General Moshell Commands (Applicable for RBS, RNC, MGw) IP Address ifconfig Ping if get destination inaccessable or host unreachable – most likely Transmission if Request Timed Out – most likely Node B problem if TTL Expired in Transit – Loopback somewhere in Transmission Unable to moshell pglist –e lhsh 001200 pglist –e pgkill <handle> (rbs) (rnc) check c drive on rbs should be 10 directories P2.1.6 otherwise rebuild ls –l /c Alarms al ala alt alk Logs lga (Alarm log) CV’s cvcu cvls cvmk <cv name> cvset <cv name> cvms <cv name> cv help Cabinet Info cab cabx cabl cabd cabxlsd Board Status To check the Admin and Operational status of the boards lt plug lst plug To Block a board bl <proxy number of board> To Deblock a board deb <proxy number of board> To restart the entire node restartObj me or actc 0 restart To check when the node has recovered from restart pol lt root (to clear all proxy’s) RBS INFO check volumes etc cabx lhsh 000800 vols lhsh 000900 vols cabd How to tell if 3101 or 3202 or 3206 get 0 actions you can perform note same as restartObj me actl 0 No of calls setup (radio links) lt radio get radio num The number of radio links should not be 0 if calls are active or being attempted on the rbs. From RNC lt utrancell get utran erdl (MaxTxPowerDl) VSWR te –p 010600/port_0_dev_22 e all tmaCdciProcess 010900 011200 te –p 010600 log read or lhsh 010600/port_0_dev_18 asc vswr To see ASC and RET info lt sector lc sector lcc sector lst sector To see PSU’s in PCU lt pcu lcc pcu st lt power lcc power st get psdevice Sometimes only 3 PSU in situ but data configured for 6. If the case you will get the following alarm PowerSupplySystem-RejectSignalFromHardware message_not_expected it is possible that a PSU is faulty. Volumes Full lhsh xxxxxx vols lhsh xxxxxx ls /f/dp_loadmodules lhsh xxxxxx format –f /f lhsh xxxxxx reload (check what is loaded) (format f drive) (reloads wanted progs to f drive from GPB) RBS Capacity lt commcontext get <proxy> number of commcontexts = number of channel elements used lt UplinkBaseBandPool pget <proxy> gives latest rop for rax capacity , number of calls and type and failures If you suspect H/W capacity issue call NSS to activate traces and investigate Spreading Factors Speech 12.2Kbs 64k/64k data 64K/128K data 64K/384K data Video 64K CS Streaming 57K CS Broadcast Paging UL DL sf64 sf16 sf16 sf16 sf16 sf16 sf128 sf32 sf16 sf8 sf32 sf32 sf256 sf128 Measuring Aal2 Congestion lt aal2ap pget <proxy> Aal2Sp=1,Aal2Ap=1 Aal2Sp=1,Aal2Ap=1 Aal2Sp=1,Aal2Ap=1 Aal2Sp=1,Aal2Ap=1 Aal2Sp=1,Aal2Ap=1 Aal2Sp=1,Aal2Ap=1 Aal2Sp=1,Aal2Ap=1 Aal2Sp=1,Aal2Ap=1 Aal2Sp=1,Aal2Ap=1 Aal2Sp=1,Aal2Ap=1 Aal2Sp=1,Aal2Ap=1 pmExisOrigConns 0 pmExisTermConns 16 pmExisTransConns 0 pmSuccInConnsRemote 193052 pmSuccOutConnsRemote 0 pmUnRecMessages 0 pmUnRecParams 0 pmUnSuccInConnsLocal 0 pmUnSuccInConnsRemote 0 pmUnSuccOutConnsLocal 0 pmUnSuccOutConnsRemote 0 Check pmUnSuccInConnsLocal Number of unsuccessful attempts to allocate Common Part Sublayer, CPS, resources during establishment of incoming connections on this AP caused by Channel Identifier, CID, and/or bandwidth collision or mismatch of Call Admission Control, CAC, between peers. Check pmUnSuccInConnsRemote Number of unsuccessful establishment of incoming connections on this AP caused by reject from beyond this node Check pmUnSuccOutConnsLocal Number of unsuccessful attempts to allocate CPS resources during establishment of outgoing connections on this AP. Caused by rejects in CAC (Connections Admission