The IP Endpoint Company
SIP Loudspeaker Amplifier
(PoE)
Operations Guide
Part #011405
Document Part #931236H
for Firmware Version 11.6.4
CyberData Corporation
3 Justin Court
Monterey, CA 93940
(831) 373-2601
Operations Guide 931236H
Part # 011405
COPYRIGHT NOTICE:
© 2018, CyberData Corporation, ALL RIGHTS RESERVED.
This manual and related materials are the copyrighted property of CyberData Corporation. No part
of this manual or related materials may be reproduced or transmitted, in any form or by any means
(except for internal use by licensed customers), without prior express written permission of
CyberData Corporation. This manual, and the products, software, firmware, and/or hardware
described in this manual are the property of CyberData Corporation, provided under the terms of an
agreement between CyberData Corporation and recipient of this manual, and their use is subject to
that agreement and its terms.
DISCLAIMER: Except as expressly and specifically stated in a written agreement executed by
CyberData Corporation, CyberData Corporation makes no representation or warranty, express or
implied, including any warranty or merchantability or fitness for any purpose, with respect to this
manual or the products, software, firmware, and/or hardware described herein, and CyberData
Corporation assumes no liability for damages or claims resulting from any use of this manual or such
products, software, firmware, and/or hardware. CyberData Corporation reserves the right to make
changes, without notice, to this manual and to any such product, software, firmware, and/or
hardware.
OPEN SOURCE STATEMENT: Certain software components included in CyberData products are
subject to the GNU General Public License (GPL) and Lesser GNU General Public License (LGPL)
“open source” or “free software” licenses. Some of this Open Source Software may be owned by
third parties. Open Source Software is not subject to the terms and conditions of the CyberData
COPYRIGHT NOTICE or software licenses. Your right to copy, modify, and distribute any Open
Source Software is determined by the terms of the GPL, LGPL, or third party, according to who
licenses that software.
Software or firmware developed by CyberData that is unrelated to Open Source Software is
copyrighted by CyberData, subject to the terms of CyberData licenses, and may not be copied,
modified, reverse-engineered, or otherwise altered without explicit written permission from
CyberData Corporation.
TRADEMARK NOTICE: CyberData Corporation and the CyberData Corporation logos are
trademarks of CyberData Corporation. Other product names, trademarks, and service marks may
be the trademarks or registered trademarks of their respective owners.
Technical Support 

The IP Endpoint Company The fastest way to get technical support for your VoIP product is to
submit a VoIP Technical Support form at the following website:
http://support.cyberdata.net/

Phone: (831) 373-2601, Ext. 333
Email: support@cyberdata.net
Fax: (831) 373-4193
Company and product information is at www.cyberdata.net.
Operations Guide
931236H
CyberData Corporation
Revision Information
Revision 931236H, which corresponds to firmware version 11.6.4, was released on January 23,
2018, and has the following changes:
•
Updates Table 2-2, "Parts List" and Table A-1, "Wall Mounting Components (Part of the
Accessory Kit)" to update the following text:
(3) #8 Plastic Anchors
(3) #8 x 1-1/4" Pan Head Phillips Self-Tapping Screws
Browsers Supported
The following browsers have been tested against firmware version 6.5.0:
Operations Guide
•
Internet Explorer (version: 10)
•
Firefox (also called Mozilla Firefox) (version: 23.0.1 and 25.0)
•
Chrome (version: 29.0.1547.66 m)
•
Safari (version: 5.1.7)
931236H
CyberData Corporation
Pictorial Alert Icons
General Alert
This pictoral alert indicates a potentially hazardous situation. This alert will be
followed by a hazard level heading and more specific information about the
hazard.
GENERAL ALERT
Ground
This pictoral alert indicates the Earth grounding connection point.
Hazard Levels
Danger: Indicates an imminently hazardous situation which, if not avoided, will result in death or
serious injury. This is limited to the most extreme situations.
Warning: Indicates a potentially hazardous situation which, if not avoided, could result in death or
serious injury.
Caution: Indicates a potentially hazardous situation which, if not avoided, could result in minor or
moderate injury. It may also alert users against unsafe practices.
Notice: Indicates a statement of company policy (that is, a safety policy or protection of property).
•
Operations Guide
The safety guidelines for the equipment in this manual do not purport to address all the safety
issues of the equipment. It is the responsibility of the user to establish appropriate safety,
ergonomic, and health practices and determine the applicability of regulatory limitations prior to
use. Potential safety hazards are identified in this manual through the use of words Danger,
Warning, and Caution, the specific hazard type, and pictorial alert icons.
931236H
CyberData Corporation
Important Safety Instructions
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has
two blades with one wider than the other. A grounding type plug has two blades and a third
grounding prong. The wide blade or the third prong are provided for your safety. If the provided
plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has
been damaged in any way, such as power-supply cord or plug is damaged, liquid has been
spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or
moisture, does not operate normally, or has been dropped.
13. Prior to installation, consult local building and electrical code requirements.
14. WARNING: The SIP Loudspeaker Amplifier (PoE) enclosure is not rated for any AC
voltages!
Warning
Electrical Hazard: This product should be installed by a licensed electrician
according to all local electrical and building codes.
GENERAL ALERT
Warning
Electrical Hazard: To prevent injury, this apparatus must be securely attached to
the floor/wall in accordance with the installation instructions.
GENERAL ALERT
Warning
The PoE connector is intended for intra-building connections only and does not
route to the outside plant.
GENERAL ALERT
Operations Guide
931236H
CyberData Corporation
Abbreviations and Terms
Operations Guide
Abbreviation or Term
Definition
A-law
A standard companding algorithm, used in European digital
communications systems to optimize, i.e., modify, the dynamic range of an
analog signal for digitizing.
AVP
Audio Video Profile
Cat 5
TIA/EIA-568-B Category 5
DHCP
Dynamic Host Configuration Protocol
LAN
Local Area Network
LED
Light Emitting Diode
Mbps
Megabits per Second.
NTP
Network Time Protocol
PBX
Private Branch Exchange
PoE
Power over Ethernet (as per IEEE 802.3af standard)
RTFM
Reset Test Function Management
SIP
Session Initiated Protocol
u-law
A companding algorithm, primarily used in the digital telecommunication
UC
Unified Communications
VoIP
Voice over Internet Protocol
931236H
CyberData Corporation
Contents
i
Chapter 1 Product Overview
1
1.1 How to Identify This Product .....................................................................................................1
1.2 Typical System Installation .......................................................................................................2
1.3 Product Features ......................................................................................................................3
1.4 Supported Protocols .................................................................................................................4
1.5 Supported SIP Servers .............................................................................................................4
1.6 Specifications ...........................................................................................................................5
1.7 Typical Coverage ......................................................................................................................6
1.8 Typical Warehouse Paging Setup .............................................................................................6
1.9 Compliance ..............................................................................................................................7
1.9.1 CE Testing ......................................................................................................................7
1.9.2 FCC Statement ..............................................................................................................7
Chapter 2 Installing the SIP Loudspeaker Amplifier (PoE)
8
2.1 Parts List ..................................................................................................................................8
2.2 SIP Loudspeaker Amplifier (PoE) Setup ...................................................................................9
2.2.1 SIP Loudspeaker Amplifier (PoE) Components ...........................................................10
2.2.2 NEMA Box Components of the SIP Loudspeaker Amplifier (PoE) ...............................11
2.2.3 Connecting the SIP Loudspeaker Amplifier (PoE) .......................................................12
2.2.4 SIP Loudspeaker Amplifier (PoE) System Installation and Connection Options ..........15
2.2.5 Strobe Connections Behind the Port Cover .................................................................17
2.2.6 Connecting the Strobe .................................................................................................18
2.2.7 SIP Loudspeaker Amplifier (PoE) Jumpers ..................................................................20
2.2.8 Ethernet Connection ....................................................................................................20
2.2.9 Loudspeaker Type ........................................................................................................21
2.2.10 Cabling/Wiring ............................................................................................................21
2.2.11 Confirm Operation ......................................................................................................22
2.2.12 Confirm the IP Address and Test the Audio ...............................................................23
2.2.13 Adjust the Volume ......................................................................................................24
2.3.1 Factory Default Settings ...............................................................................................27
2.3.2 SIP Loudspeaker Amplifier (PoE) Web Page Navigation .............................................28
2.3.3 Using the Toggle Help Button .......................................................................................29
2.3.4 Using the Toggle Help Button .......................................................................................31
2.3.5 Log in to the Home Page ..............................................................................................33
2.3.6 Configure the Device ....................................................................................................37
2.3.7 Configure the Network Parameters .............................................................................44
2.3.8 Configure the SIP (Session Initiation Protocol) Parameters .........................................47
2.3.9 Configure the Multicast Parameters .............................................................................56
2.3.10 Configure the Sensor Page Parameters .....................................................................60
2.3.11 Configure the Audiofiles Page Parameters .................................................................64
2.3.12 Configure the Events Parameters ..............................................................................71
2.3.13 Configure the Autoprovisioning Parameters ...............................................................77
2.4.1 Downloading the Firmware ...........................................................................................89
2.4.2 Reboot the Device ........................................................................................................91
2.5.1 Command Interface Post Commands ..........................................................................92
Appendix A Mounting the Amplifier
96
A.1 Mount the Amplifier ...............................................................................................................96
Appendix B Setting up a TFTP Server
98
B.1 Set up a TFTP Server ............................................................................................................98
B.1.1 In a LINUX Environment ..............................................................................................98
B.1.2 In a Windows Environment .........................................................................................98
Appendix C Troubleshooting/Technical Support
99
C.1 Frequently Asked Questions (FAQ) ........................................................................................99
C.2 Documentation .......................................................................................................................99
C.3 Contact Information ..............................................................................................................100
C.4 Warranty and RMA Information ............................................................................................100
Operations Guide
931236H
CyberData Corporation
ii
Index
Operations Guide
101
931236H
CyberData Corporation
1
1 Product Overview
1.1 How to Identify This Product
To identify the SIP Loudspeaker Amplifier (PoE), look for a model number label similar to the one
shown in Figure 1-1. Confirm the following:
•
The model number on the label should be 011405.
