electrovalent bonding.
2.
They have high melting and boiling point.
2.
They are strong chemical compounds as there is strong electrostatic force of attraction.
3.
They are soluble in water but insoluble in organic solvents like ether, benzene, carbon
tetra chloride, etc.
4.
They do not have the fixed geometrical shape.
5.
In fused or solution state electrovalent compounds conduct electricity.
Memory Plus
Electronegative ions are also called acid radicals or anions. Similarly electropositive ions
are also called basic radicals or cations.
Covalent bond
Electrovalent bond is limited only in between two opposite charges (generally in between
metals and non-metals). But there are many chemical compounds which are formed by
combining two or more non-metals. For example: CH4, CO2, NH3, O2, N2, Cl2, etc. These
compounds are formed by mutual sharing of one or more electrons between the combining
atoms. The bond present in these compounds is called covalent bond. Thus, the chemical bond
which is formed by mutual sharing of electrons in between two or more non-metal atoms is
called covalent bond.
In a covalent bond, the pairing electrons come from both atoms in equal number. It means that
each sharing atom contributes equal number of electrons to the bond. For example, in hydrogen
there is one electron in its valence shell and chlorine has seven electrons in its valence shell.
Hydrogen needs one electron to complete duplet and chlorine needs one electron to make
octet. While making hydrochloric acid (HCl), hydrogen makes duplet and chlorine makes
octet. Therefore, both elements provide one electron each to make single covalent bond. The
pair of electrons that are shared by hydrogen and
chlorine are called share-pair electron. Similarly, the
pair of electrons which do not use in bonding are
H~
lone pair of
/
electrons
called lone pairs of electrons. In the compound HCl,
hydrogen does not have lone pair of electrons but shared pair of electrons in which each atom
contributes one electron
chlorine has three lone pair of electrons.
fig:formation of chemical bond in HCl
Types of covalent bonds
While making covalent bond, non-metal atoms share one or more pair of electrons. On the
basis of number of share-pair of electrons, there are three types of covalent bonds. They are:
C HEMI S TRY
Optional Science - 10
0
181
i) Single covalent bond
In single covalent bond one pair of electrons
is shared between two non-metal atoms. For
example, the bond between two hydrogen
atoms in H2, the bond between hydrogen
and oxygen atoms in H2O, the bond between
carbon and hydrogen atoms in CH4, etc. The
single covalent bond is represented by using
single line (–).
0
H-H
/\
H
II, molecule
H
11, 0 m olecule
H
I
H-C-H
I
H
CII4 m olecule
examples of single covalent bond in different molecules
ii) Double covalent bond
In double covalent bond, two pairs of elec-
trons are shared between two non-metal
atoms. For example: The covalent bond between two oxygen atoms in O2, the bond between carbon and oxygen atoms in CO2, the
covalent bond between two carbon atoms in
ethene (CH2= CH2), etc. The double covalent
bond is represented by using double lines (=)
between two atoms.
CO2molecule
Oxygen molecule
examples of double covalent bond in different molecules
iii) Triple covalent bond
In triple covalent bond, three pairs of elec-
N=N
H-C=N
trons are shared between two non-metal atNitrogen molecule
HCN molecule (Hydrogen cyanide)
oms. For example: The bond between nitroexamples of triple covalent bond in different molecules
gen atoms in N2 (N≡N), the bond between carbon and nitrogen atoms in HCN (H-C≡N),
the bond between two carbon atoms of ethyne C2H2(CH≡CH),etc. The triple covalent
bond is represented by using triple lines (≡).
Covalent compounds
The chemical compounds which are formed as a result of covalent bonding are called covalent
compounds. For example: CH4, CO2, H2O, CCl4, NH3, O2, N2, Cl2, H2, etc. All the covalent
compounds are formed between the non-metal atoms. These compounds have low melting
and boiling point.
Characteristics of the covalent compounds
1.
Covalent compounds are formed by covalent bonding.
2.
Covalent compounds have low melting and boiling point as compared to the electrovalent
compounds.
2.
They are weaker than electrovalent compounds.
3.
They are insoluble in water but soluble in organic solvents.
4.
They have fixed geometrical shape.
5.
They do not conduct electricity in aqueous solution.
182
Optional Science - 10
C HEMI S TRY
Differences between electrovalent and covalent bonds
S.N. Electrovalent bond
1.
2.
3.
S.N. Covalent bond
Electrovalent bond is formed by the 1.
transfer of electrons from metal to
non-metal.
It is a stronger bond.
2.
It is formed between metal and 3.
non-metal atoms.
Covalent bond is formed by the sharing
of electrons between two non-metal
atoms.
It is a weaker bond.
It is formed between non-metal atoms.
Differences between electrovalent and covalent compounds
S.N. Electrovalent compounds
1.
2.
3.
4.
5.
S.N. Covalent compounds
Electrovalent compounds are formed 1.
by electrovalent bonding.
Generally, they are harder, stronger, 2.
brittle and crystalline solid.
They have high melting and boiling 3.
point.
Generally, they are soluble in water 4.
but insoluble in organic solvent.
They are good conductor of electricity 5.
in molten and solution state.
Covalent compounds are formed by
covalent bonding.
Generally, they are gases, liquids or soft
solids.
They have low melting and boiling
point.
Generally, they are soluble in organic
solvent but insoluble in water.
They are bad conductor of electricity.
Coordinate Bond
The type of chemical bond in which one of the combining atoms contributes both of the shared
electrons is called coordinate bond. A coordinate bond is similar to a covalent bond but in a
coordinate bond, only one atom contributes for the bonding. We represent a coordinate bond
by using an arrow (→) instead of a dash (–). In a coordinate bond, the atom which donates a
pair of electrons is called donor atom and the atom which receives the electron pair is called
recipient atom. The arrow is always faces from donor to the recipient atom.
Example 1: Formation of ammonium ion (NH4+)
In ammonia, the nitrogen atom contains a lone pair of electrons after completing its octet. A
hydrogen ion needs two electrons to complete its duplet. So, hydrogen ion accepts the lone
pair of electrons from nitrogen atom. Thus, a
coordinate bond is formed between ammonia
and hydrogen ion to make ammonium
ion(NH4+).
NH3 + H+ NH4+
formation of ammonium ion
Example 2: Formation of hydronium ion (H3O )
+
In water molecule, there are two lone pair of electrons in oxygen atom. Similarly, a hydrogen
ion does not have electrons. So, it needs two electrons to complete duplet. Now, hydrogen
ion accepts a lone pair of electrons from the oxygen atom. Thus, a coordinate bond is formed
between water and hydrogen ion.
H2O + H+[H3O]+
C HEMI S TRY
Optional Science - 10
183
Memory Plus
Coordinate bonding is a combination of covalent and electrovalent bonding.
Sigma and Pi bonds
In the atomic structure, different orbitals have different shapes. The s-orbital is spherical
shaped, p-orbital is dumb bell shaped, d-orbital is double dumb bell shaped and the shape of
f-orbital is complex. When atoms combine with each other, these orbitals overlap in different
ways. After their overlapping, covalent bond is formed. The way of overlapping is different
in different compounds. The type
of bond formed between atoms
depends upon how their orbitals
y
overlap. The overlapping of orbitals
can occur between s and s orbitals,
p and p orbitals, s and p orbitals
and so on. Thus, the covalent bond
p
d
formed by the overlapping of the
fig:shapes of atomic orbitals
atomic orbitals is called sigma and
pi bonds.
1. Sigma Bond (σ)
The type of chemical bond which is formed
due to head to head overlapping of the atomic
orbitals is called sigma bond. The sigma bond
is represented by a Greek letter sigma (σ). It
is stronger than a pi bond. There are three
possibilities of forming sigma bond. They are:
a.
b.
c.
Overlapping of two s-orbitals
Overlapping of two p-orbitals
Overlapping of one s and one p orbitals
(a)
~
•
s
~z •
s
.
ffi
~
s
~
(bJ
~
(a-) Sigm a bond
c.+a
X
X
z
-
Sig ma (a-) bo nd
P
c,i ~El z • oio
p ,,
Pz
()3jo z
z
-
ojEDjo
z
Sigm a (a") bo nd
fig: formation of a sigma bond due to (a) s-s overlap
(b) s-p overlap (c) p-p overlap
2. Pi Bond (p-bond)
The type of chemical bond which is formed due to side to side
overlapping of the atomic orbitals is called pi bond. It is represented
by a Greek letter Pi (π). Pi bond is a weaker covalent bond compared to
the sigma bond. There is only one way by which a pi bond is formed
fig:sidewise overlap of
i.e. side to side overlapping of the atomic orbitals.
p-orbitals forπ bond
It has been observed that a compound having single covalent bond between two carbon
atoms (C-C) or between carbon and hydrogen atoms (C-H) is always sigma bond.
Similarly, in any double covalent bond, there is one sigma bond and one bond. In the
same way, in a triple covalent bond, there is one sigma bond and two pi bonds.
In organic chemistry, one carbon atom can combine with another carbon atom making single,
double or triple covalent bonds. In these covalent bonds, the total numbers of sigma and pi
bonds are given in the table:
184
Optional Science - 10
C HEMI S TRY
S.N.
Type of Bond
Total number of
sigma bond
Total number of pi bond
1
C-C (sigma bond)
1
0
2
C=C (double bond)
1
1
3
C≡C (triple bond)
1
2
Examples of ionic compounds
Those chemical compounds which are formed as a result of electrovalent bonding are called
electrovalent compounds or ionic compounds. The formation and structure of different ionic
compounds like NaCl, MgCl2, CaO, etc. are described below.
a. Formation of sodium chloride (NaCl)
Sodium chloride (NaCl) is an example of
sodium contributes
electrovalent compound. It is formed by
electro11, leaving It
combining sodium metal and chlorine non-metal.
v~lh a closed sholl
Sodium has electronic configuration 2, 8, 1 and
••
+
.....
Na + , Cl ,
chlorine has electronic configuration 2, 8, 7. Na• + • Cl : . /\
forming ionic
.----' ~---..
According to octet rule, the above electronic
bond
chlorine gains
configuration shows that, sodium has one extra
electron, leaving II
with a closed shell
electron and chlorine requires one more electron
fig:formation of NaCl
to attain stable electronic configuration. Thus, in
order to make sodium chloride, sodium loses one electron and makes sodium ion (Na+).
Similarly, chlorine gains one electron and makes chloride ion (Cl-). In between these opposite
ions there occurs a force of attraction called electrostatic force of attraction or electrovalent
bond. As a result, sodium and chloride combine together to give sodium chloride (NaCl)
molecule.
..
Na (2,8,1)
+
Cl (2,8,7)
.
Na+ (2,8) Cl- (2,8,8)
+
..
~
~
Na
Sodium atom
Cl
Chlorine atom
II
Na+
Sodium ion
(a cation)
Ct"
Chloride ion
(an anion)
Sodium chloride (NaCl)
Fact with reason
Sodium chloride is an electrovalent compound. Why?
Sodium chloride is formed by the transfer of electron from sodium to chlorine.
Transfer of electrons from metal to non-metal makes electrovalent bonding. So,
sodium chloride is an electrovalent compound.
C HEMI S TRY
Optional Science - 10
185
b. Formation of magnesium chloride (MgCl2)
Magnesium chloride is an example of electrovalent compound. It is formed by combining
magnesium metal and chlorine non-metal. Magnesium has electronic configuration 2,
8, 2 and chlorine has electronic configuration 2, 8, 7. According to octet rule, the above
electronic configuration shows that, magnesium has two extra electrons and chlorine
requires one more electron to attain stable octet state. Thus, in order to make magnesium
chloride, magnesium loses two electrons and makes magnesium ion (Mg++). Similarly,
two chlorine atoms gain one electron each to make chloride ions (2Cl-). In between one
magnesium ion and two chloride ions there occurs a force of attraction called electrostatic
force of attraction or electrovalent bond. As a result, magnesium chloride (MgCl2)
molecule is formed. Here, magnesium chloride is formed by the transfer of electrons from
magnesium to chlorine (electrovalent bonding), it is an electrovalent compound.
Mg (2,8,2) + 2Cl (2,8,7) Mg++ (2,8) Cl- (2,8,8) Cl- (2,8,8)
Each magnesium atom loses
two electrons to form a
magnesium ion. ~
Each chlorine atom gains an
I
r,/~- '°
(W}~
booomo ,cbloriddoo.
@»:~! •[@)J[@r[@)l
'--A@);
I
I
xx
X
Cl !
~ xx
Mg: +
xx
~
---
Cl !
xx
Electrostatic attraction arises between
magnesium and chloride ions.
Magnesium chloride is formed .
fig:Formation of magnesium chloride (MgCl2)
Fact with reason
Magnesium chloride is an electrovalent compound. Why?
Magnesium chloride is formed by the transfer of electron from magnesium to chlorine.
The transfer of electrons from metal to non-metal makes electrovalent bonding. So,
magnesium chloride is an electrovalent compound.
c. Formation of calcium oxide (CaO)
Calcium oxide is an example of electrovalent compound. It is formed by combining
calcium metal and oxygen non-metal. Calcium has electronic configuration 2, 8, 8, 2 and
oxygen has electronic configuration 2, 6. According to octet rule, the above electronic
configuration shows that, calcium has two extra electrons and oxygen requires two more
electrons to attain stable octet state. Thus, in order to make calcium oxide, calcium loses
two electrons and makes calcium ion (Ca++) resembling to electronic configuration of
argon. Similarly, oxygen atom gains two electrons to make oxide ion (O--) resembling
to electronic configuration of neon. In between one calcium ion and one oxide ion there
occurs a force of attraction called electrostatic force of attraction or electrovalent bond. As
a result,calcium oxide (CaO) molecule is formed. Here, calcium oxide is formed by the
transfer of electrons from calcium to oxygen (electrovalent bonding), it is an electrovalent
compound.
186
Optional Science - 10
C HEMI S TRY
({i/~ @( :
~
.
r
p
~
2
0
[
~
p
=
8
~ J """ ~ J "'
Calcium 2, 8, 8, 2
'
l
Calcium lon(2. 8, 8)
Oxygen 2,6
o: - - > Caz+ [ :§: ] 2- (or)
,.,-----..__, ..
Ca : +
Calcium atom
Oxygen atom
2, 8, 8, 2
2, 6
Calcium u,n Oxide ion
2, 8, 8
2, 8
Calcium oxide
Oxide lon(2, 8)
fig:formation of calcium oxide (CaO)
Fact with reason
Calcium oxide is an electrovalent compound. Why?
Calcium oxide is formed by the transfer of electrons from calcium to oxygen. The
transfer of electrons from metal to non-metal makes electrovalent bonding. So, calcium
oxide is an electrovalent compound.
Examples of covalent molecules
Those molecules which are formed as a result of covalent bonding are called covalent
molecules. For example: H2, O2, N2, Cl2, H2O, CH4 , NH3, etc. The formation and structure of
some covalent molecules are described below:
a. Formation of hydrogen molecule (H2)
Hydrogen has one electron in its k-shell. According to
duplet rule, it needs one more electron to attain stable
electronic configuration similar to helium atom. Therefore,
two hydrogen atoms share one electron each to make fig:formation of hydrogen molecule (H2)
hydrogen molecule. Here, hydrogen molecule is formed as a result of sharing of electrons
(covalent bonding), it is a covalent molecule.
Fact with reason
Hydrogen (H2) is a covalent molecule. Why?
Hydrogen molecule is formed as a result of sharing of electrons between two
hydrogen atoms. The sharing of electrons makes covalent bonding. So, hydrogen (H2)
is a covalent molecule as it has covalent bonding.
b. Formation of nitrogen molecule (N2)
Nitrogen is a non-metal. Its electronic configuration is 2,
N
o=2.5
N. - ~
5. The electronic configuration shows that nitrogen has
. .
~
five electrons in its valence shell. According to octet rule,
N+N N2
it needs three more electrons to attain stable electronic fig:formation of nitrogen molecule (N2)
configuration similar to electronic configuration of neon. Therefore, two nitrogen atoms
share three electrons each to make nitrogen molecule. Here, nitrogen molecule is formed
by the sharing of electrons (covalent bonding), it is a covalent molecule.
·O
·
C HEMI S TRY
Optional Science - 10
187
Fact with reason
Nitrogen (N2) is a covalent molecule. Why?
Nitrogen molecule is formed as a result of sharing of electrons between two
nitrogen atoms. The sharing of electrons makes covalent bonding. So, nitrogen (N2)
is a covalent molecule as it has covalent bonding.
c. Formation of oxygen molecule (O2)
Oxygen is a non-metal. Its electronic configuration
is 2, 6. This electronic configuration shows that
oxygen has six electrons in its valence shell.
According to octet rule, it needs two more electrons
fig:formation of oxygen molecule (O2)
to attain stable electronic configuration similar to
electronic configuration of neon. Therefore, two oxygen atoms share two electrons each
to make oxygen molecule. Here, oxygen molecule is formed by the sharing of electrons
(covalent bonding), it is a covalent molecule.
@@- @@
+
0
0
O= O
Fact with reason
Oxygen (O2) is a covalent molecule. Why?
Oxygen molecule is formed as a result of sharing of electrons between two oxygen
atoms. The sharing of electrons makes covalent bonding. So, oxygen (O2) is a covalent
molecule as it has covalent bonding.
d. Formation of water molecule (H2O)
In water, there is one oxygen
atom and two hydrogen atoms.
The electronic configuration of
oxygen is 2, 6. In this electronic
configuration, there are six
~
I
electrons in the valence shell
fig:3D structure of water molecule
fig:formation of water molecule (H2O)
of oxygen. According to octet
rule it needs two electrons to attain stable electronic configuration similar to electronic
configuration of neon. Similarly, in hydrogen, there is one electron in its valence shell (or
K-shell). According to duplet rule, hydrogen needs one electron to attain stable electronic
configuration similar to helium. Therefore, one oxygen atom shares two electrons with
two hydrogen atoms and forms water molecule. Here, water molecule is formed as a
result of sharing of electrons (covalent bonding), it is a covalent molecule.
@(!) - (0fo)
w
- '@
H- 0
2H
+
0
H
Fact with reason
Water (H2O) is a covalent molecule. Why?
Water molecule is formed as a result of sharing of electrons between one oxygen atom
and two hydrogen atoms. The sharing of electrons makes covalent bonding. So, water
(H2O) is a covalent molecule as it has covalent bonding.
188
Optional Science - 10
C HEMI S TRY
e. Formation of methane molecule (CH4)
H
I
or 1-1-C- H
k
fig:3D structure of methane molecule
fig:formation of methane molecule (CH₄)
In methane there is one carbon atom and four hydrogen atoms. The electronic configuration
of carbon is 2, 4. In this electronic configuration, there are four electrons in the valence
shell of carbon. According to octet rule it needs four electrons to attain stable electronic
configuration similar to electronic configuration of neon. Similarly in hydrogen, there is
one electron in its valence shell (or k-shell). According to duplet rule, hydrogen needs one
electron to attain stable electronic configuration similar to helium. Therefore, one carbon
atom shares four electrons with four hydrogen atoms and forms methane molecule. Here,
methane molecule is formed as a result of sharing of electrons (covalent bonding), it is a
covalent molecule.
Fact with reason
Methane (CH4) is a covalent molecule. Why?
Methane molecule is formed as a result of sharing of electrons between one carbon
atom and four hydrogen atoms. The sharing of electrons makes covalent bonding. So,
methane (CH4) is a covalent molecule as it has covalent bonding.
f. Formation of ammonia molecule (NH3)
In ammonia, there is one nitrogen atom and three hydrogen atoms. The electronic
configuration of nitrogen is 2, 5. In this electronic configuration, there are five electrons
in the valence shell of nitrogen. According to octet rule it needs three electrons to attain
stable electronic configuration similar to electronic configuration of neon. Similarly, in
hydrogen, there is one electron in its valence shell (or K-shell). According to duplet rule,
hydrogen needs one electron to attain stable electronic configuration similar to helium.
Therefore, one nitrogen atom shares three electrons with three hydrogen atoms and forms
ammonia molecule. Here, ammonia molecule is formed as a result of sharing of electrons
(covalent bonding), it is a covalent molecule.
H
••
•N• + 3[xH]
➔
Ammonia
~
or
fig:formation of ammonia molecule (NH₃)
C HEMI S TRY
I
H-N-H
II
t
lone pair
fig:3D structure of ammonia molecule
Optional Science - 10
189
Fact with reason
Ammonia (NH3) is a covalent molecule. Why?
Ammonia molecule is formed as a result of sharing of electrons between one nitrogen
atom and three hydrogen atoms. The sharing of electrons makes covalent bonding.
So, ammonia (NH3) is a covalent molecule as it has covalent bonding.
Examples of coordinate compounds
Those chemical compounds which are formed as a result of coordinate bonding are called
coordinate compounds. For example: ozone molecule (O3), sulphur trioxide molecule (SO3),
carbon monoxide molecule (CO), etc.
a. Structure of Ozone molecule (O3)
Ozone is a molecule which contains three oxygen atoms. It is also called trioxygen
molecule. The electronic configuration of oxygen atom is 2,6. According to the electronic
configuration, there are six electrons in the valance shell of an oxygen atom. On the basis
of octet rule, each oxygen atom needs two electrons to complete its octet similar to the
electronic configuration of neon. Now, the two oxygen atoms combine together to make
oxygen molecule (O2).
In an oxygen molecule, each oxygen atom has two lone pair
2+2=4 bonded electrons
of electrons. When one more oxygen atom comes to join with
••
two lone pairs of
the oxygen molecule, one of the oxygen atoms from the
O
•• •• /
electrons
oxygen molecule donates one lone pair of electrons to the
third oxygen atom to complete octet of the third atom. So, in ozone molecule, there are
two types of bonds. They are covalent bond and coordinate bond.
/o•.. . _
.0.. ~o's.o....
.. ./Co~0..·.
..o.
Resonance
•
•
fig:Ozone resonance structures
fig:3D structure of ozone molecule
The actual structure of ozone is angular with O-O-O bond angle of 116.80. But, for our
convenient, we consider the structure of ozone linear planar. Actually, the double bond
of the ozone molecule can be found between any two oxygen atoms with the central
atom. Therefore, the structure of an ozone molecule is a resonance structure in which two
possible structures are present.
Fact with reason
Ozone is a coordinate covalent compound. Why?
Ozone molecule has three oxygen atoms. Among these atoms, there is one covalent
double bond between any two oxygen atoms and one coordinate bond between one
of the covalent bonding oxygen atoms and the third oxygen atom. So, ozone is a
coordinate covalent compound.
0
190
Optional Science - 10
C HEMI S TRY
Memory Plus
Abundant amount of ozone molecules are present in the stratosphere making ozone layer.
b. Structure of sulphur trioxide molecule (SO3)
Sulphur trioxide is a molecule which contains one sulphur and three oxygen atoms. The
electronic configuration of sulphur atom is 2, 8, 6 and oxygen atom is 2, 6. According to the
above electronic configuration, there are six electrons in the valance shell of sulphur and
oxygen atoms. On the basis of octet rule, sulphur and oxygen atoms need two electrons
each to complete their octet. Now, one sulphur atom and one oxygen atom combine
together to make double covalent bond. In this structure, sulphur and oxygen both have
two lone pair of electrons in each atom. Later on, sulphur atom donates its both lone pair
of electrons to the two oxygen atoms making two coordinate bonding between two S-O
atoms. As a result, sulphur trioxide molecule is formed. In sulphur trioxide molecule,
there are two types of bonds. They are covalent bond and coordinate bond.
0
0
0
/ ,
I
< ,
11
0
0
~\
O
II
< )
O
/ s\
O
0
fig:sulphur trioxide resonance structures
fig:3D structure of sulphur trioxide molecule
The structure of sulphur trioxide is trigonal planar. The bond angle between O-S-O in
SO3 is 120 degrees. Since, the sulphur can form double bond between sulphur and oxygen
atoms, the SO3 have three possible structures called resonance structures.
Fact with reason
Sulphur trioxide is a coordinate covalent compound. Why?
In sulphur trioxide molecule there is one sulphur atom and three oxygen atoms. Among
these atoms, there is one covalent double bond between sulphur atom and one of the
oxygen atoms. Similarly, two coordinate bonds are present between one sulphur and two
oxygen atoms. So, sulphur trioxide is a coordinate covalent compound.
Avogadro’s Law
We have discussed different gas laws like Boyle's law, Charle's law, Graham's law, etc. in
class nine. They established the relation of temperature, pressure and volume of the gases.
The Boyle’s law gives the relationship between pressure and volume of a gas, Charles law
gives the relationship between temperature and volume of a gas and Graham law gives
the relationship between rate of diffusion and density. Similarly, Avogadro’s Law gives the
relationship between volume of a gas with its amount (moles). Thus, Avogadro’s law states
that, “under constant temperature and pressure, equal volumes of all gases contain equal
number of molecules.”
Memory Plus
All ideal gases follow Avogadro's Principle in all conditions of temperature and pressure
but real gases follow this principle only at high temperature and low pressure.
C HEMI S TRY
Optional Science - 10
191
Memory Plus
•
Under constant temperature and pressure, volume of a gas (V) is directly proportional
to the number of molecules (n). It means that V α n
•
Under constant temperature and pressure, molar mass of all gases contain equal
number of molecules i.e. 6.022×1023 and equal volume i.e. 22.4 litres.
Mathematical derivation of Avogadro’s Law
V1
Take a balloon and fill a certain amount of gas (say n1 mol) into the
balloon. Suppose the volume of gas in the balloon is V1. Now, what
happens to the volume of air inside the balloon if more air is blown
into it? Yes, the volume of air increases inside the balloon. Similarly,
if we release the neck of the balloon gently to let air release out of the
balloon, the volume of air decreases. Thus, if we blow more air into the
balloon, there will be more volume of the gas and vice versa. It shows
that, the volume of a gas (V) is directly proportional to the amount of
gas (n).
i.e. V α n
or, V = nk where 'k' is a proportionality constant.
V2
n1
n2
V1
V2
n1
n2
V
=k
n
Let, us consider a sample of gas has volume V1 and amount of gas n1. If the amount of gas is
increased to make n2, then the volume of the gas also becomes V2. Then, we know that,
V1
---------- (i)
= k
n1
i.e.
V2
= k
---------- (ii)
n2
Equating equations (i) and (ii),
V2
V1
=
n2
n1
Explanation of Avogadro’s Law
Take equal volume of three gases like hydrogen (H2),
nitrogen (N2) and oxygen (O2) at equal temperature
and pressure. If we take molar mass of these gases,
then hydrogen contains 2g, nitrogen contains 28 g
and oxygen contains 32 g. At STP the molar mass
of these gases contain equal volume i.e. 22.4 litres.
The molar mass of these gases also contain equal
number of molecules i.e. 6.022 × 1023.
Using the above relationship between volume and
amount of substance, we have
0
192
Optional Science - 10
C HEMI S TRY
1mol
1mol
22.4 litres
0
6,022 x 1023 molecules
1mol
V1
n1
V1
i.e.,
1 mol
or,
V2
=
=
n2
=
V3
n3
V2
1 mol
=
V3
1 mol
V1 = V2 = V3 = 22.4 litre
From the above explanation, we can conclude that:
i.
At STP 1 mole of Hydrogen gas = 2 g = 22.4 litres= 6.022 × 1023molecules.
ii.
At STP 1 mole of Oxygen gas = 32 g = 22.4 litres = 6.022 ×1023molecules.
iii. At STP 1 mole of Nitrogen gas = 28 g = 22.4 litres = 6.022 × 1023molecules.
iv. At STP 1 mole of Carbon dioxide gas = 44 g = 22.4 litres = 6.022 × 1023molecules and so on.
Memory Plus
The volume occupied by one mole of an ideal gas is called molar volume. It is 22.4 litres.
Example: 1
A sample of 1.3 mole of gas has volume 10 litres. Calculate the amount of gas present in 20
litres if pressure and volume are kept constant.
Solution: Given,
Initial volume of the gas (V1)= 10 litres
Initial amount of gas (n1) = 1.3 mole
Final volume of the gas (V2) = 20 litres
Final amount of the gas (n2) = ?
According to Avogadro’s Law
V2
V1
=
n2
n1
Or, V1n2 = V2n1
Or, 10 × n2 = 20 × 1.3
20× 1.3
n2 =
mole
10
n2 = 2.6 mole
Or,
Or, The final volume of the gas is 2.6 moles.
Example: 2
How many molecules are present in 10 litres of carbon dioxide at STP?
Solution: Given,
Volume of carbon dioxide at STP (V)= 10 litres
Number of molecules = ?
According to Avogadro’s Law
C HEMI S TRY
Optional Science - 10
0
193
22.4 litres of carbon dioxide at STP = 6.022 × 1023molecules
6.022× 1023
or, 1 litres of carbon dioxide at STP =
molecules
22.4
6.022× 1023
× 10 molecules
or, 10 litres of carbon dioxide at STP =
22.4
10 litres of carbon dioxide at STP = 2.69 × 1023molecules
Example: 3
Calculate the volume of 5 mole of oxygen gas at STP.
Solution: Given,
Amount of oxygen gas (n) = 5 mole
Volume of oxygen (V) = ?
According to Avogadro’s Law,
1 mole of oxygen gas occupies = 22.4 litres volume
5 moles of oxygen gas occupies = 5× 22.4 litres = 112 litres
The volume of 5 mol of oxygen gas is 112 L.
Example: 4
How much gram of oxygen gas is present in 90 litres of oxygen at STP?
Solution: Given,
Volume of oxygen gas (V) = 90 litres
Amount of oxygen = ?
According to Avogadro’s Law,
1 mole of oxygen gas= 22.4 litres = 32 grams of oxygen
Form the above relation,
or, 22.4 litres = 32 grams of oxygen
32
or, 1 litre =
grams of oxygen
22.4
or, 90 litres =
32
× 90 grams of oxygen
22.4
= 128.57grams of oxygen
The 90 litres of oxygen contains 128.57 grams of oxygen
Answer writing skill
1.
What is chemical bonding? Write down the three types of chemical bonds.
Ans: The force of attraction which binds two or more elements together to make a stable
chemical compound is called chemical bonding. Mainly there are three types of chemical
bonding. They are:
i. Ionic or Electrovalent Bond
0
194
ii. Covalent Bond
Optional Science - 10
C HEMI S TRY
iii. Coordinate Bond
2.
Define electrovalent bond, covalent bond and coordinate bond.
Ans: The chemical bond which is formed in between metal and non-metal as a result of
transfer of electrons is called electrovalent bond. The chemical bond which is formed
by mutual sharing of electrons in between two or more non-metal atoms is called
covalent bond. Similarly, the type of chemical bond in which one of the combining
atoms contributes both of the shared electrons is called coordinate bond.
3.
What are electrovalent compounds, covalent compounds and coordinate compounds?
Write down any two examples of each.
Ans: The chemical compounds which are formed as a result of electrovalent bonding are
called electrovalent compounds or ionic compound. Examples: NaCl, MgCl2
The chemical compounds which are formed as a result of covalent bonding are called
covalent compounds. Examples: H2O, NH3
Those chemical compounds which are formed as a result of coordinate bonding are
called coordinate compounds. Examples: O3, SO3
4.
State Avogadro’s Law. Write down the relation among molar mass, number of
molecules and volume of the gas.
Ans: According to Avogadro’s law, under constant temperature and pressure, equal volumes
of all gases contain equal number of molecules. In a molar mass of a gas, the number of
molecules is 6.022 1023and volume is 22.4 litres.
5.
SO3 and O3 are called coordinate covalent compounds. Why?
Ans: The molecules SO3 and O3 contain both covalent and coordinate bonds. So, they are
called coordinate covalent compounds.
6.
Write any two differences between sigma bond and pi bond.
S.N. Sigma bond
7.
1.
Sigma bond is formed by end to end 1.
overlapping of the atomic orbitals.
Pi bond is formed by side to side
overlapping of the atomic orbitals.
2.
It is formed between s and s orbitals, 2.
p and p orbitals and s and p orbitals.
It is formed between p and p orbitals.
Write any two differences between NaCl and CH4.
S.N. NaCl
S.N. CH4
1.
2.
1.
2.
I
8.
S.N. Pi bond
NaCl is an electrovalent compound.
It has high melting and boiling point.
I
I
CH4 is a covalent compound.
It has low melting and boiling point.
I
Write down any three characteristics of each electrovalent and covalent compounds.
(a) Characteristics of electrovalent compounds
i.
Electrovalent compounds are formed as a result of electrovalent bonding.
ii. They have high melting and boiling point.
iii. They are strong chemical compounds as there is strong electrostatic force of
attraction.
C HEMI S TRY
Optional Science - 10
0
195
(b) Characteristics of covalent compounds
i.
Covalent compounds are formed by covalent bonding.
ii. They have low melting and boiling point as compared to the electrovalent
compounds.
iii. They are weaker than electrovalent compounds.
9.
In a balloon, 2.5 litres of helium gas is filled at STP. Calculate its mass?
Solution: Given,
Volume of helium = 2.5 litres
Mass of helium = ?
We know that,
22.4 litres of helium = 2 g helium
2
1 litre of helium =
grams of helium
22.4
2.5 litres of helium =
2
× 2.5 grams of helium
22.4
= 0.22 grams of helium
The 2.5 litres of helium contains 0.22 grams of helium
10.
Describe the formation and structure of sodium chloride (NaCl) molecule.
Ans: Sodium chloride (NaCl) is an example of electrovalent compound. It is formed by
combining sodium metal and chlorine non-metal. Sodium has electronic configuration
2, 8, 1 and chlorine has electronic configuration 2, 8, 7. According to octet rule, the
above electronic configuration shows that, sodium has one extra electron and chlorine
requires one more electron to attain stable electronic configuration. Thus, in order
to make sodium chloride, sodium loses one electron and makes sodium ion (Na+).
Similarly, chlorine gains one electron and makes chloride ion (Cl-). In between these
opposite ions there occurs a force of attraction called electrostatic force of attraction or
electrovalent bond. As a result, sodium and chloride combine together to give sodium
chloride (NaCl) molecule.
—e—
Na2, 8, 1 → Na+2, 8
+ e—
Cl2, 8, 7 →Cl–2, 8, 8
---____/
~~7~
Na
Sodium atom
NaCl
Cl
Chlorine atom
C®G
Na+
c1-
Sodium Ion
Chloride Ion
Sodium chlor ide (NaCl)
Na·
=Cl=
s22s22pe3523':i
1s2 2s2 2p63s; ...1
_________
'
196
Na+
1s22s22p6
Optional Science - 10
C HEMI S TRY
=Cl~
1s2 2s22p6 3s2 3p6
Exercise
Step
1.
1
Define the following terms.
i.
Bond
ii. Octet iii. Octet rule
iv. Duplet v. Electrovalent bond
vi. Covalent bond
vii. Coordinate bond
viii. Avogagro's Principle
ix. Duplet rule
2.
Write any four examples of the chemical compounds which have electrovalent bond.
3.
Mention any four examples of the chemical compounds which have covalent bond.
4.
Write down any two examples of the chemical compounds which have coordinate bond.
5.
Separate the following into electrovalent, covalent and coordinate compounds.
i. NaCl ii. MgCl2 iii. CaO
iv. NH3
v. CH4 vi. O3
vii. SO3
viii. H2 ix. N2
Step
1.
2
Differentiate between:
i.
Electrovalent bond and covalent bond
ii.
Electrovalent compounds and covalent compounds
iii. Sigma bond and pi bond
iv. Structure of NaCl and CH4
2.
Give reason.
i.
Except inert gases other elements are chemically unstable.
ii.
Inert gases are chemically stable.
iii. Electrovalent bond is also called ionic bond.
iv. Sodium chloride is an electrovalent compound.
v.
Magnesium chloride is an electrovalent compound.
vi. Calcium oxide is an electrovalent compound.
C HEMI S TRY
Optional Science - 10
197
vii. Water (H2O) is a covalent molecule.
viii. Methane (CH4) is a covalent molecule.
ix.
Ammonia (NH3) is a covalent molecule.
x.
Sulphur trioxide is a coordinate covalent compound.
3.
What are electrovalent compounds? Write any four examples.
4.
Define covalent compounds and write down any two examples.
5.
What are coordinate compounds? Write any two examples.
Step
1.
3
What are covalent compounds? Write down any four characteristics of the covalent
compounds.
2.
Define electrovalent compounds and write down any four characteristics of the
lectrovalent compounds.
3.
What are Sigma and Pi bonds? How are they formed?
4.
Explain in short about the formation of hydrogen molecule (H2)
5.
How is oxygen molecule (O2) formed? Describe in short.
6.
Describe in short about the formation of nitrogen molecule (N2).
7.
A sample of 2.6 mole of gas has volume 20 litres. Calculate the amount of gas present in
40 litres if pressure and volume are kept constant.
8.
How many molecules are present in 5 litres of carbon dioxide at STP?
9.
Calculate the volume of 10 mole of oxygen gas at STP.
10.
How much gram of oxygen gas is present in 30 litres of oxygen at STP?
11.
In a balloon, 4.0 litres of helium gas is filled at STP. Calculate its mass?
Step
1.
4
Describe the formation of the following molecules with the help of diagrams.
i.
NaCl ii. MgCl2 iii. CaO
iv. NH3 v. CH4 vi. O3
vii. SO3
V2
V1
=
State Avogagro's Principle and derive the relation
n2
n1
Describe an activity to prove that volume of a gas is directly proportional of its mass.
2.
3.
0
198
Optional Science - 10
C HEMI S TRY
Multiple Choice Questions
1.
2.
3.
4.
5.
6.
7.
8.
9.
10
Electrovalent bond is formed between
a. Metals and metals
b. Metals and non-metals
c. Non-metal and non-metal
d. None of the above
Covalent bond is formed between
a. Metals and metals
b. Metals and non-metals
c. Non-metal and non-metal
d. None of the above
What type of bond is present between H and H in H2 ?
a. Covalent bond
b. Ionic bond
c. Coordinate covalent bond
d. Both a and b
What type of bond is present between Ca and O in CaO?
a. Covalent bond
b. Ionic bond
c. Coordinate bond
d. None
What type of chemical compound is MgCl2 ?
a. Covalent compound
b. Ionic compound
c. Coordinate compound
d. None of the above
Sigma bond is formed by the overlapping between:
a. s and s orbitals
b. s and p orbitals
c. p and p orbitals
d. All of the above
Pi bond is formed by the overlapping between
a. s and s orbitals
b. s and p orbitals
c. p and p orbitals
d. All of the above
How many Pi bonds are present in HC ≡ CH?
a. 1
b. 2
c. 3
d. 4
How many molecules are there in 2 g of H2 gas?
a. 6.022 ×1027molecules
b. 6.022 ×1023 molecules
c. 6.022 ×1025molecules
d. 6.022 ×1024 molecules
How much volume is present in 32g of O2 gas?
a. 22.2 litres
b. 22.3 litres
c. 22.4 litres
d. 22.5 litres
C HEMI S TRY
Optional Science - 10
199
UNIT
10
ELECTROCHEMISTRY
About the inspiring personality
Svante Arrhenius was born on February 19, 1859, in Vik, Sweden and died on October 2,
1927. Arrhenius propounded many theories in chemistry, astronomy, earth’s ecology, etc.
He described Arrhenius theory of ionization.
...........................................................................................................................................................................................................................:
Syllabus issued by CDC
Ionic product of water
Introduction to pH and pOH along
with their numerical problems.
pH meter and pH range
Application of the neutralization
reaction (soil test, treatment of
acidity, treatment of insect bite)
•
•
•
•
Learning objectives:
After completing the study of this unit, students
will be able to:
• Explain the ionic product of water.
• Describe pH and pOH along with the
numerical problems.
• Describe pH meter and pH range.
• Explain the application of the neutralization
reactions in soil test, use of antacid, biting of
insects, etc.
Key terms and terminologies of the unit
1.
Electrochemistry: Electrochemistry is a branch of physical chemistry which deals
with relationship between chemical energy and electrical energy and how one is
converted into another.
2.
Ionic product of water (Kw): The product of molar concentration of hydrogen ion
(H+) and hydroxide ion (OH–) produced by self-ionization of water at a particular
temperature is called ionic product of water.
3.
pH: The negative logarithm of molar concentration of hydrogen ions is called pH.
4.
pH scale: The scale of hydrogen ions concentration which is used to express acidic
and basic strength of an aqueous solution is called pH scale.
0
200
Optional Science - 10
C HEMI S TRY
5.
pOH : The negative logarithm of molar concentration of hydroxyl ions is called pOH.
6.
pOH scale: The scale of hydroxyl ions concentration which is used to express acidic
and basic strength of an aqueous solution is called pOH scale.
7.
pH meter: The scientific device which is used to measure the exact pH value of a
solution without colour matching in the pH chart is called pH meter.
8.
Neutralization reaction: The chemical reaction in which an acid loses its acidic
property and the base also loses its basic property to give neutral products is called
neutralization reaction.
Introduction
In 1800 AD Volta had performed an experiment by passing current in water. As a result, he
found bubbles of hydrogen gas from the cathode and bubbles of oxygen gas from anode. Here,
electric current split water into hydrogen and oxygen gases. This process is called electrolysis
and water is called an electrolyte. Similarly, in various physical and chemical processes,
electricity is either consumed or produced. Different types of chemical reactions occur in
solution state. For example: neutralization reaction or acid base reaction, chemical reactions in
simple cell, battery, etc. Similarly, some chemical reactions also occur by passing electricity in
the solution. For example: electrolysis, electroplating, electro-refining, electrotyping, etc. These
chemical reactions are studied in a separate branch of chemistry called electrochemistry. Thus,
electrochemistry is a branch of physical chemistry which deals with relationship between
chemical energy and electrical energy and how one is converted into another. In this unit,
we will discuss about the nature of water, pH and pOH and application of neutralization
reactions in our daily life.
Ionic Product of Water
Water is a universal solvent. It dissolves most of the chemical substances
in it. Pure water is a weak electrolyte. It is neutral with pH value 7.0. It
undergoes very less ionization in normal temperature and pressure. Water
undergoes self-ionization into opposite
Ion ization
ions. After ionization, water produces
-------;>
H
+
hydrogen ion (H+) and hydroxide ion
(OH-).This self-ionization of water can be
Hydroxyl ion
Hydrogen ion
Water mol ecule
[H•)
[OHl
[H2 0 I
written as: H2O ⇋H+ + OH-
Memory Plus
We know that hydrogen ion is very reactive species. It reacts further with water molecule
to form hydronium ion(H3O+).
H2O + H+ H3O+
By applying the law of mass action, the ionization constant of water (K) can be given as:
[H+][OH—]
K =
[H2O]
or, [H+][OH-] = K×[H2O]
C HEMI S TRY
Optional Science - 10
0
201
As we have discussed that, water is a very weak electrolyte. It undergoes very less ionization
to give hydrogen ion and hydroxyl ion. As a result, the concentration of non-dissociate water
molecules [H2O] is more or less constant. Therefore, the product of ionization constant of
water (K) and concentration of water [H2O] gives another constant. This constant is called
ionic product of water (Kw).
Kw= [H+][OH-]
The product of molar concentration of hydrogen ion (H+) and hydroxide ion (OH-) produced
by self-ionization of water at a particular temperature is called ionic product of water.
Memory Plus
Derive the relation of ionic product of water.
Water undergoes self-ionization into opposite ions. As a result, it produces hydrogen ion
(H+) and hydroxide ion (OH-).
This self-ionization of water can be written as:
H2O ⇋ H+ + OHBy applying the law of mass action, the ionization constant of water (K) can be written as:
[H+][OH—]
K =
[H2O]
or, [H+][OH-] = K×[H2O]
Kw= [H+][OH-]
Here, Kw is called ionic product of water. It is the product of ionization constant of water
(K) and concentration of water [H2O].
Water behaves like an acid as well as a base. This is because water undergoes self-ionization
to give hydrogen ion(H+) and hydroxide ion (OH-). The substance which increases the
concentration of hydrogen ion (H+) makes water acidic and the substance which increases
the concentration of hydroxide (OH-) ion makes water basic. However, the pure water always
produces equal amount of hydrogen ion concentration and hydroxide ion concentration.
Thus, the product of molar concentration of hydrogen ion (H+) and hydroxide ion(OH-)
produced by self-ionization of water at a particular temperature is called ionic product of
water. The symbol of ionic product of water is Kw. The value of ionic product of water (Kw)
depends upon temperature. Kw increases with increasing temperature and decreases with
decreasing temperature. Therefore, the concentration of H+ and OH- ions increases with
increasing temperature and decreases with decreasing temperature. The value of Kw at
different temperature is given in the table.
Temperature
0°C
10°C
20°C
25°C
40°C
60°C
100°C
202
The value of Kw
0.11 × 10-14
0.31 × 10-14
0.86 × 10-14
1.00 ×10-14
2.91 × 10-14
9.61 × 10-14
7.50 × 10-14
Optional Science - 10
C HEMI S TRY
From the above table, it is clear that the value of Kw at 25°C is 1 x 10-14. As pure water is neutral
in nature, after auto-ionization the concentration of hydrogen ion [H+] and concentration of
hydroxyl ion [OH-]must be equal.
[H+] = [OH-] = x
or, [H+][OH-] = x2 = 1 × 10-14 at 25°C temperature
or, x = 1 × 10-7 mol/liter
or, [H+] = [OH-] = 1 × 10-7 mol/ liter
Memory Plus
The value of ionic product of water (Kw) at 25°C is 1 x 10-14.
As we have discussed that pure water produces equal amount of hydrogen ion and hydroxyl
ion. Addition of outer substance increases or decreases their concentration. When an acid or
a base is added to water, the ionic concentration product [H+][OH-] remains constant and it
becomes equal to Kw. Meanwhile the concentrations of H+ and OH- ions do not remain equal.
For example, the addition of acid increases the hydrogen ion concentration and decreases the
hydroxyl ion concentration.
So, for acid solution[H+] > [OH-]
or [H+] > 1 × 10-7 mol/l
Similarly, when a base is added to the water, the hydroxyl ion concentration [OH- ] increases
and hydrogen ion concentration [H+] decreases.
So, for alkaline solution [OH-] > [H+]
or, [OH-] > 1 × 10-7 mol/l
From the above discussion it is clear that, if hydrogen ion concentration is more than 1× 10-7 mol/l,
the solution becomes acidic. Similarly, if hydrogen ion concentration is less than 1 × 10-7 mol/l,
the solution becomes alkaline and if hydrogen ion concentration is equal to 1 × 10-7 mol/l, the
solution becomes neutral.
The different values of hydrogen ion concentration and the nature of the solution is given in
the table.
The value of hydrogen ion concentration [H+]
10 , 10 , 10 , 10 , 10 , 10 , 10
10-7 10-14, 10-13, 10-12, 10-11, 10-10, 10-9, 10-8
-0
-1
-2
-3
-4
-5
Nature of Water
Acidic
Neutral
Alkaline
-6
Similarly, the different values of hydroxyl ion concentration and the nature of the solution is
given in the table.
The value of hydroxyl ion concentration [OH-]
0-14, 10-13, 10-12, 10-11, 10-10, 10-9, 10-8 10-7 10-0, 10-1, 10-2, 10-3, 10-4, 10-5, 10-6 C HEMI S TRY
Nature of Water
Acidic
Neutral
Alkaline
Optional Science - 10
0
203
At 25°C temperature, the product of concentration of hydrogen ion and hydroxyl ion is
always constant and it is equal to 1×10-14 mol/l. If hydrogen ion concentration is more, then
the hydroxyl ion concentration will be less. From the above discussion, it is clear that every
aqueous solution contains both H+ and OH- ions and the product of their concentrations is
always constant, i.e., equal to 1 × 10-14 .
For example:
If [H+] = 10-3 mol/l, then [OH-] = 10-11 mol/l
Thus, the product of [H+][OH-] = 10-3 × 10-11 = 10-14
As hydrogen ion concentration is more than 10-7 mol/l , the solution is acidic.
Similarly, if [H+] = 10-12 mol/l, then [OH-] = 10-2 mol/l
Thus, the product of [H+][OH-] = 10-12 × 10-2 = 10-14
As hydrogen ion concentration is less than 10-7 mol/l , the solution is alkaline.
Fact with reason
Hydrochloric acid increases hydrogen ion concentration in water. How?
Hydrochloric acid ionizes in water to give hydrogen ion and chloride ion. Since it
produces hydrogen ion in water the concentration of hydrogen ion increases in water.
pH and pOH of a solution
Normally, there are three types of solutions. They are acidic solution, basic solution and neutral
solution. The nature of a solution is expressed in terms of hydrogen ions concentration. As we
know that pure water is a weak electrolyte, it produces very less concentration of hydrogen
ion and hydroxyl ion in the solution. So, it is very difficult to express in the general number. To
remove the difficulty, Sorensen in 1909 AD, introduced the popular term called pH and pOH.
pH
We know that strong acids undergo almost complete ionization to give a large amount of
hydrogen ion concentration and weak acids undergo very less ionization. The nature of the
solution, i.e. acidity, alkalinity or neutral can be expressed in terms of the hydrogen ions
concentration [H+]. The measure of hydrogen ions concentration present in a given solution
is called pH.
In the solution, the concentration of hydrogen ions is very small. It is inconvenient to use.
So, mathematically, it is expressed as a negative power to the base 10. Thus, the negative
logarithm of molar concentration of hydrogen ions is called pH. Form the above definition, it
is clear that,
pH = -log[H+]
In pure water, the molar concentration of hydrogen ions is 1 × 10-7 mol/l at 25°C. Thus, the pH
of pure water can be expressed as,
pH = -log[H+]
pH = -log[10-7 ]
=7
0
204
Optional Science - 10
C HEMI S TRY
Memory Plus
More hydrogen ions concentration indicates less pH value and less hydrogen ions
concentration indicates more pH value.
Therefore, the pH value of pure water is 7. This pH value also indicates that the solution is
neutral. In a given solution, if molar concentration of hydrogen ions is more than 10-7 mol/l, or
pH value less than 7, it indicates that the given solution is acidic in nature. Similarly, in a given
solution if molar concentration of hydrogen ions is less than 10-7 mol/l, or pH value more than
7, it indicates that the given solution is alkaline in nature.
If pH value is equal to seven It is a neutral solution
If PH value is less than seven It is an acidic solution
If pH value is more than seven It is an alkaline solution
pH Scale
An acidic solution has more hydrogen ions concentration and a basic solution has more
hydroxyl ions concentration. The relation between hydrogen ions concentration and pH value
is just opposite to each other. More hydrogen ion concentration means less pH value and viceversa. Therefore, to express the nature of solution in terms of hydrogen ions concentration,
a simple, convenient but standard scale is introduced. It is called pH scale. Thus, the scale of
hydrogen ions concentration which is used to express acidic and basic strength of an aqueous
solution is called pH scale.
pH scale is calibrated from zero to fourteen. The middle point of this scale is seven. It is a
neutral point and it indicates a neutral solution. The pH value more than seven indicates that
the solution is alkaline and the pH value less than seven indicates acidic solution. The pH
value zero is for the strongest acid and pH value fourteen is for the strongest base.
pH=0 pH=1 pH=2 pH=3 pH=4 pH=5 pH=6 pH=7 pH=8 pH=9 pH=10 pH=11 pH=12 pH=13 pH=14
Acidic solution
Neutral solution
Basic solution
Example: 1
Calculate pH of a solution whose hydrogen ions concentration is 10-2 mol/l.
Solution: Given,
Hydrogen ions concentration = 10-2 mol/l.
pH value = ?
Now, pH = -log[H+]
pH = -log[10-2 ]
=2
Example: 2
An aqueous solution of sulphuric acid has hydrogen ions concentration 10-2 mol/l. Calculate
its pH.
C HEMI S TRY
Optional Science - 10
0
205
Solution:
Given,
Hydrogen ions concentration = 10-2 mol/l.
pH value = ?
Now, pH = -log[H+]
pH = -log[10-2 ]
=2
Memory Plus
In pH, the p stands for potenz. It is a German word meaning power. Thus, pH indicates
power of hydrogen ion concentration.
pOH
We have discussed that, pH value of a neutral solution is 7. If pH value increases from 7 to
14, it represents an increase of hydroxyl ion concentration in the solution. So, similar to the
pH scale, the acidic and basic strength of an aqueous solution can also be represented in term
of hydroxyl ions concentration (OH-). Thus, the negative logarithm of molar concentration of
hydroxyl ions is called pOH. Form the above definition, it is clear that,
pOH = -log[OH-]
In pure water, the molar concentration of hydroxyl ions is 1 × 10-7 mol/l at 25°C. Thus, the pOH
of pure water can be expressed as,
pOH = -log[OH-]
pOH = -log[10-7 ]
= 7
Therefore, the pOH value of pure water is 7. This pOH value also indicates that the solution
is neutral. In a given solution, if molar concentration of hydroxyl ions is more than 10-7 mol/l,
or pOH value less than 7, it indicates that the given solution is alkaline in nature. Similarly, in
a given solution if molar concentration of hydroxyl ions is less than 10-7 mol/l, or pOH value
more than 7, it indicates that the given solution is acidic in nature.
If pOH value is equal to seven It is a neutral solution
If POH value is less than seven It is an alkaline solution
If pOH value is more than seven It is an acidic solution
pOH Scale
A basic solution has more hydroxyl ions concentration and an acidic solution has less hydroxyl
ions concentration. The relation between hydroxyl ions concentration and pOH value is just
opposite to each other. More hydroxyl ion concentration means less pOH value and viceversa. Therefore, to express the nature of solution in terms of hydroxyl ions concentration, a
simple, convenient but standard scale is introduced. It is called pOH scale. Thus, the scale of
hydroxyl ions concentration which is used to express acidic and basic strength of an aqueous
solution is called pOH scale.
206
Optional Science - 10
C HEMI S TRY
pOH scale is calibrated from 0 to fourteen. The middle point of this scale is seven. It is a
neutral point and it indicates a neutral solution. The pOH value more than seven indicates
that the solution is acid and the pOH value less than seven indicates basic solution. pOH value
zero is for the strongest base and pOH value fourteen is for the strongest acid.
pOH pOH pOH pOH pOH pOH pOH pOH pOH pOH pOH pOH
=0
=1
=2
=3
=4
=5
=6
=7
=8
`= 9 = 10 = 11
Basic solution
Neutral solution
pOH
= 12
pOH
= 13
pOH
= 14
Acid solution
Example: 1
Calculate pOH of a solution whose hydroxyl ions concentration is 10-3 mol/l.
Solution: Given, Hydroxyl ions concentration = 10-3 mol/l
pOH = ?
Now, pOH = -log[OH-]
pOH = -log[10-3 ]
=3
Therefore, the solution is basic in nature.
Example: 2
Calculate pOH of an aqueous solution of potassium hydroxide whose hydroxyl ions
concentration is 10-2 mol/l.
Solution: Given, Hydroxyl ions concentration = 10-2 mol/l
pOH = ?
Now, pOH = -log[OH-]
pOH = -log[10-2 ]
=2
Therefore, the solution is basic in nature.
Relation between pH and pOH
Pure water undergoes auto-ionization to give hydrogen ion and hydroxyl ion. From these
hydrogen and hydroxyl ions, we can express ionic product of water.
