TEMS™ Pocket 24.0 Release Notes
1 About This Document
This document contains the release notes for all TEMS Pocket 24.x releases.
© Infovista Sweden AB 2022. All rights reserved.
TEMS™ is a trademark of Infovista. All other trademarks are the property of their respective holders.
2 Installation and Upgrading
To install TEMS Pocket 24.x on a device, please follow the instructions in the TEMS Pocket 24.x Installation
Guide.
Note: Always reboot your device after installing or upgrading TEMS Pocket.
3
L3 decoding updates
Work has been done to upgrade the 3GPP layer 3 decoding to release 16. The following specifications are now
based on the latest rel-16 versions (2021-12):
•
•
•
•
•
24.501 (5G-NAS)
38.331 (NR-RRC)
24.301 (LTE-NAS)
36.331 (LTE-RRC)
24.008 (UMTS-NAS)
www.infovista.com | 1
4 TEMS Pocket 24.0
5 New Devices
6 Samsung Galaxy S21 FE SM-G990B
New Samsung 5G devices are added. Qualcomm chipset-based and run Android 11. Similar specifications but
different band capabilities depending on market/region.
Specifications*:
Control functions:
•
•
•
•
Lock on RAT (NR/LTE/WCDMA/GSM)
Lock on Band (/NR/LTE/WCDMA/GSM)
Lock on PCI (Physical Layer Cell ID)
Lock on UARFCN
Frequency bands:
•
4G bands
1, 2, 3, 4, 5, 7, 8, 12, 17, 20, 26, 28, 32, 38, 40, 41, 46, 66
•
•
5G bands
1, 3, 5, 7, 8, 20, 28, 38, 40, 41, 66, 78 SA/NSA/Sub6
2G bands
GSM 850 / 900 / 1800 / 1900
•
3G bands
HSDPA 800 / 850 / 900 / 1700(AWS) / 1900 / 2100
•
Speed
HSPA 42.2/5.76 Mbps, LTE-A (CA) Cat18 1200/150 Mbps, 5G
Throughput capabilities:
•
•
•
•
•
NR (New Radio) Non-Standalone and Standalone mode
LTE Category 20/13 capable (Up to DL: 2.0 Gbit/s, UL: 150 Mbit/s)
HSDPA Category 24 (42.2 Mbit/s), HSUPA Category 6 (5.76 Mbit/s)
4x4 MIMO
VoLTE/VoWiFi
Modulation:
•
•
DL: 256QAM
UL: 256QAM
Google Android 11
WLAN 802.11a/b/g/n/ac (2.4 and 5 GHz)
Chipset/CPU:
•
Qualcomm SM7125 Snapdragon 720G (8 nm)
www.infovista.com | 2
* Depending on network and SIM. The device radio settings are reconfigured every time a new SIM card is
inserted to the phone, therefore, you need to test in the specific network to obtain a correct value for band support
and capabilities.
7 Samsung Galaxy S22 Series SM-S901/906/908/ (B/U/U1/W/E/N/0)
Samsung 5G devices added. (U/U1/W/E/N/0) Qualcomm chipset-based and B models Exynos chipset based.
Run on Android 12. Band capabilities can differ depending on market/region.
Note:
Audio Quality Measurements not possible in this first release. (POLQA and SQLEAR)
Specifications*:
Control functions:
•
•
•
•
Lock on RAT (NR/LTE/WCDMA/GSM)
Lock on Band (NR/LTE/WCDMA/GSM)
Lock on PCI (Physical Layer Cell ID)
Lock on UARFCN
Frequency bands:
•
4G bands
1, 2, 3, 4, 5, 7, 8, 12, 17, 20, 26, 28, 32, 38, 40, 41, 46, 66
•
•
5G bands
1, 3, 5, 7, 8, 20, 28, 38, 40, 41, 66, 78 SA/NSA/Sub6
2G bands
GSM 850 / 900 / 1800 / 1900
•
3G bands
HSDPA 850 / 900 / 1700(AWS) / 1900 / 2100
•
UMTS: B1(2100), B2(1900), B4(AWS), B5(850), B8(900)
Speed
HSPA 42.2/5.76 Mbps, LTE-A (CA) Cat18 1200/150 Mbps, 5G
Throughput capabilities:
•
•
•
•
•
NR (New Radio) Non-Standalone and Standalone mode
LTE Category 20/13 capable (Up to DL: 2.0 Gbit/s, UL: 150 Mbit/s)
HSDPA Category 24 (42.2 Mbit/s), HSUPA Category 6 (5.76 Mbit/s)
4x4 MIMO
VoLTE/VoWiFi
Modulation:
•
•
DL: 256QAM
UL: 256QAM
Google Android 11
WLAN 802.11a/b/g/n/ac (2.4 and 5 GHz)
Wi-Fi 6 (up to 1.5 Gbit/s)
Chipset/CPU:
www.infovista.com | 3
•
Qualcomm SM7325 Snapdragon 778G 5G (6 nm)
* Depending on network and SIM. The device radio settings are reconfigured every time a new SIM card is
inserted to the phone, therefore, you need to test in the specific network to obtain a correct value for band
support and capabilities
8 New Features
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Backpack solution GPS enhancements (USB GPS with CPU to Backpack agents/remote)
Support for Raw/refined logfile recording (Reduce logfile size)
- Events and Information Elements for Ping and HTTP action are included in refined recordings.
