Uploaded by Mazen Hodali

API 660 2015

advertisement
Shell-and-Tube Heat Exchangers
API STANDARD 660
NINTH EDITION, MARCH 2015
Special Notes
API publications necessarily address problems of a general nature. With respect to particular circumstances, local,
state, and federal laws and regulations should be reviewed.
Neither API nor any of API’s employees, subcontractors, consultants, committees, or other assignees make any
warranty or representation, either express or implied, with respect to the accuracy, completeness, or usefulness of the
information contained herein, or assume any liability or responsibility for any use, or the results of such use, of any
information or process disclosed in this publication. Neither API nor any of API’s employees, subcontractors,
consultants, or other assignees represent that use of this publication would not infringe upon privately owned rights.
API publications may be used by anyone desiring to do so. Every effort has been made by the Institute to assure the
accuracy and reliability of the data contained in them; however, the Institute makes no representation, warranty, or
guarantee in connection with this publication and hereby expressly disclaims any liability or responsibility for loss or
damage resulting from its use or for the violation of any authorities having jurisdiction with which this publication may
conflict.
API publications are published to facilitate the broad availability of proven, sound engineering and operating
practices. These publications are not intended to obviate the need for applying sound engineering judgment
regarding when and where these publications should be utilized. The formulation and publication of API publications
is not intended in any way to inhibit anyone from using any other practices.
Any manufacturer marking equipment or materials in conformance with the marking requirements of an API standard
is solely responsible for complying with all the applicable requirements of that standard. API does not represent,
warrant, or guarantee that such products do in fact conform to the applicable API standard.
Users of this Standard should not rely exclusively on the information contained in this document. Sound business,
scientific, engineering, and safety judgment should be used in employing the information contained herein.
All rights reserved. No part of this work may be reproduced, translated, stored in a retrieval system, or transmitted by any means,
electronic, mechanical, photocopying, recording, or otherwise, without prior written permission from the publisher. Contact the
Publisher, API Publishing Services, 1220 L Street, NW, Washington, DC 20005.
Copyright © 2015 American Petroleum Institute
Foreword
Nothing contained in any API publication is to be construed as granting any right, by implication or otherwise, for the
manufacture, sale, or use of any method, apparatus, or product covered by letters patent. Neither should anything
contained in the publication be construed as insuring anyone against liability for infringement of letters patent.
Shall: As used in a standard, “shall” denotes a minimum requirement in order to conform to the specification.
Should: As used in a standard, “should” denotes a recommendation or that which is advised but not required in order
to conform to the specification.
This document was produced under API standardization procedures that ensure appropriate notification and
participation in the developmental process and is designated as an API standard. Questions concerning the
interpretation of the content of this publication or comments and questions concerning the procedures under which
this publication was developed should be directed in writing to the Director of Standards, American Petroleum
Institute, 1220 L Street, NW, Washington, DC 20005. Requests for permission to reproduce or translate all or any part
of the material published herein should also be addressed to the director.
Generally, API standards are reviewed and revised, reaffirmed, or withdrawn at least every five years. A one-time
extension of up to two years may be added to this review cycle. Status of the publication can be ascertained from the
API Standards Department, telephone (202) 682-8000. A catalog of API publications and materials is published
annually by API, 1220 L Street, NW, Washington, DC 20005.
Suggested revisions are invited and should be submitted to the Standards Department, API, 1220 L Street, NW,
Washington, DC 20005, standards@api.org.
iii
Contents
Page
1
Scope . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
2
Normative References. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
3
Terms and Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
4
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
5
Proposal Information Required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
6
6.1
6.2
6.3
Drawings and Other Required Data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Outline Drawings and Other Supporting Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Information Required After Outline Drawings Are Reviewed. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Reports and Records . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7
7.1
7.2
7.3
7.4
7.5
7.6
7.7
7.8
7.9
7.10
7.11
7.12
Design . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Design Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Cladding for Corrosion Allowance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Shell Supports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Stationary and Floating Heads. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Tube Bundle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Nozzles and Other Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Flanged External Girth Joints . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Girth Flange Joint Supplementary Design Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Expansion Joints . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Gaskets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Handling Devices. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Requirements for Hydrogen Service. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
8
8.1
8.2
8.3
8.4
Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Requirements for Carbon Steel in Sour or Wet Hydrogen Sulfide Service . . . . . . . . . . . . . . . . . . . . . . . .
Gaskets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Tubes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
24
24
24
25
25
9
9.1
9.2
9.3
9.4
9.5
9.6
9.7
9.8
9.9
9.10
9.11
Fabrication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Shells . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Pass-partition Plates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Connection Junctions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Tubes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Welding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Heat Treatment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Dimensional Tolerances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Gasket Contact Surfaces Other Than Nozzle Flange Facings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Tube Holes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Tube-to-Tubesheet Joints . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
25
25
26
26
26
26
27
28
28
29
29
30
v
4
4
6
7
Contents
Page
10
10.1
10.2
10.3
Inspection and Testing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Quality Control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Pressure Testing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Nameplates and Stampings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
31
31
33
34
11 Preparation for Shipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
11.1 Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
11.2 Identification. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
12
12.1
12.2
12.3
Supplemental Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Design . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Examination . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
36
36
36
36
Annex A (informative) Recommended Practices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Annex B (informative) Shell-and-Tube Heat Exchanger Checklist. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Annex C (informative) Shell-and-Tube Heat Exchanger Datasheets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Bibliography . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Figures
1
Minimum Thickness of Tubes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2
Clearance Between Tube Holes and Transverse Baffle Edge with Longitudinal Baffle . . . . . . . . . . . . . .
3
Typical Cross-sections of Tube Bundle Showing Locations of Bypass Sealing Devices . . . . . . . . . . . .
4
Directions of Moments and Forces on Nozzles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10
12
14
16
Tables
1
Typical Designs for Floating-head Covers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2
Nozzle Allowable Forces and Moments at the Nozzle Neck to Shell/Channel Interface . . . . . . . . . . . . . .
3
Assembly Gasket Stress. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4
Gasket Contact Surface Finishes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5
Flatness Tolerance on Peripheral Gasket Contact Surfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6
Maximum Allowable Tube Wall Thickness Reduction for Roller-expanded Tube-to-Tubesheet Joints .
7
Hardness Limits. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
B.1 Checklist for Shell-and-Tube Heat Exchangers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10
16
20
28
29
30
32
46
vi
Introduction
It is necessary that users of this standard be aware that further or differing requirements can be needed for individual
applications. This standard is not intended to inhibit a vendor from offering, or the purchaser from accepting,
alternative equipment or engineering solutions for the individual application. This can be particularly applicable where
there is innovative or developing technology. Where an alternative is offered, the vendor should identify any variations
from this standard and provide details.
This standard requires the purchaser to specify certain details and features.
A bullet () at the beginning of a section indicates a requirement for the purchaser to make a decision or provide
information (for information, a checklist is provided in Annex B).
In this standard, where practical, U.S. Customary (USC) or other units are included in parentheses for information.
vii
Shell-and-Tube Heat Exchangers
1 Scope
This standard specifies requirements and gives recommendations for the mechanical design, material selection,
fabrication, inspection, testing, and preparation for shipment of shell-and-tube heat exchangers for the petroleum,
petrochemical, and natural gas industries.
This standard is applicable to the following types of shell-and-tube heat exchangers: heaters, condensers, coolers,
and reboilers.
This standard is not applicable to vacuum-operated steam surface condensers and feed-water heaters.
2 Normative References
The following referenced documents are indispensable for the application of this document. For dated references,
only the edition cited applies. For undated references, the latest edition of the referenced document (including any
amendments) applies.
ASME B16.5 1, Pipe Flanges and Flanged Fittings: NPS 1/2 through NPS 24 Metric/Inch Standard
ASME PCC-1-2013, Guidelines for Pressure Boundary Bolted Flange Joint Assembly
EJMA 2, Standards of the Expansion Joint Manufacturers Association
NACE MR0103 3, Materials Resistant to Sulfide Stress Cracking in Corrosive Petroleum Refining Environments
NACE MR0175, Petroleum and natural gas industries—Materials for use in H2S containing environments in oil and
gas production—Parts 1, 2 and 3
NACE SP0472, Methods and Controls to Prevent In-Service Environmental Cracking of Carbon Steel Weldments in
Corrosive Petroleum Refining Environments
TEMA 4, Ninth Edition, Standards of the Tubular Exchanger Manufacturers Association
3 Terms and Definitions
For the purposes of this document, the following definitions apply.
3.1
annular distributor
An additional chamber incorporated into a shell side nozzle to evenly distribute shell side fluids entering or exiting the
tube bundle.
1
2
3
ASME International, 2 Park Avenue, New York, New York 10016-5990, www.asme.org.
Expansion Joint Manufacturers Association, 25 North Broadway, Tarrytown, New York 10591, www.ejma.org.
NACE International (formerly the National Association of Corrosion Engineers), 1440 South Creek Drive, Houston, Texas
77084-4906, www.nace.org.
4 Tubular Exchanger Manufacturers Association, 25 North Broadway, Tarrytown, New York 10591, www.tema.org.
1
2
API STANDARD 660
3.2
category A welded joint
Longitudinal welded joint within the main shell, communicating chambers, nozzles, or transitions in diameter; or any
welded joint within a sphere or within a formed or flat head; or circumferential welded joint connecting hemispherical
heads to main shells, to transitions in diameters, or to communicating chambers.
3.3
category B welded joint
Circumferential welded joint within the main shell, communicating chambers, nozzles, or transitions in diameter
including joints between the transitions and a cylinder at either the large or small end; or circumferential welded joint
connecting formed heads, other than hemispherical to main shells, to transitions in diameter, to nozzles, or to
communicating chambers.
3.4
communicating chamber
Heat exchanger appurtenance that intersects the shell or heads of the heat exchanger and forms an integral part of
the pressure-containing envelope.
EXAMPLE
Sump, Annular Distributor.
3.5
cyclic service
Process operation with periodic variation in temperature, pressure, and/or flow rate.
3.6
effective heat transfer area
Outside surface area of the tubes that contributes to heat transfer including finned surface (if any).
3.7
full-penetration weld
Welded joint which results in weld metal through the entire thickness of the components being joined.
3.8
heat exchanger unit
One or more heat exchangers arranged in series or parallel for a specified service that operate together to perform
the intended duty.
3.9
hydrogen service
Services that contain hydrogen at a partial pressure exceeding 700 kPa (100 psi) absolute.
3.10
item number
Purchaser’s identification number for a heat exchanger unit.
3.11
minimum design metal temperature
MDMT
Lowest metal temperature at which pressure-containing elements can be subjected to design pressure.
EXAMPLE
Ambient temperature or process fluid temperature.
SHELL-AND-TUBE HEAT EXCHANGERS
3
3.12
nubbin
Projection on the flange gasket surface, positioned at the center of the gasket, used to concentrate the bolt load on
the gasket.
3.13
pressure design code
Recognized pressure vessel standard specified or agreed by the purchaser.
EXAMPLE
ASME BPVC, Section VIII, EN 13445 (all parts).
3.14
seal-welded
Tube-to-tubesheet joint weld of unspecified strength applied between the tubes and tubesheets for the sole purpose
of reducing the potential for leakage.
3.15
strength-welded
Tube-to-tubesheet joint welded so that the design strength is equal to, or greater than, the axial tube strength
specified by the pressure design code.
4 General
● 4.1 The pressure design code shall be specified or agreed by the purchaser. Pressure components shall comply
with the pressure design code and the supplemental requirements given in this standard.
4.2 Heat exchanger construction shall conform to TEMA, Class R, unless another TEMA class is specified.
● 4.3 The vendor shall comply with the applicable local regulations specified by the purchaser.
4.4 Annex A includes some recommended mechanical and design details for information.
4.5 Annex B provides a checklist that can be used by the purchaser to ensure that bulleted items in this standard
are addressed.
4.6 Annex C provides examples of data sheets.
● 4.7 The purchaser shall specify if either stream has fluid characteristics requiring special considerations (e.g. slurry,
entrained particulates, or other certain types of fouling mechanisms).
● 4.8 The purchaser shall specify if cyclic service design is required.
4.9 If cyclic service is specified, the purchaser shall specify the type and magnitude of variation in pressure,
temperature and flow rate, the time for the variation (hours, weeks, months, etc.) and the number of cycles or
frequency for this variation expected during the life of the equipment. The extent and acceptance criteria of any
required analysis shall be subject to the agreement of the purchaser. See A.2.1 for guidance on cyclic service.
● 4.10 The purchaser shall specify if the service is designated as sour in accordance with NACE MR0175 (all parts)
for oil and gas production facilities and natural gas processing plants or is designated as wet hydrogen sulfide service
in accordance with NACE MR0103 for other applications (e.g. petroleum refineries, LNG plants, and chemical plants),
in which case all materials in contact with the process fluid shall meet the requirements of the applicable standard to
mitigate potential for sulfide stress cracking (SSC). Identification of the complete set of materials, qualification,
fabrication, and testing specifications to prevent in-service environmental cracking is the responsibility of the user
(purchaser). See A.2.2 for guidance on sour or wet hydrogen sulfide service.
4
API STANDARD 660
● 4.11 The purchaser shall specify if the shell or tube side is in hydrogen service.
● 4.12 For single tube pass floating-head and all fixed tubesheet heat exchangers, the purchaser shall specify the
data required to determine the need for an expansion joint. This shall include all intended operating conditions defined
on the expansion joint datasheet shown in Annex C.
5 Proposal Information Required
5.1 For each heat exchanger unit, the vendor’s proposal shall include completed datasheets, such as those given in
Annex C, or if a datasheet is included in the inquiry, a statement indicating complete compliance with that datasheet.
5.2 The vendor’s proposal shall include sketches that are sufficient to describe the construction for the following, if
provided:
a) design features that are not fully defined by the nomenclature in TEMA, Section 1;
b) an annular distributor;
c) floating-head designs which include a tail-pipe and expansion joint;
d) expansion joints for fixed tubesheet exchangers. Including the location, material and type;
e) high pressure closure including channel to tubesheet attachment, shell to tubesheet attachment, and welded
diaphragm or welded lip-seal construction.
5.3 The proposal shall include a detailed description of all exceptions to the requirements of the purchaser’s inquiry.
5.4 For stacked heat exchangers, the vendor shall supply the following components, unless otherwise specified by
the purchaser:
a) bolts, nuts, and gaskets for interconnecting nozzles;
b) shims or spacers and bolting for interconnecting supports.
5.5 The vendor shall provide a separate quotation for the following items, unless otherwise specified by the
purchaser.
a) A test component consisting of a test ring and gland, in accordance with TEMA, Figure E-4.13-2 or equivalent, for
each heat exchanger or group of similar heat exchangers with floating heads.
b) One spare gasket for each external girth flange, floating-head flange (if applicable), and internal pass-partition
flange (if applicable) per heat exchanger.
6 Drawings and Other Required Data
6.1 Outline Drawings and Other Supporting Data
6.1.1 The vendor shall submit, for review by the purchaser, outline drawings for each heat exchanger unit. The
drawings shall include at least the following information:
a) service, item number, project name and location, purchaser’s order number, vendor’s shop order number, and
other special identification numbers;
SHELL-AND-TUBE HEAT EXCHANGERS
5
b) design pressure, test pressure, design temperature, minimum design metal temperature, and any restriction on
testing or operation of the heat exchanger;
c) maximum allowable working pressure (MAWP) in the corroded condition and at the design temperature for the
shell side and tube side;
d) connection sizes, location, orientation, projection, direction of flow and, if flanged, the rating and facing or, if
welded to the connecting piping, the weld bevel preparation;
e) coupling sizes, rating, and orientation;
f) dimensions, orientation and location of supports, including bolt holes and slots, and the stacking arrangement;
g) overall dimensions of the heat exchanger;
h) tube bundle removal clearance;
i) mass of the heat exchanger, empty and full of water, and of removable components with a mass greater than
25 kg (60 lb), (e.g. removable tube bundle, channel, channel cover, and shell cover);
j) specified corrosion allowance for each side of the heat exchanger (see A.3.1);
k) references to the applicable code and the purchaser’s specification;
l) requirements for postweld heat treatment;
m) requirements for non-destructive examination (NDE);
n) requirements for material impact testing;
o) requirements for surface preparation and painting;
p) gasket materials;
q) insulation thickness;
r) location of expansion joints, annular distributors, and any other special components or closures;
s) location and orientation of nameplates, lifting lugs, grounding clips or other attachments;
t) location of the center of gravity of the heat exchanger (empty and full of water);
u) forces and moments on connections as specified by the purchaser (see 7.6.9);
v) material specifications and grades for all components.
● 6.1.2 The vendor shall submit flow-induced vibration analysis, if specified by the purchaser. See A.3.2.
6.1.3 The vendor shall recommend the tools required for the assembly and maintenance of the heat exchanger. If
torquing or tensioning of bolts is required, the vendor shall provide applicable procedures.
6.1.4 The review of engineering documents by the purchaser shall not relieve the vendor of the responsibility of
meeting the requirements of the purchase order.
6
API STANDARD 660
6.2 Information Required After Outline Drawings Are Reviewed
6.2.1 The vendor shall submit gasket details, including type and material, on a separate drawing. This drawing shall
not be marked with any restrictions for use.
● 6.2.2 If specified by the purchaser, the vendor shall furnish copies of applicable welding procedure specifications
and welding procedure qualifications for review or record.
6.2.3 Upon receipt of the purchaser’s review comments on the outline drawings, the vendor shall submit copies of
all detailed drawings for the purchaser’s review. These shall fully describe the heat exchanger and shall include at
least the following information:
a) full views and cross-sectional views with all dimensions and materials sufficient for stress calculations for each
part;
b) tube bundle details, including the following:
— tube layout,
— tube description and number in each pass,
— number of baffles, type and description (for segmental baffles include cross-baffle cut, layout, and orientation
in a view that shows the cuts),
— details and locations of all sealing and sliding strips,
— details and locations of tie-rods and spacers,
— details and locations of support plates,
— details of tubesheet and tube holes, including cladding or weld overlay if required,
— details of pass-partition plates,
— impingement protection device details, if applicable,
— U-tube bend schedule, if applicable;
c) details of each pressure-retaining weld, including weld material, weld nominal thickness, weld location, and
applicable non-destructive examination method;
d) details of each weld and weld nominal thickness for nonpressure attachments welded to pressure parts and for all
load bearing attachments;
e) complete bills of materials, including the material specification;
f) expansion joint details;
g) details of cladding and weld overlay;
h) weld map for each heat exchanger showing the weld joints, including welding procedure number(s);
i) details of tube-to-tubesheet joints, including procedures for installation, welding, expansion, inspection, and
testing;
SHELL-AND-TUBE HEAT EXCHANGERS
7
j) flange-face finish;
k) special installation and maintenance instructions including lifting and handling.