H2O ⇋H+ + OH-
[H+] [OH-] = Kw
We know that at 25°C, the value of Kw is 10-14
Taking -log on both sides of the equation, we have,
- log [H+] +(- log [OH- ]) = - log [Kw ]
- log [H+] +(- log [OH- ]) = - log [10-14 ]
pH + pOH = 14
The above expression is a relation between pH and pOH.
Therefore, for pure water the sum of pH and pOH is equal to 14. If a solution has pH value 3
than the pOH value will be 11.
C HEMI S TRY
Optional Science - 10
0
207
Example: 1
Calculate pOH of a solution whose hydrogen ions concentration is 10-3 mol/l.
Solution: Given, Hydrogen ions concentration = 10-3 m/l
The value of pOH = ?
According to the formula,
pH =- log [H+]
pH =- log [10-3 ]
pH = 3
Now, pH + pOH = 14
3 + pOH = 14
The value of pOH = 11
The solution has pH value less than 7 or pOH value more than 7. So, it is an acidic solution.
Example: 3
An aqueous solution of potassium hydroxide has hydroxyl ions concentration 10-2 mol/l.
Calculate pOH and pH value.
Solution: The hydroxyl ions concentration = 10-2 m/l.
The value of pOH = ?
The value of pH = ?
From the formula
pOH = -log[OH-]
pOH = -log[10-2 ]
=2
Now, pH + pOH = 14
pH + 2 = 14
pH = 12
Hence, the given solution is basic in nature as it has pH value more than 7 and pOH value
less than 7.
pH meter
The lab technician measures the pH value of different body fluids like blood, urine, etc. in the
pathology. A chemist measures pH value of different chemicals in the chemistry laboratory.
Similarly, a gardener or agriculturist measures the pH value of soil. While measuring pH value
of the different substances, it is necessary to find the exact value of pH. Generally, we use pH
paper to find their pH value. While measuring pH value through pH paper, the colour change
in pH paper is matched with the colour chart of the pH scale. The matching of colour of pH
paper with pH colour chart, it is very difficult to find the exact result. So, we use a scientific
device to measure the pH value of the solution. It is called pH meter. Thus, the scientific
device which is used to measure the exact pH value of a solution without colour matching in
the pH chart is called pH meter.
0
208
Optional Science - 10
C HEMI S TRY
The pH meter contains a rectangular box, pH rod and conducting wire.
While measuring the pH value of a given solution, the rod is dipped inside
the solution and the switch is turned on. After the switch turned on, the pH
value of the solution comes directly on the number.
The pH Value of Some Substances is given in the table
I
fig:pH meter
S.N. Substances or Compounds
pH
Hydrochloric acid (HCl)
Sulphuric acid (H2SO4)
Lemon juice
Juice of apples, vinegar and carbonic acid
Butter
Ethanol, water, salt and sugar solution
Human blood
Baking soda
Ammonium hydroxide (NH4OH)
Sodium carbonate or washing soda (Na2CO3)
Caustic soda or sodium hydroxide (NaOH)
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
1.0
1.2
2.5
3.0
6.0
7.0
7.3
8.5
10.0
11.5
13
Neutralization reaction
Take a test tube and put some amount of hydrochloric acid and sodium hydroxide. After their
reaction, we will get sodium chloride (NaCl) and water (H2O) called an acid-base reaction. As
a result of this reaction, acid and base lose their own properties. Hence,this reaction is also
called a neutralization reaction.
For example:
Acid + Base → Salt + Water
HCl + NaOH → NaCl + H2O
H2SO4 + KOH →K2SO4 + H2O
The chemical reaction in which an acid loses its acidic property and the base also loses its basic
property to give neutral products is called neutralization reaction. Normally, in neutralization
reaction, an acid and a base react together to form salt and water. The salt thus produced may
be acidic, basic or neutral depending upon the nature of the acid and base. The neutralization
actually involves the combination of H+ ions and OH- ions to produce water. The products of
neutralization reaction after the combination of a strong acid and a strong base have the pH
value 7. The neutralization products of a strong acid and a weak base have pH value less than
7. Similarly, when a strong base reacts with a weak acid, it gives the products having pH value
greater than 7. The above discussion can be summarized in the following box.
S.N.
Acid
Base
Resultant Salt
Resultant pH value
1.
Strong acid
Strong base
Neutral salt
pH value equal to 7
2.
Strong acid
Weak base
Acidic salt
pH value less than 7
3.
Weak acid
Strong base
Basic salt
pH value more than 7
4.
Weak acid
Weak base
Neutral salt
pH value equal to 7
(
(
C HEMI S TRY
l
Optional Science - 10
OJ
209
Memory Plus
The most common strong acids are HCl, H2SO4, HNO3, etc. Similarly, the strong bases are
LiOH, NaOH, KOH, RbOH, Ca(OH)2 Sr(OH)2, Ba(OH)2, etc.
i) The neutralization reaction between strong acid and strong base
HCl(aq) +NaOH(aq) ⇋ NaCl(aq) + H2O(l)
Observe the above chemical reaction between hydrochloric acid and sodium hydroxide. In
this reaction, hydrochloric acid is a strong acid and sodium hydroxide is a strong base. When
equal amount of hydrochloric acid and sodium hydroxide are mixed together, they give
sodium chloride and water. Sodium chloride is a neutral salt and water is a neutral liquid. So,
both have pH value seven. The ionic combination of this reaction can be expressed as:
H++Cl−+Na++OH−⇋ NaCl +H2O
ii) The neutralization reaction between weak acid and weak base
H2CO3(aq) +2 NH4OH(aq) ⇋ (NH4)2CO3(aq)+2H2O(l)
Observe the chemical reaction between carbonic acid (H2CO3) and ammonium hydroxide
(NH4OH). In this reaction, carbonic acid is a weak acid and ammonium hydroxide is a weak
base. When equal amount of carbonic acid (H2CO3) and ammonium hydroxide (NH4OH)are
mixed together, they give ammonium carbonate and water. The actual ionic combination of
this reaction is given below.
2H++CO3−− + NH4++OH−⇋ (NH4)2CO3(aq)+ H2O(l)
Here, ammonium carbonate is a neutral salt. Its aqueous solution has pH value seven. Similarly,
water is a neutral liquid with pH value seven. Thus, when a weak acid and a weak base fully
neutralize, the products have pH value 7.
Applications of the neutralization reaction
Soil Test
The top most fertile layer of the earth is called soil. We use soil to grow crops. There are
different kinds of crops which grow in the soil of different nature. We know that different
soil contain different kinds of nutrients. That is why the pH value of the soil is different in
different places. It is observed that the soil of a certain pH value is suitable for the healthy
growth and development of the plants. It would be better to grow the crops after knowing the
concentration of the nutrients and pH value of the soil. But, it is also found that the pH value
and the concentration of the nutrients change as we grow the same crop continuously for a
long time. The pH value also changes due to the different kinds of environmental pollutions,
such as acid rain, solid wastes, chemical fertilizers, etc. Therefore, it is necessary to test the soil
before sowing the crops.
Measurement of pH value of the Soil
In the pH scale, the pH value ranges from 0 to 14. The pH value seven represents neutral
solution. The pH value below seven represents acidity and pH value above seven represents
alkalinity. Zero pH value represents severe acidity and fourteen is an extreme alkalinity.
210
Optional Science - 10
C HEMI S TRY
Plants require a specific pH range for their healthy growth and development. The pH value of
a soil is the measure of its acidity and alkalinity. The pH of the soil in the crop-land should be
in the range of 6.0 to 7.5. If pH value becomes more or less than the specific range, it directly
affects the presence of nutrients in the soil. So, it is necessary to test the soil time and again
to find the pH value and concentration of the nutrients. If pH value changes, we need to add
certain chemicals to balance it. Similarly, if concentration of the nutrients changes, we need to
add organic or chemical fertilizers to maintain the concentration of the nutrients.
Memory Plus
The favourable pH range of the soil for the healthy growth and development of the plants
is 6.0 to 7.5
Neutralization of the soil
It is necessary to neutralize soil in order to promote the healthy growth and development of
the plants. The pH value of the surrounding soil affects the absorption of nutrients from the
soil into the roots of the plants. Different kinds of environmental pollution, solid wastes, acid
rain, etc. increase the acidity of the soil. The acid present in the soil must be neutralized by
using lime or calcium oxide (CaO). The process of adding lime to reduce acidity of the soil
is called liming. In the liming process, agricultural limestone, i.e. calcium carbonate (CaCO3)
along with some amount of magnesium carbonate (MgCO3) is used to neutralize acidity of
the soil. In some area, the soil becomes too basic. To reduce the alkalinity, we add some acid
substances such as calcium sulphate (CaSO4), sulphur (S2), etc. to the soil.
Memory Plus
The acidity of the soil is reduced by using agricultural limestone, i.e. calcium carbonate
(CaCO3) along with some amount of magnesium carbonate (MgCO3). Similarly, alkalinity
is reduced by adding calcium sulphate (CaSO4), sulphur (S2), etc.
Treatment of Hyper-acidity
Our stomach produces hydrochloric acid which helps in the digestion of food without harming
stomach. During indigestion, large amount of hydrochloric acid accumulates in the stomach.
This acid causes pain and irritation. It also causes heart burn, sour fluid vomiting, bombast,
etc. This problem can be solved by using bases present in the tablets called antacids. Antacids
contain aluminium hydroxide, magnesium hydroxides, magnesium carbonate, magnesium
trisilicate, etc. In the market, antacids are present in various brand-names. They are available
in tablets as well as in liquids. Some antacids are combined with another medicine called
simeticone which helps to reduce wind (flatulence).
Memory Plus
Antacids contain aluminium hydroxide, magnesium hydroxides (milk of magnesia),
magnesium carbonate, magnesium trisilicate, etc.
C HEMI S TRY
Optional Science - 10
0
211
Treatment of insect stings
Have you ever been stung by a honeybee? Bee-sting leaves an acid which causes pain and
irritation. This acid can be neutralized by using chemicals containing mild-base such as
sodium bicarbonate or baking soda. Similarly, wasp sting also injects alkaline venom in our
body. Since venom is alkaline in nature, baking soda does not work in this situation. In this
case, mild acids such as vinegar can relieve the pain.
Memory Plus
Bee-sting gets relief by using sodium bicarbonate and wasp sting by using vinegar.
Answer writing skill
1.
Define ionic product of water. Write down its equation.
Ans: The product of molar concentration of hydrogen ion (H+) and hydroxide ion (OH-)
produced by self-ionization of water at a particular temperature is called ionic product
of water. The equation of ionic product of water is Kw = [H+][OH-]
2.
What are pH and pOH scale?
Ans: The scale of hydrogen ions concentration which is used to express acidic and basic
strength of an aqueous solution is called pH scale. Similarly, the scale of hydroxyl ions
concentration which is used to express acidic and basic strength of an aqueous solution
is called pOH scale.
3.
What is the main difference between pH paper and pH meter?
Ans: pH paper is a device which is used to measure pH value of the solution comparing its
colour change with the colour chart. But, pH meter is a scientific device which is used to
measure the exact pH value of a solution without colour matching in the pH chart.
4.
What is acid base reaction? Why is it called a neutralization reaction?
Ans: The chemical reaction in which an acid reacts with base to give salt and water is called
acid-base reaction. In acid-base reaction, an acid loses its acidic property and the base
also loses its basic property to give neutral products. So, it is also called a neutralization
reaction.
5.
How does hyper acidity occur in our stomach? What can be done to relief it?
Ans: Our stomach produces hydrochloric acid which helps in the digestion of food without
harming stomach. During indigestion, large amount of hydrochloric acid accumulates
in the stomach causing heart burn, sour fluid vomiting, bombast, etc. This problem can
be solved by using mild bases present in the tablets or liquids called antacids. Antacids
contain aluminium hydroxide, magnesium hydroxides (milk of magnesia), magnesium
carbonate, magnesium trisilicate, etc.
212
Optional Science - 10
C HEMI S TRY
6.
Derive the relation to show that [H+] = [OH-] = 1 × 10-7 mol/ liter
Ans: At 25°C temperature, the value of ionic product of water (Kw) is 1 × 10-14. After selfionization, the concentration of hydrogen ion [H+] and concentration of hydroxyl ion
[OH-] must be equal.
Thus, [H+] = [OH-] = x
or [H+][H+] = x2
{Since, in value[H+] = [OH-] }
or [OH-][OH-] = x2
or, [H+][OH-] = x2 = 1 × 10-14 at 25°C temperature
or, x = 1 × 10-7 mol/l
or, [H+] = [OH-] = 1 × 10-7 mol/ liter
7.
Derive the relation between pH and pOH.
Ans: Pure water undergoes self-ionization to give hydrogen ion and hydroxyl ion. From these
hydrogen and hydroxyl ions, we can express ionic product of water.
H2O ⇋H+ + OH-
[H+] + [OH-] = Kw
We know that at 25°C, the value of Kw is 10-14
Taking -log on both sides of the equation,
We have,
- log [H+] +(- log [OH- ]) = - Kw [10-14 ]
- log [H+] +(- log [OH- ]) = - log [10-14 ]
pH + pOH = 14
8.
Write down any three application of the neutralization reaction.
Ans: The three applications of the neutralization reaction reactions are:
i.
The acidity of the soil is reduced by using agricultural limestone, i.e. calcium
carbonate (CaCO3) along with some amount of magnesium carbonate (MgCO3).
Similarly, alkalinity of the soil is reduced by adding calcium sulphate (CaSO4),
sulphur (S2), etc.
ii.
The hyperacidity in the stomach can be solved by using antacids which contain
aluminium hydroxide, magnesium hydroxides (milk of magnesia), magnesium
carbonate, magnesium trisilicate, etc.
iii.
Bee-sting gets relief by using sodium bicarbonate and wasp sting by using vinegar.
C HEMI S TRY
Optional Science - 10
0
213
9.
An aqueous solution of a compound has hydrogen ions concentration 10-2 mol/l.
Calculate its pH and pOH value. Also, mention its chemical nature.
Solution:
Given, Hydrogen ions concentration = 10-2 mol/l.
pH value = ?
pOH value = ?
Now, pH = -log[H+]
pH = -log[10-2 ]
=2
Again, pH + pOH = 14
2 + pOH = 14
pOH = 12
Here, pH value is less than 7 and pOH value is more than 7. So, the given chemical
compound is an acid.
10.
Describe an activity to test the pH value of the different soil samples.
Ans: i.
Collect different samples of soil from the different places.
ii.
Put about 2 g of soil in each test tube separately.
iii.
Put distilled water in each sample of soil and shake well.
iv.
Allow the solution for sedimentation.
v.
Filter the solution and separate the clear liquid.
vi.
Dip a pH paper in the clear solution.
vii. Match the colour change in the pH paper with the colour chart and find the pH
value of the soil sample.
0
214
Optional Science - 10
C HEMI S TRY
Exercise
1
Step
1.
Define the following terms.
Ionic product of water (Kw)
i.
ii. pH
iii. pH scale
iv. pOH
pOH scale
v.
vi. pH meter
vii. Neutralization reaction
2.
Very short answer questions
1.
What is pH range? Show in the pH scale.
2.
Write down the value of hydrogen ion concentration in pure water.
3.
Write down the equation for the ionic product of water.
4.
Write down the pH and pOH value of pure water.
5.
What happens when a strong acid reacts with a strong base?
6.
What kind of products can be obtained when weak acid reacts with a weak base?
7.
Write down the pH value of the products when strong acid reacts with strong base?
8.
What are antacids? Write down any two examples.
2
Step
1.
Give reason.
i.
Water is a neutral solution.
ii.
Hydrochloric acid increases hydrogen ion concentration in water. How?
iii.
Sodium hydroxide increases hydroxyl ion concentration in water. How?
C HEMI S TRY
Optional Science - 10
215
2.
Draw a pH scale showing acid, base and neutral range.
3.
What is pOH scale? Show with pOH scale.
4.
What is pH meter? Why is it better than pH paper?
5.
What treatment can be done in bee sting?
3
Step
1.
What is hyperacidity? Describe the process to reduce it.
2.
Write down any three application of the neutralization reaction.
3.
If the pH of a solution is 4, what is its pOH?
4.
Calculate pOH and pH value of aqueous solution of potassium hydroxide whose
hydroxyl ions concentration is 10-3 mol/l.
5.
Calculate pH and pOH of a solution whose hydrogen ions concentration is 10-4 mol/l.
6.
Calculate pOH and pH of a solution whose hydroxyl ions concentration is 10-3 m/l.
7.
Calculate pOH and pH of aqueous solution of calcium hydroxide whose hydroxyl
ions concentration is 10-3 mol/l.
4
Step
1.
What is pH meter? How does it work?
2.
Describe the importance of pH value of soil. How does pH value of soil change?
How can we balance the pH value of the soil?
3.
Derive the relation to show that H+] = [OH-] = 1 × 10-7 mol/ liter
4.
Derive the relation between pH and pOH.
5.
Describe an activity to test the pH value of the soil sample.
Multiple choice questions:
1.
The ionic product of pure water at 25°C is
a. 10-7 mol/l
2.
0
216
b. 10-14mol/l
c. 10-10mol/l
d. 10-5mol/l
What is the pH range of crop land?
a. pH 2 to 7
b. pH 6 to 8
c.
d. pH 6 to 7.5
pH 5.5 to 7.5
Optional Science - 10
C HEMI S TRY
3.
4.
What is the pOH value of pure water?
a. 1
b. 7
c. 14
pH is the measure of
d. 0
a. Percentage of water molecules b. Percentage of hydrogen atoms
5.
6.
7.
8.
9.
c. Percentage of hydroxyl ions
pOH is the measure of
d. Hydrogen ion concentration
a. Hydrogen ion concentration
b. Percentage of hydrogen atoms
c. Percentage of hydroxyl ions
d. Hydroxyl ion concentration
Which acid causes hyperacidity in the stomach?
a. Sulphuric acid
b. Nitric acid
c. Hydrochloric acid
Pure water is
d. Acetic acid
a. Slightly acidic
b. Slightly alkaline
c. Neutral
d. Highly acidic
Which chemical is added to reduce acidity of soil
a. Calcium sulphate
b. Calcium carbonate
c. Calcium nitrate
Which is an antacid?
d. Calcium borate
a. Sodium chloride
b. Lactic acid
c. Citric acid
10. Which is milk of magnesia
d. Magnesium hydroxide
a. Aluminium hydroxide,
b. Magnesium carbonate
c.
d. Magnesium hydroxide
Magnesium trisilicate,
Project Work
1.
Collect sample of soil from your surroundings and calculate their pH value
using pH paper and pH colour chart.
2.
Collect a citrus fruit and extract juice from it. With help of pH paper and pH
colour chart find out its pH value.
C HEMI S TRY
Optional Science - 10
217
UNIT
11
ORGANIC CHEMISTRY
·······················································---------. . . . . . . . .................................................... .
Vladimir Vasilyevich Markovnikovborn (in 1838 AD-1904) was born in Nizhny
Novgorod, Russia and died in Moscow. He formulated a theory called Markovnikov
addition theory. It is used in addition of hydrogen halides to the carbon-carbon double
bond or unsymmetrical alkenes.
• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •., • • • ••••• • - - - - - - u •- •••••••••• •• ., • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •
•
•
•
•
•
Syllabus issued by CDC
Learning objectives:
Introduction to organic reactions
* Substitution reaction
* Addition reaction
* Eliminationreaction
Electrophyles and nucleophyles
Types of chemical reactions
Markovnikov rule
Saytziff’s rules
After completing the study of this unit, students
will be able to:
* Introduce substitution reaction, addition reaction
and elimination reaction in organic chemistry.
• Explain electrophyles and nucleophyles.
• Explain markovnikov rule and Saytziff’s rules
Key terms and terminologies of the unit
1.
Organic chemistry: The branch of chemistry in which we study about structure,
properties, composition, reactions and preparation of the carbon-containing
compounds is called organic chemistry.
2.
Organic compounds: The chemical compounds which contain carbon as one of the
primary elements are called organic compounds.
3.
Organic reactions: Those chemical reactions which involve organic compounds and
production of organic compounds are called organic reactions.
4.
Substitution reactions: Those chemical reactions in which an atoms or groups of
atoms in a molecule are replaced by another atoms or groups of atoms are called
substitution reactions.
218
Optional Science - 10
C HEMI S TRY
5.
Addition reactions: Those chemical reactions in which atoms or groups of atoms are
added to the organic molecule which has one or more multiple covalent bonds are
called addition reactions.
6.
Elimination reactions: Those chemical reactions in which atoms or group of atoms
are eliminated from the organic molecules to give unsaturated product are called
elimination reactions.
7.
Nucleophiles: Nucleophile are atoms or groups of atoms which provide a pair of
electrons to form a new covalent bond.
8.
Electrophiles: Electrophiles are atoms or groups of atoms which accept a pair of
electrons to form a new covalent bond.
9.
Markovnikov's rule: According to Markovnikov's rule "when an unsymmetrical
alkene reacts with hydrogen halide to give an alkyl halide, the hydrogen adds to the
carbon of the alkene that has the greater number of hydrogen atoms and the halogen
to the carbon of the alkene with the fewer number of hydrogen atoms".
10.
Saytjeff’s rule: According to Saytjeff’s rule "the most substituted product is more
stable and is favoured over other products."
Introduction
In our surrounding we see different kinds of substances. These substances are called matter.
The study of physical and chemical properties of these matters is called chemistry. In chemistry
there are mainly three branches. They are physical chemistry, inorganic chemistry and
organic chemistry. In inorganic chemistry we study about inorganic substances, in organic
chemistry we study about organic substances and in physical chemistry we study about
physical properties of the organic and inorganic substances. Thus, the branch of chemistry
in which we study about structure, properties, composition, reactions and preparation of the
carbon-containing compounds is called organic chemistry. It has broad area. It covers not only
the compounds made up of hydrocarbon but also the compounds with other elements like,
nitrogen, oxygen, halogens, phosphorus, silicon, sulphur, etc.
Memory Plus
Urea is an organic compound and naturally it is produced in the kidneys of human beings.
HCl is produced in our stomach but it is an inorganic compound because it does not
contain carbon atom.
Previously, organic chemistry was limited to the chemical compounds which were produced
within the living organisms. But, after the formation of urea in the laboratory, organic
chemistry became a vast branch of science. This credit goes to the chemist Friedrich Wohler.
Now, organic chemistry covers the man-made compounds like monomers, polymers, plastics,
dyes, drugs, etc. and natural compounds like protein, carbohydrates, fat, vitamins, etc. So,
the range of application of organic compounds is very high. It includes pharmaceuticals,
petrochemicals, food, explosives, paints, cosmetics, textiles, etc. In this unit, we will discuss
about some organic compounds and the related chemical reactions.
C HEMI S TRY
Optional Science - 10
0
219
Organic compounds
The chemical compounds which contain carbon as one of the primary elements are called
organic compounds. It includes large number of chemical compounds like methane, ethane,
propane, alcohol, ether, carbohydrates, proteins, fat, vitamins, plastics, dyes, drugs, etc. But,
organic chemistry does not include some chemical compounds which contain carbon as one of
the elements. For example, carbides, carbonates, cyanides, etc. There are two types of organic
compounds. They are:
Memory Plus
Propane is known as acyclic compound because it has open chain of carbon atoms.
a.
Open chain or acyclic organic compounds
It includes those compounds which contain open chain of carbon atoms. For example,
methane, ethane, propane, butane, alcohol, ether, etc. They are also called aliphatic
compounds.
H
H
H
H
I I I
I
H- C - H
H-C-C-C-H
I
H
1
H
Methane
b.
I
H
I
H
Propane
Closed chain or cyclic compound
It includes those organic compounds which have closed ring of carbon atoms. For
example: cyclopropane, cyclobutane, cyclopentane, cyclohexane, etc. Cyclic compounds
are also known as ring compounds.
CH2
/\
H2C
CH2
Cyclopropane
H2C
CH2
I CH
I
H2C
H2C
I
H C
2
2
Cyclobutane
---
CH2
\
; CH2
CH2
Cyclopentane
Both acyclic and cyclic compounds have covalent bond. Thus, organic compounds must
have two properties. They are:
i. Organic compounds must have carbon atom as one of the elements.
ii. There must have covalent bond between the carbon atoms.
The organic compounds differ from inorganic compounds in many respects. Such
Fact
with reason
as composition,
isomerism, solubility, melting point, boiling point, etc. Some organic
Carbides,
carbonates,
cyanides,
etc. have
carbon formula,
atom butcondensed
they are called
inorganic
compounds
with molecular
formula,
structural
formula
and three
compounds.
Why?
dimensional
structures are given below.
. Carbides, carbonates, cyanides, etc. have carbon atom but they are called inorganic
compounds because they do not have covalent bond in them.
220
Optional Science - 10
C HEMI S TRY
Some of the organic compounds along with their molecular formula, structural formula,
condensed formula and the three dimensional structure are given below.
Organic
Molecular Condensed
structural formula
Compounds formula
ethane
C2H6
CH3CH3
butane
C4H10
CH3CH2CH2CH3
expanded
structural formula
3-D structural
formula
cyclohexane C6H12
ethene
C2H4
CH2
CH2
ethyne
C2H2
HC
CH
H—C
C—H
Uses of organic compounds
There are large number of natural and man-made organic compounds which are very
important for both plants and animals. They are the pillars to the economic growth of the
country. Economic growth becomes fast if the country can manufacture different kinds of
organic compounds like plastics, rubber, fuel, pharmaceutical, cosmetics, detergent, dyes,
agrochemicals, etc. Some of the major uses of the organic compounds are given below:
1.
Industrial use of organic compounds: Organic compounds are used for manufacturing
different kinds of organic materials like dynes, detergent, soap, fuel, plastic, rubber,
cosmetics, pharmaceutical goods, pesticides, fertilizers, etc.
2.
Domestic use of organic compounds: Large numbers of organic compounds are also
used in our home. For example: sugar, oil, ghee, etc.
3.
Medicinal use of organic compounds: Various organic compounds are used for the
treatment of diseases.
4.
Religious use of organic compounds: Some organic compounds are religiously very
important. For example: chandan plant is used as tika in Hindu religion.
5.
Laboratory use of organic compoundsSome organic compounds are used in the
laboratory as the laboratory reagents. They are used in chemical test, research, etc.
On the basis of use and study of organic compounds, the organic chemistry also has many
branches. For example: biochemistry, biotechnology, medicine, pharmaceutical, etc.
C HEMI S TRY
Optional Science - 10
221
Memory Plus
Nobel Prize was established in 1895 in name of Swedish chemist, engineer and inventor
Alfred Noble. It honors the people in six different fields. They are: chemistry, physics,
medicine, economics, literature and peace.
Organic Reactions
In inorganic chemistry we have studied various kinds of chemical reactions like addition
reaction, decomposition reaction, displacement reaction, neutralization reaction, etc. In
organic chemistry, we will study about addition reactions, elimination reactions, substitution
reactions, pericyclic reactions, rearrangement reactions, photochemical reactions, redox
reactions, etc. The production of many man-made chemicals such as drugs, plastics, food
additives, fabrics also depend up on organic reactions.
The chemical reactions which involve organic compounds and production of organic
compounds are called organic reactions. The organic reactions are divided into two groups.
They are basic organic reactions and advanced organic reactions. The earlier organic reactions
were combustion of organic fuels and saponification of fats to make soap. But, the modern
organic chemistry starts with the Wohler synthesis. In this synthesis, urea was formed by
the thermal decomposition of ammonium cyanide in the laboratory. The invention of some
organic reactions such as Grignard reaction , Diels-Alder reaction, Wittig reaction , olefin
metathesis, etc. have changed the history of organic chemistry. In this unit, we will study
about some basic organic reactions.
i. Substitution reaction
ii. Addition reaction
iii. Elimination reaction
Fact with reason
Wohler synthesis is considered as a milestone in the history of organic chemistry.
Why?
It is because Wohler synthesized urea in the laboratory from ammonium cyanide.
Thereafter, chemists denied the vital force theory of the organic compounds which was a
milestone in the history of chemistry and extend the area of organic chemistry.
i.
Substitution reactions
CH3-CH2-Cl +NaOH CH3-CH2-OH + NaCl
Observe the above chemical reaction. In this reaction, ethyl chloride reacts with sodium
hydroxide to give ethyl alcohol and sodium chloride. In this reaction, chlorine of ethane
is replaced by hydroxyl group of sodium hydroxide. Such type of reaction is called
substitution reaction. Those chemical reactions in which an atom or groups of atoms
in a molecule are replaced by another atoms or groups of atoms are called substitution
reactions. In substitution reaction, the saturation and unsaturation of the organic
compounds do not change. It means that unsaturated molecules remain unsaturated and
saturated molecules remain saturated after the reaction. For example:
0
222
Optional Science - 10
C HEMI S TRY
Example: 1
Ethanol (CH3CH2OH) reacts with hydrogen iodide (HI) to form iodoethane (CH3CH2I)
and water. Here, hydroxyl group (OH) of ethanol has been replaced by an iodine atom (I).
CH3- CH2-OH + HI CH3- CH2-I + H2O
HH
H C C OH + HI
HH
Example: 2
HH
H C C I + H2O
HH
Ethyl chloride (CH3CH2Cl) reacts with potassium cyanide (KCN) to form ethyl cyanide
(CH3CH2CN) and potassium chloride. Here, chloride group (Cl) of ethyl chloride has
been replaced by cyanide group.
CH3-CH2-Cl +KCN CH3-CH2-CN+ KCl
HH
H C C Cl + KCN
HH
Example: 3
HH
H C C CN + KCl
HH
The gas ethane (CH3CH3 ) reacts with bromine vapour in presence of light to form
bromoethane (CH3CH2Br) and hydrogen bromide (HBr).
CH3-CH3 +Br2 CH3-CH2-Br + HBr
HH
H C C H
HH
+ Br2
HH
H C C Br + HBr
HH
ii. Addition reactions
Observe the above chemical reaction. In this reaction hydrogen reacts with ethene
molecule to give ethane. In this reaction, one hydrogen atom is added to each carbon
atom. Such type of chemical reaction is called addition reaction. Thus, those chemical
reactions in which atoms or groups of atoms are added to the organic molecule which has
one or more multiple covalent bonds are called addition reactions. In addition reactions,
the saturation of the organic molecules increases. It means that alkyne becomes alkene
and alkene becomes alkane. After addition reaction, molecular mass becomes equal to
the sum of molecular mass of the reacting molecules.
Memory Plus
The chemical reactions in which an unsaturated molecule reacts with another
molecule to form a saturated molecule is called addition reaction.
Fact with reason
The saturation of hydrocarbon increases after addition reaction. Why?
After addition reaction the saturation of the hydrocarbon molecules increases because
the number of multiple bonds between carbon atoms decreases.
C HEMI S TRY
Optional Science - 10
223
Example: 1
When ethene reacts with hydrogen bromide, it produces ethyl bromide. In this reaction,
hydrogen atom combines with one carbon atom and bromine atom combines with
another carbon atom. So, it is an addition reaction.
CH2 = CH2 + HBr
H H
C C +
H H
HBr
-
CH3 - CH2Br
HH
H C C Br
HH
Example: 2
Ethyne (C2H2) is an unsaturated hydrocarbon. It has a triple covalent bond between
carbon atoms. It combines with two molecules of hydrogen bromide to give 1, 1
dibromoethane (CH3CHBr2). As a result of this reaction, the two double bonds of ethyne
molecule break down and two atoms of bromine and two atoms of hydrogen combine.
Therefore, it is a kind of addition reaction.
CH≡CH +2HBr CH3-CHBr2
H Br
H C CH
H Br
H C C H +2HBr
Example: 3
When ethene reacts with hydrogen molecule, it produces ehane. It is also a kind of
combination reaction.
CH2 = CH2 + H2
H
H
/
C C +
H
H/
'
'
H2
-
CH3 - CH3
HH
H C CH
HH
iii. Elimination reactions
An elimination reaction is just opposite of addition reaction. In elimination reaction, a
saturated molecule is converted into an unsaturated molecule. During the reaction, a
saturated compound eliminates two atoms from the adjacent carbon atoms. As a result,
multiple covalent bonds are formed. Thus, those chemical reactions in which atoms or
group of atoms are eliminated from the organic molecule to give unsaturated product are
called elimination reactions.
Example: 1
Ethanol (CH3CH2OH), when mixed with concentrated sulphuric acid (H2SO4), it
produces ethene(CH2= CH2). In this reaction, one hydrogen atom (H) and one hydroxyl
group (OH)are eliminated at the same time. After the elimination of these atoms, the
saturated ethanol converted into unsaturated ethene. At the end of elimination reaction,
the molecular mass of product molecules is less than reactant molecules.
conc. H2SO4
CH3-CH2OH CH2 = CH2 + H2O
0
224
Optional Science - 10
C HEMI S TRY
H H
/
C C + H2O
/
H H
HH
conc. H2SO4
H C C OH
HH
'
'
Example: 2
When ethyl bromide is boiled with alcoholic solution of potassium hydroxide, it produces
alkene. In this reaction, one hydrogen and one bromine atoms are eliminated to give
ethene.
Alcoholic KOH
CH2 = CH2 + HBr
CH3-CH2Br H H
HH
Alcoholic KOH
/
C C + HBr
H C C Br
/
H H
HH
'
'
Example: 3
When bromoethene (CH2=CHBr) reacts with alcoholic potassium hydroxide, it loses one
hydrogen atom and one bromine atom. As a result, ethyne (C2H2 ) molecule is obtained.
In this reaction double bonded reactant molecule is converted into triple bonded product.
Alcoholic KOH
CH3= CHBr CH ≡ CH + HBr
H Br
Alcoholic KOH
/
CH ≡ CH + HBr
C C
/
H H
'
'
S.N. Addition reaction
S.N.
Substitution reaction
1.
Those chemical reactions in which 1.
atoms or groups of atoms are added
to the organic molecule which has
one or more multiple covalent
bonds are called addition reactions.
Those chemical reactions in which atoms
or groups of atoms are eliminated from
the organic molecules to give unsaturated
products are called elimination reactions.
2.
In this reaction, unsaturated reactant 2.
molecules become saturated.
In this reaction, saturated reactant
molecules become unsaturated.
Electrophiles and Nucleophiles
On the basis of excess and deficiency of electrons,
there are two types of chemical species. They are Nucleophile
Electrophile
called nucleophiles (electron rich) and electrophiles
(electron poor). During the chemical reaction, these
species move towards the specific direction. The movement of these species depends upon the
availability of electrons. We know that opposite charges attract each other and like charges repel
each other. Therefore, electrophile and nucleophile combine together whereas nucleophile
and nucleophile or electrophile and electrophile repel each other. During chemical reaction,
electrons flow from “electron rich” area to the “electron poor” area. In another word, electrons
always flow from the nucleophile to the electrophile. The flow of electrons is represented by
overhead arrow.
C HEMI S TRY
Optional Science - 10
0
225
Nucleophiles
Nucleophile is a Greek word. It has two parts. Nucleon means “nucleus” and philos means
“lover”. Therefore, Nucleophiles means “nucleus loving” species. Since, nucleus is
positively charged area, therefore nucleophiles are also known as “positive-charge loving”
species. Nucleophile has unshared pair electrons on it. It means it is electron rich species. The
direction of movement of nucleophiles is always towards the electron poor area. As a result,
nucleophile makes a covalent bond with electron poor species. Thus, nucleophile is an atom or
group of atoms which provides a pair of electrons to form a new covalent bond. Nucleophiles
are either negatively charged species or neutral molecules with one pair of available electrons.
They are generally denoted by the symbol “Nu”.
Memory Plus
Nucleophiles are rich of electrons, so they attack electrophiles.
The property of a nucleophile due to which it donates electrons is called nucleophilicity.
i. Negatively charged nucleophiles
These nucleophiles have a negative charge on them. For example:
Name of negative nucleophiles
Symbols
Hydroxide ion
OH-
Chloride ion
Cl-
Bromide ion
Br-
Iodide ion
I-
Cyanide ion
CN-
Oxide ion
O2-
Sulphide ion
S2-
Nitride ion
N3-
Alkoxide ion
RO-
ii. Neutral nucleophiles
These are neutral molecules with one pair electron for donation. For example:
Name of neutral nucleophiles
Symbols
H2O
Water
Ammonia
NH3
Alcohol
R-OH
Ether
R-O-R
Amines
R-NH2
0
226
Optional Science - 10
(
C HEMI S TRY
l
Electrophiles
Like nucleophiles, electrophile is a Greek word. It has two parts. Electron means “electron”
and philos means “lover”. So, electrophiles are“electron loving” species. As electrophiles are
electron poor species, they receive electrons from the electron rich species (nucleophiles). So,
the movement of electrophiles is always towards electron rich or negatively charged species.
Therefore, electrophiles are also known as “negative-charge loving” species. They have the
electron deficient centre. They accept electrons and form covalent bond. Thus, electrophiles are
atoms or groups of atoms which accept a pair of electrons to form a new covalent bond.
Electrophiles are reactive species and undergo reaction in suitable conditions. They can accept
an electron pair from the donor compound because they are either positively charged or
neutral molecules with electrons deficient centres. The chemical reaction which involves the
electrophiles is known as electrophilic reaction. Electrophiles are generally denoted by the
symbol “E”. There are two types of electrophiles. They are:
Memory Plus
Electrophiles are poor of electrons, so they attack nucleophiles
The property of an electrophile due to which it accepts electrons is called electrophilicity.
i.
Positively charged electrophiles: These electrophiles have a positive charge on them. For
example:
Name of positively charged electrophiles
Hydronium ion
H3O+
Hydrogen ion
H+
Ammonium ion
NH4+
Nitronium ion
NO2+
Carbonium ion or carbocation
ii.
Symbols
R3C+
Neutral electrophiles: These electrophiles have electron deficient centers. For example:
Name of neutral electrophiles
Symbols
Sulphur trioxide
SO3
Boron trifluoride
BF3
Boron trichloride
BCl3
Markonikov's rule
Markonikov’s rule is very important experiential rule. It is used to find out the final products
when hydrogen halides are added to alkenes. This rule states that "when an unsymmetrical
alkene reacts with hydrogen halide to give an alkyl halide, the hydrogen adds to the carbon of
the alkene that has the greater number of hydrogen atoms and the halogen to the carbon of the
alkene with the fewer number of hydrogen atoms". Alternatively, this rule can be stated that
the hydrogen atom is added to the carbon with the greatest number of hydrogen atoms while
halogen is added to the carbon with the least number of hydrogen atoms.
C HEMI S TRY
Optional Science - 10
0
227
Memory Plus
Markonikov's rule says that while adding hydrogen halide to the unsymmetrical alkene,
hydrogen always adds to the carbon which has more number of hydrogen atoms.
Example: 1
Reaction of propene with hydrogen bromide is explained with the help of Markonikov’s
rule. During this reaction, first of all, hydrogen bromide breaks down into hydrogen ion and
bromide ion. Hydrogen ion goes to the carbon atom where the numbers of hydrogen atoms are
two. At the same time bromide ion goes to the carbon atom where there is only one hydrogen
atom. Therefore, the product of this reaction is 2-bromo propane, but not 1-bromo propane.
i
H
H
H
C
I
H
C
I
H
C
-
H
I
+
HBr
H
Br
H
C
C
C
H
H
H
I
I
I
I
I
I
H
Markonikov's Product
H
ii
H
H
H
Br
C
I
I
C
C
H
I
I
H
H
I
I
H
Anti Markonikov's Product
Saytjeff’s rule
Saytzeff rule is pronounced as Zaitsev Rule. This rule looks like opposite of Markonikov’s
rule. This rule is used to predict the alkene products after elimination reaction. It can be used
in different elimination reactions. It states that, in an elimination reaction, the less hindrances
and more stable products are favoured over less stable and more hindrance products. Thus,
Saytzeff rule states that "the most substituted product is more stable and is favoured over
other products."
The stability of the compounds having multiple bonds is increased by electron withdrawing
groups. But the electron donating groups always decrease the stability. The examples of
electron donating groups are alkyl groups such as methyl, ethyl, propyl, etc. As these groups
are larger in size, they create more hindrance by making the alkene less stable. So, elimination
CH3
always occurs to give less bulky group towards the double bonds.
i
H
H
H
H
H
H
C
C
C
C
C
H
H
H
Br
H
H3C
CH2
CH
C
H
H
Satyzeff's Product
H
ii
H3C
CH2
CH2
_C/
CH
"
Anti Satyzeff's Product
228
Optional Science - 10
C HEMI S TRY
H
Memory Plus
When hydrogen is removed from alkane than a group is formed called alkyl group.
Example: 1
Reaction (i) CH3-CH2-CH2 –CH2-CHBr–CH3 CH3-CH2-CH=CH-CH3 (2-Penene) It is a major
product.
Reaction (ii) CH3-CH2-CH2 –CH2-CHBr–CH 3 CH3-CH2-CH2-CH=CH2 (1-Penene) It is a
minor product
In the given example, when hydrogen and bromine are removed from 2-bromopentane,
two products are possible. They are 2-Pentene and 1-Pentene. According to Saytzeff Rule,
2-Pentene (Satyzeff’s product) is more possible than 1-Pentene (anti Satyzeff’s product). This
is because 2-Pentene has less hindered as compared to 1-Pentene.
Answer writing skill
1.
Define organic chemistry.
Ans: The branch of chemistry in which we study about structure, properties, composition,
reactions and preparation of carbon containing compounds is called organic chemistry.
2.
What are organic compounds? Write down the necessary conditions to be the organic
compouns?
Ans:The chemical compounds which contain carbon as one of the primary elements are called
organic compounds. For examples: protein, fat, vitamins, carbohydrates, methane,
ethane, etc.
Two conditions which are necessary to be the organic compounds are:
3.
i.
Organic compounds must have carbon atom as one of the elements.
ii.
There must have covalent bond between the carbon atoms.
What is the main difference between addition and elimination reaction?
Ans: In addition reaction, atoms or groups of atoms are added to the molecule while in
elimination reaction, atoms or groups of atoms are eliminated from the molecule.
After addition reaction, the compound becomes more saturated while after elimination
reaction the compound becomes less saturated.
4.
What are nucleophiles and electrophiles? Write down any two examples of each.
Ans: Nucleophile are atoms or groups of atoms which provide a pair of electrons to form a
new covalent bond. For example: OH- , Cl- , CN- , H2O, NH3, etc.
Electrophiles are atoms or groups of atoms which accept a pair of electrons to form a
new covalent bond. For example: H3O+, NH4+, SO3, BF3, etc.
C HEMI S TRY
Optional Science - 10
0
229
5.
Write two differences between the Markonikov’s rule and the Satyzef’s Rule.
Ans: The differences between the Markonikov’s rule and the Satyzef’s Rule are given below.
S.N.
1.
Markonikov’s rule
S.N.
According to this rule "when an 1.
unsymmetrical alkene reacts with
hydrogen halide to give an alkyl halide,
the hydrogen adds to the carbon of the
alkene that has the greater number of
hydrogen atoms and the halogen to
the carbon of the alkene with a fewer
number of hydrogen atoms".
It is used to predict the product of the 2.
addition reaction.
2.
6.
Satyzef’s Rule
Saytzeff rule states that "the most
substituted product is more stable
and is favoured over other products."
It is used to predict the product and
stability of the elimination reactions.
Write down any three uses of organic compounds.
Ans: The uses of organic compounds are given below.
8.
i.
Industrial use of organic compound: Organic compounds are used for
manufacturing different kinds of organic materials like dynes, detergent, soap,
fuel, plastic, rubber, cosmetics, pharmaceutical goods, pesticides, fertilizers, etc.
ii.
Domestic use of organic compounds: Large numbers of organic compounds are
also used in our home. For example: sugar, oil, ghee, etc.
iii.
Medicinal use of organic compounds: Various organic compounds are used for
the treatment of diseases.
i
Complete the given chemical
reaction. Which product is more
H
stable and why? Give reason.
H
H
H
H
H
C
C
C
C
C
H
H
H
Br H
H
Ans: In the given example, when
hydrogen and bromine are
removed from 2-bromopentane,
ii
two products are possible. They
are 2-Pentene and 1-Pentene. According to Saytzeff Rule, 2-Pentene (Satyzeff’s product)
is more possible than 1-Pentene (anti Satyzeff’s product).This is because 2-Pentene is less
sterically hindered as compared to 1-Pentene. As we know that according to Satyzeff’s
rule the product with less sterically hindered is major and more stable.
CH3
i
H
H
H
H
H
H
C
C
C
C
C
H
H
H
Br H
H3C
CH2
CH
C
H
H
Satyzeff's Product
ii
H3C
CH2
CH2
CH
_/
C
~
Anti Satyzeff's Product
230
Optional Science - 10
C HEMI S TRY
H
H
Exercise
----~ ----Step
1
1.
Define the following
2.
a. Organic chemistry
b. Organic compounds
c.
Nucleophiles
d. Electrophyles
e. Addition reaction
f. Substitution reaction.
g. Elimination reaction.
What are negative nucleophiles? Write any two examples.
3.
What are neutral eletrophiles? Write any two examples.
4.
What is Markonikov’s rule?
5.
State Satyzef’s rule.
Step
1.
2.
2
Differentiate between:
a. Organic compounds and inorganic compounds.
b. Nucleophiles and electrophiles.
c.
Addition reaction and elimination reaction.
d. Markonikov’s rule and Satyzef’s rule.
Give reason.
a. Carbides, carbonates, cyanides, etc. are called inorganic compounds.
b. Wohler synthesis is considered as a milestone in the history of organic chemistry.
c.
The saturation of hydrocarbon increases after addition reaction.
d. BF3 is an electrophile. Why?
3.
Give an example of the chemical reaction to explain Markonikov’s rule.
4.
Give an example of the chemical reaction to explain Satyzef’s rule.
C HEMI S TRY
Optional Science - 10
231
Step
3
1.
What are the uses of organic compounds in our daily life?
2.
Explain the importance of markonikov’s rule.
3.
Describe the importance of Satyzef’s rule.
4.
According to which rules do the given reactions belong to? State the rules.
(i) CH3-CH2-CH2 –CH2-CHBr–CH 3 CH3-CH2-CH=CH-CH3
(ii) CH3-CH=CH2 +HBr CH3-CHBr-CH3
5.
Identify the types of reactions with reason.
i) CH2 = CH2 + H2
Step
CH3 - CH3
ii) CH3-CH2-Br + H2O CH3-CH2-OH + HBr
4
1.
What is carbocation? In which reaction does it form? Explain this reaction with one example.
2.
What types of reaction are called substitution reactions? Describe with the help of reactions.
3.
Explain Markovnikov's and Saytjeff’s rules with the help of chemical reactions.
Multiple choice questions (MCQ):
1.
A nucleophile is a reactant that………a pair of electrons to form a new covalent bond.
a.
Shares
b. Donates
2.
c. Bonds
Which is an electrophile?
d. Accepts
3.
a. H2O
c. R3C+
Which is a neutral nucleophile?
b. Cl
d. None of the above
4.
a. BF3
c. OHIdentify neutral eletrophile?
b. SCNd. H2O
a.
c.
b. NO2+
d. All above
NH4+
BCl3
5.
Addition reaction
6.
a. Increases saturation of the products
b. Decreases saturation of the products
c. Saturation does not change
d. None of the them
Addition of …………to alkene explains Markonikov’s rule.
0
a.
NH3
b. NaCl
c.
HBr
d. CH4
232
Optional Science - 10
C HEMI S TRY
UNIT
12
METALS AND
METALLURGY
Georgius Agricola born on 1495 AD and died on 1555 AD. His real name is George Bauer.
Georgius Agricola is his Latin version name. He was the pioneer chemist who studied
about the Earth, rocks, minerals and fossils. He was the first person who studied about
metallurgy and mineralogy. He also studied structural geology and paleontology. He
wrote the first book on physical geology named De Ortu et Causis Subterraneorum in 1946.
Syllabus issued by CDC
•
•
•
•
Learning objectives:
Introduction to aluminium, silver
and gold
General metallurgy of aluminium,
silver and gold
Physical properties, chemical
properties and uses of aluminium,
silver and gold
Alloy and amalgum
After completing the study of this unit, students
will be able to:
• Describe the metallurgical process of
aluminium, silver and gold.
• Explain the physical and chemical properties
of aluminium, silver and gold.
• Explain the uses of aluminium, silver and gold.
• Describe the alloys and amalgam.
Key terms and terminologies of the unit
1.
Ore: ore is a mineral which contains large amount of the particular metal.
2.
Metallurgy: metallurgy is a process of different steps by which pure metal can be
extracted from the particular ore.
3.
Aquaregia: Aquaregia is a homogenous mixture of three part of concentrated
hydrochloric acid and one part of concentrated nitric acid.
4.
Alloy: Alloy is a homogeneous mixture of two or more metals or sometimes metals
and non-metals.
5.
Amalgam: Amalgam is an alloy of mercury with other metals like sodium, potassium,
silver, tin, copper, zinc, etc.
C HEMI S TRY
Optional Science - 10
0
233
Introduction
Metals are present on the earth's crust. Some metals are also found in the form of compounds
in seawater. Examples: sodium chloride, potassium chloride, magnesium chloride, etc. The
elements or compounds which occur naturally in the earth's crust are known as minerals.
Some minerals contain high percentage of particular metal are called ores. Thus, ore is a
mineral which contains large amount of the particular metal. From the respective ores metals
can be extracted by applying several steps. Collectively these steps are called metallurgical
steps. Thus, metallurgy is a process of different steps by which pure metal can be extracted
from the particular ore. After getting the pure metal, it is used for different purposes. In this
unit, we will discuss about the metallurgy of aluminium, silver and gold along with their
physical and chemical properties.
Aluminium
Introduction
Name
Aluminium
Symbol
Al
Atomic weight
27
Atomic number
13
Electronic configuration
1s2 ,2s22p6,3s23p1
Position in periodic table
Period-3 and group-IIIA (13)
Valency
3
Occurrence
Aluminum is the most abundant metal on the earth's crust. It occurs about 68.1% in natu re.
It is a most reactive metal. So, it does not occur in Free State in the nature. In combined state,
aluminium is found in different types of compounds like sulphides, oxides, fluorides, etc. The
main ores of aluminium are bauxite, cryolite, felspar, etc. Aluminium is a light metal, so it is
used to make different kinds of household utensils, parts of aircraft, etc.
Ores of aluminium
Name of ores
Molecular formula
Bauxite
Al2O3.2H2O
Felspar
K(AlSiO3.O8)
Cryolite
Na3AlF6
Extraction of aluminium
Aluminium is one of the abundant elements on the earth. It is mainly found in the bauxite
ore. This ore contains different kinds of impurities like silica (SiO2), ferric oxide, etc. So, we
can extract aluminium mainly from the bauxite ore. The extraction of aluminium involves
following steps.
i.
Collection of ore: The chief ore of aluminium is bauxite. It is found in the different places
on the earth. So, bauxite ore is collected from the respective places using different kinds
of tools and techniques. After collection, the ore is transported to the site of extraction.
0
234
Optional Science - 10
C HEMI S TRY
ii.
Grinding of ore: While mining, the bauxite ore is present in the form of big lumps. These
big lumps of ore are crushed into smaller pieces with the help of crusher machine. After
crushing the pieces of bauxite ore are ground in the stamp mill or pulverizing machine to
make fine powder.
iii. Heating of ore with sodium hydroxide: After grinding, we get powder ore. This powder
ore is mixed with sodium hydroxide to make solution. Now, the solution is heated to
form a complex compound called sodium metal aluminate (NaAlO2).This sodium metal
aluminate is separated and treated with water and dilute hydrochloric acid. As a result,
we get precipitate of aluminium hydroxide [Al(OH)3].This aluminium hydroxide is
dehydrated to remove moisture. The anhydrous aluminium hydroxide is heated strongly
to get aluminium oxide. This aluminium oxide is commonly called alumina (Al2O3).
iv. Purification of aluminium: After getting alumina, we apply refining process. It is the last
step of the metallurgical process. In this step, the molten alumina is purified by using
electrolysis process. In electrolysis process, the impure alumina is kept at anode and pure
alumina is kept at cathode. As a result, about 99% pure aluminium is obtained.
Properties of aluminium
A) Physical properties
i.
Aluminium is a white coloured metal with bluish shine.
ii. Its melting point is 6600C and boiling point is 18000C.
iii. It is a light metal having specific gravity 2.7.
iv. It is malleable, ductile and good conductor of heat and electricity.
B) Chemical Properties
i.
Reaction of aluminium with air: Aluminium does not react with dry air but in
presence of moisture, it reacts with oxygen to form aluminium oxide (Al2O3).
4Al + 3O2
∆
2Al2O3
ii. Reaction with water: Aluminium is passive with cold water but it reacts with steam
to produce aluminium hydroxide {Al(OH)3} and hydrogen gas (H2).
2Al + 6H2O → 2Al(OH)3 + 3H2↑
iii. Reaction with Acids
a. Reaction with hydrochloric acid: Aluminium reacts with dilute and concentrated
hydrochloric acid to give aluminium chloride (AlCl3) and hydrogen gas (H2).
2Al + 6HCl → 2AlCl3 + 3H2↑
b. Reaction with sulphuric acid
i.
Reaction of aluminium with dilute sulphuric acid
Aluminium reacts with dilute sulphuric acid to give aluminium sulphate{(Al2(SO4)3}
and hydrogen gas (H2).
2Al + 2H2SO4 → Al2(SO4)3 + 3H2↑
C HEMI S TRY
Optional Science - 10
0
235
ii. Reaction of aluminium with concentrated sulphuric acid
Aluminium reacts with concentrated sulphuric acid to give aluminium sulphate
Al2(SO4)3, sulphur dioxide(SO2) and water(H2O).
2Al + 6H2SO4 → Al2(SO4)3 + 3SO2+ 6H2O
c. Reaction with nitric acid
Aluminium does not react with dilute as well as concentrated nitric acid. It is because
aluminium makes a protective oxide layer over its surface.
Fact with reason
Aluminium does not react with dilute as well as concentrated nitric acid. Why?
Aluminium does not react with dilute as well as concentrated nitric acid because in
presence of oxygen, aluminium makes a thin protective oxide layer over its surface.
This oxide layer prevents the reaction of aluminium with nitric acid.
3. Reaction with halogens
Aluminium reacts with halogens to form respective halides.
2Al + 3Cl2 → 2AlCl3 (Aluminium chloride)
2Al + 3Br2 → 2AlBr3 (Aluminium bromide)
2Al + 3I2 → 2AlI3 (Aluminium iodide)
Memory Plus
The elements which are kept in VIIA group of the modern periodic table are called
halogens. Examples: F2, Cl2, Br2, I2, etc. They are called halogens because they are
present in the sea water in the form of salt.
4.
Reaction with nitrogen
Aluminium reacts with nitrogen to form aluminium nitride.
2Al + N2 → 2AlN (Aluminium nitride)
Memory Plus
Aluminium nitride (AlN) can be used as a chemical fertilizer.
5. Reaction with alkalis
Aluminium reacts with sodium hydroxide to give sodium metal aluminate. This reaction
takes place in presence of water.
2Al + 2NaOH + 2H2O → 2NaAlO2 + 2H2↑
Fact with reason
Aluminium is used for making aluminium foils for wrapping foods, pharmaceutical
products, biscuits, chocolates, cigarettes, etc. Why?