ODM Ping capabilities enhancement
Android 12 support on Samsung S21 SM-G99x U/B with TEMS Pocket Pro
RAT lock NR Technology
Qualcomm - Lock to both LTE and NR band when performing LTE/NR RAT lock
Support of MXflex scanner in TEMS Pocket Professional
SQLEAR ODM Support
IPCapture on commercial Android devices
Android 12 support for OnePlus, Xiaomi and Sony devices
Report Radio Channel And BSIC Info To Fleet
Higher Frequency Of Radio Parameter Logging For Reporting To Fleet
Report UE TxPower to Fleet
Device RAT/band control function lock status information added to logfile
Quick support diagnostics collection option
Device thermal throttling indication
New top view for 5G SA information
USB GPS - Fallback solution when external GPS lost
9 Corrected Bugs
367374:
372232:
289861:
457814:
140128:
386350:
465314:
460177:
384227:
367939:
465411:
473628:
Pocket freezes using Sara RM-410 connected to SM-G988B A11
P40 TEMS Pocket Problems TP crash when open it and could not see professional mode in use.
Add $IMEI$ and other variables to be used as logfile name prefix for Manual recording in TP 23.x
Data Throughput View not refreshing properly
Iperf Progress- throughput value wrong
TEMS Pocket logfile GSM coverage plot in TI issue
When receiving SMS while running FTP UL testing, TP's application layer occur not defined in TI
and TD
Cell id in Hex in not appearing in TEMS pocket
Pocket API SRS - Lock status for WCDMA and GSM doesn't work
TP 23.3 is not showing 5G parameters without recording log file in G998B
Route And Area kml Disappearing When Panning / Zooming with HERE Map
TP Logfile upload functions behavior
10 Removed Features
•
HTTP Internal Client Type removed as an option. All scripts containing HTTP Internal action must be
updated before executed in TEMS Pocket 24.0.
www.infovista.com | 4
11 Deprecated Functions
The below listed functions are deprecated functions and will be removed in a future release.
•
Android 10 support
12 Device support
These tables show device support at the release date for the latest version of TEMS Pocket.
Introduced
End of
Supported devices
in version
Maintenance
Huawei P40, Mate 40
TP23.0
2022-06
OnePlus 8 5G IN2011, IN2013, IN2017
TP22.1.1
2021-09
OnePlus 8T 5G
TP23.0
2022-06
✓
✓
OnePlus 9 / 9 Pro
Samsung Galaxy S22 series 5G SM-S90*B/U/U1/W/E/N/0
Samsung Galaxy S21 FE SM-G990B
TP23.1
TP24.0
TP24.0
2022-09
Samsung Note20/Note20 Ultra 5G SM-N981U/W/SM-N986U
TP22.2
2021-09
Samsung Note20/Note20 Ultra 5G SM-N981U1
TP23.1
2021-09
Samsung Note20/Note20 Ultra 5G SM-N9860
TP22.3
2022-02
✓
Samsung Galaxy S21 series 5G SM-G99*B/U/U1/W
TP23.0
2022-06
✓
TP22.0.1
2021-06
✓
Samsung Galaxy S20+ 5G SC-52A/SC-G02
TP22.2
2021-09
✓
Sony Xperia Pro
TP23.0
2022-06
✓
TP22.1.1
2021-09
✓
Samsung Galaxy S20+ 5G SM-G986B/U
Sony Xperia 1 (mark II)
Sony Xperia 1 (mark III)
Xiaomi Mi 10 Pro 5G M2001J2G
TP22.2
TP23.1
Exelonix LPWAN USB
Exelonix R410m
✓
✓
2021-09
2022-09
Introduced
in version
TP 23.3
TP 21.2
Supported IoT devices
Supported Android versions1:
✓
TP23.2
Xiaomi Mi 11
1
Fully
verified
✓
End of
Maintenance
2020-11
10, 11, 12
TEMS Pocket can be installed on all supported devices with TEMS firmware based one of these Android versions.