Figure 1-1. Model Number Label
www.cyberdata.net
SIP Loudspeaker Amplifier
011405A / 021111H
405000001
CAN ICES-3 (A)/NMB-3(A)
00:20:F7:03:83:CA
V 11.6.4
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 
(1) this device may not cause harmful interference, and (2) this device must accept any interference received, 
including interference that may cause undesired operation.
Model number
Operations Guide
Serial number begins with 405
931236H
CyberData Corporation
Product Overview 2
Typical System Installation
1.2 Typical System Installation
Figure 1-2 illustrates how the SIP Loudspeaker Amplifier (PoE) is normally installed as part of a
public address system.
Figure 1-2. Typical Installation
Compliant Non-PoE Ethernet Switch
SIP Server
Loudspeaker Amplifier
Operations Guide
VoIP Phone
931236H
CyberData Corporation
Product Overview 3
Product Features
1.3 Product Features
Operations Guide
•
SIP-enhanced interoperability for hosted environments
•
Support for security code access for SIP paging
•
Page to Polycom phones
•
Autoprovisioning via HTTPS
•
HTTPS web based configuration
•
Support for G.722 codecs
•
802.11q VLAN tagging
•
Configurable sense input for use with fault detection
•
Configurable event generation for device health and status monitoring
•
Optional direct connect RGB strobe kit connection
•
9 user-uploadable page messages
•
Features
•
Packaged in a NEMA 3/3x (IP55)-rated enclosure
•
Dual-speed ethernet 10/100 Mbps
•
Web-based configuration
•
PoE 802.3at and 802.3af-enabled Line-in for background music
•
Line-out connector
•
DTMF controlled relay
•
Direct 8 Ohm speaker drive
•
User-uploadable tones and messages
•
Digital and manual volume control
•
Second SIP endpoint "Night Ringer"
•
Autoprovisioning
•
Auto-call voice message from input port sense Can support two horns
•
HTTP Command Interface
•
10 channel prioritized Multicast ports
•
Built-in diagnostics
•
Delayed page support
•
Cisco SRST
931236H
CyberData Corporation
Product Overview 4
Supported Protocols
1.4 Supported Protocols
The SIP Loudspeaker Amplifier (PoE) supports:
•
SIP
•
Multicast
•
HTTP and HTTPS web-based configuration
Provides an intuitive user interface for easy system configuration and verification of SIP
Loudspeaker Amplifier (PoE) operations.
•
DHCP Client
Dynamically assigns IP addresses in addition to the option to use static addressing.
•
TFTP Client
Facilitates hosting for the configuration file for Autoprovisioning.
•
RTP
•
RTP/AVP - Audio Video Profile
•
SPEEX
•
Audio Encodings
PCMU (G.711 mu-law)
PCMA (G.711 A-law)
G.722
Packet Time 20 ms
1.5 Supported SIP Servers
The following link contains information on how to configure the SIP Loudspeaker Amplifier (PoE) for
the supported SIP servers:
http://www.cyberdata.net/connecting-to-ip-pbx-servers/
Operations Guide
931236H
CyberData Corporation
Product Overview 5
Specifications
1.6 Specifications
Table 1-1. Specifications
Specifications
Ethernet I/F
10/100 Mbps
Protocol
SIP RFC 3261 Compatible
Power Input
PoE 802.3at or 802.3af
Audio Output
802.3af - SPL 114 dB @ 1 metera
802.3at - SPL 117 dB @ 1 metera
Line In:
Input Signal Amplitudes
2.0 VPP maximum
Input Impedance
10k Ohm
Line Out:
Output Signal Amplitudes
2.0 VPP maximum
Output Level
+2dBm nominal
Total Harmonic Distortion
0.5% maximum
Output Impedance
10k Ohm
Operating Range
Temperature: -40o C to 55o C (-40o F to 131o F)
(with NEMA enclosure)
Humidity: 5-95%, non-condensing
Enclosure: NEMA3/3X (IP55 rated)
Storage Temperature
-40o C to 70o C (-40o F to 158o F)
Storage Altitude
Up to 15,000 ft. (4573 m)
Payload Types
G.711 a-law, G.711 u-law, and G.722
Dimensionsb
10 in. [254 mm] Length
4 in. [101.6 mm] Width
14 in. [355.6 mm] Height
Boxed Weight
6.5 lbs. [2.95 kg]
Compliance
CE; EMC Directive – Class A EN 55032 & EN 55024, LV
Safety Directive – EN 60950-1, RoHS Compliant, FCC; Part
15 Class A, Industry Canada; ICES-3 Class A, IEEE 802.3
Compliant
Part Number
011405
Loudspeaker Part Number
011068
a.When used with the 011068 Mini Horn.
b. Dimensions are measured from the perspective of the product being upright with the front of the
product facing you.
Operations Guide
931236H
CyberData Corporation
Product Overview 6
Typical Coverage
1.7 Typical Coverage
With one horn attached to Paging Amplifier under standard 802.3af PoE power, coverage is up to
5,000 square feet. With two horns attached to the Paging Amplifier under 802.3at PoE (high power),
coverage is up to 10,000 square feet depending on ambient background noise levels.
1.8 Typical Warehouse Paging Setup
Figure 1-3. Typical Warehouse Paging Setup
Loud Speaker Amplifier
Part Numbers: 011404 and 011405
"High Power Mode" with
Two (2) Horn Speakers Attached
Horn Speaker
Horn Speaker
Horn Speaker
Horn to Loud Speaker Amplifier
25'
25'
Horn Speaker
Loud Speaker Amplifier
Horn Speaker
Horn Speaker to Horn Speaker
50'
Horn Speaker
Office
Bathroom
Typical Example of a 70,000 Square Feet Warehouse Paging Set up
Operations Guide
931236H
CyberData Corporation
Product Overview 7
Compliance
1.9 Compliance
1.9.1 CE Testing
CE testing has been performed according to EN ISO/IEC 17050 for Emissions, Immunity, and Safety.
Note
You can download the Declaration of Conformity document from the Downloads tab of the
product’s webpage.
1.9.2 FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case
the user will be required to correct the interference at his own expense.
Operations Guide
931236H
CyberData Corporation
8
2 Installing the SIP Loudspeaker Amplifier
(PoE)
2.1 Parts List
Table 2-2 illustrates the parts for each SIP Loudspeaker Amplifier (PoE) and includes a kit for
mounting.
Table 2-2. Parts List
Quantity
Part Name
1
SIP Loudspeaker Amplifier (PoE) Assembly
1
Enclosure
1
Installation Quick Reference Guide
1
Mounting Accessory Kit which includes:
Illustration
(3) #8 Plastic Anchors
(3) #8 x 1-1/4" Pan Head Phillips Self-Tapping Screws
151147
#8x1.25" Truss Head Phillips
Sheet Metal Screw (3x)
531032
Plastic Ribbed Anchor (3x)
Operations Guide
931236H
CyberData Corporation
Installing the SIP Loudspeaker Amplifier (PoE) 9
SIP Loudspeaker Amplifier (PoE) Setup
2.2 SIP Loudspeaker Amplifier (PoE) Setup
Set up and configure each SIP Loudspeaker Amplifier (PoE) before you mount it.
CyberData delivers each SIP Loudspeaker Amplifier (PoE) with the factory default values indicated
in
Table 2-3:
Table 2-3. Factory Default Settings—Default of Network
Parameter
Factory Default Setting
IP Addressing
DHCP
IP
Addressa
10.10.10.10
Web Access Username
admin
Web Access Password
admin
Subnet Mask
a
255.0.0.0
a
10.0.0.1
Default Gateway
a. Default if there is not a DHCP server present.
Operations Guide
931236H
CyberData Corporation
Installing the SIP Loudspeaker Amplifier (PoE) 10
SIP Loudspeaker Amplifier (PoE) Setup
2.2.1 SIP Loudspeaker Amplifier (PoE) Components
Figure 2-4 shows the components of the SIP Loudspeaker Amplifier (PoE).
Figure 2-4. SIP Loudspeaker Amplifier (PoE) Components
RTFM Switch
VoIP
Loudspeaker
RTFM
To broadcast the device’s current IP address, use a bent
paperclip or a similar object to press and hold the RTFM switch
(located behind the hole) for a couple of seconds and then
release it.
To restore the factory defaults, complete the following steps:
1. Use a bent paperclip or a similar object to press and hold the
RTFM switch until you hear the device announce the words,
“restoring defaults” and “rebooting”.