Aluminium is used for making aluminium foils for wrapping foods, pharmaceutical
products, biscuits, chocolates, cigarettes, etc. because it is highly malleable and light
metal. It does not get rust.
236
Optional Science - 10
C HEMI S TRY
Uses of aluminium
1.
As aluminium is good conductor of electricity, it is used to make electric transmission wires.
2.
It is used to make different types of household utensils, pictures, frames, etc.
3.
It is used for making aluminium foils for wrapping foods, pharmaceutical products,
biscuits, chocolates, cigarettes, etc.
4.
It is used to make different parts of aircrafts, ships, bushes, cars, etc. as it is a light metal.
5.
It is used to make alloys and coins.
6.
It is used to make reducing agent in different metallurgical process.
Fact with reason
Aluminium is used to make parts of aircrafts, ships, bushes, cars, etc. Why?
Aluminium is used to make parts of aircrafts, ships, bushes, cars, etc. because
i. Aluminium is a light metal.
ii. It is highly malleable metal.
iii. It does not get rust continuously.
Silver
Introduction
[Name
Silver
Latin name
Argentum
I
I
Symbol
I
Atomic weight
~
I
I
-
Ag
107.9
Atomic number
I
47
Electronic configuration
I
[Kr]4d10 5s1
Position in periodic table
Period-5 and group-IB (11)
Valency
1
Occurrence
-
-
-
Silver is an example of d-block element. It is white coloured shiny metal. It is comparatively
less reactive metal than iron, copper and aluminium. So, it occurs in Free State in the earth.
Compare to gold, silver is more reactive metal. So, it also occurs in in the different compounds.
The compounds of silver which are present in the earth's crust are called ores of silver.
Examples: argentite, horn solver, ruby silver, etc.
Memory Plus
The symbol of silver "Ag" is derived from the Latin word "argentum" meaning white.
Thus, silver is white coloured shiny metal.
C HEMI S TRY
Optional Science - 10
237
Ores of Silver
S.N.
Ores of silver
Molecular formula
1.
Argentite (silver glance)
Ag2S
2.
Horn silver
3.
Ruby silver
4.
Silver copper glance
AgCl
3Ag2S.Sb2S3
(Ag.Cu)2S
Extraction of Silver
The main ore of silver is argentite. So, silver is mainly extracted from the argentite ore by using
cyanide process. The cyanide process involves following steps.
1.
Mining: Argentite ore is found in the different parts of the earth. From these respective
places, argentite ore is taken out using different methods. The ore thus obtained contains
large amount of impurities. Now, the ore is concentrated to remove these unwanted
impurities.
2.
Crushing and pulverization: The ore is crushed in jaw crushers and then powdered to
make fine particles in ball mills.
3.
Concentration of the argentite ore: Since argentite is a sulphide ore, we use froth
floatation process to remove its impurities. During cyanide process, we make a mixture
of argentite ore, water and pine oil. This
Froth bubbles
carrying sulphide
mixture is kept in a container. In the container
Compressed
ore particles
_,.... air
we pass strong current of air. The sulphide
ore now becomes wet in pine oil. The density
I
of wetted sulphide ore is less than water. So, it
Sulphide ore
floats on the container in the form of froth.
particles
The impurities present in the ore have more
Water
containing
density than water. So, they settle down at the
pine oil
bottom of the container. Now, the froth
i:::;.::::.::;.:.:::::.:.=.::.:s.::!.::!:~:=.:Jc!::r- - Gangue
Froth floatation process for the concentration of sulphide ores.
containing argentite ore is separated like
cream from the milk.
Memory Plus
The impurities present in sulphide ore are separated by using froth floatation process.
4.
Treatment with sodium cyanide: The concentrated ore is treated with dilute aqueous
solution of sodium cyanide (about 0.4 to 0.7%) and agitated with a strong blow of air.
Now, sodium cyanide reacts with argentite ore to give a complex compound called
sodium argentocyanide Na [Ag(CN)2] and sodium sulphide (Na2S).The sodium sulphide
then converted into sodium sulphate due to the reaction with oxygen. Sodium sulphate
is removed to proceed the reaction.
Ag2S + 4NaCN → 2Na[Ag(CN)2] + Na2S
Na2S + 2O2 → Na2SO4
238
Optional Science - 10
C HEMI S TRY
5.
Silver precipitation: The solution containing sodium argentocyanide is filtered to remove
insoluble impurities. The clear solution of sodium argentocyanide is then treated with
zinc. As zinc is more electropositive than silver, it displaces silver from the solution. Now,
silver gets precipitated on the bottom of the container. Silver obtained in this process is
called spongy silver. Finally, the separated silver is fused with borax or potassium nitrate
to get compact silver.
Zn + 2Na[Ag(CN)2] → Na2[Zn(CN)4] + 2Ag
6.
Silver Refining: Silver obtained in this process contains some impurities like zinc,
copper, gold, etc. So, purification of silver is done by using electro-refining process.
During electro-refining process, impure silver is connected at cathode and pure silver is
connected at anode. In this process, silver nitrate solution is used as an electrolyte.
Properties of Silver
A) Physical Properties
1. Silver is a white lustrous metal.
2. It is highly malleable, ductile and good conductor of heat and electricity.
3. Its melting point is 9560C and boiling point is 19550C.
4. Its specific gravity is 10.52
B) Chemical Properties
1. Reaction of silver with halogens (Cl2, Br2, I2)
Silver reacts with halogens to give corresponding halides.
2Ag + Cl2 → 2AgCl
(Silver chloride)
2Ag + Br2 → 2AgBr
(Silver bromide)
2Ag + I2 → 2AgI
(Silver iodide)
2. Reaction of silver with sulphur
Silver reacts with sulphur to give silver sulphide.
∆
2Ag + S
Ag2S
3. Reaction of silver with acids
a.
Reaction of silver with hydrochloric acid:
Silver does not react with dilute hydrochloric acid but in presence of oxygen it
reacts with concentrated hydrochloric acid to give silver chloride and water.
4Ag + 4HCl + O2 → 4AgCl + 2H2O
b.
Reaction of silver with sulphuric acid
Silver does not react with dilute sulphuric acid but it reacts with concentrated
H2SO4 to give silver sulphate, sulphur dioxide and water.
2Ag + 2H2SO4 → Ag2SO4 + SO2 + 2H2O
Memory Plus
Silver does not react with dilute hydrochloric acid and dilute sulphuric acid.
C HEMI S TRY
Optional Science - 10
0
239
c.
Reaction of silver with nitric acid
i. Reaction of silver with dilute nitric acid
Silver reacts with dilute nitric acid to give silver nitrate, nitric oxide and water.
3Ag + 4HNO3 → 3AgNO3 + NO + 2H2O
ii. Reaction of silver with concentrated nitric acid
Silver reacts with concentrated nitric acid to give silver nitrate, nitrogen dioxide
and water.
Ag + 2HNO3 → AgNO3 + NO2 + H2O
Memory Plus
Silver nitrate (AgNO3) is sensitive to light and organic compounds. So, it reacts easily
with our skin to make black stain. So, this property is applied during election for staining
fingers of voters who have cast their votes.
Uses of silver
1.
Silver is used to make different types of ornaments, utensils, coins, medals, etc.
2.
Silver bromide (AgBr) is used in photography.
3.
It is used in silver plating.
4.
It is used for making silvering mirror.
5.
It is used for filling the teeth.
6.
It is also used to make medicines.
Memory Plus
Dental alloy is made from silver and tin. It is used for filling teeth cavity.
Gold
Introduction
Name
Gold
Latin name
Aurum
Symbol
Au
Atomic weight
197
Atomic number
79
Electronic configuration
[Xe] 4f14 5d10 6s1
Position in periodic table
Period-6 and group-IB (11)
Valency
1 and 3
Occurrence
Gold is a passive metal. In general condition, it does not react with most of the substances like
air, water, acid, base, etc. So, it is also called a noble metal and occurs in Free State. In native
state gold is found in alluvial soil. In general conditions, it is found in reef gold mixed with
240
Optional Science - 10
C HEMI S TRY
quartz or alluvial soil. In Nepal, alluvial gold is found in Karnali and Sunkoshi Rivers. But, the
commercial extraction of gold from these places has been found uneconomical.
Fact with reason
Gold occurs freely in nature. Why?
Gold occurs freely in nature because in general conditions, it does not react with most of
the substances like air, water, individual acid, base, etc.
Ores of Gold
S.N. Name of Ores
Molecular formula
1
Alluvial soil or quartz veins
It is a mixture
2
Calverite
2
Petzite
AuTe2
(Ag.Au)2
Fact with reason
Gold is also called a noble metal. Why?
Gold is also called a noble metal because in general conditions, it does not react with
most of the substances like air, water, individual acid, base, etc.
Extraction of Gold
Gold is mainly extracted by using two methods. They are:
1.
Sluicing Method
1.
Sluicing
2. Cyanide Method
Sluicing is a physical method of extraction of gold. In this method we use a pan or long
channel called sluice. During this process, the alluvial soil is washed using high pressure
water. The mixture of alluvial soil and water runs downward through the sluice. While
running the mixture, water and impurities continuously flow down along the sluice while
the heavier gold particles settle down in the cavities of sluice. Finally, gold particles are
taken out from the sluice cavities and refined for the further use.
2.
Cyanide process
Cyanide process is a chemical method of extraction of gold. In this process, we use
solution of sodium cyanide (NaCN) for the extraction of gold. During this process, we
make a mixture of impure gold and sodium cyanide. A strong jet of air is blown to this
mixture. While passing air jet, the gold gets dissolved in the sodium cyanide solution
to form sodium aurocyanide and sodium hydroxide. Now, gold is extracted by adding
zinc dust in the solution of sodium aurocyanide. As zinc is more reactive than gold, it
displaces gold from the aurocyanide in the form of precipitate. The necessary reactions
for this process are given below.
4Au + 8NaCN + 2H2O → 4 Na[Au(CN)2] + 4NaOH
Zn + 2Na[Au(CN)2] → Na2[Zn(CN)4] + 2Au
C HEMI S TRY
Optional Science - 10
241
Gold obtained from the above process is not completely pure. It contains impurities
of zinc and lead. So, it is purified by using several refining processes to get pure gold.
Among the several refining methods, electro-refining is the best one. In this method, we
take impure gold at anode and pure gold at cathode. For this process, acidified gold
chloride solution is used as an electrolyte.
Properties of Gold
A. Physical properties of gold
1. Gold is a soft heavy metal with shining yellow lutstre.
2. It is good conductor of heat and electricity.
3. It is highly malleable and ductile in natrue.
4. Its melting point is 10630C and boiling point is 25300C.
5. Its specific gravity is 19.3.
Memory Plus
The relative density or specific gravity of gold is 19.3. It means gold is 19.3 times heavier
than pure water at 40C.
B. Chemical properties of gold
i. Reaction of gold with halogens
Gold reacts with halogens to give gold halides.
2Au + 3Cl2 → 2AuCl3 (Gold chloride)
ii. Reaction of gold with aquaregia
As we have already discussed that gold is very less reactive metal. In ordinary
condition, It does not react with acids. But, it reacts with aquaregia. Aquaregia is a
homogenous mixture of three part of concentrated hydrochloric acid and one part of
concentrated nitric acid. Gold reacts with aquaregia to give auric chloride, nitrosyl
chloride and water.
{3HCl + HNO3 → NOCl + 2H2O + 2Cl } x 3
9HCl + 3HNO3 → 3NOCl + 6H2O + 6Cl
2Au + 6Cl → 2AuCl3
2Au + 9HCl + 3HNO3 → 2AuCl3 + 3NOCl + 6H2O
Memory Plus
Aquaregia produces nascent chlorine (Cl) that reacts with gold to give gold chloride.
0
242
Optional Science - 10
C HEMI S TRY
Uses of Gold
1.
Gold is widely used for making ornaments and jewelleries.
2.
It is used to coat precious metals, idols, statues, roof tops, temples, etc.
3.
It is used for making gold coins.
4.
It is used in photography.
5.
It is used for making medicines
6.
It is used for filling teeth cavities.
7.
It is used in gold-leaf electroscope.
8.
It is used for making important gold compounds like gold chloride.
Alloy
When two or more non-reacting substances are mixed together, we get a resultant mass called
mixture. In mixture, the mixing substances do not lose their identity. While making mixture,
when two or more metals are mixed together, then the resultant substance is called an alloy.
Thus, alloy is a homogeneous mixture of two or more metals or sometimes metals and nonmetals. If an alloy is made from two components, it is called binary alloy. If an alloy is made
from three components, it is called a ternary alloy. Similarly, if an alloy is made from four
components, it is called a quaternary alloy.
While making alloys we always desire certain common properties that are different from
their components. For example, steel is an alloy of iron and carbon. In steel, iron is a main
component but it is stronger than iron.
As an alloy is a mixture of metals, it does not have fixed melting point. Its melting point
depends upon the mixing components and their percentage. Therefore, alloys have a melting
range. For specific purposes, we design some alloys that have single melting point. Such alloys
are called eutectic alloys.
Properties of alloys
Alloys have the following properties.
1.
Generally alloys are harder than their components.
2.
Generally, alloys are brittle than their components.
3.
They are good conductors of heat and electricity.
4.
Strength of alloys is more than their components.
5.
They are malleable and ductile.
6.
They have low melting point.
Memory Plus
Sometimes an alloy is just named according to the base metal. For example, 14 karat
(58%) gold is an alloy of gold with other elements.
C HEMI S TRY
Optional Science - 10
243
Some examples of alloys
S.N Name of alloy
Composition
1.
Steel
Iron (80–98%), carbon (0.2–2%), other metals such as chromium,
manganese, and vanadium
2.
Stainless steel
Iron (more than 50%), chromium (10–30%), small amount of
carbon, nickel, manganese, molybdenum and other metals.
3.
Brass
Copper (65–90%) and zinc (10–35%)
4.
Amalgam
Mercury (45–55%), silver, tin, copper and zinc
5.
Bronze
Copper (78–95%), tin
aluminum, or silicon
6.
Bell Metal
Copper (78%) and tin (22%),
7.
White gold
(18 carat gold)
Gold (75%), palladium (17%), silver (4%) and copper (4%)
8.
Nichrome
Nickel (80%) and chromium (20%)
(5–22%),
manganese,
phosphorus,
Amalgam
Amalgam is an alloy of mercury with other metals like sodium, potassium, silver, tin, copper,
zinc, etc. Almost all metals can form amalgams with mercury. In amalgam, mercury is present
about 45–55%. The metals which form amalgam with mercury are silver, tin, copper, zinc,
etc. There are many amalgams for example, zinc amalgam, potassium amalgam, sodium
amalgam, aluminium amalgam, tin amalgam, silver amalgam, etc. Among them, the silvermercury amalgam is used in dentistry to fill teeth and gold-mercury amalgam is used in the
extraction process of gold.
Memory Plus
The silver-mercury amalgam is used in dentistry to fill teeth cavity.
Answer writing skill
1.
What is metallurgy? Why is it important?
Ans: Metallurgy is a process of different steps by which pure metal can be extracted from the
particular ore. As ore contains different kinds of impurities, metallurgical process is very
important to take out the pure metal from the respective ores.
2.
Write down two important ores of each aluminium, silver and gold.
Ans:
244
Metal
Two ores
Aluminium
Bauxite and Cryolite
Silver
Argentite and Horn silver
Gold
Alluvial soil and Calverite
Optional Science - 10
C HEMI S TRY
3.
Aluminium is used for making aluminium foils for wrapping foods, pharmaceutical
products, biscuits, chocolates, cigarettes, etc. Why?
Ans: Aluminium is used for making aluminium foils for wrapping foods, pharmaceutical
products, biscuits, chocolates, cigarettes, etc. because
i. Aluminium is highly malleable and light metal.
4.
ii. It does not get rust continuously.
Write down the reaction of silver with sulphuric acid.
Ans: Silver does not react with dilute sulphuric acid but it reacts with concentrated H2SO4 to
give silver sulphate, sulphur dioxide and water.
2Ag + 2H2SO4 → Ag2SO4 + SO2 + 2H2O
5.
What is aquaregia? Write down the balance chemical reaction of aquaregia with gold.
Ans: Aquaregia is a homogenous mixture of three parts of concentrated hydrochloric acid and
one part of concentrated nitric acid. Gold reacts with aquaregia to give auric chloride,
nitrosyl chloride and water.
2Au + 9HCl + 3HNO3 → 2AuCl3 + 3NOCl + 6H2O
6.
Write down any three properties of alloy.
Ans: The properties of alloys are:
1. Generally alloys are harder than their components.
2. Generally, alloys are brittle than their components.
7.
3. They are good conductors of heat and electricity.
Write down the composition of stainless steel, brass and bronze.
i.
Composition of stainless steel is Iron (more than 50%), chromium (10–30%), small
amount of carbon, nickel, manganese, molybdenum and other metals.
ii. Composition of brass is copper (65–90%) and zinc (10–35%)
8.
iii. Composition of bronze is copper (78–95%), tin (5–22%), manganese, phosphorus,
aluminum, or silicon
Write down any three uses of Gold.
i.
Gold is widely used for making ornaments, jewelleries, idols, statues, roof tops,
temples, etc.
ii. It is used for making gold coins, photography and gold-leaf electroscope.
iii. It is used for making medicines and filling the teeth cavities.
C HEMI S TRY
Optional Science - 10
245
Exercise
Step
1
1.
What is metallurgy?
2.
Define ore.
3.
Show the sub-shell electronic configuration of aluminium
4.
What is aquaregia?
5.
Where do we use sluice method?
6.
Mention the period and group of aluminium, silver and gold.
7.
Which element is present in aquaregia to react with gold?
8.
Write down any two ores of each aluminium, silver and gold.
9.
Define alloy and amalgam.
10.
Write down any two alloys with their composition.
11.
Which metal can be extracted from bauxite, argentite and alluvial soil.
12.
What is amalgam? Which amalgam is used to fill the cavity of teeth?
Step
1.
2
Give reason.
a.
Aluminium does not react with dilute as well as concentrated nitric acid.
b. Aluminium is used for making aluminium foils for wrapping foods, pharmaceutical
products, biscuits, chocolates, cigarettes, etc.
c.
Aluminium is used to make parts of aircrafts, ships, bushes, cars, etc.
d. Gold occurs freely in nature.
2.
e. Gold is also called a noble metal.
Write down the occurrence of the following metals.
3.
(a) Aluminium
(b) Silver
(c) Gold
Write down the electronic configuration, period and group of the following metals.
(a) Aluminium
246
(b) Silver
Optional Science - 10
C HEMI S TRY
(c) Gold
Step
3
1.
Write down any three physical properties of the following metals.
2.
(a) Aluminium
(b) Silver
Write down any three uses of the following metals.
3.
(a) Aluminium
(b) Silver
(c) Gold
Write down the balanced chemical reaction of the aluminium with
4.
(a) Hydrochloric acid
(b) Sulphuric acid
Write down the balanced chemical reaction of the silver with
5.
(a) Hydrochloric acid
(b) Sulphuric acid
(c) Nitric acid
Write down the balanced chemical reaction of gold with aquaregia.
Step
(c) Gold
4
1.
Describe the metallurgical steps of aluminium.
2.
What is chief ore of silver? Describe the extraction of silver from its chief ore.
3.
Describe sluice method of extraction of gold.
4.
Describe cyanide method to extract gold.
5.
What is alloy? Why do we make alloy? Write down three properties of alloy.
Multiple choice questions (MCQ)
1.
The symbol of gold is
2.
i. Ag
ii. Au
iii. G
iv. Al
What is added during the extraction of silver?
3.
i. Potassium permanganate
iii. Sodium cyanide
Gold reacts with
ii Sodium argento cyanide
iv. Potassium phosphate
4.
i. Aquaregia
iii. Hydrochloric acid
Aluminium does not react with
ii Sulphuric acid
iv. Nitric acid
5.
i. Oxygen
iii. Hydrochloric acid
The main ore of silver is
ii Sulphuric acid
iv. Nitric acid
6.
i. Alluvial soil
ii. Argentite
iii. Haematite
iv. Bauxige
Which one is used to extract aluminium
i. Alluvial soil
iii. Haematite
ii. Argentite
iv. Bauxige
C HEMI S TRY
Optional Science - 10
0
247
UNIT
13
BIOMOLECULES
Carl Alexander Neuberg (1877–1956) was born in Germany and died in New York. He
was an early pioneer in biochemistry, and he is often referred to as the "Father of Modern
Biochemistry". One of his important contributions in science is the discovery of carboxylase
and the elucidation of alcoholic fermentation.
Syllabus issued by CDC
Learning objectives:
At the end of this unit, the students will be able to:
• describe the importance of some biomolecules
like carbohydrates, proteins, lipids, enzymes
and nucleic acids
Atomic mass, molecular mass and
• describe sources and uses in the human body
mole concept
of carbohydrates, proteins, lipids, enzymes
Quantum numbers
and nucleic acids.
Concentration (Normality, molarity,
gram per litre and percentage)
Theory
Practical
3
1
Key terms and terminologies of the unit
1.
Micromolecule: A molecule containing a low number of atoms.
2.
Macromolecule: A molecule containing a very large number of atoms, such as a
protein, nucleic acid or synthetic polymer.
3.
Biomolecules: Biomolecules are defined as organic molecules present in living things
that are involved in the growth, repair and metabolic process of a living organism
4.
Carbohydrates: Carbohydrate is a biomolecule consisting of carbon (C), hydrogen
(H) and oxygen (O) atoms which is used as energy source (calories) by the body of
living organisms.
5.
Monosaccharide: A monosaccharide is the most basic form of carbohydrates with a
single sugar molecule.
248
Optional Science - 10
BIOLOGY
6.
Disaccharide: A carbohydrate consisting of two sugar molecules is called a
disaccharide.
7.
Oligosaccharide: Oligosaccharide is a type of sugar containing a chain of 2-10
monosaccharides.
8.
Polysaccharide: A polysaccharide is a polymer formed by many monosaccharides
joined together by a glycosidic bond.
9.
Lipid: Lipids are the naturally occuring organic compounds commonly known as
fats or oils and their derivatives.
10.
Proteins: Proteins are large, complex nitrogen-containing organic compounds
composed of one or more long chains of amino acids.
11.
Amino acids: Amino acids are organic biomolecules that are attached to each other
to form long chains of proteins.
12.
Essential amino acids: Amino acids that cannot be synthesized in the body and
should be supplied through diet are called essential amino acids.
13.
Non-essential amino acids: Amino acids that are synthesized in the human body
either from essential amino acids or from normal protein breakdowns are called nonessential amino acids.
14.
Semi-essential amino acids: Amino acids which can partly synthesized in adult
human body but are necessary to supply through diet in infants are called semiessential amino acids.
15.
First class protein: Proteins that contain all the essential amino acids are called first
class proteins.
16.
Second class protein: Proteins that are deficient in one or more essential amino acids
are called second class proteins.
17.
Enzyme: Enzymes are large biomolecules that act as catalysts for biochemical
reactions within living cells in every plant and animal.
18.
Nucleic acids: Nucleic acids are large organic compounds found in the chromosomes
of living cells and viruses.
19.
Minerals: Minerals are essential inorganic nutrients for organisms to perform
functions necessary for life.
20.
Deoxyribonucleic Acid (DNA): DNA is a double helical macromolecule. It contains
genetic information.
Introduction
All living matter is largely made of up biomolecules. They are the essential chemical
components of living organisms. The chemical components of a cell can be inorganic (salts,
minerals and water) and organic (carbohydrates, proteins, lipids, nucleic acids and vitamins).
Biomolecules are defined as organic molecules present in living things that are involved in the
growth, repair and metabolic process of a living organism.
BIOLOGY
Optional Science - 10
249
Carbohydrates
Carbohydrates are the most abundant biomolecules found in living organism on earth. The
carbohydrates are the major source of energy, both for plants and animals. It contains carbon,
hydrogen and oxygen as its main elements. Carbohydrate is a biomolecule consisting of
carbon (C), hydrogen (H) and oxygen (O) atoms which is used as energy source (calories) by
the body of living organisms. Carbohydrates are often referred to as sugars or saccharides.
Memory Plus
The word saccharide refers to sugar, or sweet substance, and is derived from the Greek
word sakcharon.
Classification of Carbohydrates
Carbohydrates
Monosaccharides
(1 sugar molecule)
Oligosaccharides
(2-10 sugar molecule)
Polysaccharides
(10+ sugar molecule)
glucose, fructose,
galactose
sucrose, lactose,
maltose, raffinose
starch, glycogen,
cellulose, fibers
On the basis of the number of sugar units, carbohydrates can be classified into three major
classes as monosaccharides, oligosaccharides and polysaccharides.
Monosaccharide (Gk: mono- one)
A monosaccharide is the most basic form of carbohydrates with a single sugar molecule. It is
also called a simple carbohydrage. Monosaccharides are composed of 3-7 carbon atoms. The
common monosaccharides are glucose, fructose, galactose, ribose and deoxyribose.
Monosaccharides are sweet in taste and soluble in water. The general formula of
monosaccharides is written as (CH2O)n; where, n= 3 to 7. For example, when n=6, (CH2O)n =
C6H12O6 (Glucose)
HOP ;O; - JH
H'H'H
OH
H
Glucose
Fructose
H
H
OH
Galactose
OH
H
Deoxyribose
OH
OH
Ribose
Oligosaccharides
Oligosaccharide is a type of sugar containing a chain of 2-10 monosaccharides. Disaccharide is
one of the examples of oligosaccharides.
Disaccharides (Gk: di- two): A carbohydrate consisting of two sugar molecules is
called a diasaccharide. In a disaccharide, two monosaccharides are joined together by a
glycosidic bond. A glycosidic bond is a type of covalent bond that joins a carbohydrate
(sugar) molecule to another group.
250
Optional Science - 10
BIOLOGY
The common disaccharides are maltose (glucose + glucose), lactose (glucose + galactose)
and sucrose (glucose + fructose). It is sweet in taste and soluble in water.
~
ON
M
H
OH
HO
HOCH 2
HOT H'
0
~
CIH H
H
H
'
H
OH
Glucose
Glucose
I
Maltose
Polysaccharide (Gk: poly- many)
~
o "-J
H
OH
Galactose
OH
H
H
OH
Glucose
I
lactose
~
0
H
OH
OH
Glucose
H
Fructose
Sucrose
A polysaccharide is a polymer formed by many monosaccharides joined together by a
glycosidic bond. It is also called a complex carbohydrate. They are usually tasteless and
insoluble in water. The common polysaccharides are starch, glycogen, cellulose and chitin.
Sources of Carbohydrates
The large number of carbohydrates stored by plants are a rich source of food and energy for
all life. A number of complex carbohydrates in plants are formed from glucose. The foods
that are rich in carbohydrates are known as starchy foods. They are found in legumes, rice,
wheat, corns, whole grain breads, cereals and starchy vegetables like potato, carrot, sugar beet,
etc. They are also found in fruits like sugarcane, pineapple, milk and milk products. Some
processed foods like candy, carbonated beverages and table sugar also contain carbohydrates.
Importance of Carbohydrates
Carbohydrates are of great importance in biology. The biological breakdown of carbohydrates
into glucose supplies energy to every living organism in conducting various metabolic
processes.
The importance of carbohydrates are:
1.
Carbohydrates are macronutrients that build body strength and serve as excellent
energy providers.
2.
Cellulose fiber (i.e., a polysaccharide) is the primary structural component of plants.
cell walls are primarily made up of cellulose.
3.
The fibers present in carbohydrates promote regular bowel movement and help to
control constipation.
4.
Cellulose is the major component of cotton fiber and wood. Paper and clothes are made
from cellulose.
Memory Plus
The calorific value of carbohydrate is 4.1 kcal/g, i.e. one gm of carbohydrates gives 4.1
kcal energy on its complete breakdown or oxidation. In case of a normal healthy person,
the average intake of carbohydrates is 500g per day (i.e., 2050 kcal/day).
Lipids
Lipids are the naturally occuring organic compounds commonly known as fats or oils and
their derivatives. Chemically, lipids are esters of fatty acids. They are non-polar organic
compounds. So lipids are insoluble in polar solvent like water but soluble in organic solvents
like alcohol, ether, etc. Lipids are the energy storing molecules. They provide energy for life.
BIOLOGY
Optional Science - 10
0
251
Classification of Lipids
Based on structure, lipids are broadly classified into simple, complex and derived lipids.
1.
Simple lipids : Simple lipids are esters of fatty acids with alcohols. Fats (monoglyceride,
diglyceride, triglyceride etc.) and waxes are simple lipids. Oils are fats in the liquid state.
2.
Complex lipids: Complex lipids are esters of fatty acids with alcohol and containing other
groups like phosphate, carbohydrates, proteins, nitrogenous base, etc. They are formed
by the combination of lipid with the non-lipid molecule. For example: phospholipids
(lipids + phosphates), glycolipids (lipids + carbohydrates), lipoproteins (lipids + protein),
etc.
3.
Derived lipids: Derived lipids are the compounds derived from simple and compound
lipids by hydrolysis. For example: glycerol, fatty acids, steroids (cholesterol), hormones.
Sources of lipids
Both plant and animal sources contain different types of lipids. Lipids can be obtained in a
large amount from meat, butter, cheese, milk, eggs, ghee, nuts, avocados, etc.
Importance of lipids:
1.
Lipids are an excellent reservoir of energy for the body.
2.
Lipids are a source of fat-soluble vitamins (A, D, E and K).
3.
Lipids protect the internal organs.
4.
Lipids (fat) act as an insulator.
5.
Lipids form the cell membrane. Phospholipids regulate the permeability of the cell
membrane.
Protein
Proteins are large, complex nitrogen-containing organic compounds composed of one or more
long chains of amino acids. They are important macromolecule in a living organism. Protein
builds and repairs body tissue. It also forms antibodies, hemoglobin, enzymes and hormones.
So proteins are also known as the building blocks of life. It protects and provides structure
to the body of a multi-cellular organism in the form of skin, hair, cartilage, ligaments and
tendons.
Proteins are found throughout the body. Trypsin, pepsin, collagen, keratin, insulin, thrombin,
fibrinogens, albumin, globulin, hormones, etc. are some biologically important proteins.
Proteins are made up of 20 different amino acids. When proteins are broken down into amino
acids, the body uses these amino acids to make new proteins.
Fact with reason
Proteins are known as building blocks of life, why?
Proteins are required for structure, function and regulation of each and every organ,
tissue and cells of the body. They are essential to make new cells, repair the damaged
tissue and cells. Proteins are engaged in all the biochemical reactions taking place in the
cells. The body needs proteins for growth and development. So proteins are known as
building blocks of life.
252
Optional Science - 10
BIOLOGY
Amino Acids
Amino acids are organic biomolecules that are attached to each other to form long chains
of proteins. They are known as the building blocks of proteins. Proteins are made up of
carbon, hydrogen, oxygen, nitrogen and with, or without, sulphur. Amino acids perform
several biological and chemical functions in a human body. Amino acids colourless crystalline
substances. They are generally soluble in water and insoluble in non-polar organic solvents.
Classification of amino acids
Most of the amino acids are not synthesized by the body. They must be obtained from food.
Therefore, 20 different amino acids can be classified on the basis of that whether people can
acquire them through diet or not. On the basis of nutrition, amino acids are of three types:
1.
Essential amino acids: Amino acids that cannot be synthesized in the body and should
be supplied through diet are called essential amino acids. The essential amino acids are
obtained from eggs, milk, meat, fish and poultry. The eight essential amino acids are
valine, leuine, methionine, lysine, isoleucine, phenylalamine, threonine and tryptophan.
2.
Non-essential amino acids: Amino acids that are synthesized in the human body either
from essential amino acids or from normal protein breakdowns are called non-essential
amino acids. Ten non-essential amino acids include: alanine, serine, glycine, glutamine,
tyrosine, aspartic acid, cysteine, proline, glutamic acid and asparagine.
3.
Semi-essential amino acids: Amino acids which can partly synthesized in adult human
body but are necessary to supply through diet in infants are called semi-essential amino
acids. These amino acids are only required by lactating or pregnant women and growing
children. The two semi-essential amino acids are histidine and arginine.
Classification of Proteins
Proteins can be classified in different ways. On the basis of nutritional value of dietary proteins,
they are classified as first class proteins and second class proteins.
1.
First Class Proteins : Proteins that contain all the essential amino acids are called first
class proteins. These are also known as complete proteins. First class proteins are of
animal sources like meat, fish, dairy, eggs, etc.
2.
Second Class Proteins : Proteins that are deficient in one or more essential amino acids
are called second class proteins. These are also known as incomplete proteins. Plant
proteins are generally second class proteins.
Sources of Protein
Proteins should be included in our daily diet for proper growth of our body. Foods rich in
proteins include vegetables like beans, carrot, cabbage, onion, cucumber, beetroot and green
leafy vegetables. Fruits like melon, orange, pineapple, papaya, grapes and pomegranate
contain protein. Eggs, groundnuts, peanuts, whitefish, pork, mustard seeds, chia seeds,
almond, walnut, cashew are also good sources of proteins.
Memory Plus
The calorific value of protein is 5.65 kcal/g, The average adult needs about 70-100 grams
of protein per day.
Marasmus and kwashiorkor usually occur in young children and babies due to deficiency
of protein.
BIOLOGY
Optional Science - 10
0
253
Fact with reason
Vegetarians must take special care of dietary to meet their protein need, why?
Plants, by themselves, do not provide all the essential amino acids, but they provide
amino acids in combination with other vegetarian food sources. For example, when
cereals are combined with pulses, they provide most of the essential amino acids.
Vegetarians must take special care to ensure that their body requirement of protein is
sufficiently met by their diet.
Importance of Protein
1.
Some proteins are hormones. They regulate many body functions.
3.
Some proteins act as antibodies. They protect our body from infections and disease
causing germs.
4.
Proteins are the structural elements of cells and tissues. They help in building and
repairing cells.
5.
Proteins make up bones, muscles, hair and other parts of the body.
6.
Proteins act as enzymes. They catalyze the biochemical reactions in the body.
Activity
Food Tests
Students can test a variety of local fresh and dried foods for the following nutrients: fats,
protein, starch and glucose.
Test for fats:
Rub the food sample onto a piece of paper. If fat is present, it will make a translucent stain
on the paper.
Test for proteins (Biuret test)
1.
2.
3.
4.
If the food sample is not in liquid form, mash it up and add a little water to make a
suspension.
Add 2 - 3 drops of biuret reagent.
Shake well.
A purple color is seen if protein is present.
1.
2.
Add a few drops of iodine solution to the food sample.
If it turns into blue-black color, starch is present.
1.
If the food sample is not in liquid form, mash it up and add a little water to make a
suspension.
Place about 2ml of the food sample into a test tube and add an equal volume of
Benedict’s solution.
Place the tube in very hot water for a few minutes or heat the test tube directly for
a few minutes.
A yellow/green/orange or brick red precipitate develops if glucose is present.
Test for starch
Test for glucose (Benedict’s test)
2.
3.
4.
......
0
254
......... :
Optional Science - 10
BIOLOGY
Enzymes
Enzymes are large biomolecules that act as catalysts for biochemical reactions within living cells
in every plant and animal. They are involved in many chemical reactions that are necessary to
sustain life. Enzymes catalyse the chemical reactions that are involved in growth, respiration,
digestion, reproduction, etc. They only increase the rate of reaction without themselves being
changed. All enzymes are protein molecules. Some examples of common enzymes are lipases,
amylase, pepsin, protease, catalase, maltase, sucrase, rennin, etc.
Fact with reason
Enzymes are known as biological catalyst, why?
Enzymes are known as biological catalyst because they speeds up the chemical reaction
in cell. These reactions include respiration, digestion, photosynthesis, etc..
Enzyme Activity
Enzyme activity is affected by factors that disrupt protein structure. Factors that disrupt
protein structure include temperature and pH (high level of acid). The degree of temperature
and the level of acids required to break down the molecules of enzymes depends on the
strength of the bonds between amino acids. Once the bonds are degraded enzymes become
inactive or non-functional. The part of enzyme which acts as the catalyst is called active site of
the catalyst, whereas remaining part is called substrate.
Classification of Enzymes
Based on catalyzed reactions, the nomenclature committee of the International Union of
Biochemistry and Molecular Biology (IUBMB) classified enzymes into 6 groups as
1.
Oxidoreductase: Oxidoreductage helps in oxidation-reduction reaction. It catalyzes the
transfer of electrons from the reductant (electron donor) to the oxidant ( electron acceptor).
2.
Tansferase: Transferase enacts the transfer of specific functional groups (e.g. a methyl or
glycosyl group) from one molecule (donor) to another (acceptor).
3.
Hydrolase: Hydrolase uses water to break a chemical bond. This results in a division of a
larger molecule to smaller molecules.
4.
Lyases: Lyase Catalyzes the breaking of various chemical bonds and forms a new double
bond or a new ring structure.
5.
Isomerase: Isomerase catalyzes the formation isomer from the substrate of enzyme
molecule. It facilitates the transfer of specific functional groups intramolecularly without
adding or removing atoms from the substrate.
6.
Ligases: Ligase catalyzes the joining of two large molecules by forming a new chemical
bond. It plays an essential role in DNA replication.
Characteristics of Enzymes
Enzymes have some characteristics as follows.
1.
Enzymes are protein molecules.
2.
They act as a biological catalyst.
BIOLOGY
Optional Science - 10
255
4.
Enzyme activity can be controlled. Their activity is high at optimum temperature.
Most human enzymes have an optimum temperature around 40°C.
5.
Enzymes denature at high temperatures, in alcohol, in concentrated acids, etc.
Sources of Enzymes
Enzymes are present in the food we eat. Raw fruits and vegetables are a good source of
enzymes. Fruits and vegetables rich in enzymes are apples, apricots, asparagus, avocados,
bananas, beans, beet, broccoli, cabbage, carrots, celery, cherry, cucumber, figs, garlic, ginger,
grapes, green barley grass, kiwi.
Memory Plus
Canned or processed (drying, freezing, irradiation) food kills the enzymes. Food that is
whole and uncooked and unpasteurized milk will provide enough enzymes.
Functions of Enzymes
Enzymes have various biological functions in living organisms. They also have industrial
applications when extremely specific catalysts are required.
Biological Functions of Enzymes
1.
2.
3.
4.
5.
Enzymes like amylase and protease play an important role in digestion.
Some enzymes get activated as a part of signal transduction possess.
They help in the muscle contraction.
Enzymes present in pathogens are for infecting cells.
Enzymes can break large molecules into small molecules.
Industrial Applications of Enzymes
Enzymes are mostly used in the food, beer and dairy industry.
1.
Enzymes from barley are widely used in breweries.
2.
Rennin is used to manufacture cheese.
3.
Enzymes like cellulose and pectinase are used to clarify fruit juices.
4.
Enzymes are used in forensic science and molecular biology.
5.
Amylases convert starch into glucose. They are used in the production of sugars from
starch.
6.
Catalase is employed in the rubber industry to form oxygen, which converts latex to
foam rubber.
Memory Plus
The human body contains about 3,000 enzymes that are constantly regenerating, repairing
and protecting us. Enzymes are specific in function. They function with only one reactant
to produce a specific product.
Nucleic Acids
Nucleic acids are large organic compounds found in the chromosomes of living cells and
viruses. They are also one of the most important biological macromolecules in all living
beings. Nucleic acids are found either in a free-state or bound to proteins as nucleoproteins.
They are a linear polymer of nucleotides.
256
Optional Science - 10
BIOLOGY
Nucleotides and their structure
. ~xs
Nucleotides are made up of pentose sugar,
a nitrogenous base and a phosphate group.
Nucleosides are structural subunits of nucleic
2
O= r - O - C
~
Nitrogenous
acids. It is made up of nitrogenous base attached
0H
H
(adb:~i~e)
Phosphate
H
H
to a pentose sugar. A nitrogenous base is simply
group
OH H
Sugar
a nitrogen-containing molecule that has the same
General Structure
Structure of Adenine
chemical properties as a base. There are five types
of nitrogenous bases. Two of these bases are purine and the other three are pyrimidine.
I
N
N
H
Purine: Purine bases have a double-ring structure. These are adenine(A) and guanine(G).
Pyrimidine: Pyrimidine bases have a single-ring structure. These are cytosine(C),
thymine(T), and uracil(U).
Types of Nucleic Acids
There are two types of nucleic acids: deoxyribonucleic acid (DNA) and ribonucleic acid (RNA).
DNA (deoxyribonucleic acid): DNA is a double helical macromolecule. It contains
genetic information. The nitrogenous bases in DNA are A, C, G and T. The DNA
segments carrying genetic information are called genes. DNA is found inside the cells
in long structures called chromosomes.
RNA (ribonucleic acid): RNA is a single stranded macromolecule that is essential for
protein synthesis in organisms. It contains genetic information in some viruses. The
nitrogenous bases in RNA are A, C, G and U. There are three types of RNA: transfer
RNA (tRNA), messenger RNA (mRNA) and ribosomal RNA (rRNA).
Importance of nucleic acids
1.
Nucleic acids store and transfer genetic information.
2.
They control the development of an individual.
3.
Mutation results from deletion, addition and replication of nitrogen bases of DNA,
which help to form variants.
4.
DNA controls the synthesis of RNA in a cell and RNA directs the synthesis of proteins.
Inorganic Compounds
Minerals
Minerals are essential inorganic nutrients for organisms to perform functions necessary for
life. Inorganic biomolecules are minerals. There are 24 elements that are used in our body.
There are eight major elements essential for growth and development of living beings.
Such elements are called essential elements. They are sodium, chlorine, potassium, calcium,
phosphorus, nitrogen, sulphur and magnesium. These elements are also known as macro
elements. Some elements like fluorine, zinc, iodine, iron are needed in trace amounts. These
elements are known as trace elements. These minerals are important for the well-being of
the human body. They have various functions like formation of tissues, conduction of nerve
impulses, formation of blood, etc. We obtain minerals from plants as they absorb them from
the soil.
BIOLOGY
Optional Science - 10
0
257
Water
Water is the main components of cell. It makes about 60-90% of the total chemical content of
the cell. It is responsible for the living nature of cell. It is found in two forms: free form that can
be used for metabolic processes and bound form that is bound with other molecules. Nearly
95% of water occuring in cells is found in the free state. While 5% is in the bound state to other
molecules.
Importance of water
1.
2.
3.
It is the universal solvent.
Different metabolic reactions like digestion, photosynthesis requires water.
It aids in the movement of plant organs like opening and closing of stomata, dehiscence
of fruits, etc.
Water helps to transport materials from one cell to another.
Water maintains turgidity of cell.
4.
5.
Answer writing skill
1.
Define biomolecules.
Biomolecules are organic molecules present in living things and are involved in the
growth, repair and metabolic process of living organism. For example: carbohydrate,
protein, lipid, etc.
What are polysaccharides?
Polysaccharidesarea complex carbohydrate formed by many monosaccharides joined
together by a glycosidic bond. They are usually tasteless and non-soluble in water.
Example: starch, glycogen, cellulose and chitin.
List the name of essential aminoacids.
Essential amino acids are valine, leuine, methionine, lysine, isoleucine, phenylalamine,
threonine and tryptophan.
Write down the differences between monosaccharides and disaccharides.
2.
3.
4.
Monosaccharide
Disaccharide
Monosaccharide consists of a single sugar Disaccharide
consists
of
two
molecule.
monosaccharides.
It is the simplest form of carbohydrate.
It is a complex form of carbohydrate.
Example: glucose, frutose, galactose, etc. Example: maltose (glucose + glucose),
lactose (glucose + galactose) and sucrose
(glucose + fructose).
Write short notes on minerals.
Minerals are inorganic biomolecules. Minerals are important for the well-being of
the human body. We obtain minerals from plants as they absorb them from the soil.
Essential minerals may be categorized into macro elements and micro elements.
Macro elements are the major minerals required in sufficient amounts in our diet.
5.
0
258
Optional Science - 10
BIOLOGY
They are sodium, chlorine, potassium, calcium, phosphorous, sulphur and magnesium.
Some elements needed in trace amounts are known as micro elements. They are
fluorine, zinc, iodine, iron etc. The functions of minerals are:
1. Formation of tissues.
2. Conduction of nerve impulses.
3. Formation of blood.
6.
7.
8.
Differentiate between simple and derived lipids.
Simple lipids are esters of fatty acids with alcohols,whereas derived lipids are obtained
by the hydrolysis of simple and compound lipids. Examples of simple lipids are fats,
oils and waxes while derived lipids are glycerol, fatty acids, steroid hormones, etc.
What is the significance of enzymes?
Enzymes are biocatalysts, which help to speed up the chemical reaction during different
metabolic processes like digestion, respiration, photosynthesis, etc. inside the cells. The
significance of enzymes is as follows:
1. Enzymes like amylase and protease play an important role in digestion.
2. Enzymes present in pathogens are usedfor infecting cells.
3. Enzymes from barely are widely used in breweries.
4. Rennin is used to manufacture cheese.
5. Enzymes like cellulose and pectinase are used to clarify fruit juices.
6. Enzymes are used in forensic science and molecular biology.
What is a carbohydrate? What are its types? Write any two importances of carbohydrates.
A carbohydrate is the most abundant biomolecule that contains carbon, hydrogen and
oxygen as its main elements. The general formula of carbohydrate is written as (CH2O)
n. Carbohydrates are often referred to as sugars or saccharides.
There are three main types of carbohydrates on the basis of the number of sugar units.
They are monosaccharides, oligosacharides and polysaccharides.
Monosaccharide: A monosaccharide is the simplest group of carbohydrate. It consists
of a single sugar molecule. It is sweet in taste and soluble in water. Example: glucose,
fructose, galactose, ribose and deoxyribose.
Oligosacchaside: Oligosacchasids si a type of sugar containing a .2-10 monosccnorides.
Disaccharide: Disaccharides are formed by two monosaccharides joined together by a
glycosidic bond. It is sweet in taste and soluble in water. Example: maltose (glucose +
glucose), lactose (glucose + galactose) and sucrose (glucose + fructose).
Polysaccharide: A polysaccharide is a complex carbohydrate formed by many
monosaccharides joined together by a glycosidic bond. It is usually tasteless and nonsoluble in water. Example: starch, glycogen, cellulose and chitin.
The two importances of carbohydrate are:
1.
Carbohydrates are macronutrients that build body strength and serve as excellent
energy providers.
2.
The fibers present in carbohydrates help to control constipation.
BIOLOGY
Optional Science - 10
259
Exercise
Section "A"
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
Define biomolecules with example.
What are carbohydrates?
Define each of the followings:
a. monosaccharides
b. disaccharides
c. oligosaccharides
d. polysaccharides
Write two examples of each of the followings:
a. Monosaccharides
b. oligosaccharides
c. Polysaccharides
What are the component sugar molecules in each of the followings:
a. Maltose
b. lactose
c. sucrose
What are lipids?
What are derived lipids?
Write two examples of each of followings:
a. Simple lipid
b. complex lipid
c. derived lipids
What are proteins?
Give name of some biologically important proteins.
What are amino acids?
How many types of amino acids are there that make up proteins?
What are semi-essential amino acids?
What is the calorific value of each of protein and carbohydrates?
Name two malnutrition in young children and babies due to deficiency of protein.
What are enzymes? Write two examples?
What is nucleic acid?
Name two essential elements and two trace elements that are found in human body.
Section "B"
1.
What are the sources of lipid?
2.
Differentiate between essential amino acid and non-essential amino acid.
3.
Write two differences between simple lipids and complex lipid.
260
Optional Science - 10
BIOLOGY
4.
Egg is considered as a reference protein, why?
5.
Why do athletes, laborer, etc. need high carbohydrate in their diet?
6.
Proteins are known as building blocks of life, why?
7.
Write any two importance of each of protein, carbohydrate and nucleic acid each.
8.
Write two differences between essential amino acids and non-essential amino acids.
9.
Write two differences between first class protein and second class proteins.
10.
Write importance of enzymes.
11.
Vegetarians must take special care of dietary to meet their protein need, why?
12.
Write any four characteristics of enzymes.
13.
List six different groups of enzymes.
14.
Write two differences between essential elements and trace elements.
Section "C"
1.
What roles do the proteins play in our body?
2.
3.
4.
Write a brief note on carbohydrate.
Write in short about sources of carbohydrates.
How can we fulfill the need of proteins in our body through diet? Write on the
basis of its different sources.
Explain in short about the factors that affect enzyme activity.
Write three biological functions of enzymes.
Write three industrial applications of enzymes?
Write three importance of nucleic acids.
5.
6.
7.
8.
Section "D"
1.
2.
3.
4.
5.
6.
What is the role of enzymes in the body of living organisms? Explain in brief.
Explain in brief about the importance of biomolecules in our daily life.
Enzymes are called bio-catalyst. Explain.
‘Human diet must be a balanced diet’. Justify it on the basis of your learnings
about biomolecules.
Explain in brief about nucleotide and its structure.
Mention the role of inorganic compounds in the body of living organisms.
BIOLOGY
Optional Science - 10
0
261
Multiple choice questions
1.
2.
3.
4.
5.
6.
There are ……… types of essential amino acids in the nature.
a.8
b. 12
c. 20
d. 10
Lactose is a combination of
a. glucose + glucose
b. fructose + galactose
c. glucose + fructose
d. glucose + galactose
In which of the following group are all polysaccharides?
a. sucrose, glucose and fructose
b. maltose, lactose and fructose
c. glycogen, sucrose and maltose
d. glycogen, cellulose and starch
In RNA, thymine is replaced by
a. adenine
b. guanine
c. cytosine
d. uracil
Glycogen is an example of
a. monosaccharides
b. disaccharides
c. oligosaccharides
d. polysaccharides
Kwashiorkor is due to the deficiency of:
a. carbohydrates
b. lipid
c. proteins d. nucleic acid
Project Work
Work in a group to make a chart on a cardboard. Collect information of different
biomolecules including their structure, sources, types, functions, etc. Finally present your
work in the classroom.
262
Optional Science - 10
BIOLOGY
UNIT
14
CELL BIOLOGY
Rudolf Ludwig Carl Virchow (1821-1902) was a German physician, anthropologist,
pathologist, prehistorian, biologist, writer, editor and politician, known for his advancements
in public health. He is known as the Father of modern pathology as his work brings more
science to medicine. He is also called founder of social medicine and veterinary pathology.
.......................................................,.,. '' ' .........................................................................
Syllabus issued by CDC
Theory
Practical
9
3
Learning objectives:
At the end of this unit, the students will be able to:
• describe the types and functions of plant tissue
and animal tissue.
• describe the structure of the root and stem of a
monocot and dicot plant by observing them.
Key terms and terminologies of the unit
1.
Cell biology: Cell biology is a branch of life science that deals with the study of cell
structure, its functions and its chemistry.
2.
Tissue: A tissue can be defined as a cluster of cells, similar in structure and performing
a particular function.
3.
Epithelial tissue: Epithelial tissue is the membranous animal tissue with one or more
layers of closely packed cells that forms the outer covering or lining part of the body,
including bodily cavities and vessels.
4.
Simple epithelium: An epithelial tissue with a single layer of epithelial cells that are
in direct contact with the basement membrane is called simple epithelium.
5.
Compound epithelium: An epithelial tissue formed of several layers of epithelial
cells is called compound or stratified epithelium.
6.
Connective tissue: Tissues with cells embedded in an amorphous matrix that connect,
support, bind, or separate other tissues or organs are called connective tissues.
7.
Tendon: A parallel array of closely packed white fibrous tissues is called tendon.
8.
Ligament: A band of dense bundles made of yellow elastic fibers is called ligament.
BIOLOGY
Optional Science - 10
263
9.
Muscular tissue: Muscular tissues are the soft tissues capable of contraction and
relaxation which are made up of long cylindrical fibers arranged in a parallel way.
10.
Nervous tissue: Nervous tissue or neural tissue is the primary tissue composed of the
cells in the central nervous system and peripheral nervous system which is responsible
for receiving stimuli and transmitting signals to and from different parts of an organism.
11.
Stem: Stem is the vascular part of a plant above the ground consists of nodes and
internodes.
12.
Pectin: Pectin is a carbohydrate found mostly in the skin and core of a raw fruit.
13.
Lignin: An organic substance binding the cells, fibers and vessels, which constitute
wood and the lignified elements of plants.
14.
Vascular cambium: The secondary meristematic tissue that forms the vascular tissues
(xylem and phloem).
15.
Vascular bundle: A vascular bundle is a part of the transport system in vascular plants
16.
Root: A root is a vascular part of plant present normally underground.
17.
Cell division: Cell division is the process by which a mother cell divides into two or
more daughter cells.
18.
Cell cycle: The cell cycle is the sequence of changes that takes place in the cells during
cell growth and cell division.
19.
Interphase: Interphase is the stage during which a cell prepares, grows and accumulates
nutrients needed for cell division.
20.
Cytokinesis: Cytokinesis is the division of cytoplasm into two separate cells which
occurs concurrently with nuclear division in M-phase of cell cycle.
21.
Centriole: Centriole is a minute cylindrical organelle near the nucleus in animal cells,
occurring in pairs and involved in the development of spindle fibers in cell division.
22.
Chromatids: The two thread like strands into which a chromosome divides
longitudinally during cell division are called chromatids.
23.
Sister chromatids: 'one-half' of a duplicated chromosome is called sister chromatid.
24.
Mitosis: Mitosis is the division of a mother cell into two daughter cells with equal
number of chromosomes to that in mother cell.
25.
Somatic cells: All the body cells of an organism that are responsible for growth and
development of the body, except the gametes (sperm or ovum) are called somatic cells.
26.
Meiosis: Meiosis is the division of a mother cell into four daughter cells (sex cells or
gametes) each having half number of chromosomes than that in the mother cell.
27.
Synapsis: The process of pairing up of homologous chromosomes to form a bivalent is
called synapsis.
28.
Chiasmata: The points of contact between two non-sister chromatids are called the
chiasmata
29.
Crossing-over: The process of exchange of genetic material from the chiasmata in
between two non-sister chromatids of homologous pair is called crossing over.
30.
Terminalization: The process of movement of chiasmata towards the end of the
chromosome and disappear is called terminalization.
0
264
Optional Science - 10
BIOLOGY
Introduction
The cell is the structural and fundamental unit of life. Cell biology is a branch of life science
that deals with the study of cell structure, its functions and its chemistry. Cell biology is also
termed as cytology. The term cytology was derived from two Greek words; kytos, which
means hollow, vessel an logos, which means study.
Cell biology is concerned with the physiological properties, metabolic processes, signaling
pathways, life cycle, chemical composition and interactions of the cell with their environment.
Cells organize in a specific way to give structure of tissues. In this unit we will learn about
animal tissues, plant tissues, structure of roots and stem of each of monocot plants and dicot
plants. We will also learn about the two different types of cell division (mitosis and meiosis)
that occurs in body cells with their significance in life processes.
Tissue
Tissues are absent in unicellular organisms. Multicellular animals and plants have tissues that
organize and regulate their response to their environment. The word tissue is derived from a
latin word 'tissu' which means 'weave'. Cells are woven together to form tissues. A tissue consists
of a group of structurally and functionally similar cells. Therefore, a tissue can be defined as a
cluster of cells, similar in structure and performing a particular function. The study of tissues
is called histology.
Animal Tissue
There are four types of tissues found in animals. They are: epithelial tissue, connective tissue,
muscular tissue and nervous tissue (Nevral tissue).