www.infovista.com | 5
www.infovista.com | 6
13 Known Bugs and Limitations
14 TEMS Pocket Application Related
•
Commercial Android12 devices may experience issues running TEMS Pocket due to Battery saving
features.
•
In a Controller/Agent setup using BT as bearer, GPS location sharing is only active when script is being
executed.
•
All old scripts with Internal HTTP Internal action need to be updated manually to use either OnDevice
Browser or OnDevice File.
•
Audio Quality Measurements on Samsung S22 series devices not possible in this first release.
(POLQA and SQLEAR)
•
Automatic Pinpointing does not work on newer device FW’s, mainly seen on Android 12.
•
Samsung Galaxy Fold 3 (SM-F926B), Pocket should be started when device is folded to get correct view
configuration when unfolded. Also lock the device in portrait mode.
•
Only Scan Status Overview is updated on Controller when using a scanner connected to Agent.
No detailed scan information is shown on the Controller, but all values are present in the logfiles.
•
Long startup time for update of views on Controller when using BT connection.
•
WCDMA Cell Lock limitation: To unlock a combined RAT and cell lock on WCDMA correctly, the
unlocking must be done in two separate control function actions. The first should unlock WCDMA cell
lock, and the second should unlock WCDMA RAT lock.
•
The first time after an installation you need to start the app SeeGull Connect and accept the “DISABLE
BATTERY OPIMIZATION”.
•
When scanning on NB-IoT no other scan mode is allowed.
•
When NR scanning is performed a dedicated device need to be used without using simultaneous Data
actions.
•
Cell files are only supported in Cell List views when using the Legacy decoder.
•
All Pocket devices must be connected to an internet connection at first restart after the Pocket
installation, and then at least once a week to receive updates and allow license synchronization.
•
It is recommended to use a Samsung Galaxy Tab7 tablet with an active SIM-card as the controller in a
Controller/Agent setup.
•
When performing automatic pinpointing in a Controller/Agent setup, it is not possible to pan the map and
set manual pinpoints. To recover if the location is lost, cover the camera to trigger the correction
pinpoint.
•
NR Values are not cleared correctly on Samsung chipset-based devices.
•
Android Location must be enabled on devices running Android 10 or later to be able to use the SeeGull
Connect App.
•
For devices running Android 10 or later, users need to manually grant permission to Send and Receive
SMS for the OnDeviceSmsService application
•
Events are not updated correctly when running YouTube PEVQ-S testing.
www.infovista.com | 7
•
When the device is on GSM, the application layer throughput displayed during HTTP and FTP sessions
might dip periodically. The average throughput, however, is not affected and is calculated correctly.
•
When executing several HTTP Get actions in a row, the timestamp of the first data report of one action
may sometimes actually be identical with the timestamp of the last data report from the previous action.
This can occur for FTP as well.
•
TEMS Pocket may generate duplicated SIP call events if retransmissions occur.
•
The Wi-Fi function in TEMS Pocket does not distinguish between 20 MHz and 40 MHz bandwidth
measurements. All channels will be displayed as 20 MHz channels.
•
5 GHz Wi-Fi cells are not shown in the Spectrum view.
•
In a controller/agent setup, all agents must have the same TEMS Pocket version as the controller. If they
do not, the controller will not connect them.
•
During logfile replay, when rewinding, or fast-forwarding more than 60 seconds, the event markers in line
charts and maps will be incorrect or missing. To get accurate event markers, replay the logfile from
beginning to end.
•
When stopping a script with control functions on a device with the Samsung Exynos chipset, all control
functions are set to default and needs to be enabled manually again.
•
If TEMS Pocket UI is restarted during pinpointing, the pin-pointing session must be restarted.
•
TEMS Pocket does not support the use of dual SIM cards. Only SIM slot 1 is supported.
•
When making a voice call with TEMS Pocket, a dialog to select dialing service may appear. You must
select “Phone” and “Always” to ensure correct functionality in TEMS Pocket.
