ALARM COMMANDS BCF/BTS:
Command
Command Description
Syntax
ZEEI
O/P OF BCF STATUS
ZEEI:BCF=X;
ZEEI
O/P OF BTS STATUS
ZEEI:BTS=X;
ZEOL
CHECKING OF ACTIVE ALARMS
ZEOL:X;
ZEOH
CHECKING OF ALARM HISTORY
ZEOH:YYYY-MM-DD,HH:BCF=X;
ZAHO
CHECKING OF BSC ACTIVE
ALARMS
ZAHO;
ZACA
ALARM CANCELLATION OF BSC
ZACA:ALARMNUMBER;
ZEFO
FOR ALARM POLARITY
ZEFO:23:IOP;
ZEFM
ZEFX
ZEFX
ZEFM:X (BCF):BBU=NONE, NTIM=A
(minutes), BTIM=B (minutes);
ZEFX:X (BCF NO):INBR=Y (Alarm
To Route Mains On P1 Message
No):ROU=MAINS;
ZEFX:X (BCF NO):INBR=Y (Alarm
To change alarm Polarity (Open/Closed)
No):POL=OPEN/CLOSED
Intelligence Shutdown (HUB).
ALARM NUMBERS:
Alarm No
Description
O&M Link Failure
QUALITY ALARMS:
7706
ERxx DDU module has detected
VSWR above major limit
7705
LAPD Failure
7995
Power battery Backup
7404
Low System Voltage
7601
BCF Operation Degraded
7604
BTS Operation Degraded
7607
TRX Operation Degraded
Alarm No
Description
Power battery Backup
7995
O&M Link Failure
7706
BCCH Missing
7767
LAPD Failure
7705
Trx Faulty
7606
Trx Restarted
7708
7710
LOCK/ UNLOCK of Object
7725
Traffic Channel Activation Failure
CH Congestion
7746
Channel Failure Rate
7745
Mean Holding Time
7743
PCM Failure
7704
7738
BTS With No Transactions (Zero Calls Issue)
RESET COMMANDS:
Command
Command Description
Syntax
ZEWO
To Check software version on Site
ZEWO;
ZEWV
Soft Reset of Site
ZEWV:X:BU/NW/FB
ZEFR
RESET OF WHOLE SITE
ZEFR:X:SITE;
ZEFR
RESET OF OMU
ZEFR:X:OMU;
ZUSC
RESTART OF ET
ZUSC:X;
ZUSI
TO RESET ET, AFTER IT ALSO
RESET SITE
ZUSU:ET,#:C=TOT; …
ZUSI:ET,X:B / U;
ZDTC
RESETTING LAPD
ZDTC:LAPD NAME:STATUS
ZUSU
TO HARD RESET TCSM
ZUSU:TCSM,(TCSM#):C=TOT;
ZEFS
LOCK/UNLOCK OF BCF
ZEFS:X:L/U;
ZEQS
BTS LOCK/UNLOCK(SECTOR)
ZEQS:BTS=X:L/U;
ZERS
TRX LOCK/UNLOCK(TRX)
ZERS:BTS=X,TRX=Y:L/U;
ZDDS
TO SEE THE STEPS WHILE THE
RESET OF SITE
ZDDS;
PDC
AFTER EXCECUTION OD ZDDS
PDC :BCF#
ET COMMANDS:
Command
Command Description
Syntax
ZAHO
CHECKING OF BSC ET ALARMS
ZAHO:ET,X;
ZAHP
ALARM HISTORY OF BSC ET
ALARMS
ZAHP:ET,X::YYYY-MM-DD;
ZAHP::NR=ALARM#;
ZUSI
CHECKING OF ET STATUS
ZUSI:ET,X;
ZYMO
CHECKING THE CURRENT
STATUS OF ET
ZYMO:ET,ET#;
ZEEL
BLOCKED TRX
ZEEL:BL-TRX; / BL-RSL /BL-RSL;
ZUBS
TRX TESTING
ZUBS: BTS=BTS#, TRX=TRX#;
ZUBP
TRX TEST REPORT
ZUBP:TR:BTS=BTS#,TRX=TRX#;
ZRCI
TO CHECK THE STATUS OF ET
ZRCI:SEA=4:ETPCM=(ET#),CRCT=
1-1&&-31;
Command
Command Description
Syntax
ZERO
CHECK TIMESLOT MISMATCH AT
BSC & BTS
ZERO:BCF/BTS/TRX:XXX;
ZEQS
BTS WITH NO TRANSACTIONS
ZEQS:BTS=X:L:FHO,10;
ZQLI
TO CHECK THE BSC LINKAGE
DATA
ZQLI;
ZEEL
STATUS OF BLOCKED SITES
ZEEL:BL;……ZEEL:BL-USR;
ZEEL
TRAFFIC CHECKING ON BSC
ZEEL;
Command
Command Description
Syntax
ZDTF
TO CHECK THE STATUS OF
LAPDs on TCSM
ZDTF:TCSM;
ZDTI
CHECKING STATUS OF LAPD
ZDTI:::PCM=(PCM NUMBER);
ZDTC
TO CHANGE STATUS OF LAPD
ZDTC:X:WO/BL/AL/BL;
(X=NAME FROM ZTDI
COMMAND)
BSC/BTS:
LAPD:
ATER:
Command
Command Description
Syntax
ZUSI
TO CHECK WHETHER ATER IS
OPERATIONAL
ZUSI:TCSM;
ZUSI
CHECK STATUS OF
ZUSI:COMP;
ZCET
TO CHECK TRAFFIC ON ATER
ZCET:ETPCM=(ET#),CRCT=(TIME
SLOT#)-1&&-31;
ZYMO
CHECKING THE ATER STATUS
ZYMO;
Command
Command Description
Syntax
ZFWO
CHECKING GPRS/NSVC STATUS
ZFWO:BCSU=0&&6;
TO CHECK THE STATUS OF GPRS
ON BTS OF ANY SITE
Enable/Disable EDGE/GPRS (First
Lock Sector)
ZEQO:SEG=X:GPRS:; OR
ZEQO:BTS=X:GPRS:; (X=BTS NO)
ZEQV:SEG=X:GENA=Y/N; OR
ZEQV:BTS=X:EGENA=Y/N;
ZFWO
GPRS STATUS
ZFWO:BCSU=0&&6;
ZFUI
TO CHECK THE GPRS ET
ZFUI;
Command
Command Description
Syntax
ZDDS
Service Terminal Dialogue
ZDDS;
ZNEL
CHECKING SS7 LINKS STATUS
ZNEL;
GPRS/ EDGE:
ZEQO
ZEQV
OTHER COMMANDS:
ZQRL
ZDTT
ZQWI
GIVES THE IP ADDRESS OF
NETACT ROUTER
TO CHANGE THE STATUS OF
TCSM
ZQRL;
ZDTT:TCSM,(TCSM#):BL/WO;
TO SEE QUEUE
Notes:
If site is in reset. Then:
1.
2.
3.
4.
Execute command ZDDS; PDC:BCF #;
If there is alarms 255 (DAP), then check BCCH TRX’s. DAP is enabled at BCCH TRX’s.
Disable GPRS/ EDGE on BCCH Sectors (First Lock Sector).
Soft rest site using ZEQV.
ZNRI:NA1;
ZNEL
ZEQO:BTS=24:MIS;
ZEEL::BTS=60;
ZEQO:BTS=24:INT:;