Animal Tissues
Epithelial Tissue
Simple epithelium
Simple
squamous
Simple
cuboidal
Connective Tissue
Stratified epithelium
Skeletal muscle
Loose connective
Simple
columnar
Muscular Tissue
Areolar
Adipose
Nervous Tissue
Smooth muscle
Cardiac muscle
Dense connective Specialized connective
White fibrous
Fluid connective
Yellow fibrous Cartilage
•
t
.~---L=====-------=~-==='..-=;===--==~
.____ ___.I .__I_ __.I .__I~_____. ~-~I ~I- ~ I =1
Ciliated cuboidal
Brush bordered
Stratified squamous
f
Stratified cuboidal
*
Keratinized epithelium
Ciliated columnar
Brush bordered columnar
Stratified columnar
i
::===
Transitional epithelium
Non-keratinized epithelium
Glandular columnar
BIOLOGY
Bones
~
Blood
Optional Science - 10
Lymph
0
265
A.
Epithelial Tissue (Epithelium)
There are group of cells in our body that cover the surface of organs, such as the surface of
the skin, reproductive tract, airways and inner linings of the digestive tract, etc. Such a group
of cells forms an epithelial tissue. Epithelial tissue is the membranous animal tissue with one
or more layers of closely packed cells that forms the outer covering or lining part of the body,
including bodily cavities and vessels. This tissue provides a barrier between the external
environment and the organ it covers.
Characteristics: Epithelial tissue is composed of tightly packed cells. It lacks blood vessels but
supplied with nerve fiber. It has a high regenerative ability.
Types of epithelial Tissue: On the basis of layers of cells in the epithelial tissues, there are two
types of epithelial tissues: simple epithelium and compound epithelium.
1.
Simple epithelium
An epithelial tissue with a single layer of epithelial cells that are in direct contact with the
basement membrane is called simple epithelium. It functions as a lining of cavities of
body, ducts and tubes. On the basis of structural modification the simple epithelium is
divided into three types: Simple squamous epithelium, Simple cuboidal epithelium and
Simple columnar epithelium.
a.
Simple Squamous epithelium: This tissue contains thin, flat
and polygonal cells in a single layer with irregular margins.
Cells have an oval nucleus in the middle part. They are
arranged like the tiles on a floor. Therefore, it is also known
as pavement epithelium.
fig: Simple squamous epithelium
It forms the lining of the coelom, buccal cavity, walls of blood vessels, Bowman’s capsule
of nephron in kidney and alveoli of lungs. It helps in the protection, absorption,
ultrafiltration and exchange of gases.
Fact with reason
Simple squamous epithelium is also called pavement epithelium, why?
In simple squamous epithelium, cells are flat with flattened and oblong nuclei. It has a
tile-like appearance. So, it is also called pavement epithelium.
b.
Simple Cuboidal epithelium: This tissue contains cubical
cells in a single layer. Cells have a round nucleus at the
center. It is found in the lining of many ducts of the
kidney, glands, testis, ovary, etc. and tubules of nephrons.
It helps in secretion, absorption and excretion. There are
two types of cuboidal epithelial tissue: ciliated cuboidal
and brush bordered cuboidal.
fig: Simple cuboidal epithelium
i. Ciliated cuboidal: The cuboidal cell having cilia on the free surfaces is called a ciliated
cuboidal cell. Cilia help in the conduction of mucus and other substances. It is located
on the ducts of nephrons.
ii. Brush bordered cuboidal: The cuboidal cell having microvilli on the free surfaces is
called a brush bordered cuboidal cell.
266
Optional Science - 10
BIOLOGY
c.
Simple Columnar epithelium: This tissue contains elongated cells
in a single layer. They are placed side by side like columns. An
elongated nucleus is located at the basal end of the cell. The free
surface of these cells may have microvilli. It forms the lining of the
stomach, gastric glands, intestinal glands, gall bladder, ureter and
uterine wall. There are three types of columnar epithelium:
fig: simple columnar
epithelium
i. Ciliated columnar epithelium: Columnar cell having cilia
cilia
on the free surface is called a ciliated columnar cell. It is
present in the fallopian tubes, bronchioles, spinal cord. It
nucleus
secretes mucus and helps in the movement of particles in a
fig: Ciliated columnar epithelium
specific direction.
ii. Brush bordered columnar epithelium: Columnar cell having microvilli on the free
surfaces is called a brush bordered columnar cell. It is present in intestinal mucosa. It
helps to increase the surface area for absorption.
iii. Glandular columnar epithelium: It is made up of modified columnar or cuboidal
cells. It helps in the secretion of chemical substances. It is found in the liver, pancreas,
mammary glands, sweat glands. It forms glands.
Memory Plus
Pseudostratified columnar epithelium is formed by a single layer of cells that
gives an appearance of being made from multiple layers when we look at
cross-section. The nuclei of such epithelial cells are at different levels leading
to the illusion of being stratified. Pseudostratified columnar epithelium
fig: Pseudostratified
tissue is found mostly in the inner walls of upper respiratory tract (nose,columnar
epithelium
trachea, bronchi) and hence also called as respiratory columnar epithelium.
2.
Compound or stratified epithelium
An epithelial tissue formed of several layers of epithelial cells is called compound or
stratified epithelium. It is also called multi-layered tissue. Basement membranes are usually
absent in compound epithelium. Its main function is to protect underlying structure from
mechanical wear and tear. Compound epithelium covers dry surface of skin, moist surface of
buccal cavity, pharynx and inner lining of salivary glands. Compound epithelium are of
following types:
a.
Stratified squamous epithelium: It is made up of several layers
of cells. The upper layer is made up of squamous cells. The
lower layer is made up of germinative columnar or cuboidal
cells. The stratified squamous epithelium is of two types:
fig: Stratified squamous epithelium
i. Keratinized epithelium: This tissue contains a protein called keratin in its upper layer.
This layer is hard. It makes the layer water proof. It is present in outer dry surfaces of
the body like hair, claws and nails. Keratinized epithelium is resistant to friction and
bacterial infections.
ii. Non-keratinized epithelium: The upper layer of this tissue contains living cells. Due
to the absence of keratin, this layer becomes wet. It is present on wet surfaces like
buccal cavity, pharynx, oesophagus and vagina. Non-keratinized epithelium protects
the surface from drying.
BIOLOGY
Optional Science - 10
267
b.
Stratified cuboidal epithelium: The upper layer of this tissue is
made up of cuboidal cells. The lower layer is made up of either
germinative columnar or squamous cell. The word germinative
indicates the outward growth of cells to the surface. Stratified
cuboidal epithelium is found in the lining of ducts of sweat glands,
salivary glands, mammary galnds, conjunctiva of eyes, etc. It helps
to circulate nutrients and increase absorption.
fig: Stratified cuboidal
epithelium
c.
Stratified columnar epithelium: The upper layer of this tissue is
made up of columnar cells. The lower layer is made up of germinative
cuboidal cells. It is found in the lining of vasa deferntia, male urethra,
trachea, bronchii, etc. It helps in protection and secretion.
d.
Transitional epithelium: This tissue is made up of several layers of
cells. The cells in the upper layer are dome shaped. The cells in the
middle layer are club shaped. The cells in the basal layer are cuboidal
Basement
Basal
in shape. This tissue has the ability to stretch and relax. It helps in
Membrane
Cells
fig:
transitional
epithelium
the expansion of the organ. It is found in the urinary bladder and
ureter.
Dome Cell
Function of epithelial tissue
Following are the important functions of epithelial tissues:
1.
2.
3.
It covers the body and makes lining of organs like lining of the mouth, alimentary canal, etc.
It helps to protect organs from microorganisms, injury and fluid loss.
It helps in absorption of water and nutrients. For eg., epithelial tissues in the wall of
intestine help in absorption of water and nutrients.
It helps in the elimination of waste from the body. For eg., epithelial tissues in kidneys
help to excrete wastes).
It secrets enzymes and hormones in the glands. For eg., epithelial tissues in glands help
to secrete hormones or enzymes.
4.
5.
B.
Connective tissue
The tissues with cells embedded in an amorphous matrix that connect, support, bind, or
separate other tissues or organs are called connective tissues. Connective tissues are fibrous
tissues. They are made up of a non-living material called extracellular matrix. This matrix can
be either liquid or rigid solid. Connective tissues give shape to organs and hold or connect
them in place. Example: blood, bone, tendon, ligament, adipose and aerolar tissues.
Types of Connective Tissues
There are four types of connective tissue: Loose connective tissue, Dense connective tissue,
Specialized or supportive connective tissue and Fluid connective tissue.
1.
Loose connective tissue: Loose connective tissue is the most common type of connective
tissue in vertebrates. It holds organs in place and attaches epithelial tissue to other
underlying tissues. A loose connective tissue has cells and fibres that are loosely arranged
in a jelly like substance containing white collagen fibers or yellow elastic fibers or both.
There are two types of loose connective tissue: Areolar tissue and adipose tissue.
0
268
Optional Science - 10
BIOLOGY
a.
Areolar tissue: Areolar tissue contains loosely arranged matrix having fibers (white
collagen fibers and yellow elastic fibres) and cells. It contains cells like fibroblast,
macrophages, mast cell, fat cells and
Reticular
Mast cell
fibers
lymphocytes. It is present beneath the
Elastic
Fixed
fibers
macrophage
skin, between and around the muscles,
Antibody
Free
macrophage
blood vessels, alimentary canal, producing cell
Collagen
fibers
respiratory tract, etc. It forms the
Blood in
Fibroblast
vessel
Stem cell
basement membrane of epithelium.
A~~1r:)
Functions:
i.
It binds the skin with the muscles.
ii.
It helps in healing wounds.
b.
White blood
cell
fig: Areolar tissue
Adipose tissue: It contains large
amounts of fat cells (adipocytes).
Fibers are fewer in amounts or absent
in adepose tissue. This tissue is found
below the skin, around the heart, kidney
and eye ball.
Functions:
2.
Ground substance
i.
It regulates the body temperature.
ii.
It stores fat.
iii.
It protects the organs from injury.
Adipose T issue
Nucleus _ _ _ ___,
fig: Adepose tissue
Dense connective tissue: Dense connective tissue has fibers as its main matrix element.
Fibers and fibroblasts are packed compactly in dense connective tissue. It forms strong,
rope-like structures such as tendons and ligaments. Dense connective tissue also make up
the lower layers of the skin (dermis). There are two types of dense connective tissue: white
fibrous tissue and yellow fibrous tissue.
a.
White fibrous tissue: It is a modified form of areolar tissue. It contains a thick layer
of white collagen fibers which are tough but non-elastic. These tissues are found as
a sheath in the pericardium of the heart, in brain (duramater), cornea of the eyeball,
coverings of the cartilage and bones. A parallel array of closely packed white fibrous
tissues is called tendon. It is a flexible but inelastic cord. Tendon attaches skeletal
muscles to bones.
Function: It provides mechanical protection when muscles are stretched.
b.
Yellow fibrous tissue: It is also a modified form of areolar tissue. It contains a thick
layer of elastic, flexible and closely packed yellow elastic fibers. These fibers are
straight and branched. A band of dense bundles made of yellow elastic fibers is
called ligament. They are more stretchy and contain more elastic fibers than tendons.
Ligaments connect bones to other bones at joints.
Function: It allows stretching and elasticity.
3.
Specialized connective tissue (Supportive connective tissue): These tissues form the
endoskeleton of vertebrates. They protect the delicate organs from different kinds of
injuries. Cartilage and bones are skeletal connective tissues.
BIOLOGY
Optional Science - 10
269
a.
Cartilage: It is a tough, smooth and flexible connective tissue. It is made up of
cartilage cells called chondrocytes. It is found on the tip of the nose, outer ear joints,
etc.
b.
Bones: It is a hard connective living tissue. It is made up of living bone cells called
osteocytes. It gives the structural frame to the body of vertebrates. The bone marrow
in some bones is the site of production of blood cells.
Memory Plus
Bones contains inorganic salts mainly calcium, phosphate and calcium carbonate.
4.
Fluid connective tissue: Fluid connective tissues are present in liquid form. They circulate
materials in the body, regulate the body temperature, minerals and water. They also
protect the body. Blood and lymph are fluid connective tissues.
a.
Blood: Blood is a red, viscous fluid connective tissue. It is slightly alkaline (pH 7.2-7.3)
in nature. It contains pale yellow plasma and three kinds of blood cells, or corpuscles.
The blood cells are the red blood cells (RBC), white blood cells (WBC) and platelets.
Functions:
b.
i.
It transports digested food materials, excretory
waste, hormones and respiratory gases inside
the body.
ii.
Platelets help in the coagulation of blood and
protect the body from excessive blood loss.
iii.
WBC provides defence against various diseases
and infections.
iv.
Blood helps to keep the body temperature stable.
_ • ._
___,,~white blood
Blood sample
platelets
fig: composition of blood
Lymph: Lymph is a transparent, slightly yellowish, alkaline fluid connective tissue.
It contains glucose, salts, amino acids and vitamins. Lymph is similar to the blood but
RBCs and some other proteins of blood are absent. It circulates in the body through
the lymph vessels.
Functions:
1.
It transports respiratory gases, food materials, hormones to the blood.
2.
It brings antibodies from the lymph nodes to the blood.
3.
It destroys pathogens and foreign particles.
Functions of connective tissue:
1.
2.
3.
4.
5.
6.
It binds and supports various tissues and organs in the body.
It helps to lessen the friction during the movement of the body organs.
It protects the body against infection.
Fat stored in adipose tissues forms an insulation in the body against heat loss.
Cartilage and bone give a definite shape to the body.
It stores and transports chemical substances in the body.
0
cells
270
Optional Science - 10
BIOLOGY
C.
Muscular tissue
Muscular tissues are the soft tissues capable of contraction and relaxation which are made
up of long cylindrical fibers arranged in a parallel way. These very fine contractile fibres
in muscular tissues are known as myofibrils. These are the basic functional unit of skeletal
muscle. The function of the myofibril is to perform muscle contraction.
Types of Muscular Tissues
There are three types of muscular tissue: Skeletal muscle, smooth muscle, and cardiac muscle.
1.
Skeletal muscle: Skeletal muscle
is a voluntary muscle. It is closely
attached to the bones. It helps in
the movement of the structures of
the body. It gives general support
and maintains the body’s posture.
It is also known as striated, or
striped, muscle.
Smooth
muscle
fibers
Junction
between
adjacent
cells
(a)
(c)
fig: (a) skeletal muscle (b) smooth muscle and (c) cardiac muscle
2.
Smooth muscle: Smooth muscle is an involuntary muscle. It is found in the inner linings
of organs visceral organs like blood vessels, urinary bladder, stomach, intestine, etc. It
helps in passing food materials and fluids. It is also known as unstriated, or unstriped
muscle.
3.
Cardiac muscle: Cardiac muscle is only found in the wall of heart. It is the most important
involuntary muscle. It works continuously without fatigue. Cardiac muscle helps our
heart to contract and relax. It helps the heart to pump blood through the heart. Cardiac
muscle looks like skeletal muscle (i.e. looks striated or striped). Unlike skeletal muscle the
contraction of cardiac muscle tissue is not in our control, so it is called involuntary.
Fact with reason
Skeletal muscle is called a voluntary muscle, why?
Skeletal muscle is called a voluntary muscle as the movement of this muscle is under
the control of our will.
Skeletal muscle is called a straited muscle, why?
Skeletal muscle has a repeating functional units. The presence of repeating functional
units results a series of bands visible along the muscle fibers. So, skeletal muscle is also
called a straited muscle.
Smooth muscle is also known as visceral muscle, why?
Smooth muscle is found in the walls of all visceral organs (the internal organs in the
main cavities of the body) except the heart. So, it is also known as visceral muscle.
Smooth muscle and cardiac muscle are called involuntary muscle, why?
The movement of smooth muscle and cardiac muscle is not in our control but under the
control of autonomic nervous system. So these muscle are called involuntary muscle.
BIOLOGY
Optional Science - 10
271
Function of Muscular Tissue
1.
2.
3.
4.
5.
The main function of muscular tissue is movement. Contraction of skeletal muscle
fibers causes the bone movement in our body.
The muscle provides the framework for the body and also helps in maintaining the
body posture.
The contraction of muscle produces heat, it helps to maintain a constant temperature of
the body.
Muscular tissue assists with the movement of cardiovascular and lymphatic vessels
through contractions.
Muscular tissue protect internal organs and contribute to joint stability.
D.
Nervous Tissue
Nervous tissue or neural tissue is the primary tissue
composed of the cells in the central nervous system
and peripheral nervous system which is responsible for
receiving stimuli and transmitting signals to and from
different parts of an organism. In the central nervous
system, neural tissues form the brain and spinal cord.
In the peripheral nervous system, neural tissues form
the cranial nerves and spinal nerves. Nervous tissue
consists of two main types of cells:
Dendrite
Nucleus
Cell body
Axon
Myelin sheath
Node of ranvier
Direction
of impulse
Axon terminal
Synapse
fig: Neuron
1.
Nerve cell: It is also known as neuron. It transmits electrical nerve impulses that move
information around the body.
2.
Neuroglia: Neuroglia are also known as glia. These are non-neuronal cells in the central
nervous system and peripheral nervous system. They provide support and protection
for neurons. Astrocytes, ependymal cells, microglial cells, oligodendrocytes and Schwann
cells are examples of glia.
Function of Muscular Tissue
1.
2.
3.
4.
Nervous tissues transmit message of external and internal stimuli. Neurons receive
signals from dendrites and send out through axon.
Neuroglia provide support, nutrition and insulation for the neurons.
Nervous tissues are responsible for controlling movements of specific parts of the body.
For example, for arm movement the nerve impulses are send to effector muscles in the
arm.
Nervous tissues work to stimulate activities that can occur at rest such as digestion,
waste excretion, etc.
Activity
Study the histological/permanent slides of different types of animal tissues under a
microscope. Draw a diagram along with the labelling and explain about the observed
tissues.
··cs-·····································
272
Optional Science - 10
.............................................................
BIOLOGY
Stem
Stem is the vascular part of a plant above the ground consists of nodes and internodes. It
comes under shoot of a plant that describes the new plant growth including stem, leaves and
flowers. Stem provides a pathway for transporting waters and miners in the plant body. It acts
as a storage site for carbohydrates.
The forms of stem may vary with plants: Cylindrical (it shows circular outline in transverse
section), Angular (it reveals three or four-angles in transverse section), Fistular (solid at the
nodes and hollow at the internodes), etc. On the basis of position with respect to the ground,
there are three types of stems: aerial, sub-aerial and underground stem.
Internal structure of a monocot stem
The internal structure of a monocot stem can be studied by taking a transverse section through
the internode of a monocot plant like grass, maize, bamboo, etc. A transverse section of a
monocot stem shows the following structure:
1. Epidermis
2. Hypodermis
3. Ground tissues
4. Vascular bundles
1.
Epidermis: The epidermis is the outermost covering of the stem. It is made up of a single
layer of compactly arranged barrel shaped parenchyma cells. Therefore, intercellular
spaces are absent. It is covered with a thick cuticle. It lacks trichomes (multicellular
hairs). It contains numerous openings called stomata. It plays a significant role in
protection.
2.
Hypodermis: The hypodermis
lies below the epidermis. It
is made up of two or three
layers of compactly arranged
sclerenchyma cells. Intercellular
spaces are absent in hypodermis
too. It provides mechanical
support to the plant.
3.
Epidermis
Hypodermis
Vascular
bundles
Ground
tissue
Epidermis
Hypodermis
Vascular
bundles
Xylem
Phloem
Ground
tissue
fig: Internal structure of moncot stem
Ground tissue: Ground tissue surrounds the vascular bundles. The major cells of the
ground tissue are parenchyma cells arranged in several layers which store nutrients.
In a monocotyledon stem, the ground tissue is not differentiated into the endodermis,
cortex and pericycle. It is represented by several layers of loosely arranged parenchyma
cells. It stores food.
Memory Plus
In some grasses, wheat, etc. the central portion of the ground tissue is hollow and is called
Pith cavity.
4.
Vascular bundles: A vascular bundle is a part of the transport system in vascular plants.
In monocot stem, vascular bundles are irregularly scattered in the ground tissue. The
bundles are younger and smaller in size towards the periphery and older and larger
towards the center. This type of arrangement of the vascular bundle is called centrifugal
arrangement. Each vascular bundle is covered by a single layer of sclerenchyma cells,
known as a bundle sheath.
BIOLOGY
Optional Science - 10
0
273
On the inner surface of the vascular bundle, xylem is found and towards its outer
surface phloem is found. Cambium is absent. These vascular bundles are described as
conjoint, collateral and closed.
a. Xylem: Xylem consists of tracheids,
vessels, xylem parenchyma and
xylem fibres. In the xylem, there are
two metaxylem and two protoxylem
vessels. These vessels are arranged in
the shape of 'Y'. The lower protoxylem
vessel are fused to form a cavity which
remains filled with water. It is known as
protoxylem cavity or lysigenous cavity.
Bund le Sheath
;;;::i,r;~~C:::Ji:ur -
Phloem
....;~ ff'~:"'.:l~- - Metaxylem
Protoxylem lacuna
Ground tissue
fig: Vascular bundles in monocot stem
b. Phloem: Phloem consists of sieve tubes, companion cells and phloem fibers. Phloem
parenchyma is absent in monocot vascular bundles.
Characteristic features of a monocot stem
1.
Epidermis is single layered and presence of a thick cutical.
2.
Absence of epidermal hairs (trichomes).
3.
Epidermis consists of stomata with guard cell.
4.
Presence of hypodermis made up of sclerenchyma cells.
5.
Ground tissues not differentiated into endodermis, cortex and pericycle.
6.
Vascular bundles are oval, conjoint, collateral and closed.
Internal structure of a dicot stem
A transverse section of a dicot stem shows the following structures:
1.
1. Epidermis
2. Hypodermis
3. Cortex
4. Endodermis
5. Pericycle
6. Vascular bundles
7. Cambium
8. Medullary rays
9. Pith
Epidermis
Epidermis: The epidermis is
Collenchyma
the outermost covering of the
Epidermal hair
Parenchyma
stem. It is made up of a single
Endodermis
Epidermis
Pericycle
Hypodermis
layer of compactly arranged
Parenchyma
barrel shaped parenchyma
Phloem
Endodermis
cells. Therefore, intercellular
Pericycle
Cambium
Metaxylem
spaces are absent. The cells are
Vascular
bundle
slightly thick walled. It consists
Medullary rays
Protoxylem
of numerous multicellular
Pith
projection called trichomes
Pith
(epidermal stem hairs). The
epidermis is covered by a thin
fig: Internal structure of dicot stem
transparent waxy covering called cuticle. This cuticle helps to prevent water loss. It also
contains stomata. Stomata are mainly involved in transpiration.
0
274
Optional Science - 10
BIOLOGY
2.
Hypodermis: The hypodermis is present just below the epidermis. It is made up of
four-five layers of collenchyma cells. These cells are compactly arranged. Therefore,
intercellular spaces are absent. The cells are thick walled due to the deposition of
cellulose and pectin. These cells contain chloroplast. Hypodermis provides mechanical
protection and additional support to the epidermis.
3.
Cortex: The cortex is made up of several layers of loosely arranged parenchyma cells.
Therefore, intercellular spaces are prominent. It may contain chloroplast which helps in
photosynthesis. Cortex is the major storage organ in the stem.
4.
Endodermis: The innermost layer of the cortex is called endodermis. It is wavy in
appearance. It is made up of compactly arranged barrel shaped parenchymatous cells.
Therefore, intercellular spaces are absent. These cells deposit more starch in the stem of
a dicot. Thus, the endodermis is also called a starch sheath.
5.
Pericycle: The pericycle lies just below the epidermis. It is made up of a few layers of
compactly arranged sclerenchyma and parenchyma cells. The pericycle forms a cap like
structure above each vascular bundle, known as a bundle cap.
6.
Vascular bundles: Vascular bundles are arranged in the form of a ring and are eight in
number. The vascular bundles are conjoint, collateral and open. Each vascular bundle
is made up of the phloem, cambium and xylem. The xylem is found on its inner surface
and phloem on the outer surface.
a. Xylem: Xylem lies toward the pith or center and composed of xylem vessels, tracheids,
xylem fibres (wood fibres) and xylem parenchyma (wood parenchyma). Protoxylem is
smaller with annular, reticulate or spiral thickenings, while metaxylem is wider with
pitted vessels.
a. Phloem: Phloem lies outside of the vascular bundle and composed of sieve tubes,
companion cells and phloem parenchyma. Companion cells are associated with sieve
tubes.
7.
Cambium: The phloem and xylem are separated by a meristematic tissue known as
cambium. Cambium is a thin strip of two or three layered cells which are radically
arranged. It forms a thin strip between xylem and phloem. Cambium is a type of
lateral meristematic tissues. So cambium increases the thickness of the plant through
secondary growth.
8.
Medullary rays: Medullary rays are parenchymatous, radially elongated or polygonal
cells. They are arranged radially. Medullary rays are part of the pith found between
vascular bundles. Their main function is to conduct food and water radially.
9.
Pith: It is the innermost part of the stem. The pith is made up of loosely arranged
parenchyma cells. So, intercellular spaces are prominent. Pith helps in the storage of
food materials.
Characteristic features of a dicot stem
1.
Cuticles and trichomes (epidermal stem hairs) are present.
2.
Hypodermis is made up of collenchyma cells.
3.
Chloroplast is present.
4.
Presence of a wavy endodermis.
BIOLOGY
Optional Science - 10
275
5.
Presence of eight vascular bundles arranged in the form of a ring.
6.
The vascular bundles are conjoint, collateral and open.
Anatomical differences between monocot stem and dicot stem
Monocot stem
Dicot stem
The vascular bundles are scattered across the Vascular bundles are arranged in the form of
stem without any definite arrangement.
a ring.
Bundle sheath is present.
Bundle cap is present.
Hypodermis is made up of two or three layers Hypodermis is made up of four-five layers of
of compactly arranged sclerenchyma cells.
compactly arranged collenchyma cells.
Phloem parenchyma, Pith and pericycle are Phloem parenchyma, Pith and pericycle are
absent.
present.
Vascular bundles are conjoint, collateral and Vascular bundles are conjoint, collateral and
closed.
open.
Activity
To study the internal structure of a monocot and dicot stem.
Take any two stems: one of a monocot and another of a dicot. Cut fine sections of both the
stems. Put it in a watch glass, wash it and transfer a fine section or the thinnest cut onto
another watch glass and cover it with safranin for 1-2 minutes. Pick up the section, wash
it gently with water and keep on the glass slide. Put one drop of glycerine. Cover it with
a coverslip and observe it under a microscope. Draw a diagramand explain about the
observed structure.
Root
A root is a vascular part of plant present normally underground. Some plants (like money
plant, maize,etc.) have aerial roots. Root's function is to anchorage the plant and absorb water
and dissolved minerals from the soil and conduct it towards stem. It also acts as a reserve
material of food. There are two types of roots: Tap root and adventitious root.
Internal structure of a monocot root
A transverse section of a monocot root shows the
following structure:
1. Epiblema
2. Cortex
3. Endodermis
4. Pericycle
5. Vascular bundles
6. Conjunctive tissue
Root hair
Epiblema
(Rhizodermis)
Cortex
7. Pith
1.
Epiblema: It is the outermost covering of the root
without cuticle. It is formed by a single layer of
compactly arranged barrel shaped parenchyma
cells. These cells absorb water. Some of the
epiblema cells develop long unicellular hair like
projections called root hairs.
276
Optional Science - 10
BIOLOGY
Pith
Passage
cell
Pericycle
Epidermis
Phloem
Protoxylem
Casparing
Thickening
fig: Internal structure of monocot root
2.
Cortex: The cortex is made up of several layers of loosely arranged parenchyma cells.
Therefore, intercellular spaces are prominent. It is a major component of the ground
tissue and helps in storage of water.
3.
Endodermis: The endodermis is made up of compactly arranged barrel shaped cells.
It is the innermost layer of the cortex. Some cells of the endodermis are thin walled.
These cells allow water to pass into the xylem vessels. These cells are known as passage
cells. In the wall of the remaining cells of the endodermis, a waxy substance called
suberin gets deposited and makes it thick. These depositions are known as casparian
thickenings. It creates and maintains a physical force called root pressure.
4.
Pericycle: The pericycle is formed by a single layer of parenchyma cells. It gives lateral
roots.
5.
Vascular bundles: Vascular bundles are radially arranged in the form of ring. The
xylem and phloem are numerous in number. They lie on different radii alternating with
each other.
6.
Conjunctive tissue: Conjunctive tissue is formed by loosely arranged parenchyma cells.
These cells are found between the vascular bundles. Conjunctive tissue stores water.
7.
Pith: The pith is the central portion of the root. It is made up of loosely arranged
parenchyma cells. Therefore, intercellular spaces are present. It is well developed in a
monocot root. It stores food.
Characteristic features of monocot root
1.
2.
3.
4.
Presence of unicellular root hairs.
Presence of passage cells.
Presence of casparian thickenings in the endodermis.
Presence of conjunctive tissue.
5.
Presence of radial vascular bundles.
Internal structure of a dicot root
A transverse section of a dicot root shows the following structures:
1.
2.
1. Epiblema
2. Cortex
Root hair
Epiblema
(Rhizodermis)
3. Endodermis
4. Pericycle
5. Vascular bundles
6. Conjuctive tissue
Cortex
7. Pith
Epiblema: The epiblema is formed by a single layer of
Epidermis
Phloem
barrel shaped parenchyma cells. These cells are thin
Pericycle
Protoxylem
walled and compactly arranged. Therefore, there are
Conjnctive tissue
Metaxylem
no intercellular spaces. They absorb water. Some of
Casparian strip
Passage cell
the epiblema cells develop long unicellular hair like
projections called root hairs. It gives protection to the
fig: Internal structure of dicot root
roots and also helps in absorption of water and minerals from soil. Stomata and cuticle
are absent.
Cortex: The cortex is made up of several layers of loosely arranged parenchyma cells.
Therefore, intercellular spaces are prominent. It is a major component of the ground
tissue meant for storing starch. The cells of the cortex allow free movement of water into
the xylem vessels.
BIOLOGY
Optional Science - 10
277
3.
Endodermis: The endodermis is made up of compactly arranged barrel shaped cells.
It is the innermost layer of the cortex. Some cells of the endodermis are thin walled.
These cells allow water to pass into the xylem vessels. These cells are known as passage
cells. In the wall of the remaining cells of the endodermis, a waxy substance called
suberin gets deposited and makes it thick. These depositions are known as casparian
thickenings. It creates and maintains a physical force called root pressure.
4.
Pericycle: The pericycle is formed by a single layer of parenchyma cells. Intercellular
space is absent.
5.
Vascular Bundles: Vascular bundles are radial in arrangement. There are four bundles
each of xylem and phloem. They lie on different radii alternating with each other.
6.
Conjunctive tissue: Conjuctive tissue is formed by loosely arranged parenchyma cells.
These cells are found between the vascular bundles. Conjunctive tissue stores water.
7.
Pith: The pith is the central portion of the root. It is made up of loosely arranged
parenchyma cells. Therefore, intercellular spaces are present. It is reduced in dicot roots
or even absent in older roots. It helps in storage of food.
Characteristic features of a dicot root
1.
2.
3.
4.
5.
6.
7.
Presence of unicellular root hairs.
Presence of passage cells.
Absence of hypodermis
Presence of casparian thickenings in the endodermis.
Presence of conjunctive tissue.
Presence of radial vascular bundles.
Absence of pith in older dicot plant.
Anatomical differences between monocot root and dicot root
Monocot root
Xylem vessels are oval or rounded..
Pith is large and well developed.
Dicot root
Xylem vessels are polygonal or angular in
shape.
Pith is absent or insignificant.
Conjunctive tissue does not form vascular Conjunctive tissue forms vascular cambium.
cambium.
Secondary growth does not occur.
Secondary growth occurs.
Xylem and phloem are numerous in number. Xylem and phloem are limited in number.
Activity
To study the internal structure of monocot and dicot roots.
Take any two roots, one of a monocot and another of a dicot. Cut fine sections of both
the roots. Put themon a watch glass, wash and transfer a fine section or the thinnest cut
onto another watch glass and cover it with safranin for 1-2 minutes. Pick up the section,
wash it gently with water and keep on a glass slide. Put one drop of glycerine. Cover it
with a coverslip and observe under a microscope. Draw a diagramand explain about the
observed structure.
·o
278
······························································································································
Optional Science - 10
BIOLOGY
Cell Division
Life of an organism begins from a single cell (zygote formed
Sperm.-Egg
by fusion of gametes in sexual reproduction). There is
a continuous process of division in cells which gives a
structure to the body of multicellular organism. In a living
organism, the growth and multiplication of cells are the
basic necessities for its proper growth. The process of cell
division is similar in all living organisms. The cell which is
undergoing cell division is called mother cell and the new
cells formed from cell division are called daughter cells. Cell
division is the process by which a mother cell divides into
two or more daughter cells. Cell division was first studied
by Prevost and Dumas (1824 AD) when they described cleavage in fertilized egg of Frog.
Cell Cycle
The cell cycle is the sequence of changes that takes place in the cells during cell growth and
cell division. In cell division, a mother cell divides into daughter cells. The daugher cell grows
into a mature cell and prepares for cell division. So, every cell is derived from the preexisting
cell. All the changes that occur between two consecutive cell division come under cell cycle.
The division of nucleated cells completes with cytokinesis (division of cytoplasm)followed
after Karyokinesisis (nuclear division). Sometimes cytokinesis does not follow the karyokinesis,
as a result multinucleated cells are formed. In eukaryotes, the cell cycle can be divided into
three phases – Interphase, M phase (mitotic or meiotic phase) and cytokinesis.
fig: cell cycle
Phases of Cell Cycle
1.
Interphase
Interphase is the stage during which a cell prepares, grows and accumulates nutrients
needed for cell division. It is the stage between the end of one cell division to the
beginning of another cell division. The interphase is the longest phase of a cell cycle.
This stage is also known as resting stage as cell division does not take place in this phase.
Though it is called a resting stage, cell is metabolically active in interphase. This phase
is the preparatory phase. The cells grow, develop and carry out their metabolic function.
There are three distinct phases in the interphase of the cell cycle - G₁ phase, S phase and
G₂ phase.
BIOLOGY
Optional Science - 10
279
G₁ phase (Gap one/first growth phase): This is the first phase in the interphase. Here
G indicates gap. This phase is also called the growth phase. Cells carry out normal
metabolic activities. The changes that occur in the cell in this sub-phase are:
i. Carbohydrates, lipids and proteins are synthesized. RNAs are formed.
ii. The cell matures and increases in size due to high rate of biosynthesis.
Sphase (Synthesis): The S or synthesis phase follows the G₁ phase. The changes that
occur in the cell in this sub-phase are:
i. The genetic material of the cell (DNA) is copied or replicated.
ii. The synthesis of the vast majority of histones occurs during the S-phase.
G₂ phase (Gap two/second growth phase): The G₂ or second Growth Phase occurs after
the S phase. The changes that occur in the cell in this sub-phase are:
i. Cell grows rapidly during this sub-phase. The cell makes all the structures needed to
divide.
ii. Protein synthesis during this sub-phase prepares for the energy required in M-phase.
Fact with reason
Interphase is also called resting phase,why?
In interphase, the division of nucleus and cytosol does not occur. Any of the cellular structure
does not divide, the cell just prepares for division. So, interphase is called resting phase.
2.
M-phase
The M phase consists of nuclear division (karyokinesis). The M-phase copletes in four
distinct stages, namely prophase, metaphase, anaphase and telophase. At the end of
M-phase the nucleus of a cell divides itself into two or four distinct nuclei, known as
'daughter nuclei'. This process of division of the mother cell nucleus into daughter nuclei
is called karyokinesis.
3.
Cytokinesis:
Cytokinesis is the division of cytoplasm into two separate cells which occurs concurrently
with nuclear division in M-phase of cell cycle. It is the final phase in cell cycle followed
after karyokinesis, where there is division of cytoplasm to form daughter cells. The
process of cytokinesis differs in plant and animal cells. Cytokinesis occurs by two
methods: cell plate formation and constriction (furrowing/cleavaging) methods.
Cytokinesis in animal cells
In an animal cell, cytokinesis takes places by contraction/furrowing/cleavaging methods.
In this process, a peripheral constriction appears in the cytoplasm at the equator. Slowly,
it continues and deepens towards the center and constricts the cytoplasm to divide it into
two equal halves
Cytokinesis in plant cells
In plant cells, cytokinesis takes place by cell plate formation method. In this process, the
granular bodies produced by the golgi complex or endoplasmic reticulum are arranged
in the equatorial region, form a cell plate and divide the cytoplasm into two equal halves.
0
280
Optional Science - 10
BIOLOGY
Memory Plus
The period of the cell cycle varies in different cells. It is 20 minutes in a bacterial cell and 8-10
minutes in an epithelial cell.
The cycle of cell division is a vital process by which a fertilized egg that is single-celled develops
into a mature organism. It is the process by which the skin, hair, blood cells and some internal
organs are renewed.
Types of Cell Division
There are two types of cell division:
a)
b)
Direct cell division: amitosis.
Indirect cell division: mitosis (equational cell division) and meiosis (reductional cell
division)
Amitosis
Amitosis is a simple type of cell division. It is a means of asexual reproduction. It occurs in
unicellular organisms like bacteria, amoeba, etc. In this cell division, the nucleus elongates
and then takes a dumb-bell shaped appearance. The depression and constriction in the nucleus
divides the nucleus into two nuclei. Therefore, it is also called direct nuclear division. The
division of the nucleus is followed by the constriction of the cytoplasm, which divides the cell
into two equal or approximately similar halves.
In amitosis, the two daughter cells do not receive
equal amount of nuclear and cytoplasmic materials.
They do not resemble with their parents as well as
with each other. Amitosis occurs during binary fission
in bacteria, cyanobacteria and some protozoans like
amoeba, paramecium, euglena, etc. It is frequently
found in the fast growing cells of cancer.
Constriction
Nucleus
Parent cell
Parent cell
dividing
Daughter cells
fig: Stages in amitosis
Fact with reason
The two daughter cells do not look identical in amitosis,why?
During the division of cells in amitosis the chromatin fibres do not replicate as in mitosis. The
genetic material does not get equally distributed when the nucleus divides into two nuclei. Thus the
two daughter cells do not look identical.
Amitosis is called direct cell division, why?
Amitosis takes place by simple cleavage of the nucleus and division of the cytoplasm
without spindle formation or appearance of chromosomes. So amitosis is called direct cell
division.
Mitosis
Mitosis is the division of a mother cell into two daughter cells with equal number of
chromosomes to that in mother cell. These daughter cells are genetically identical to each other
and to the parent cell. It is also called equational cell division. The term mitosis was coined by
Walter Flemming in 1882 AD. Mitisis occurs in somatic cells. So, mitosis is also called somatic
cell division. The word ‘somatic’ is derived from the Greek word ‘soma’ which means body.
BIOLOGY
Optional Science - 10
281
Hence, all the body cells of an organism that are responsible for growth and development
of the body, except the gametes (sperm or ovum) are called somatic cells. A diploid somatic
cell contains two complete sets of chromosomes. It is denoted by '2n'. For example, a human
somatic cell contains 23 pairs (2n= 2*23=46) of chromosomes. On the other hand, the gamete
with single set of chromosome is called haploid cell. It is denoted by 'n'.
Fact with reason
Mitosis is also called an equational cell division, why?
In mitosis, the chromosomes replicate and get equally distributed into two daughter cells.
The daughter cells have the same number of chromosomes as present in the mother cell.
i.e., number of chromosomes in mother cell(2n) = number of chromosomes in daughter
cell(2n). Therefore, it is also known as equational cell division.
Mitosis is also called somatic cell division, why?
Mitosis takes place in somatic cells (body cells except gametes) for the growth, development
and repair. So, it is also called somatic cell division.
Stages of Mitosis
Mitosis is followed by cytokinesis. This process divides the nuclei, cytoplasm, cellular
organelles and cell membrane into two daughter cells. It is divided into the following three
stages: interphase, karyokinesis, cytokinesis.
Interphase: Interphase is the time during which preparations for mitosis are made by the
cell. Following are the changes that occur in the cell in interphase:
i.
The cell matures and increases in size.
ii.
DNA replicates to form exact two copies of DNA.
iii.
Chromosomes
chromatin.
are
in
the
form
of
Centrosomes
with centrioles
Aster
iv.
RNA and proteins (histone proteins and
spindle proteins) are also synthesized.
v.
Cell replicates its organelles
preparation for mitosis.
in
Chromatin
netweork
Nucleolus
Nuclear
membrane
Karyokinesis:
Cell membrane
fig: Interphase
It is the division of the nucleus into two identical daughter nuclei. The division of the
nucleus takes place in four different phases:
1. Prophase
2.
Metaphase
3.
Anaphase
4.
Telophase
1. Prophase: Following are the changes that occur in the
cell in prophase:
i.
The chromosomes become shorter and more
compact.
282
ii.
Inside the nucleus, the nucleolus starts to
disappear.
iii.
The centrioles begin to move to opposite ends of
fig: Prophase
the cell, and the spindle fibers extend from the centromere.
Optional Science - 10
BIOLOGY
Nucleolus
Centriole
Nuclear
membrane
A pair of
chromatids
Centromere
iv.
At the end of the prophase, the membrane around the nucleus in the cell dissolves
away, releasing the chromosomes.
v.
Each replicated chromosome consists of two identical sister chromatids held
together by a centromere.
2. Metaphase: Following are the changes that occur in the cell in metaphase:
i.
The chromosomes are arranged neatly end-to-end along the center (equator) of
the cell.
ii.
The centrioles are at opposite poles of the cell
with the spindle fibers extending from them.
iii.
iv.
Metaphase
plate
Spindle fibres
The chromosomes start pulling the chromosomes
towards the ends of the cell.
The centromeres of the chromosomes are
arranged along the metaphase plate, also
known as the equatorial plane. This process
of arrangement of all the chromosomes at the
equator is called congression.
Centriole
Centromere
fig: Metaphase
3. Anaphase: Following are the changes that occur in the cell in anaphase:
i.
Centromere splits and two sister chromatids
separate as daughter chromosomes with their
own centomeres.
ii.
There is repulsion between two sister
chromosomes. The sister chromatids are then
pulled apart by the spindle fiber, which pulls one
chromatid to one pole and the other chromatid to
the opposite pole.
iii.
Chromatids move apart
(now called daughter chromosomes)
fig: Anaphase
The daughter chromosomes appear as U, V, L and J during the migration of the
daughter chromosomes.
4. Telophase: This is the last stage of karyokinesis. Following are the changes that occur
in the cell in telophase:
i.
Chromosomes reach at the poles.
ii.
The chromosomes spread and overlap
to form a chromatin network.
iii.
iv.
The spindle fibers disappear, whereas
the nuclear membrane and nucleolus
reappear.
Nucleolus
Centriole
Nuclear
membrane
Constriction in
cell membrane
fig: Telophase
At the end of the telophase, two daughter nuclei are formed, each having an
equal number of chromosomes to the mother cell.
BIOLOGY
Optional Science - 10
0
283
Cytokinesis:
After karyokinesis, cytokinesis takes
place to divide the cytoplasm to form
two identical daughter cells.
Significance of Mitosis
Chromatin Network
fig: two diploid daughter cells formed after cytokinesis
1.
Mitosis division is responsible for the growth and development of a single-celled zygote
into a multicellular organism.
2.
The chromosome number remains the same in the daughter cells produced by this
division. They have the same characters as those of the mother cell. So, mitosis maintains
genetic stability.
3.
Mitosis replaces wounded, old, decaying and dead cells.
4.
It helps unicellular organisms in asexual reproduction.
5.
Artificial vegetative propagation like grafting and the modern method of tissue culture
are possible due to mitosis.
Memory Plus
The cells undergoing mitosis are called mitocytes. In plants, the mitocytes are mostly
meristematic cells. In animals, the mitocytes are stem cells, germinal epithelium and embryonic
cells.
Roughly 5×109 cells are lost from the surface of skin, alimentary canal, etc. daily in our body
which are replaced by the new cells formed by mitosis cell division.
Meiosis
Meiosis is the division of a mother cell into four daughter cells (sex cells or gametes) each
having half number of chromosomes than that in the mother cell. The word ‘meiosis’ was
originated from greek word meioum which means to reduce. It was given by Farmer and
Moore in 1905AD. Whereas this process of cell division was first demonstrated by Van Benden
in 1883AD. The number of chromosomes is reduced by half in meiosis cell division. It is also
called reductional cell division. Meiosis division occurs only in diploid reproduction cells or
germ cells and produces four haploid sex-cells or gametes. A germ cell is any biological cell
that gives rise to the gametes of an organism that reproduces sexually. So, meiosis cell division
is necessary for sexual reproduction in eukaryotic organisms.
Fact with reason
Meiosis is also called reductional cell division, why?
In meiosis, only half number of the chromosomes are distributed from diploid mother cell to
the daughter cells (sperm and ovum). i.e.,
number of chromosomes in daughter cell(n) = ¹/2 number of chromosomes in mother
cell(2n). Therefore, meiosis is also known as reductional cell division.
Stages of Meiosis
Meiotic division includes two complete divisions (meiosis I and meiosis II). It can be studied
in the following three stages: Interphase, karyokinesis and cytokinesis.
284
Optional Science - 10
BIOLOGY
Interphase: Before entering meiosis I, a cell first goes through the Interphase. As in mitosis,
the cell grows during the G1 phase (Growth phase), copies all of its chromosomes during
the S phase, and prepares for division during the G2 phase. The replicating process in
S-phase is longer than that occurs in mitosis.
Karyokinesis: In meiotic cell division, the nucleus divides twice. In meiosis I, one diploid
mother nucleus is divided into two haploid daughter nuclei. In meiosis II, each haploid
nucleus formed as a result of meiosis I divides into two haploid daughter nuclei. As a
result, four haploid nuclei are formed from one diploid nucleus at the end of meiosis.
Meiosis I: In meiosis I there are four stages:
1. Prophase I
2. Metaphase I 3. Anaphase I
4. Telophase I.
1. Prophase I:
It is a very complex and long phase in meiosis I. Prophase I is further divided into 5 subphases: Leptotene, Zygotene, Pachytene, Diplotene and Diakinesis.
a. Leptotene (Gk: leptonema- thin threads): Following changes occur in the cell in
leptotene:
i.
In this stage, the chromosomes condense into thin, elongated, single stranded
thread like structure.
ii.
Size of the nucleus increases.
iii.
Centrosome splits into two centrioles, and each centriole starts to move towards
its respective poles.
iv.
Nuclear membrane and nucleolus remain intact.
lnterphase
leptotene
Synapsis of homologous
chromosomes
Nucleolus
(Disappearing)
Pachytene
Zygotene
Chiasmata
Crossing
over in
Pachytene
Diplotene
Astral rays
Diakinesis
fig: Stages in Prophase I
b. Zygotene (Gk: zygonema- paired threads): Following changes occur in the cell in
zygotene:
i.
The homologous chromosomes line up with each other to form a pair called
bivalent. These paired chromosomes are called bivalent chromosomes. This
process of pairing up of homologous chromosomes to form a bivalent is called
synapsis.
BIOLOGY
Optional Science - 10
0
285
ii.
Shortening and thickening of chromosomes continues.
c. Pachytene (Gk: pachynema- thick threads): Following changes occur in the cell in
pachytene:
i.
In this stage, each chromosome splits longitudinally into two sister chromatids.
The two bivalent chromosomes split to form 4 arms. The structure so formed is
called a tetrad.
ii.
Non-sister chromatids overlap or coil with each other. During this process sister
chromatids remain attached at some points. These points of contact between two
non-sister chromatids are called the chiasmata.
iii.
Crossing-over begins in this stage. There is an exchange of genetic material
between the non-sister chromatids, and this results in a recombination of
information. The process of exchange of genetic material from the chiasmata in
between two non-sister chromatids of homologous pair is called crossing over.
Memory Plus
Chromosomal cross-over is a significant source of genetic variation. As the DNA
created is of new combinations.
d. Diplotene (Gk: diplonema- two threads): Following changes occur in the cell in
Diplotene
i.
Crossing-over takes place.
ii.
The bivalent homologous chromosomes remain tightly bound at the region of the
chiasmata, where crossing over occurred.
iii.
Nuclear membrane and nucleolus start to dissolve.
iv.
Non-sister chromatids start to separate from each other except at the chiasmata.
e. Diakinesis (Gk: Diakinesis- moving through): Following changes occur in the cell in
diakinesis:
i.
During the diakinesis stage, the chromosomes condense further.
ii.
This stage is the first part of meiosis, where the four arms of the tetrad are visible.
iii.
Nuclear membrane and nucleolus dissolve completely. Spindle fibers start to
appear.
iv.
Chiasmata move towards the terminal end of the chromosome. This process of
movement of chiasmata towards the end of the chromosome and disappear is
called terminalization.
Metaphase I: Following changes take place in this phase:
i.
The homologous pairs of chromatids are arranged on equatorial region known as
the metaphase plate in such a way that the two members of a pair lie on opposite
sides of the equatorial plane.
286
ii.
The centromeres are directed towards the poles, and the arms of chromosomes
face the equatorial plate called co-orientation.
iii.
The chromosomes are attached to the spindle fibers by their centromeres.
Optional Science - 10
BIOLOGY
iv.
As centromere does not split in this phase, the number of chromosomes moving
towards the opposite pole is reduced into half of that in the mother cell. As a
result a haploid nucleus is formed in each pole.
Anaphase I: Following changes take place in this phase:
i.
Homologous chromosomes are pulled towards the opposite poles, which results
in the formation of two haploid sets. This process of separation of homologous
chromosomes is called disjunction.
ii.
This process of separation of homologous chromosomes is called disjunction.
iii.
The centromere does not split. Each chromosome contains a pair of sister
chromatids. These chromosomes are called dyads.
iv.
As centromere does not split in this phase, the number of chromosomes moving
towards the opposite pole is reduced into half of that in the mother cell. As a
result a haploid nucleus is formed in each pole..
Telophase I: Following changes take place in this phase:
i.
The daughter cells now have half the number of chromosomes. The chromosomes
consist of a pair of chromatids.
ii.
The network of spindle fibers disappears. Nuclear membrane and nucleolus
appear.
iii.
The chromosomes uncoil and form chromatin threads.
iv.
At the end of telophase-I, two haploid nuclei are formed. In some cases, telophase-I
may be absent.
Cytokinesis-I:
Cytokinesis takes place through cell plate formation in the plant cell and by the furrowing
method in the animal cell. This completes the formation of two haploid daughter cells.
Interkinesis:
i.
It is a period of rest between meiosis I and meiosis II.
ii.
There is no DNA replication, i.e., S-phase is absent.
ANAPHASEIiii.
I
INTERPHASE
PROPHASE I
METAPHASEI
iv.
Centrosomes
(with centriole
pairs)
Chiasmata
Spindle
Microtubule
attached to
kinetochore
Meta phase
plate
Sister chromatids
remain attached
+
Nuclear
envelope
Chromosomes
duplicate
Tetrad
Sister
chromalids
Homologous
chromosomes
pair and exchange
segments
Centromere
(with kinelochore)
Tetrads line up
Pairs of homologous
chromosomes
split up
fig: Stages in meiosis I
BIOLOGY
Optional Science - 10
287
Meiosis II (equational cell division): It is the second part of the meiosis cell division.
Meiosis II is similar to mitosis. But meiosis II occurs in haploid cells instead of diploid
cells as that in mitosis. It results into four haploid cells from two haploid cells produced
in meiosis I.
Fact with reason
Meiosis II phase is also called meiotic mitosis,why?
All the changes that occur in meiosis II phase are similar to that which occurs in mitosis. So,
this phase is also called meiotic mitosis or homotypic division.
In meiosis II, there are four stages:
1. Prophase II
2. Metaphase II telophase &
cytokinesis
prophase II
3. Anaphase II
metaphase II
anaphase II
4. Telophase II.
telophase II
Cleavage
furrow
Two haploid cells
form; chromosomes
are still double
During another round.of cell division, the sister chromatids finally
separate; four haploid daughter cells result, containing single
chromosomes
fig: Stages in meiosis II
Prophase II : Following changes take place in this phase:
i.
During this stage, the nucleoli and the nuclear envelope disappear.
ii.
Chromatids become short and thick.
iii.
The centrioles move to the polar region.
iv.
The spindle fibers appear for the second meiotic division.
Metaphase II: Following changes take place in this phase:
i.
During this stage, the centromeres attach to the spindle fibers at each pole.
ii.
Nuclear membrane and nucleolus completely disappear.
iii.
Dyad chromosomes arrange themselves in an equatorial plane.
Anaphase II: Following changes take place in this phase:
i.
In this stage the centromeres are cleaved, pulling apart the sister chromatids.
ii.
The daughter chromosomes move towards the opposing poles.
Telophase II: Following changes take place in this phase:
i.
In this phase there is uncoiling and lengthening of the chromosomes.
288
ii.
The spindle fibers disappear.
iii.
Nucleolus and nuclear envelope reappear.
Optional Science - 10
BIOLOGY
Cytokinesis II: Cytokinesis II takes place by cell plate formation in the plant cell and by
furrowing in the animal cell. As a result, four haploid daughter cells are formed at the
end of cytokinesis-II from a single diploid nucleus.
Memory Plus
The cells undergoing meiosis are known as meiocytes. In animals, the meiocytes are the primary
spermatocytes and primary oocytes, while in plants, these are represented by sporocytes.
Significance of meiosis
1.
Meiosis produces haploid cells (i.e. male and
female gametes or spores). So, it is responsible
for sexual reproduction in organisms.
2.
Reduction in chromosome number. Each gamete
has only half the number of chromosomes of the
parent cell.
3.
Meiosis reduces the number of chromosomes
into half during gamete formation. When male
gamete and female gamete fuse then the number
of chromosomes in zygote remains fixed to the
parental organism. Thus, meosis maintains
genetic stability in the offspring by keeping fixed
number of chromosomes in the offspring. In
other words, meiosis maintenance the number
of chromosome fixed in somatic cells.
4.
Meiosis causes genetic variation. New
individuals do not resemble their parents closely.
0 Haploid (n)
Haploid gametes (n = 23)
O Diploid (2n)
@
Ovum (n)
&=~
I Fertlllzallonl
Testis
~
~
Mitosis and
Diploid
zygote
(2n=46)
development
Multicellular diploid
adults (2n = 46)
fig: significance of meiosis in sexual reproduction
Activity
Study the permanent slides showing different stages of mitosis and meiosis. Observe
through microscope and copy the diagrams observed on the permanent slide. Also
comment on different stages of mitosis and meiosis.
Difference between Mitosis and Meiosis
Mitosis
Mitosis occurs in somatic cells.
It produces two daughter cells.
Meiosis
Meiosis occurs in reproduction cells.
It produces four daughter cells.
It completes in one division.
It completes in two divisions.
In mitosis cell division, genetic constitution In meiosis cell division, genetic constitution
remains same in the daughter cell.
is different in the daughter cells
It takes place during growth, repair, It takes place during formation of gametes
regeneration and development
BIOLOGY
Optional Science - 10
0
289
Answer writing skill
1.