•
It is recommended to avoid extremely large map sets while performing indoor measurements since it
may sometimes result in log files that cannot be read in post-processing tools.
•
TEMS Pocket presently does not support IPsec encryption algorithm des-ede3-cbc on devices using the
Samsung Exynos chipset.
•
Page switching in the LTE Cell Configuration view may not work after startup. Switching to another
category and back to the Idle category enables the functionality.
•
The time display while replaying a logfile, can sometimes show the wrong value. Drag the control back to
start of the playback to resolve the time display issue.
•
Using the Remote-Control feature in TEMS Director while running tests in TEMS Pocket will impact
logfile size because the IP traffic generated by the live stream will be recorded to the logfile.
•
The maximum Response Timeout setting for ODM SynchPoint is 60 seconds. If a value above that is
set, it will be handled as 60 seconds.
•
In a multi-device configuration, if you switch off Bluetooth on the Controller when several Agents are
connected, the Controller application may restart
•
In a multi-device configuration, for pinpointing:
o
Set the Map Set Floor Sync option in the Controller Settings to Enabled
o
In this mode the Controller will only sync the selected floor plan in the Map Set with the selected
Agent
o
The largest Map Set floor plan that you can load is 2MB
www.infovista.com | 8
•
It is not possible to perform Facebook Post photo operation.
•
It is not possible to replay logfiles with 5G NR scanning data.
•
NR Layer 3 messages will not be decoded or displayed in the L3 Message view.
•
If the devices go into No Service when synchronizing to TEMS Director Fleet, any active measurements
will be paused and restarted when the device gets into service again.
15 Third-party Data Related
•
If two or more cells within the same iBwave transmitter file (for the same floor) share the exact same channel
(GSM: BCCH ARFCN; WCDMA: UARFCN; LTE: EARFCN; CDMA: RF Channel) and code (GSM: BSIC;
WCDMA: scrambling code; LTE: PCI; CDMA: PN), then TEMS Pocket cannot distinguish between these cells
and therefore cannot present them by name.
16 Device Hardware Related
•
Commercial devices with SM-G986W & 996W chipset does not Hang-up using Wi-Fi calls. It is
recommended to disable Wi-Fi Calling in Android menu.
•
There are currently no supported devices able to perform the Cell Prevent control function even though it is
visible in the TEMS Pocket menu.
•
ARFCN Lock do not work on the Samsung Galaxy SM-G986W running Android 11.
•
Devices running intense data testing in high throughput environments may experience CPU thermal
Throttling. To reduce the risk of this happening add wait actions between data actions in scripts (We
recommend a maximum of 10 seconds data transfer, then 20 seconds wait until next action. This may vary
depending on device model, network performance, and ambient temperature).
•
PCTEL scanners may lose USB connection when in idle mode, therefore it is recommended to disconnect
and reconnect the USB cable just before starting tests with TEMS Pocket.
•
It is not possible to perform video quality testing using the PEVQ-S algorithm on the OnePlus 8 5G.
•
The Samsung Galaxy S20+ SM-G986U has a configurable navigation bar in the bottommost part of the
screen that may cover parts of the TEMS Pocket UI. Please refer to the TEMS Pocket User Manual for
instructions on how to avoid the problem.
•
PEVQ-S video quality testing on the Samsung Galaxy S20 SM-G986B and the OnePlus 8 (IN2011, IN2013,
IN2017) will fail.
•
In a multi-device (controller:agent) configuration, the Agent Configuration view displays the Agent ID
incorrectly, e.g. 02:00:00:00:00:00. The Agent Name is displayed correctly.
•
GPS signaling can cease during testing on OnePlus devices. If it happens, please restart the device.
•
Logfile replay control buttons can be hidden behind the bottom device buttons on the Google Pixel 3.
Restarting TEMS Pocket will solve the issue.
•
To apply an LTE EARFCN lock, LTE RAT lock must always be applied first.
•
To apply an LTE EARFCN lock from TEMS Director Fleet, use the CellLockLTE activity.
www.infovista.com | 9
17 Important Information
If you get a 404 error when you try to access the online User's Manual, Quick Guide or Release Note from TEMS
Pocket, you need to clear the application cache:
1. Launch the device's Settings app
2. Tap Apps (or Applications) > TEMS Pocket UI > Storage
3. Tap the Clear Cache button
4. Close the Settings app
5. Restart TEMS Pocket
18 Contact Information
Please visit www.infovista.com for customer support contact information.
www.infovista.com | 10