2. Release the RTFM switch. The device will be restored to the
factory default settings.
Speaker Volume
Volume
SPD Link/Act.
Speed (SPD) LED (AMBER)
The Speed (SPD) LED illuminates AMBER for a 100Mb link 
or is off for 10MB when the network link to the device is 
established.
Link/Activity (Link/Act.) LED (GREEN) 
The GREEN Link/Activity (Link/Act.) LED blinks to indicate
network traffic.
PWR Status
Status LED (GREEN)
After supplying power to the device, a steady GREEN Status LED
illuminates. After about 20 seconds, the GREEN Status LED will
blink fast to indicate that the device is acquiring an IP address and
attempting to autoprovision. The GREEN Status LED will turn off
thereafter until the device has finished booting. When the device
has fully booted, the GREEN Status LED will turn on solid to
confirm the device is operational.
The GREEN Status LED will blink during a page when it is online.
Power (PWR) LED (GREEN/BLUE)
The Power (PWR) LED is GREEN in low power mode (802.3af)
and BLUE during high power mode (802.3at).
The IP Endpoint Company
Operations Guide
931236H
CyberData Corporation
Installing the SIP Loudspeaker Amplifier (PoE) 11
SIP Loudspeaker Amplifier (PoE) Setup
2.2.2 NEMA Box Components of the SIP Loudspeaker Amplifier (PoE)
Figure 2-5 shows all of the NEMA box components of the SIP Loudspeaker Amplifier (PoE).
Figure 2-5. Loudspeaker Amplifier Components—PoE
RTFM Switch
Ethernet Connection
Speaker Connection
LEDs
Volume
Operations Guide
931236H
CyberData Corporation
Installing the SIP Loudspeaker Amplifier (PoE) 12
SIP Loudspeaker Amplifier (PoE) Setup
2.2.3 Connecting the SIP Loudspeaker Amplifier (PoE)
2.2.3.1 Using the Amplified Outputs
Low Power Mode The following figure illustrate how to connect the SIP Loudspeaker Amplifier (PoE) and use the
(One Speaker)
amplified outputs in low power mode to one speaker or horn.
Figure 2-6. Using the Amplified Outputs—Low Power Mode with One Speaker
*Note: Horn is connected to terminal
block pins 9 (-) and 12 (+) of the
paging amplifier for mono mode.
CLASS II WIRING
802.3af PoE Ethernet Switch
or
Cat 5 Ethernet Cable
Mono(+)/Left Spkr (+) - 12
Left Spkr (-) - 11
Right Spkr (+) - 10
Mono(-)/Right Spkr (-) - 9
Line-Out (+) - 8
Line-Out (-) - 7
Line-In (-) - 6
Line-In (+) - 5
Relay COM - 4
Relay NO/NC - 3
Door Sense/Button Common (GND) - 2
Door Sense/Button Contact (+) - 1
+
Note: You can use an
802.3af compliance
switch or an 802.3af
power injector and hub.
*+
802.3af PoE Injector (low power mode)
*Note: The positive (+) wire coming from the speaker
may be red or white. The negative (-) wire is black.
*Note: Maximum recommended
length of the horn should be 50
feet from the amplifier.
Standard 1 Speaker Configuration
(802.3af mode)
8 Ohms
*Note: Use 16 gauge wire
coming out of screw terminals.
16 gauge wire
Twist wire nuts
+
Note: Use wire nuts to connect wire
from the speakers to 16 gauge wire.
Operations Guide
931236H
CyberData Corporation
Installing the SIP Loudspeaker Amplifier (PoE) 13
SIP Loudspeaker Amplifier (PoE) Setup
High Power Mode The following figure illustrate how to connect the SIP Loudspeaker Amplifier (PoE) and use the
(One Speaker)
amplified outputs in high power mode to one speaker or horn.
Figure 2-7. Using the Amplified Outputs—High Power Mode with One Speaker
*Note: Horn is connected to terminal
block pins 9 (-) and 12 (+) of the
paging amplifier for mono mode.
Note: You can use an
802.3at compliance
switch or an 802.3at
power injector and hub.
+
or
802.3at PoE Injector
(high power mode)
Mono(+)/Left Spkr (+) - 12
Left Spkr (-) - 11
Right Spkr (+) - 10
Mono(-)/Right Spkr (-) - 9
Line-Out (+) - 8
Line-Out (-) - 7
Line-In (-) - 6
Line-In (+) - 5
Relay COM - 4
Relay NO/NC - 3
Door Sense/Button Common (GND) - 2
Door Sense/Button Contact (+) - 1
CLASS II WIRING
802.3at PoE Ethernet Switch
*+
Cat 5 Ethernet Cable
*Note: The positive (+) wire coming from the speaker
may be red or white. The negative (-) wire is black.
*Note: Maximum recommended
length of the horn should be 50
feet from the amplifier.
Standard 1 Speaker Configuration
(802.3at mode)
8 Ohms
*Note: Use 16 gauge wire
coming out of screw terminals.
16 gauge wire
Twist wire nuts
+
Note: Use wire nuts to connect wire
from the speakers to 16 gauge wire.
Operations Guide
931236H
CyberData Corporation
Installing the SIP Loudspeaker Amplifier (PoE) 14
SIP Loudspeaker Amplifier (PoE) Setup
High Power Mode The following figure illustrate how to connect the SIP Loudspeaker Amplifier (PoE) and use the
(Two Speakers)
amplified outputs in high power mode to two speakers or horns.
Figure 2-8. Using the Amplified Outputs—High Power Mode with Two Speakers
*Note: Horn is connected to terminal
block pins 9 (-) and 12 (+) of the
paging amplifier for mono mode.
CLASS II WIRING
802.3at PoE Ethernet Switch
or
802.3at PoE Injector
(high power mode)
Mono(+)/Left Spkr (+) - 12
Left Spkr (-) - 11
Right Spkr (+) - 10
Mono(-)/Right Spkr (-) - 9
Line-Out (+) - 8
Line-Out (-) - 7
Line-In (-) - 6
Line-In (+) - 5
Relay COM - 4
Relay NO/NC - 3
Door Sense/Button Common (GND) - 2
Door Sense/Button Contact (+) - 1
+
Note: You can use an
802.3at compliance
switch or an 802.3at
power injector and hub.
Cat 5 Ethernet Cable
*Note: The positive (+) wire coming from the speaker
may be red or white. The negative (-) wire is black.
*+
Use 16 gauge wire coming out of screw terminals.
Note: Make sure that the wire length going to the
wire nuts is kept short (approximately 6 inches).
Optional 2 Speaker Configuration
(802.3at mode)
8 Ohms
*Note: Maximum recommended
length of each horn should be 25
feet from the amplifier.
Standard 1 Speaker Configuration
(802.3at mode)
8 Ohms
16 gauge wire
+
+
Twist wire nuts
2 speakers in parallel (4 Ohm total)
Note: Use wire nuts to connect wire
from the speakers to 16 gauge wire.
Operations Guide
931236H
CyberData Corporation
Installing the SIP Loudspeaker Amplifier (PoE) 15
SIP Loudspeaker Amplifier (PoE) Setup
2.2.4 SIP Loudspeaker Amplifier (PoE) System Installation and Connection
Options
The following figures show the connection options for the SIP Loudspeaker Amplifier (PoE).
Figure 2-9. SIP Loudspeaker Amplifier (PoE) Connections
CLASS II WIRING
Mono(+)/Left Spkr (+) - 12
Left Spkr (-) - 11
Right Spkr (+) - 10
Mono(-)/Right Spkr (-) - 9
Line-Out (+) - 8
Line-Out (-) - 7
Line-In (-) - 6
Line-In (+) - 5
Relay COM - 4
Relay NO/NC - 3
Door Sense/Button Common (GND) - 2
Door Sense/Button Contact (+) - 1
Speaker Connections
(Figure 2-6) (Figure 2-7)(Figure 2-8)
Line-Out Connection (10K Ohm)
Line-In Connection (Figure 2-10)
Relay Connection (Figure 2-11)
Sensor Connection (Figure 2-12)
Figure 2-10. Line-In Connection
When line-in is enabled on
the device, the audio
received from the line-in
connection will be played
to the speaker(s) and lineout connection as the lowest priority audio.
Loudspeaker Amplifier
Music Source
Operations Guide
931236H
CyberData Corporation
Installing the SIP Loudspeaker Amplifier (PoE) 16
SIP Loudspeaker Amplifier (PoE) Setup
Figure 2-11. Relay or LED Strobe Connection
When the device is called from a
remote phone, the relay on the
device can be programmed to blink
and drive an LED Strobe Light.
External device
such as an
electric door strike
or an LED Strobe
Light
AC or DC
Power
Source
High PIV Ultrafast
Switching Diode
Solid State or 
Mechanical Relay
OUT
IN
Output Contacts
AC or DC-rated
depending upon
controlled device
requirements
DC Power Supply
(Max. 30 VDC @ 1A)
Figure 2-12. Sensor Connection
Operations Guide
931236H
CyberData Corporation
Installing the SIP Loudspeaker Amplifier (PoE) 17
SIP Loudspeaker Amplifier (PoE) Setup
2.2.5 Strobe Connections Behind the Port Cover
See Figure 2-13 for the additional connection options for the SIP Loudspeaker Amplifier (PoE).