Define cell biology.
Cell biology is defined as a branch of life science that deals with the study of the cell
structure, its function and its chemistry.
2.
Define bone.
Bone is defined as a hard connective tissue made up of living cells called osteocytes.
3.
What is a cell cycle?
A cell cycle is the sequence of changes that take place in the cells during cell division.
4.
Mitosis is called equational cell division. Why?
Mitosis is the division of the mother cell into two daughter cells. These daughter cells
are genetically identical to each other and to the parent cell. Both the daughter cells
contain the same number of chromosomes as the parent nucleus. Therefore, it is also
known as equational cell division.
5.
Write short notes on cuboidal epithelial tissue.
Cuboidal tissue
Cuboidal tissue contains cubical cells. It forms the lining of ducts of the kidney, salivary
gland, pancrease, testis and ovary. It helps in secretion, absorption and excretion. There
are two types of cuboidal epithelial tissue:
6.
a.
Ciliated cuboidal: The cuboidal cell having cilia on the free surface is called a
ciliated cuboidal cell. The cilia help in conducting mucus and other substances.
They are located on the ducts of nephrons.
b.
Brush bordered cuboidal: The cuboidal cell having microvilli on the free surface
is called a brush bordered cuboidal cell.
What are the main identifying characteristics of a dicot stem?
The main identifying characteristics of a dicot stem are as follows:
7.
1.
Cuticles and trichomes are present.
2.
Hypodermis is made of up collenchyma cells.
3.
Chloroplast is present.
4.
Presence of a wavy endodermis.
5.
Presence of eight vascular bundles arranged in the form of a ring.
6.
The vascular bundles are conjoint, collateral and open.
Describe anaphase in mitosis.
In anaphase of mitosis, the following changes occur:
1.
0
290
Each chromosome is divided into two sister chromatids as separate daughter
chromosomes with their own centomeres.
Optional Science - 10
BIOLOGY
8.
2.
The sister chromatids are then pulled apart by the spindle fiber, which pulls one
chromatid towards one pole and the other chromatid towards the opposite pole.
3.
The daughter chromosomes appear as U, V, L, and J during the migration of the
daughter chromosomes.
What is a compound epithelium? What are its types? Give two functions of it.
A compound epithelial tissue is a type of epithelial tissue which is made up of several
layers of epithelial tissue.
Compound epithelial tissues are of following types:
1.
Stratified squamous epithelium: It is made up of several layers of cells. The upper
layer is made up of squamous cells. The lower layer is made up of germinative
columnar or cuboidal cells. The stratified squamous epithelium is of two types:
a.
Keratinized epithelium: This tissue contains protein called keratin in its
upper layer. This layer is hard. It makes the layer water-proof. It is present
inthe hair, claws and nails.
b.
Non-keratinized epithelium: The upper layer of this tissue contains living
cells. Due to the absence of keratin, this layer becomes wet. It is present in the
buccal cavity, pharynx, oesophagus and vagina.
2.
Stratified cuboidal epithelium: The upper layer of this tissue is made up of
cuboidal cells. The lower layer is made up of either germinative columnar or
squamous cells. It is found in the lining of ducts of sweat glands, salivary glands,
conjunctiva of the eyes, etc.
3.
Stratified columnar epithelium: The upper layer of this tissue is made up of
columnar cells. The lower layer is made up of germinative cuboidalcells. It is
found in the liningof vasa deferntia, trachea, bronchi, etc.
4.
Transitional epithelium: This tissue is made up of several layers of cells. The cells
in the upper layer are dome shaped. The cells in the middle layer are club shaped.
The cells in the basal layer are cuboidal in shape. This tissue has the ability to
stretch and relax. It helps in the expansion of organs. It is found in the urinary
bladder and ureter.
BIOLOGY
Optional Science - 10
291
Exercise
Section "A"
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
What is a tissue?
Define connective tissue.
What is cartilage?
What is a nerve cell called?
Give an example of neuroglia.
Define epithelial tissue.
What do you understand by glandular epithelium?
What is compound epithelium tissue?
What is keratinized epithelium?
What is cell division?
What do you mean by cytokinesis and karyokinesis?
Define amitosis.
What is mitosis cell division?
What is meiosis cell division?
What is crossing over?
What is a homologous chromosome?
Section "B"
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
What are the types of animal tissues?
What are the types of connective tissue?
Give two differences between white fibrous and yellow fibrous tissue.
Distinguish between striated and unstriated muscle.
Describe in brief cardiac muscle tissue.
What are the types of epithelial tissue?
Name any two organs in our body which contain ciliated epithelium.
Name any two organs in our body which contain columnar epithelium.
Write the anatomical differences between a dicot root and monocot root.
Write the anatomical differences between a dicot stem and monocot stem.
Give the names of the different stages of cell division.
Name the phases of the cell cycle.
What are the changes that occur during G1, S and G2 phase.
292
Optional Science - 10
BIOLOGY
14.
15.
16.
17.
18.
19
20.
21.
22.
23.
24.
25.
Give reason
a. Meiosis is called a reductional cell division
b. Mitosis is called an equational cell division
c. Meiosis brings variation in offsprings
d. Cell division is a necessary phenomenon
What are the stages of mitosis?
What are the stages of meiosis cell division?
Mention the differences between metaphase and anaphase.
Mention the differences between anaphase in mitosis and anaphase in meiosis.
Write differences between cytokinesis in plant cell and cytokinesis in animal cell.
Write differences between haploid cell and diploid cell
Write the differences between Prophase I and Prophase II.
Give the differences between mitosis and meiosis.
Write down the sub-phases of Prophase I.
Give difference between mitosis and meiosis cell division.
What is the basic difference between mitosis in plant cell and that in animal cell.
Section "C"
1.
2.
3.
4.
5.
6.
7.
8.
9.
Write any three function of connective tissue.
Write the function of blood.
State the function of lymph.
What is the function of epithelial tissue?
Write functions of muscular tissue.
Write functions of nervous tissue.
Explain the significance of mitosis.
Explain the significance of meiosis cell division
Meiosis and mitosis both maintain the genetic stability. Explain how do they maintain
genetic stability.
Section "D"
1.
2.
3.
4.
5.
6.
7.
8.
10.
11.
12.
Describe in brief the internal structure of a dicot root.
Describe in brief the internal structure of a monocot root.
Describe in brief the internal structure of a dicot stem.
Describe in brief the internal structure of a monocot stem.
Draw a sketch of the transverse section of a monocot stem.
Draw a sketch of the transverse section of a monocot root.
Draw a sketch of the transverse section of a dicot stem.
Draw a sketch of the transverse section of a dicot root.
Describe the process of mitosis.
Describe the types of epithelial tissue.
What are the types of connective tissue? Explain.
BIOLOGY
Optional Science - 10
0
293
13.
14.
15.
16.
17.
18.
19.
20.
Give a short account about nervous tissue and muscular tissue.
Draw labelled diagrams to show metaphase and anaphase of mitosis.
Describe the somatic cell division and mention its significance.
Explain with diagram about the prophase-I.
Give a detailed account of meiotic I cell division.
Describe the process of meiotic II cell division?
Describe the changes that occur in the nucleus during anaphase of mitosis. How is it
different from the anaphase-I of meiosis? Explain along with a diagram.
Complete the following table.
Animal tissue
Areolar tissue
Adipose
Squamous epithelial
cuboidal epithelial
Columnar
Glandular columnar epithelial
Transitional epithelial
Function
Occurrence
Multiple choice questions
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
The science that deals with the study of cell structure, its function and its chemistry is
a. Morphology
b. Cytology
c. Physiology
d. Biology
Study of tissue is called
a. Tissue culture
b. Cell biology
c. Histology
d. Cytology
Blood is an example of
a. Loose connective tissue
b. Dense connective tissue
c. Fluid connective tissue
d. Skeletal connective tissue
Which muscle tissue works continuously without fatigue?
a. Skeletal muscle tissue
b. Smooth muscle tissue
c. Cardiac muscle tissue
d. Nervous tissue
Which tissue forms the lining of the coelom, buccal cavity, blood vessels and kidney?
a. Epithelial tissue
b. Connective tissue
c. Nervous tissue
d. Skeletal tissue
Multicellular hair is absent in
a. Monocot stem
b. Dicot stem
c. Monocot root
d. Dicot root
In which phase does the genetic material of the cell (DNA) get replicated?
a. G0 phase
b. G1 phase
c. S phase
d. G2 phase
Binary fission is an example of
a. Mitosis
b. Meiosis
c. Amitosis
d. All of the above
Equational cell division is
a. Mitosis
b. Meiosis
c. Amitosis
d. Cytosis
The points of contact between two non-sister chromatids are called
a. Crossing over
b. Chiasmata
c. Centroiles
d. Synapsis
qqq
0
294
Optional Science - 10
BIOLOGY
UNIT
15
Life and Life
Processes
Antonie van Leeuwenhoek (1632-1723AD)
He was born in Holland. He was the first to observe the bacteria and protozoa, and proved
that the doctrine of spontaneous generation was wrong on the basis of his research on lower
animals. He was the first acknowledged microscopist and microbiologist because of his
microscopic discovery of microorganisms (animalcule).
Syllabus issued by CDC
Learning objectives:
At the end of this unit, the students will be able to:
• describe different physiologies present in a
mouse like the digestive system, respiratory
system and urogenital system.
Atomic mass, molecular mass and
•
describe the structure and life cycle of a
mole concept
flowering plant (rice).
Quantum numbers
•
describe different endocrine glands, their
Concentration (Normality, molarity,
secretion, functions and their respective
gram per litre and percentage)
effects.
Theory
Practical
10
3
Key terms and terminologies of the unit
Life processes: The basic essential activities performed by an organism to keep it alive and
functioning are called life processes.
Digestive system: The digestive system is a long tract found inside the animal, start from
the mouth and ends with the anus, and helps in digestion.
Digestion: The process of enzymatic breakdown of macromolecules in food materials into
the simplest molecules required for maintaining cellular function is called digestion.
Alimentary canal: The alimentary canal is a pathway by which food enters the body and
solid wastes are thrown out. It is a tube running from the mouth to the anus.
Viscera: The internal organs of digestive system in the main cavities of the body are called
viscera.
BIOLOGY
Optional Science - 10
295
Peristalsis: The involuntary constriction and relaxation of the muscles of the intestine or
another canal, creating wavelike movements that push the contents of the canal forward.
Respiratory system: The respiratory system is the set of organs that helps to inhale oxygen
(for oxidation of food) and exhale carbon dioxide.
Exocrine glands - The glands that secrete enzymes and juices and pour this secretion in the
duct (vessel) to an organ are called exocrine glands.
Endocrine glands: The glands that secrete hormones and pour directly into the bloodstream
without passing through ducts are known as endocrine glands.
Hormones: Hormones are the chemical messengers produced by the endocrine system that
activate, inhibit or control the function of a certain organ or a group of organs.
Endocrine system: The endocrine system is a chemical messenger system of an organism
consisting of hormones, the group of glands that secrete those hormones directly into blood to
regulate the function of distant target organs.
Endocrinology: The branch of science that deals with the study of the structure, secretion and
functions of different endocrine glands is called Endocrinology.
Introduction
We all have observed in our surrounding that living organisms doing respiration, feeding,
reproducing an individual of their own kind, growing in their dimensions, etc. There are
certain basic vital processes which are essential to perform for an organism to survive. These
processes include nutrition, transportation, metabolism, respiration, reproduction, excretion,
etc. The basic essential activities performed by an organism to keep it alive and functioning
are called life processes. All living things perform life processes. In this unit we will learn
about rat, structure and life cycle of rice and endocrine system in human in this unit.
Rat
A rat is found all over the world and almost everywhere. It is a
fossorial animal living in burrows. It is usually herbivorous in
diet. A rat is a mammal that belongs to the genus Rattus. The
most common rate are the black rat, Rattus rattus, and the brown
rat, Rattus norvegicus. Rats are more closely related with human
beings. They have some similar characteristics to human beings.
Physically, both have similar nervous system, circulatory system,
muscle structure, organs like liver and heart, etc. In this unit, we
will learn about digestive system, respiratory system, urogenital
system in rat.
Kingdom:
Animalia
Phylum:
Chordata
Subphylum: Vertebrata
Class:
Mammalia
Order:
Rodentia
Family:
Muridae
Genus:
Rattus
Fact with reason
Why are rats widely used as a model in medical testing by researchers?
Rats are more closely related with human beings. Their genetic, biological and behavior
characteristics closely resemble those of humans. Many symptoms of human conditions can
be replicated in rats. So they are widely used as a model in medical testing by researchers.
0
296
Optional Science - 10
BIOLOGY
External features of Rat
The body of a rat is elongated and covered with thick fur with stiff hairs. The body of a rat can
be divided into four distinct regions: head, neck, trunk and tail.
The head is elongated tapering at the terminal end. It bears two bulging eyes, two nostrils,
mouth, external ears (pinnae) and vibrissae projecting from the side of the mouth. The neck
connects the head to the trunk. The trunk is the
External nares
Vibrissae
largest part of the body. It is divided into the thorax
Upper
incisor
and abdomen. In a female rat, there are six pairs of
External auditory
tooth
meatus
nipples on the ventral side; three pairs in the thoracic
Pinna
Upper arm
region; and three pairs in the abdominal region. A rat
Forearm
Claw
bears two pairs of forelimbs and hind limbs.
The anus is present just below the tail. In the male rat,
there are two scrotal sacs containing the testis and a
penis ventral to the anus. In a female rat, a genital
aperture known as the vulva lies just in front of the
anus. The urethral orifice is present in front of the
vulva. Excretory matter is passed out through the
urethral orifice. The tail is elongated, cylindrical and
tapering. It is slightly longer than the body. The tail
lies above the anus. It is used as a balancing organ.
Prepuce
covering
penis
Thigh
Urethral
orifice
Scrotum
Position of anus
fig: External features of a rat
Digestive system in rat
Animals ingest food in a complex form. A body
system in animals must convert the ingested food into
simple molecules required for maintaining cellular
function. The conversion of the food consumed
to the nutrients required is a multistep process
involving digestion and absorption. Finally, there
is elimination of undigested molecules. This overall
biological process is completed by a group of organs
in digestive system. The digestive system is a long
tract found inside the animal, start from the mouth
and ends with the anus, and helps in digestion. The
process of enzymatic breakdown of macromolecules
in food materials into the simplest molecules required
for maintaining cellular function is called digestion.
trachea
heart
esophagus
aortic arch
lung
liver
bile duct
pyloric
sphincter
duodenum
jejunum
ileum
caecum
diaphragm
stomach
spleen
pancreas
descending
colon
rectum
anus
Alimentary Canal
The digestive system of a rat consists of the alimentary
fig: digestive system of rat
canal and its associated glands. The alimentary canal,
also called the digestive tract, is a pathway by which food enters the body and solid wastes are
thrown out. It is a tube running from the mouth to the anus. The alimentary canal includes the
mouth, pharynx, oesophagus, stomach, small intestine, large intestine and anus. Alimentary
canal of rat is divided into two parts: Mouth and pharynx and Viscera.
BIOLOGY
Optional Science - 10
0
297
1.
Mouth and pharynx
Mouth: The mouth is the large opening at the anterior end of the snout. It is bounded
by two lips. It opens into the buccal cavity, or oral cavity.
Buccal cavity: The buccal cavity contains a long narrow bony jaw with a palate, tongue
and teeth set in a socket. The teeth of the rat are like those of other mammals. The teeth
are heterodont, i.e. they are not all similar to each other. Rats have 16 teeth. A rat’s teeth
consist of incisors (4), canine (0), premolars (0) and molars (12).
Pharynx: It is a small passage between the buccal cavity and the oesophagus. It is the
common chamber for food and air. Pharynx is divided into: Nasopharynx (receives air
from the external nares and is not directly in the oral cavity), Oropharynx (space ventral
to the soft palate) and Laryngopharynx (space posterior to the soft palate and anterior
to the esophagus). From the oral cavity, only food diverges in the laryngopharynx and
directed towards the oesophagus
Oesophagus: It is a long narrow straight tube that passes through the neck and thoracic
region. It opens into the stomach.
2.
Viscera
The internal organs of digestive system in the main cavities of the body are called
viscera. It includes following organs:
Stomach: The food from oesophagus enters to stomach. It is a bean-shaped sac-like
structure on the left side of the abdominal cavity, which is partially covered by the liver.
It acts as a storage organ so that fewer and larger meals can be consumed.
Small intestine: The food from stomach enters to small intestine. It is a long and coiled
slender tube. It is divisible into duodenum, jejunum and ileum. The duodenum is the
first part of the small intestine and forms a U-shaped loop.
Large intestine:The small intestine is followed by the large intestine. It is comparatively
shorter and wider than the small intestine. It is divisible into three parts: caecum, colon
and rectum.
Caecum: It is a thick tube that lies at the junction of the small and large intestine. The
terminal part of the caecum forms the vermiform appendix.
Rectum: It is a straight tube that opens outside through the anus. It temporarily stores
fecal matter before it is thrown out of the body.
Associated digestive glands
Salivary glands: Salivary glands are found in the buccal cavity. There are three pairs of
salivary glands. They are: paratoid gland (below the external ear), submaxillary gland
(near the lower jaw) and sublingual gland (below the tongue). The salivary glands
secrete saliva, which contains the enzyme amylase or ptyalin that helps to digest the
starch in the food. Enzymes in saliva begin the digestion of carbohydrates and mucus
moistens the food and sticks it together to facilitate swallowing.
Gastric glands: Gastric glands are found in the mucosal wall of stomach the stomach
and secrete gastric juice. Gastric juice contains dilute hydrochloric acid (HCl), mucus,
and the enzymes (pepsin, renin and lipase).
0
298
Optional Science - 10
BIOLOGY
Liver: The liver is the largest gland of the body. It lies below the diaphragm. It is a large
reddish brown gland. It contains five lobes. The cells of the liver are called hepatocytes,
which secrete bile. Bile emulsifies fats (breaks them into minute droplets) and makes it
easier to digest them. It also eliminates waste products from the blood. It is carried to
the duodenum by a bile duct. The gall bladder is absent in the rat.
Memory Plus
In humans, the bile is stored and concentrated in gallbladder before it is released
into the small intestine. But rats lack a gall bladder. Therefore, the bile is released
through a duct directly into the small intestine in rats.
Pancreas: The pancreas is situated between the stomach and the duodenum. It secretes
pancreatic juice, which contains digestive enzymes like trypsin, chymotrypsin,
peptidases, amylase, lipase, sucrase, maltase, lactase, etc. These enzymes break down
protein, fat and carbohydrates from the food we eat. Islets of langerhans in the pancreas
secrete certain hormones like insulin, which converts glucose in the liver and muscles.
Intestinal glands: They are present in the mucosal wall of small intestine. They secrete
intestinal juice containing digestive enzyme like erepsin, lipase, nuclease, etc. These
enzymes help in the digestion of food.
Digestion
Digestion is a process by which food is broken down and chemically converted into simple
diffusible form, so that it can be absorbed by the cells of an organism. The absorbed nutrients
are used for energy, growth and cell repair.
In mouth: The mouth is the beginning of the digestion process. As soon as the rat takes the
food through the mouth, it starts chewing. Chewing breaks the food into pieces so that it can
easily be digested. While chewing, saliva mixes with the food and breaks it down into a form
the body can absorb and use. The food travels to the oesophagus through the pharynx. By
means of a series of contractions, called peristalsis, in the oesophagus, the food is delivered to
the stomach.
In stomach: Digestion of proteins begins in stomach. The lining of stomach secrete pepsin
which converts proteins into peptones. Dilute hydrochloric acid is secreted by cells lining
of the stomach to make the environment acidic for activation of pepsin. The muscular walls
of the stomach not only hold the food but also churn the food and mixes it with acids and
enzymes. When the food leaves the stomach, it is in the form of a liquid or paste. The stomach
leads to the duodenum of the small intestine.
In small intestine (duodenum, jejunum and ileum): The actual digestion and the absorption
of the products occur here. The glands present near to it secrete enzymes which help to
breakdown protein and carbohydrate. Liver secretes bile juice and pancreas secretes pancreatic
juice.
In duodenum, the food get mixed with bile which emulsifies the fat and alkaline nature of
bile inactivates the pepsin from the stomach and neutralicex the acid food. Pancreas secrete
enzymes to breakdown fats, carbohydrates and proteins. It continues in the jejunum too.
BIOLOGY
Optional Science - 10
0
299
Then the digested food or nutrients are absorbed in the small intestine (ileum). The walls
of small intestine are made up of columnar epithelial tissues containing villi. These villi
help in the absorption of digested substances and pass them on to the blood capillaries for
distribution. The absorbed nutrients are transported to the rest of the body through the blood
stream or circulatory system.
In caecum: The undigested food (cellulose) and waste materials now come to the rat’s caecum
where fermentation of the plant cellulose takes place due to the bacteria present over there.
Due to this special process to form caecum product rats produce a special feces. They again
ingest this feces to digest for a second time. This behavior is called coprophagy.
Memory Plus
All mammals do not have caecum. Humans have a short caecum provided with the
appendix. The human caecum provides space for digestion, but does not have the
microbes for cellulose fermentation.
In large intestine: After absorption of most of the nutrients and minerals in small intestine
and caecum, the remaining are transported to the large intestine (colon). The water again get
reabsorbed in the large intestine and prepares the solid fecal material for removal from the
body. When the colon becomes full of stool or feces, it empties its contents into the rectum to
begin the process of elimination through the anus.
Differences between the digestive system of a rat and a human:
Digestive system of rat
Digestive system of human
Rats do not have a gall bladder as they rarely In humans, the bile is stored in the gall bladder
take large amounts of fatty food.
before being released into the small intestine
Such stored bile is used to digest fatty foods.
Rats have an enlarged caecum to break Humans have a short caecum provided with
down the cellulose into nutrients present in the appendix. It does not have the microbes
the grains and seeds they feed
for cellulose fermentation.
Activity
With the help of your teacher, dissect a rat carefully. Observe the digestive tract of the rat.
Draw the observed digestive tract of the rat, label it and discuss its digestive system.
Respiratory system in rat
The respiratory system is the set of organs that helps to inhale oxygen (for oxidation of food)
and exhale carbon dioxide. The respiratory system of rat is similar to that of most other
mammals, including humans. It consists of external nares, nasal chambers, internal nares,
pharynx, larynx, trachea, primary bronchi and lungs.
External nares: These are the paired openings that open into the nasal chambers.
Nasal chambers: The nasal chambers are separated from one another by the nasal
septum and from the buccal cavity by the palate.
300
Optional Science - 10
BIOLOGY
Internal nares: These are the posterior openings of the nasal chambers that lead to the
pharynx.
Pharynx: The pharynx is the passage
for both food and air. It is divided
into the nasopharynx above the palate
and the oropharynx behind the buccal
cavity. The edge of the soft palate
acts as a valve to prevent food from
passing into the nasopharynx during
swallowing.
Right caudal lobe
fig: Respiratory system in rat
Larynx or voice box: The pharynx leads to both the larynx and oesophagus. The larynx
consistsof cartilage and has vocal cords. The opening of the pharynx into the larynx, or
voice box, is called the glottis. The glottis is closed when food is swallowed to prevent
the passage of food into the larynx and lower respiratory passages. The vocal cords
help in the production of sound, but it is not well marked in a rat.
Trachea (wind pipe): The trachea is a tube, in the upper portion of the rat’s chest that
connects the pharynx and nasal cavities to the lung. It runs ventral to the oesophagus.
The trachea divides to form two main branches called primary bronchi. Each bronchus
enters a lung. Both the trachea and bronchi have cartilaginous rings embedded in their
walls to prevent the tube from collapsing. As they enter the lungs, each bronchus divides
into secondary branches, or bronchial tubes. Each secondary branch or bronchial tube
divides to form tertiary branches or bronchioles. These are again subdivided into
respiratory bronchioles.
From each respiratory bronchiole, several alveolar ducts arise, leading into subdivisions
called air sacs. The wall of the air sacs is folded to form tiny alveoli. Alveoli are richly
supplied with blood. Exchange of gases takes place in the alveoli.
Lungs: A pair of lungs is present. Each lies one on either side of the rat’s heart in the
thoracic cavity. Left lung of the rat contains only one lobe whereas right lung contains
four lobes. Each lung is composed of numerous branches of bronchiole and each
bronchiole ends with a microscopic unit called alveoli. Alveoli is the unit where the
actual exchange of inhaled oxygen gas and released carbon dioxide gas takes place.
Lungs are lined by two thin membranes, called pleura for their protection. A space
called pleural cavity is present between the two pleura. The pleural cavity is filled with
a pleural fluid. It protects the lungs from mechanical injury and friction during the
contraction and relaxation of lungs. Lungs are protected inside the rib cage.
Respiration in rat
Rats inhale and exhale through their nostrils. Air is brought in through the nasal cavities and
passed into the pharynx, then into the trachea and lungs. When rat is inhaling, the glottis closes
to prevent food particles from entering the pharynx. This prevents the rats from choking on
food particles.
BIOLOGY
Optional Science - 10
0
301
The inhaled air comes to the alveoli travels through the respiratory tract (trachea, bronchi,
bronchioles). In alveoli there is carbon dioxide gas carried by the blood which is produced
from the oxidation of food. Oxygen and carbondioxide gases get exchanged in alveoli. Red
blood cells in the blood absorb oxygen and circulate it to different parts of the rat’s body with
the pumping of heart. Carbon dioxide is exhaled through the same tract.
The trachea connects the pharynx and nasal cavities to the lung. The diaphragm sits just below
the lungs and looks like a sheet of muscle. The diaphragm helps the movement of the lungs
as the rats breathes.
Activity 2
With the help of your teacher, dissect a rat carefully. Observe the respiratory tract of the
rat. Draw the observed respiratory tract of the rat, label it and discuss itsrespiratory system.
Urinogenital system of rat
The urinogenital system of a rat includes the organs concerned with reproduction and urinary
excretion. Although the functions of the organs involved in excretion and reproduction are
unrelated, the organs are morphologically associated and often used as common ducts.
The major structures of the urinary system in a rat are a pair of kidneys, ureters, urinary
bladder and urethra. The principal function of the urinary system is the maintenance of water
and electrolyte homeostasis. The major structures of the reproductive system in the male are
a pair of testes, epididymis, vasa deferens, urethra, and penis. The major structures of the
reproductive system in the female are the ovaries, a pair of fallopian tubes, uterus and vagina.
Excretory organs (urinary system)
Kidneys: The primary organs of the excretory system are the kidneys. These are large
bean shaped structures located toward the back of the abdominal cavity and made up
of millions of nephrons (structural and functional unit of kidney). A rat’s body has a
pair of kidneys, one on the left and one on the right. The right kidney is slightly higher
in position. The kidney consists of an outer cortex and an inner medulla. Bowman’s
Capsule, proximal tubules and distal tubules are located in the cortex. The loop of
Henle and the collecting tubules are located in the medulla. In the center, there is a
spherical structure with a coiled mass of capillaries, called glomerulus.
Kidneys help in the removal of nitrogenous waste products of protein like creatinine,
uric acid, urea, ammonia and controlled amount of water and salts. The function of
kidney occurs in the nephron. At the top of the kidneys, there are small yellowish
glands embedded in the fat called adrenal glands.
Ureters: The ureter is a long tube coming out of each kidney. Ureters carry urine from
the kidney to the urinary bladder.
Urinary bladder: It is a muscular sac-like structure in which two ureters open. The
urinary bladder stores urine temporarily.
Urethra: It is a tubular structure, which extends from the urinary bladder. The urethra
carries urine from the bladder to the urethral orifice. In the male, it carries both urine
and semen.
0
302
Optional Science - 10
BIOLOGY
Reproductive organs of male rat
Testes (singular: testis): Testes are oval shaped organs located in the scrotal sac. The
scrotal sacs are found in the form of pouches lying in front of the anus, between the
hind limbs. Spermatogenesis occurs in epithelial lining within the testes. Testes also
help in the secretion of steroidal hormone like testosterone and progesterone. The
urethra carries the sperm though the penis out of the body.
Epididymis: On the surface of the testis (lying along the inner edge of the testis), there
is a coiled tube called the epididymis. It collects and stores sperm cells.
Vasa deference: The vasa deferens is a straight tube which carries sperm from the
epididymis to the urethra. It lies on the inner side of the testis and opens into the
urethra.
Seminal vesicles: These are the lumpy brown
glands located to the left and right of the
urinary bladder. The gland below the bladder
is the prostate gland. It is partially wrapped
around the penis. The seminal vesicles and the
prostate gland secrete alkaline materials called
seminal fluid (semen).
Penis: It is a long, narrow and cylindrical
copulatory organ. It is covered by a loose
sheath called the prepuce. The penis of the rat
has a bony process called the os-penis.
I
I
)
Accessory sex organs: The accessory sex organs
in male rat are the seminal vesicles, prostate
and coagulating gland.
Uterine Hom
Urinary Bladde
fig: Genital organ of the female rat
Reproductive organs of female rat
Ovaries: Ovaries are small and compact
yellowis pea sized bodies (lumpy glands)
present at the tip of the uterine horns. They
are normally covered by a large amount of fat.
In mature ovaries, ovarian follicles are found.
Ovaries produce ova and female sex hormones.
Fallopian tubes: The fallopian tubes are
narrow coiled and convoluted tubes which
receive ova from the ovary.
)
fig: Genital organ of the female rat.png
Uterus: The uterus is a hollow muscular structure. The uterine horns are fused near the
vagina. Embryonic development takes place in the uterus. The embryo gets attached to
the uterine wall through the placenta.
Vagina: It is a short muscular tube which extends from the uterus and opens outside
as a vaginal opening (vulva). The vagina divides into two uterine horns that extend
toward the kidneys.
Clitoris: It is a small rod like organ lying at the anterior end of the vulva.
BIOLOGY
Optional Science - 10
303
Accessory sex organs: The accessory sex organs in female rat are bulbovrethral gland
and prenuptial gland.
Memory Plus
The duplex uterus (two uterine horns), present in rat, has multiple chambers for the
development of multiple embryos. Whereas only one uterus (simplex uterus) is present
in human.
A female rat delivers 6-8 young ones in a litter. The new born are hairless, blind and
deaf. The gestation period is about 22-23 days.
Activity 3
With the help of your teacher, dissect a rat carefully. Observe the urogenital tract of the
rat. Draw the observed uro-gential tract of the rat, label it and discuss its urinary and
reproductive system.
Life cycle of a rice plant (Oryza sativa)
Introduction
The rice plant is an annual grass that produces an edible seed, which is called rice. Rice is
a staple food in the diet of many cultures worldwide. The rice plant comes from the family
Gramineae (Grass family).
The rice plant grows rapidly. The rice plant usually takes 3-6 months from germination to
maturity, depending on the variety and the environment. It is not a water plant, but substantial
amount of water is required for planting. It is commonly grown in flooded fields. Cultivated
species of rice are considered to be semi-aquatic plants.
General information of the plant
Habitat: Semi-aquatic plant, cosmopolitan in distribution. The
rice plants are commonly found in temperate regions and also in
tropical and sub-tropical regions.
Habit: Annual or perennial shrubs cultivated as a crop.
Root: Adventitious, fibrous
Stem: Erect, herbaceous, solid, cylindrical presence of distinct
nodes and internodes, branching from base, the stem is called
culm.
Classification
Kingdom: Plantae
Division: Tracheophyta
Sub-division: Angiosperm
Class: Monocot
Genus: Oryza
Species: sativa
Type: Rice
Leaf: Simple, alternate, exstipulate, sessile, leaf blade long and narrow with the leaf sheath
surrounding the innternode completely, hairy or rough, linear, parallel venation.
Flower:
i.
It is Bracteate. Which means flower has a bract (i.e. a modified leaf growing just below
a flower which protects the flower in the bud condition).
ii.
It is Zygomorphic. Which means flowers can be divided by only a single plane into
two mirror-image halves.
304
Optional Science - 10
BIOLOGY
iii.
The perianth (i.e., the non-reproductive part of the flower
consisting of the calyx and the corolla) has two lodicules
(i.e., small scales below the ovary)
iv.
Androecium (A) has six stamen and Gynoecium (G) has
one carpel.
Floral formula: Br%P2 A 6G(1)
Note:
Br-Bracteate
P- Perianth
%- Zygomorphic
A- Androecium
G- Gynoecium
Floral diagram:
whorl 1- one palea and one lemma
whorl 2- two lodicules
whorl 3- six stamens
Flornl Diag.-a m
whorl 4- one carpel
Fruit: It is caryopsis. Which means ovary wall (pericarp) is completely fused with the seed
coat.
Seed: Endospermic, with a single cotyledon.
Life cycle of a rice plant
~rlowerint
'I J''
H1-------------- ---------1-----------Yept1tlw phase
!
Reproduct ion
phase
Ylfllbt.
I~------------------------------~
fig: Life cycle of rice plant
Rice varieties can be categorized into two groups: the short-duration varieties, which mature
in 105-120 days, and the long-duration varieties, which mature in 150 days. A 120-day variety,
when planted in a tropical environment, remains around 60 days in the vegetative stage, 30
days in the reproductive stage, and 30 days in the ripening stage.
The growth of the rice plant is divided into three stages:
1.
Vegetative stage (germination to panicle initiation)
2.
Reproductive stage (panicle initiation to flowering) and
3.
Ripening stage (flowering to mature grain)
BIOLOGY
Optional Science - 10
0
305
1.
Vegetative Stage
i.
ii.
Germination: The life cycle of rice begins with a seed. The rice
seed consists of the hull and the endosperm. The hull is an outer
protective coat of the embryo, which forms the actual plant.
The endosperm is the starchy part that provides food for the
seed when it begins to grow. When the seed is sown in watery
conditions, such as a flooded rice field, it will sprout. Cultivated
rice is sown in the spring.
fig: Rice seed
Early vegetative stage: As the seed grows, roots will grow down into the soil
beneath the water. The roots anchor and support the plant. It also absorbs nutrients
from the soil. Leaves will also begin to grow toward the surface of the water. In
cultivated rice, the young seedlings are harvested in bunches. These are then
separated into individual plants and are then replanted in the flooded rice fields in
evenly spaced rows to allow the plant to grow to full size. This improves the yield
of the seeds of the plant.
iii. Late vegetative stage: Late vegetative stage is also referred to as the tillering stage.
When the plant is mature and has reached a height of 3 to 4 feet, it will produce a
reproductive stem called a tiller. This usually occurs around 40 days after sowing.
The stem will continue to grow, eventually producing a flower head.
2.
Reproductive stage
The flower head, also known as a spike, will then produce 100 to 150 tiny flowers. Each
flower is small and forms several long, thin stems that radiate upward from the tiller.
These flowers, once pollinated, will then form seeds. This usually takes around 30 days
to complete.
The first sign that the rice plant is getting ready to enter its reproductive phase is a
bulging of the leaf stem that conceals the developing panicle, called the ‘booting’ stage.
Then the tip of the developing panicle emerges from the stem and continues to grow.
Rice is said to be at the ‘heading’ stage when the panicle is fully visible. Flowering
begins a day after heading has completed. As the flowers open they shed their pollen
on each other so that pollination can occur. Flowering can continue for about 7 days.
3.
Ripening stage
During the next 30 days, the rice seeds will eventually ripen, turning golden brown
when fully ripe. The ripening process can be affected by the temperature and change in
climate. A cool, rainy weather can lengthen the process, while warm, sunny conditions
can shorten it. Once completely ripe, the seeds can then be harvested for food.
Memory Plus
When rice is harvested, it is called ‘paddy’. Each paddy grain has many layers with the
outermost layer forming the husk. Each husk protects one half of the paddy. The husk
is composed of silica and cellulose. The next layer is bran. Bran is mainly composed of
fiber, Vitamin B complex, protein and fat, and forms the most nutritious part. The inner
part of the grain is the rice kernel, which is composed of mainly starch.
306
Optional Science - 10
BIOLOGY
Endocrine System
There are glands in our body that secrete hormones and regulate cellular metabolism,
reproduction, sexual development, heart rate, sugar level, digestion etc. The endocrine system
is a chemical messenger system of an organism consisting of hormones, the group of glands
that secrete those hormones directly into blood to regulate the function of distant target
organs. The branch of science that deals with the study of the structure, secretion and functions
of different endocrine glands is called Endocrinology. There are two types of glands found in
the human body:
i.
ii.
Exocrine glands: Exocrine glands
pour their secretions into a duct. For
example: sweat glands, tear glands,
etc. These glands are present near
from the site of action and secrete
enzymes.
Endocrine glands: Endocrine glands
are richly supplied with blood
vessels and pour their secretions
(hormones) directly into the blood
vessels. These glands are often
called ductless glands. Example:
thyroid gland, adrenal gland. The
secretions of the endocrine glands
are called hormones.
Hormones
Hormones are chemical messengers that
are released into the blood stream by
the endocrine glands. Hormones control
or regulate many biological processes.
Although hormones reach all parts of the
body, only target cells respond to them
and regulate many biological processes.
fig: Endocrine glands
Fact with reason
Hormones are called chemical messengers, why?
Hormones are secreted by endocrine glands. They are secreted in one part of the body and
carried by the blood to another part where they stimulate or inhibit specific physiological
processes. So, hormones are called chemical messengers.
Characteristics of hormones
1.
2.
3.
Hormones may be protein or non-proteinaceous. They are composed of amino acids,
steroids, etc.
They are secreted as per the need but are neither excreted nor stored.
Hormones are transported by blood.
BIOLOGY
Optional Science - 10
307
4.
5.
6.
Hormones act either by stimulating or inhibiting the target organs.
They regulate long-term effects like growth, change in behavior, etc.
They are soluble in water and blood.
Functions of hormone
Hormones have following functions:
1.
Hormones regulate metabolic activities, glandular secretion, etc.
2.
They control Growth and development of body.
3.
They control reproduction by regulating the activities like gametogenesis, development
of the sexual characteristics, etc.
4.
Hormones conserve water and minerals in the body.
Memory Plus
Thomas Addison is considered as the ‘father of endocrinology’. He was the first who
reported a disease due to malfunction of adrenal gland known as Addison disease.
Major Glands of Endocrine System
Following are the major glands in human endocrine system:
1.
Pituitary
2.
Thyroid
3.
Parathyroid
4.
Adrenal
5.
Pancreas
6.
Gonads (Testes and Ovaries)
7.
Pineal
Hypothalamus
1.
Pituitary gland: The pituitary
gland is a small pea-sized gland
connected to the inferior portion of
the hypothalamus of the brain. The
pituitary gland is actually made up of
three completely separate structures:
the posterior, intermediate and
anterior pituitary lobes.
Bone
Anterior
lobeol
pituitary
Posterior
lobe of
pituitary
i. Anterior pituitary lobe:
Anterior
pituitary
Posterior
pituitary
fig: Pituitary gland
The anterior pituitary gland is controlled by the releasing and inhibiting hormones of
the hypothalamus. It produces six important hormones:
i.
ii.
iii.
308
Thyroid stimulating hormone (TSH): It stimulates the thyroid gland to produce
thyroxine hormone (T4) and triiodothyronine (T3).
Adrenocorticotropic hormones (ACTH): It stimulates the adrenal gland to
produce corticosteroids hormone.
Gonadotropins: Gonadotropins are hormones secreted by gonadotrope cells of
the anterior pituitary which regulate the functions of the gonads in both sexes.
These are:
Follicle stimulating hormone (FSH): It stimulates the follicle cells of the gonads
to produce gamates- ova in females and sperm in males.
Optional Science - 10
BIOLOGY
v.
vi.
Luteinizing hormone (LH): It stimulates the gonads to produce sex hormonesestrogen in females and testerone in males.
Human growth hormone (HGH): It acts on many target cells throughout the body by
stimulating their growth, repair and reproduction. It also stimulates cellular metabolism,
protein synthesis, mobilizes fats and inhibits glucose uptake. It is very important for
normal physical growth in children.
Effects due to hyposecretion: Deficiency of this hormone leads to dwarfism(small height
and sexual immaturity) and simmond's diseases (loss of body weight)occur
Effects of hypersecretion: Hyper-secretion leads to gigantism and abnormal size of the
hand, feet or face.
Prolactin (PRL): It stimulates the mammary glands to produce milk after child birth.
ii. Intermediate pituitary lobe:
The intermediate pituitary gland produces melanocyte stimulating hormone (MSH). It
stimulates the production and release of melanin pigment (melanocytes).
Breast
Adrenal
cortex
Skin
-......:.._ Prolactin . /
-Oxytocin
--ADH~
Bone
.---
GH
/
\
Thyroid
iii. Posterior pituitary lobe:
Testicle
fig: Hormones from pituitary gland
The posterior pituitary gland is a small extension of the hypothalamus. This gland
releases the following hormones:
Oxytocin hormone:
i.
ii.
iii.
It is responsible for uterine contractions during child birth. Therefore, it is also
known as birth hormone.
It helps in the release of milk during breast feeding.
In males, it helps in the transportation and ejection of sperms.
Antidiuretic hormone (ADH): It helps in preventing water loss in the body by
increasing the absorption of water in the Kidneys and reducing blood flow to sweat
glands.
BIOLOGY
Optional Science - 10
0
309
Fact with reason
Pituitary gland is called the 'master gland', why?
Pituitary gland takes messages from the brain through hypothalamus and uses these
messages to produce hormones. These hormones stimulate all the other hormone-producing
glands to produce their own hormones. So, pituitary gland is called the ‘master gland’.
2.
Thyroid gland: The thyroid gland is a butterfly-shaped gland located in the anterior
throat below larynx. It is found wrapped around the lateral sides of the trachea. The
thyroid gland produces three major hormones:
i.
Thyroxine or tetra-iodothyronine (T4): Its functions are:
a. Thyroxine hormone regulates the metabolic rate.
b. It regulates physical and mental development of the body.
c. It controls absorption of glucose from the intestine.
d. It regulates heat generation in humans by regulating respiration.
Effects due to Hyposecretion: Hypothyroidism
a. Cretinism: It is a condition characterized by retarded physical, mental and sexual
growth, slow heart beat, low blood pressure, decrease in body temperature, etc.
b. Myxoedema or Gull’s disease: It is the
condition of swelling of the skin and underlying
tissues. Person becomes fatty and sluggish.
Other effects are slow heart beat, low body
temperature and retarded sexual growth.
c. Goitre (Simple goiter): It is an abnormal
enlargement thyroid gland, thus swelling in
neck.
c. Hashimoto disease: It is an autoimmune
disease in which the thyroid gland is gradually
destroyed.
t;
\
\
'"'"'~
-- (
~
I
--I
Cartilage
Thyroid gland
Trachea
(windpipe)
fig: Location of thyroid gland
Effects due to Hypersecretion: Hyperthyroidism
ii.
310
Grave’s disease (Exopthalmic goiter or Parry’s disease): The over secretion of
thyroxin causes exophthalmic goitre or grave’s disease. Its symptoms are higher
metabolism, restlessness, decrease in body weight, bulging of the eyes, insomnia,
nervousness, high heart rate and high body temperature.
Calcitonin: Calcitonin gets released when there is a rise in calcium ion levels in the
blood. Its functions is to reduces the concentration of calcium ions in the blood by
helping the absorption of calcium into the bones.
Deficiency of calcitonin leads to the decrease of calcium level in bone by the
deposition of calcium in blood. It results in weakening of bones.
Optional Science - 10
BIOLOGY
iii.
3.
Tri-iodothyronine (T3): Tri-iodothyronine hormone regulates the body’s
metabolic rate. Increased level of T3 hormone leads to increased cellular activity
and energy usage in the body.
Parathyroid glands: Parathyroid glands
are four glands found on the posterior
side of either lobe of the thyroid gland. It
produces parathyroid hormone (PTH).
Function: Its function is just antagonistic
(opposite in nature) to calcitonin. It is
released when calcium ion levels in the
blood drop down. It stimulates the bone
cells to break down the calcium to release
free calcium ions into the bloodstream.
Th
~)
Ca~r
~
·
~
Thyroid (back view)
.
~
Trach-;;---(windpipe)_..,..---
fig: Location of parathyroid gland
Effects due to Hyposecretion: Hypoparathyroidism
It causes less concentration of calcium ions in the blood and tissues. The person will
suffer from painful jerking of muscles of neck, face, hands and feet. This condition is
called tetany.
Effects due to Hypersecretion: Hyperparathyroidism
It leads to more extraction of calcium from the bones and causes softening, bending
and fracture of the bones. This condition is called osteoporosis. Similarly, it can lead to
kidney stones due to excess deposition of calcium in kidney tubules and ureter. It also
leads to tumours.
4.
Adrenal glands (Suprarenal glands): The adrenal glands are a pair of roughly triangular
glands found above the kidneys. The adrenal glands are made up of two distinct layers:
the outer adrenal cortex and inner adrenal medulla.
i. Adrenal cortex: The adrenal cortex produces three hormones:
a.
Glucocorticoids: Glucocorticoids hormone is involved in the breakdown of
proteins and lipids to produce glucose. This increases the glucose level in blood.
It also aids in reducing inflammation and immune response. In case of excessive
bleeding, glucocorticoids hormone constrict blood vessels and balance the blood
pressure due to blood loss.
b.
Mineralocorticoids (Aldosterone): Mineralocorticoids hormone increases the
reabsorption of sodium from urine, saliva, bile and sweat to reduce its loss from
the body. Thus, it regulates the concentration of minerals, such as sodium and
potassium ions, in the body. It also increases the reabsorption of water from the
urine by raising the osmotic pressure of the blood through reabsorption of Na+ in
to it.
c.
Sex-corticoids: Sex-corticoids hormone secretes androgen hormone in the male.
In the female, it secretes oestrogen and progesterone hormones. These hormones
stimulate the development of secondary sexual characters like body hairs, menstrual
cycle, enlargement of the breast, change of voice in the male child.
BIOLOGY
Optional Science - 10
0
311
Memory Plus
In adult males, the amount of androgens produced by the testis is many
times greater than the amount produced by the adrenal cortex, leading to the
appearance of male secondary sex characteristics.
Effects due to Hyposecretion
a. Addisons disease: It is caused due to deficiency of mineralocorticoids. The
symptoms of this disorder are low blood sugar, low sodium ion concentration,
high potassium ion concentration, loss of weight, nausea, vomiting, etc.
b. Conn’s disease: It is caused by the deficiency of mineralocorticoids. It is related
with neural disorder, which can lead to convulsions and death.
Effects due to Hypersecretion
a. Cushings syndrome: It is caused by hypersecretion of glucocorticoides in
blood. The major symptoms of this syndrome are increase in blood sugar, blood
pressure, obesity, wasting of limb muscles, etc.
b. Aldosteronism: It is caused by hyper secretion of aldosterone, and its symptoms
are high sodium ion concentration and low potassium ion concentration in the
plasma, increase in blood volume, blood pressure, etc.
c. Adrenal virilism: It is caused by hyper
secretion of sex corticoids. In females, excess
androgen production leads to the development
of male secondary sexual characters, such as a
beard, moustache and hoarse voice.
ii. Adrenal medulla:
The adrenal medulla produces two hormones:
Adrenaline (epinephrine) and nor-adrenaline (norepinephrine). Both these hormones help to increase
the flow of blood to the brain and muscles to fight
stress. These hormones are responsible for increasing
the heart rate, breathing rate and blood pressure when
there is decrease in the flow of blood.
These hormones help our body to act in emergency
situations like fear, fligh, fight, anger, etc. Therefore
adrenal glands are also called emergency glands.
5.
I
kidney
fig: Adrenal gland and adrenal medulla
Pancreas: The pancreas is a large gland located in the abdominal cavity behind the
stomach. The pancreas is a heterocrine gland as it contains both endocrine and exocrine
tissues. The islets of Langerhans of the pancreas act as the endocrine cell. It secretes
insulin, glucagon and somatostatin hormones directly into the bloodstream. Insulin
lowers the blood sugar level while glucagon raises the blood sugar.
There are three types of cells within islets of Langerhans: alpha cells, beta cells and delta
cells.
312
Optional Science - 10
BIOLOGY
i.
Alpha cell: It produces glucagon hormone. This hormone is responsible for raising
blood glucose levels. Glucagon triggers muscle and liver cells to break down the
polysaccharide glycogen to release glucose into the bloodstream.
ii.
Beta cell: It produces insulin hormone.
When the blood level of glucose rises,
beta cells secrete insulin, which increases
the rate of glucose uptake and cellular
metabolism. It alos increases the protein
metabolism. Insuline also stimulates
deposition of extra glucose in the form
of glycogen in liver and muscle.
iii.
Gamma cell: It produces somatostatin
hormone. It is responsible for controlling
the activity of insulin as well as of
glucagon.
Pancreatic islets
Normal islet
beta cells destroyed
fig: Pancreas cells
Effects due to Hyposecretion
Hyposecretion of insulin results in diabetes mellitus (DM). It is caused due to high
level of glucose in blood (hyperglycaemia). It affects several organs like kidney,
eye, brain, etc. The symptoms of DM are: frequent urination, intense thirst,
weakness, loss of weight, slow healing of wounds, or even diabetic coma, etc.
Effects due to Hypersecretion
Hypersecretion of insulin or deficiency of glucagon results in hypoglycemia (low
blood glucose level) and eventually insulin shock. Its symptoms include dizziness,
fainting, convulsions, diabetic coma due to low glucose, brain damage and even
death.
6.
Gonads (Testes and Ovaries): The gonads are the ovaries in females and testes in males.
They are responsible for producing the sex hormones of the body.
a.
Testes: (singular: testis): The testes are the two balllike glands present on the either side of the scrotum.
They have tubules in them called seminiferous
tubules in which sperms develop. The seminiferous
tubules secrete testosterone and androgen hormone.
The testosterone stimulates spermatogenesis
and production of sperms. It also controls the
development of secondary sexual characteristics
like growth of penis and scrotum, beard, moustache,
hoarse voice, pubic hair, etc.
b.
Ovaries (singular: ovary): Ovaries are the two
gonads on either side of the lower abdomen near
the fallopian tubes in females. They produce eggs
and also many female sex hormones like oestrogen
and progesterone.
BIOLOGY
Spermatocele---.,;;...Epididymis---;~~ 111!!1'' .r
Testicle --_,_~
Scrotum-- -+,.__
fig: Testicle
fig: Ovaries
Optional Science - 10
313
The oestrogen stimulates the maturation of eggs, development of secondary
sexual characteristics like shrill voice, pubic hair, enlargement of breasts, soft
skin, etc. Similarly, the progesterone helps in the formation of the placenta during
pregnancy, releases egg during ovulation, prepares the uterus for the delivery of
a baby and controls the development of mammary gland buds.
7.
Pineal gland: Pineal gland is a small pine-cone shaped gland. It is found posterior to the
thalamus of the brain. It produces melatonin hormone. This hormone helps to regulate the
sleep-wake cycle of humans (circadian rhythm).This hormone is only produced in low light
or darkness. Hyper-secretion of this hormone causes humans to feel drowsy at night.
Answer writing skill
1.
Write the scientific name of the rat.
The scientific name of the rat is Rattus rattus.
2.
What is alimentary canal?
Alimentary canal is a pathway by which food enters the body and solid wastes are
thrown out. It is a tube running from the mouth to the anus.
3.
What is insulin?
Insulin is a hormone secreted by the pancreas, which converts glucose in the liver and
muscles.
4.
Give the scientific name of the rice plant.
The scientific name of the rice plant is Oryza sativa.
5.
Write the differences between endocrine and exocrine glands.
The differences between endocrine and exocrine glands are as follows:
Exocrine gland
Endocrine gland
Exocrine gland pours its secretions into a Endocrine gland pours its secretions
duct.
directly into the blood vessels.
It is called a duct gland.
These glands are often called ductless
glands.
The secretions of the exocrine gland are The secretions of the endocrine glands are
called enzymes.
called hormones.
6.
Write the function of bile.
The functions of bile are as follows:
0
314
a)
It helps in the digestion of fats
b)
It eliminates waste products from the blood.
Optional Science - 10
BIOLOGY
7.
What is the function of thyroid stimulating hormone (TSH)?
Thyroid stimulating hormone stimulates the thyroid gland to produce thyroxine
hormone (T4) and triiodothyronine (T3).
8.
Write short notes on thyroxine hormone.
Thyroxine hormone is secreted by the thyroid gland. It is also known as tetraiodothyronine (T4) hormone. The hyposecretion (hypothyroidism) of thyroxine leads
to goitre and hypersecretion (hyperthyroidism) causes Graves’s disease.
The functions of thyroxine hormone are:
9.
a)
b)
It regulates the metabolic rate of a body.
It plays a significant role in the mental and physical development of a body.
c)
It also plays a role in the absorption of glucose from the intestine.
What are the characteristics of a hormone?
The characteristics of hormones are:
10.
a)
Hormones may be protein or non proteinaceous.
b)
Hormones act either by stimulating or inhibiting the target organs.
c)
They regulate long-term effects like growth, change in behavior, etc.
What are gonads? Which hormone is secreted by them? Write its function.
The gonads are the ovaries in females and testes in males. They are responsible for
producing the sex hormones of the body.
In the female, the ovaries secrete oestrogen and progesterone hormones and in the
male, the testis secrete testosterone and androgen hormone.
The functions of these sex hormones are:
a)
These sex hormones determine the secondary sex characteristics of adult females
and adult males.
b)
Progesterone maintains the menstrual cycle. It promotes maturation of the female
reproductive organ. It thickens the uterine wall during pregnancy.
c)
Testosterone promotes maturation of the male reproductive organs, stimulates
spermatogenesis and production of sperm.
BIOLOGY
Optional Science - 10
315
Exercise
Section "A"
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
What is digestive system?
What is alimentary canal?
Define digestion.
What do you understand by coprophagy?
What is the function of the glottis?
What is the function of the ureter?
What is spermatic cord?
Write the function of:
a. Thyroid gland
b. Adrenal glands
d. Parathyroid gland
e. Gonads
What do seminal vesicles secrete?
Give the family of the rice plant.
What is tillering stage?
Define endocrine system.
Where is pituitary gland located?
What is endocrinology?
What is a hormone?
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
List the organs present in the alimentary canal.
What are the organs associated with the respiratory system of a rat?
What are the organs of the urinary system in a rat?
List the organs of the male reproductive system.
List the organs of the female reproductive system.
What are the stages of the life cycle of a rice plant?
What do you mean by booting stage?
List the glands associated with the endocrine system.
List the major parts of pituitary gland with two hormones secreted by each.
Pituitary gland is often called as the “master gland”, why?
Why is endocrine glands also called ductless gland?
c. Pineal gland
f. Pancreas
Section "B"
316
Optional Science - 10
BIOLOGY
12.
13.
14.
15.
16.
Pancreas is a heterocrine gland. Give reason.
Write the secretion of gastric glands.
What is the role of gastric glands in digestion?
What are secreted by the intestinal glands?
What is the role of pleural fluid?
Section "C"
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
Write short notes on the liver of a rat.
Write about the secretion of the pancreas.
Write the function of insulin.
Write the function of the salivary glands in digestion.
Give a short account of a rat’s kidney.
Give a short account ofthe adrenal gland and its secretion.
Write the functions of progesterone and testosterone hormones.
Write the difference between exocrine and endocrine glands.
What are the differences between the alpha and beta cells of the pancreas?
Write short notes on the pineal gland.