6.2.4 The vendor shall submit for the purchaser’s review the following documentation.
a) Mechanical design calculations for all the heat exchanger pressure-retaining components. If calculations are
made using computer software, all input and output data shall be detailed so as to facilitate an understanding of
the calculation procedures. The formulas in the applicable sections of the pressure design code and TEMA shall
be referenced.
b) Design calculations based on seismic, wind, transportation, and piping loads, if these loads are provided by the
purchaser.
c) Proposed procedures for assembly of flanged joints, if controlled bolt-tightening procedures (such as hydraulic
torque wrenches or hydraulic tensioning devices) are used. Any required lubricants shall be stated.
d) Design calculations for thermal loads imposed on nozzles of stacked heat exchangers, when the shell mean metal
temperature differential between the stacked shells exceeds 110 °C (200 °F) for ferritic steels and 75 °C (135 °F)
for non-ferritic steels.
e) Design calculations for expansion joints, if applicable.
● 6.2.5 The vendor shall submit design calculations for supports, lifting, and pulling devices, if specified by the
purchaser.
6.2.6 After final review the vendor shall revise all the required drawings and welding procedures, and submit each
with the following text marked on every sheet separately and dated: “CERTIFIED FOR CONSTRUCTION.”
6.3 Reports and Records
● After the heat exchanger is completed the vendor shall furnish the purchaser with the following documents in the
format and quantities specified by the purchaser:
a) “as-built” datasheet;
b) all outline and detail drawings, marked “CERTIFIED AS-BUILT”;
c) certified record of all impact tests performed;
d) certified mill test reports for all pressure parts, including tubes (each material test report shall be identified by a
part number);
e) complete certified bill of materials suitable for obtaining all replacement parts, including quantity, description,
material specification, and identification of each part;
f) temperature charts of all postweld heat treatments;
g) completed manufacturer’s data report in accordance with the pressure design code;
h) nameplate rubbing or a facsimile;
i) all mechanical design calculations, marked “CERTIFIED AS-BUILT”;
8
API STANDARD 660
j) non-destructive examination (NDE) map;
k) all associated NDE reports, including radiographic, magnetic-particle, liquid-penetrant, ultrasonic, hardness,
impact, positive material identification (PMI), and any other reports as applicable;
l) tube-to-tubesheet leak-test results;
m) hydrostatic test records in the form of a chart or certification;
n) tube wall reduction records.
7 Design
7.1 Design Temperature
● 7.1.1 All heat exchangers shall have two design temperatures for each side, a maximum design temperature and a
minimum design metal temperature (MDMT), as specified by the purchaser.
7.1.2 The design temperature of a component (including external bolting) influenced by both the shell side and tube
side fluids shall be the more severe of either the shell side or tube side design temperature.
7.2 Cladding for Corrosion Allowance
7.2.1 If cladding (including weld overlay) is used, the cladding thickness including weld overlay restoration shall be
used only as corrosion allowance and not as the pressure retaining envelope, unless otherwise specified or approved
by the purchaser.
7.2.2 Weld overlays (including weld overlay restoration) shall have sufficient thickness to provide the specified
chemical composition to a depth of at least 1.5 mm (1/16 in.) from the finished surface, unless otherwise specified by
the purchaser. Pass partition grooves of tubesheets and gasket contact surfaces shall also comply with this
requirement after final machining.
7.2.3 The cladding (including weld overlay) thickness at the tube side face of a tubesheet shall not be less than
10 mm (3/8 in.) when tubes are expanded only, and 5 mm (3/16 in.) when tubes are welded to the tubesheet.
7.2.4 The cladding or weld overlay thickness on the shell side face of a tubesheet shall not be less than 10 mm
(3/8 in.).
7.2.5 Where seal-welded diaphragm or lip-seal gaskets are used, the weld overlay shall have a minimum thickness
of 6 mm (1/4 in.) applied to the gasket seating surface.
7.3 Shell Supports
7.3.1 When the support of a removable-bundle heat exchanger is fixed to the shell, it shall be designed to withstand
a longitudinal force equal to 150 % of the bundle mass applied at the heat exchanger bundle centerline. The shear
stress for supports shall not exceed 40 % of the yield strength of the material.
7.3.2 Horizontal heat exchangers shall be provided with two or more saddles designed to support the heat
exchanger under all specified conditions. Design of the saddles shall be as follows:
a) saddles shall be attached to saddle bearing-plates;
b) the bearing surface of the saddles shall be at least one-third of the circumference of the shell;
SHELL-AND-TUBE HEAT EXCHANGERS
9
c) saddle-bearing plates shall have the same nominal chemical composition as the shell and shall be continuously
welded directly to the heat exchanger shells;
d) saddle-bearing plates shall be provided with vent holes 6 mm (1/4 in.) in diameter, located at the vertical
centerline;
e) saddle-bearing plates shall be at least 6 mm (1/4 in.) thick and shall have all corners rounded to a radius of at least
25 mm (1 in.).
7.3.3 The lower shells of stacked removable-bundle heat exchangers shall be designed to carry the superimposed
loads without suffering distortion that could cause binding of the tube bundles.
7.3.4 The vendor’s design shall provide for a shim allowance of approximately 6 mm (1/4 in.) between the faces of
stacked heat exchanger intermediate supports.
7.3.5 For horizontal heat exchangers, slotted holes shall be provided in the baseplate of all but one of the saddles to
allow for longitudinal movement due to thermal expansion or contraction. The width of the slot shall be equal to the
anchor bolt diameter plus 8 mm (5/16 in.). The length of the slot shall be equal to the anchor bolt diameter, plus the
allowance for longitudinal movement, plus 8 mm (5/16 in.).
● 7.3.6 For all supports the local stresses in the shell shall be analyzed using a method which is specified or agreed
with the purchaser.
EXAMPLE
WRC BUL 537.
7.3.7 A grounding lug shall be attached to at least one of the exchanger supports.
7.4 Stationary and Floating Heads
7.4.1 Stiffeners shall not be used for channel cover design as a means of retaining pressure or to prevent deflection.
7.4.2 The pressure differential used to calculate the pass-partition plate thickness in accordance with TEMA,
Section 5, Paragraph RCB-9.132 shall be at least twice the calculated pressure drop across each pass-partition plate.
The plate thickness shall not be less than two times the tube side corrosion allowance, plus 3 mm (1/8 in.).
7.4.3 Floating-head cover bolting shall comply with TEMA, Section 5, Paragraph RCB-11. Bolt spacing and
clearances shall not be less than the minimum recommended by TEMA.
7.4.4 Floating-head cover bolting shall be readily accessible and shall have adequate spanner (wrench) clearance
between the floating-head bolts and the shell flange at the cover end when the shell cover is removed.
7.4.5 Packed floating-head tailpipe and packed floating tubesheet designs (e.g. TEMA types P and W) shall not be
used.
7.4.6 Unless otherwise specified by the purchaser, floating-heads shall be designed for design pressure on either
side, with atmospheric pressure or, if specified, vacuum on the other side. Examples of acceptable floating-head
designs are shown in Figure 1.
7.4.7 Internal floating-head covers shall have the specified corrosion allowance on all wetted surfaces, except
gasket seating surfaces. The specified corrosion allowance shall be included on the back side of the floating-head
backing device.
7.4.8 Nubbins shall not be used on floating-head flanges.
10
API STANDARD 660
Dish
Ring
Dish
Flange
Full-penetration weld
Integral
machined
cover
Full-penetration weld
Gasket
Gasket
a) Ring and Dish
Construction
Gasket
b) Flange and Dish
Construction
c) Integral
Construction
Figure 1—Typical Designs for Floating-head Covers
7.4.9 The shell cover on horizontal S-type floating-head exchangers shall be equipped with a vent and drain.
7.4.10 S-type floating-heads shall utilize style A (dove-tail) split rings per TEMA, Figure RCB-5.141. The dove-tail
mating surfaces shall have rounded corners.
● 7.4.11 When specified by the purchaser, all girth flanges, channel covers, and floating-head flanges shall be
provided with 3 mm (1/8 in.) future machining allowance on the gasket contact seating surfaces (including passpartition surfaces). The additional thickness shall not be used in the calculation of maximum allowable working
pressure.
NOTE
This requirement does not apply to clad or weld overlay construction.
7.5 Tube Bundle
7.5.1 Tubes
7.5.1.1 The minimum outside diameter of the tubes shall be 19.05 mm (3/4 in.), unless otherwise specified or
approved by the purchaser. See A.4.1 for additional guidance on selection of tube diameter.
7.5.1.2 The tube wall thickness shall be as listed in Table 1, or thicker if required by the design conditions, including
any tube corrosion allowance specified by the purchaser.
Table 1—Minimum Thickness of Tubes
Dimensions in millimeters (inches)
Tube Material
Minimum Thicknessa
Carbon steel, low-alloy steel (max. 9 % chromium), aluminum, and
aluminum alloy
2.11 (0.083)
Copper and copper alloys
1.47 (0.058)
High-alloy [austenitic, ferritic, and austenitic/ferritic (duplex)] steel and
other nonferrous materials
1.47 (0.058)
Titanium
1.07 (0.042)
a
Tubes shall be furnished on either a minimum wall basis or an average wall basis, provided the tube thickness is not less
than that specified above.
SHELL-AND-TUBE HEAT EXCHANGERS
11
7.5.1.3 For carbon and low alloy steel low-fin tubing, the wall thickness under the root of the fin shall be in
accordance with Table 1.
7.5.1.4 The mean radius of U-bends shall not be less than 1.5 times the nominal outside diameter of the tube. For
martensitic stainless steels, super austenitic stainless steels (>6 wt % Mo) duplex stainless steels, titanium, and high
nickel alloys (>30 wt % Ni), the mean radius of U-bends shall not be less than 2.0 times the nominal outside diameter
of the tube.
7.5.1.5 For U-tubes, design calculations shall be based on the reduction in wall thickness associated with bending.
The thickness of the tubes need not be increased to meet the requirements in Table 1 provided the wall thickness in
the U-bends meet the minimum requirements of the pressure design code and any specified tube corrosion
allowance.
7.5.1.6 For U-tube and floating head type exchangers, the minimum clearance between any part of the U-bend or
floating head cover, and the shell rear head, shall be 38 mm (11/2 in.), to accommodate thermal expansion of the tube
bundle. Both the crown and knuckle of the head shall be considered.
7.5.1.7 The number of tubes in any pass shall not be greater than 10 % above or below the average number of
tubes per pass, unless otherwise approved by the purchaser.
7.5.2 Tubesheets
7.5.2.1 For a vertical heat exchanger where the stationary tubesheet is at the bottom, a suitable means of holding
the tube bundle in place shall be provided for when the bonnet or channel is removed. If collar bolts or drilled-andtapped holes are used, at least four shall be provided and their location shall be identified on the drawings and by
stamped markings on the OD of the tubesheet.
7.5.2.2 The distance between the edge of the tube holes and the edge of all gasket grooves (including pass-partition
grooves) shall not be less than 1.5 mm (1/16 in.) for tubesheets with expanded tube-to-tubesheet joints and not less
than 3 mm (1/8 in.) for tubesheets with welded tube-to-tubesheet joints.
7.5.2.3 Unless otherwise specified or approved by the purchaser, tubesheets shall be designed for design pressure
on either side, with atmospheric pressure or, if specified, vacuum on the other side.
7.5.2.4 A full diameter stationary tubesheet shall be provided for removable tube bundle exchangers with bonnets
(see TEMA, Figure N-1.2, Type B stationary head). The tubesheet shall be provided with collar studs or tapped
tubesheet holes for a minimum of 25 % of the bolts (4 minimum). The tubesheet design shall allow for hydrostatic
testing of the shell side with the bonnet removed and all bolting installed.
● 7.5.2.5 When specified by the purchaser, tubesheets shall be provided with 3 mm (1/8 in.) future machining
allowance on the gasket contact seating surface (including pass-partition surfaces). The purchaser shall state if this
3 mm (1/8 in.) allowance shall be provided on one or both of the shell side and tube side surfaces of the tubesheet.
The additional thickness shall not be used in the calculation of maximum allowable working pressure.
NOTE
This requirement does not apply to clad or weld overlay construction.
7.5.2.6 For vertical fixed tubesheet exchangers, a means shall be provided to completely vent and drain the shell.
7.5.3 Baffles and Support Plates
7.5.3.1 The thickness of carbon steel or low-alloy steel (maximum 9 % chromium) transverse baffles and support
plates shall not be less than twice the specified shell side corrosion allowance. See A.4.2 for additional guidance.
12
API STANDARD 660
7.5.3.2 To facilitate drainage of the shell, transverse baffles and support plates shall have notches that are 6 mm
(1/4 in.) in height for shell diameters up to and including 406 mm (16 in.), and 10 mm (3/8 in.) in height for larger shell
diameters.
7.5.3.3 If shell side longitudinal baffles are used, the minimum clearance (ligament) between the transverse baffle
edge and the tube holes in the baffles shall be 3 mm (1/8 in.) as shown in Figure 2.
Transverse baffle
Tube hole
3 mm (1/8 in.) clearance
(ligament) between the
baffle tube holes and the
transverse baffle edge
Longitudinal baffle
Transverse baffle
Figure 2—Clearance Between Tube Holes and Transverse Baffle Edge with Longitudinal Baffle
7.5.4 Impingement Protection
7.5.4.1 If required by TEMA, Section 5, Paragraph RCB-4.61, impingement protection shall be provided by a plate
baffle or rods on the tube bundle, an annular distributor, or another means agreed by the purchaser and vendor.
7.5.4.2 If an impingement plate baffle is used, it shall extend at least 25 mm (1 in.) beyond the projection of the
nozzle bore (e.g. for a round impingement plate, the plate diameter shall be at least 50 mm (2 in.) larger than the
nozzle bore) or 20 % greater than the inlet nozzle inside diameter, whichever is larger.
7.5.4.3 If impingement protection is used, the shell entrance and tube bundle entrance areas (as defined by TEMA,
Section 5, Paragraph RCB 4.62) shall not be less than the flow area of the inlet nozzle.
7.5.4.4 The nominal thickness of impingement plate baffles shall not be less than 6 mm (1/4 in.).
7.5.4.5 The impingement plate baffle shall be adequately supported (e.g. by welding to at least two spacers) to
avoid mechanical damage due to vibration.
7.5.4.6 Perforated impingement plate baffles shall not be used.
SHELL-AND-TUBE HEAT EXCHANGERS
13
7.5.4.7 If impingement rods are utilized, the following shall be applied.
a) A minimum of two rows of staggered rods shall be used.
b) The rods shall not have a diameter less than 19 mm (3/4 in.).
c) Tube center-to-center spacing shall be 1.25 to 1.33 times the rod diameter.
d) The length and width of the rod array shall extend at least 50 mm (2 in.) beyond the projection of the nozzle bore
or 20 % greater than the inlet nozzle inside diameter, whichever is larger.
e) For carbon, low alloy, and austenitic stainless steel materials the rods shall be supplied as solid bars; for other
materials tubing can be used if approved by the purchaser.
f) Impingement rods shall be supported at both ends. When attached to the tubesheet, impingement rods shall not
be attached by welding alone.
7.5.5 Bypass Sealing Devices
7.5.5.1 Bypass sealing devices (such as seal bars, dummy tubes or tie-rods) as shown in Figure 3 shall be used for
non-isothermal shell side services if bypass clearances exceed 16 mm (5/8 in.) and shall be located as follows.
a) If the distance between baffle-cut edges is six tube pitches or less, a single seal located approximately halfway
between the baffle cut shall be provided.
b) If the distance between baffle-cut edges exceeds six tube pitches, multiple seals shall be provided. A seal shall be
located every five to seven tube pitches between the baffle cuts, with the outermost seals not more than 75 mm
(3 in.) from each baffle-cut edge.
7.5.5.2 Peripheral bypass seals shall extend from the peripheral edge of the transverse baffle into the tube bundle
so that the clearance to the nearest tube does not exceed the nominal clearance between tubes.
7.5.5.3 Internal bypass seals shall be installed so that the clearance to the nearest tube does not exceed the
nominal clearance between tubes.
7.5.5.4 Bypass sealing devices shall either be located to minimize obstruction of mechanical cleaning lanes or shall
be readily removable. Continuous cleaning lanes shall be maintained for square (90°) and rotated-square (45°) pitch.
7.5.5.5 The nominal thickness of seal strips shall be the nominal thickness of the transverse baffles or 6 mm (1/4 in.),
whichever is less.
7.5.5.6 Bypass seal strips shall be attached to the transverse baffles by continuous welds on one side of each
baffle.
7.5.5.7 The leading and trailing edges of seal strips shall be provided with a radius or a bevel to prevent damage to
the shell when inserting or removing the tube bundle.
7.5.5.8 Peripheral bypass seal strips shall not restrict the tube bundle inlet or outlet flows.
7.5.6 Tube Bundle Skid Bars
7.5.6.1 For all removable tube bundles with a mass of more than 5500 kg (12,000 lb), continuous sliding surfaces
shall be provided to facilitate bundle removal. If skid bars are used, they shall be welded to the transverse baffles and
support plates to form a continuous sliding surface. See A.4.3 for additional guidance.
14
API STANDARD 660
1
2
14
3
4
13
12
6
11
5
8
7
15
16
10
9
Key
1
2
3
4
5
6
7
8
peripheral edge of baffle
tie-rods, dummy tubes, or flat bar
edge of baffle cut
plane of U-tube bend
detail of seals and tube clearance
tubes
seal
clearance: not to exceed nominal clearance between tubes
9
10
11
12
13
14
15
16
single seal on centerline
multiple seals, evenly spaced
edge of baffle cut
plane of U-tube bend
U-tube bend
impingement plate
peripheral bundle bypass lane
internal bundle bypass lane
Figure 3—Typical Cross-sections of Tube Bundle Showing Locations of Bypass Sealing Devices
7.5.6.2 If skid bars are used, a minimum of two shall be provided.
7.5.6.3 Skid bars shall not restrict the tube bundle inlet or outlet flows.
7.5.6.4 Skid bars shall protrude 1 mm (1/32 in.) beyond the outside diameter of baffle and support plates.
7.5.6.5 The leading and trailing edges of skid bars shall be provided with a radius or a bevel to prevent damage to
the shell when inserting or removing the tube bundle.
SHELL-AND-TUBE HEAT EXCHANGERS
15
7.5.7 Tube-to-Tubesheet Joint
7.5.7.1 Tube-to-tubesheet joints shall be expanded with a minimum of two grooves, unless a strength-welded tubeto-tubesheet joint is specified by the purchaser on the datasheet.
7.5.7.2 If welded tube-to-tubesheet joints are specified, the joint shall be welded by one of the following methods:
a) strength-welded only;
b) strength-welded and expanded;
c) seal-welded and expanded.
● 7.5.7.3 When strength welds are applied, the degree of expansion and the use of grooves shall be specified or
agreed to by the purchaser. See Annex A.4.4 for additional guidance on the selection of tube-to-tubesheet joints.
7.6 Nozzles and Other Connections
● 7.6.1 Connections DN 40 (NPS 11/2) and larger shall be flanged. The purchaser shall specify the required flange
design code (e.g. ASME B16.5).