Control). Main indicator of aal2 congestion problems , increase traffic descriptor or another E1 required. Check pmUnSuccOutConnsRemote Number of unsuccessful establishment of outgoing connections on this AP caused by reject from remote side, reset from remote side, no reply or signalling link failure. RAXB R2 ladder for mapping RAB’s to number of CE There is a new ladder for RAXB R2 as shown in the table below. For 64 Kbps data twice the amount of c.e is required. This new ladder only have a small impact when dimensioning a network, as most of the data traffic is downlink and also with higher bitrates than in uplink. Even with the new ladder Ericsson have higher channel element efficiency than competition. Ericsson channel element implementation in the uplink is matched with competition. The channel element implementation in downlink for higher data rates is up to 50% more efficient than competition. Service RAXB R1 (UL) RAXB R2 (UL) TXB R1 (TXB board in the DL is not changed for RBS R2) 12,2 kbps speech 1 1 1 32 Kbps CS or PS 1 2 1 64 Kbps CS or PS 2 4 2 128 Kbps CS or PS * * 4 384 Kbps CS or PS * * 8 *) Not used in P2.1 RBS Synching up te log read | grep –i clock nodesynch 1 after 5 mins nodesynch 2 2-3 mins after above nodesynch 3 5 mins after above Site comes up 10 mins after nodesynch 3 Sector on which RAX lt prach lget prach DownLink OK Uplink Not OK Check ETM1 in RBS for the following lhsh 000200 te log read [2005-04-12 01:47:44.300] Sys_Spas_hwdrv_proc spicfunc.c:2736 INFO:SAI Egress Discard. cells (port-queue): (63-2) [2005-04-12 01:47:45.304] Sys_Spas_hwdrv_proc spicfunc.c:2736 INFO:SAI Egress Discard. cells (port-queue): (63-2) [2005-04-12 01:47:46.308] Sys_Spas_hwdrv_proc spicfunc.c:2736 INFO:SAI Egress Discard. cells (port-queue): (63-2) Also check the ETM1 in the RXI for the above ,also check if any other RBS on this ETM1 are experiencing the same problem. eg lhsh 001600 te log read Format the flash f drive and restart the board lhsh xxyyzz format –f /f lhsh xxyyzz reload RNC INFO RNC Module 1 2 3 4 5 6 7 8 9 10 11 12 001400 011300 011400 011500 021300 021400 021500 001600 011200 011700 021200 021700 Redundant (MS) Slot14 (ES1) Slot13 (ES1) Slot14 (ES1) Slot15 (ES2) Slot13 (ES2) Slot14 (ES2) Slot15 (MS) Slot16 (ES1) Slot12 (ES1) Slot17 (ES2) Slot12 (ES2) Slot17 Slot15 Slot16 Slot16 Slot16 Slot16 Slot16 Slot16 Slot15 Slot16 Slot16 Slot16 Slot16 To block all cells in RNC to force people to roam before blocking check cells already blocked lt ^utrancell st utrancell dis (make a note of these) bl utrancell When problem fixed deblock all cells deb ^utrancell bl <utrancells that were blocked b4) Common RBS Problems Nbap Common down – block and deblock proxys lt nbap|^utranc lc <utrancell> lst <utrancell> lst <iublink id> Nbap Dedicated down – Restart ETB in rbs Cell down – block deblock proxy’s Rach , Fach, Pch – block deblock proxy’s To block a sector bl <proxy of sector to be blocked> deb <proxy of sector to be deblocked> To block entire RBS lbl <utrancell> To deblock entire RBS ldeb <utrancell> CV's cvcu cvls cvms egralyn correct maxtxpowerdl cv cu cv ls cv help Utrancell state availability str str1 str2 st utrancell dis|\(lo) To find ip address ifconfig Restart logs Lgo – to print out llog llog -l llog -l 3 all llog Board Info cabx cabl cabxlsd Signal Links in MGW lt mtp3b lst mtp3b get <proxy> acl <proxy> acc <proxy> Call Disconnected by UE and not Utran If the UE disconnects the call with interworking unspecified , look in the