Section "D"
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
Describe the external features of a rat.
Explain the process of digestion in a rat.
What are the roles of organs of excretory system of rats?
Give a short account in male and female reproductive
organs in rats.
Explain the process of respiration in a rat.
What do you understand by urogenital system?
Explain the stages of the life cycle of a rice plant.
Describe the structure of rice plant.
Write the hormones secreted by the thyroid gland and the
function.
Which hormone is secreted by the parathyroid gland? Give
the function.
Name the glands in the the given figure alongside.
How pancreas helps to maintain the blood glucose level? Explain.
Complete the following table.
Pituitary gland
Hormone
functions
Anterior pituitary gland
Posterior pituitary gland
Intermediate pituitary gland
BIOLOGY
Optional Science - 10
317
Multiple choice questions
1.
The reproductive stem is called
a. Spike
b. Hull
c. Tiller
d. Embryo
The outer protective coat of rice is
a. Hull
b. Tiller
c. Spike
d. Pellicle
Hormones that stimulates the follicle cells of the gonads to produce gametes- ova in
females and sperm in males:
a. Adrenocorticotropic hormones
b. Follicle stimulating hormones
c. Luteinizing hormones
d. Prolactin hormones
Hyposecretion of thyroxin leads to
a. Goitre
b. Graves’s disease.
c. Calcitonin
d. Softening of bones
Hypersecretion of parathyroid hormone cause
a. Hyperparathyroidism
b. Hyperthyroidism
c. Hypoparathyroidism
d. Hypothyroidism
The islets of Langerhans of pancreas act as the
a. Heterocrine gland b. Homocrine gland
c. Exocrine gland
d. Endocrine gland
The hormone produced by the ovaries:
a. Oestrogens
b. Androgens
c. Testosterone
d. Melatonin
The cells of a liver are called
a. Hepatocytes
b. Oestocytes
c. Chondrocytes
d. Melanocytes
2.
3.
4.
5.
6.
7.
8.
9.
Exchange of gases takes place in
a. Alveoli
10.
b. Bronchioles
c. Lungs
d. Trachea
c. Glomerulus
d. Adrenal
The functional unit of the kidneys
a. Nephrons
11.
b. Capsule
Saliva contains the enzyme …… that helps to digest the starch present in the food.
a. Amylase
12.
b. Trypsin
c. Ptyalin
d. All
The condition of softening, bending and fracture of bone.
a. Osteoporosis
b. Decalcification
c. Bone deformation d. Oesteocytes
Project Work
1.
2.
Pay a visit to a field. Collect some ideas about rice plantation, the month and method
for doing so, ripening time, transplantation of seedlings and ways to protect the rice
plants. Prepare a report on it and submit it to your teacher.
Make a model showing the digestive, respiratory, urinary and reproductive parts of a rat.
318
Optional Science - 10
BIOLOGY
UNIT
16
HEREDITY
Hugo Marie de Vries (1848-1935) was born on February 16, 1848 in Haarlem, the
Netherlands. He was a Dutch botanist and one of the first geneticists. He is famous for
suggesting the concept of genes and rediscovering the laws of heredity in the 1890s. He is
the one who introduced mutation and developed the mutation theory.
·······························································••••••••••••••••••••······················································
Syllabus issued by CDC
Learning objectives:
At the end of this unit, the students will be able to:
• describe Mendel’s dihybrid cross and
Mendel’s law along with the diagram.
Atomic mass, molecular mass and • define chromosome, sex-linked inheritance
and twins.
mole concept
• describe the process of sex-linked inheritance
and formation of twins.
Theory
Practical
6
2
Key terms and terminologies of the unit
Heredity: This phenomenon of transmitting parental characteristics to the offspring is called
heredity.
Variation: The difference between parents and the offspring or between individuals in a species is
called variation
Genetics: The branch of science which deals with the study of heredity and variation is called
genetics.
Dihybrid cross: A cross between the two individuals that differ in gene by considering two pairs
of contrasting characteristics is called dihybrid cross.
Hybrids: Hybrids are the organisms produced when two genetically different organisms are
crossed.
Hybridization: The process of crossing two alternating characteristics is called hybridization. It can
also be defined as the process by which hybrids are formed.
Genotype: The genetic composition of an organism is called genotype.
BIOLOGY
Optional Science - 10
319
Phenotype: The characteristics which appear externally are called phenotype.
Linkage: Linkage can be defined as the phenomenon of association between two or more genes
present in the same chromosome that were inherited together from one generation to another
transmitting the characteristics as an inseparable unit.
Autosomes: The chromosomes which are responsible for all the characteristics except sex
determination.
Allosomes: The chromosomes which determine the sex of the offspring are called allosomes.
Sex-linked gene: Genes that are carried by sex chromosome (X or Y) are called sex linked gene.
Sed-linked characteristics: The characteristics which inherit due to sex linked gene are called sexlinked characteristics.
Sex-linkage: The inheritance of non-sex determining characteristics along with sex chromosomes
is called sex linked inheritance or sex linkage.
X-linked inheritance: The inheritance of genes for non-sexual characteristics through X sex
chromosome is called X-linked inheritance
Y-linked inheritance: The inheritance of genes for non-sexual characteristics through the Y-sex
chromosome is called Y-linked inheritance.
Colour blindness: Color blindness is a disorder in which a person cannot distinguish red, green,
or both colors from other colors.
Haemophilia: Haemophilia is a sex-linked disease in which blood loses its ability to clot on
exposure to air.
Multiple birth: This process of giving birth to more than one baby is called multiple births.
Twins: Twins are two babies reproduced by the same pregnancy.
Identical twins: If twins are developed from the same ovum then they are called identical twins or
monozygotic twins.
Fraternal twins: The twins which are formed by the fertilization of two different ova by two
different sperms are called fraternal or dizygotic twins.
Introduction
All organisms have characteristics of their parents. These characteristics are transmitted
from the parents to the offspring during the formation of gametes and then to the zygote.
This phenomenon of transmitting parental characteristics to the offspring is called heredity.
Besides the phenomenon of heredity, all the organisms look different. This is possible due to
some new characteristics developed in an individual. And this difference between parents and
the offspring or between individuals in a species is called variation.
Variatin is caused by the environmental factors too. Organisms when adjust with their
environment, there is development of some special features in the body of organisms.
Thus, variation is an essential phenomenon for adaptation. Both the genetic variation and
environmental variation play an important role in the development of a body. The branch
of science which deals with the study of heredity and variation is called genetics. Due to the
phenomenon of variation, each and every individual is different in this world.
Mendel performed experiments by crossing pea plants to give his laws of heredity. In this
unit, we will learn about dihybrid cross, Mendel’s law of inheritance, chromosome, sex-linked
inheritance and how twins are formed.
0
320
Optional Science - 10
BIOLOGY
Mendel’s Experiment
An Austrian monk, Gregor Johann Mendel (1822-1884), studied how characteristics are
transmitted from the parents to the offspring. Since the offspring contain half the chromosomes
from the mother and half from the father, which characteristicswill they actually show? And
why? To solve these questions, he conducted many experiments on the garden pea plant
(Pisum sativum). On the basis of his experiments on the pea, he explained the term genetics
and the pattern of transmitting hereditary characteristics, and gave the laws of heredity. For
this contribution, Mendel is also called the 'Father of Genetics'.
Fact with reason
Mendel is called the 'father of genetics', why?
Mendel was the first to perform scientific experiments in pea plants for the study of transfer
of genetic character in offspring. He recognized the dominant and recessive genetic traits
through his experiments. Mendel discovered that the genetic characteristics are passed
from parent to offspring in a measurable and predictable way. He was the first to give laws
of heredity in a systematic way. So, Mendel is called ‘father of genetics’.
Contrasting Characteristics in Pea Plants
The pair of alternate characteristics in an organism are called contrasting characteristics.
Mendel selected 7 pairs of contrasting characteristics of the pea plant for his experiment.
These characteristics are as follows:
Size of the plant: tall and dwarf
Position of flowers: axial and terminal
Shape of mature seeds: round and wrinkled
Color of the flower: purple and white
Color of the seed: green and yellow
Shape of the mature pods: inflated and constricted
Color of the mature pods: yellow and green
Fact with reason
Why did Mendel select garden pea plants for his experiment?
The following characteristics of the pea plant made Mendel to choose it for his experiment:
1.
Short life cycle: Pea plants have a short life cycle. So many generations can be studied
in a single year.
2.
Bisexual plant: Pea plants are bisexual plants. So plants can easily self-pollinate or
cross-pollinate to obtain successive generations.
3.
Productivity: A large number of offspring plants are produced in each generation.
4.
Easy to cultivate
5.
Variety of characteristics: Pea plants have varieties of pairs of contrasting
characteristics.
BIOLOGY
Optional Science - 10
321
The table given below shows the seven paris of contrasting characteristics in parental pea
plants (P). It also shows the results of mendel's experiment in which pea plants were crossed
by considering one pair of contrasting characteristics (monohybrid cross). The expressed
characteristics in the first filial generation (F₁) are the dominant characteristics.
Podcolot
p
Purple
Yellow
Round
X
X
X
G,ecn
W11nklcd
While
Tc,m,nal
lnfi11ed
Green
1,1
Const1ic1cd
Yellow
Dwa,f
I-
1
Pu,pte
Axial
Yellow
Round
l t. )J
fig: Mendel's experiment on the basis of seven pairs of contrasting characteristics in pea plant
Mendel’s Dihybrid Cross
We have already learnt about monohybrid cross, Mendel's law of dominance, and Mendel's
law of purity of gametes (or law of segregation). Here we will learn about dihybrid cross and
Mendel's law of inheritance (law of independent assortment) in this unit.
A cross between the two individuals that differ in gene by considering two pairs of contrasting
characteristics is called dihybrid cross. For a dihybrid cross, Mendel selected two pairs of
characteristics in pure pea plant as: the shape of the seed and seed colour. He first carried
out self-pollination followed by cross-pollination and observed the results of the consecutive
generations.
Mendel chose two homozygous pea plants, one having round seeds with yellow colour
(RRYY) and another having wrinkled seeds with green colour (rryy). Then he cross-pollinated
these two plants and got the F1-generation. In the F1-generation, he found that all the plants
had round seeds with yellow colour, but their genotype was heterozygous (i.e. RrYy). With
this result, he concluded that the round seed was dominant over the wrinkled seed. Similarly,
the yellow colour was dominant over the green colour.
According to Mendel’s law of purity of gametes, genes in heterozygous plants separate at the
time of gamete formation in their reproductive parts (androecium and gynoecium). The four
possible gametes (male and female) from the heterozygous plant (RrYy) are RY, Ry, rY and ry
for F₂-generation. Then for the F2-generation, he allowed the offspring of the F1-generation to
self-pollinate and observed the results of the F2-generation. The entire process can be studied
in the following phylogenetic chart:
0
322
Optional Science - 10
BIOLOGY
Parents
Round seed with yellow colour
Wrinkled seed with green colour
•
!
Genotypes
RRYY
rryy
Gametes
RY
!
ry
Hybrid plants with round
and yellow coloured seed
Cross-pollination
RrYy
Gametes
(for F2-generation)
l
!
l
I
Ry
RY
l
rY
ry
Self-pollination
F2-generation (in Punnett square):
RY
Ry
rY
ry
RY
RRYY 0
RRYy 0
RrYY 0
RrYy 0
Specification: Round Yellow
Ry
RRYy J
RRyy
RrYy ,J
Rryy
•
•
•
•
Round green
rY
RrYY 0
RrYy \)
rrYY
rrYy 0
ry
RrYy ~
Rryy
rrYy
rryy
Wrinkled yellow
Wrinkled green
•
•
••
•
•
The phenotypic and genotypic results in F2-generation of the dihybrid cross were as follows:
Phenotype
Form
Genotype
Number of individuals
Round seed with
yellow colour
Homozygous (pure)
RRYY
1
Heterozygous
(Hybrid)
RRYy
RrYY
RrYy
2
2
4
RRyy
Rryy
1
2
rrYY
rrYy
1
2
rryy
1
Genotypic ratio:
1:2:2:4:1:2:1:2:1
Total:
Round seed with
green colour
9
Pure
Hybrid
Total:
Wrinkled seed with
yellow colour
Total:
Wrinkled seed with
green colour
Total:
Phenotypic ratio:
3
Pure
Hybrid
3
Pure
1
9:3:3:1
BIOLOGY
Optional Science - 10
0
323
Result: As a result of Mendel’s dihybrid cross, he found the phenotypic ratio as
Round yellow seeded: Round green seeded: wrinkled yellow seeded: wrinkled green seeded
= 9:3:3:1
The genotypic ratio is 1:2:2:4:1:2:1:2:1.
Conclusion: In the F₁-generation, Mendel found all round seeds with yellow colour, but their
genotype was heterozygous (i.e. RrYy). In the F₂-generation, he found four different types
of pea plants - round seeds with yellow colour, round seeds with green colour, wrinkled
seeds with yellow colour and wrinkled seeds with green colour in the ratio of 9:3:3:1. This
result shows that the pair of alleles(alternative forms of a gene) segregate from each other and
combine with another allele independently, forming a new set of characteristics. On the basis
of this result, Mendel formulated the law of independent assortment.
Mendel’s law of independent assortment (law of free recombination)
It states that the different characteristics in a hybrid union are inherited independently and
when two pairs of traits are followed in the same cross, they assort/combine independently”.
For example, in the above dihybrid cross:
Total round seeded = 9+3=12
Total yellow seeded = 9+3=12
Total wrinkled seeded = 3+1 =4
Total green seeded = 3+1 =4
Round seeded: wrinkled seeded = 3:1
Yellow seeded: green seeded = 3:1
He also suggested that the genes responsible for different characteristics can separate from
each other and form a new combination of genes in the offspring. This concept has been
implemented in the agricultural field to develop new and advantageous characteristics in
crops as well as in animals to improve their productivity.
Limitation of Mendel’s law of Independent Assortment
According to Mendel’s law of independent assortment, every gene assorts with another gene
independently. But this phenomenon is only true when those genes are present in two different
chromosomes not when those genes are present in the same chromosome. As we know that a
single chromosome contains many genes, those genes are linked with each other and
transmitted as a single unit. These genes, which are transmitted together, are called linked
genes, and this phenomenon is called linkage. Hence, linkage can be defined as the phenomenon
of association between two or more genes present in the same chromosome that were inherited
together from one generation to another transmitting the characteristics as an inseparable unit.
Genes that are located on the same chromosome are not free to
participate in independent assortment. Thus, Mendel's law of
independent assortment cannot be applied in case of linked genes.
Sex-linked Inheritance
Linked
Not Linked
Sex chromosomes (X and Y) not only carry the genes that determine male and female traits but
also those for some other characteristics as well. Genes that are carried by sex chromosome (X
or Y) are called sex linked gene. Among the two sex chromosomes (X and Y), X-linked genes
are much more common than Y-linked genes. These genes of non-sexual characteristics are
transmitted from one generation to another generation along with the sex chromosome. The
characteristics which inherit due to sex linked gene are called sex-linked characteristics.
324
Optional Science - 10
BIOLOGY
The inheritance of non-sex determining characteristics along with sex chromosomes is called sex
linked inheritance or sex linkage. Sex-linked inheritance can also be defined as the inheritance
of non-sexual characteristics determined by a gene present on either of the sex chromosome. It
was first explained by Bateson and Punnet in 1906.
Sex-linked Inheritance in Human
As other organisms, a human also develops from a single cell, called a zygote. A zygote is
formed by the fusion of the male gamete (sperm) and female gamete (ovum). Both the gametes
are formed by the gametogenesis process, where meiosis cell division reduces the number of
chromosomes to half (23) of the number of chromosomes present in the diploid cell (23pairs).
In case of a male gamete, out of 23 chromosomes present in the sperm, 22 are autosomes and
one is a sex chromosome(allosome) - either an X or a Y. But in case of a female gamete, out of
23 chromosomes present in the ovum, 22 are autosomes and the sex chromosome is always an
X. When these gametes are fertilized, the following process occurs:
1.
X from the father and X from the mother fertilize to form a girl.
2.
Y from the father and X from the mother fertilize to form a boy.
3.
X chromosome is never transferred from the father to a boy.
4.
Y chromosome is always transferred from the father to a boy.
Mother
(XX)
Father
(XY)
X
X
X
Y
XX
(Girl)
XY
(Boy)
XX
(Girl)
XY
(Boy)
In human beings, sex-linked characteristics can be transmitted from either the X or Y
chromosomes. Both the men and women have the probability to get sex-linked gene. In case
of Y-linked gene, only men can inherit it. But X-linked gene can get inherited in both men and
women since both inherit X chromosomes.
Types of Sex-linked Inheritance
There are three types of sex-linked inheritance:
1.
X-linked inheritance: The inheritance of genes for non-sexual characteristics through
X sex chromosome is called X-linked inheritance. Such characteristics are transmitted
to the male where females are the carriers. Examples of X-linked inheritance are
haemophilia, congenital night blindness, baldness in males, Duchenne muscular
dystrophy, red-green color blindness.
BIOLOGY
Optional Science - 10
0
325
2.
Y-linked inheritance: The inheritance of genes for non-sexual characteristics through
the Y-sex chromosome is called Y-linked inheritance. This inheritance only occurs in
male from male. Hypertrichosis (hairy ear), TDS (testis determining region), etc. are
examples of Y-linked inheritance.
3.
X-Y linked inheritance: It is the inheritance of genes for non-sexual characteristics
through both homologous chromosomes X and Y. Examples of this type of inheritance
are complete color blindness, skin cancer, etc. This type of sex linkage is also called
incomplete sex linkage because for a characteristic to occur in the offspring, both the
chromosomes - X as well as Y - must contain the same gene. If anyone of them lacks that
gene, then the characteristic won’t be observed in the offspring.
Memory Plus
Disorders caused by sex-linked inheritance are called sex-linked disease. Eg.
Haemophilia, color blindness, hypertrochosis, etc.
There are about 120 sex linked genetic disorders have been identified till now. Among
those the most common sex linked traits are colour blindness and haemophilia.
Fact with reason
X-linked human genetic disorders are much more common in males than in females, why?
X-linked genetic disorders are due to inheritance of X-linked gene. Males only have one X
chromosome. The inherited X-linked gene gets expressed in males and shows its effect. On
the other hand, females have two X-chromosomes. There is a probability of being X-linked
gene as a recessive which gets suppressed by the genes in a normal X chromosome. So,
X-linked human genetic disorders are much more common in males than in females
Characteristic features of inheritance for a sex- linked trait
The characteristic features of the transmission of sex-linked traits to the offspring are:
1.
The gene responsible for sex-linked characteristics (X-linked gene) is never transmitted
from the father to a son because the son not only receives the Y-chromosome from the
father but also receives the X-chromosome from the mother.
2.
A male with X-linked, dominant allele (Affected father)
transmits his sex-linked genes (i.e., X-linked genes) to
all his daughters, since females receive one of their two
X-chromosomes from father. These daughters, in turn,
transmit this gene to half of their male progeny. Thus,
a X-linked dominant gene is transmitted from a male
to its female progeny, and thereafter to half of the male
progeny of such females. All X-linked genes therefore
pass from male to female and then come back to a male
of F₂ generation (grand-children generation).
Xlioked.
d~::::,'1•thec
allele
------
0 ""1f1ected
I
allele
XY
XX
□ Affec ted
Ou,affected ~
l\
w11 w,i I 1
I
Unaffected
son
Affected Unaffected
daugther
son
Pass trait from female progeny
Father (affected)
Grandson (affected)
326
Optional Science - 10
BIOLOGY
mot.hoc
- Recessive
Affected
daugt her
3.
A female with X-linked, recessive allele (Unaffected carrier
mother) transmits her sex-linked genes (i.e., X-linked genes)
to the half of male progeny (sons) in the F1-generation and
to the half of female progeny(daughters). Sons get affected
but the unaffected daughters will become carriers like their
mother. These sons, in turn, transmit this gene to the female
progeny in the F2-generation.
I-
Dommoo<11
allele
X•"°'"·
rece5siveallele
XY
□ Affected
XX
Ounaffe<:ted
oc,rr;e,
~
tQIQ ~ II
Pass trait from male progeny
Mother (carrier)
Granddaughter (affected)
A female with X-linked, dominant allele (Affected mother) transmits her sex-linked
genes (i.e., X-linked genes) to the half of male progeny (sons) and to the half of female
progeny(daughters) in the F1-generation. All of these sons and daughters get affected.
Unaffected
son
4.
carrier mother
""'"""'·
Oo.ffec<edfa<hv•
Unaffected Affected
daugther
son
Unaffected.
carrierdaugther
Cause of Sex Linkage
If we study the structural features of the sex chromosomes in a
human cell, then we will find that there are two parts in between
in X and Y chromosomes. They are homologous segment and nonhomologous segment. The long arm of the Y-chromosome and
the short arm of the X-chromosome are the homologous segments
whereas the remaining segments are non-homologous.
Genes located in the homologous segment of the X chromosome
do not show sex-linked inheritance because it is a recessive gene
segment. Any gene present in the non-homologous segment causes
a different sex-linked inheritance.
homologous
Nonpart
{
~
•
,
l
Homologou:{- : - : part
•
I~
M atern1I
•
: Patcnial
fig: Male sex chromosomes
(XY) with homologous and
non-homologous parts
If a few genes are found in the non-homologous segment of the Y-chromosome, which have
no allele in X-chromosome then a different pattern of inheritance is shown, called Y-linked
inheritance. For example, hypertrichosis, TDS, etc. Similary, if a gene is present on the Xchromosome, but no allele in Y-chromosome then it is said to be X-linked inheritance.
Thus, the two causes of sex linkage are:
1.
The location of a gene in the X chromosome and the absence of its allele in the Y
chromosome (X-linked inheritance)
2.
The location of a gene in the non-homologous region of the Y chromosome and the
absence of its allele in the X chromosome (Y-linked inheritance)
Color Blindness in Human
Color blindness is a disorder in which a person cannot distinguish red, green, or both colors
from other colors. The human eye actually detects only three colors; red, green and blue, which
are mixed by the brain to form different colors. Among these three pigments, red and green
lie close together in the X-chromosome, and hence the most common type of color blindness
in humans is caused by the red and green pigments, which is called red-green color blindness.
Since both these pigments are located in the X-chromosomes, this defect is a recessive and
X-linked defect.
BIOLOGY
Optional Science - 10
0
327
We can study the pattern of transmitting this defect with the help of the crisscross method.
Let us assume that the genotype for a normal female is XX, color blind female is XcXc, carrier
female XcX, color blind male (XcY) and normal male (XY).
If a color blind male (XcY) marries a normal woman (XX), then all male progenies will be
normal (XY) and all female progenies will be carriers in the F1-generation. If the carrier female
(XcX) marries a normal male (XY), then there will be four possibilities - one a carrier female
(XcX), one a normal female (XX), one a normal male (XY) and the other a color blind male (XcY)
in the F2-generation.
Colour blind Male
(XCY)
Normal Female
(XX)
Y
XC
XCX
(Carrier Female)
XCX
(Carrier Female)
X
X
XY
(Normal Male)
XY
(Normal Male)
Carrier Female
(XCX)
Normal Male
XY
X
XC
XCX
(Carrier Female)
F1-generation
(
_)
XCY
(Colour blind male
X
Y
XX
(Normal Female)
XY
(Normal Male)
Result of theF₂-generation: Among the female
progenies, half of them will be carriers and half
of them will be normal. Similarly among the
males, half of them will be normal and half will
suffer from color blindness.
F2-generation
(
_ ,)
a
normal •
oolor
vision ff
•
female 4'
carrier ff
If a color blind female (XcXc) marries a normal male
(XY), then there is a 50% chance of getting a carrier
female (XcX) and 50% chance of getting a color blind
male (XcY) in the F1-generation.
fig: Red-Green colour Blindness inheritance pattern
328
Optional Science - 10
BIOLOGY
Normal Male
( XY)
Colour blind Female
(XCXC)
I\
XC
XC
XCXC
(Carrier Female)
XCY
(Colour blind male
X
Y
XCX
(Carrier Female)
XCY
(Colour blind Male)
If a carrier female (XcX) marries a color blind male, then there is a 25% probability of each of a
color blind female, color blind male, carrier female and normal male.
Carrier Female
(XCX)
I\
XC
Colour blind male
(XCY)
X
XCXC
XCY
(Colour blind Female) (Colour blind male)
XC
Y
XCX
(Carrier Female)
XY
(Normal Male)
If a colour blind female (XcXc) marries a color blind male (XcY), then all the offspring will suffer
from color blindness in the upcoming generation.
Colour blind male
(XCY)
Colour blind Female
(XCXC)
XC
XC
Y
XC
XCXC
XCY
(Colour blind Female) (Colour blind male)
BIOLOGY
XCXC
(Colour blind female
XCY
(Colour blind Male)
Optional Science - 10
0
329
Haemophilia in Humans
Haemophilia is a sex-linked disease in which blood loses its ability to clot on exposure to
air. This disorder leads to prolonged bleeding and ultimately excessive loss of blood. This
disorder is also called the royal disease as it was first observed in Queen Victoria. One of her
sons, Leopold, suffered from haemophilia and died of it at the age of 31 years. This trait is also
an X-linked recessive trait. The pattern of this disease can also be discussed with the help of
the crisscross method.
Let us assume that the genotype for a normal female is XX, hemophilic female is XhXh, carrier
female is XhX, hemophilic male is (XhY) and normal male is (XY).
If a hemophilic male (XhY) marries a normal woman (XX), then all male progenies will be
normal (XY) and all female progenies will be carriers in the F1-generation. If a carrier female
(XhX) marries a normal male (XY), then there will be four possibilities - one a carrier female
(XhX), one a normal female (XX), one a normal male (XY) and the other a hemophilic male
(XhY) in the F2-generation.
Homophilic Male
(XhY)
Xh
Normal Female
(XX)
~(
F1-generationl
X
Y
XhX
(Carrier Female)
X
XhX
(Carrier Female)
XY
(Normal Male)
Carrier Female
(XhX)
Xh
0
330
Normal Male
(XY)
~(
F2-generationl
Y
X
XhX
(Carrier Female)
XY
(Normal Male)
X
XhY
(Homophilic Male)
Optional Science - 10
XX
(Normal Female)
BIOLOGY
XY
(Normal Male)
Result of the F₂-generation: Among the female progenies, half of them will be carriers and
half of them will be normal. Similarly among the males, half of them will be normal and half
will suffer from haemophilia.
Fact with reason
Haemophilia is called a sex-linked disease, why?
The genes associated with haemophiliac conditions are located on the X-chromosome,
which is one of the two sex chromosomes. Haemophilia is transmitted along with the sex
chromosome. A hemophilia female is the carrier of the gene responsible for the disease.
So, haemophilia is called a sex-linked disease.
Activity
Draw a crisscross diagram upto the F1-generation and find out the result of that
cross when a carrier female marries a normal male, hemophilic female marries a
normal male, hemophilic female marries a hemophilic male, carrier female marries a
hemophilic male.
Twins
Sometimes a mother gives birth to more than one baby, mostly two at a time. Sometime even
three or more at the same time from the same pregnancy. This process of giving birth to more
than one baby is called multiple births. Twins, triplets are examples of multiple births. Twins
are two babies reproduced by the same pregnancy.
Two types of twins
Twins can develop either from the fertilization of an ovum by a sperm or fertilization of two
different ova by different sperms. On the basis of fertilization, the two types of twins are:
identical twins and fraternal twins.
Identical Twins (Monozygotic twins)
pase.11aJ 6 6ila uo
t
t
s111(1sua111poe
qWOMu! nue1dw1
o.<Jqwa.<1ie3
Jlll!jSl!ldsua111 pue
qwOM. u1 nue1dw!
o..t,qwa.<1a3
[Fa]
t
t
S)H JIUU!lltJed1spu,
eiua,el(lp.JtljS
)H JI UU! fMJV'\{S pue
eiua,et(lp.JtljS
A
t
@)
qwo111u1
6u11ue1dw! IJOJitqSl!ldS
o..t,qwa..<1a3
t
S>H JiJUU!lltJeda,pue
se1ua,ef(la1titdas
BIOLOGY
®
First of all, fertilization occurs between the sperm
and mature ovum to form a zygote. During the
development of the embryo, the dividing zygote
splits into two and develop separately as two
different cells, forming two babies with identical
characteristics.
a
Formation of identical twins
'f.(:Jjl
'f.(ffj1
...______,f.....----------'
wJadsauo.<q
0\ pas m1JaJpueAle.-.owoJJ
If twins are developed from the same ovum then
they are called identical twins or monozygotic
twins. They are called identical twins because they
look similar and possess similar characteristics.
Idetical twins share exactly the same genes. So,
they look alike, although it may get changed with
increasing age due to environmental variation.
r
1.
fig: formation of identical twins
Optional Science - 10
331
2.
Fraternal Twins (Dizygotic twins)
The twins which are formed by the fertilization
of two different ova by two different sperms are
called fraternal or dizygotic twins. They are called
fraternal twins because they are not similar with
each other and are unique. They are the most
common type of twins.
Fraternal twins do not share the same genes as in
case of the identical twins. The genes from parents
tranfer independently to such twins. So, fraternal
twins are not exactly alike.
Formation of Fraternal Twins
In the female, multiple ova can mature at the same
time. If two sperms fertilize two different ova,
then both the fertilized ova undergo cell division
to develop into an embryo and later on into two
different babies, which are called fraternal twins.
They are called twins, but they have unique
individual characteristics.
v- 0
Two egg H eleased ~
from ovaries
0
!
Eachegg fertilised
by separate sperm
G) 0 /
0
Q
,.--/
!
Each embryo
implants in womb
separately
!
Sepa rate placentas
and separate inner sacs
fig: formation of fraternal twins
Fact with reason
Identical twins are also called monozygotic, why?
Monozygotic means single fertilized egg (zygote). Identical twins develop from one zygote,
which splits and forms two embryos. So, they are also called monozygotic twins.
Fraternal twins are also called dizygotic, why?
Dizygotic means two fertilized eggs (zygotes). Fraternal twins are developed from the
fertilization of two different zygotes at the same time. So, they are also called dizygotic.
Differences between identical twins and fraternal twins:
Identical twins
Fraternal twins
In case of identical twins, one zygote splits In case of fraternal twins, two different eggs
and forms two embryos.
are fertilized by two different sperm cells.
Identical twins always have the same gender. Fracternal twins usually have different gender.
Their appearance is extremely similar, Their appearance is as similar as any other
although it may get changed with the sibling.
increasing age due to environmental factors.
Their blood group is the same.
Their blood group may be different.
Factors that increase the probability of having twins
According to articles published, multiple births are becoming common nowadays, which can be
fraternal, identical or a combination of both. Among multiple births, twins are the most common
type. Twins may be both boys, both girls or one boy and one girl. The reasons behind the formation
of twins are:
332
Optional Science - 10
BIOLOGY
1.
Advancing age of the mother: Nowadays women marry in their 30s and some in their
40s. At this age,womensecrete higher levels of oestrogen (which helps in ovulation). So
multiple ova mature at the same time.
2.
Number of pregnancies: Multiple pregnancies also trigger multiple births, especially
twins.
3.
Heredity: If the mother herself is also a twin sister, either identical or fraternal, then she
can also conceive twins.
4.
Race: According to a study, African women have the highest incidence of twins.
5.
Assisted reproductive techniques: Nowadays techniques like stimulating the ovaries
with fertility drugs increase the number of ovulations at a given time.
Answer writing skill
1.
What isa hybrid?
A hybrid is an organism produced by crossing two pure parents.
2.
Define twins.
Twins are two babies produced by the same pregnancy.
3.
Write why twins are formed.
Nowadays women marry in their 30s or 40s. At this age,a woman’s body secreteshigher
levels of oestrogen (which helps in ovulation). So multiple ova mature at the same time.
Multiple pregnancies also trigger multiple births, especially twins.
4.
Write the differences between X-linked inheritance and Y-linked inheritance.
5.
X-linked inheritance
Y-linked inheritance
1. It is the inheritance of genes for non- 1. It is the inheritance of genes for nonsexual characteristics through X sex
sexual characteristics through Y sex
chromosome .
chromosome .
2. Usually, the characteristics are
2. This inheritance only occurs in male
transmitted to the male where
from male.
females are the carriers.
Write any two functions of chromosomes.
a) Chromosomes are the genetic materials which help in transmitting parental
characteristics to the offspring.
b) Sex chromosome determines the sex of the offspring.
6.
Write short notes on haemophilia.
Haemophilia is a sex-linked disease, in which blood loses its ability to clot on exposure
to air. This disorder leads to prolonged bleeding and ultimately excessive loss of blood.
This disorder is also called royal disease as it was first observed in Queen Victoria, who
carried the gene responsible for the disease. One of her sons, Leopold, suffered from
haemophilia and died of it at the age of 31 years. This is also an X-linked recessive trait.
The pattern of this disease can also be discussed with the help of the crisscross method.
BIOLOGY
Optional Science - 10
0
333
Exercise
_
_ _JQ___
--------
Section "A"
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
What is heredity?
Define dihybrid cross.
Define haemophilia.
What happens in color blindness?
What is sex chromosome?
Write the number of each of autosomes and allosomes in a normal human cell.
What does sex linkage mean?
Write any two examples of sex-linked disease.
Write the names of three types of sex linked inheritance.
State Mendel's law of independent assortment.
On which experiment was Mendel's law of independent assortment formulated?
Write down the genotypic and phenotypic ratio of the dihybrid cross in the F2 generation.
Section "B"
1.
2.
3.
4.
5.
6.
Differentiate between autosome and allosome.
What is the major difference between identical and fraternal twins?
Write Mendel's law of independent assortment and also write its limitation.
Why did Mendel choose the pea plant for his experiment?
When a woman with normal color vision (but her father is color blind) gets married to a
color blind man, then what are their chances of having color blind children?
What is the genotypic and phenotypic ratio of Mendel’s dihybrid cross?
Section "C"
1.
2.
3.
4.
5.
6.
Write short notes on Mendel's dihybrid cross.
What conclusion can you draw from the result obtained in the dihybrid cross of Mendel’s
experiment?
Write in short about the methods used to show sex-linked inheritance.
Explain the process of formation of identical and non-identical twins in humans.
Write any three reasons behind the formation of twins.
What happens when a hybrid plant with round seeds and inflated pods is allowed to
self-pollinate? Draw a chart and show the result in a ratio.
334
Optional Science - 10
BIOLOGY
Section "D"
1.
2.
3.
4.
1.
2.
What happens if a man with normal vision marries a color blind woman? Show the
phenotype and genotype of their children.
What is sex-linked disease? How does it get transmitted to the offspring? Explain with
a suitable diagram.
A homozygous plant having round seeds and inflated pods is first cross-pollinated
with a homozygous plant having wrinkled seeds and constricted pods and then selfpollinated. What result will be obtained in the 2nd generation? Show your result up to
the F2 generation with a proper chart.
A pure tall plant bearing red color flowers was crossed with a pure dwarf plant with
white flowers.
i. Draw a phylogenetic chart showing the above mentioned cross upto the F2 generation.
ii. What type of offspring will be produced in the F1 generation?
iii. Which law does it illustrate? State the law.
Explain the process how haemophilia gets transmitted from the parents to the offspring.
Explain the process how color blindness get transmitted from the parents to the offspring.
Multiple choices Question
1.
2.
3.
4.
5.
6.
7.
What is the phenotypic ratio of the result observed in the F2 generation of a dihybrid cross?
a. 9:3:2:1
b. 3:1
c. 1:2:2:4:1:2:1:2:1
d. 9:3:3:1
What is the genotypic ratio of the result observed in F2 generation of a dihybrid cross?
a. 9:3:2:1
b. 3:1
c. 1:2:2:4:1:2:1:2:1
d. 9:3:3:1
Why did Mendel choose the pea plant for his experiment?
a. It has a very short life cycle.
b. It is a bisexual plant.
c. It is easy to cultivate.
d. All of the above.
Who is the carrier of the hemophillic gene?
a. mother
b. father
c. both
d. none
Which one is an example of a sex-linked disease?
a. Baldness
b. HIV/AIDS
c. Cancer
d. Syphilis
Which one is not a sex-linked disease?
a. Haemophilia
b. Color blindness
c. Male pattern baldness
d. Malaria
Identical twins are formed from
a. single zygote
b. two different zygotse
c. two different mothers
d. none
Project Work
Collect information about a sex-linked disease like baldness or hemophilia or color
blindness from different sources. Study your family history if any member has the linkage
or not. If yes, then collect the pattern, present it in a report.
BIOLOGY
Optional Science - 10
335
UNIT
17
ECOLOGY
Eugen Warming (1841-1924) He was a Danish botanist. He was the first to figure out the
scientific discipline of ecology. He wrote the first textbook in 1895 on plant ecology and
taught the first university course on ecology and gave the concept in its meaning and
content. He wrote a number of textbooks on botany, plant geography and ecology.
Syllabus issued by CDC
Learning objectives:
At the end of this unit, the students will be able to:
• describe the simsar ecosystem.
• explain different bio-geochemical cycles like
the nitrogen cycle, oxygen cycle and carbon
Atomic mass, molecular mass and
cycle.
mole concept
Theory
Practical
5
I2
I
Key terms and terminologies of the unit
Ecology: Ecology can be defined as the study of the distribution and relations of organisms
and their interactions with the environment.
Wetland: A wetland is a place where land is permanently or seasonally covered with water.
Abiotic components: Abiotic components are the non-living components of an ecosystem.
Biotic components: Biotic components are all of the living organisms within an ecosystem.
Biogeochemical cycle: The biogeochemical cycle can be defined as a pathway by which a
chemical compound moves through the biotic and the abiotic components of an ecosystem.
Nitrogen fixation: The process of converting atmospheric nitrogen into organic nitrogen
compounds is called nitrogen fixation.
Biological fixation: Biological fixation is the process of conversion of atmospheric nitrogen
into nitrates by some symbiotic bacteria, free living soil bacteria and blue green algae.
Nitrogen assimilation: nitrogen assimilation is the formation of organic nitrogen compounds
like amino acids from inorganic nitrogen compounds present in the environment.
336
Optional Science - 10
BIOLOGY
Ammonification: The decomposition with production of ammonia or ammonium
compounds by the action of bacteria on nitrogenous organic matter is called ammonification.
Nitrification: The conversion of ammonia into nitrites (NO2 —)and then into nitrates (NO3—)
by the action of soil bacteria is called nitrification
Denitrification: Denitrification is the process of reduction of unused nitrates into free
nitrogen by the action of soil bacteria to return nitrogen back into the atmosphere.
Introduction
The word ecology is a combination of two different Greek words, oikos- house and logosstudy of. Therefore, Ecology can be defined as the study of the distribution and relations
of organisms and their interactions with the environment. According to Earnest Haeckel,
“ Ecology is the study of the reciprocal relationship between living organisms and their
environment.” In simple words, it is the scientific study of how living things interact with
each other and their natural environment. It includes the study of the population of plants and
animals as well as their communities and ecosystems.
Ecosystem is the interrelationship between living and non-living components in the
environment. It is the structural and functional unit of the environment. An ecosystem is
composed of organisms (biotic component), the communities they make up and non-living
components (abiotic components) of their environments. In this unit we will learn about
wetland ecosystem and some of the bio-geochemical cycles, namely carbon cycle, oxygen
cycle and nitrogen cycle.
Branches of Ecology
Autecology and Synecology are two main branches of ecology.
Autecology: Autecology is the study of an individual organism or its population throughout
their life in relation to their habitat in the environment. It is also known as
population ecology.
Syncecology: Syncecology is the branch of ecology that deals with the study of the connections
of group of organisms of different species which are associated together as a
unit in form of a community to their common environment.
Importance of ecology
1.
The study of ecology helps to conserve and protect nature and natural sources.
2.
It helps to understand the connections between plants and animals and their environment
and prevent the extinction of species.
3.
Ecology provides information about the benefits of ecosystems.
4.
It provides information for natural resource management.
Wetland ecosystem
A wetland is a place where land is permanently or seasonally covered with water. The water
can be fresh, salty or brackish. A common example of a wetland is the edge of a lake or ocean,
the delta at the mouth of a river, lowland areas that frequently flood. The main types of
wetlands are swamps (marshes, bogs and fens) and and sub-types include mangrove, carrum,
pocosin, and varzea.
BIOLOGY
Optional Science - 10
337
Eventhough the wetlands are important environmental assets, they occupy only 6% of the
earth's surface. Conservation of wetlands is important because they are the most productive
habitats of aquatic plants and animals, including mammals, birds, fish and invertebrates.
Wetlands are also a habitat for migratory birds and waterfowl, including ducks, egrets, and
geese.
Memory Plus
The largest wetlands in the world include the swamp forests of the Amazon and the Peat
lands of Siberia.
About 5% of the total surface area of Nepal is wetland area. In Nepal, Koshitappu,
Beeshazar lake and associated lakes, ghodaghodi lake area and Jagadishpur reser-voir
have been designated as wetland areas.
Importance of wetland ecosystem
Wetlands play a number of roles in the environment. The importance of wetlands is:
1.
Wetlands collect and hold flood water.
2.
Wetlands play a significant role in carbon sink and shoreline stability.
3.
Wetlands filter and clean water. They recharge groundwater aquifers.
4.
Wetlands serve as a home to a wide range of plants and animal life.
5.
Wetlands can improve tourism.
6.
Wetlands provide us with many products, such as fishes, sea salt, animal fodder, fuel
wood, medicinal herbs.
Fact with reason
Wetlands are valuable habitats for wildlife. Give reason.
Wetlands are valuable habitats for wildlife because the surrounding uplands of the
wetlands provide a home for a large number of species, including plants, mammals, birds,
amphibians, reptiles, fish and invertebrates. These animals use wetlands for food, water,
nesting grounds, breeding and for shelter.
Wetlands are important to protect against erosion, Give reason.
Wetlands protect against erosion because there are many plants and types of vegetation
found in the wetlands that help to stabilize the soil and are able to hold the soil in place
against erosive forces, such as waves and currents. Also, wetland plants trap sediments that
are found in the water, which helps to reinforce the soil against erosion.
Components of wetland ecosystem
The components of wetlands vary widely due to local and regional differences in topography,
hydrology, vegetation and human involvement. The components of a wetland ecosystem can
be divided into two factors: Biotic and abiotic.
Abiotic components
Abiotic components are the non-living components of an ecosystem. These components are:
Water, soil, factors climate and temperature, rainfall.
0
338
Optional Science - 10
BIOLOGY
1.
Water: The wetlands contain surface water and ground water in its reservoirs. It is also
associated with streams, lakes and reservoirs as water sources. Most of the wetlands
have high concentration of dissolved nutrients and mineral ions, except bogs. Bogs
receive their water from the atmosphere, therefore have low mineral ion composition.
2.
Soil: Most nutrients like calcium, phosphorus, sulfur and nitrogen are found in the soil
of wetlands. Carbon is the major nutrient.
3.
Climate and temperature: The temperature of the wetlands varies greatly,depending
on the location of the wetland. Many of the world’s wetlands are in temperate zones.
Therefore, summers are warm and winters are cold, but the temperature is not extreme.
The wetlands found in the tropic zones are warm throughout the year.
4.
Rainfall: The amount of rainfall also varies widely according to the area. Wetlands in
southeast Asia receive heavy rainfall. The wetlands of the northern areas of North
America receive little rainfall.
Biotic Components
fig: Wetland ecosystem
Biotic components are all of the living organisms within an ecosystem. In wetland ecosystem
,biotic components are the flora (plants) and fauna (animals).
Plants found in wetlands (flora)
Submerged plants, floating plants, emergent plants and aquatic trees are the four main
groups of hydrophytes found in the wetlands.
a. Algae: Algae are photosynthetic, non-vascular thalloid aquatic plants. They are
usually covered with mucilage that protects them form drying and decaying. They
are food sources for some animals, fish and invertebrates. Algae found in wetlands
are planktons. These are microscopic aquatic plants (algae). These are the primary
producers. They are filamentous algae, Chara and Nitulla.
BIOLOGY
Optional Science - 10
339
b. Submerged plants can grow in saline and fresh water. These plants are a source
of food for many animals. They help in the filtration of water within the wetlands.
Examples: hydrilla, sea grasses and eel grass.
c. Floating plants float freely on the surface of water. Example: green-algae, duckweed,
wolfia, water hyacinth, pistia.
d. Emergent plants have roots that are fixed in the mud at the bottom of the wetlands.
The stems are hollow and have plate-like leaves that float on the surface of water.
Example: water-lily, lotus, etc.
Some shrubs or small trees are also found in forested wetlands. They have a woody
stem and can grow 20 feet tall. Example: buttonbush and alder.
Animals found in wetlands (fauna)
Many species of frogs, different kinds of reptiles like turtles, alligators, crocodiles,
snakes, lizards and fishes are found in the wetlands. Among them, fishes are more
dependent on the wetland ecosystem to survive. Amphibians reproduce and feed on
the wetlands. Snapping turtles are one of the many kinds of turtles found in wetlands.
Tadpoles control the algal population and adult frogs feed on insects. The mammals
found in the wetlands include the beaver, swamp rabbit, Florida panther. Different
species of insects and invertebrates can be seen throughout the wetlands.
Memory Plus
A patch of land that develops pools of water after a rain is not considered a wetland.
Wetlands are characterized as having a water table that stands at or near the land
surface for a long period each year to support aquatic plants.
Biogeochemical cycle
Many elements cycle through an ecosystem, organisms, air, water and soil. They are passed
from one form to another and from one part of the biosphere to another through cycles known
as the biogeochemical cycle. Thus, the biogeochemical cycle can be defined as a pathway by
which a chemical compound moves through the biotic and the abiotic components of an
ecosystem. The cycle involves a biological, geological and chemical process. A biogeochemical
cycle connects living things to the earth. There are four chemicals that make up 95 % of living
things. They are carbon, oxygen, hydrogen and nitrogen. These chemicals are constantly being
cycled through living and non-living matter.
Importance of biogeochemical cycle
1.
The biogeochemical cycle enables the transformation of matter from one form to another
for its utilisation. For example: We utilize water in liquid form, though water is also
found in vapor form or solid form as ice.
2.
The biogeochemical cycle enables the transfer of chemical molecules from one locality
to another. For example: Nitrogen from the atmosphere is transported to the soil in
nitrate form.
3.
The biogeochemical cycle helps in the storage of elements in natural reservoirs and are
released to organisms in small consumable amounts.
4.
The biogeochemical cycle helps to balance the ecosystem by recycling the chemical
elements.
340
Optional Science - 10
BIOLOGY
Types of biogeochemical cycle
The biogeochemical cycle are classified into three types. They are water cycle, gaseous cycle
and sedimentary cycle(mineral cycle).
1.
Water cycle: It involves the movement of water across various spheres of the earth
through different processes such as precipitation, evaporation, sublimation, condensation,
snowmelt and infiltration. The water cycle is also termed as hydrological cycle.
2.
Gaseous cycle: It includes the continuous circulation of carbon, nitrogen, oxygen and
hydrogen gases in the atmosphere of the earth.
3.
Sedimentary cycle: It includes the cycling of minerals like iron, calcium, phosphorous,
sulfur that are essential nutrients for living organisms. The sedimentary cycle is also
known as mineral cycle.
In this unit we will learn about gaseous cycles (carbon cycle, oxygen cycle and nitrogen cycle).
Carbon cycle
Carbon dio xide in
/ ;
<he a<mosphm
Animal
~--/----, (I ~~
:l~.~,
Fossil fuel
com bustion
Plant
respi ratio n
carbon compo unds I -W--- - - -- i
in d ead organic
m atte r
O rganic
compo unds
in animals
Pho tosyn thesis
Death
Foss1hzat1o n
~
I
\
O rganic com po un ds
m green pla nts
fig: Carbon cycle
Carbon is the main component of living things. The main source of carbon is carbon dioxide.
Carbonates derived from rocks, volcanic eruption, fossil fuels like coal and petroleum products
give rise to carbon dioxide in the earth’s atmosphere.
The main process that brings carbon from the atmosphere to the biosphere is photosynthesis,
where producers utilize atmospheric carbon dioxide and convert it into carbon compounds.
Carbon dioxide is released back to the environment by the process of respiration, decomposition
of organic wastes and dead bodies, burning of wood and fossil fuels, volcanic eruption and
weathering of carbonate rocks.
The carbon cycle takes place by various processes:
1.
Photosynthesis: The first step in the carbon cycle is the conversion of inorganic
atmospheric carbon into biological form. Producers absorb the atmospheric carbon as
carbondioxide by the process called photosynthesis. In photosynthesis, carbondioxide
combines with water in the presence of sunlight to make carbohydrates.
2.
Respiration and combustion: Animals feed on plants passing carbon compounds along
the food chain. The carbondioxide is exhaled during respiration.
BIOLOGY
Optional Science - 10
341
Carbondioxide is also released in the atmosphere by burning fuels like coal, log and
petroleum products. Volcanic eruption and weathering of carbonate rocks by chemicals
also release carbondioxide in the atmosphere.
3.
Decomposition: When plants and animals die, the dead organisms are eaten by the
decomposers. The carbon in their bodies is returned to the atmosphere as carbondioxide.
If decomposition is not completed, the remaining materials may then be available as
fossil fuel in the future for combustion.
Memory Plus
Since carbondioxide is a primary greenhouse gas, many studies argue that increase in
atmospheric carbondioxide from human activities has increased the greenhouse effect.
This can change our global climate, resulting in higher global temperatures.
The carbon cycle is mainly balanced by the process of photosynthesis and respiration.
Oxygen Cycle
: Ulrav+ O, -Oro••l•Jor(O.,J
O t+ UV
01+0
n•v~_0_+_0__
=
i
i
Plants, Animals &
Decomoosers
.s Fuels
'---- ~
I Green Planls
fig: Oxygen cycle
All living things need oxygen to survive. It is necessary for respiration. Living cells need
oxygen to create energy. Plants take in oxygen and give out carbondioxide for synthesis during
the process of photosynthesis. We take in oxygen to break carbohydrates into energy and give
out carbondioxide by the process of respiration. The oxygen cycle helps in the movement of
oxygen in the three main regions of the earth: atmosphere, biosphere and lithosphere.
Steps in Oxygen Cycle
1.
In the atmosphere, the energy in the sunlight breaks the oxygen molecule to produce
free oxygen. This process is called photolysis.
2.
In the biosphere, plants and animals use oxygen for respiration and return it to the air
and water as carbondioxide. Plants use this carbondioxide in the presence of sunlight
to form carbohydrates and water. This process is called photosynthesis. In this process,
oxygen is produced as a byproduct. Water is the main source of oxygen.
3.
In the lithosphere, oxygen is fixed in minerals like silicates and oxides. When the
mineral bearing oxygen is exposed to chemical reaction, the minerals wear down, and
free oxygen is produced. This process is called chemical weathering.
342
Optional Science - 10
BIOLOGY
Nitrogen cycle
Atmospheric
~ itrogeo
L.
lenin
(l<: gas)
Physical fixation
lnduslrialfintion
Bk>l02ical fi:ution
Plants
Ammonia liquor
Nitrates in soil
~ ilric a dd in soil
~ itrificatk>n
fig: Nitrogen cycle
Nitrogen is the most abundant element in the atmosphere. There is about 78% of nitrogen in
the air. It is essential for the formation of amino acids in proteins. It is also the building block
of nucleic acids (DNA and RNA). As nitrogen is not so reactive, it cannot be used directly by
plants to make proteins. Nitrogen is converted into various forms that can be utilized by living
organisms. Such forms of nitrogen are organic nitrogen, ammonium salt, nigrous oxide, nitrate,
nitrate, nitric oxide, etc.
The nitrogen cycle is a complex biogeochemical cycle. It completes in five stages: nitrogen
fixatation, nitrogen assimilation, ammonification, nitrification and denitrification.
1.
Nitrogen fixation: The process of converting atmospheric nitrogen into organic nitrogen
compounds is called nitrogen fixation. It occurs in three ways:
a. Biological fixation of nitrogen
b. Atmospheric fixation of nitrogen
c. Industrial fixation of nitrogen
a.
Biological fixation of nitrogen
Most atmospheric nitrogen is fixed through biological processes. Biological fixation
is the process of conversion of atmospheric nitrogen into nitrates by some symbiotic
bacteria, free living soil bacteria and blue green algae. The symbiotic bacteria host on
the root nodules of leguminous plants. The bacteria which convert atmospheric nitrogen
into nitrates are called nitrogen fixing bacteria. For example: free-living nitrogen fixing
bacteria(azotobacter, clostridium), symbiotic bacteria (rhizobium), cyanobacteria (bluegreen algae), etc. Algae like nostoc can also fix atmospheric nitrogen.
b.
Atmospheric fixation of nitrogen
Nitrogen fixation also occurs by the physical or non-biological process. A small amount
of nitrogen is converted into ammonia and nitrates by the energy produced during
lightning in the air. When lightning occurs, atmospheric nitrogen reacts with oxygen
in the air and form nitric oxide and nitrogen dioxide. These oxides combine with water
vapor to form nitrous or nitric acids. These acids then combine with salts and produce
nitrate ions.
BIOLOGY
Optional Science - 10
0
343
c.
N2 + O2 2NO
2NO+ O2 2NO2
NO2 + O2
N2O5
N2O5 + H2O
2HNO3
HNO3 + CaCO3
Ca(NO3)2 + CO2 + H2O
Industrial fixation of nitrogen
In industrial fixation, nitrogen is made to combine with hydrogen to form ammonia
by Haber process. The ammonia thus formed is converted into nitrate to use as a
nitrogenous fertilizer.
(200-600) atm., 500oC
N2 + 3H2 Fe/Mo
2.
2NH3
Nitrogen assimilation
Plants absorb nitrates from the soil and use them to build up proteins. These plants are
eaten by herbivores and get the nitrogen containing nutrients. Again the carnivores eat
these herbivores and get animal proteins. Thus, nitrogen assimilation is the formation
of organic nitrogen compounds like amino acids from inorganic nitrogen compounds
present in the environment.
3.
Ammonification
Some of the plant protein and animal protein are utilized by the individual organisms.
Animals excrete the unused nitrogen compounds in the soil. The remains of plants and
animals and their waste products are decomposed by the microorganism in the soil
to produce ammonia. This ammonia is dissolved in the soil in the form of ammonium
ions. The decomposition with production of ammonia or ammonium compounds by
the action of bacteria on nitrogenous organic matter is called ammonification. The
bacteria that cause ammonification are Bacillus, Proteus, Clostridium, Pseudomonas,
Streptomyces etc.
4.
Nitrification
The conversion of ammonia into nitrites (NO2—) and then into nitrates (NO3—) by the
action of soil bacteria is called nitrification. These bacteria are called nitrifying bacteria.
For example, Nitrosomonas, Nitrobacter, Nitrosococcus, etc. are nitrifying bacteria. In
a more specific way, the bacteria that oxidizes ammonia into nitrites are called 'nitrite
bacteria' and that oxidize nitrites into nitrates are called 'nitrate bacteria'.
0
344
Nitrosomonas
2NH3 + 3O2 2HNO2 + 2H2O
Nitrosomonas
2HNO3 + O2 2HNO3
Optional Science - 10
BIOLOGY
5.