● 7.6.2 The purchaser shall specify if nozzles are to be welded to the connecting piping (by others). They shall be
beveled and details shall be specified or agreed with the purchaser.
7.6.3 Non-flanged connections smaller than DN 40 (NPS 11/2) shall be forged couplings with a rating that meets or
is equivalent to ASME B16.11 class 6000, or shall be integrally reinforced welding fittings with tapered threads that
meet or are equivalent to ASME B1.20.1, and shall comply with the pressure design code. Threaded connections
shall not be used in hydrogen, sour, or wet hydrogen sulfide service. This includes auxiliary connections, such as
vents, drains, instrument connections, and chemical cleaning connections.
7.6.4 Flanged connections shall be of one of the following types:
a) forged integrally flanged;
b) pipe or forged cylinder welded to forged welding-neck flange;
c) pipe welded to a forged slip-on flange, except as noted in 7.6.5.
7.6.5 Slip-on flanges shall not be used in any of the following conditions:
a) design pressure greater than 2100 kPa (ga) (300 psig);
b) design temperature greater than 400 °C (750 °F);
c) corrosion allowance greater than 3 mm (1/8 in.);
d) hydrogen, sour, or wet hydrogen sulfide service;
e) cyclic service.
● 7.6.6 The projection of flanged connections shall allow through-bolting to be removed from either side of the flange
without removing the insulation. For stacked units, this requirement need only be applied to one side of directly
coupled connections. The insulation thickness shall be specified by the purchaser.
16
API STANDARD 660
7.6.7 Integrally reinforced nozzles shall be designed so that standard spanners (wrenches) fit the nuts without
interference from nozzle neck reinforcement.
● 7.6.8 The purchaser shall specify if chemical cleaning connections are required. Their nominal size shall be not less
than DN 50 (NPS 2).
● 7.6.9 Nozzles shall be designed to withstand the simultaneous application of forces and moments in the corroded
condition, as defined in Figure 4 and listed in Table 2, unless otherwise specified by the purchaser. Non-piped
auxiliary connections, such as vents, drains, and cleaning connections, are excluded from this requirement. The type
of analysis applied shall be specified or agreed with the purchaser.
● 7.6.10 For nozzle sizes larger than those listed in Table 2, the purchaser shall specify the moments and forces.
+Y
Y
+M Y
+MZ
X
+M X
+Z
+X
Figure 4—Directions of Moments and Forces on Nozzles
Table 2—Nozzle Allowable Forces and Moments at the Nozzle Neck to Shell/Channel Interface
Nominal
Diameter
DN (NPS)
50
80
2
3
Flange
Rating
Mx
My
Mz
Fx
Fy
Fz
N·m
(lbf·ft)
N·m
(lbf·ft)
N·m
(lbf·ft)
N
(lbf)
N
(lbf)
N
(lbf)
150
270
200
430
320
340
250
1590
370
1270
290
1590
370
300
340
250
540
400
430
320
1990
450
1590
360
1990
450
600
470
350
750
560
590
440
2780
630
2220
500
2780
630
900
600
440
970
720
760
560
3580
820
2860
650
3580
820
1500
600
440
970
720
760
560
3580
820
2860
650
3580
820
2500
670
490
1080
790
850
630
3970
900
3170
720
3970
900
150
580
430
940
690
740
540
2340
530
1870
420
2340
530
300
720
540
1170
860
920
680
2930
670
2340
530
2930
670
600
1010
750
1630
1210
1280
950
4090
930
3270
740
4090
930
900
1300
960
2100
1550
1650
1220
5270
1190
4210
950
5270
1190
1500
1300
960
2100
1550
1650
1220
5270
1190
4210
950
5270
1190
2500
1590
1170
2560
1890
2010
1490
6430
1450
5140
1160
6430
1450
SHELL-AND-TUBE HEAT EXCHANGERS
17
Table 2—Nozzle Allowable Forces and Moments at the Nozzle Neck to Shell/Channel Interface (Continued)
Nominal
Diameter
DN (NPS)
100
150
200
250
300
4
6
8
10
12
Flange
Rating
Mx
My
Mz
Fx
Fy
Fz
N·m
(lbf·ft)
N·m
(lbf·ft)
N·m
(lbf·ft)
N
(lbf)
N
(lbf)
N
(lbf)
150
960
710
1540
1140
1210
900
3020
680
2410
540
3020
680
300
1190
880
1930
1420
1520
1120
3770
850
3010
680
3770
850
600
1670
1230
2700
1990
2120
1560
5270
1190
4210
950
5270
1190
900
2150
1580
3460
2560
2720
2010
6770
1530
5410
1220
6770
1530
1500
2380
1760
3850
2840
3030
2230
7520
1690
6010
1350
7520
1690
2500
2620
1930
4230
3120
3330
2460
8270
1870
6610
1490
8270
1870
150
2070
1530
3340
2460
2620
1940
4430
1000
3540
800
4430
1000
300
3610
2670
5840
4310
4590
3380
7740
1750
6190
1400
7740
1750
600
4640
3430
7500
5540
5900
4350
9950
2240
7960
1790
9950
2240
900
5670
4190
9170
6760
7210
5320
12170
2740
9730
2190
12170
2740
1500
6710
4950
10840
7990
8520
6280
14380
3240
11500
2590
14380
3240
2500
7220
5330
11670
8610
9170
6760
15480
3490
12380 2790
15480
3490
150
3500
2580
5650
4170
4440
3280
5770
1300
4610
1040
5770
1300
300
6120
4510
9890
7300
7770
5730
10080
2280
8060
1820
10080
2280
600
8740
6450
14130
10420
11100
8190
14390
3240
11510
2590
14390
3240
900
12230
9020
19780
14590
15540
11460
20150
4540
16120 3630
20150
4540
1500
13980
10310
22600
16670
17760
13100
23030
5180
18420 4140
23030
5180
2500
14860
10960
24010
17710
18870
13920
24470
5500
19570 4400
24470
5500
150
5430
4010
8780
6480
6900
5090
7180
1620
5740
1290
7180
1620
300
9500
7010
15360
11330
12070
8900
12570
2830
10050 2260
12570
2830
600
13580
10010
21940
16180
17240
12720
17940
4040
14350 3230
17940
4040
900
19000
14020
30720
22660
24140
17800
25120
5650
20090 4520
25120
5650
1500
21720
16020
35110
25890
27580
20340
28700
6450
22960 5160
28700
6450
2500
23070
17020
37300
27510
29310
21620
30490
6870
24390 5490
30490
6870
150
7640
5640
12350
9110
9700
7160
8520
1920
6810
1530
8520
1920
300
13370
9860
21610
15940
16980
12520
14890
3350
11910
2680
14890
3350
600
15280
11270
24690
18210
19400
14310
17030
3830
13620 3060
17030
3830
900
17190
12680
27780
20490
21830
16100
19150
4320
15320 3450
19150
4320
1500
21000
15490
33950
25040
26680
19680
23400
5270
18720 4210
23400
5270
2500
22910
16900
37040
27320
29100
21460
25530
5740
20420 4590
25530
5740
18
API STANDARD 660
Table 2—Nozzle Allowable Forces and Moments at the Nozzle Neck to Shell/Channel Interface (Continued)
Nominal
Diameter
DN (NPS)
350
400
450
500
600
14
16
18
20
24
Flange
Rating
Mx
My
Mz
Fx
Fy
Fz
N·m
(lbf·ft)
N·m
(lbf·ft)
N·m
(lbf·ft)
N
(lbf)
N
(lbf)
N
(lbf)
150
11510
8490
18610
13720
14620
10780
11690
2630
9350
2100
11690
2630
300
16120
11890
26050
19210
20470
15100
16350
3680
13080 2940
16350
3680
600
23020
16980
37210
27440
29240
21560
23370
5250
18690 4200
23370
5250
900
29930
22070
48380
35680
38010
28030
30370
6830
24290 5460
30370
6830
1500
41430
30560
66980
49400
52630
38810
42040
9450
33630 7560
42040
9450
2500
50640
37350
81860
60370
64320
47440
51380 11550 41100
9240
51380 11550
150
12030
8870
19440
14340
15280
11270
14240
3200
11390
2560
14240
3200
300
21050
15520
34020
25090
26730
19720
24920
5600
19930 4480
24920
5600
600
30070
22170
48600
35840
38190
28160
35590
8000
28470 6400
35590
8000
900
42090
31040
68040
50180
53460
39430
49830 11200 39860 8960
1500
48100
35480
77760
57350
61100
45060
56940 12800 45550 10240 56940 12800
2500
51110
37690
82620
60930
64920
47880
60500 13600 48400 10880 60500 13600
150
15220
11230
24610
18150
19340
14260
16030
3600
12820 2880
16030
3600
300
26640
19650
43060
31760
33830
24950
28030
6300
22420 5040
28030
6300
600
38050
28060
61510
45360
48330
35640
40040
9000
32030 7200
40040
9000
900
49470
36480
79970
58970
62830
46340
52050 11700 41640 9360
1500
60880
44900
98420
72580
77330
57030
64070 14400 51250 11520 64070 14400
2500
64690
47700
104570
77120
82160
60590
68070 15300 54450 12240 68070 15300
150
18790
13860
30380
22400
23870
17600
17800
4000
14240 3200
17800
4000
300
32890
24250
53160
39200
41770
30800
31140
7000
24910 5600
31140
7000
600
42280
31180
68350
50400
53700
39600
40040
9000
32030 7200
40040
9000
900
61070
45040
98720
72800
77570
57200
57830 13000 46260 10400 57830 13000
1500
70460
51960
113910
84000
89500
66000
66730 15000 53380 12000 66730 15000
2500
79860
58890
129100
95200
101430
74800
75630 17000 60500 13600 75630 17000
150
33820
24950
54680
40320
42960
31680
26700
6000
21360 4800
26700
6000
300
47350
34920
76550
56450
60150
44360
37380
8400
29900 6720
37380
8400
600
67640
49890
109350
80640
85920
63360
53390 12000 42710 9600
900
87940
64850
142160 104840 111700
82370
69400 15600 55520 12480 69400 15600
1500
121760
89790
196830 145160 154650 114050
96090 21600 76870 17280 96090 21600
2500
148810 109740 240570 177410 189020 139400 117440 26400 93950 21120 117440 26400
49830 11200
52050 11700
53390 12000
SHELL-AND-TUBE HEAT EXCHANGERS
19
7.6.11 Reinforcement pads shall not be used for nozzles in cyclic service, hydrogen service with operating
temperatures above 230 °C (450 °F), or other services with operating temperatures above 400 °C (750 °F).
7.6.12 The maximum allowable working pressure shall not be limited by nozzle reinforcement.
7.7 Flanged External Girth Joints
● 7.7.1 Channel and shell external girth joints shall be of through-bolted construction. Studded-in bolts may be used
when specified or approved by the Purchaser.
7.7.2 Flanges for external girth joints shall be of the forged welding-neck type, unless otherwise specified or
approved by the purchaser.
7.7.3 Nubbins shall not be used.
7.7.4 The design clearance between mating flanges shall not be less than 3 mm (1/8 in.) at the periphery of the
flanged joint. After assembly of the girth flange joint, the measured clearance between the mating flanges shall not be
less than 1.5 mm (1/16 in.). The clearance between flanges shall extend within the bolt circle to allow flanges to be
checked for radial distortion caused by an excessive bolt load.
7.7.5 Spot facing or back facing of the bolting bearing surfaces shall be in accordance with ASME B16.5 and the
pressure design code.
● 7.7.6 Hydraulic bolt tensioning shall be applied for all bolt diameters equal to or greater than 50 mm (2 in.), or in
hydrogen service where bolt diameters are equal to or greater than 40 mm (11/2 in.), or when specified by the
purchaser. Alternate forms of tightening followed by bolt elongation verification (e.g. hydraulic torquing in combination
with ultrasonic extensometer measurement) may be considered in lieu of tensioning, with approval of the purchaser.
7.7.7 When bolt tensioning is used, the bolting shall have additional thread length equivalent to one bolt diameter,
extending from the nut at one end, to allow attachment of the bolt-tightening device.
● 7.7.8 When bolt tensioning is used, the purchaser shall specify any special requirements necessary to allow for
adequate clearance for the bolt-tightening device.
7.7.9 When either manual or hydraulic torquing is applied, through-hardened washers shall be provided under nuts
for all bolts to improve the translation of torque into bolt preload by providing a smooth and low friction bearing surface
for the nut, and to protect the contact surface of the flange from damage caused by a turning nut.
7.7.10 Washers shall conform to the requirements of ASME PCC-1, Appendix M. The washers shall be suitable for
re-use as defined in ASME PCC-1, Appendix M, unless otherwise specified by the purchaser.
7.7.11 Stationary tubesheet flange assembly shall be designed with the same type of gasket on the tube side and
shell side.
7.7.12 Allowable stresses that have been established on the basis of short-time tensile strength shall not be used
for the design of girth flanges, gasketed tubesheets, and gasketed flat covers.
NOTE
In ASME BPVC, Section II, the allowable stresses of some high nickel alloys have been established in this way. These
stress values may result in dimensional changes due to permanent strain and shall not be used for flanges for gasketed joints
where slight distortion can cause leakage.
7.7.13 Flange design shall be in accordance with the pressure design code.
7.7.14 The maximum allowable working pressure shall not be limited by flange bolting.
20
API STANDARD 660
● 7.7.15 When specified by the purchaser, external girth flanges shall be provided with 3 mm (1/8 in.) future machining
allowance on the gasket contact seating surface (including pass-partition surfaces). The additional thickness shall not
be used in the calculation of maximum allowable working pressure.
NOTE
This requirement does not apply to clad or weld overlay construction.
7.7.16 Tongue and groove type configuration shall not be used, unless specified or agreed by the purchaser.
7.8 Girth Flange Joint Supplementary Design Requirements
● 7.8.1 The joint component approach, as defined in ASME PCC-1, Appendix O, and the requirements contained
within this section, shall be applied to one or both sides of the heat exchanger, when specified by the purchaser.
Definition of terms and symbology contained within this section are consistent with ASME PCC-1. See A.4.5 for
additional guidance.
7.8.2 The minimum permissible bolt stress, Sbmin, and the maximum permissible bolt stress, Sbmax, shall be 40 %
and 70 %, respectively, of the listed yield values in the pressure design code at assembly conditions (i.e. ambient
temperature).
7.8.3 At least one-half of the gasket pass-partition rib area shall be added to the peripheral ring gasket area, Ag,
unless otherwise agreed with the purchaser.
7.8.4 The selected assembly bolt stress, Sbsel, shall be established so as to ensure that the gasket stresses comply
with Table 3. For gasket types not listed, the minimum and maximum gasket stresses shall be agreed between the
purchaser and vendor.
7.8.5 The fraction of gasket load remaining after relaxation,ϕg, used in the calculations shall be 0.7, unless
otherwise specified by the purchaser.
7.8.6 To minimize potential for flange rotation, the rigidity index as calculated in ASME BPVC, Section VIII
Division 1, Mandatory Appendix 2, shall not exceed 1.0.
7.8.7 For stationary tubesheets with gaskets on both the shell and tube sides of the tubesheet, in Step 6 of
ASME PCC-1, the following additional checks, as calculated by Equation (1) and Equation (2), shall be undertaken to
verify that the selected assembly bolt stress include the effects of pressure acting from the opposing side of the
tubesheet. In this case, the maximum design pressure, Pmax, shall be taken as the design pressure difference
between the two sides.
Table 3—Assembly Gasket Stress
Maximum Permissible
Gasket Stress, Sgmax
MPa (psi)
Minimum Gasket Seating
Stress, Sgmin-S
MPa (psi)
Minimum Gasket Operating
Stress, Sgmin-O
MPa (psi)
Grooved metal with soft facing
380 (55,000)
140 (20,000)
97 (14,000)
Corrugated metal with soft facing
275 (40,000)
140 (20,000)
97(14,000)
b
140 (20,000)
97 (14,000)
Peripheral Gasket Typea
Spiral-wound
a
These stresses are based on the use of facing layers or filler materials, such as flexible graphite, PTFE, or other conformable materials, and
excludes core materials of carbon steel, brass, copper, or aluminum alloys.
b
The maximum permissible gasket stress does not apply when a means to prevent over-compression of the gasket is employed
(e.g. centering rings with spiral-wound gaskets).
SHELL-AND-TUBE HEAT EXCHANGERS
21
Step 6a: Check selected assembly bolt stress is adequate for the shell side gasket:
π
2
( Sg min-o × A g,S ) + --- × ( G ID,S ) × ( P S – P T )
4
Sb sel ≥ ------------------------------------------------------------------------------------------------------( ϕg × nb × Ab )
(1)
Step 6b: Check selected assembly bolt stress is adequate for the tube side gasket:
π
2
( Sg min-o × A g,T ) + --- × ( G ID,T ) × ( P T – P S )
4
Sb sel ≥ ------------------------------------------------------------------------------------------------------( ϕg × nb × Ab )
(2)
where
Ag,S
is the shell side gasket area, expressed in mm2 (in.2);
Ag,T
is the tube side gasket area, expressed in mm2 (in.2);
GID,S
is the shell side gasket inner diameter, expressed in mm (in.);
GID,T
is the tube side gasket inner diameter, expressed in mm (in.);
nb
is the number of bolts;
PS
is the design pressure on the shell side, expressed in MPa (psi);
PT
is the design pressure on the tube side, expressed in MPa (psi);
Sbsel
is the selected assembly bolt stress, expressed in MPa (psi);
Sgmin-o
is the minimum gasket operating stress, expressed in MPa (psi);
φg
is the fraction of gasket load remaining after relaxation.
7.8.8 If the requirements contained within this section require the bolt area to be increased or gasket geometry
revised, then the pressure design code calculations shall be updated and the required flange thickness re-calculated
accordingly.
7.8.9 Controlled bolt-tightening procedures shall be applied, and records provided, to demonstrate that the selected
assembly bolt stress, Sbsel, has been achieved.
7.9 Expansion Joints
7.9.1 Expansion joints in shells shall be thin-wall bellows or thick walled (e.g. flanged, or flanged and flued). Floating
head tail pipe expansion joints shall be thin wall bellows type.
7.9.2 Expansion joints made of thin-walled bellows shall:
a) be protected from internal damage with a metallic liner mounted flush with the inside of the shell. The liner
material shall be compatible with the base material to which it is attached. Carbon steel liners shall be at least
22
API STANDARD 660
6 mm (1/4 in.) thick. Liners of stainless steel or other alloys shall be at least 3 mm (1/8 in.) thick. For vertically
mounted bellows, the liner shall be attached at the top and open at the bottom to allow for free drainage;
b) be protected from external damage with a metallic cover that is designed to remain intact during shipping,
handling, and operation;
c) be designed to meet the requirements of the pressure design code. In no case shall the cycle life as calculated by
EJMA be less than 1000 normal operating cycles;
d) have the bellows formed from a cylinder having only a single longitudinal weld that shall be 100 % radiographed
before forming. The acceptance criteria shall comply with the pressure design code;
e) have bellows welds that are 100 % examined by the liquid-penetrant method including attachment welds. The
acceptance criteria shall comply with the pressure design code;
f) be designed with stays to prevent damage during shipping and handling. Stays that require removal or adjustment
prior to operation must be clearly identified;
g) for internal floating-head tailpipe expansion joints, be fitted with permanent stays that prevent damage during
maintenance and hydrostatic testing with the shell cover removed. The stays shall permit the expansion joint’s full
design movements.