NAS setup message sent from the CN to the UE. this can help to located the problem in the core. Especially low layer compatability component of Setup message. If possible compare to a good call. Command from RNC or GNNCC java commands LOAD Starting Commands lt utrancell|nbap|aal|etm lt all :/opt/ericsson/cominf/Netscape_TRE_131_09 : ehassha@ri3guas1> cd ./moshell ehassha@ri3guas1>./moshell 3rj01 ( 3rj01- RNC) : Load Managed Object : Load all Mo( managed object ) cab : (cabinet ) cabx : (including boards) lt plug : ( load MO's) lst plug : ( Monitor per site including board ) str : ( status of RNC Locked and unlocked cell ) strt : status RNC with ETM Bords( ES-?-?-? ima 23 ) alt : (alarm to minitor sites ) alk : acknowledge( Warning/major or minor alarms) lgd : alarm log with downtime llog : Check restarted data lgaes : alarm log all lgs :display the system log for the whole period stored in system log (can be several months) lgasmi 30 them and show them :display the last 30 days of the alarm and system logs, merge in reverse chronological order. lgaevs 5h :display the last 5 hours of the alarm/event/availability/system logs. lgac 30m output into a csv file. bl :display the last 30 minutes of the alarm log and print the : ( Locked cell ) deb : (unlocked cell) pmr : will show statistics tg (Site id ) get radiolink get rbslocalcell:the below. ueregprint sum registered. ) : Check Cell error code, cellbarred, actor info. : User &Traffic : cell id / If the site dont comes up after intergration check : To view total users ( i.e ueregprint sum $ 380 UEs .lt iub : on both nodes .lk IubLink=Iub_GRYxxx : in RNC .lk iub=<iub>/lst iub : in RBS AAL2 Addresses :.get aal2routingcase=<rbsroutingcase: in RNC .get aal2sp=1966101000200046 : in RBS VCI values :- . get aal2path xxxx . lst bxxx . get bxxxxca : Nbap number only : without Nbap comman ID : with Nbap command ID ( Then will see the IUB Name ) localCellId :. lst cell : in RBS . get cell=gnj357 localcell : in RNC =============================================================== ========== Transmission :lacc atmport=<port>,vpltp=<vp>,vpctp=1,vclXX eteloopback : VCL 32 / 33 for signalling get cell= local get utrancell=gryXXX local get sync acc 0 restrart : RNC : in RNC : synchonization : restart Node B acc 010600 restart : restart AIUB sector 1 acc 010900 restart : restart AIUB sector 2 acc 011200 restart : restart AIUB sector 3 lhsh 001200 ps port * (3206) : VSWR ( Choose the TMA port ) exp: lhsh 001200/port_1_dev_12 asc vswr : for available for 3206 cabinet only =============================================================== ====== lhsh 010600 ps port * (3202)choose AIUB : for available for 3202 cabinet only exp: lhsh 010600/port_0_dev_18 asc vswr : for available for 3202 cabinet lhsh 010900 ps port * : for available for 3202 cabinet exp: lhsh 010900/port_0_dev_20 asc vswr : for available for 3202 cabinet lhsh 011200 ps port * exp: lhsh 011200/port_0_dev_22 asc vswr exp: : for available for 3202 cabinet =============================================================== ======= At NodeB : 10:19 11/02/2007 : lt ret : Calibrate RET lst ret : List RET device pr retdevice : get RET proxy get ret electrical : See overall value set (proxy) electricalAntennaTilt XX : Change tilting value get jumper : For jumper Attenuation get feeder : For Feeder Attenuation get feeder Attenuation : For Feeder Attenuation ( All Sector ) actl 1401/1402/1403 ) : Action list =Proxy = 1403 ( Choice either one frm actc 1401/1402/1403 ) : Action