Denitrification
Denitrification is the process of reduction of unused nitrates into free nitrogen by the
action of soil bacteria to return nitrogen back into the atmosphere. Bacteria involved
in denitrification are called denitrifying bacteria. For example, Agrobacterium,
micrococcus denitrificans, pseudomonas, bacillus, etc. are some denitrifying bacteria.
Denitrification completes the nitrogen cycle.
Answer writing skill
1.
Define ecology.
Ecology can be defined as the study of the distribution and relations of organisms and
their interactions with the environment.
2.
What is ammonification?
When plants and animals die, the microorganisms present in the soil or air breaks
down the organic matter of the dead bodies into ammonia. This process is called
ammonification.
3.
Give the name of some nitifying bacteria.
Nitrosomonas, nitrobacter, nitrosococcus are some nitrifying bacteria.
4.
Write the components of the wetland ecosystem.
The components of a wetland ecosystem can be divided into two factors:
Biotic components: animals like reptiles, amphibians, aquatic plants and algae, and
Abiotic components: Water, soil, temperature, rainfall
5.
Write some common examples of wetlands.
Common examples of wetlands are the edge of a lake or ocean, the delta at the mouth
of a river, low land areas that frequently flood.
6.
Write short notes on nitrogen fixation.
The process of converting atmospheric nitrogen into organic nitrogen compounds is
called nitrogen fixation. Atmospheric nitrogen is fixed through biological and nonbiological (physical) processes. Atmospheric nitrogen is deposited in the soil mainly
through precipitation. Then the nitrogen fixing bacteria and blue green algae in the soil
converts it into ammonia. Bacteria like azotobacter, clostridium, rhizobium, nostoc are
present in the root nodules of leguminous plants and loosely dug soil.
When lightning occurs, atmospheric nitrogen reacts with oxygen in the air and form
nitric oxide and nitrogen dioxide. These oxides combine with water vapou to form
nitrous or nitric acids. These acids then combine with salts and produce nitrate ions.
BIOLOGY
Optional Science - 10
0
345
7.
N2 + O2 2NO
2NO+ O2 2NO2
NO2 + O2
N2O5
N2O5 + H2O
2HNO3
HNO3 + CaCO3
Ca(NO3)2 + CO2 + H2O
What are the important sources of carbon?
The main source of carbon is carbon dioxide. Other sources of carbon are rocks, volcanic
eruption, fossil fuels like coal and petroleum products that gives rise to carbon dioxide
in the earth’s atmosphere.
8.
How does the study of ecology help to conserve natural resources?
The study of ecology helps to conserve natural resources by:
9.
i.
Providing information about the benefits of ecosystems.
ii.
Providing information for natural resource management.
iii.
Providing information about the different types of natural sources.
Why is conservation of wetlands important?
Conservation of wetlands is important because they are the most productive habitats of
aquatic plants and animals, including mammals, birds, fishes and invertebrates.
10.
Explain the steps involved in the oxygen cycle.
Photolysis: In the atmosphere, the energy in the sunlight breaks the oxygen molecule to
produce free oxygen. This process is called photolysis.
0
346
1.
Photosynthesis: In the biosphere, plants use this carbondioxide in the presence of
sunlight to form carbohydrates and water. This process is called photosynthesis. In
this process, oxygen is produced as a byproduct.
2.
Chemical weathering: In the lithosphere, oxygen is fixed in minerals like silicates
and oxides. When the mineral bearing oxygen is exposed to chemical reaction, the
minerals wears down, and free oxygen is produced. This process is called chemical
weathering.
Optional Science - 10
BIOLOGY
Exercise
Section "A"
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
Define ecology.
What is a wetland?
Define biogeochemical cycle.
What are the types of biogeochemical cycle found in atmosphere?
What is the main source of carbon?
Write any two main sources of oxygen.
What is nitrogen fixation?
What is nitrogen assimilation?
What is ammonification?
Name any two ammonifying bacteria.
What is nitrification?
Give name of two nitrogen fixing bacteria.
What is denitrification?
What are denitrifying bacteria?
Give the name of two denitrifying bacteria.
Section "B"
1.
2.
3.
4.
5.
List the biotic and abiotic components of wetland ecosystem.
Give the names of the main type of biogeochemical cycle.
Explain the importance of the biogeochemical cycle.
Differentiate between gaseous cycle and sedimentary cycle.
Write the difference between nitrification and denitrification process of the nitrogen
cycle.
Section "C"
1.
2.
3.
4.
5.
Mention the importance of ecology.
Differentiate between autecology and syncecology.
Write the importance of algae in wetland ecosystem.
Why is a wetland ecosystem important?
Why is carbon cycle important?
BIOLOGY
Optional Science - 10
347
Section "D"
1.
2.
3.
4.
5.
Describe the abiotic components of a wetland ecosystem in brief.
What are the biotic components of a wetland ecosystem? Explain.
Describe the carbon cycle in brief.
Give a short account of the nitrogen cycle.
Describe the oxygen cycle in brief.
Multiple choice questions
1.
The water in a wetland can be
a) Fresh
b) Salty
c) Brackish
d) All of the
above
Hydrilla is an example of
a. Submerged plants b. Floating plants
c. Emergent plants
d.Terrestrial plants
Rhizobium is an example of
a. Nitrifying bacteria
b. Nitrogen fixating bacteria
c. Denitrifying bacteria
d. Ammonification bacteria
The process of converting atmospheric nitrogen into organic nitrogen compounds.
a. nitrogen fixation
b. nitrification
c. ammonification
d. denitrification
Example ofdenitrifying bacteria is
a. Rhizobium
b. Nitrosomonas
c. Micrococcus denitrificans
d. Nitrobacter
The main source of oxygen is
a. Water
b. Soil
c. Minerals
d. Air
There is about ……. of nitrogen in the air.
a. 78%
b. 72%
c. 71%
d. 74%
Water cycle is also known as
a. Sedimentary cycle
b. Hydrologic cycle
c. Gaseous cycle
d. Liquid cycle
2.
3.
4.
5.
6.
7.
8.
Project Work
1.
Study the wetlands found in Nepal. Prepare a report on any one of the wetlands and
show it to your teacher.
In your report include the abiotic factors and biotic factors of that wetland.
2.
348
On a chart paper, present any one of the biogeochemical cycles and display it in
your classroom.
Optional Science - 10
BIOLOGY
UNIT
18
BEHAVIORAL
BIOLOGY
Karl Landsteriner (1868-1943) He was an Austrian biologist, physician and immunologist.
He developed the modern system of classification of blood groups from his identification
of the presence of agglutinins in the blood and identified the Rhesus factor in 1937.
He discovered the polio virus in 1909, and for this he was awarded the Nobel Prize in
Physiology, or Medicine. He is also known as the “father of transfusion medicine”.
Syllabus issued by CDC
Learning objectives:
At the end of this unit, the students will be able to:
• define organ transplantation.
I • explain the method of organ transplantation.
Atomic mass, molecular mass and • state the effects and control measures for high
mole concept
blood pressure, high cholesterol and high uric
acid.
• define and explain antibiotics.
• explain the method to distinguish blood
group.
Theory
Practical
6
I2
Key terms and terminologies of the unit
Organ transplantation: An organ transplantation is the process of transferring an organ
from the body of donor to the body of recipient, to replace a damaged or missing organ
Transplant or graft: The tissue or organ which gets transplanted is called a transplant or
graft.
Blood pressure: Blood pressure is the pressure exerted on the walls of the arteries as blood
flows through them.
Systolic blood pressure: Systolic blood pressure is the pressure in the arteries as the
ventricles of the heart contract.
Diastolic blood pressure: Diastolic blood pressure is the pressure in the arteries as the
ventricles of the heart relax.
BIOLOGY
Optional Science - 10
349
Cholesterol: Cholesterol is an oil based substance (lipid) that does not mix with blood and
distributed throughout the body.
Uric acid: Uric acid is a waste product obtained during the breakdown of purines found in
foods such as liver, mushrooms, dried beans, etc.
Gout: Urate crystals when accumulate around the joints and soft tissues to cause
inflammation and pain. This is known as gout.
Antibiotic: Antibiotic is defined as a chemical substance produced by some microorganisms
that have the capacity to deactivate or kill other microorganisms
Blood group: A blood group is a classification of blood based on the presence or absence of
antigens on the surface of red blood cells (RBCs) and antibodies in blood plasma
Rh factor: Rh factor is the protein known as RhD antigen that is present on the surface of
RBC
Introduction
Biology is the science of life and of living organisms. It includes numerous fields like botany,
zoology, mycology, microbiology, biochemistry, etc. The practical uses of biological knowledge
come under applied biology. Applied Biology is the application of knowledge of Biology in
development of tools and methods specific to biological research needs. It is important for the
technologies and applications relevant to biology-based industries and institutions. In this
unit we will learn about organ transplantation, blood studies-blood group and its grouping,
cholesterol, high blood pressure, hypertension, uric acid. We will also learn about antibiotics
that destroy or inhibit the growth of microorganisms.
Organ Transplantation
Some damaged organs in the body can be replaced by transplantation. There are many
examples of tissue or organ transplantation on human beings such as skin grafting, heart
transplantation, kidney transplantation etc. Organs that can be transplanted include bone
marrow, lungs, heart, liver, cornea and kidneys. The person who receives the organ is the
recipient, and the person from whose body the organ was taken is the donor.
An organ transplantation is the process of transferring an organ from the body of donor to the
body of recipient, to replace a damaged or missing organ. It involves the removal of damaged
or injured tissues or organs from the body of receipient and replacing them by similar
tissues/organs from the body of donor. The tissue or organ which gets transplanted is called
a transplant or graft. It is essential to perform tissue matching and blood group matching
tests before undertaking any graft/ transplant. Transplantation may result in the rejection of
transplanted organs due to production of antibodies by patient’s immune system against the
transplanted organ. Therefore, the success rate of an organ transplant is very low. Organs
that have been successfully transplanted include the heart, kidneys, liver, lungs, pancreas,
intestine, and thymus. Some organs, like the brain, cannot be transplanted.
Memory Plus
The world’s first successful organ transplant was a kidney transplantation in 1954. It was
undertaken by David Hume and Joseph Kelly at the Peter Brigham Hospital in Boston.
350
Optional Science - 10
BIOLOGY
Types of organ transplantation
On the basis of the genetic relationship between the
donor and recipient, transplantation is classified
into four types: autograft, isograft, allograft
(homograft) and xenograft (heterograft).
1.
Autograft: In autograft, the donor and
recipient is the same individual. In this
transplantation, one’s own tissue from a
part of the body is transplanted to another
part of the body. A common example of
this transplantation is skin graft for plastic
surgery. The success rate is high for this
type of transplantation.
!lsogratt !
-(8«1ticalTwin$ I
fig: Types of organ transplantation
2.
Isograft: In isograft, the donor and recipient are genetically identical individuals, i.e.
identical twins. Example: kidney transplantation
3.
Allograft (Homograft): In allograft, the donor and recipient are genetically different
but are of the same species. Example: Skin transplantation and blood transplantation
from others.
4.
Xenograft or heterograft: In xenograft, the donor and recipient are of different species,
i.e. from a monkey to a human or from a pig to a human. This is a special case of
transplantation carried for research and experiment. Examples: transplantation of
baboon livers into humans.
Advantage of organ transplantation
1. It can be carried out to save life of a person dying of organ failure.
2. It helps in replacing a non-functional, damaged or lost body part with functional ones.
Disadvantages of organ transplantation
1. The main disadvantage is the rejection of the transplanted organ by the patient’s body
due to production of antibodies by the patient’s immune system against the transplanted
organ. Patients may die due to allergies or reaction from the new transplanted organ.
3.
Organ transplantation is very expensive. It may not be affordable for the real people in
need.
Prevention of graft rejection
Sometimes, the body does not accept the transplanted organ. The immune system recognizes
the donor organ as a foreign organ and attacks it, resulting in transplant failure. In such a case,
there is a need to remove the organ immediately from the recipient, which is called rejection.
The graft rejection can be prevented by the following measures:
1. Selection of organs from a genetically similar member.
2.
Suppressing the immune system by radiation.
3.
Performing tissue typing and blood grouping test.
4.
Use of immune-suppressant drugs.
5.
Use of monoclonal antibodies.
BIOLOGY
Optional Science - 10
351
Memory Plus
Many organs and tissues are donated by individuals at the time of their death. Others are
donated by living donors. Generally, donated organs are matched with individuals on an
organ-waiting list. Matching is based on a variety of factors, including blood and tissue
type, medical need, length of time on the waiting list and weight of donor and recipient.
High blood pressure
Our heart pumps blood around the body constantly every second of our lives. The pumping
of blood creates pressure, and we call that blood pressure. Blood pressure is the pressure
exerted on the walls of the arteries as blood flows through them. Blood pressure is of two
types: systolic blood pressure and diastolic pressure. Systolic blood pressure is the pressure
in the arteries as the ventricles of the heart contract. Diastolic blood pressure is the pressure
in the arteries as the ventricles of the heart relax. Our normal blood pressure is below120/ 80
and above 100/60. Here, the numerator value indicates the systolic blood pressure and the
denominator indicates diastolic blood pressure. Anyone whose blood pressure is more than
140/ 90mmHg for a sustained period of time is said to have high blood pressure. High blood
pressure is also termed as hypertension.
Memory Plus
Sphygmomanometer measures blood pressure. In order to measure blood pressure there
is use of Stethoscope along with Sphygmomanometer.
The arterial blood pressure is always written in systolic pressure by diastolic pressure in
mm of Hg form (e.g. 120/80 mmHg).
Symptoms of high blood pressure
Most of the people with high blood pressure will not experience any symptoms until it reaches
about 180/110 mmHg. The most common symptoms of high blood pressure are:
1. Headache lasting for several days
2.
Nausea and dizziness
3.
Vomiting
4.
Blurred or double vision
5.
Nose bleeding (epistaxis)
6.
Sensation of irregular or forceful beating of the heart (palpitation)
7.
Breathlessness or shortness of breath (dyspnea)
Causes of high blood pressure
There is no identifiable cause of high blood pressure, but there are some risk factors that may
cause high blood pressure.
1.
Age - everyone is at a greater risk of high blood pressure as they get older. Prevalence of
hypertension is higher in people above 60 years of age.
352
Optional Science - 10
BIOLOGY
2.
Family history: if we have close members with hypertension in the family, there are high
chances of developing hypertension.
3.
Ethnic background (race): Research has indicated that people with African or south Asian
ancestry have a higher risk of developing hypertension compared to American people.
4.
Body size: Being both overweight and obese is a key risk factor for hypertension.
5.
Gender: In general, men are more prone to hypertension than females. But generally, men
are prone to hypertension at a younger age and women have a higher rate of hypertension
in older age.
6.
Lifestyle of an individual: lack of exercise, greater intake of dietary salt, high fat diet and
excessive intake of alcohol and smoking contribute to increased risk of hypertension.
7.
Mental stress: various studies have said that people with mental stress over a long period
of time is at higher risk of hypertension.
Effects of high blood pressure
If high blood pressure is not treated or controlled, the excessive pressure on the artery walls
can lead to damage of the blood vessels as well as vital organs. Some of the effects of high
blood pressure are:
1.
Stroke: blood flow to the brain is impaired by blockage and rupture of an artery to the
brain, and the brain cells die, causing a stroke. It may lead to death.
2.
Heart attack: due to the loss of blood supply, the heart muscle dies.
3.
Heart failure: pumping blood with high
pressure into the blood vessels, the heart muscle
thickens and fails to work.
4.
Blood clot: some blood converts into solid state
due to high blood pressure and causes serious
complications.
5.
Kidney disease: high blood pressure damages
the small blood vessels in the kidneys, due to
this they cannot function properly.
6.
Eye disease (hypertensive retinopathy): If high
blood pressure is not treated in time, the blood
vessels in the eyes may tear or get thickened,
which can lead to vision loss.
Bleeding withi.n the brain
(hemorrhagic stroke) , /
Loss of sight from
narrowing, closure.
or bleeding of
small vessels
in the retina
:-..
/
fig: Effects of high blood pressure
Control measures of high blood pressure
1.
Lowering the intake of dietary salt: modest blood pressure reductions can be achieved by
lowering the amount of salt intake by people with hypertension.
2.
Regular physical exercise: people suffering from hypertension should engage in at least
30 minutes of moderate physical exercise, such as walking, jogging, cycling or swimming.
3.
Reducing weight and maintaining it: As we know, hypertension is closely related to
body weight, so it is important to maintain normal weight. Reduction in weight leads to
fall in blood pressure.
BIOLOGY
Optional Science - 10
353
4.
Increasing the consumption of vegetables and fruits: people suffering from hypertension
or at risk of hypertension should eat whole grain, high fibre foods, more vegetables and
fruits to minimize the effects of high blood pressure.
5.
Moderation of alcohol consumption: excessive drinking is associated to raise the blood
pressure with a high risk of stroke. People with hypertension or at risk of hypertension
should lower the alcohol consumptions.
6.
Decreasing the consumptions of dietary fat: People with hypertension or at risk of
hypertension should minimize the intake of saturated and total fat.
7.
Stress reduction: Avoiding sources of stress and developing healthy lifestyles can manage
stress that can help to control blood pressure.
8.
Quitting smoking: Smoking also raises blood pressure and has adverse effect on health.
Therefore, People with hypertension or at risk of hypertension are highly recommended
to give up smoking.
Fact with reason
Patients with high blood pressure should not eat food with high amounts of salt, why?
Patients with high blood pressure should not eat food with high amounts of salt because
too much salt in our diet makes our body hold on to more water, which raises your blood
pressure and puts strain on our heart and kidneys.
Activity
Measure the blood pressure of all the students present in your classroom Fill the data in a
table. Make a comparative study of blood pressure on the basis of gender.
High cholesterol
Cholesterol is an oil based substance (lipid) that does not mix with blood and distributed
throughout the body. It is carried to different parts of the body through blood by lipoproteins.
Cholesterol is both beneficial and harmful to us. At normal level, it is an essential substance
for the body. But, if its concentration in the blood gets too high, it is dangerous for the heart
and health. It is found in every cell of the body and has important natural functions. It helps in
digesting food, producing hormones , generating vitamin D. It is manufactured by our body
and also taken from food.
Fact with reason
High cholesterol can cause heart attacks and strokes. Give reason.
If the cholesterol level in our blood gets too high, it starts to deposite in the walls of our arteries.
This is called hardening of the arteries (artherosclerosis). This can narrow the arteries and makes
it harder for blood to flow through them, leading to dangerous blood clots and inflammation
that can cause heart attacks and strokes.
0
354
Optional Science - 10
BIOLOGY
Types of Lipoproteins that carry Cholesterol
There are two types of lipoproteins that carry cholesterol:
1.
Low density lipoprotein (LDL): It transports cholesterol around the body where it is
needed. The cholesterol carried by this type of lipoprotein is termed as bad cholesterol. If
the level of cholesterol is too much, it may get deposited in the arteries and raise the risk
of heart attack and stroke.
2.
High density lipoprotein (HDL): It carries away excess cholesterol from our cells and
tissues and returns it to our liver. This cholesterol is reused whenever needed by our
body. The cholesterol carried by this type of lipoprotein is termed as 'good cholesterol'.
Memory Plus
Increase in the level of LDL leads to deposition of cholesterol in the arteries, whereas
HDL carries cholesterol to the liver for removal from the body.
Fact with reason
Low density lipoprotein (LDL) cholesterol is known as 'bad cholesterol', why?
Low density lipoprotein (LDL) cholesterol is known as 'bad cholesterol' because having
high levels of LDL can lead to plaque buildup in our arteries and result in heart disease
and stroke.
High density lipoprotein (HDL) cholesterol is known as 'good cholesterol', why?
High density lipoprotein (HDL) cholesterol is known 'good cholesterol' as the lipoprotein
absorbs this cholesterol and carries it back to the liver, which flushes it from the body.
Causes of high cholesterol
1.
The primary cause of high cholesterol is genetic. It starts to rise after the age of 20.
2.
Being overweight or obese can also lead to higher blood LDL levels.
3.
Other conditions like diabetes, liver or kidney disease, etc. also raise the level of cholesterol.
4.
Pregnancy and underactive thyroid gland also increase the cholesterol level.
5.
Some drugs like progestins, anabolic steroids and corticosteroids also increase LDL
cholesterol and decrease HDL cholesterol.
Effects
1.
Deposition of cholesterol in the arteries narrows it. This condition is termed as
atherosclerosis. In this case, plaques form in arteries and cause restriction of blood flow.
2.
High cholesterol is a major risk factor for coronary heart disease(CHD) like heart attacks
and stroke.
3.
It causes pain and discomfort in the chest.
4.
High cholesterol can create problem with blood flow to the legs, causing numbness.
5.
High cholesterol can cause bile imbalance that leads to formation of gall stones.
BIOLOGY
Optional Science - 10
355
Control measures of high cholesterol
In order to manage high cholesterol levels to reduce the risk of coronary heart disease and
heart attacks, some changes in the lifestyles of a person are recommended.
1. Limiting intake of fat in the diet helps to manage the cholesterol level.
2. Eating vegetables, fruits and fiber-rich whole grains also helps to lower the risk of high
cholesterol.
3. Regular exercise also helps to maintain the cholesterol level.
4. Avoiding smoking
5. Achieving and maintaining a healthy weight.
Memory Plus
Having high cholesterol levels does not show any signs or symptoms. Unless routinely
screened through regular blood testing, high cholesterol levels will go unnoticed and
could present a silent threat of heart attack or stroke.
Uric acid
Uric acid is a waste product obtained during the breakdown of purines found in foods such
as liver, mushrooms, dried beans, etc. kidneys filter uric acid from blood and passes out of
the body in urine. A small amount passes out of the body in stool. However, if the kidney
fails to function at the appropriate level, or if uric acid intake is too high to be balanced by
kidney excretion then the level of uric acid in the blood increases. This condition is known as
hyperuricemia.
Normal uric acid levels are 2.4-6.0 mg/dL (female) and 3.4-7.0 mg/dL (male). The high
concentration of uric acid in the blood is converted into urate crystals. These urate crystals then
accumulate around the joints and soft tissues to cause inflammation and pain. This is known
as gout. Gout is the most common form of inflammatory arthritis, called gouty arthritis. It is
caused by the high uric acid level in blood. These crystals accumulate in the joints and bring
about a gout flare-ups. Gout is most commonly seen in men between the ages of 40 and 50.
Symptoms of Gout
Gout has painful and distinctive symptoms during flare-ups. The common symptoms of gout are:
1. There is intense joint pain. The pain is most severe in the first 12 to 24 hours.
2. Joint pains spread to more joints over a week.
3
Redness, tenderness and swelling of the joints
Effects of Hyperuricemia
Gout affects the ankles, heels and toes. The painful gout flare is concentrated in the joints.
Following are the effects of hyperuricemia:
1. Patient suffers a low fever of 99oF to 100ᵒF.
2. Patients suffering from gout experience swelling and pain in the ankles, knees, feet, wrist
or elbows.
2. Chronic gout reduces the function of the kidney. It may result in the formation of kidney
stones.
3. If gout is untreated, it can cause deposition of large lumps of urate crystal at joints and
results in permanent damage to the joints.
356
Optional Science - 10
BIOLOGY
Causes of gout
There are several factors that can make a person more susceptible to gout. Following are the
major causes of the high levels of uric acid that lead to gout:
1.
Diet rich in purines: Purines are broken down by our body into uric acid. Foods that
contain high levels of purines include nuts, organ foods such as liver, kidney, etc.
2.
High production of uric acid: This can happen in certain inherited genetic metabolic
disorders, leukaemia and during chemotherapy for cancer.
3.
Less filtration of uric acid by the kidneys: This can be caused by kidney disease,
starvation and alcohol use. This also can occur in people taking medications.
4.
Obesity or sudden weight gain: In case of the obese people, the body’s tissues break
down more purines. This can cause high uric acid level in blood.
Control measures of gout
1.
Doing regular exercise.
2.
Eating fresh fruits (e.g. cherries) and vegetables.
3.
Avoiding high purine foods, such as dried beans and peas, mushrooms, organ meats
(liver and kidneys), asparagus, etc.
4.
Consuming baking soda increases the alkalinity of the blood and lower the amount of
uric acid.
5.
Patients are advised to drink more water.
6.
Limiting alcohol intake, especially beer.
7.
Maintain normal weight in case of obesity.
Fact with reason
Gout patients should avoid foods that are rich in purines, why?
Gout patients should avoid foods that are rich in purines like meat and fish as they increase
the amount of uric acid in a person’s blood, which can worsen the symptoms of gout. So,
gout patients should eat food with low protein content.
Antibiotic
Antibiotic is a combination of two Greek words: anti- against and bios- life. Therefore,
antibiotic is defined as a chemical substance produced by some microorganisms that have
the capacity to deactivate or kill other microorganisms. They are widely used in the field of
medicine to cure a number of diseases, especially bacterial infections. The antibiotics are very
reactive even in very low concentration.
Memory Plus
The first antibiotic was penicillin, which was discovered in 1929 by Alexander Fleming
from a mold culture.
Antibiotics are not effective against the viral diseases such as common cold or influenza.
BIOLOGY
Optional Science - 10
357
Types of antibiotics
On the basis of the action of antibiotics towards the pathogens, antibiotics are of two types:
1.
Bactericidal antibiotics: Bactericidal antibiotics kill bacteria directly. The suffix ‘cidal’
means kill. Example: Metronidazole, Cotrimoxazole, Fluoroquinolones, etc.
2.
Bacteriostatic antibiotics: Bacteriostatic antibiotics do not kill bacteria but stop the
growth or replication of bacteria. The suffix ‘static’ means stable. Example: Tertacydines,
Trimethoprim, Macrolides, etc.
On the basis of the effects of antibiotics towards the pathogens, antibiotics are of two types:
1.
Narrow-spectrum antibiotics: Narrow-spectrum antibiotics are active against a selected
group of bacteria. For example, penicillin G is very effective in killing gram-positive
bacteria, but not very effective against gram-negative bacteria. It is used for specific
infection, when the causative organism is known. Narrow-spectrum antibiotic will not
kill the normal microorganisms in the body. Examples are Azithromycin, Clarithromycin,
Clindamycin, Erythromycin, Vancomycin.
Memory Plus
It's good to treat patients with antibiotics that have a narrow spectrum of activity.
The all 'good' bacteria that normally live inside of us will not get killed off along with
the pathogen that caused the infection.
2.
Broad-spectrum antibiotics: Broad-spectrum antibiotics are active against a wider range
of microorganisms, which include both Gram-positive and Gram negative bacteria. They
may be used to treat a variety of infectious diseases. But use of broad spectrum antibiotics
may give rise to drug resistance.
In the case of severe infections, as it takes time to identify the causative bacteria, broad
spectrum antibiotic is used so that there will be no delay in treatment. This occurs, for
example, in meningitis, where the patient can become so ill that he/she could die within
hours if broad-spectrum antibiotics are not given. Examples: Amoxicillin, Levofloxacin,
Streptomycin, Tetracycline, Chloramphenicol.
Advantages and disadvantages of antibiotics
Antibiotics are effective against infections caused by pathogenic microorganisms and many
other diseases. The advantages of antibiotic are as follows:
1.
Some antibiotics have been developed to attack human cells for the treatment of cancer.
2.
They are applied to control bacterial and fungal damage in fruits and grains.
3.
Small amounts of antibiotics are sometimes used to stimulate animal’s growth.
4.
They used as food preservatives in canned or packed foods.
Disadvantages of antibiotics
Overuse of antibiotics is a major concern worldwide. Overuse of antibiotics contributes to the
increase in bacterial infections. The disadvantages of antibiotics are as follows:
1.
Due to overuse of antibiotics, bacteria are becoming resistant to antibacterial medications.
2.
Antibiotics can have side effects, such as diarrhea, vomiting, nausea.
3.
They kill healthy bacteria in the body that can be useful for metabolism.
358
Optional Science - 10
BIOLOGY
4.
Sometimes antibiotics can lead to complications like yeast infections.
5.
Some antibiotics may cause allergy.
Fact with reason
Antibiotics should not be overused, why?
Antibiotics should not be overused or used incorrectly because there is a risk of bacteria
becoming resistant to antibiotics. The antibiotics becomes less effective against such
bacteria and be a problem in curing infections.
Blood Grouping
Although blood is made up of the same basic
components, not all blood is alike. According
to the ABO system of blood grouping, there are
four main types of blood groups- A, B, AB and
O. Our blood group is determined by the genes
we inherit from our parents. A blood group is a
classification of blood based on the presence or
absence of antigens on the surface of red blood
cells (RBCs) and antibodies in blood plasma.
Group A
Group B
,,,,)(j...
.),,,\(/./{";:--
Anti-B
Anli-A
'
B antigen
Group AB
GroupO
Red blood
cell 1ype
Antibodies
in Plasma
Antigens in
Red Blood
Cell
-n--
A antigen
f
),,)(.,i_ _),,,\!/.,
/{";:--
_I!"'\
None
I
Anti-A and Anli-B
,t
A and B
anligens
None
1.
Blood group A has A antigens in the red blood cells with anti- B antibodies in the plasma
2.
Blood group B has B antigens in the red blood cells with anti- A antibodies in the plasma
3.
Blood group O has no antigens in the red blood cells, but has both anti-A and anti- B
antibodies in the plasma
4.
Blood group AB has both A and B antigens in the red blood cells, but no antibodies.
Blood group
O
A
B
AB
Antigens in red blood cell
none
A
B
A and B
Antibodies in plasma
anti-A & anti-B
anti-B
anti-A
None
Fact with reason
Receiving blood from the wrong ABO group can be life threatening, why?
An ABO incompatibility reaction can occur if a person receives the wrong type of blood
during a blood transfusion. For example, if someone with group B blood is given group
A blood, their anti-A antibodies will attack the group A cells. This is why group A blood
must never be given to someone who has group B blood and vice versa. As group O red
blood cells don't have any A or B antigens, it can safely be given to any other group.
The Rh Factor (Rhesus factor)
Red blood cells have another antigen other than antigen A and antigen B. Rh factor is the
protein known as RhD antigen that is present on the surface of RBC. If it is present in our
blood, our blood group is RhD positive. If it's absent, our blood group is RhD negative. This
means there are eight blood groups according to the Rh system:
BIOLOGY
Optional Science - 10
359
ABO blood group system
O
A
B
AB
Rh blood group system
RhD positive
RhD negative
O+
OA+
AB+
BAB+
AB-
Memory Plus
The most well-known and medically important blood types are in the ABO group. They
were discovered in 1900 and 1901 at the University of Vienna by Karl Landsteiner in the
process of trying to learn why blood transfusion sometimes causes death and at other
times saves a patient. In 1930, he belatedly received the Nobel Prize for his discovery of
blood types.
Rh-Factor was first isolated from RBC’s of Rhesus Monkey by Karl Landsteiner and
Wiener in 1940.
Activity
Blood Group Test
Materials Required:
1.
Monoclonal antibodies (Anti-A, B and D)
2. Blood lancet
3.
Alcohol swabs
4. Tooth picks
5.
Sterile cotton balls
6. Clean glass slide
Procedure
1.
Rub the finger tip of a person with the help of the alcohol swab. Alcohol is used as a
disinfectant.
2.
Open the lancet cover, put pressure on the tip of the finger from where blood will be
sampled. Then, prick the finger tip with the opened Lancet.
3.
As blood starts oozing out, make 1 drop fall on three places of the glass slide.
4.
Place a cotton ball at the site where it was pricked. Using the thumb, put pressure on
the area to stop the blood flow.
5.
Take the Anti-A (blue) bottle, place a drop of it on the 1st spot.
6.
Take the Anti-B (yellow) bottle; place a drop on the 2nd spot.
7.
Take the Anti-D (colorless) bottle; place a drop on the 3rd spot.
8.
Take a tooth pick and mix the content in each spot. Use a new tooth pick for each spot.
9.
After mixing, wait for a while to observe agglutination (clumpings).
Observation and Result
If we see clumping in first spot after putting anti-A, then its blood group is A. Similarly,
if we see clumping in blood labeled B after putting anti-B, then its blood group is
B, and if we see clumping in both A and B, then the blood group is AB. Similarly,
agglutination of sample D indicates the Rh+.
360
Optional Science - 10
BIOLOGY
Answer writing skill
1.
What does graft mean?
Graft means the tissue or organ that is transplanted. For example, kidney taken from a
donor person is a graft.
2.
What is isograft?
Isograft is the type of transplantation between the donor and recipient who are
genetically identical, i.e. identical twins. Example: kidney transplantation
3.
Define high blood pressure.
High blood pressure can be defined as blood pressure that is more than 140/ 90mmHg
for a sustained period of time.
4.
Define hyperuricemia.
Hyperuricemia is defined as the condition of high uric acid level in the body. This
condition occurs in the body either when the kidneys excrete too little uric acid or when
the body produces too much uric acid.
5.
The success rate of organ transplantation is very low. Give reasons.
Organ transplantation from a different individual may result in the rejection of the
transplanted organ due to the production of antibodies against the transplanted organ.
This may cause reaction in the blood. Therefore, the success rate of organ transplantation
is very low.
6.
Write the difference between systolic and diastolic pressure.
The difference between systolic and diastolic pressure is as follows:
1.
2.
7.
Systolic pressure
Systolic blood pressure is the pressure 1.
in the arteries as the heart contracts.
It is written usually as the numerator. 2.
Diastolic pressure
Diastolic pressure is the pressure in
the arteries as the heart relaxes.
It is written usually as the
denominator.
Write short notes on the ABO system of blood grouping.
According to the ABO system of blood grouping, there are four main types of blood
groups- A, B, AB and O. A blood group is classified based on the presence and absence
of antibodies and antigens on the surface of the red blood cells (RBCs). The blood of
different persons is determined as A, B, AB and O on the following bases:
i.
Blood group A: If a sample of blood clumps with anti-A serum, then it is Blood Group A.
ii.
Blood group B: If a sample of blood clumps with anti-B serum, then it is Blood Group A.
iii. Blood group O: If a sample of blood does not clump with both anti-A and anti-B
serum, then it is Blood Group O
iv. Blood group AB: If a sample of blood clumps with both anti-A and anti-B serum,
then it is Blood Group AB.
BIOLOGY
Optional Science - 10
0
361
8.
What are the causes of cholesterol?
The causes of cholesterol are as follows:
i.
The primary cause of high cholesterol is genetic.
ii.
Being overweight or obese can also lead to higher blood LDL levels.
iii. Other conditions like diabetes, liver or kidney disease, polycystic ovary syndrome
also raise the level of cholesterol.
iv. Pregnancy and underactive thyroid gland also increase the cholesterol level.
v.
9.
Some drugs like progestin, anabolic steroids and corticosteroids also increase the
LDL cholesterol and decrease HDL cholesterol.
What are the effects of gout?
Gout affects the ankles, heels and toes. The painful gout flare-up is concentrated in the
joints. Patients suffering from gout experience swelling and pain in the ankles, knees,
feet, wrist or elbows. If gout is untreated, it can cause permanent damage to the joints
and kidneys.
10.
Explain in short about the types of antibodies on the basis of the effects of antibiotics
towards the pathogens.
An antibiotic is a chemical substance produced by some microorganisms that have
the capacity to deactivate or kill other microorganisms. On the basis of the effects of
antibiotics towards the pathogens, antibiotics are of two types:
a. Narrow-spectrum antibiotics: Narrow-spectrum antibiotics are antibiotics that
are active against a select group of bacteria. They are used for specific infection
when the causative organism is known. Example: Azithromycin, Clarithromycin,
Clindamycin, Erythromycin, Vancomycin.
b. Broad-spectrum antibiotics: Broad-spectrum antibiotics are antibiotics that are
active against a wider range of microorganisms, which include both gram positive
and gram negative. It may be used to treat a variety of infectious diseases. Example:
Amoxicillin, Levofloxacin, Streptomycin, Tetracycline, Chloramphenicol.
0
362
Optional Science - 10
BIOLOGY
Exercise
Section "A"
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
What is an organ transplantation?
Give the names of the organs that can be transplanted.
Name the organs that are not possible to transplant yet.
What is autograft?
Give one example of each of the followings:
a. autograft
b. isograft
c. allograft
d. xenograft
What is heterograft?
Define blood pressure.
Name the instrument used to measure blood pressure.
What is cholesterol?
What is uric acid?
What is gout?
Define antibiotic.
What is Rh factor?
What do you mean by blood group?
What is artherosclerosis?
Section "B"
1.
2.
3.
4.
5.
6.
7.
8.
9.
Write differences between xenograft and allograft.
What is the difference between isograft and allograft?
Write two differences between systolic blood pressure and diastolic blood pressure.
Write two differences between low density lipoprotein and high density lipoprotein.
What are the types of antibiotics?
Write the difference between bactericidal and bacteriostatic antibiotics.
Differentiate between narrow and broad-spectrum antibiotics.
Write in short about ABO blood group system.
Write a short notes on the Rh blood group system.
BIOLOGY
Optional Science - 10
363
Section "C"
1.
2.
3.
4.
5.
6.
7.
State the advantages of organ transplantation.
What are the disadvantages of organ transplantation?
List the symptoms of high blood pressure.
What is the effect of blood pressure?
What are the symptoms of uric acid?
List the advantages of antibiotics.
What are the disadvantages of antibiotics?
Section "D"
1.
2.
3.
4.
5.
6.
7.
Describe the procedure of organ transplantation.
What are the causes of high blood pressure? Mention some of the control measures of
high blood pressure.
What is cholesterol? What are the types of cholesterol?
What are the effects, causes and control measures of high cholesterol?
What are the causes and control measures of gout?
Describe the procedure of a blood group test in brief.
Explain about the types of antibiotics.
Multiple choice questions
1.
The process of transplanting the organs is called
a) Surgery
b) Keratoplasty
c) Tissue culture
d) Dialysis
2.
The tissue or organ which gets transplanted is called a
a) Graft
b) Sample
c) Keratoplasty
d) Donor
3.
Our normal blood pressure is below
a) 120/ 80
b) 100/ 60
c) 120/ 90
d) 130/ 80
4.
Antibiotics are mostly used to treat
a) Bacteria
b) Fungi
c) Virus
d) Protozoa
5.
If a sample of blood does not clump with both anti-A and anti-B serum, then it is
a) Blood Group A
b) Blood Group B
c) Blood Group AB
d) Blood Group O
6.
Rh factor is present on the surface of
a) RBCs
b) WBCs
c) Blood
d) Plasma
Project Work
Conduct a survey in your neighborhood to compare the blood pressure rate in men and
women. Prepare a report and submit it to your teacher. Ask the blood group of your
friends in class. Prepare a report and submit it to your teacher.
364
Optional Science - 10
BIOLOGY
UNIT
19
THE EARTH
Inge Lehmann (1888–1993) was a Danish seismologist and geophysicist. Based on her
studies on seismology, in 1928 she earned the magister scientiarum degree in geodesy
and accepted a position as state geodesist and head of the department of seismology at the
Geodetical Institute of Denmark. In 1936, she discovered that the earth has a solid inner
core. Lehmann was also the longest-lived woman scientist. She lived to be over 104 years old,
and died in 1993. She received many honours for her outstanding scientific achievements.
She was awarded honourary doctorates from Columbia University in 1964 and from the
University of Copenhagen in 1968, as well as numerous honorific memberships.
Key terms and terminologies of the unit
1.
Minerals: Minerals are naturally occurring non-renewable resources which have
constant chemical composition and stable physical properties.
2. Ores: The combined states of solid minerals from which metal can be extracted are
called ores.
3. Gemstones: A gemstone is a piece of mineral crystal which is used to make jewelry
or other ornaments in its cut and polished form.
4. Natural Gas: Natural gas is a naturally occurring mixture of hydrocarbon gas inside
the earth crust consisting primarily of methane.
5. Fossils: The preserved remains, impression or trace of living organisms which were
buried in the earth's crust million years ago are called fossils.
6. Shaligram: The ammonites found in the Kali Gandaki River of Himalayan region
are called Shaligram in Nepali language.
7. Radioisotope: Radioisotope is a form of an element with an unstable nucleus.
8. Radioactive decay: The process of nuclear disintegration is called radioactive decay.
9. Radiometric dating: The method of finding the age of a material by measuring
radioisotope and its daughter elements is called radiometric dating.
10. Half-life: The time taken to decay half of a sample of radioisotope is called half-life.
Ge o lo gy a nd A st ro n o my
Science - 10
365
Introduction
Earth is a rocky, terrestrial planet. It consists of land, air, water and life. The land contains
active surface with mountains, valleys, canyons, plains, etc. Our home planet is not a perfect
sphere. The north and south poles are slightly flat. The equator is an imaginary circle that
divides earth into two halves. The northern half is called the northern hemisphere and the
southern half is called the southern hemisphere. A major part of the lithosphere lies in the
northern hemisphere while the southern hemisphere is mostly made up of oceans. Nepal is
also in the northern hemisphere of the earth.
Nepal occupies only 0.1 percent of the earth's land surface. It has an area of 147,181 square
kilometers. Nepal is a land-locked mountainous country located at the central part of the
Himalayan belt and bordered to the north by China and to the south, east, and west by India.
About 17 percent of the land is plain and remaining 83% has hills and mountains. Nepal is rich
in different types of natural resources like water, minerals, forest and medical herbs. Various
types of metallic, non-metallic minerals and fossils are found here. In this unit, you will learn
about Nepal's geographic diversity and natural resource, identification of age of the rocks on
the basis of radioactive decay method, etc.
Geologic diversity of Nepal
Nepal is situated in the southern slopes of Himalayas. It has a wide range of geologic diversity
within very short distance. It is like a rectangle in shape with 885 km east-west length and an
average north-south width of 193 km. The landscape of Nepal ranges from 70m in the south
to the highest peak of 8848m in the north from sea level.
Terai Zone
Sub-Himalayan Zone
Lasser-Himalayan Zone
Higher Himalayan Zone
Tibetan Tethys Zone
.. . .....
",
1$ . . . . .
fig: Geological map of Nepal
Geologic structure of Nepal is very complex. The continuous geodynamic process in the
Himalayan region results in many thrusting, faulting, folding and metamorphic events.
Nepal can be divided into five morpho-geotectonic zones from south to north on the basis of
availability of mineral resources. They are: Terai Zone, Sub-Himalayan (Siwalik) Zone, Lesser
Himalayan Zone, Higher Himalayan Zone and Tibetan-Tethys Himalayan zone.
366
Science - 10
Ge o l o gy a nd A s t ro n o my
Terai zone
The southernmost zone is called the Terai. To the north, this zone is separated by an active
thrust system called as the Main Frontal Thrust (MFT) with the Siwalik. The Terai zone is also
called Gangetic Plain. It spreads in 17 percent of the total land area of Nepal.
a.
North to south extension, i.e. width: The width of the Terai zone varies from 10 to 50
km. It extends from the Indian border in the south to the Sub-Himalayan (Siwalik) zone
to the north.
b.
East to west extension, i.e. length: The Terai zone is interrupted by Siwalik for 70 km at
Chitwan and 80 km at the Rapti Valley.
Rocks and Minerals: It has thick alluvial sediments. This zone is rich in boulder, gravel,
silt, and clay. There is high potential for petroleum and natural gas in the Terai zone of our
country.
Sub-Himalayan Zone (Churia/Siwalik foothills)
The Sub-Himalayan zone lies in between the
Terai and Lesser Himalayan zone.
Rocks and Minerals: The Siwalik region is
the potential area for construction materials,
radioactive minerals, petroleum, natural gas
and minor amount of coal. The Siwalik zone
consists of irregularly laminated beds of fine
grained greenish sandstone, and siltstone with
mudstone.
fig: Geographical diversity in Nepal
Lesser Himalayan Zone (The Mahabharata range including mid hills)
The Lesser Himalayan zone lies in between the Sub-Himalayas and Higher Himalayas.
Rocks and Minerals: From east to west, the Lesser Himalayan zone of Nepal varies in rock
type, their age, structures, and igneous rock intrusion. In this zone, high grade metamorphic
rocks are found in the eastern part. This zone is rich in the following minerals:
a.
Metallic minerals mainly iron, copper, lead, zinc, cobalt, nickel, tin, tungsten,
molybdenum, gold, uranium, rare metal, etc.
b.
Industrial minerals like magnesite, phosphorite, limestone, dolomite, talc, clay, kaoline,
graphite, mica, silica sand and quartz.
c.
Gemstones like tourmaline, aquamarine/beryl, garnet, kyanite and quartz crystals.
d.
Fuel minerals like coal, lignite, methane, petroleum, natural gas, hot springs and
radioactive minerals.
Higher Himalayan Zone
The higher himalayan zone is rich in following rocks and minerals.
Rocks and Minerals: It consists of huge pile of strongly metamorphosed rocks. Some of the
areas in the Higher Himalaya are highly promising for precious and semiprecious stones like
ruby, sapphire, and emerald and metallic minerals like lead, zinc, uranium, gold, silver, etc.
Tibetan Tethys Zone
The Tibetan-Tethys zone lies in the northern part of our country. It is rich in following minerals
and rocks.
Ge o lo gy a nd A st ro n o my
Science - 10
0
367
Rocks and Minerals: It is rich in sedimentary rocks, such as shale, limestone, and sandstone.
It also consists of gypsum, brine water (salt) and natural gas. The fossiliferous rocks of this
zone are well-developed in Thak Khola (Mustang), Manang, and Dolpa areas of our country.
This region is 40 km wide.
Status of Mineral Resources in Nepal
Minerals are the non-renewable natural resources. They are formed by various geodynamic
processes. Minerals are naturally occurring non-renewable resources which have constant
chemical composition and stable physical properties.
In Nepal, the Department of Mines and Geology (DMG) and the UN-funded Mineral
Exploration Development Project (MEDP) explored minerals at different part of the country
from 1974 to 1980. Geological investigations and mineral exploration activities carried out
mainly by DMG, UNDP/DMG/MEDP projects, Geological Survey of India (GSI) and a few
private entrepreneurs were able to identify more than 66 minerals in Nepal. Some of the
important minerals are described below.
Metallic mineral
Metallic minerals are those minerals which have a metallic luster and are opaque. Metals are
extracted from their respective ores. Some of the least reactive metals like gold are available
in their native form. Other reactive metals are found in a combined state with other elements
like Oxygen, Sulphur, etc. Thus, the combined states of a metal from which the metal can be
extracted economically are called ores. Some of the important metals in different parts of our
country are given below.
Iron (Fe)
Iron is a widely used metal in the construction works as well as in machinery parts. The main
ores of iron like magnetite, haematite, limonite are reported from more than 85 localities in
Nepal. In Dhaubadi of Nawalparasi, a team of experts had located a huge deposit of iron ore
in 2016 AD. Local people claim that the ore used to be sent up to Palpa district during the rule
of Sen Kings. A governmental team with experts had visited the place and studied the
possibility of extracting iron from the huge deposit.
Other well-known iron ore deposits are Phulchoki
(Lalitpur), Thoshe (Ramechhap), LabdiKhola
(Tanahun), Jirbang (Chitwan), Dhuwakot
(Parbat), Purchaundi/ Lamunigad (Bitadi),
Dahabagar, and Ekghar/ Khanigaon (Bajhang).
These ores are also known from different parts
of Baitadi, Bajhang, Jajarkot, Rolpa, Surkhet,
A team of expert located a
fig: Iron ore
Myagdi, Baglung, Parbat, Chitwan, Ramechhap, fig:
huge deposit of iron in Dhaubadi
of Nawalparasi in 2016 A.D.
Okhaldhunga, Taplejung etc.
Memory Plus
Thoshe iron deposit was mined in small scale during Rana's regime for almost 100 years
till 2006 BS. But it was totally stopped after 2007BS.
368
Science - 10
Ge o l o gy a nd A s t ro n o my
Copper (Cu)
Copper is another important metal which is mainly used in electrical industries to make
copper wires. It is also used to make pots, crafts, alloys, different sculptures, etc. It was mined
traditionally in Nepal long time ago. There is no running copper mine in Nepal at present. The
common copper ores found in Nepal are chalcopyrite, and few malachite, cuprite, chalcocite,
etc. These ores were found in more than 107 localities. The well-known copper ore deposits
are Gyazi (Gorkha), Okharbot (Myagdi), Wapsa (Solukhumbu), Kalitar (Makwanpur), Dhusa
(Dhadhing), Bamangaon (Dadeldhura), Khandeshori/ Marma (Darchula), Kurule (Udayapur),
Bhut Khola (Tanahun), Pandav Khani (Baglung), Baise Khani (Myagdi), Minamkot (Syangja),
Chhirling Khola (Bhojpur), Jantare Khani (Okhaldhunga).
Zinc (Zn) and Lead (Pb)
Zinc is used in galvanizing iron, dry battery, pigments, soldering, dyeing, glue making etc. It
is also used to manufacture various alloys like brass, bronze whereas the lead is used to make
lead sheets, pipes, alloys, pigments, dyeing, insecticide, medicine, etc.
The zinc and lead deposits are reported from more than 54 localities in different parts of
our country. The well-known deposits of zinc and lead ores are found in the Ganesh Himal
area (Rasuwa), Phakuwa (Sankhuwasabha), Labang- Khairang, Baraghare and Damar
(Makwanpur), Pangum (Solukhumbu), Salimar valley (Mugu/ Humla), Phulchoki (Lalitpur),
Sisha Khani and Kandebas (Baglung), Dhuwakot (Parbat), Bhaludanda (Dhadhing, Khola
Khani (Taplejung) etc.
Gold (Au)
Gold is a precious metal with worldwide market. It is widely used in making coins, ornaments,
jewelry, dental appliances, electroplating, metal coating and many other purposes. In Nepal,
alluvial/ placer gold are frequently wined by local dwellers (Botes) from the river gravel/
sediments deposited by the rivers like the Mahakali, Chamliya, Jamari Gad, Seti, Karnali, Bheri,
Rapti, Lungri Khola and Phagum Khola (Rolpa), the Kaligandaki, Myagdi Khola, Modi, Madi,
Marshyangdi, Trishuli, Budhi Gandaki, and Sunkoshi. There is no gold mine yet reported in
Nepal although local people extract small scale of gold from above mentioned rivers.
Silver (Ag)
Silver is mainly used to make ornaments, jewelry, coins, handicrafts, utensils dental fillings,
etc. It is generally associated with zinc-lead ores. In Nepal, small amount of silver is reported in
the zinc-lead ore of Ganesh Himal (Rasuwa), Barghare (Makwanpur) and polymetalsulphide
of Biring Khola (Ilam), Netadarling (Arghakhanchi) and Samarbhamar (Gulmi). Silver ore has
not yet been reported in Nepal; however, it is present in association with zinc-lead ores and
gold.
Nonmetallic Minerals
Nepal is rich in nonmetallic minerals. A numbers of nonmetallic minerals like magnesite,
phosphorite, talc, limestone, dolomite, quartz, mica, clay, silica sand, gemstones, decorative
and dimension stones are known to exist in different parts of Nepal. Some of the explored
nonmetallic minerals are briefly described below:
Ge o lo gy a nd A st ro n o my
Science - 10
369
Limestone
Limestone is the main raw material to manufacture cement. According to a report of the
Department of Mine and Geology (DMG), a number of large to small size limestone deposits
are in Nepal. Preliminary studies indicate that there is a possibility to find more than 2.5
billion tons of cement grade limestone deposits in the Lesser Himalaya zone. Some of the main
cement grade limestone deposits are found in Sinduhuli and Galtar (Udayapur); Bhainse,
Okhare and Nibuwatar (Makwanpur); Jogimara and Beldada (Dhadhing); Chovar,
Bhattedanda (Lalitpur); Balthali and Nandu (Kavre); Kakaru Khola (Sindhuli); Kajeri (Salyan);
Nigale (Dhankuta); Chaukune and Lakharpata (Surkhet); Gandari (Dang); Narapani and
Supa Khola (Arghakhanchi); Diyarigad (Baitadi) and a few other places in Khotang, Syangja,
Palpa, Pyuthan, Sallyan, Rolpa, Rukum, Bajhang, and Darchula districts.
Memory Plus
Limestone is a sedimentary rock composed primarily of calcium carbonate (CaCO3) in
the form of the mineral calcite.
Dolomite
Dolomite occurs as crystals as well as in large sedimentary rock beds. It is used in paints, soap,
detergent and agriculture purpose. In many cases dolomite and limestone occur together.
From geological mapping it is known that there is a probability of occurrence of over 5 billion
tons of dolomite in different localities of Nepal, including Dhankuta, Khotang, Udayapur,
Sindhuli, Dolakha, Kavre, Kathmandu, Makwanpur, Dhadhing, Syangja, Palpa, Baglung,
Gulmi, Arghakhanchi, Dang, Pyuthan, Sallyan, Rolpa, Rukum, Jajarkot, Surkhet, Dailekh,
Jumla, Achham, Doti, Bajhang, Bajura, Baitadi and Darchula districts in the Lesser Himalayan
and in some parts of Higher Himalayan region.
Memory Plus
Dolomite is a type of compact limestone composed of calcium magnesium carbonate
(CaMg(CO3)2).
Phosphorite [Ca₃(PO₄)₂]
Phosphorite is one of the main raw materials to manufacture chemical fertilizers like fused
magnesium phosphate, triple super phosphate etc. Phosphorite is found in Dhik Gad, Junkuna,
Morgaon, Sanagaon and Dhaubisaune areas in Baitadi, Tarugad, Juilgad area as in Bajhang
and further east to Bajura, Sewar Khola (Dang), and Mari Khola (Pyuthan).
Magnesite
Magnesite is a source of magnesium. Magnesite is used to produce synthetic rubber, chemical
fertilizers, etc. It is also used to manufacture high temperature refractory bricks that can be
used for lining in the furnaces, steel industries and crucibles in chemical industries. Preliminary
studies have shown that 180 million tons of magnesite deposit is in Kharidhunga, Dolakha.
It is one of the biggest and best quality magnesite in south Asia. About 20 million tons of
medium to low-grade magnesite deposit is in Kampughat in Udayapur; and a few small size
magnesite occurrences are found in Palpa, Baitadi and Dolakha.
370
Science - 10
Ge o l o gy a nd A s t ro n o my
Memory Plus
~---1
Magnesite is a mineral with the chemical formula MgCO3 (magnesium carbonate).
Talc [H₂Mg₃(SiO₃)₄] or Mg₃Si₄O10(OH)₂
Talcum powder is an important ingredient in many baby powders, foot powders, first aid
powders, and a variety of cosmetics. It is also used in ceramics, paint, paper, roofing materials,
plastics, rubber, insecticides, and as dry fire extinguisher powder. It is found in Lalitpur,
Dolakha, Sindhupalchok, Dhadhing, Chitwan, Tanahun, Kaski, Syangja, Surkhet, Bajhang,
Bajura, Baitadi and Darchula districts.
Red Clay
Red clay is used to manufacture construction materials like bricks, roofing tiles, flooring tiles,
etc. It is also used to make earthen pots and in pigments for painting. Red clay from Panchkhal
(Kavre), Lamosure (Hetaunda), Trijuga/ Beltar (Udayapur), Chidika (Arghakhanchi) and
Guttu (Surkhet) are used in cement factory. Such red clay deposits are also known from
different parts of Nuwakot, Dhadhing, Makwanpur, Nawalparasi, Udayapur, Palpa and
Surkhet districts. Clay from Thimi/ Bhaktpur is used in small-scale pottery industries. A huge
amount of silty clay deposit in different parts of the Kathmandu Valley and other parts of our
country is used to manufacture bricks. In villages, it is also used in house wall painting.
liiii~ - - ~---1
1~~ - - Memory Plus
Red clay is a highly weathered clay deposit mineral which contains mostly hydrated
silicates of aluminum and iron oxides.