Figure 2-13. Connections Behind the Port Cover
CLASS II WIRING
MIC IN
3
2
1
STROBE
5
4
3
2
1
See Table 2-4 for the descriptions of the connections behind the port cover.
Table 2-4. Connections Behind the Port Cover
Microphone Connections
Name
MIC IN
Connection
Description
J6-1
Microphone chassis ground connections
J6-2
Microphone positive input
J6-3
Microphone negative input
Connection
Description
J9-1
Ground
J9-2
Strobe positive power (+24V)
J9-3
Ground
J9-4
I2C data
J9-5
I2C clock
Strobe Connections
Name
STROBE
Operations Guide
931236H
CyberData Corporation
Installing the SIP Loudspeaker Amplifier (PoE) 18
SIP Loudspeaker Amplifier (PoE) Setup
2.2.6 Connecting the Strobe
1. Insert the network cable through any available rubber grommet at the bottom of the enclosure.
See Figure 2-14.
2. Connect the Network Cable to the Paging Amplifier. See Figure 2-14.
Figure 2-14. Connecting the Strobe
then Connect Network Cable in to Paging Amplifier.
Rubber Grommets
Network Cable
Plugged in to
Network Port
Network Cable
Note:
Network Cable is Not Included.
Operations Guide
931236H
CyberData Corporation
Installing the SIP Loudspeaker Amplifier (PoE) 19
SIP Loudspeaker Amplifier (PoE) Setup
3. Remove the mounting screw to remove the cover plate. See Figure 2-15.
4. Remove the hole plug and grommet. See Figure 2-15.
5. Slide the cover plate through the slot on the cable grommet. See Figure 2-15.
6. Install the mounting screw to secure the cover plate. See Figure 2-15.
Figure 2-15. Connecting the Strobe
Strobe Cable Kit
(Part of RGB Strobe)
Back Plate
Mounting Screw
Cable
Grommet
Hole Plug &
Grommet
Mounting
Screw
Slot
Slot
J1
to STROBE
Cover Plate
011288 Auxiliary
RGB Strobe Kit
RGB Strobe
STROBE
MIC IN
Operations Guide
931236H
CyberData Corporation
Installing the SIP Loudspeaker Amplifier (PoE) 20
SIP Loudspeaker Amplifier (PoE) Setup
2.2.7 SIP Loudspeaker Amplifier (PoE) Jumpers
See Figure 2-16 for the jumper locations.
Figure 2-16. Jumper Locations
JP4
JP2
JP3
JP5
JP1
See Table 2-5 for the jumper descriptions.
Table 2-5. Jumper Descriptions
Jumper
Description
JP1
Reset—Factory Only
JP2
RTFM (not installed)
JP3
Audio Enable Jumper—Factory Only
JP4
Relay NO/NC (default to NO)—Factory Only
JP5
PoE IEEE 802.3at—Factory Only
2.2.8 Ethernet Connection
See Table 2-6 for details about the SIP Loudspeaker Amplifier (PoE) connection.
Table 2-6. SIP Loudspeaker Amplifier (PoE) Connection
Operations Guide
Connection
Connection Details
Location
Ethernet
Use a RJ 45 cable.
SIP Loudspeaker Amplifier
(PoE)
931236H
CyberData Corporation
Installing the SIP Loudspeaker Amplifier (PoE) 21
SIP Loudspeaker Amplifier (PoE) Setup
2.2.9 Loudspeaker Type
Using the amplified output, the CyberData SIP Loudspeaker Amplifier (PoE) supports the 011068
Loudspeaker or equivalent unamplified loudspeaker.
Figure 2-17. 011068 Loudspeaker
2.2.10 Cabling/Wiring
Using the amplified output, you may connect a 011068 loudspeaker or equivalent unamplified
speaker to a SIP Loudspeaker Amplifier (PoE-powered) with good quality speaker wire that is 16
gauge and limited to 25 feet in length with two loudspeakers or 50 feet in length with one
loudspeaker.
Operations Guide
931236H
CyberData Corporation
Installing the SIP Loudspeaker Amplifier (PoE) 22
SIP Loudspeaker Amplifier (PoE) Setup
2.2.11 Confirm Operation
After connecting the device to the 802.3af compliant ethernet hub, use the LEDs on the device to
confirm that the device is operational and linked to the network.
Table 2-7. SIP Loudspeaker Amplifier (PoE) LEDs
LED
Color
Function
Power (PWR)
BLUE/GREEN
The 802.3at power injector that is provided with the device should
cause the Power (PWR) LED to illuminate BLUE to indicate that high
power is available.
The Power (PWR) LED may illuminate GREEN if a low power mode
(802.3af) power source is used (not included and sold separately).
GREEN
Status
After supplying power to the device, a steady GREEN Status LED
illuminates.
After about 20 seconds, the GREEN Status LED will blink fast to
indicate that the device is acquiring an IP address and attempting to
autoprovision. The GREEN Status LED will turn off thereafter until
the device has finished booting. When the device has fully booted,
the GREEN Status LED will turn on solid to confirm the device is
operational.
The GREEN Status LED will blink during a page when it is online.
Speed (SPD)
AMBER
The Speed (SPD) LED illuminates AMBER for a 100Mb link or is off
for 10MB when the network link to the device is established.
Link/Activity (Link/Act.)
GREEN
The Link/Activity (Link/Act.) GREEN LED blinks to indicate
network traffic.
Figure 2-18. SIP Loudspeaker Amplifier (PoE) LEDs
Volume
Speed (SPD) LED
(AMBER)
Power (PWR) LED
(BLUE/GREEN)
Operations Guide
SPD Link/Act
PWR
931236H
Status
Link/Activity (Link/Act.) LED
(GREEN)
Status LED
(GREEN)
CyberData Corporation
Installing the SIP Loudspeaker Amplifier (PoE) 23
SIP Loudspeaker Amplifier (PoE) Setup
2.2.12 Confirm the IP Address and Test the Audio
2.2.12.1 RTFM Switch
When the SIP Loudspeaker Amplifier (PoE) is operational and linked to the network, use the Reset
Test Function Management (RTFM) switch (Figure 2-19) (located behind the hole on the device) to
announce and confirm the device’s IP Address and test the audio to verify that it is working.
Figure 2-19. RTFM Switch
RTFM switch 
(located behind the hole 
on the device)
Announcing the IP To announce a device’s current IP address:
Address
•
Use a bent paperclip or a similar object to press and hold the RTFM switch for a couple of
seconds and then release it.
Caution
GENERAL ALERT
Restoring the
Factory Default
Settings
Equipment Caution: Pressing and holding the RTFM switch for more than five
seconds will restore the device to the factory default settings. See the “Restoring
the Factory Default Settings” section.
To restore the factory default settings, complete the following steps:
1. Use a bent paperclip or a similar object to press and hold the RTFM switch until you hear the
device announce the words, “restoring defaults” and “rebooting”.
2. Release the RTFM switch. The device will be restored to the factory default settings.
Operations Guide
931236H
CyberData Corporation
Installing the SIP Loudspeaker Amplifier (PoE) 24
SIP Loudspeaker Amplifier (PoE) Setup
2.2.13 Adjust the Volume
There are two ways to adjust the volume for the SIP Loudspeaker Amplifier (PoE):
•
The SIP Volume setting on the Device Page
•
The external Volume dial (Figure 2-21) on the SIP Loudspeaker Amplifier (PoE) face
Figure 2-20. External Volume Dial
Volume
SPD Link/Act
External volume dial
PWR
Status
2.2.13.1 The SIP Volume Setting
To adjust the volume of the device with the SIP Volume setting on the Device Page, complete the
following steps:
1. Go to the Home Page.
2. Select the Device Page page.
3. In the SIP Volume box, type a number between 0 (lowest) and 9 (highest).
4. Select Save.
2.2.13.2 The Multicast Volume Setting
To adjust the Multicast Volume volume with the Multicast Volume setting on the Device Page,
complete the following steps:
1. Go to the Home Page.
2. Select the Device Page.
3. In the Multicast Volume box, type a number between 0 (lowest) and 9 (highest).
4. Select Save.
Operations Guide
931236H
CyberData Corporation
Installing the SIP Loudspeaker Amplifier (PoE) 25
SIP Loudspeaker Amplifier (PoE) Setup
2.2.13.3 The Ring Volume Setting
To adjust the Ring Volume volume with the Ring Volume setting on the Device Page, complete the
following steps:
1. Go to the Home Page.
2. Select the Device Page.
3. In the Multicast Volume box, type a number between 0 (lowest) and 9 (highest).
4. Select Save.
2.2.13.4 The Sensor Volume Setting
To adjust the Sensor Volume volume with the Sensor Volume setting on the Device Page,
complete the following steps:
1. Go to the Home Page.
2. Select the Device Page.
3. In the Sensor Volume box, type a number between 0 (lowest) and 9 (highest).
4. Select Save.
2.2.13.5 The Loopback Volume Setting
To adjust the Loopback Volume volume with the Loopback Volume setting on the Device Page,
complete the following steps:
1. Go to the Home Page.
2. Select the Device Page.
3. In the Loopback Volume box, type a number between 0 (lowest) and 9 (highest).
4. Select Save.
2.2.13.6 External Volume Dial
To adjust the SIP Loudspeaker Amplifier (PoE) volume with the external volume dial, complete the
following steps:
1. Turn the external Volume dial (Figure 2-20) on the SIP Loudspeaker Amplifier (PoE) face.
Note
Operations Guide
For the lineout volume, the volume is fixed and the volume control is adjusted through an
external amplifier.