7.10 Gaskets
7.10.1 Flanged external girth joint gaskets and floating-head gaskets in hydrocarbon or steam service shall be
double-jacketed metal with soft gasket filler, spiral-wound, grooved metal with soft gasket-seal facing, or corrugated
metal with soft gasket-seal facing. Solid metal gaskets shall only be used with welded closures or self-energizing
closures. See A.4.6 for additional guidance.
NOTE
The term grooved is synonymous with the term serrated as applied to gasket type.
7.10.2 Double-jacketed gaskets shall not be used for the peripheral portion of the gasket in the following services:
a) hydrogen service;
b) operating temperatures above 205 °C (400 °F);
c) cyclic service;
d) sour or wet hydrogen sulfide service;
e) design pressure equal to or greater than 2050 kPa (ga) (300 psig);
f) shell diameter greater than 1200 mm (48 in.).
7.10.3 Pass-partition rib(s) shall be of the same material grade as the peripheral portion of the gasket.
7.10.4 Pass-partition ribs shall not be made from flat solid metal.
7.10.5 Pass-partition ribs shall be designed and constructed such that they do not inhibit the compression or seating
of the peripheral portion of the gasket.
SHELL-AND-TUBE HEAT EXCHANGERS
23
7.10.6 If the gasket OD is less than or equal to 610 mm (24 in.), the peripheral portion shall be of one piece (nonwelded) construction. If the gasket OD exceeds 610 mm (24 in.), the maximum quantity of welds in the peripheral
portion shall not exceed the following:
a) for double jacketed gaskets, one;
b) for other gasket types, the greater of either two, or the ratio of gasket OD/610 mm (gasket OD/24 in.).
7.10.7 The gasket welds shall be as follows.
a) The welds in the peripheral portion of the gasket shall be continuous and full-penetration. The cross-section,
finish, and flatness of these welded areas must match the remainder of the peripheral gasket.
b) The welds shall not inhibit the sealing or compression of the peripheral gasket or pass ribs.
7.10.8 When adhesives are used to bond facing materials (e.g. graphite) to grooved and corrugated metal gaskets,
they shall be compatible with the metal core (e.g. chloride content).
7.10.9 Double jacketed gaskets shall be as follows.
a) They shall be manufactured with the filler material completely enclosed in metal.
b) Filler materials shall be selected to ensure no degradation occurs during manufacturing (e.g. welding).
7.10.10 Grooved metal gaskets shall be as follows.
a) The top of the serrations at the weld shall be flat in comparison with the rest of the gasket. The grooves shall be
dressed to match the standard profile.
b) Thickness variations in the metallic core, after completion of gasket fabrication, shall not exceed 0.13 mm
(0.005 in.).
c) Where the outside diameter is less than 1 m (40 in.), they shall be manufactured with one-piece continuous facing
materials (no joints). Facing joints in larger-diameter gaskets shall include a 1.5 mm (1/16 in.) to 3 mm (1/8 in.)
overlap of the facing material; however, butt joints (gap free) are allowed for flexible graphite facings. Facing joints
shall not be coincident with a facing joint on the opposite sealing face, or with any welds in the core.
7.10.11 Corrugated metal gaskets shall be as follows:
a) minimum core thickness of 0.46 mm (0.018 in.);
b) minimum width of 12 mm (1/2 in.);
c) corrugations in the weld area that match the gasket profile;
d) where the outside diameter is less than 1 m (40 in.), they shall be manufactured with one-piece continuous facing
materials (no joints). Facing joints in larger-diameter gaskets shall include a 1.5 mm (1/16 in.) to 3 mm (1/8 in.)
overlap of the facing material; however, butt joints (gap free) are allowed for flexible graphite facings. Facing joints
shall not be coincident with a facing joint on the opposite sealing face or with any welds in the core.
7.10.12 Spiral-wound gaskets shall be provided with a flat inner ring to prevent over-compression and inward radial
buckling. For flanges on shells with a diameter greater than 1000 mm (40 in.), or when the gasket is not confined on
its OD, an outer metal ring shall also be provided. See A.4.6 for additional guidance.
7.10.13 The maximum gasket width shall be 50 mm (2 in.), except for non-metallic sheet type gaskets.
24
API STANDARD 660
7.11 Handling Devices
7.11.1 The lifting device shall be a weld-on lug or ring provided with a hole not less than 38 mm (11/2 in.) in diameter.
Wherever possible, the lug or ring shall be located at the top of the component, above its center of gravity; otherwise,
two suitably located lugs or rings shall be provided. The lifting device shall be designed to support at least twice the
mass of the component.
7.11.2 For stacked heat exchangers, two lifting lugs or rings shall be provided on all covers, located at the top,
approximately 45° from the vertical centerline.
7.11.3 Stationary tubesheets shall be provided with pulling lugs or tapped holes on their outer face for the insertion
of eyebolts to aid removal of the tube bundle from the shell. Pulling lugs and tapped holes shall be designed for a
pulling force equal to at least 150 % of the tube bundle mass. Each tapped hole shall be fitted with a threaded plug of
the same material as the tubesheet face. The exposed section of the plug shall be at least 50 mm (2 in.) long.
7.11.4 All vertical heat exchangers shall be provided with lifting devices for the entire heat exchanger. The lifting
devices shall be provided above the center of gravity of the heat exchanger.
7.12 Requirements for Hydrogen Service
7.12.1 Totally enclosed spaces between attachment welds and the pressure boundary shall be eliminated or vented
with a hole of 6 mm (1/4 in.) in diameter.
● 7.12.2 The purchaser shall specify any supplemental requirements for low chrome steels in high temperature or
high pressure hydrogen service (e.g. API RP 934-A, API RP 934-C).
NOTE
See A.4.7 for information on the potential for leaks resulting from bolting relaxation.
8 Materials
8.1 General
8.1.1 Castings shall not be used, unless approved by the purchaser.
8.1.2 Material for external parts that are welded directly to the heat exchanger, such as pads, brackets, and lugs,
shall be of the same nominal composition as the material to which they are welded.
8.1.3 If alloy linings are specified by the purchaser, they shall be weld overlay, integrally-clad, or explosion-bonded.
Loose liners or sleeves shall not be used without the approval of the purchaser.
● 8.1.4 Purchaser shall specify materials for all components, including bolting and gaskets.
8.1.5 Tubesheets that are welded to the adjacent shell or channel cylinder by use of a corner joint can be provided
as forged or plate materials. If plate material is used, it shall be 100 % ultrasonically examined for laminations and
other defects prior to attachment to the cylinder.
8.2 Requirements for Carbon Steel in Sour or Wet Hydrogen Sulfide Service
8.2.1 Materials shall be supplied in the normalized condition, unless otherwise approved by the purchaser. The
acceptability of hot-formed material shall be subject to approval of the purchaser.
8.2.2 Pressure-retaining components shall be supplied with a Certified Material Test Report (CMTR). The CMTR
shall include the unspecified elements chromium (Cr), columbium (Cb) [also known as niobium (Nb)]), nickel (Ni),
SHELL-AND-TUBE HEAT EXCHANGERS
25
vanadium (V), molybdenum (Mo), and copper (Cu) that are used in the formula to calculate the carbon equivalent
(CE) as defined by NACE MR0175 (all parts) or NACE MR0103.
● 8.2.3 The maximum allowable carbon equivalent shall be agreed with the purchaser prior to purchase of materials
for use in fabrication. Restrictions on other residual elements and micro-alloying elements can also apply depending
on the severity of the service. The purchaser shall specify all such restrictions.
8.3 Gaskets
8.3.1 Gaskets shall not contain asbestos.
8.3.2 Material for metal-jacketed, grooved-metal, corrugated-metal, or solid-metal gaskets shall have a corrosion
resistance at least equal to that of the gasket contact surface material.
8.3.3 Metal windings of spiral-wound gaskets shall be of austenitic stainless steel, unless otherwise specified or
approved by the purchaser. Where materials of construction are a higher alloy, then the metal windings shall be the
same alloy material.
8.3.4 Grooved, or metal–jacketed gaskets, shall be softer than the gasket contact surface.
8.3.5 Gasket material, including filler and facing material, shall be selected to withstand the maximum design
temperature. See A.5.1 for additional information on gasket material.
8.3.6 Compressed sheet type gaskets shall not be used in hydrocarbon, steam, hydrogen, sour or wet hydrogen
sulfide service.
8.4 Tubes
8.4.1 Integrally finned tubes of copper alloy shall be furnished in the annealed-temper condition, such as described
in ASTM B359/B359M.
8.4.2 All welded tubes shall be eddy-current tested in the finished condition over their full length.
9 Fabrication
9.1 Shells
9.1.1 All longitudinal and circumferential welds of shells for other than kettle-type heat exchangers shall be finished
flush with the inner contour for ease of tube bundle insertion and withdrawal. For kettle-type heat exchangers, this
requirement shall not apply to welds in the enlarged section, unless they are in the bottom quadrant of the shell. See
A.6.1 for additional guidance.
9.1.2 For removable-bundle heat exchangers, the permissible out-of-roundness of a completed shell, after all
welding and any required heat treatment, shall allow a metal template to pass through the entire shell length without
binding. The template shall consist of two rigid disks (each with a diameter equal to the diameter of the transverse
baffle or support plate) rigidly mounted perpendicularly on a shaft and spaced not less than 300 mm (12 in.) apart.
9.1.3 Transverse baffle-to-shell clearances greater than those indicated in TEMA, Table RCB-4.3, shall not be used,
unless approved by the purchaser.
26
API STANDARD 660
9.2 Pass-partition Plates
Pass-partition plates for forged or welded channels and floating-heads shall be welded full length, either from both
sides or with full-penetration welds, except for special designs approved by the purchaser. If welded from both sides,
the first 50 mm (2 in.) from the gasket face shall be full-penetration welds.
9.3 Connection Junctions
Nozzles and couplings shall not protrude beyond the inside surface of the shell, channel, or head to which they are
attached.
9.4 Tubes
9.4.1 All tubes, including U-tubes, shall be formed from a single length and shall have no circumferential welds,
unless approved by the purchaser.
9.4.2 No tubes or tube holes shall be plugged without notifying the purchaser. The method and procedure of
plugging shall be subject to approval of the purchaser.
9.5 Welding
9.5.1 Welds can be made by any welding process other than oxyacetylene gas welding.
9.5.2 Category A and B welded joints shall be full-penetration welds.
9.5.3 All welds attaching connections to cylinders or to heads shall fully penetrate the total thickness of the
component wall or the connection wall forming the attachment.
9.5.4 Backing strips that remain in place on the inside of a component after completion of welding shall not be used,
unless approved by the purchaser.
9.5.5 The method used to position a tube in advance of tube-end welding shall be done in such a way as to prevent
the trapping of gases during the welding process.
9.5.6 Strength-welded tube-to-tubesheet welds shall have a minimum of two weld passes and be produced by gas
tungsten arc welding (GTAW) using filler material, unless otherwise specified or approved by the purchaser.
9.5.7 The qualification of the weld procedure for a strength-welded tube-to-tubesheet joint shall be in accordance
with the requirements of the pressure design code, with the following additional requirements.
a) The minimum leak path (i.e. the distance from the root of the weld to the surface nearest to the root) shall not be
less than two-thirds of the nominal tube wall thickness.
b) A minimum of three tensile pull-tests shall be performed on the qualification test coupon whenever it cannot be
proven by calculation that the strength of the weld is greater than the axial strength of the tube.
9.5.8 Welds attaching nonpressure external attachments (such as lugs or structural steel supports) shall be
continuous, except for insulation support rings.
9.5.9 Repair-associated welding procedures shall be submitted to the purchaser for review before the start of repair.
9.5.10 Full-penetration welds shall be used for all internal attachments to the pressure boundary components that
will be exposed to hydrogen service.
SHELL-AND-TUBE HEAT EXCHANGERS
27
● 9.5.11 The purchaser shall specify whether weld procedure qualifications for carbon steel in sour or wet hydrogen
sulfide service, including tube-to-tubesheet welds, shall include a micro-hardness survey performed on a weld crosssection, including the heat affected zone (HAZ), and transverse to the weld centerline. The micro-hardness testing
and acceptance criteria shall be in accordance with NACE SP0472 or NACE MR0175 (all parts), as applicable. Any
additional restrictions on residual elements or micro-alloying elements for the qualification test material shall be
specified by the purchaser.
● 9.5.12 When specified by the purchaser, weld procedure qualifications for duplex stainless steels, including tube-totubesheet welds, shall include a micro-hardness survey performed on a weld cross-section (including HAZ) and
transverse to the weld centerline. The micro-hardness testing and acceptance criteria shall be as agreed with the
purchaser.
NOTE
See API TR 938-C and API RP 582 for guidance on welding of duplex stainless steels.
9.6 Heat Treatment
9.6.1 Machined contact surfaces, including any threaded connections, shall be suitably protected to prevent scaling
or loss of finish during heat treatment.
● 9.6.2 The purchaser shall specify if heat treatment is required after bending of U-tubes for process reasons.
9.6.3 Unless otherwise specified by the purchaser, the following shall be subject to heat treatment after tube
bending:
a) Carbon steel, carbon-molybdenum, and low chromium steel U-bends (C - 0.5 % Mo through 5 % Cr steels) in
sour or wet hydrogen sulfide service.
b) U-bends in brass alloys (e.g. per ASME SB-395/395M).
c) Unstabilized austenitic stainless steels with a mean radius smaller than 5 times the nominal outside diameter of
the tube.
9.6.4 Unstabilized austenitic stainless steel tubing subjected to heat treatment after bending shall be supplied with
0.05 % maximum carbon content or be dual certified as low carbon grade.
● 9.6.5 For ferritic and martensitic stainless steels, stabilized austenitic stainless steels, duplex stainless steels,
copper, copper-nickel, and high nickel alloys (Ni > 30 %), heat treatment of U-tubes shall be applied if cold working
can induce susceptibility to stress corrosion. The purchaser shall specify when heat treatment is required in such
cases.
NOTE
See API TR 938-C for guidance on heat treatment of duplex stainless steel U-bends.
9.6.6 U-bend heat treatment shall be in accordance with the pressure design code. When applied, U-bend heat
treatment shall be completed by electric resistance or furnace methods. Open flame heat treatment is not permitted.
The procedure used for heat treatment shall be agreed between the purchaser and vendor.
9.6.7 For electric resistance or induction heating, the heat-treated portion of the U-bend shall extend at least
150 mm (6 in.) beyond the tangent point. For furnace heating, the heat treatment shall extend at least 600 mm (24 in.)
beyond the tangent point.
● 9.6.8 When specified by the purchaser, the heat treated portion of U-tubes shall receive a de-scaling treatment.
28
API STANDARD 660
9.6.9 Postweld heat treatment of fabricated carbon steel and low-alloy (maximum 9 % chromium) steel channels
and bonnets shall be performed for the following:
a) channels and bonnets with six or more tube passes;
b) channels and bonnets whose nozzle-to-cylinder internal diameter ratios are 0.5 or greater, except where a conical
reducer is used in place of the channel or bonnet.
● 9.6.10 The purchaser shall specify if postweld heat treatment is required for weld-overlaid channels and bonnets.
9.6.11 Postweld heat treatment shall be performed for all carbon steel and low-alloy (maximum 9 % chromium)
steel floating-head covers that are fabricated by welding a dished-only head into a ring flange.
● 9.6.12 The purchaser shall specify if postweld heat treatment of shell side or tube side components is required for
process reasons.
9.6.13 For sour or wet hydrogen sulfide service, the minimum postweld heat treatment requirements for carbon
steel construction shall be in accordance with NACE SP0472. The minimum hold time shall be in accordance with the
pressure design code, or 1 h, whichever is greater.
9.7 Dimensional Tolerances
9.7.1 Manufacturing tolerances shall be such that nominally identical parts are interchangeable.
9.7.2 Heat exchangers that will be stacked in series shall be stacked in the shop to check connection alignment.
9.7.3 For stacked heat exchangers, mating nozzle flanges shall not be out-of-parallel with each other by more than
1 mm (1/32 in.), measured across any diameter. Separation of mating nozzle flanges shall not exceed 3 mm (1/8 in.)
after installation of the gasket. Bolts shall be capable of being inserted and removed freely without binding. Shims
shall be installed as required between the supports and shall be tack-welded in place.
9.7.4 Flattening tolerances after bending of U-tubes shall not exceed 10 % of the tube outside diameter.
9.8 Gasket Contact Surfaces Other Than Nozzle Flange Facings
9.8.1 Gasket contact surfaces shall have finishes as shown in Table 4.
9.8.2 The flatness tolerance (maximum deviation from a plane) on peripheral gasket contact surfaces shall be
0.8 mm (1/32 in.).
Table 4—Gasket Contact Surface Finishes
Type
Solid flat metal gaskets
Double jacketed gaskets
Surface Roughness
Raa
1.6 (63)b maximum
1.6 to 3.2 (63 to 125)
Spiral-wound gaskets
3.2 to 6.3 (125 to 250)
Grooved or corrugated metal gaskets with soft gasket-seal facing
a
Ra is roughness average.
b
Dimensions are in micrometers (micro-inches).
SHELL-AND-TUBE HEAT EXCHANGERS
29
9.8.3 The flatness tolerances on peripheral gasket contact surfaces shall be as specified in Table 5 when any of the
following apply:
a) steam service, with operating pressures above 1035 kPa (ga) (150 psig);
b) hydrogen service;
c) operating temperatures above 205 °C (400 °F);
d) cyclic service;
e) sour or wet hydrogen sulfide service;
f) design pressure equal to or greater than 6900 kPa (ga) (1000 psig);
g) shell diameter greater than 1200 mm (48 in.);
h) when specified by the purchaser.
Table 5—Flatness Tolerance on Peripheral Gasket Contact Surfaces
Dimensions in millimeters (inches)
Heat Exchanger Nominal Diameter
Tolerance
< 375 (15)
± 0.08 (0.003)
375 to 750 (15 to 30)
± 0.15 (0.006)
751 to 1125 (31 to 45)
± 0.20 (0.008)
> 1125 (45)
± 0.20 (0.008)
9.8.4 The flatness of gasket contact surfaces shall be measured with a dial gauge. However, the flatness of the
pass-partition grooves and mating pass-partition plate edges can be measured with a straight edge.