call =Proxy = 1403 ( Choice either one frm actc 1403 forceCalibration : ( Choice either one frm 1401/1402/1403 ) get 0 : RBS Type cvls : CV's Data get XXX (sector proxy) : Cell id lget utrancell cid XXXX : To check cell id at RNC st plug dif : list MO's ( Managed Object ) : Compare two Mos =============================================================== ============================ Must Perform at RNC:lget utrancell=(Site Num) utrancellref : To find neighbouring cell 3G lget utrancell=(Site Num) gsmcellref : To find neighbouring cell 2G lpr utrancell=(Site Num) utranrelation : To find all relation Utrancell & GSM lt utranc lget utran primarysc lget (Site Name) primarys : To Load Utrancell Scrambling codes : To find power and scarmbling codes. : To find sector scrambling codes for site. lget utran primarysc (Scrambling code) : To find same scrambling which is using to another site. get Aal2sp : To check the Aal2ea which is connected to RNC. lget Aal2sp : With operating state (NODE-B) lget (exp-Aal2sp:966101000200046) connected under this Nbap in RNC. get aal2pathvcctp=bXXXX lst bxxx(Nbap) : To check the Aal2Ap=bXXX which site is : To get path port from RNC : To check operating state with proxy. get bxxxca(Proxy) : To check Nbap Enable or Disable in RNC and will know whether the site is correct or not.. get sector lat/lon : To get sector's langlitude/longlitude. pr iub : To get RBS ID and get proxy/ NodeBFunction=1,Iub=GRYXXX pr retdevice get <proxy> get config : Ret device : Operating State : Overall Configuration In ( Node B & RNC ) =============================================================== ======================================== CVMS : To create New CV via moshell ( NODE B ) cvrm (cv-name) : Remove CV name cvms (cvname) : Create CV name cvmk (cvName) cvset (cvname) : to create cv : To set the Set Startable cvls date. : All Cv's Including Basic and Upgrade package with created cvcu : CV detail and Running CV =============================================================== ======================================== st atmport : To check E1 state in Node B lst plug 0 : To check locked board in node Acc 000900 restart : To restart / reload board In all nodes Acc 001400 reload : To restart / reload board In all nodes pmxh utrancell downtime pmr -m 5 lt vcl VclTp pget vcl VclTp : Downtime counters will be displayed side by side : will show statistics for the last 5 hours : Lt vcl e.g pmReceivedAtmCells/pmTransmittedAtmCells of : error :-pmReceivedAtmCells/pmTransmittedAtmCells of get all ingressAtmPcr Attribute: ingressAtmPcr get all in.*P st all dis : View only one attribute of all AtmTrafficDescriptors: : to view filter output : View all disable Mo's =============================================================== ================================================= CHECK E-1 RNC lst xxx : (gryxxx site name ) get proxy e.g b1102ca : ( proxy for nbapcommon/dediccated ) lst b1102 : ( print all atm layer com -note the aal2 ) Lpget (ATM boards) : ( to check performance TX/RX Error) get xxx : (proxy ATM PORT) pr etm : to print AAL path file. lcc xxx : (proxy ) Lst (copy paste subrack) st xxx LPget xxx : ATM port performance Error. : (proxy) : (proxy to get performance error E1)
0
advertisement
Download
advertisement
Add this document to collection(s)
You can add this document to your study collection(s)
Sign in Available only to authorized usersAdd this document to saved
You can add this document to your saved list
Sign in Available only to authorized users