931236H
CyberData Corporation
Installing the SIP Loudspeaker Amplifier (PoE) 26
SIP Loudspeaker Amplifier (PoE) Setup
Figure 2-21. External Volume Dial
Volume
SPD Link/Act
External volume dial
PWR
Operations Guide
931236H
Status
CyberData Corporation
Installing the SIP Loudspeaker Amplifier (PoE) 27
SIP Loudspeaker Amplifier (PoE) Setup
2.3 Configure the SIP Loudspeaker Amplifier (PoE)
Parameters
To configure the SIP Loudspeaker Amplifier (PoE) online, use a standard web browser.
Configure each SIP Loudspeaker Amplifier (PoE) and verify its operation before you mount it. When
you are ready to mount an SIP Loudspeaker Amplifier (PoE), refer to Appendix A, "Mounting the
Amplifier" for instructions.
2.3.1 Factory Default Settings
All SIP Loudspeaker Amplifier (PoE)s are initially configured with the following default IP settings:
When configuring more than one SIP Loudspeaker Amplifier (PoE), attach the SIP Loudspeaker
Amplifier (PoE)s to the network and configure one at a time to avoid IP address conflicts.
Table 2-8. Factory Default Settings
Parameter
Factory Default Setting
IP Addressing
DHCP
IP Addressa
10.10.10.10
Web Access Username
admin
Web Access Password
admin
Subnet Maska
255.0.0.0
Default Gatewaya
10.0.0.1
a. Default if there is not a DHCP server present.
Operations Guide
931236H
CyberData Corporation
Installing the SIP Loudspeaker Amplifier (PoE) 28
SIP Loudspeaker Amplifier (PoE) Setup
2.3.2 SIP Loudspeaker Amplifier (PoE) Web Page Navigation
Table 2-9 shows the navigation buttons that you will see on every SIP Loudspeaker Amplifier (PoE)
web page.
Table 2-9. Web Page Navigation
Web Page Item
Description
Link to the Home page.
Link to the Device page.
Link to the Network page.
Link to go to the SIP page.
Link to the Multicast page.
Link to the Sensor page.
Link to the Audiofiles page.
Link to the Events page.
Link to the Autoprovisioning page.
Link to the Firmware page.
Operations Guide
931236H
CyberData Corporation
Installing the SIP Loudspeaker Amplifier (PoE) 29
SIP Loudspeaker Amplifier (PoE) Setup
2.3.3 Using the Toggle Help Button
The Toggle Help button allows you to see a short description of some of the settings on the
webpage. To use the Toggle Help button, do the following:
1. Click on the Toggle Help button that is on the UI webpage. See Figure 2-22 and Figure 2-23.
Figure 2-22. Toggle/Help Button
2. You will see a question mark ( ) appear next to each web page item that has been provided
with a short description by the Help feature. See Figure 2-23.
Figure 2-23. Toggle Help Button and Question Marks
Question mark 
appears next to the
web page items
Toggle Help button
Operations Guide
931236H
CyberData Corporation
Installing the SIP Loudspeaker Amplifier (PoE) 30
SIP Loudspeaker Amplifier (PoE) Setup
3. Move the mouse pointer to hover over the question mark (
page item will appear. See Figure 2-24.
), and a short description of the web
Figure 2-24. Short Description Provided by the Help Feature
Question mark
Operations Guide
931236H
A short description of the 
web page item will appear
CyberData Corporation
Installing the SIP Loudspeaker Amplifier (PoE) 31
SIP Loudspeaker Amplifier (PoE) Setup
2.3.4 Using the Toggle Help Button
The Toggle Help button allows you to see a short description of some of the settings on the
webpage. To use the Toggle Help button, do the following:
1. Click on the Toggle Help button that is on the UI webpage. See Figure 2-22 and Figure 2-23.
Figure 2-25. Toggle/Help Button
2. You will see a question mark ( ) appear next to each web page item that has been provided
with a short description by the Help feature. See Figure 2-23.
Figure 2-26. Toggle Help Button and Question Marks
Question mark 
appears next to the
web page items
Toggle Help button
Operations Guide
931236H
CyberData Corporation
Installing the SIP Loudspeaker Amplifier (PoE) 32
SIP Loudspeaker Amplifier (PoE) Setup
3. Move the mouse pointer to hover over the question mark (
page item will appear. See Figure 2-24.
), and a short description of the web
Figure 2-27. Short Description Provided by the Help Feature
Question mark
Operations Guide
931236H
A short description of the 
web page item will appear
CyberData Corporation
Installing the SIP Loudspeaker Amplifier (PoE) 33
SIP Loudspeaker Amplifier (PoE) Setup
2.3.5 Log in to the Home Page
1. Open your browser to the device IP address.
Note
If the network does not have access to a DHCP server, the device will default to an IP
address of 10.10.10.10.
Note
Make sure that the PC is on the same IP network as the SIP Loudspeaker Amplifier (PoE).
Note
You may also download CyberData’s VoIP Discovery Utility program which allows you to
easily find and configure the default web address of the CyberData VoIP products. 

CyberData’s VoIP Discovery Utility program is available at the following website address:
http://www.cyberdata.net/assets/common/discovery.zip
Note
The device ships in DHCP mode. To get to the Home page, use the discovery utility to scan
for the device on the network and open your browser from there.
2. When prompted, use the following default Web Access Username and Web Access
Password to access the Home Page (Figure 2-28):
Web Access Username: admin
Web Access Password: admin
Operations Guide
931236H
CyberData Corporation
Installing the SIP Loudspeaker Amplifier (PoE) 34
SIP Loudspeaker Amplifier (PoE) Setup
Figure 2-28. Home Page
CyberData Paging Amplifier
405100001
v11.6.4
Operations Guide
931236H
CyberData Corporation
Installing the SIP Loudspeaker Amplifier (PoE) 35
SIP Loudspeaker Amplifier (PoE) Setup
3. On the Home page, review the setup details and navigation buttons described in Table 2-10.
Note
The question mark icon ( ) in the following table shows which web page items will be defined
after the Toggle Help button is pressed.
Table 2-10. Home Page Overview
Web Page Item
Description
Admin Settings
Username
The username to access the web interface. Enter up to 25 characters.
Password
The password to access the web interface. Enter up to 25 characters.
Confirm Password
Confirm the web interface password.
Current Status
Serial Number
Shows the device serial number.
Mac Address
Shows the device Mac address.
Firmware Version
Shows the current firmware version.
IP Addressing
Shows the current IP addressing setting (DHCP or static).
IP Address
Shows the current IP address.
Subnet Mask
Shows the current subnet mask address.
Default Gateway
Shows the current default gateway address.
DNS Server 1
Shows the current DNS Server 1 address.
DNS Server 2
Shows the current DNS Server 2 address.
SIP Mode
Shows the current status of the SIP mode.
Multicast Mode
Shows the current status of the Multicast mode.
Event Reporting
Shows the current status of the Event Reporting mode.
Nightringer
Shows the current status of the Nightringer mode.
Primary SIP Server
Shows the current status of the Primary SIP Server.
Backup Server 1
Shows the current status of Backup Server 1.
Backup Server 2
Shows the current status of Backup Server 2.
Nightringer Server
Shows the current status of Nightringer Server.
Import Settings
Use this button to select a configuration file to import.
After selecting a configuration file, click Import to import the
configuration from the selected file. Then, click Save and Reboot to
store changes.
Export Settings
Click Export to export the current configuration to a file.
Click the Save button to save your configuration settings.
Note: You need to reboot for changes to take effect.
Operations Guide
931236H
CyberData Corporation
Installing the SIP Loudspeaker Amplifier (PoE) 36
SIP Loudspeaker Amplifier (PoE) Setup
Table 2-10. Home Page Overview (continued)
Web Page Item
Description
Click on the Reboot button to reboot the system.
Click on the Toggle Help button to see a short description of some of
the web page items. First click on the Toggle Help button, and you will
see a question mark ( ) appear next to some of the web page items.
Move the mouse pointer to hover over a question mark to see a short
description of a specific web page item.
Operations Guide
931236H
CyberData Corporation
Installing the SIP Loudspeaker Amplifier (PoE) 37
SIP Loudspeaker Amplifier (PoE) Setup
2.3.6 Configure the Device
1. Click the Device menu button to open the Device page. See Figure 2-29.
Figure 2-29. Device Page
Operations Guide
931236H
CyberData Corporation
Installing the SIP Loudspeaker Amplifier (PoE) 38
SIP Loudspeaker Amplifier (PoE) Setup
2. On the Device page, you may enter values for the parameters indicated in Table 2-11.
Note
The question mark icon (
) in the following table shows which web page items will be defined
after the Toggle Help button is pressed.
Table 2-11. Device Page Parameters
Web Page Item
Description
Volume Settings (0-9)
Disable Volume Control Dial
Select this option to disable the volume control dial and enable digital
volume control settings.