9.8.5 Pass-partition plates and grooves shall be designed and constructed such that they do not inhibit the
compression or seating of the peripheral gasket. The difference in height between the pass-partition surface and the
peripheral gasket contact surface of the flange face shall be +0.15 mm −0.65 mm (+0.006 in. −0.025 in.).
9.8.6 Flange flatness tolerance and surface finish shall be measured after the flange has been welded to the
component cylinder or the cover and after any postweld heat treatment.
9.8.7 The flatness of tubesheet gasket-contact surfaces shall be measured after the tube-to-tubesheet joints have
been completed, including any heat treatment.
9.9 Tube Holes
9.9.1 Tube hole grooves shall be square-edged, concentric, and free from burrs.
9.9.2 If austenitic stainless steel, duplex stainless steel, titanium, cupronickel, or nickel alloy tubes are specified, the
tube holes shall be machined in accordance with TEMA, Table RCB-7.21, column (b) (Special Close Fit).
9.10 Tube-to-Tubesheet Joints
9.10.1 If roller-expanded joints are utilized, the tube wall thickness reduction shall be in accordance with Table 6.
30
API STANDARD 660
Table 6—Maximum Allowable Tube Wall Thickness Reduction for Roller-expanded
Tube-to-Tubesheet Joints
Material
Maximum Tube Wall Thickness Reduction
%
Carbon steel and low-alloy (max. 9 % chromium) steel
8a
Stainless and high alloy steel
6a
Duplex stainless steels
b
Titanium and work hardening nonferrous
5a
Nonferrous non-work hardening (e.g. admiralty brass)
8a
a
These can be increased by a further 2 %, if approved by the purchaser.
b
To be agreed between purchaser and vendor. Tube expansion may increase hardness significantly. For more
information, see API TR 938-C.
9.10.2 If welded-and-expanded joints are specified, tube wall thickness reduction should begin at least 6 mm (1/4 in.)
away from welds.
9.10.3 The minimum length of expansion shall be in accordance with TEMA Section 5, Paragraph RCB-7.1.
However, in no case shall the expansion extend within 3 mm (1/8 in.) of the shell side face of the tubesheet.
● 9.10.4 For shell side clad (or weld overlay) tubesheets, the tube shall be expanded to seal against the cladding
material for a minimum distance of 6 mm (1/4 in.). The purchaser shall specify if a groove is required within the shell
side cladding.
9.10.5 For tube side clad (or weld overlay) tubesheets with either strength-welded or seal-welded and expanded
tube-to-tubesheet joints, tube hole grooves, when provided, shall be located in the base material and not in the
applied cladding or weld overlay.
9.10.6 For welded-and-expanded tube-to-tubesheet joints requiring postweld heat treatment, the tubes shall be
expanded after postweld heat treatment.
9.10.7 Tubes shall be flush with or extended by no more than 5 mm (3/16 in.) beyond the face of the tubesheet,
except in vertical exchangers when tubes shall be flush with the top tubesheet, unless otherwise specified by the
purchaser.
9.11 Assembly
9.11.1 Match marks or dowels shall be provided to prevent mis-assembly of the following bolted joints:
a) floating-head cover to tubesheet;
b) channel to tubesheet;
c) grooved channel cover to channel;
d) stationary tubesheet to shell.
9.11.2 The threads of external studs and nuts shall be coated with a suitable anti-seize compound to prevent galling.
SHELL-AND-TUBE HEAT EXCHANGERS
31
10 Inspection and Testing
10.1 Quality Control
10.1.1 For pressure containing welds inspection and testing shall be performed in accordance with the pressure
design code. The following additional requirements apply.
a) At least one spot-radiograph shall be made of each accessible butt-welded joint. Nozzle-to-shell welds are exempt
from this requirement, unless required by the pressure design code.
b) Spot radiographs shall include each start and stop of welds made by the automatic submerged-arc welding
process.
c) Spot radiographs shall be at least 250 mm (10 in.) long or shall be full length if the weld is less than 250 mm
(10 in.) long.
d) Weld porosity limits for spot radiographs shall be as stated in the pressure design code for fully radiographed
joints.
e) 100 % radiographic examination shall be performed on any welded seam in any component that has been
subjected to severe working (e.g. a ratio of thickness to local radius greater than 5 %) after welding.
f) If set-on connections are used and the pressure envelope is plate, after welding of the connections, 100 %
ultrasonic examination on the attachment welds and the plate shall be completed for at least 100 mm (4 in.) from
the connection.
10.1.2 If set-on connections are used, the edge of the hole in the plate to which the connections are attached shall
also be examined by the magnetic-particle or liquid penetrant method prior to welding. Subject to agreement with the
purchaser, indications found shall be cleared to sound metal and then repair-welded.
10.1.3 The magnetic-particle examination method, extent, and acceptance criteria shall comply with the pressure
design code.
10.1.4 For nonmagnetic materials, a liquid-penetrant examination shall be used in place of any required
magnetic-particle examination.
10.1.5 The liquid-penetrant examination method, extent, and acceptance criteria shall comply with the pressure
design code.
10.1.6 Production weld-hardness testing of pressure-retaining welds shall be in accordance with the pressure
design code, or the following requirements, whichever is the more stringent.
a) Welds in components made of carbon, Cr-Mo, 11/13/17 % chromium steels, and duplex stainless steels shall be
hardness tested. Hardness testing of the heat affected zone shall be conducted if required by the pressure design
code, or when specified by the purchaser.
b) If postweld heat treatment is required, examination shall be made after the post-weld heat treatment is completed.
c) Unless otherwise agreed between the vendor and purchaser, the weld hardness shall not exceed the values listed
in Table 7.
d) Hardness readings shall be taken with a portable Brinell hardness tester. Other hardness testing techniques can
be employed if approved by the purchaser. When access is available, tests shall be performed on the side of the
weld in contact with the process fluid.
32
API STANDARD 660
Table 7—Hardness Limits
Material
Maximum Weld Hardness
Carbon Steel
225 HBW
Chromium Steel (up to 3 % Cr)
225 HBW
Chromium Steel (5 % Cr to 17 % Cr)
241 HBW
Duplex Stainless Steel (22 % Cr)
to be agreed with purchaser
Super Duplex Stainless Steel (25 % Cr)
to be agreed with purchaser
NOTE These hardness values are for general services. More stringent hardness testing and acceptance
criteria can be required for special services (e.g. sulfide stress cracking or other types of environmental
cracking services as specified in NACE Standards).
e) One longitudinal weld, one circumferential weld, and each connection-to-component weld if the connection is
DN 50 (NPS 2) or larger, shall be tested.
f) If more than one welding procedure is used to fabricate longitudinal or circumferential welds, hardness readings
shall be made on welds deposited by each procedure.
g) Hardness test results and locations shall be recorded.
10.1.7 At welded joints in alloy-clad construction, the weld in the base metal and the area adjacent to the weld
where the cladding has been stripped back shall be examined by magnetic-particle or liquid-penetrant inspection
before weld overlay of the joint.
10.1.8 All finished carbon steel welds where postweld heat treatment is specified for process reasons (e.g. to
prevent environmental cracking), and low-alloy steel welds in all services, shall be examined after postweld heat
treatment (unless the pressure design code specifies examination after hydrostatic testing) by the magnetic-particle
method. The wet-fluorescent method shall be used to inspect accessible process-wetted surfaces of welds and heat
affected zones in sour or wet hydrogen sulfide service.
10.1.9 Final welds in all nonmagnetic materials, whether of solid alloy or alloy-clad plate and all bimetallic welds
between nonmagnetic and magnetic materials shall be examined by the liquid-penetrant method after any required
postweld heat treatment.
10.1.10 A final visual weld inspection shall be performed after any postweld heat treatment.
10.1.11 After cladding, but prior to fabrication, integrally-clad material shall be subjected to an ultrasonic
examination from the clad side in accordance with the pressure design code.
10.1.12 Overlay weldments, back-cladding, and attachment welds to overlay weldments shall be liquid-penetrant
examined after any postweld heat treatment.
10.1.13 For duplex stainless steel pressure retaining welds, bimetallic welds using austenitic stainless steel filler
metal, and the final weld overlay layer in duplex or austenitic stainless steels, the ferrite content of all accessible
completed production welds shall be measured prior to any postweld heat treatment.
10.1.14 For austenitic stainless steel pressure retaining welds, requirements for any ferrite testing shall be specified
by the purchaser.
SHELL-AND-TUBE HEAT EXCHANGERS
33
10.1.15 When ferrite testing is applied, a minimum of three tests shall be made on each 1.5 m (5 ft) of weld, with at
least three tests made on each circumferential seam, three tests on each longitudinal weld seam, and three tests on
each nozzle weld. The acceptance criteria for the minimum and maximum ferrite content shall be agreed between the
purchaser and vendor.
● 10.1.16 The purchaser shall specify whether all carbon steel plate in sour or wet hydrogen sulfide service shall be
subjected to an ultrasonic lamination check (e.g. to EN 10160 grade S2E2 or ASME SA-578, acceptance level A
supplementary requirement S1).
10.1.17 If tube-to-tubesheet joints are roller expanded (not welded), the tube wall thickness reduction shall be
randomly checked and recorded. A minimum of 2 % of the joints per tube bundle, with a minimum of 5 joints, shall be
checked (see 9.10.1).
10.1.18 When weld deposit overlay is applied on pressure retaining components, production weld chemistry tests
shall be performed at the specified depth as follows.
a) Weld overlay test samples (including weld overlay restoration) shall be taken at a depth of at least 1.5 mm
(1/16 in.) from the finished surface, unless otherwise specified by the purchaser.
b) When weld overlay is applied to the surface of exchanger shell or channel cylinders, at least two deposit analyses
shall be made for every 10 m2 (100 ft2) of overlay surface, or fraction thereof, for each welding procedure applied.
The analysis shall be taken from each end of the cylinder at locations that are diametrically opposed.
c) When weld overlay is applied to the surface of formed heads, channel covers, girth and floating-head flanges and
tubesheets, at least one deposit analysis shall be made for each welding procedure used and for each component
manufactured.
d) For tubesheets that are weld overlaid on both sides, at least one deposit analysis is required on each side of the
tubesheet.
e) When weld overlay is applied on nozzle assemblies, at least one deposit analysis shall be made for each welding
procedure used. Where multiple nozzle assemblies are manufactured with the same welding procedure, the
deposit analysis shall be taken from the smallest diameter nozzle manufactured for each welding procedure.
f) When weld overlay is applied to restore the clad area of weld joints between integrally clad components, at least
one deposit analysis shall be taken per welding procedure for each main longitudinal or circumferential weld
seam.
g) When weld overlay is applied for the surface repair of clad components or for the restoration of surfaces (other
than weld seams) where the cladding has been removed, at least one deposit analysis shall be taken for each
welding procedure used.
h) Production test locations shall be restored after testing.
10.2 Pressure Testing
10.2.1 In the case of welded-and-expanded tube-to-tubesheet joints, the tube weld integrity shall be verified before
final expansion of the tubes by a pneumatic test from the shell side at a gauge pressure of between 50 kPa (7.5 psi)
and 100 kPa (15 psi), using a soap-water solution to identify leaks.
● 10.2.2 If specified by the purchaser, tube-to-tubesheet joint integrity shall be tested after final expansion of the tubes
by a helium leak test (e.g. per ASME BPVC, Section V). See A.7 for additional guidance.
34
API STANDARD 660
10.2.3 When pneumatic testing of the tube-to-tubesheet joints from the shell side is not practical (i.e. replacement
tube bundles without shells, floating-head exchangers with integral shell heads or without test rings, etc.), the integrity
of the tube-to-tubesheet joint can be tested either by a tube side hydrostatic test or by a vacuum test of the tube
bundle.
10.2.4 Except for differential-pressure designs, an independent hydrostatic test of the shell side and the tube side
shall be performed. The minimum fluid temperature for hydrostatic testing shall be as required by the pressure design
code.
10.2.5 The water used for hydrostatic testing shall be potable and the test pressure shall be maintained for at least
1 h.
10.2.6 The chloride content of the test water used for equipment with austenitic stainless steel materials that would
be exposed to the test fluid shall not exceed 50 mg/kg (50 parts per million by mass). Upon completion of the
hydrostatic test, the equipment shall be promptly drained and cleared of residual test fluid.
● 10.2.7 Any additional requirements for equipment drying or preservation shall be specified by the purchaser.
10.2.8 The shell side hydrostatic test shall be conducted with the bonnet or channel cover removed.
10.2.9 Nozzle reinforcement pads shall be pneumatically tested between 100 kPa (ga) (15 psig) and 170 kPa (ga)
(25 psig).
10.2.10 For safety considerations, any supplementary pneumatic test shall be performed at a nominal pressure of
170 kPa (ga) (25 psig).
10.2.11 Flanged joints that have been taken apart after the final pressure test shall be reassembled with new
gaskets and re-pressure tested. Self-energizing seals can be reused, subject to approval of the purchaser.
10.2.12 Paint or other external coatings shall not be applied over welds before the final pressure test, unless
otherwise agreed by the purchaser.
10.2.13 Heat exchangers that are to be stacked in service with directly interconnecting nozzles shall be
hydrostatically tested in the stacked position.
10.3 Nameplates and Stampings
10.3.1 An austenitic stainless steel nameplate shall be permanently attached to the heat exchanger in such a
manner that it is visible after insulation has been installed.
10.3.2 The nameplate shall be located on the shell, near the channel end.
10.3.3 The following parts shall be stamped with the manufacturer’s serial number:
a) shell flange;
b) shell cover flange;
c) channel or bonnet flange;
d) channel cover;
e) stationary tubesheet;
SHELL-AND-TUBE HEAT EXCHANGERS
35
f) floating tubesheet;
g) floating-head cover flange;
h) floating-head backing device;
i) test ring flange and gland.
11 Preparation for Shipment
11.1 Protection
11.1.1 All liquids used for cleaning or testing shall be drained from heat exchangers before shipment. See A.8.1 for
additional information.
11.1.2 Heat exchangers shall be free of foreign matter prior to shipment.
11.1.3 All openings in heat exchangers shall be suitably protected to prevent damage and possible entry of water or
other foreign material.
11.1.4 All flange-gasket surfaces shall be coated with an easily removable rust preventative and shall be protected
by suitably attached durable covers of such material as wood, plastic, or gasketed steel.
11.1.5 All threaded connections shall be protected by metal plugs or caps of compatible material.
11.1.6 Connections that are beveled for welding shall be suitably covered to protect the bevel from damage.
● 11.1.7 The purchaser shall specify if there are requirements for surface preparation and protection (e.g. painting).
11.1.8 Exposed threads of bolts shall be protected with an easily removable rust preventative to prevent corrosion
during testing, shipping, and storage. Tapped holes shall be plugged with grease.
11.1.9 Tie-rods or tie-bars installed on shell expansion joints for protection during shipping shall be painted in a
contrasting color and clearly tagged to specify their removal before commissioning.
● 11.1.10 The purchaser shall specify if inert gas (e.g. nitrogen, argon) purge and fill is required. Positive pressure
shall be indicated by a pressure gage. Gages shall be suitably protected from damage during transportation. The
purchaser shall maintain the positive pressure of the inert gas during storage.
11.1.11 When an inert gas fill is used, the vendor shall apply a label or wired metal tag on all openings that states,
“Contents are under <Inert gas> pressure and must be depressurized before opening.” All transport regulations must
also be complied with.
11.2 Identification
11.2.1 The item number, shipping mass, and purchaser’s order number shall be clearly marked on the heat
exchanger.
11.2.2 All boxes, crates, or packages shall be identified with the purchaser’s order number and the item number.
11.2.3 The words “DO NOT WELD” shall be stenciled (in at least two places 180° apart) on the parts of equipment
that have been postweld heat-treated.
36
API STANDARD 660
12 Supplemental Requirements
12.1 General
● The purchaser shall specify if the additional requirements in Section 12 shall be applied to one or both sides of the
heat exchanger. These supplemental requirements should be considered by the purchaser if the cylinder thickness of
a heat exchanger component exceeds 50 mm (2 in.) or if the service is considered critical.
12.2 Design
12.2.1 The attachment of welded nozzles and other connections to components shall have integral reinforcement.
The nozzles or other connections shall be attached using full-penetration groove weld with additional fillet or butt
welds. They can be set-on, set-in, or integrally reinforced forging type inserts. Set-on type connections shall not be
welded to plate that contains laminations or other defects and shall only be used if the component is pipe or forged or
if the component plates are ultrasonically examined in the area of attachment. In this case the examination for
laminations and other defects shall be carried out for a radial distance of at least twice the thickness of the
component.
12.2.2 Tubesheet attachment welds to shell or channel cylinders shall be butt welds.
12.3 Examination
12.3.1 All material for formed heads or cylinders exceeding 50 mm (2 in.) in thickness shall be ultrasonically
examined. Non-destructive examination procedures and acceptance criteria shall comply with the pressure design
code.
12.3.2 All forgings, except standard flanges designed as described in 7.6, shall be ultrasonically examined in
accordance with the pressure design code. Non-destructive examination procedures and acceptance criteria shall
comply with the pressure design code and shall be agreed by the purchaser.
12.3.3 For ultrasonic examination of welds, plates and forgings, the purchaser shall be supplied with a report
providing diagrams of the surfaces scanned and indications obtained, the areas repaired, the nature of defects
repaired, and the repair procedures used. The following information shall also be provided:
a) pulse-echo instrument manufacturer’s name and model and the damping control setting;
b) search unit manufacturer, model, dimensions, and the substance (such as oil or water) that is used to couple the
transducer with the material being inspected;
c) frequency used and the test angle to the component's surface;
d) the wedge medium for angle-beam examination.
12.3.4 Magnetic-particle examination shall be performed on all pressure-containing plate edges and openings
before welding. Any defects found shall be removed and any necessary repairs performed. Liquid penetrant
examination shall be substituted for nonmagnetic materials.
12.3.5 Magnetic-particle examination shall be performed on all pressure-retaining welds and weld repairs, after any
postweld heat treatment. If accessible, the back side of the root pass shall be examined after being prepared for final
welding. Both sides of accessible completed welds shall be examined. Liquid penetrant examination shall be
substituted for nonmagnetic materials.
12.3.6 Magnetic-particle examination shall be performed on all pressure-boundary attachment welds.
SHELL-AND-TUBE HEAT EXCHANGERS
37
12.3.7 Magnetic-particle examination shall be performed on areas where temporary lugs have been removed.
These areas shall be prepared by grinding them before the examination. Liquid penetrant examination shall be
substituted for nonmagnetic materials.
12.3.8 After the hydrostatic test, a magnetic-particle examination shall be performed on all external
pressure-retaining welds and all internal nozzle welds that are accessible without disassembling the heat exchanger.
12.3.9 For components subject to full radiography, nozzle-attachment welds that cannot be radiographed shall be
examined for the presence of cracks by the magnetic-particle method or by the liquid-penetrant method. Examination
shall apply to the root pass after back-chipping or after flame-gouging, if applicable, and to the completed weld. Any
defects revealed shall be removed before the weld is finished. For liquid-penetrant examination of austenitic stainless
steel, neither the penetrant nor the developer shall contain any chlorides.