Ceramic clay or Kaolin
Clay is a natural material that is obtained from the ground but ceramics are various materials,
including clay, which hardens when heated. Kaolin is mainly used in ceramics. It is also used
in medicine, paper, cosmetics, etc. Irregularly distributed kaolin are known from Daman
(Makwanpur), Panchmane (Kathmandu), Dalchhap and few other places.
Memory Plus
Ceramic clay or Kaolin is a type of soft white clay. The primary constituent in kaolin is a
hydrated aluminium silicate.
F-~~ ====================I
Know the Reason
Kaolin is also called China clay, why?
Kaolin is named after the Kao-ling mountain in China where it was first mined, for many
years before it was discovered in Europe in 1745. It is a source of white chinaware. So
Kaolin is also called China clay.
Ge o lo gy a nd A st ro n o my
Science - 10
371
Graphite
Graphite is mainly used in lead pencils, crucibles, paints, lubricants etc. It is one of the
significant minerals in metamorphic terrain in Lesser Himalayan region. It is reported from
different localities like Ilam, Dhankuta, Sankhusabha, Nuwakot, Sindhupalchok and
Dadeldhura.
Memory Plus
Graphite is a naturally occurring form of crystalline carbon. It is a native element mineral
found in metamorphic and igneous rocks.
Brine/Salt
Brine is a high-concentration solution of salt in water. It may refer to salt solutions ranging
from about 3.5% up to about 26% which is in a typical saturated solution. In Nepal, brine
water is available in the Narsing Khola (Mustang), Chhiding Khola and Chharkabhot (Dolpa).
It is tapped and dried for common salt production. Brine water of these areas contains 1.5 to
3% NaCl. So far mineable deposit of brine is not found in our country.
Gemstones
A gemstone is a piece of mineral crystal which is used
to make jewelry or other ornaments in its cut and
polished forms. Gemstones consist of hard crystalline
substances with unique chemical and physical
properties. Gemstones are popularly mentioned in
the myths and legends of human cultures throughout
history. They are believed to have special powers.
Traditionally, gemstones are considered as precious
and semiprecious.
Precious Gemstones
diamod
garnet
amethyst
sapphire
ruby
emerald
peridot aquamarine
topaz
opal
citrine
fig: gemstones
zircon
Diamond, Ruby, Sapphire and Emerald are considered precious gemstones.
Rubies and Sapphire
Ruby and Sapphire are the two precious gemstones found in Nepal. They are gems of the
mineral which has chemical composition of aluminium oxide (Al2O3).
Generally small crystals of light red to red ruby and light to dark blue coloured sapphire are
known from Chumar, Ruyil, Shelghar, Pola, Shongla (Dhadhing) and Lari/ Ganesh Himal
area (Rasuwa). They are found in highly folded metamorphic rocks.
Semiprecious Gemstones
All gemstones other than precious gemstones are considered as semiprecious gemstones.
Semiprecious gemstones found in Nepal include tourmaline, aquamarine/ beryl, garnet,
kyanite, amethyst, citrine, smoky quartz (quartz crystals).
Tourmaline
Tourmaline is the earth's most colourful mineral and gem material. It is available in pink,
bright green, light orange sometimes with repeated colour banding, olive green with amber
coloured core. It is found in the Langtang Valley (Rasuwa), Naje (Manang), Daha (Jajarkot),
etc. Tourmaline crystals are cut and polished for gem.
372
Science - 10
Ge o l o gy a nd A s t ro n o my
Beryl/ Aquamarine
The Beryl gems are named by their colour as emerald (green), aquamarine (greenish blue to
blue), etc. Aquamarine of Taplejung (Ikabu, Lodantar) area is highly expensive. Phakuwa
(Sankhuwasabha), Lekhpatan and Tikachaur in Jajarkot; Jagat, Panchmane, Kagtigaon in
Kathmandu, Baguwa, Tarkeghyang, Nibuwagaon in Sindhupalchok are the other known
localities for Beryl.
Garnets
Garnets are a group of silicate minerals with combinations of metals within it. Red is the most
common colour, although it exists in different colours, including green, purple, black and blue.
Garnetsare found in metamorphic rocks in higher Himalayan region. Deep red or purplish red
coloured almandine, hessonite and pyrope garnet are found mainly in Sankhuwasabha and
Taplejung districts.
Kyanite
Kyanite is a mineral found mainly in metamorphic rocks. In Nepal, Kyanites are reported from
different localities like Dolakha, Sankhuwasabha, Taplejung, Rasuwa, Dhadhing, Jajarkot and
Achham districts. Some small-scale kyanite mines are in operation in Daha and Suneri in
Jajarkot and Barah of Aachham districts. Kyanite crystals are cut for gems.
Dimension Stones/Decorative Stones
Dimension stone is a collective name used for various natural stones which are trimmed to
specific size or shape for structural or decorative purposes in construction or monumental
applications. For example, granite, marble, quartzite, slate, etc.
Marble
Marble is a metamorphic rock. It is used for bathroom floors, wall covering and many other
decorative purposes in the residential and commercial buildings. In Nepal, about 1.63 billion
tons of pink, gray, and white coloured marble deposit is in Godawari (Lalitpur). It is also
found in Anekot (Kavre); Chhatre Deurali (Dhadhing); Bhainse and Sukaura (Makwanpur).
Granites
Granite is an igneous rock. Polished granite is used in flooring tiles, stair trades, kitchen
countertops and many other decorative features. Rough cut granite is used in buildings,
bridges, paving monuments, etc. In Nepal, granite is known from different localities like
Makwanpur (Palung and Ipa), Sindhuli, and Udaypur in the Lesser Himalayan region.
Quartzite
Quartzite is a metamorphic rock formed from quartz rich sandstone. It is a hard rock and
resistant to weathering. It occurs naturally in various forms, colours, designs and textures.
So it can be used for decorating outdoor and walls of the house. It is abundantly known from
many districts like Taplejung, Ilam, Dhankuta, Ramechhap, Sindhupalchok, Makwanpur,
Dhadhing, Tanahun, Kaski, Syangja, Parbat, Baglung, Achham, Doti, Bajhang, Bajura,
Dadeldhura, Baitadi and Darchula.
Slate
Slate is a fine-grained, homogeneous metamorphic rock derived from shale type
sedimentary rock. It is particularly used as roofing material. Slate tiles are used for
flooring, in stairs and walkways. It is also used for blackboards and writing slates.
Ge o lo gy a nd A st ro n o my
Science - 10
373
It is extensively mined from many districts like Dhankuta, Sindhupalchok, Ramechhap,
Nuwakot, Sindhupalchok, Dhadhing, Tanahun, Baglung, Syangja, Palpa, Parbat, Jajarkot,
Achham, Doti, Dadeldhura, Baitadi, Bajhang and Bajura.
Fuel Minerals
The minerals that can be used as fuel are called fuel minerals. For example, coal, petroleum
and natural gas. They are stripped from the earth. The lesser Himalayan region in Nepal
consists of coal, lignite, methane gas, petroleum, and natural gas.
Fossils found in Nepal
Volcanic activity and earthquakes on the earth alter the landscape in a dramatic way. Living
organisms get trapped inside the earth crust during changes on the earth's surface. A fossil
is a evidence of a once-living organism. The preserved remains, impression or trace of living
organisms which were buried in the earth's crust million years ago are called fossils. Fossils
can be the preserved entire body of the organism or just part of the body like bones, shells,
feathers, leaves etc. in sedimentary rocks. The fossil findings of plants and animals from Nepal
are supporting evidences in context of the geologic history of the Himalayas.
Cephalopod Fossils/ Ammonites (Shaligram)
A cephalopod is any member of the
molluscan class like squid, octopus,
etc. The extinct cephalopod molluscs
with a flat-coiled spiral shell are called
ammonoids.
Ammonites
are
the
fig: Shaligram
ammonoid fossils. The term ammonite is
derived from a term ammonis cornua which means the horn of Ammon; an Egyptian god who
wore curled horns on his head. They are among the most abundant fossils found in different
ports of the earth.
In Nepal, ammonites are found in the Himalayan region, Mustang. The ammonites found
in the Kali Gandaki River of Himalayan region are called Shaligram in Nepali language.
Shaligrams are black fossils. According to geologists, saligrams are 140 to 165 million years
old and found in two colors, black and white It is worshiped as a symbol of God Vishnu in
the homes of Vaisnava sect of the Hindus. The spiral shells in ammonites are the fossils of
ammonids. According to geologists, Shaligrams are 140 MY-165 MY old.
Memory Plus
Shaligram in the river look like black balls. Due to its specific colour the river was named
Kali Gandaki.
Brachiopod and Gastropod Fossils
The Siwalik zone is also rich in fossils. Fossils of plants, pisces, reptiles and mammals have
been reported from the Siwalik zone. The mudstone beds of the upper Siwalik contain many
invertebrate fossils, including the fossils of Brachiopods and Gastropods. Brachiopods are the
marine animals that have hard valves on the upper and lower surfaces. These animals evolved
at least 550 MY ago. The gastropods are commonly known as snails and slugs.
374
Science - 10
Ge o l o gy a nd A s t ro n o my
Some Fossils in Collection at the Natural History Museum (NHM)
The Natural History Museum (NHM) in Kathmandu was established in 1975. Since then it
has provided with more than 50,000 specimens of Nepal's modern and prehistoric plants and
animals. Some 964 fossils from the territory of Nepal are preserved in it. On December 31,
2013, the Department of Postal Services of Nepal issued a set of four stamps showing fossils of
extinct animals which are in the collection of the Natural History Museum (NHM). They are
briefly described below:
a.
Giraffa punjabiensis
It is an extinct giraffe. The genus Giraffa evolved almost 25 million
years ago. The extinct Giraffa punjabiensis inhabited in large parts of
Eurasia, including the ancient land of Nepal. The molar teeth of this
extinct Giraffe are in collection of the NHM. The teeth were found on
the banks of Surai Khola.
b.
Archidiskidon planifrons
It is an extinct elephant. Many fossilized body parts of the elephant,
Archidiskidon, were recorded from different parts of Nepal. There is
a fossilized skull of the Archidiskodon at the NHM. This species of
elephant roamed the Siwalik Hills of Nepal around 3 million years
ago. It was found on the banks of Rato Khola.
c.
Ramapithecus sivalensis
It is an extinct humanoid. The fossil remains of this animal is
estimated to be 12.5 million to 8.5 million years old. The molar teeth
of the ancient hominoid Ramapithecus which is in the collection of the
NHM is estimated to be 9.0 – 9.5 MY old. It was discovered in Tinau
Khola on way to Tansen from Butwal. Ramapithecus was understood
to have direct ancestral roots to modern humans.
d.
Hexaprotodon sivalensis
It is an extinct Hippopotamus. The fossil remains of this animal is
estimated to be 5.35-0.11 MY old. Fossils of this species have been
found in Indonesia, India, Sri Lanka and Nepal. In Nepal the fossils
of Hexaprotodon sivalensis were discovered at Gidniya Village and Rato
Khola. The skull and lower jaw of this extinct hippopotamus are also
in the collection of the NHM.
Estimation of Age of Rocks
Age of the rocks can be determined with the help of different methods. Relative dating and
absolute dating are the two effective methods to estimate the age of rocks.
Relative dating method
Relative dating is the science of determining the relative age of rocks comparing with another,
without determining their absolute age. In this method the fossils and layers of rocks are
placed in an order from older to younger. It can only establish whether one rock is older or
younger than another.
Ge o lo gy a nd A st ro n o my
Science - 10
0
375
Absolute or numeric dating method
Absolute dating is the process of determining specific age of rocks independently without
comparing with others. Absolute dates for rocks are obtained with radiometric dating.
Radiometric Dating or Radioactive Dating
Radioisotope is a form of an element with an unstable nucleus. For example, uranium-238
(U238), carbon-14 (C14), etc. Atoms of a radioisotope become atoms of other elements as their
nucleus disintegrates. It is called radioactive decay. Thus, the process of nuclear disintegration
is called radioactive decay. For example, radioisotope of uranium-238 (U238) decays into
thorium-234 (Th234). The predictable products of radioactive decay are called daughter
elements. In the radioactive dating, the age of rocks is determined from the decay of their
radioactive elements. The method of finding age of a material by measuring its content of
radioisotope and daughter elements is called radiometric dating. It is also called radioactive
dating. In this method, a radioactive isotope with known half-life is considered in counting to
establish the absolute age of the fossil or rock.
Half-life
The time taken to decay half of a sample of radioisotope is called half-life. For example, the
half-life to decay U238 to Pb206 is 4.5 billion years.
Radiometric Dating Techniques
The most well-known way to determine the age of rocks and fossils is through the use of
radiometric dating. In most cases, the radiometric dating techniques use the rate of change of
elements into isotopes. Sometimes, the fossils themselves are not dated. Instead of fossils, the
rocks around the fossils are dated to estimate the age of the fossils. Some of the commonly
used techniques are: Radiocarbon dating (use carbon-14 isotope), Uranium-lead dating (use
lead-206 and lead 207 isotopes), Uranium-thorium dating, Potassium-argon dating, Argonargon dating, etc.
The time in year which shows how long ago a rock was formed is called absolute age of a rock.
In radiometric dating, half-life of a radioisotope is applicable to find absolute age of a rock.
Parents and daughters for uranium and carbon isotopes and the corresponding half-life are
given in the table below.
Unstable Radioisotope
(Parent)
Uranium-238
Uranium-235
Carbon-14
More stable breakdown product
(Daughter)
Lead-206
Lead-207
Nitrogen-14
Half-life (in years)
4.47 billion
700 million
5730±40
Radio-Carbon Dating
Isotopes are the different atoms of an element with different number of neutrons in their
nucleus. The three isotopes of carbon are ₆C12 (nucleus containing 6 protons and 6 neutrons),
₆C13 (nucleus containing 6 protons and 7 neutrons), and ₆C14 (nucleus containing 6 protons
and 8 neutrons). Among these ₆C12 and ₆C13 are stable in nature. Such carbon atoms occupy
almost 99.99% of total carbon existence in nature. The isotope ₆C14 is highly radioactive. So the
carbon dating method uses ₆C14 isotopes which continuously undergo decaying into stable
₇N14 atoms by releasing β-particles with the half-life of 5730±40 years. Thus, the use of ₆C14
isotope to determine the age of organic materials which contain abundant carbon is known as
radio-carbon dating.
0
376
Science - 10
Ge o l o gy a nd A s t ro n o my
Natural production of ₆C14 in the atmosphere
₆C14 is continually being formed in the
atmosphere by the effect of cosmic ray
neutrons on nitrogen 14 atoms. The neutron
from cosmic rays knocks a proton from
nitrogen-14 atoms and forms C-14 atom.
₇N14 + ₀n¹
₆C14 + 1p1
The highest rate of ₆C
9 km to 15 km.
14
cosm1c,adlat1on
I
I
e nau11on
14
N-
-
•"er
o proton
I
0
co, ---+
atmospheric. gasses
'
fig: ₆C¹⁴ in living beings
production takes place in upper region of troposphere at altitudes of
₆C14 in living beings
₆C14 is chemically identical to the other two isotopes of carbon. It quickly combines with the
oxygen in the atmosphere to form CO₂. Photosynthesis incorporates ₆C14 into plants and then
enters into the body of animals that eat the plants. ₆C14 gets dissolved in water and enters
in the oceans, lakes and rivers. From there it assimilates into aquatic organisms. Organisms
exchange carbondioxide with atmosphere throughout their life by respiration and excretion.
Decay of ₆C14
When a plant or animal dies it no longer
12.5%
100%
50%
25%
exchanges CO₂ with the atmosphere. It stops
the entrance of ₆C14 into the body of organisms.
This starts the radioactive decay. ₆C14 atom
decays by emitting an electron. This process Age 0
Age 5730 yr Age 11,460 yr Age 17,190 yr
converts a neutron to a proton and ₆C14
fig: Estimation of age on the basis of half-life
converts back to its original ₇N14 form.
By knowing how much carbon 14 is left in a sample, the age of the
75
Carbon•14
organism when it died can be known. ₆C14 atoms decay at the rate of 50% 100~
E 50
every 5,730 years. So after 11,460 years 25% will be left, after 17,190 years .. 25
12.5% will be left, and so on. The graph alongside shows the relation
0
n,(:) ~(:)
~ ,"''$. ,I\" ~re, ~'bro years
between the percentage carbon-14 atoms left in the sample and the
corresponding age.
f
~
,.,(:)
'!a(:)
~(:)
Memory Plus
The duration of half-life of ₆C14 is only 5730±40 years. So radiocarbon dating method is
appropriate to find the age of the rock or any carbon containing sample which is not older
than 62,000 years only.
Uranium-Lead Dating
Uranium-Lead dating method uses 92U238 as a parent element whose daughter product is
Pb206 with half-life of 4.47 billion years. It also uses 92U235 as a parent element whose daughter
82
product is 82Pb276 with half-life of 710 million years. The number of parent element decreases
with time. On the other hand the product atoms keep increasing. Uranium decays into lead at
a predictable rate. By finding the ratio of parent and daughter products, the time of the origin
of the rock can be determined.
Ge o lo gy a nd A st ro n o my
Science - 10
0
377
Estimation of age of the mineral Zircon
Zircon consists primarily of zircon silicate. Some molecules in a zircon crystal have uranium
atoms instead of zirconium atoms. If a zircon crystal consists lead in it then the lead is
radiogenic which is formed by the radioactive decay of uranium. Uranium decays into lead at
a predictable rate. Thus, the number of uranium atoms from zircon crystal decreases with time
when they change into lead. During this decay, lead atoms accumulate in the crystal. Finally,
the ratio of uranium atoms to lead atom in a zircon crystal is used to calculate how long ago
the crystal formed. The ratio of uranium atom to lead atoms in a zircon crystal gives its age.
Mathematically,
100% of parent isotopes = newly formed rock (0Year)
50 % of parent isotopes = one half-life = 4.5 billion years
25 % of parent isotopes = two half-life = 2×4.5 billion years
Memory Plus
Uranium-Lead dating is one of the oldest method in the history of radioactive dating of
rocks and minerals that were formed about 1 million years to over 4.5 billion years ago.
The oldest known terrestrial rock, a tiny zircon crystal from Australia, is 4.404 billion
years old.
Uranium-lead radioactive dating can also be used on baddeleyite, monazite minerals.
Uranium-thorium dating method
Uranium-thorium dating is also called thorium-230 dating. In this method, an isotope
of uranium (92U234) is decayed into thorium (90Th230) with half-life of about 80,000 years. In
between uranium and thorium, uranium is water soluble whereas thorium is not. Due to this
hydrophilic and hydrophobic natures of uranium and thorium isotopes respectively, they are
used selectively into the ocean floor sediments. The age of the rocks is calculated by finding
their ratios (uranium-234/thorium-230).
378
Science - 10
Ge o l o gy a nd A s t ro n o my
Answer writing skill
1.
Write the name of the five major tectonic zones in Nepal.
The five major tectonic zones in Nepal are: Terai (Gangetic plain), Sub-Himalayan Zone
(Siwalik), Lesser Himalayan Zone, Higher Himalayan Zone, and Tibetan-Tethys Zone.
2.
Name two precious gemstones found in Nepal.
Ruby and Sapphire are the two precious gemstones found in Nepal.
3.
Name the fossils collected at the Natural History Museum (NHM) Nepal.
The fossils collected at the Natural History Museum (NHM) Nepal are Giraffa
punjabiensis, Archidiskidon planifrons, Ramapithecus sivalensis and Hexaprotodon
sivalensis
4.
'Nepal is rich in natural resources but their exploration and exploitation is challenging.'
Justify this statement in two points.
a.
Nepal has a rough irregular surface with difficult mountain terrain.
b.
There is a lack of skilled manpower, infrastructure and financial support.
So exploration and exploitation of mineral resources are still challenging in Nepal.
5.
6.
Write uses of marble, granite and slate.
a.
Uses of Marble: It is used for bathroom floors, wall covering and many other
decorative purposes in the residential and commercial buildings.
b.
Uses of Granite: Polished granite is used in flooring tiles, stair trades, kitchen
countertops and many other decorative features.
c.
Uses of Slate: It is particularly used as roofing material. Slate tiles are used for
flooring, stairs, walkways, etc. It is also used for blackboards and writing slates.
Which types of mineral resources are found in different geological regions of Nepal,
explain.
Nepal is rich in mineral resources. Gravel, sand, ground water, petroleum and natural gas
are found in the southernmost Terai plain. The Sub-Himalaya region has construction
materials, radioactive minerals, petroleum, natural gas and minor amount of petrified
coal. Likewise, metallic minerals mainly iron, copper, lead, zinc, etc., industrial minerals
like magnesite, phosphorite, limestone, dolomite, talc, kaoline, graphite, etc., gemstones
and fuel minerals like coal, methane gas, petroleum and natural gas are found in the
Lesser Himalaya zone. Some of the areas in Higher Himalaya are highly promising for
precious and semiprecious stones like ruby, sapphire and emerald, and metallic minerals
like lead, zinc, uranium, gold silver etc. Tibetan Tethys zone possesses limestone,
gypsum, brine, radioactive minerals and natural gas.
Ge o lo gy a nd A st ro n o my
Science - 10
0
379
Exercise
1
Step
A.
Define
1.
4.
B.
Mineral
Radioisotopes
Very Short Answer Questions
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
What are the five geographic divisions of Nepal from north to south?
Name any four metallic minerals found in Nepal.
Write the name of any two dimension stones found in Nepal.
Name two gem stones found in different localities of Nepal.
What are fossils?
Name any two fossils of extinct animals found in Nepal.
What are Shaligrams?
Write two methods to determine age of rocks.
What is carbon dating?
Write any three radiometric methods to determine age of rocks.
Step
A.
1.
2.
3.
4.
5.
2. Ore
3. Gemstones
5. Half-life
2
Short Answer Questions
Mention any two special features of following zones of Nepal.
a. Terai
b. Sub Himalayan Zone
c. Lesser Himalayan Zone
d. Higher Himalayan Zone
e. Tethys Himalayan Zone
Write two localities each of the following metallic minerals found in Nepal
a. Iron (Fe) b. Copper (Cu)
c. Gold (Au)
d. Silver (Ag)
Write two localities each of the following non-metallic minerals found in Nepal
a. Limestone
b. Dolomite
c. Phosphorite
d. Magnesite
e. Talc
f. Red Clay
g. Ceramic clay or Kaolin
h. Graphite
Write about followings:
a. Cephalopod Fossils in Nepal
b. Brachiopod and Gastropod Fossils in Nepal
Write in short about any two extinct animals whose fossils are in the Natural History Museum
(NHM).
380
Science - 10
Ge o l o gy a nd A s t ro n o my
6.
How is the status of fuel minerals in Nepal?
B.
Differentiate Between
1.
2.
Radiocarbon dating and Uranium-lead dating
Relative dating method and absolute dating method
C.
Give Reason
1.
2.
Kaolin is also called China clay
Radiocarbon dating method is appropriate to find the age of the rock which is not older than
62,000 years only.
Step
1.
2.
3.
Write applications of decorative stones found in Nepal.
Exploration and exploitation of gemstones found in Nepal can be a source of national
economy. Illustrate this with example.
Nepal has a huge potential of natural resources. Illustrate it with three supporting points.
Step
1.
2.
3.
4.
5.
6.
3
4
Explain about the geologic diversity of Nepal.
How is the status of following minerals in Nepal, explain in brief.
a. Metallic minerals
b. Non-metallic minerals
c. Decorative stones
d. Gemstones
Explain in short about the uranium-thorium dating to find the age of rocks.
Compare radiocarbon dating with Uranium-lead dating and Uranium-thorium dating
individually.
Explain in short about the carbon dating to find the age of fossils.
Mention the role of Natural History Museum (NHM) in preserving the different fossils found
in Nepal.
Multiple Choice Question (MCQs)
1.
2.
3.
4.
5.
The non-metallic mineral composed of calcium magnesium carbonate is
a. Limestone
b. Dolomite
c. Phosphorite
d. Magnesite
In Nepal, ammonites are abundantly found in
a. Mustang
b. Manang
c. Dolpa
d. Ilam
The Natural History Museum (NHM) in Kathmandu was established in
a. 1965
b. 1975
c. 1985
d. 1995
The half-life of the decay U238 to Pb206 is
a. 4.47 billion years
b. 2.5 billion years
c. 5.5 billion years
d. 3.5 billion years
In Uranium-Lead Dating, the parent element used is
a. U235
b. Pb206
c. Pb238
d. U238
Ge o lo gy a nd A st ro n o my
Science - 10
0
381
UNIT
20
THE
UNIVERSE
Edwin Powell Hubble (1889–1953) was an American astronomer. He studied law in
Bachelors and got Bachelor of Science degree in 1910. He earned his Master's degree from
The Queen's College, Oxford. Hubble played a crucial role in establishing the fields of
extragalactic astronomy and observational cosmology. He is regarded as one of the most
important astronomers of all time. Hubble's Law implies that the universe is expanding.
Hubble's name is most widely recognized for the Hubble Space Telescope which was
named in his honor.
Key terms and terminologies of the unit
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
382
Universe: The vast space consisting of everything like stars, planets, minor
planets, moons, galaxies, energy, time, etc. is called the universe.
Constellation: The small group of stars seen in the sky especially at night with
fixed shape is called constellation.
Space Exploration: Space exploration is the ongoing discovery and exploration
of the celestial structures in outer space by means of continuously evolving and
growing space technology.
Artificial Satellite: An artificial satellite is an object that people have made and
launched into orbit using rockets.
Spacecraft: A spacecraft is a vehicle, or machine designed to fly in outer space.
Robotic spacecraft: A robotic spacecraft is an unmanned vehicle or machine
designed to fly in outer space.
Space probe: An unpiloted, unmanned device sent to explore space and gather
scientific information is called a space probe.
International Space Station (ISS): The International Space Station is a spacecraft
capable of supporting crewmembers while orbiting around the earth as like a
satellite in the low earth orbit.
Space shuttle: Space shuttle is a rocket-launched reusable spacecraft designed to
transport people and cargo between the earth and space.
Planetarium: A planetarium is a theatre built primarily for presenting educational
and entertaining shows about astronomy and the night sky, or for training in
celestial navigation.
Science - 10
Ge o l o gy a nd A s t ro n o my
Introduction
On a clear, dark night, our eyes can see so many stars in the sky. They all are in a negligibly
small dimension of the universe. The vast space consists of everything like planets, moons,
minor planets, stars,galaxies, intergalactic space, energy and time is called the universe.
Mysteries of the universe kept some people busy in thinking about revealing the facts behind
it. One of the common idea of all time was a close obervation of the celestial masses and the
phenomena by going far away from the earth's surface.
The concept of propelling light man-made stuffs in air begin with ancient civilization. Later on
the advancement in technology made it possible to propel heavy stuffs like messile, rockets,
satellites, etc. in the sky. Here in this unit you will go through a brief historical background of
the space exploration. You will also learn about the telescope used to observe the outer space
and planeterium.
Space Exploration
Space exploration is the ongoing discovery and exploration of celestial structures in outer
space by means of continuously evolving and growing space technology. The study of space
is carried out mainly by astronomers with telescopes. But the physical exploration of space is
conducted both by unmanned robotic spacecraft and human spaceflight.
History of Space Exploration
We look up at the sky and wonder about the sun, moon, stars, and celestial events. Since ancient
times, people around the world have tried to unfold the mystery of outer space. But their
work was just in prediction and the earth-based observations without using advanced space
technology. The space exploration became more scientific with the technological advancement
in the 20th century. It began in the late 1950s with the development of powerful rockets. After
that, hundreds of satellites, investigations and space shuttles have been launched. They have
explored near-earth space. A permanent space station is in the orbit around the earth. Now
astronomers have collected a lot of information about the outer space. They are still working
continuously in their missions of the space exploration. The future exploration includes
building a colony on Mars, searching for life in other galaxies and other exciting programmes.
Space Exploration Idea from the Military Use of Rockets
The Chinese used rockets for ceremonial and
military purposes centuries ago. In the history
of true use of rockets, Chinese used gun powder
fire-arrows as a simple form of a solid-propellant
fig: chines fire-arrows
rocket in 1232 in war with Mongols.
With the fall of Germany in World War -II (1939-1945), many German rocket scientists reached
the United States (US). Others went to the Soviet Union (USSR). Both the United States and
the Soviet Union realized the potential of rocket as a military weapon. They began a variety
of experimental programmes. They engaged in a long competition to develop rockets for both
warfare and the exploration of space.
~ II I! .
Ge o lo gy a nd A st ro n o my
Science - 10
383
Father of Modern Astronautics
The science and technology of space travel and exploration is called astronautics. In 1898,
Konstantin Tsiolkovsky (1857-1935) proposed the idea of space exploration by rocket. He was
a Soviet rocket scientist and pioneer of the astronautic theory. In a report published in 1903,
he suggested use of liquid propellants for rockets in order to achieve greater range. For his
ideas, careful research and great vision, Tsiolkovsky has been called the father of modern
astronautics. During the same period designing rocket engines for spaceflight occurred
simultaneously in the other two countries too. In United States, by Robert Goddard; and in
Germany, by Hermann Oberth.
The V-2 rocket
In the 1930s and1940s Nazi Germany saw the possibilities of using long-distance rockets as
weapons. The first rocket which could fly high enough to get into space was the V-2 missile
which was first launched by Germany in 1942. In World War II, London was attacked by
200-milerange V-2 missiles, which arched 60 miles high over the English Channel at a speed
more than 3,500 miles per hour.
Two- Stage rocket: The Bumper 8
A new chapter in space flight began in July 1950 with the launching of the Bumper 8. It was
built by the United States.
The Start of Space Race
The Space Race refers to the 20th century Cold War between the United States and the Soviet
Union to develop aerospace capabilities, including artificial satellites, unmanned space
investigations and human spaceflight. It begun in 1955 when both the countries announced
that they would soon be launching satellites into the orbit around the earth.
The world's first satellite; 'Sputnik 1' was launched on October 4, 1957 by the Soviet Union
(USSR). Sputnik 2 was launched on November 3, 1957. It carried a dog named Laika, which
became the first animal to reach space. The experiment aimed to prove that a living passenger
could survive being launched into orbit. But the dog was said to have died within hours due
to overheating.
The first U.S. satellite, 'Explorer 1', went into orbit on in January 31, 1958. Alan Bartlett Shepard
became the first American astronaut into space on May 5, 1961. His sub-orbital flight was of
15-minutes.On February 20, 1962, John Glenn’s historic flight made him the first American to
orbit Earth.
Memory Plus
Following the Sputnik 1, Explorer 1 was the first satellite launched by the United States
on January 31, 1958. But it entered the earth's atmosphere and burnt on March 31, 1970.
The Soviet Space Programme achieved many successes including the first living being in
orbit in 1957, the first human spaceflight in 1961. Soviet cosmonaut Yuri Gagarin was the
first human being to travel into space. On April 12, 1961, he was launched into orbit on the
spacecraft Vostok 1. The flight was of 1 hour 48 minutes to orbit the planet. Gagarin reached
an altitude of 327 kilometers (about 202 miles). After this achievement a "space race" quickly
developed between the United States and the Soviet Union.
384
Science - 10
Ge o l o gy a nd A s t ro n o my
The United States was upset that the Soviets always seemed to be the first in everything in
the space programme. Therefore, the U.S. made the goal to land on the moon first. “Landing
a man on the moon and returning him safely back to Earth within a decade” was a national
goal set by President John F. Kennedy in 1961. The United States finally succeeded in landing
the first humans on the moon on July 20, 1969 with Apollo 11. Neil Armstrong became the
first men on the moon and then Buzz Aldrin. These efforts are often taken as landmarks for
space exploration. Six Apollo missions were carried out to explore the moon between 1969 and
1972. While the United States focused on the manned Apollo programme, the Soviet Union
conducted unmanned missions that deployed rovers and returned samples to the earth. While
the United States focused on the manned Apollo programme, the Soviet Union conducted
unmanned missions that deployed rovers and returned samples to the earth.
Fact with reason
Many space missions are more suited to robotic spacecraft than the crewed operation, why?
In comparison with the crewed spacecraft, robotic spacecraft have lower cost and lower
risk factors. In case of some planetary destinations such as Venus, the vicinity of Jupiter,
etc. are too hostile for human survival. Outer planets such as Saturn, Uranus, and
Neptune are too distant to reach with current crewed spaceflight technology. So robotic
spacecraft are the only way to explore them.
A Priority Shift from one-off Flights to the Renewable Hardware
After the first 20 years of exploration, focus shifted from one-off flights to renewable
hardware, such as the Space Shuttle programme and Space Station. Skylab. Skylab was the
first United States space station launched and operated by NASA, and occupied for about 24
weeks between May 1973 and February 1974 – the only space station the U.S. has operated
exclusively. In 1979 it fell back to Earth. The Soviet programme continued to break ground in
science with the Mir space station. Mir was the first modular space station and was assembled
in orbit from 1986 to 1996. It was the largest artificial satellite in the orbit, succeeded by the
International Space Station after Mir's orbit decayed.
International Space Station (ISS)
The International Space Station (ISS) is
a spacecraft capable of supporting crew
members while orbiting around the
earth as like a satellite in the low earth
orbit. It is a large space station that
orbits 354 kilometers above the earth.
There are astronauts and cosmonauts
living on board of the ISS right now.
Other spacecraft like 'space shuttle's
orbiter' can be docked on space station
to carry astronauts to and from the
International Space Station.
fig: International Space Station (ISS)
Ge o lo gy a nd A st ro n o my
Science - 10
385
The first piece of the ISS was launched in November 1998. But in November of 2000, the
International Space Station opened its doors to the first visitors, astronauts and cosmonauts.
Several more pieces have been added since then. The expansion of ISS has not completely
finished yet. New sections will be added to the ISS in the next few years. Russia, the United
States, and 14 other countries are now working together on the International Space Station
project.
Memory Plus
First Crew to the International Space Station were launched on October 31, 2003.
Space Shuttle
Space shuttle is a rocket-launched reusable spacecraft
designed to transport people and cargo between the earth
and space. It is used to make repeated journeys between
the earth and space to carry up astronauts, sometimes a
satellite or other equipment into orbit. The first launch of
the Space Shuttle Columbia occurred on 12 April 1981,
exactly 20 years after the first manned space flight. It was
the orbiter Columbia, with two crew members lifted off
from the Kennedy Space Center.
The Space Shuttle programme was the United States
government's manned launch vehicle programme,
administered by NASA from 1972 to 2011. Throughout
this time, the space shuttle launched for 135 missions. Each
mission lasted for one or two weeks. The space shuttle was
made of three main parts: the orbiter, the external tank
and the solid rocket boosters. It was launched like a rocket
but landed like a glider airplane.
The Buran spacecraft was a space shuttle developed
by the Soviet Union in response to NASA's space
shuttle programme. Since 2011, when the Space Shuttle
programme was retired, NASA has been entirely
dependent on Russia for transporting its astronauts to
and from the space station. In 2014, NASA had revealed
that Boeing and SpaceX will build America's first private
spacecraft to carry astronauts to and from the International
Space Station by 2017.
SOLID
ROCKET
fig: Launching of space shuttle
fig: Landing of space shuttle
Space Shuttle Disasters
Challenger Disaster: The space shuttle Challenger was NASA's second shuttle to reach
space, in April 1983. It successfully completed nine milestone missions. On its 10th
launch, on Jan. 28, 1986, the shuttle exploded 73 seconds after liftoff, killing the seven
crewmembers.
386
Science - 10
Ge o l o gy a nd A s t ro n o my
Columbia Disaster: On Feb. 1, 2003, space shuttle Columbia broke up as it returned to
Earth, killing the seven astronauts on board. It was the second space shuttle disaster
after the challenger disaster. The Columbia disaster directly led to the retirement of the
space shuttle fleet in 2011.
Some of the Major Space Missions to Planets/ Solar System
Since 1957 earth-orbiting satellites and robotic spacecraft journeying away from the earth
have gathered valuable data about the sun, earth, other bodies in the solar system and the
universe beyond. By the early 1970s orbiting communications and navigation satellites were
in everyday use, and the Mariner spacecraft was orbiting and mapping the surface of Mars.
By the end of the decade, the Voyager spacecraft had sent back detailed images of Jupiter and
Saturn, their rings, and their moons.
In 1980s satellite communications expanded to carry television programs, and people were
able to pick up the satellite signals on their home dish antennas. Satellites discovered an ozone
hole over Antarctica, pinpointed forest fires, and sent photographs of the nuclear power plant
disaster at Chernobyl in 1986. Space telescopes like Hubble Space Telescope(HST) have found
new stars. Their exploration gives us a new view of the galaxies in the universe.
Robotic spacecraft have landed on the moon, Venus, Mars, and the asteroid Eros. They have
visited the vicinity of all major planets, and flown by the nuclei of comets, including Halley’s
Comet. Scientists have used space-derived data to deepen human understanding of the origin
and evolution of galaxies, stars, planets, and other cosmological phenomena.
Astronomical Telescope
An astronomical telescope is an optical instrument which is used to see the magnified image
of distant heavenly bodies like stars, planets, satellites and galaxies etc. It is designed to gather
light rays as much as possible from the celestial bodies which helps to observe the fine details.
Types of Astronomical Telescope
There are two basic types of astronomical telescopes. They are refractors telescope and
reflectors telescope.
Refractor telescopes
Refractor telescope is a telescope that uses lenses and their ability to refract light rays to observe
and magnify distant objects. It uses two glass lenes. The large lens is the light gathering lens.
This lens is called the objective lens. The small lens is called eyepiece. This lens determines the
magnification of the telescope. Eyepiece is replaceable in most modern telescopes.
Advantages of refractor telescope
a.
Refractor telescopes are strongly made and its glass lenses need little to no maintenance.
b.
The glass surface inside the tube is sealed from the atmosphere so it rarely needs
cleaning.
c.
Air currents and effects due to changing temperatures in observation through a
refracting telescope are eliminated.
Ge o lo gy a nd A st ro n o my
Science - 10
387
Disadvantages of refractors telescope
a.
Different wavelengths of light are brought to focus at different points due to the glass
in the objective lens refracting the different wavelengths to different degrees. Due
to the wave nature of light, the longer
wavelength light is bent less than the
shorter wavelength light as it passes
through the lens. This effect is called
fig: chromatic aberration
chromatic aberration.
b.
The objective lens can be supported only at the ends. The glass lens will sag under its
own weight.
c.
It has very high initial cost relative to a reflector telescope.
Reflector telescopes
Reflecting telescopes use a curved mirror
(a parabolic mirror) to focus light onto a
second mirror, which is then sent to the
eye. A reflector telescope uses a mirror
as its objective. The mirror is close to the
rear of the telescope and light is reflected
Secooda,y mirror
Primary (objective) mirro
as it strikes the mirror. All celestial objects
fig: Reflector telescope
(including those in our solar system) are so
far away that all of the light rays coming from them reach the Earth as parallel rays. Since the
light rays are parallel to each other, the reflector telescope’s mirror has a parabolic shape. The
parabolic-shaped mirror focuses the parallel light rays to a single point.
Advantages of reflector telescope
a.
Mirrors in a reflecting telescope do not cause chromatic aberration. This is because all
wavelengths will reflect off the mirror in the same way.
b.
The objective mirror is supported all along the back side so they can be made very big too.
c.
Reflector telescopes are cheaper in comparison to refractor telescope of the same size.
Disadvantages of the reflector telescope
a.
Its mirrors need to be recoated every few years.
b.
A reflector telescope’s tube is open to the outside so its mirrors have to be cleaned
frequently.
c.
The secondary mirror is used to redirect the light into a more convenient viewing spot.
The secondary mirror and its supports can produce diffraction effects.
Uses of astronomical telescope
The purpose of a telescope is to:
Gather light: This is done by using a large aperture lens or mirror. Refractor telescopes gather
light based on the size of objective lens. The amount of light gathered in it depends on the area
of the lens used. The larger the objective the more light it gathers. This helps to resolve the
fine details.
0
388
Science - 10
Ge o l o gy a nd A s t ro n o my
Magnify the image: This is done by using a lens or mirror with a long focal length. Larger
telescopes can magnify more than 200x, making small objects like planets appear large enough
so we can see details on the surface.
Magnification of a telescope
The actual magnification of a telescope is given by the formula:
focal length of objective (F)
magnification =
focal length of the eyepiece (f)
Solved Numerical:
Calculate the magnification of a telescope with an objective of focal length 120 cm
using two different eyepieces each of focal length 20 mm and 10 mm.
Solution: Here, focal length of the objective lens (F)= 120 cm
focal length of the first eyepiece (f1) = 20 mm = 2cm
focal length of the second eyepiece (f2) = 10 mm = 1cm
Now, magnification for the first case = 120/₂ = 60x
Magnification for the second case = 120/1 =120x
Constellation
The small group of stars seen in the sky especially at night with fixed shape is called
constellation. We can see constellations in the northern and southern sky at night. The ancient
people of many civilizations named the constellations of northern and southern hemispheres.
They are named after characters from classical mythology and various common animals and
objects. Some examples of northern hemispheres constellations are Leo, Pisces, Ursa Major,
Cassiopeia, Andromeda, etc. and some examples of southern hemispheres constellations are
telescopian, Musca, Tucana, etc. There are 88 constellations covering the entire sky in the
northern and southern hemispheres. Out of 88 constellations, 12 constellations comprise the
zodiac sign.
On the basis of rotation of the earth and its axial tilt, stars and constellations are divided
into two groups as circumpolar constellations and seasonal constellation. Which stars and
constellations will be circumpolar and which will be seasonal depends on latitude of the earth.
The circumpolar constellations are a group of constellations that are always visible in the night
sky of the Northern Hemisphere or Southern Hemisphere. Some constellations can be seen
from both hemispheres but at difference watch time. They are seasonal constellations.
Constellation map helps to observe constellations in night sky. We can find the position of
pole star (Dhruva Tara) in northern sky. It is the brightest star in the northern night sky. Pole
star is directly above the North Pole on the axis of rotation of earth. So, all constellations
appear to revolve around the pole star which remains stationary throughout the year.
How to locate Pole star with the help of Ursa Major?
Pole star or Polaris (Dhurbatara, in Hindu mythology) is the closest star to the north
celestial pole. The other northern circumpolar constellations appear to revolve around
Polaris from east to west direction. It is the brightest star on the tail of Ursa Minor.
Ge o lo gy a nd A st ro n o my
Science - 10
0
389
The position of the pole star can be easily located with the help of the constellation Ursa Major.
To find Polaris, first find the Big Dipper. Imagine a line drawn connecting the right edge of
the "bowl" i.e. line in between Merak and Dubhe. If you extend the line north, it will come to
the brightest pole star.
Zodiac Constellations
When we observe in the clear sky from morning to the evening, the sun seems to move along a
certain path in the sky, from the eastern horizon to the western horizon. The path along which
the sun seems to move in the sky is called the ecliptic path or solar path. During the night,
when the constellations are visible, if we observe in the sky, we can see 13 constellations that are
along the solar path. Out of these 13 constellations, 12 of them have astrological significance.
These 12 constellations are called zodiacs. Zodiac or Rashi are the 12 constellations in the
sky that lie in the solar path and have certain astrological significance. The names of these 12
zodiac constellations are:
1. Aries
2. Taurus
3. Gemini
4. Cancer
5. Leo
6. Virgo
7. Libra
8. Scorpius
9. Sagittarius
10. Capricorn
11. Aquarius
12. Pisces
fig: Zodiac Constellations
In several religious practices, a born child is given a zodiac sign that is expected to determine
his/her fate. These signs are given according to the position of the stars. Stars change their
relative position in the sky and do not remain constant throughout the year. The determining
fate and so called luck on the basis of zodiac is a superstition and has no scientific grounds.
Circumpolar Constellations and Seasonal Constellation
On the basis of rotation of the earth and its axial tilt, constellations are divided into two groups
as circumpolar constellations and seasonal constellation.
Circumpolar Constellation
Constellations that never set below the horizon from the viewer's perspective are called
circumpolar constellation. Such constellations do not rise and set. They are visible all year
long from that hemisphere.
i. Northern hemisphere constellations.
Constellations that never set below the horizon from the viewer's perspective
in the northern hemisphere are called northern hemisphere constellations.
0
390
Science - 10
Ge o l o gy a nd A s t ro n o my
The five main northern circumpolar constellations are Ursa Major, Ursa Minor, Draco,
Cepheus and Cassiopeia. Northern hemisphere constellations appear to be revolving
around the pole star which remains stationary throughout the year.
Fact with reason
The pole star remains stationary throughout the year, why?
Pole star is straight above the North Pole on the axis of rotation of earth. So the pole
star remains stationary throughout the year.
ii. Southern hemisphere constellations.
Constellations that never set below the horizon from the viewer's perspective in the
southern hemisphere are called northern hemisphere constellations. Some examples of
southern hemispheres constellations are telescopian, Musca, Tucana, etc.
Seasonal constellations.
We can't see all the constellations every night of the year. This is due to both our position on
the earth (i.e. latitude) and revolution of the earth around the sun (i.e. the position of the sun
through the sky). The stars are always up in the sky. They are not visible to our eyes during
the day due to the brightness of the sun. In winter season and in summer season, the earth is
at two just opposite positions on its orbit. The part of the Milky Way which was observed in
night time in winter season crosses the sky during day time in the summer season.
A constellation that is only above the horizon for a part of the year and becomes visible seasonally
is called seasonal constellation. All constellations other than circumpolar constellations are
seasonal constellations. For example, winter constellations (Orion, Gemini, Taurus, etc.),
Spring Constellations (Cancer, Hydra, Leo, Virgo, etc.), Summer Constellation (Sagittarius,
Scorpius, Lyra, etc.), and autumn/fall constellation (Aquarius, Capricorn, Pisces, etc.) Some of
the constellations of one season cannot be seen in the other season at the same watch time from
the same place. Some constellations can be seen from both the hemispheres too but at different
watch time. It depends on how far is a person from the equator (i.e. latitude).
Fact with reason
Some of the constellations of one season cannot be seen in the other season, why?
The Earth with its inclined axis revolves round the sun from west to east. In winter
season and in summer season, the earth is at two just opposite positions on its orbit. This
is why some of the constellations of one season cannot be seen in the other season at the
same watch time from the same place.
Preparation of a model of Constellation
In model of constellations we create constellations pattern. When we construct the model, we
have to think of the positions of the zodiacal constellations compared with the positions of
the earth in its orbit. We will use the overhead projector to display the constellation pattern
on the cardboard (only the brightest stars). For making this model more understandable we
could paint the figures of mythological creatures onto the constellations freehand or using
transparencies. We can display constellation patterns on a wall to present this model as a twodimensional version. It could be more illustrative as a three-dimensional version in the middle
of the class.
Ge o lo gy a nd A st ro n o my
Science - 10
391
Another way to display constellation patterns is by letting the pupils be the parts of
constellation model, each carrying a cardboard of one constellation. In this model, we need
twelve constellations, one Earth and one Sun.
Activity: Draw all 12 seasonal constellation patterns separately on A4 sized papers.
Place them around your classroom. Use a basketball to model the sun in the center. Tell
your friend to rotate to experience day and night, and walk around the sun to model the
orbit throughout the year. Make them stop in different positions throughout the year,
and ask them which constellations they would be able to see at night.
Importance of observation of constellations in daily life
1.
The position of the constellation gives us an idea about time. Old people in village and
the remote areas still have an idea to find out time in the night by looking at the position
of the major constellations like Ursa Major (Saptarishi).
The constellations and their position change with seasons. We know about the seasonal
changes by looking at the position of the constellations. For example, when Orion starts
to become visible then it indicates winter is coming soon.
The constellations help in navigation. It is fairly easy to spot Polaris, the North Star. With
reference to this, other constellations can also be identified, which helps navigators to
travel across the globe.
Study of the constellations helps us to locate other heavenly bodies in the sky like the
position of the comets, meteors, etc.
Constellations have a religious value. Many cultures believe that the positions of
constellations are according to the God's will.
In the Hindu mythology, people use the constellations to give a zodiac sign, to make
birth record (Janam Patri or Janam Kundali in Nepali language), to forecast for good
2.
3.
4.
5.
6.
and bad omen (Grahadasha in Nepali language).
Planetarium
zenith
A planetarium is a theatre built primarily
for
presenting
educational
and
entertaining shows about astronomy
and the night sky, or for training in
celestial navigation. But instead of a big
cinema screen at the front of the room,
images are projected onto a domed
ceiling of a planetarium to create a more
immersive experience. A planetarium
can give us an amazing virtual tour of
fig: Components of planeterium
the universe from the earth. Shows of
both the fixed planetarium and mobile planetarium are a resource for astronomy information.
Mobile planetariums are constructed from a durable, wrinkle free and opaque fabric. It is
inflated with a high velocity industrial floor fan or a blower. The celestial scenes can be created
using a wide variety of technologies such as slide projector, video and full dome projector
systems and lasers. Following are the planetarium basics:
0
392
Science - 10
Ge o l o gy a nd A s t ro n o my
Dome: The dominant feature of a planetarium is the large dome. It is defined as the curved
surface or hemisphere where the projection is done. The main challenge while constructing a
planetarium projection dome screen is the echo of sound.
Auditorium: Planetariums have a large room, i.e. auditorium with a dome-shaped ceiling
and many seats built to receive the public during a show.
Projector: The most modern planetariums use digital projectors connected to computers.
They can project any image onto the dome to show incredible views from anywhere in the
universe. Combining data from space agencies, spacecraft and telescopes all over the world,
realistic graphical representations of entire galaxies can be projected onto the dome.
Computer and Software: Computers play the full dome content or scenarios through
software. Software with virtual model of the known universe is used for planetarium show.
A real-time astronomy software like Uniview brings scientific data to life in a planetarium.
Audio system: To ensure the most immersive environment in a modern digital planetarium,
audio system is uniquely engineered according to the dome size, tilt, seating configuration
and room acoustics. Loudspeaker reproduces the high frequencies of the sound signal and the
woofer reproduces the low frequencies of the sound signal.
Memory Plus
The term “planetarium” was initially used to represent a small model of the solar system.
The first planetarium was designed in the year 1682 by the famous astronomer Christiaan
Huygens.
B.P. Koirala Memorial Planetarium
B.P. Koirala Memorial Planetarium is in
Kiritipur, Kathmandu. It is established
to popularise the Science among the
students and general people. It will help
to conduct research activities in the area
of astronomy.
fig: B.P. Koirala Memorial Planetarium in Kiritipur, Kathmandu
Advantages of a Planetarium
Following are the advantages of a planetarium:
1.
Planetarium shows are a resource for astronomy information. It keeps people informed
about sky events.
2.
It helps to identify the stars and the changes in the position of stars and constellations
with seasons.
3.
A planetarium is the most effective teaching aid for astronomy in schools and colleges.
It is an educational device for showing the locations and movements of the planets and
other objects in the universe. Mobile planetariums for schools have made it easier for
students to understand astronomy.
4.
It is also used to create awareness about science and technology and space exploration.
Ge o lo gy a nd A st ro n o my
Science - 10
0
393
Answer writing skill
1.
Name the Russian space craft that put the first person into space.
Vostok
2.
Which was the first manned mission to land on the moon?
Apollo 11 was the first manned mission to land on the Moon.
3.
In northern hemisphere, Orion is visible on winter evenings but not summer evenings,
why?
In between the months of April and September, Orion will be in the daytime sky for the
people in northern hemisphere. But in winter and very early Spring it will be in the night
time and becomes visible to anyone in the Northern hemisphere.
4.
List any four importance of observation of constellations in daily life.
1. The position of constellation gives us an idea about time. Old people in village and
remote area still have an idea to identify time in night by looking at the position of the
major constellations like Ursa Major (Saptarishi).
2. Constellations and their position changes with seasons, which helps know about
seasonal changes. For example, when Orion started to becomes visible then it indicates
winter is coming soon.
3. Constellations help in navigation. It is fairly easy to spot Polaris, the North Star. With
reference to this, other constellations can also be identified. Which helps navigators to
travel across the globe.
4. Study of the constellations helps us to locate the other heavenly bodies in the sky like
the position of comets, meteors, etc.
5.
Explain in short about the space exploration and its benifits for mankind.
Since 1957 earth-orbiting satellites and robotic spacecraft journeying away from the
earth have gathered valuable data about the sun, earth, other bodies in the solar system
and the universe beyond. By the early 1970s orbiting communications and navigation
satellites were in everyday use. In 1980s satellite communications expanded to carry
television programs, and people were able to pick up the satellite signals on their home
dish antennas. Satellites discovered an ozone hole over Antarctica, pinpointed forest
fires,, etc. Communications satellites help the world stay connected. The technologies
developed with space exploration are beneficial for the contemporary world.
0
394
Science - 10
Ge o l o gy a nd A s t ro n o my
Exercise
Step
A.
1
Very Short Answer Questions
1.
What is a constellation?
2.
How many constellations are known to us?
3.
Name any four constellations.
4.
What is meant by space exploration?
5.
Who is the father of modern astronautics?
6.
What is an artificial satellite?
7.
What is spacecraft?
8.
What is a robotic spacecraft?
9.
What is a space probe?
10. Name the followings:
a. The first satellite
b. The first animal in space
c. The first human being to travel into space
d. The first human being on
the moon
11. What is an astronimcal telescope?
12. What is a planetarium?
Step
B.
2
Short Answer Questions
1.
Write in short about
a. International Space Station (ISS)
b. Space Shuttle
2.
Write the advantages of a planetarium.
3.
Give two advantages of each refracting telescope and reflecting telescope.
4.
Give two disadvantages of each refracting telescope and reflecting telescope.
Ge o lo gy a nd A st ro n o my
Science - 10
395
C.
D.
Give Reasons
1.
Many space missions are more suited to robotic spacecraft than the crewed
operation.
2.
A planetarium is made with a dome structure design.
3.
some of the constellations of one season cannot be seen in the other season
4.
Pole star remains stationary throughout the year.
Write Differences
1.
Galaxy and constellation
2.
Reflecting telescope and refracting telescope
3.
Northern hemisphere constellations and Southern hemisphere constellations.
Step
3
1.
Mention the importance of constellations in our daily life.
2.
Write in short about history of space exploration.
3.
Write three benefits of space explorations for the mankind.
4.
Write in short about any three components of a planetarium.
Step
4
5.
Present your view on the need of movable planetarium in schools.
6.
Explain in short about some of the major space missions to planets.
7.
How does an astronomical telescope work? Explain.
8.
Mention the uses of an astronomical telescope.
9.
How do you prepare a model of constellation? Explain.
Project Work
Make a table on a chart paper and note down about the space exploration missions and
present it in the classroom.
396
Science - 10
Ge o l o gy a nd A s t ro n o my
0
You can add this document to your study collection(s)
Sign in Available only to authorized usersYou can add this document to your saved list
Sign in Available only to authorized users(For complaints, use another form )