SIP Volume
Set the speaker volume for a SIP call. A value of 0 will mute the speaker
during SIP calls.
Multicast Volume
Set the speaker volume for multicast audio streams. A value of 0 will mute
the speaker during multicasts.
Ring Volume
Set the ring volume for incoming calls. A value of 0 will mute the speaker
instead of playing the ring tone when Auto-Answer Incoming Calls is
disabled.
Sensor Volume
Set the speaker volume for playing sensor activated audio. A value of 0
will mute the speaker during sensor activated audio.
Loopback Volume
Speaker volume for Line-in Loopback. This value only affects the volume
of the speaker(s). Line-out volume must be controlled by the amplifier
connected to the line-out port.
Volume Boost:
Set the Boost level to increase the volume output of the speaker. Using
Volume Boost may introduce audio clipping and/or distortion. Boost is
only recommended for use with volumes set to level 9.
No Volume Boost
+4dB
Clock Settings
Set Time with NTP Server on boot
When selected, the time is set with an external NTP server when the
device restarts.
NTP Server
Use this field to set the address (in IPv4 dotted decimal notation or as a
canonical name) for the NTP Server. This field can accept canonical
names of up to 64 characters in length.
Posix Timezone String
See Section 2.3.6.1, "Time Zone Strings" for information about how to
use the Posix Timezone String to specify time zone and daylight savings
time where applicable. Enter up to 63 characters.
Periodically sync time with server
When selected, the time is periodically updated with the NTP server at
the configured interval below.
Time update period (in hours)
The time interval after which the device will contact the NTP server to
update the time. Enter up to 4 digits.
Current Time
Allows you to input the current time. (6 character limit)
Power Settings
802.3AT Mode
Operations Guide
This device automatically detects if it is plugged into an 802.3AT (also
known as PoE Plus) power source. 802.3AT provides more power than
older 802.3AT power sources and allows this speaker to play audio at
higher volumes. If you are sure this speaker is connected to an 802.3AT
power source, but it is not being detected correctly, you can override the
automatic settings below.
931236H
CyberData Corporation
Installing the SIP Loudspeaker Amplifier (PoE) 39
SIP Loudspeaker Amplifier (PoE) Setup
Table 2-11. Device Page Parameters (continued)
Web Page Item
Description
Force 802.3AT Mode (NOT recommended)
Enable this option if you are sure this speaker is connected to an 802.3AT
power source, but it is not being detected correctly (not recommended).
Auxiliary Power Supply
This device can be connected to a +24VDC auxiliary power supply.
Check this box if this is how this speaker is being powered.
Line-In Settings
Enable Line-in to Line-out Loopback
Line-in audio will play back out the device's audio output ports. This is the
lowest priority audio and will be preempted by any other audio stream.
DTMF Settings
Require Security Code
When selected, the user will be prompted to enter a Security Code
(entered on this page) before being able to execute a page when calling
the device.
Security Code
Type the Security Code in this field. The Security Code must only use
characters '0-9', '*' and '#'. Enter up to 25 characters.
Enable Stored Message Playback
When selected, the caller will be prompted to select one of nine stored
messages to play through the speaker. Stored messages may be
customized on the Audiofiles page.
Relay Settings
Activate Relay with DTMF Code
Activates the relay when the DTMF Activation Code is entered on the
phone during a SIP call with the device. RFC2833 DTMF payload types
are supported.
Relay Pulse Code
DTMF code used to pulse the relay when entered on a phone during a
SIP call with the device. Relay will activate for Relay Pulse Duration
seconds then deactivate. Activate Relay with DTMF Code must be
enabled. Enter up to 25 digits (* and # are supported).
Relay Pulse Duration (in seconds)
The length of time (in seconds) during which the relay will be activated
when the DTMF Relay Activation Code is detected. Enter up to 5 digits.
Relay Activation Code
Activation code used to activate the relay when entered on a phone
during a SIP call with the device. Relay will be active indefinitely, or until
the DTMF Relay Deactivation code is entered. Activate Relay with DTMF
Code must be enabled. Enter up to 25 digits (* and # are supported).
Relay Deactivation Code
Code used to deactivate the relay when entered on a phone during a SIP
call with the device. Activate Relay with DTMF Code must be enabled.
Enter up to 25 digits (* and # are supported).
Activate Relay During Ring
When selected, the relay will be activated for as long as the device is
ringing. When Auto-Answer Incoming Calls is enabled, the device will not
ring and this option does nothing.
Activate Relay During Night Ring
When selected, the relay will be activated as long as the Nightringer
extension is ringing.
Activate Relay While Call Active
When selected, the relay will be activated as long as the SIP call is active.
Misc Settings
Device Name
Type the device name. Enter up to 25 characters.
Auto-Answer Incoming Calls
When selected, the device will automatically answer incoming calls.
When Auto-Answer Incoming Calls is disabled, the device will play a
ring tone (corresponds to Ring Tone on the Audiofiles page) out of the
speaker.
Operations Guide
931236H
CyberData Corporation
Installing the SIP Loudspeaker Amplifier (PoE) 40
SIP Loudspeaker Amplifier (PoE) Setup
Table 2-11. Device Page Parameters (continued)
Web Page Item
Description
Beep on Init
Device will play the user-defined “pagetone” audio file when it boots.
Beep on Page
Device will play the user defined “pagetone” audio file before playing a
SIP page.
Disable HTTPS (NOT recommended)
Disables the encrypted connection to the webpage. We do not
recommend disabling HTTPS for security reasons.
Two Speakers Connected
Specify if one or two speakers are connected to the paging amplifier. If
only one is connected, ensure that it is wired to the first set of terminal
blocks.
RGB Strobe
Status of optional RGB Strobe.
Click on the Test Audio button to do an audio test. When the Test Audio
button is pressed, you will hear a voice message for testing the device
audio quality and volume.
Click on the Test Relay button to do a relay test.
Click the Save button to save your configuration settings.
Note: You need to reboot for changes to take effect.
Click on the Reboot button to reboot the system.
Click on the Toggle Help button to see a short description of some of the
web page items. First click on the Toggle Help button, and you will see a
question mark ( ) appear next to some of the web page items. Move the
mouse pointer to hover over a question mark to see a short description of
a specific web page item.
Note
Operations Guide
You can change the SIP Volume, Multicast Volume, Ring Volume, and Sensor Volume
without rebooting the device. You must save and reboot the device for other changes to take
effect.
931236H
CyberData Corporation
Installing the SIP Loudspeaker Amplifier (PoE) 41
SIP Loudspeaker Amplifier (PoE) Setup
2.3.6.1 Time Zone Strings
The posix time zone string tells the internal date and time utilities how to handle daylight savings
time for different time zones. Table 2-24 shows some common strings.
Table 2-12. Common Time Zone Strings
Time Zone
Time Zone String
US Pacific time
PST8PDT,M3.2.0/2:00:00,M11.1.0/2:00:00
US Mountain time
MST7MDT,M3.2.0/2:00:00,M11.1.0/2:00:00
US Eastern Time
EST5EDT,M3.2.0/2:00:00,M11.1.0/2:00:00
a
Phoenix Arizona
MST7
US Central Time
CST6DST,M3.2.0/2:00:00,M11.1.0/2:00:00
a.Phoenix, Arizona does not use daylight savings time.
Table 2-25 shows a breakdown of the parts that constitute the following time zone string:
●
CST6DST,M3.2.0/2:00:00,M11.1.0/2:00:00
Table 2-13. Time Zone String Parts
Operations Guide
Time Zone String
Part
Meaning
CST6CDT
The time zone offset from GMT and three character identifiers for the time zone.
CST
Central Standard Time
6
The (hour) offset from GMT/UTC
CDT
Central Daylight Time
M3.2.0/2:00:00
The date and time when daylight savings begins.
M3
The third month (March)
.2
The 2nd occurrence of the day (next item) in the month
.0
Sunday
/2:00:00
Time of day to change
M11.1.0/2:00:00
The date and time when daylight savings ends.
M11
The eleventh month (November)
.1
The 1st occurrence of the day (next item) in the month
.0
Sunday
/2:00:00
Time of day to change
931236H
CyberData Corporation
Installing the SIP Loudspeaker Amplifier (PoE) 42
SIP Loudspeaker Amplifier (PoE) Setup
Time Zone String
Examples
Table 2-26 has some more examples of time zone strings.
Table 2-14. Time Zone String Examples
Time Zone
Time Zone String
a
Tokyo
IST-9
Berlinb
CET-1MET,M3.5.0/1:00,M10.5.0/1:00
a.Tokyo does not use daylight savings time.
b.For Berlin, daylight savings time starts on the last Sunday in March at
01:00 UTC, and ends on the last Sunday in October at 01:00 UTC, and is one
hour ahead of UTC.
Time Zone Identifier A user-definable three or four character time zone identifier (such as PST, EDT, IST, MUT, etc) is
needed at the beginning of the posix time zone string to properly set the time. However, the specific
letters or numbers used for the time zone identifier are not important and can be any three or four
letter or number combination that is chosen by the user. However, the time zone identifier cannot be
blank.
Figure 2-30. Three or Four Character Time Zone Identifier
You can also use the following URL when a certain time zone applies daylight savings time:
http://www.timeanddate.com/time/dst/2011.html
World GMT Table
Table 2-27 has information about the GMT time in various time zones.