12.3.10 Full radiographic examination shall be performed on all pressure-retaining butt welds.
12.3.11 Ultrasonic examination shall be performed on all pressure-retaining butt welds for components over 50 mm
(2 in.) thick, after any postweld heat treatment. Ultrasonic examination shall comply with the pressure design code.
The entire volume of deposited weld metal shall be examined from two directions. Before the welds are examined, the
adjacent base material shall be examined by means of longitudinal beam with a 100 % scan for a distance of twice the
plate thickness back from the weld. A diagram shall be prepared indicating all areas larger than 12 mm (1/2 in.) in
diameter that show a loss of back-reflection of 50 % or more. The acceptance criteria shall be agreed by the
purchaser and the vendor.
Annex A
(informative)
Recommended Practices
A.1 Introduction
This annex has been prepared to give advice to the designer. The advice is offered for guidance only.
The descriptions and the numbers following are those of sections in the main body of this standard.
A.2 General
A.2.1 Cyclic Design—Guidance to 4.9
A.2.1.1 The following is guidance to assist in identifying a potential cyclic service application:
— 20 % variance in normal operating pressure, and/or;
— 20 % variance in process flow rate, and/or;
— variation in normal operating temperature that exceeds 110 °C (200 °F).
One cycle is where the variance occurs in a time frame of less than 24 h and the number of cycles exceeds 12 per
year.
NOTE
The variation in the normal operating temperature is suggested by API RP 571, Section 4.2.9.3 c), Thermal Fatigue.
A.2.1.2 For assistance in specifying cyclic conditions, it is suggested that the purchaser follow the guidance of
ASME BPVC, Section VIII, Division 2, and complete a User Design Specification. Methodologies are also available in
other pressure design codes, including EN 13445 (all parts).
A.2.1.3 The vendor can use the screening method provided in ASME BPVC, Section VIII, Division 2, to determine
whether a fatigue analysis is required for the given cyclic loading. If required, rules for performing a full fatigue
analysis are included. Methodologies are also available in other pressure design codes including EN 13445 (all
parts).
A.2.2 Sour or Wet Hydrogen Sulfide Service—Guidance to 4.10
A.2.2.1 NACE MR0103 establishes material requirements for resistance to sulfide stress cracking (SSC) in sour
petroleum refining and related process environments which contain hydrogen sulfide either as a gas or dissolved in
an aqueous (liquid-water) phase, with or without the presence of hydrocarbon. SSC is defined as cracking of a metal
under the combined action of tensile stress and corrosion in the presence of water and hydrogen sulfide. Other forms
of wet hydrogen sulfide cracking, environmental cracking, and severely corrosive and/or hydrogen charging
conditions that can lead to failures by mechanisms other than SSC are outside the scope of NACE MR0103.
A.2.2.2 Compared to the high pH environments of refinery sour service, oil and gas production sour environments
are covered by NACE MR0175 (all parts). This is because many wet sour streams in oil and gas production facilities
also contain carbon dioxide and hence exhibit a lower pH. In addition, chloride ion concentrations tend to be
significantly lower in refinery sour services than in oil and gas production sour services.
A.2.2.3 NACE MR0175 (all parts) provides requirements and recommendations for the selection and qualification of
metallic materials for service in equipment used in oil and gas production and natural gas processing plants in
38
SHELL-AND-TUBE HEAT EXCHANGERS
39
hydrogen sulfide containing environments. Mechanisms of cracking that can be caused by hydrogen sulfide include
sulfide stress cracking, stress corrosion cracking (SCC), hydrogen-induced cracking (HIC), step-wise cracking
(SWC), stress-oriented hydrogen-induced cracking (SOHIC), soft zone cracking (SZC), and galvanically induced
hydrogen stress cracking (GHSC).
A.2.2.4 Factors affecting the susceptibility of metallic materials to cracking in oil and gas production facilities in
hydrogen sulfide containing environments include the hydrogen sulfide partial pressure, in-situ pH, the concentration
of dissolved chlorides or other halides, the presence of elemental sulfur or other oxidants, temperature, galvanic
effects, mechanical stress and the duration of contact with a liquid water phase.
A.2.2.5 There are many process service environments which can expose carbon steel materials and weldments to
potentially damaging corrosion cracking mechanisms. For some of these environments (including HIC and SOHIC in
hydrogen sulfide and amine services) wet fluorescent magnetic-particle testing (WFMT) is the only inspection
technique that is considered to be highly effective in managing the material degradation risk during service (for
additional guidance see API 581).
A.2.2.6 In order to be able to apply the WFMT inspection technique, the inside wetted surface of welds must be
accessible to the technician after the heat exchanger has been fabricated. When the shell side fluid service is prone
to produce cracking in carbon steel, the following design guidelines can be applied to ensure that the wetted weld
surfaces will be accessible for WFMT inspection, both after the initial fabrication and post-weld heat treatment, as well
as for future in-service inspections.
— Fixed tubesheet heat exchangers should not be used.
— The minimum shell diameter should be DN 200 (8 NPS).
— For shells with nominal diameters between DN 200 (8 NPS) and DN 600 (24 NPS), the following should apply:
— rear shell covers should be the removable type;
— all nozzles should be located at the ends of the shell cylinder;
— the shell cylinder should be a single length of seamless pipe; rolled plate should only be used if there is
sufficient access to the internal surfaces of longitudinal and circumferential welds to allow them to be ground
flush.
— Shell side distributor belts should not be used.
— The minimum nozzle size should be DN 50 (2 NPS).
— Nozzles DN 150 (6 NPS) and smaller should be long weld neck type.
A.3 Outline Drawings and Other Supporting Data
A.3.1 Corrosion Allowance—Guidance to 6.1.1 j)
Corrosion allowance should be in accordance with TEMA if not otherwise specified by the purchaser. High alloy
materials are often specified with, or assumed to have, a zero corrosion allowance. For these materials, when
considering selection of component thickness, adding 0.4 mm (1/64 in.) above the pressure design code minimum
required thickness might be beneficial to assist fabrication and/or handling.
40
API STANDARD 660
A.3.2 Flow-induced Vibration—Guidance to 6.1.2
A.3.2.1 Background
The following guidance is to assist the designer in minimizing the risk of damage resulting from flow-induced vibration
in a shell-and-tube heat exchanger.
Tubes and the shell side fluid are susceptible to flow-induced vibrations from the unsteady pressures acting on the
surfaces of the tubes.
Tube vibration mechanisms in order of their increasing severity are turbulent buffeting, vortex shedding and fluidelastic instability. Excessive tube vibrations caused by turbulent buffeting or vortex shedding resonances can result in
thinning and eventual failure of tubes at the baffles or leaks at the tube-to-tubesheet joints. Fluid elastic instability
tends to have a run-away effect; once cross-flow velocities approach a critical velocity the tubes may vibrate
uncontrollably and can fail very rapidly.
The shell side may be subjected to acoustic resonances termed “acoustic vibrations.” Acoustic vibrations can vibrate
the shell and the exchanger’s foundations, but are more often associated with high levels of radiated sound.
The prediction and control of the vibration response of a shell-and-tube heat exchanger requires the characterization
of the system attributes and the excitation.
A.3.2.2 Characterization of the System Attributes
A.3.2.2.1 Tube Characteristics
The natural frequencies of a tube are functions of:
— the modulus of elasticity of the tube material;
— the moment of inertia of the tubular section;
— the number and length of spans;
— the effective tube mass, which includes the mass of the tube, the tube side fluid and a portion of the shell side
fluid.
The lowest natural frequency is termed the “fundamental frequency.” In general, higher order natural frequencies are
not integer multiples of the fundamental frequency.
In a heat exchanger, vibrational energy dissipation or damping is desirable, but not affected much by conventional
design choices. Dampening depends on the fluid density, viscosity, and surface tension, the vapor volume fraction,
the tube diameter, number and thickness of tube supports, the tube mass, and the fundamental natural frequency of
the tube.
A.3.2.2.2 Shell Side Fluid Volume Characteristics
The natural frequencies of the shell side gas volume are dictated by the speed of sound and the size of the
exchanger. The most offending mode is transverse to the longitudinal axes of the tubes and perpendicular to the
cross-flow. The wavelength of this mode is twice the shell diameter. As the diameter increases, the resonant
frequency of the transverse mode decreases, and opposite sides of the shell approach parallel planes. Both of these
effects increase the likelihood of a standing wave. Higher order diametral modes have natural frequencies that are
integer multiples of this fundamental frequency. The geometry of the shell also leads to a large number of higher order
cylindrical and longitudinal modes that can be problematic in rare circumstances. The speed of sound in a gas filled
SHELL-AND-TUBE HEAT EXCHANGERS
41
exchanger, assuming ideal behavior, is a function of the pressure, the ratio of specific heats, the density, and the
geometry of the tube bundle. Sound travels much faster in liquids compared to gases so resonant frequencies are
much higher and generally beyond the range of excitation. In two-phase flows, the speed of sound is somewhat
ambiguous, but clearly diminished relative to both the all-liquid and all-vapor values; fortunately, the abundance of
vapor-liquid interfaces provides acoustic damping.
A.3.2.2.3 Characterization of Excitation
When fluid flows over the tube surfaces, pressures oscillating at the boundary result in unsteady forces that lead to
turbulent buffeting. The frequency, content, and intensity of these pressure oscillations is a function of the velocity
magnitude and direction and the layout of the tubes. The intensity of the pressure oscillations on the tubes is
substantially greater for cross-flow compared to parallel flow.
In cross-flow, the principal excitation frequency is a function of the cross-flow velocity, tube diameter, and the
dimensionless Strouhal number. Measurements of Strouhal numbers are available for standard layout angles and
pitch ratios. In a nonlinear fluid-structure interaction phenomenon termed “lock-on,” the principal frequency of the
unsteady pressures on the tube surface will actually tune itself to the fundamental natural frequency of the tube. This
high amplitude, resonant response, is termed “vortex shedding” and is primarily a concern in isolated cylinders or
possibly tubes on the bundle perimeter. Potentially, the most destructive tube vibration mechanism and thus the
principal design concern is fluid-elastic instability. As the cross-flow velocity is increased, the excitation energy may
exceed dissipation so that excessive vibration amplitudes result in tube failures (see A.4.1).
Oscillating pressures in the wakes of the tubes can also excite an acoustic resonance of the shell side gas volume.
The lock-on phenomenon is possible if the excitation and resonant frequencies are close in value. In this case, the
principal frequency of the oscillating pressures can shift to a resonant acoustic frequency as well.
A.3.2.2.4 Vibration Evaluation
Evaluation of the vibration potential requires the determination of several important parameters: tube natural
frequencies, acoustic natural frequencies, turbulent buffeting frequency, vortex shedding frequency, acoustic vibration
frequency, and the ratio of excitation frequencies to natural frequencies along with the vibration amplitude. Excitation
frequencies within a range of ±20 % of the natural frequency have “lock-on” potential, and may lead to mechanical or
acoustical resonance. Additionally, the critical velocity, which is the threshold for fluid-elastic instability, and the crossflow velocities at both the mid-span and at the baffle tips are important parameters to understand. Vulnerable tubes
can include those at the bundle entrance and exit, at the baffle tips, in the window region (where tubes are supported
at every second baffle), and at the bundle perimeter.
It should be noted that vibration analysis is not an exact science and that allowances should be made for uncertainties
in some key parameters such as local shell side velocities.
A.3.2.3 Vibration Mitigation
A.3.2.3.1 Tube Vibration Mitigation
At the design stage, excessive tube vibrations can be dampened by shortening the span lengths that increase the
natural frequencies of the tubes. Intermediate supports in vulnerable areas like the inlet or the U-bend region can be
very effective and have minimal thermal hydraulic effect. The selection of the baffle type, e.g. NTIW (no tube in the
window) or rod supports, and adequate baffle spacing, can keep tube vibrations within acceptable limits.
For operating units, tube vibration problems can be addressed by stiffening the tubes with stakes, clips, or inserts of
various types. Removing vulnerable tubes, reducing shell side flow rate, and replacing the tube bundle are additional
mitigation techniques.
42
API STANDARD 660
A.3.2.3.2 Acoustic Vibration Mitigation
Deresonating baffles can successfully mitigate acoustic vibration problems by detuning the resonant frequency of the
gas volume with respect to the excitation frequencies. The baffles are positioned coplanar with the cross-flow and the
axes of the tubes. These baffles partition the shell volume into several smaller volumes of higher natural frequency,
provided the baffles have sufficient acoustic impedance (thickness and density). Since the diametral acoustic waves
stand across the diameter of the shell, full extension of the deresonating baffles wall-to-wall is unnecessary and can
lead to maldistribution. For higher order cylindrical and longitudinal mode resonances, deresonating baffles are also
effective since the shell loses its cylindrical symmetry. Multiple, asymmetrically spaced deresonating baffles can
mitigate the fundamental transverse diametral wave as several harmonics. However, a misplaced deresonating baffle
may tune the system and create a resonant condition.
A.3.3 Design Calculations—Guidance to 6.2.4
In calculating the effective heat transfer area, the purchaser and vendor should agree as to whether the “U” bend
region should be included.
A.4 Design
A.4.1 Tube Failure in High Pressure Units—Guidance to 7.5.1.1
The effects of potential overpressure on the low pressure side of the heat exchanger caused by tube rupture should
be considered.
In certain extreme circumstances, the large volume of vapor that will be released during a tube failure scenario may
lead to excessive size of the relief valve or rupture disk. An option in such a case is to consider using smaller diameter
tubes (e.g. 16 mm [5/8 in.]).
NOTE
For further information, see API 521.
A.4.2 Transverse Baffles and Support Plates—Guidance to 7.5.3
Segmental baffles are conventional in shell-and-tube heat exchangers, as described in 7.5.3. Alternate types of
baffled (or non-baffled) designs can be permitted if agreed with the purchaser.
A.4.3 Tube Bundle Skid Bars—Guidance to 7.5.6
A.4.3.1 For tube bundles with mass and dimensions outside the range of conventional bundle-pulling devices,
alternative means of bundle removal should be considered. For example, if the bundle mass exceeds 18,150 kg
(40,000 lb), the diameter exceeds 1220 mm (48 in.), or the length exceeds 7.3 m (24 ft), the following options can be
considered:
a) bundle rollers;
b) skid bars on a rail;
c) removable shell.
A.4.3.2 Skid bars should not obstruct tube lanes or pass-partition lanes if 45° or 90° tube layouts are used.
SHELL-AND-TUBE HEAT EXCHANGERS
43
A.4.4 Tube-to-Tubesheet Joint—Guidance to 7.5.7
A.4.4.1 If there is potential for crevice corrosion on the shell side, tubes should be expanded to within 3 mm (1/8 in.)
from the shell side face of the tubesheet.
A.4.4.2 Where work hardening of the tube material during rolling could result in the potential for environmental
cracking, a strength-welded tube-to-tubesheet joint should be applied, and a light expansion (1 % to 3 % wall
reduction) should be applied (as per A4.4.1) if crevice corrosion from the shell side fluid is a concern.
A.4.4.3 Strength-welded tube-to-tubesheet joints should be considered by the purchaser for the following
conditions.
a) If the design pressure on either side exceeds 7000 kPa (ga) (1000 psig).
b) If duplex stainless steel tubes are used in wet hydrogen sulfide service.
c) If titanium tubes are used (provided the wall thickness is adequate for strength welding).
d) Where austenitic stainless steel tubes and a ferritic steel tubesheet are used and the metal temperature is above
205 °C (400 °F).
e) For fixed tubesheet exchangers used in sulfur plant applications (e.g. waste heat exchangers, sulfur condensers,
reheaters, acid gas preheaters, etc.).
f) In heat transfer fluid services with operating temperatures exceeding 205 °C (400 °F).
g) In cyclic service.
h) In a service where sudden temperature excursions can occur.
i) When the fy ratio of tubesheet SMYS to tube SMYS, as defined in ASME BPVC, Section VIII Division 1, NonMandatory Appendix A, “Basis for Establishing Allowable Loads for Tube-to-Tubesheet Joints” is less than 0.6.
For clad tubesheets, the tubesheet yield stress used in the calculation of fy should be that of the base material.
A.4.4.4 Seal-welded or strength-welded tube-to-tubesheet joints should be considered by the purchaser for the
following conditions.
a) Where leakage from the high pressure side to the low pressure side is not acceptable for process reasons (e.g.
where contamination of the lower pressure side would be detrimental to the process or pose an unacceptable
hazard to utility systems such as steam/condensate or cooling water).
b) For exchangers handling steam or boiler feed-water at design conditions exceeding class 150 flange rating.
A.4.4.5 For heat exchangers in hydrogen service the tube-to-tubesheet joints should be strength-welded and
expanded when either of the following cases apply:
a) When the design pressure of the exchanger is 7000 kPa (ga) (1000 psig) or higher.
b) When the design temperature is in excess of 230 °C (450 °F).
A.4.4.6 Tube-to-tubesheet joints for tubesheets with clad or weld overlay on both sides of the tubesheet should be
strength-welded to the tube side cladding or weld overlay, and also expanded through the full thickness of the
tubesheet to within 3 mm (1/8 in.) of the shell side cladding or weld overlay. Where grooves are used, they should be
located in the base metal and not in the shell side cladding or weld overlay.
44
API STANDARD 660
A.4.4.7 If welded tube-to-tubesheet joints are specified for dissimilar tubes and tubesheet material, weld overlay or
cladding should be considered on the tubesheet to eliminate bimetallic welds. The overlay or cladding should have
the same metallurgy as the tubes.
A.4.5 Girth Flange Joint Supplementary Design Requirements—Guidance to 7.8
A.4.5.1 Since flanges that have been designed based on allowable stress limits alone may not be sufficiently rigid to
control leakage, additional flanged joint design verification in accordance with ASME PCC-1, Appendix O, as outlined
in section 7.8, is recommended whenever any of the following conditions apply:
a) hydrogen service;
b) maximum operating temperature greater than 186 °C (366 °F);
c) cyclic service;
d) sour or wet hydrogen sulfide service;
e) design pressure equal to or greater than 6900 kPa (ga) (1000 psig);
f) steam service, with operating pressures above 1035 kPa (ga) (150 psig);
g) shell diameter greater than 1200 mm (48 in.);
h) when specified by the purchaser.
A.4.5.2 By the very nature of their design, flanged joint assemblies in heat exchangers can result in operating
temperature gradients either around the circumference of a single girth flange, or as a temperature differential
between the two flanges that together make up the joint. The effects of these temperature gradients or differences on
the design and leak tightness of the flanged joint are not normally considered by conventional pressure vessel code
analysis, or by the additional flange analysis that is included in Section 7.8.
Large temperature gradients or differentials should be avoided whenever possible. When it is not possible to do so,
additional analysis of the flanged joint may be required in order to assure design adequacy and leak tightness.