Table 2-15. World GMT Table
Operations Guide
Time Zone
City or Area Zone Crosses
GMT-12
Eniwetok
GMT-11
Samoa
GMT-10
Hawaii
GMT-9
Alaska
GMT-8
PST, Pacific US
GMT-7
MST, Mountain US
GMT-6
CST, Central US
GMT-5
EST, Eastern US
GMT-4
Atlantic, Canada
GMT-3
Brazilia, Buenos Aries
GMT-2
Mid-Atlantic
GMT-1
Cape Verdes
GMT
Greenwich Mean Time, Dublin
GMT+1
Berlin, Rome
GMT+2
Israel, Cairo
GMT+3
Moscow, Kuwait
GMT+4
Abu Dhabi, Muscat
931236H
CyberData Corporation
Installing the SIP Loudspeaker Amplifier (PoE) 43
SIP Loudspeaker Amplifier (PoE) Setup
Table 2-15. World GMT Table (continued)
Operations Guide
Time Zone
City or Area Zone Crosses
GMT+5
Islamabad, Karachi
GMT+6
Almaty, Dhaka
GMT+7
Bangkok, Jakarta
GMT+8
Hong Kong, Beijing
GMT+9
Tokyo, Osaka
GMT+10
Sydney, Melbourne, Guam
GMT+11
Magadan, Soloman Is.
GMT+12
Fiji, Wellington, Auckland
931236H
CyberData Corporation
Installing the SIP Loudspeaker Amplifier (PoE) 44
SIP Loudspeaker Amplifier (PoE) Setup
2.3.7 Configure the Network Parameters
1. Click the Network menu button to open the Network page (Figure 2-31).
Figure 2-31. Network Page
Operations Guide
931236H
CyberData Corporation
Installing the SIP Loudspeaker Amplifier (PoE) 45
SIP Loudspeaker Amplifier (PoE) Setup
2. On the Network page, enter values for the parameters indicated in Table 2-16.
Note
The question mark icon ( ) in the following table shows which web page items will be defined
after the Toggle Help button is pressed.
Table 2-16. Network Page Parameters
Web Page Item
Description
Stored Network Settings
Addressing Mode
Select either DHCP IP Addressing or Static Addressing by marking
the appropriate radio button. DHCP Addressing mode is enabled on
default and the device will attempt to resolve network addressing with
the local DHCP server upon boot. If DHCP Addressing fails, the
device will revert to the last known IP address or the factory default
address if no prior DHCP lease was established. See Section 2.3.1,
"Factory Default Settings" for factory default settings. Be sure to click
Save and Reboot to store changes when configuring a Static
address.
Hostname
This is the hostname provided by the DHCP server. See the
DHCP/DNS server documentation for more information. Enter up to
64 characters.
IP Address
Enter the Static IPv4 network address in dotted decimal notation.
Subnet Mask
Enter the Subnet Mask in dotted decimal notation.
Default Gateway
Enter the Default Gateway IPv4 address in dotted decimal notation.
DNS Server 1
Enter the primary DNS Server IPv4 address in dotted decimal
notation.
DNS Server 2
Enter the secondary DNS Server IPv4 address in dotted decimal
notation.
DHCP Timeout in seconds
Specify the desired time-out duration (in seconds) that the device will
wait for a response from the DHCP server before reverting back to
the stored static IP address. The stored static IP address may be the
last known IP address or the factory default address if no prior DHCP
lease was established. Enter up to 8 characters. A value of -1 will
retry forever.
Current Network Settings
Shows the current network settings.
IP Address
Shows the current Static IP address.
Subnet Mask
Shows the current Subnet Mask address.
Default Gateway
Shows the current Default Gateway address.
DNS Server 1
Shows the current DNS Server 1 address.
DNS Server 2
Shows the current DNS Server 2 address.
VLAN Settings
VLAN ID (0-4095)
Specify the IEEE 802.1Q VLAN ID number. Enter up to 4 digits.
Note: The device supports 802.1Q VLAN tagging support. The
switch port connected to the device will need to be in “trunking mode”
for the VLAN tags to propagate.
VLAN Priority (0-7)
Operations Guide
Specify the IEEE 802.1p VLAN priority level. Enter 1 digit. A value of
0 may cause the VLAN ID tag to be ignored.
931236H
CyberData Corporation
Installing the SIP Loudspeaker Amplifier (PoE) 46
SIP Loudspeaker Amplifier (PoE) Setup
Table 2-16. Network Page Parameters (continued)
Web Page Item
Description
Click the Save button to save your configuration settings.
Note: You need to reboot for changes to take effect.
Click on the Reboot button to reboot the system.
Click on the Toggle Help button to see a short description of some of
the web page items. First click on the Toggle Help button, and you
will see a question mark ( ) appear next to some of the web page
items. Move the mouse pointer to hover over a question mark to see
a short description of a specific web page item.
Note
Operations Guide
You must click on the Save button and then the Reboot button for the changes to take
effect.
931236H
CyberData Corporation
Installing the SIP Loudspeaker Amplifier (PoE) 47
SIP Loudspeaker Amplifier (PoE) Setup
2.3.8 Configure the SIP (Session Initiation Protocol) Parameters
1. Click on the SIP menu button to open the SIP page (Figure 2-32).
Figure 2-32. SIP Page
Operations Guide
931236H
CyberData Corporation
Installing the SIP Loudspeaker Amplifier (PoE) 48
SIP Loudspeaker Amplifier (PoE) Setup
2. On the SIP page, enter values for the parameters indicated in Table 2-17.
Note
The question mark icon ( ) in the following table shows which web page items will be defined
after the Toggle Help button is pressed.
Table 2-17. SIP Page Parameters
Web Page Item
Description
SIP Settings
Enable SIP Operation
When enabled, the device will transmit, receive, and process SIP
messages according to the configured SIP settings below.
Register with a SIP Server
When enabled, the device will attempt to register to the configured SIP
Server(s) on this page. To configure the device to send and receive pointto-point SIP calls, enable SIP Operation and disable Register with a SIP
Server (see Section 2.3.8.2, "Point-to-Point Configuration").
Use Cisco SRST
When enabled, the backup servers are handled according to Cisco SRST
(Survivable Remote Site Telephony). It is required for use in clustered
Cisco Unified Communications Manager topologies.
Primary SIP Server
Enter the SIP server address as an IPv4 address in dotted decimal
notation or a fully qualified domain name. This parameter also becomes
the host portion of the SIP-URI for the device's extension on the primary
SIP server. This field can accept entries of up to 255 characters in length.
Primary SIP User ID
Specify the SIP User ID for the Primary SIP Server. This parameter
becomes the user portion of the SIP-URI for the device's extension on the
primary SIP server. Enter up to 64 alphanumeric characters.
Primary SIP Auth ID
Specify the Authenticate ID for the Primary SIP Server. This parameter is
required for SIP registration authentication. Enter up to 64 alphanumeric
characters.
Primary SIP Auth Password
Specify the Authenticate Password for the Primary SIP Server. This
parameter is required for SIP registration authentication. Enter up to 64
alphanumeric characters.
Backup SIP Server 1
Enter the backup SIP server address as an IPv4 address in dotted
decimal notation or a fully qualified domain name. This parameter also
becomes the host portion of the SIP-URI for the device's extension on the
backup SIP server. This field can accept entries of up to 255 characters in
length.
Backup SIP User ID 1
Specify the SIP User ID for the first backup SIP Server. This parameter
becomes the user portion of the SIP-URI for the device's extension on the
first backup SIP server. Enter up to 64 alphanumeric characters.
Backup SIP Auth ID 1
Specify the Authenticate ID for the first backup SIP server. This parameter
is required for SIP registration authentication. Enter up to 64 alphanumeric
characters.
Backup SIP Auth Password 1
Specify the Authenticate Password for the first backup SIP server. This
parameter is required for SIP registration authentication. Enter up to 64
alphanumeric characters.
Backup SIP Server 2
Enter a second backup SIP server address as an IPv4 address in dotted
decimal notation or a fully qualified domain name. This parameter also
becomes the host portion of the SIP-URI for the device's extension on the
second backup SIP server. This field can accept entries of up to 255
characters in length.
Operations Guide
931236H
CyberData Corporation
Installing the SIP Loudspeaker Amplifier (PoE) 49
SIP Loudspeaker Amplifier (PoE) Setup
Table 2-17. SIP Page Parameters (continued)
Web Page Item
Description
Backup SIP User ID 2
Specify the SIP User ID for the second backup SIP Server. This parameter
becomes the user portion of the SIP-URI for the device's extension on the
second backup SIP server. Enter up to 64 alphanumeric characters.
Backup SIP Auth ID 2
Specify the Authenticate ID for the second backup SIP server. This
parameter is required for SIP registration authentication. Enter up to 64
alphanumeric characters.
Backup SIP Auth Password 2
Specify the Authenticate Password for the second backup SIP server. This
parameter is required for SIP registration authentication. Enter up to 64
alphanumeric characters.
Remote SIP Port
The Remote SIP Port is the port number the device will use as the
destination port when sending SIP messages. The default Remote SIP
Port is 5060. The supported range is 0-65536. Enter up to 5 digits.