Additional analysis should be considered when any of the following conditions might exist.
a) Flanged joints subject to rapid operating temperature changes.
b) Operating temperature differences between the inlet and outlet nozzles of multi-pass channels which exceed
110 °C (200 °F).
c) Tubesheet designs employing a gasket on each side of the tubesheet where the operating temperature
difference between the channel side and the shell side, at any location, exceed 110 °C (200 °F).
The method of analysis and additional requirements to be applied should be specified or agreed upon with the
purchaser.
A.4.5.3 In heat exchangers with stationary or fixed tubesheets and bolted flanges made of dissimilar materials, the
selection of solid stainless steel or high alloy tubesheets should be limited to applications where the maximum
diametral differential thermal expansion in each pair of tubesheet and flange does not exceed 2.5 mm (0.1 in.), unless
otherwise approved by the purchaser.
SHELL-AND-TUBE HEAT EXCHANGERS
45
A.4.6 Gaskets—Guidance to 7.10
Spiral-wound gaskets are not recommended for use in floating-head flanges as the centering rings may result in an
increase in the floating head flange diameter, and the shell diameter for pull-through (TEMA T-type) floating heads.
A.4.7 Requirements for Hydrogen Service—Guidance to 7.12
To prevent excessive relaxation of bolting and reduce potential for leaks, girth flanges should not be covered with
insulation. Note that the default 0.7 gasket relaxation fraction included in PCC-1 Appendix O may not be valid if
bolting is covered with insulation.
A.5 Materials
A.5.1 Gaskets—Guidance to 8.3
When using a gasket containing graphite, it should be considered that it is almost the noblest material in the table of
galvanic series. Some metals can be sacrificed when combined with graphite in certain environments. If graphite is to
be used in contact with the flange in a service where the fluid contains sulfur, chlorides, halogens, or similar
impurities, the purchaser should consider alternate filler or facing materials.
A.6 Fabrication
A.6.1 Shells—Guidance to 9.1
Openings and attachments (including pads and support pads) should clear weld seams by at least 50 mm (2 in.). If
this is not possible, the seam weld should be ground flush and radiographed for a distance of 100 mm (4 in.) on either
side of the opening or for the full length covered by an attachment plus 100 mm (4 in.) on either side prior to welding
the nozzle or attachment to the heat exchanger.
A.7 Pressure Testing—Guidance to 10.3
Helium leak testing should be applied for tube-to-tubesheet joints in hydrogen service with a design pressure greater
than 6900 kPa (g) (1000 psig).
A.8 Preparation for Shipment
A.8.1 Protection—Guidance to 11.1
A.8.1.1 If water residues cannot be tolerated, equipment should be dried by one of the following methods.
a) Blowing dry air or nitrogen, of relative humidity less than 15 % (usually dehumidified), through the heat exchanger
and monitoring the outlet air until the relative humidity falls below 30 %.
b) Evacuating the heat exchanger with a vacuum pump to an absolute pressure of between 0.4 kPa (0.06 psi) and
0.5 kPa (0.075 psi).
A.8.1.2
After draining and drying, internal surfaces can be protected against corrosion by the addition of a
desiccant (e.g. silica gel), by the addition of a volatile corrosion inhibitor, or by blanketing with an inert gas such as
nitrogen [typically at gauge pressures up to 100 kPa (15 psi)].
Annex B
(informative)
Shell-and-Tube Heat Exchanger Checklist
The checklist (Table B.1) is used to record the specific requirements the purchaser shall make in response to the
sections in this standard alongside which bullets () are used to indicate that more information is required or it is
necessary to make a decision.
Completion of the checklist is the responsibility of the purchaser.
Table B.1—Checklist for Shell-and-Tube Heat Exchangers
Section
Item
4.1
Pressure design code.
4.3
Applicable local regulations.
Requirement
State required code.
State local regulations.
Do the shell side fluid characteristics require special considerations? If yes,
provide detailed information.
Yes
No
Do the tube side fluid characteristics require special considerations? If yes,
provide detailed information.
Yes
No
Is cyclic service design required? If yes provide detailed information.
Yes
No
Is the unit subject to sour or wet hydrogen sulfide service on the shell side?
Yes
No
Is the unit subject to sour or wet hydrogen sulfide service on the tube side?
Yes
No
Is the shell side in hydrogen service?
Yes
No
Is the tube side in hydrogen service?
Yes
No
4.12
Is input data required to determine the need for an expansion joint?
Yes
No
6.1.2
Is vibration analysis to be submitted for review?
Yes
No
6.2.2
Copies required of applicable welding procedure specifications, procedure
qualifications and weld map.
For
review
For
record
Not
required
6.2.5
Copies required of mechanical design calculations for supports, lifting and
pulling devices.
For
review
For
record
Not
required
4.7
4.8
4.10
4.11
6.3
Specify the format and quantities for the listed final documents.
7.1.1
Specify the maximum design temperature and a minimum design metal
temperature (MDMT) for shell and tube side.
7.3.6
Specify if supports on the shell shall be analyzed for local stresses. If yes,
provide detailed information.
Yes
No
7.4.11
Specify if girth flanges, channel covers, and floating-head flanges shall be
provided with future machining allowance on the gasket contact seating
surfaces.
Yes
No
7.5.2.5
Specify if tubesheets shall be provided with future machining allowance on
the gasket contact seating surface.
Yes
No
7.5.7.3
When strength welds are applied, the degree of expansion and use of
grooves shall be specified or agreed.
46
SHELL-AND-TUBE HEAT EXCHANGERS
47
Table B.1—Checklist for Shell-and-Tube Heat Exchangers
Section
Item
7.6.1
Required flange design code.
7.6.2
Are nozzles to be welded to the connecting piping (by others)? If so, specify
which connections.
7.6.6
Requirement
State flange design code.
Yes
No
Specify insulation thickness: Shell.
Specify insulation thickness: Channel.
7.6.8
Are chemical cleaning connections required?
Yes
No
7.6.9
Are specific nozzle loads and moments specified?
Yes
No
7.6.10
If nozzle sizes are larger than those listed in Table 2, specify the moments
and forces.
7.7.1
Are studded-in bolts permitted for channel and shell external girth joints?
Yes
No
7.7.6
Specify if hydraulic bolt tensioning is required.
Yes
No
7.7.8
If a bolt-tightening device is used, specify any special requirements required
for adequate clearance.
7.7.15
Specify if future machining allowance on the girth flange gasket contact
seating surface shall be provided.
Yes
No
7.8.1
Specify if the joint component approach per ASME PCC-1, App. O shall be
applied to the girth flange design. If yes, shall they be applied to one or both
sides of the heat exchanger?
Yes
No
7.12.2
Specify if any supplemental requirements are required for low chrome steels
in high temperature or high pressure hydrogen service. If yes, provide
detailed information.
Yes
No
8.1.4
Specify required materials of construction, including bolting and gaskets.
8.2.3
Specify maximum allowable carbon equivalent and/or restrictions on other
residual elements and micro-alloying elements for carbon steel components
in sour or wet hydrogen sulfide service.
9.5.11
Specify if weld procedure qualifications for carbon steel in sour or wet
hydrogen sulfide service shall include a micro-hardness survey. If yes,
specify any additional restrictions on residual elements or micro-alloying
elements for the qualification coupon materials.
Yes
No
9.5.12
Specify if weld procedure qualifications for duplex stainless steel shall
include a micro-hardness survey. If yes, establish the acceptance criteria.
Yes
No
9.6.2
Is heat treatment required after bending for U-tubes for process reasons?
Yes
No
9.6.5
Is heat treatment of ferritic and martensitic stainless steels, stabilized
austenitic stainless steels, duplex stainless steels, copper, copper nickel, or
high nickel alloys (Ni > 30 %) U-tubes required after cold working?
Yes
No
9.6.8
Specify if heat treated portion of U-tubes shall be de-scaled.
Yes
No
9.6.10
Specify if postweld heat treatment of weld-overlaid channels and bonnets is
required.
Yes
No
Is postweld heat treatment required for process reasons on the shell side?
Yes
No
Is postweld heat treatment required for process reasons on the tube side?
Yes
No
9.6.12
48
API STANDARD 660
Table B.1—Checklist for Shell-and-Tube Heat Exchangers
Section
Item
Requirement
9.10.4
Is a groove required within the shell side tubesheet cladding?
Yes
No
10.1.16
Specify if carbon steel plate in sour or wet hydrogen sulfide service shall be
subjected to an ultrasonic lamination check.
Yes
No
10.2.2
Specify if tube-to-tubesheet joint integrity shall be tested after final expansion
of the tubes by a helium leak test.
Yes
No
10.2.7
Are there additional requirements for drying or preservation? If yes, provide
detailed information.
Yes
No
11.1.7
Are there requirements for surface preparation and protection? If yes,
provide detailed information.
Yes
No
11.1.10
Is inert gas purge and fill required?
Yes
No
Are the additional requirements specified in Section 12 required for the shell
side?
Yes
No
Are the additional requirements specified in Section 12 required for the tube
side?
Yes
No
12.1
Annex C
(informative)
Shell-and-Tube Heat Exchanger Datasheets 5
The following datasheets are provided to assist the designer, vendor, and purchaser to specify the data necessary for
the design of a shell-and-tube heat exchanger for petroleum, petrochemical and natural gas services.
Completion of the datasheet is a joint responsibility of the purchaser and vendor. The purchaser (owner or contractor)
is responsible for the process data, which define the purchaser’s explicit requirements.
After the exchanger has been fabricated, the vendor should complete the datasheets to make a permanent record
that accurately describes the equipment “as-built.”
Additional datasheets may be required to define the shell-and-tube heat exchanger and examples are included in
Figure C.1 and Figure C.2.
— Connection schedule (see page 2 of Figure C.1 and Figure C.2), materials of construction (see page 2 of
Figure C.1 and Figure C.2): gaskets (see page 2 of Figure C.1 and Figure C.2). These are used if the designer/
user requires such level of detail to define materials for individual components. These sections may not be
necessary if page one defines the information sufficiently.
— Additional information, remarks, sketches, etc. (see page 3 of Figure C.1 and Figure C.2). These are used for
additional remarks if sufficient space is not available on pages 1 or 2. These are also used for schematic
sketches to illustrate required features of the design and tube layouts, if necessary, to provide this information to
the manufacturer.
— Additional process information (see page 4 of Figure C.1 and Figure C.2). One or two pages can be necessary if
boiling and/or condensing fluids with ranges of physical properties occur.
— Additional process information for thermal expansion design conditions (see page 5 of Figure C.1 and Figure
C.2). This is required only for exchangers such as fixed tubesheet or single-pass floating-head type exchangers
where thermal expansion must be considered for the mechanical design. This optional page should be included if
operating information is supplied to the designer for determination of the metal temperatures necessary for
expansion joint reviews.
— Additional cyclic service design data (see page 6 of Figure C.1 and Figure C.2). This is required only for
exchangers where the unit is subject to cyclic service.
5
Users of this Annex should not rely exclusively on the information contained in this document. Sound business, scientific,
engineering, and safety judgment should be used in employing the information contained herein.
Where applicable, authorities having jurisdiction should be consulted.
49
50
API STANDARD 660
SHELL-AND-TUBE HEAT EXCHANGER
Company
P.O. No.:
Engineering contractor
DATA SHEET (SI UNITS)
Doc. No.:
1 Client:
Location:
2 Process unit:
Item No.:
3 Job No.:
Fabricator:
4 Service of unit:
Page 1 of
No. of units:
5 Size:
6 Effective surface per unit (plain/finned):
TEMA Type:
m²
Connected in:
Parallel
Effective surface per shell:
Shells/unit:
7 PERFORMANCE OF ONE UNIT
Series
m²
SHELL SIDE
Inlet
8
TUBE SIDE
Inlet
Outlet
Outlet
9 Fluid name:
10 Fluid quantity, total:
kg/h
11
Vapor (relative molecular mass):
kg/h
12
Liquid:
kg/h
13
Steam:
kg/h
14
Water:
kg/h
15
Non-condensable (relative molecular mass):
kg/h
16 Temperature:
/
/
°C
kg/m³
17 Density (vapor/liquid):
18 Viscosity (vapor/liquid):
mPa·s
19 Specific heat (vapor/liquid):
kJ/(kg·K)
20 Thermal conductivity (vapor/liquid):
W/(m·K)
21 Specific latent heat:
kJ/kg @ °C
22 Inlet pressure:
@
@
kPa (ga)
23 Velocity:
m/s
24 Pressure drop (allowable/calculated):
kPa
25 Fouling resistance:
/
/
m²·K/W
26 Average film coefficient:
W/(m²·K)
27 Heat exchanged:
kW
W/(m²·K)
28 Heat transfer rate:
29 ρV²:
Mean temperature difference (MTD):
Required:
kg/(m·s²)
Inlet nozzle:
Tube Side (Y/N) Shell Side (Y/N)
30 Hydrogen Service:
°C
corrected/weighted
Fouled:
Sour Service:
Clean:
Bundle entrance:
Tube Side (Y/N) Shell Side
(Y/N)
Bundle exit:
Cyclic Service: (Y/N)
31 CONSTRUCTION PER SHELL
32 Tube Number:
OD:
33 Tube Wall Thickness:
mm
34 Tube Pitch:
mm
35 Tube Length:
mm
NOZZLES – Number, Size and Rating
minimum wall/average wall
Tube layout:
m
Tube type:
plain/finned/other
36 Tube to tubesheet joint:
37 Shell diameter:
SHELL SIDE
TUBE SIDE
/
/
Inlet:
Outlet:
Intermediate:
mm
(ID/OD)
/
Vent:
38 Cross-baffle type:
Drain:
39 Baffle Spacing: c/c
mm
40 Baffle Cut:
No. of cross passes:
%
vertical/horizontal
Pressure relief:
Design pressure:
kPa (ga)
41 Tube support type:
Vacuum:
42 Longitudinal baffle seal type:
Design temp. (Max/MDMT):
°C
43 Bypass seal type:
44 Impingement protection:
Number of passes per shell:
Corrosion allowance:
mm
(Y/N)
Type:
kPa (abs)
45 MATERIALS OF CONSTRUCTION
46 Shell:
Tubes:
GASKETS
47 Shell cover:
Shell side:
48 Channel or bonnet:
Tube side:
49 Channel cover:
Floating head:
50 Floating head cover/bolts:
51 Tubesheet:
52 Baffles:
Spare Gaskets required:
Stationary:
Floating:
Cross:
Longitudinal:
Test ring required:
(Y/N)
Insulation - shell:
mm
53 Tube support material:
Insulation - channel:
mm
54 Expansion joint type:
Expansion joint material:
55 Pressure design code:
56 REMARKS:
Stamp:
Calculate MAWP:
(Y/N)
TEMA Class:
57
58
Rev. No.
Description
Date
Prepared by
Reviewed by
inlet/outlet
SHELL-AND-TUBE HEAT EXCHANGERS
Company
P.O. No.:
Doc. No.:
SHELL-AND-TUBE HEAT EXCHANGER
CONNECTIONS AND MATERIALS
DATA SHEET (SI UNITS)
1 Client:
Location:
2 Process unit:
Item No.:
3 Job No.:
Fabricator:
4 CONNECTION SCHEDULE (Optional)
Mark
Number
Size
required
5
Rating
51
Facing
Engineering contractor
Page 2 of
Description
6
7
8
9
10
11
12
13
14
15
16
Chemical Cleaning
17 MATERIALS OF CONSTRUCTION (Optional)
Corrosion allowance
18 Shell:
mm
19
Head:
mm
20
Pipe/stub ends:
mm
21
Nozzle necks:
mm
22
Nozzle flanges:
mm
23
Body flanges:
mm
24
Expansion joint:
mm
25
Support:
mm
26
Bolting (internal):
mm
27
Bolting (external):
mm
28
Nozzle reinforcement:
mm
29 Tubes:
30 Tubesheets:
mm
31 Bonnet/channel:
mm
32
Bonnet head(s):
mm
33
Channel cover(s):
mm
34
Body flanges:
mm
35
Pipe/stub ends:
mm
36
Bolting (internal):
mm
37
Bolting (external):
mm
38
Nozzle reinforcement:
mm
39
Nozzle necks:
mm
40
Nozzle flanges:
mm
41 Baffles, spacers, tie rods:
mm
42
43
44
45
46
47
48
GASKETS (Optional)
49
50 Shell side:
51
Thickness:
Y =
52 Tube side:
53
55
Rev. No.
m =
Pa
Thickness:
mm
Thickness:
Pa
Y=
Revision
MAWP (hot and corroded):
kPa (ga)
MAP (new and cold):
kPa (ga)
Hydrotest pressure:
m =
Pa
Y=
54 Floating head:
MECHANICAL DATA (Optional)
mm
mm
m =
Field:
Mass:
Date
kPa (ga)
Empty:
kg
Full of water:
kg
Prepared by
Shop:
kPa (ga)
Bundle:
Reviewed by
kg
52
API STANDARD 660
Company
P.O. No.:
Doc. No.:
SHELL-AND-TUBE HEAT EXCHANGER
ADDITIONAL INFORMATION
DATA SHEET (SI UNITS)
1 Client:
Location:
2 Process unit:
Item No.:
3 Job No.:
Engineering contractor
Page 3 of
Fabricator:
ADDITIONAL REMARKS, SKETCHES, ETC. (Optional)
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
Rev. No.
Revision
Date
Prepared by
Reviewed by
SHELL-AND-TUBE HEAT EXCHANGERS
53
SHELL-AND-TUBE HEAT EXCHANGER
ADDITIONAL PROCESS INFORMATION
DATA SHEET (SI UNITS)
Company
P.O. No.:
Engineering Contractor
Doc. No.:
Page 4 of
1
Client:
Location:
2
Process unit:
Item No.:
3
Job No.:
Fabricator:
4
5
6
7
Temp.
°C
Reference Pressure 1:
Enthalpy
kJ/kg
kPa (abs)
Vapor Mass
Fraction
1.001
0.9
0.800.8
0.7
0.600.6
0.5
0.400.4
0.3
0.200.2
0.1
0.000
1.00
1
1
0.80
Enthalpy (kJ/kg)
Enthalpy (Btu/lb)
1
0.60
1
0.40
0
0.20
0
0.00
0
Temperature
(°C)
Temperature
(°F)
Enthalpy
Enthalpy
Density
Vapor
kg/m³
Fluid Name:
Pressure
kPa (abs)
Density
Liquid
kg/m³
Viscoisty
Vapor
mPa·s
Viscoisty
Liquid
mPa·s
Temp.
°C
Reference Pressure 1:
Enthalpy
kJ/kg
Thermal
Cond. Vap.
W/m-°K
Thermal
Cond. Liq.
W/m-°K
Sp. Heat
Vapor
kJ/kg-°K
Surface
Tension
N/m
Liquid
Crit. Press.
kPa (abs)
Heat Release Curve
1
1.00
1
0.80
1
1
1.000.9
0.8
0.800.7
0.6
0.600.5
0.4
0.400.3
0.2
0.200.1
0
0.60
1
0
0.40
0
0.20
0
0.00
Rev. No.
Density
Liquid
kg/m³
Revision
Viscoisty
Vapor
mPa·s
Viscoisty
Liquid
mPa·s
Thermal
Cond. Vap.
W/m-°K
Date
Thermal
Cond. Liq.
W/m-°K
0.00
Temperature (°F)
Temperature (°C)
Enthalpy
Enthalpy
Density
Vapor
kg/m³
Liquid
Crit. Press.
°C
Heat Release Curve
kPa (abs)
Vapor Mass
Fraction
Sp. Heat
Liquid
kJ/kg-°K
Vapor Mass Fraction
Mass Vapor
Vapor
Mass
Fraction
Mass
Vapor
Fraction
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
Fluid Name:
Pressure
kPa (abs)
Enthalpy (kJ/kg)
Enthalpy (Btu/lb)
9
10
11
Fraction
MassVapor
VaporMass
Fraction
Heat Release Curve
Heat Release Curve
8
Sp. Heat
Vapor
kJ/kg-°K
Sp. Heat
Liquid
kJ/kg-°K
Prepared by
VaporMass
MassVapor
Fraction
Surface
Tension
N/m
Liquid
Crit. Press.
kPa (abs)
Reviewed by
Liquid
Crit. Press.
°C
54
API STANDARD 660
Company
P.O. No.:
Doc. No.:
SHELL-AND-TUBE HEAT EXCHANGER
ADDITIONAL PROCESS INFORMATION
DATA SHEET (SI UNITS)
1 Client:
Location:
2 Process unit:
Item No.:
3 Job No.:
Fabricator:
Engineering contractor
Page 5 of
4
5
6
DESIGN CONDITIONS FOR EXPANSION JOINT (Optional)
7
SHELL SIDE
8
9
Case
a
Flow
conditionb
Pressure
Outletc
°C
kPa (ga)
Inlet
°C
10
11
TUBE SIDE
Fluid temperature
d
Mean
metal
e
temp.
Number of
Flow
f
b
cycles
condition
Fluid temperature
Pressure
Outletc
°C
kPa (ga)
Inlet
°C
°C
d
Mean
metal
e
temp.
Number of
f
cycles
°C
12
13
14
15
16
17
18
19
20
21
Determine the mean shell and tube metal temperatures at the listed cases. Evaluate the need for an expansion joint based on the metal temperatures at
22 these conditions with either or both sides clean or with specified fouling.
23
Unless otherwise stated, operation in accordance with the recommendations of the TEMA Standards, paragraph E3.2, “Operating Procedures”, is assumed.
24
a
A case which may affect design (e.g. steam-out, upset, etc.).
25
b
F = flowing (specify flow rate), S= stagnant, E = empty.
26
c
Outlet temperature if known, thermal designer determines for other conditions.
27
d
Specify design pressure for operating conditions. Use maximum actual pressure at other conditions.
28
e
Mean metal temperature to be specified by thermal designer.
29
f
Number of cycles that will occur during life of the exchanger for each case.
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
Rev. No.
Revision
Date
Prepared by
Reviewed by
SHELL-AND-TUBE HEAT EXCHANGERS
SHELL-AND-TUBE HEAT EXCHANGER
CYCLIC SERVICE INFORMATION
DATA SHEET (SI UNITS)
Company
P.O. No.:
55
Engineering Contractor
Doc. No.:
Page 6 of
1
Client:
Location:
2
Process unit:
Item No.:
3
Job No.:
Fabricator:
4
5
6
Description of Cyclic Service Operation
7
8
9
10
Condition
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
Initial
Condition
Initial
Rev. No.
Time
(h/m)
Duration
(h/m)
Composition
Flow Rate
(kg/h)
0.0
Time
(h/m)
0.0
Duration
(h/m)
Temperature
Pressure
(°C)
kPa (ga)
NOTES:
Revision
Date
Prepared by
Reviewed by
56
API STANDARD 660
SHELL-AND-TUBE HEAT EXCHANGER
Company
Engineering contractor
DATA SHEET (US CUSTOMARY UNITS)
P.O. No.:
Doc. No.:
1 Client:
Location:
2 Process unit:
Item No.:
3 Job No.:
Fabricator:
4 Service of unit:
Page 1 of
No. of units:
5 Size:
6 Effective surface per unit (plain/finned):
TEMA Type:
ft²
Connected in:
Parallel
Effective surface per shell:
Shells/unit:
7 PERFORMANCE OF ONE UNIT
Series
ft²
SHELL SIDE
8
Inlet
9 Fluid name:
TUBE SIDE
Outlet
Inlet
Outlet
lb/h
10 Fluid quantity, total:
lb/h
11
Vapor (relative molecular mass):
lb/h
12
Liquid:
lb/h
13
Steam:
lb/h
14
Water:
lb/h
15
Non-condensable / relative molecular mass:
lb/h
16 Temperature:
/
/
°F
lb/ft³
17 Density (vapor/liquid):
18 Viscosity (vapor/liquid):
cP
19 Specific heat (vapor/liquid):
Btu/(lb·°F)
20 Thermal conductivity (vapor/liquid):
Btu/(h·ft·°F)
21 Specific latent heat:
Btu/lb @ °F
22 Inlet pressure:
@
@
psig
23 Velocity:
ft/s
24 Pressure drop (allowable/calculated):
/
psi
25 Fouling resistance:
/
h·ft²·°F/Btu
26 Average film coefficient:
Btu/(h·ft²·°F)
27 Heat exchanged:
Btu/h
28 Heat transfer rate:
29 ρV²:
30 Hydrogen Service:
Btu/(h·ft²·°F)
Mean temperature difference (MTD):
Required:
°F
corrected/weighted
Fouled:
Ib/(ft·s²)
Inlet nozzle:
Tube Side (Y/N) Shell Side (Y/N)
Sour Service:
Clean:
Bundle entrance:
Tube Side (Y/N) Shell Side
(Y/N)
Bundle exit:
Cyclic Service: (Y/N)
31 CONSTRUCTION PER SHELL
32 Tube Number:
OD:
NOZZLES – Number, Size and Rating
in
33 Tube Wall Thickness:
in
minimum wall/average wall
34 Tube Pitch:
in
Tube layout:
35 Tube Length:
ft
Tube type:
plain/finned/other
36 Tube to tubesheet joint:
37 Shell diameter:
SHELL SIDE
TUBE SIDE
/
/
Inlet:
Outlet:
Intermediate:
in
(ID/OD)
/
Vent:
38 Cross-baffle type:
Drain:
39 Baffle Spacing: c/c
in
No. of cross passes:
40 Baffle Cut:
%
vertical/horizontal
Pressure relief:
Design pressure:
psig
41 Tube support type:
Vacuum:
psia
42 Longitudinal baffle seal type:
Design temp. (Max/MDMT):
°F
43 Bypass seal type:
44 Impingement protection:
Number of passes per shell:
Corrosion allowance:
in
(Y/N)
Type:
45 MATERIALS OF CONSTRUCTION
46 Shell:
GASKETS
Tubes:
47 Shell cover:
Shell side:
48 Channel or bonnet:
Tube side:
49 Channel cover:
Floating head:
50 Floating head cover/bolts:
51 Tubesheet:
52 Baffles:
Spare Gaskets required:
Stationary:
Floating:
Cross:
Longitudinal:
Test ring required:
(Y/N)
Insulation - shell:
in
53 Tube support material:
Insulation - channel:
in
54 Expansion joint type:
Expansion joint material:
55 Pressure design code:
56 REMARKS:
Stamp:
Calculate MAWP:
(Y/N)
TEMA Class:
57
58
Rev. No.
Revision
Date
Prepared by
Reviewed by
inlet/outlet
SHELL-AND-TUBE HEAT EXCHANGERS
57
SHELL-AND-TUBE HEAT EXCHANGER
CONNECTIONS AND MATERIALS
DATA SHEET (US CUSTOMARY UNITS)
Company
P.O. No.:
Engineering contractor
Doc. No.:
Page 2 of
1 Client:
Location:
2 Process unit:
Item No.:
3 Job No.:
Fabricator:
4 CONNECTION SCHEDULE (Optional)
Mark
Number
Size
required
5
Rating
Facing
Description
6
7
8
9
10
11
12
13
14
Chemical cleaning
15
16 MATERIALS OF CONSTRUCTION (Optional)
Corrosion allowance
17 Density (vapor/liquid):
in
18 Viscosity (va Head:
in
19 Specific heat Pipe/stub ends:
in
20 Thermal condNozzle necks:
in
21
Nozzle flanges:
in
22
Body flanges:
in
23
Expansion joint:
in
24
Support:
in
25
Bolting (internal):
in
26
Bolting (external):
in
27
Nozzle reinforcement:
in
28 Tubes:
29 Tubesheets:
in
30 Bonnet/channel:
in
31
Bonnet head(s):
in
32
Channel cover(s):
in
33
Body flanges:
in
34
Pipe/stub ends:
in
35
Bolting (internal):
in
36
Bolting (external):
in
37
Nozzle reinforcement:
in
38
Nozzle necks:
in
39
Nozzle flanges:
in
40 Baffles, spacers, tie rods:
in
41
42
43
44
45
46
47
49 Shell side:
50
Thickness:
Y =
51 Tube side:
52
Rev. No.
in
m =
psi
Thickness:
in
Thickness:
psi
Y=
Revision
MAWP (hot and corroded):
psig
MAP (new and cold):
psig
Hydrotest pressure:
m =
psi
Y=
53 Floating head:
54
MECHANICAL DATA (Optional)
GASKETS (Optional)
48
in
Field:
Mass:
m =
Date
psig
Empty:
lb
Full of water:
lb
Prepared by
Shop:
psig
Bundle:
Reviewed by
lb
58
API STANDARD 660
SHELL-AND-TUBE HEAT EXCHANGER
ADDITIONAL INFORMATION
DATA SHEET (US CUSTOMARY UNITS)
Company
P.O. No.:
Engineering contractor
Doc. No.:
Page 3 of
1 Client:
Location:
2 Process unit:
Item No.:
3 Job No.:
Fabricator:
ADDITIONAL REMARKS, SKETCHES, ETC. (Optional)
4
5
6
7
8
9
10
11
Vapor (relative molecular mass):
12
13
14
15
16
17 Density (vapor/liquid):
18 Viscosity (vapor/liquid):
19 Specific heat (vapor/liquid):
20 Thermal conductivity (vapor/liquid):
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
Rev. No.
Revision
Date
Prepared by
Reviewed by
SHELL-AND-TUBE HEAT EXCHANGERS
59
SHELL-AND-TUBE HEAT EXCHANGER
ADDITIONAL PROCESS INFORMATION
DATA SHEET (US CUSTOMARY UNITS)
Company
P.O. No.:
Engineering Contractor
Doc. No.:
Page 4 of
1
Client:
Location:
2
Process unit:
Item No.:
3
Job No.:
Fabricator:
4
5
6
7
Heat Release Curve
8
Heat Release Curve
psia
Vapor Mass
Fraction
1
1.00
0.9
0.8
0.80
0.7
0.6
0.60
0.5
0.4
0.40
0.3
0.2
0.20
0.1
0
0.00
1
1.00
1
0.80
1
0.60
1
0.40
0
D
V
S
T
0.20
0
0
0.00
Fraction
MassVapor
VaporMass
Fraction
Reference Pressure 1:
Enthalpy
Btu/lb
Enthalpy (Btu/lb)
Enthalpy (Btu/lb)
Temperature(°F)
(°F)
Temperature
Enthalpy
Enthalpy
Density
Vapor
lb/ft3
Fluid Name:
Pressure
psia
Density
Liquid
lb/ft3
Viscoisty
Vapor
cP
Viscoisty
Liquid
cP
Temp.
°F
Reference Pressure 1:
Enthalpy
Btu/lb
Thermal
Cond. Vap.
Btu/h-ft-°F
Thermal
Cond. Liq.
Btu/h-ft-°F
Sp. Heat
Vapor
Btu/lb-°F
Surface
Tension
dyne/cm
Liquid
Crit. Press.
psia
Heat Release Curve
1.001
0.9
0.800.8
0.7
0.600.6
0.5
0.4
0.400.3
0.2
0.200.1
0
0.00
1
1.00
1
0.80
1
0.60
1
0.40
0
0
0.20
0
0.00
Temperature (°F)
Temperature (°F)
EnthalpyEnthalpy
Density
Vapor
lb/ft3
Rev. No.
Density
Liquid
3
lb/ft
Revision
Viscoisty
Vapor
cP
Viscoisty
Liquid
cP
Thermal
Cond. Vap.
Btu/h-ft-°F
Date
Liquid
Crit. Press.
°F
Heat Release Curve
psia
Vapor Mass
Fraction
Sp. Heat
Liquid
Btu/lb-°F
Vapor Mass Fraction
Mass Vapor
Vapor
Mass
Fraction
Mass
Vapor
Fraction
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
Fluid Name:
Pressure
Temp.
Vapor (relative m°F
Enthalpy (Btu/lb)
Enthalpy (Btu/lb)
9
10
11
Thermal
Cond. Liq.
Btu/h-ft-°F
Sp. Heat
Vapor
Btu/lb-°F
Sp. Heat
Liquid
Btu/lb-°F
Prepared by
Vapor Mass
Mass Fraction
Vapor
Surface
Tension
dyne/cm
Liquid
Crit. Press.
psia
Reviewed by
Liquid
Crit. Press.
°F
60
API STANDARD 660
SHELL-AND-TUBE HEAT EXCHANGER
EXPANSION JOINT INFORMATION
DATA SHEET (US CUSTOMARY UNITS)
Company
P.O. No.:
Engineering contractor
Doc. No.:
Page 5 of
1 Client:
Location:
2 Process unit:
Item No.:
3 Job No.:
Fabricator:
4
5
6
DESIGN CONDITIONS FOR EXPANSION JOINT (Optional)
7
SHELL SIDE
8
Flow
Fluid temperature
b
9
10
condition
Casea
Vapor
(relative
molecular
mass):
11
Pressured
TUBE SIDE
Mean
metal
Number of
e
Inlet
°F
Outletc
°F
temp.
psig
f
cycles
Flow
Fluid temperature
b
condition
Mean
metal
e
Inlet
°F
°F
Pressured
Outletc
°F
temp.
psig
Number of
cyclesf
°F
12
13
14
15
16
Density
(vapor/liq
uid):
17
Viscosity
(vapor/liq
uid):
18
Specific
heat
(vapor/liq
uid):
19
Thermal
conductiv
ity
(vapor/liq
uid):
20
21
Determine the mean shell and tube metal temperatures at the listed cases. Evaluate the need for an expansion joint based on the metal temperatures at
22 these conditions with either or both sides clean or with specified fouling.
23
Unless otherwise stated, operation in accordance with the recommendations of the TEMA Standards, paragraph E3.2, “Operating Procedures”, is assumed.
24
a
A case which may affect design (e.g. steam-out, upset, etc.).
25
b
F = flowing (specify flow rate), S= stagnant, E = empty.
26
c
Outlet temperature if known, thermal designer determines for other conditions.
27
d
Specify design pressure for operating conditions. Use maximum actual pressure at other conditions.
28
e
Mean metal temperature to be specified by thermal designer.
29
f
Number of cycles that will occur during life of the exchanger for each case.
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
Rev. No.
Revision
Date
Prepared by
Reviewed by
SHELL-AND-TUBE HEAT EXCHANGERS
61
SHELL-AND-TUBE HEAT EXCHANGER
CYCLIC SERVICE INFORMATION
DATA SHEET (US CUSTOMARY UNITS)
Company
P.O. No.:
Engineering Contractor
Doc. No.:
Page 6 of
1
Client:
Location:
2
Process unit:
Item No.:
3
Job No.:
Fabricator:
4
5
6
Description of Cyclic Service Operation
7
8
9
10
Condition
11
Vapor (relative m
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
Initial
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
Time
(h/m)
Duration
(h/m)
Composition
Flow Rate
(lb/h)
0.0
D
V
S
T
Condition
Initial
Rev. No.
Time
(h/m)
0.0
Duration
(h/m)
Temperature
Pressure
(°F)
(psig)
NOTES:
Revision
Date
Prepared by
Reviewed by
Bibliography
[1] ASME Boiler and Pressure Vessel Code (BPVC), Section VIII, Rules for Construction of Pressure Vessels
[2] ASME Boiler and Pressure Vessel Code (BPVC), Section VIII, Rules for Construction of Pressure Vessels,
Division 2, Alternative Rules
[3] EN 13445 (all parts) 6, Unfired pressure vessels
[4] ASME Boiler and Pressure Vessel Code (BPVC), Section II, Materials
[5] WRC BUL 537 7, Precision Equations and Enhanced Diagrams for Local Stresses in Spherical and Cylindrical
Shells Due to External Loadings for Implementation of WRC Bulletin 107
[6] ASME B16.11, Forged Fittings, Socket-Welding and Threaded
[7] ASME B1.20.1, Pipe Threads, General Purpose (Inch)
[8] API 521, Pressure-relieving and Depressuring Systems
[9] EN 10160, Ultrasonic testing of steel flat product of thickness equal or greater than 6 mm (reflection method)
[10] ASME Boiler and Pressure Vessel Code (BPVC), Section V: Nondestructive Examination
[11] ASME SA-578, Specification for Straight-Beam Ultrasonic Examination of Plain and Clad Steel Plates for
Special Applications
[12] API RP 934-A, Materials and Fabrication of 2 ¼ Cr – 1 Mo, 2 ¼ Cr – 1 Mo – ¼ V, 3 Cr – 1 Mo, and
3 Cr - 1 Mo – ¼ V Steel Heavy Wall Pressure Vessels for High-temperature, High-pressure Hydrogen Service
[13] API RP 934-C, Materials and Fabrication of 1 ¼ Cr – ½ Mo Steel Heavy Wall Pressure Vessels for
High-pressure Hydrogen Service Operating at or below 825 degrees F (441 degrees C)
[14] ASTM B359/B359M 8, Standard Specification for Copper and Copper-Alloy Seamless Condenser and Heat
Exchanger Tubes with Integral Fins
[15] ASME SB-395/395M, Specification for U-Bend Seamless Copper and Copper Alloy Heat Exchanger and
Condenser Tubes
[16] API TR 938-C, Use of Duplex Stainless Steels in the Oil Refining Industry (technical report)
[17] API RP 571, Damage Mechanisms Affecting Fixed Equipment in the Refining Industry
[18] API RP 581, Risk Based Inspection Technology
6
7
8
European Committee for Standardization (CEN-CENELEC), Avenue Marnix 17, B-1000, Brussels, Belgium, www.cen.eu.
The Welding Research Council, P.O. Box 201547, Shaker Heights, Ohio 44122, www.forengineers.org.
ASTM International, 100 Barr Harbor Drive, West Conshohocken, Pennsylvania 19428, www.astm.org.
62
--`,`,,`,,`,`,````````,```,,,``-`-`,,`,,`,`,,`---
Product No. C66009
Download