Local SIP Port
The Local SIP Port is the port number the device will use to receive SIP
messages. The default Local SIP Port is 5060. The supported range is 065536. Enter up to 5 digits.
Outbound Proxy
Enter the Outbound Proxy address as an IPv4 address in dotted decimal
notation or a fully qualified domain name (FQDN). When an IP address is
configured, the device will send all SIP messages to this IP address.
When an FQDN is configured, the device will run DNS NAPTR, SRV, and
A queries on the FQDN to resolve an IP address to which it will send all
SIP messages. This field can accept entries of up to 255 characters in
length.
Outbound Proxy Port
The Outbound Proxy Port is port number used as the destination port
when sending SIP messages to the outbound proxy. A value of 0 will
default to 5060. The supported range is 0-65536. Enter up to 5 digits.
Disable rport Discovery
Disabling rport Discovery will prevent the device from including the public
WAN IP address and port number in the contact information that is sent to
the remote SIP servers. This will generally only need to be enabled when
using an SBC or SIP ALG in conjunction with a remote SIP server.
Buffer SIP Calls
Also referred to as delayed paging. Device will buffer up to 4 minutes of
audio then play back the recording after hang up.
Re-registration Interval (in seconds)
The SIP Re-registration interval (in seconds) is the SIP Registration lease
time, also known as the expiry. The supported range is 30-3600 seconds.
Enter up to 4 digits.
Unregister on Boot
When enabled, the device will send one registration with an expiry of 0 on
boot.
Keep Alive Period
The minimum time in milliseconds between keep-alive packets sent for nat
traversal. A value of 0 will disable keep alive packets.
SIP Strobe Settings
Blink Strobe on Ring
When selected, the Strobe will blink a scene when ringing.
Scene
Select desired scene (only one may be chosen).
ADA Compliant
Strobe will blink ON at the specified brightness for 150ms then OFF for
350ms during the duration of the event.
Slow Fade
Strobe will increase in brightness from 0 to the specified brightness and
back to 0 over the course of about 3.5 seconds during the duration of the
event.
Operations Guide
931236H
CyberData Corporation
Installing the SIP Loudspeaker Amplifier (PoE) 50
SIP Loudspeaker Amplifier (PoE) Setup
Table 2-17. SIP Page Parameters (continued)
Web Page Item
Description
Fast Fade
Strobe will increase in brightness from 0 to the specified brightness and
back to 0 over the course of about 1.5 seconds during the duration of the
event.
Slow Blink
Strobe will blink ON at the specified brightness for one second then OFF
for one second during the duration of the event.
Fast Blink
Strobe will blink ON at the specified brightness then OFF five times per
second during the duration of the event.
Color
Select desired color (only one may be chosen).
Brightness
How bright the strobe will blink when there is a SIP Call. This is the
maximum brightness for “fade” type scenes.
Red
The red LED value for SIP Call.
Green
The green LED value for SIP Call.
Blue
The blue LED value for SIP Call.
Use this button to preview the strobe flashing behavior for the MWI Strobe
Settings.
MWI Strobe Settings
Blink Strobe on MWI
When selected, the strobe will blink a scene when a voicemail is waiting
for its extension.
Scene
Select desired scene (only one may be chosen).
ADA Compliant
Strobe will blink ON at the specified brightness for 150ms then OFF for
350ms during the duration of the event.
Slow Fade
Strobe will increase in brightness from 0 to the specified brightness and
back to 0 over the course of about 3.5 seconds during the duration of the
event.
Fast Fade
Strobe will increase in brightness from 0 to the specified brightness and
back to 0 over the course of about 1.5 seconds during the duration of the
event.
Slow Blink
Strobe will blink ON at the specified brightness for one second then OFF
for one second during the duration of the event.
Fast Blink
Strobe will blink ON at the specified brightness then OFF five times per
second during the duration of the event.
MWI Call Color
Select desired color (only one may be chosen).
Brightness
How bright the strobe will blink when there is a message waiting. This is
the maximum brightness for “fade” type scenes.
Red
The red LED value for MWI.
Green
The green LED value for MWI.
Blue
The blue LED value for MWI.
Use this button to preview the strobe flashing behavior for the MWI Strobe
Settings.
Nightringer Settings
Operations Guide
931236H
CyberData Corporation
Installing the SIP Loudspeaker Amplifier (PoE) 51
SIP Loudspeaker Amplifier (PoE) Setup
Table 2-17. SIP Page Parameters (continued)
Web Page Item
Description
Enable Nightringer
When Nightringer is enabled, the device will attempt to register a second
extension with the SIP server. Any calls made to this extension will play a
ringtone (corresponds to Night Ring on the Audiofiles page). By design,
it is not possible to answer a call to the Nightringer extension.
SIP Server
Enter the SIP server address as an IPv4 address in dotted decimal
notation or a fully qualified domain name. This parameter also becomes
the host portion of the SIP-URI for the device's Nightringer extension on
the SIP server. This field can accept entries of up to 255 characters in
length.
Remote SIP Port
The Remote SIP Port is the port number the device will use as the
destination port when sending SIP messages for the Nightringer
extension. The default Remote SIP Port is 5060. The supported range is
0-65536. Enter up to 5 digits.
Local SIP Port
The Local SIP Port is the port number the device will use to receive SIP
messages for the Nightringer extension. This value cannot be the same as
the Local SIP Port for the primary extension. The default Local SIP Port is
5061. The supported range is 0-65536. Enter up to 5 digits.
Outbound Proxy
Enter the Outbound Proxy address as an IPv4 address in dotted decimal
notation or a fully qualified domain name (FQDN). When an IP address is
configured, the device will send all SIP messages to this IP address for the
Nightringer extension. When an FQDN is configured, the device will run
DNS NAPTR, SRV, and A queries on the FQDN to resolve an IP address
to which it will send all SIP messages for the Nightringer extension. This
field can accept entries of up to 255 characters in length.
Outbound Proxy Port
The Outbound Proxy Port is port number used as the destination port
when sending SIP messages to the outbound proxy for the Nightringer
extension. A value of 0 will default to 5060. The supported range is 065536. Enter up to 5 digits.
User ID
Specify the SIP User ID for the SIP server. This parameter becomes the
user portion of the SIP-URI for the device's Nightringer extension. Enter
up to 64 alphanumeric characters.
Authenticate ID
Specify the Authenticate ID for the SIP Server. This parameter is required
for SIP registration authentication. Enter up to 64 alphanumeric
characters.
Authenticate Password
Specify the Authenticate Password for the SIP Server. This parameter is
required for SIP registration authentication. Enter up to 64 alphanumeric
characters.
Re-registration Interval (in seconds)
The SIP Re-registration Interval (in seconds) is the SIP Registration lease
time, also known as the expiry. The supported range is 30-3600 seconds.
Enter up to 4 digits.
Nightringer Strobe Settings
Blink Strobe on Nightring
When selected, the Strobe will blink a scene when the Nightringer is
ringing.
Scene
Select desired scene (only one may be chosen).
ADA Compliant
Strobe will blink ON at the specified brightness for 150ms then OFF for
350ms during the duration of the event.
Operations Guide
931236H
CyberData Corporation
Installing the SIP Loudspeaker Amplifier (PoE) 52
SIP Loudspeaker Amplifier (PoE) Setup
Table 2-17. SIP Page Parameters (continued)
Web Page Item
Description
Slow Fade
Strobe will increase in brightness from 0 to the specified brightness and
back to 0 over the course of about 3.5 seconds during the duration of the
event.
Fast Fade
Strobe will increase in brightness from 0 to the specified brightness and
back to 0 over the course of about 1.5 seconds during the duration of the
event.
Slow Blink
Strobe will blink ON at the specified brightness for one second then OFF
for one second during the duration of the event.
Fast Blink
Strobe will blink ON at the specified brightness then OFF five times per
second during the duration of the event.
Color
Select desired color (only one may be chosen).
Brightness
How bright the strobe will blink when the Nightringer is ringing. This is the
maximum brightness for “fade” type scenes.
Red
The red LED value for Nightringer.
Green
The green LED value for Nightringer.
Blue
The blue LED value for Nightringer.
Use this button to preview the strobe flashing behavior for the Nightringer
Strobe Settings.
RTP Settings
RTP Port (even)
Specify the port number used for the RTP stream after establishing a SIP
call. This port number must be an even number and defaults to 10500.
The supported range is 0-65536. Enter up to 5 digits.
Jitter Buffer
Specify the size of the jitter buffer (in milliseconds) used for SIP calls. Valid
values are 50-1000.
Call Disconnection
Terminate Call After Delay
Automatically terminate an active call after a given delay in seconds. A
value of 0 will disable this function. Enter up to 8 digits.
Codec Selection
Force Selected Codec
When configured, this option will allow you to force the device to negotiate
for the selected codec. Otherwise, the device will perform codec
negotiation using the default list of supported codecs.
Codec
Select the desired codec (only one may be chosen).
Click the Save button to save your configuration settings.
Note: You need to reboot for changes to take effect.
Click on the Reboot button to reboot the system.
Click on the Toggle Help button to see a short description of some of the
web page items. First click on the Toggle Help button, and you will see a
question mark ( ) appear next to some of the web page items. Move the
mouse pointer to hover over a question mark to see a short description of
a specific web page item.
Operations Guide
931236H
CyberData Corporation
Installing the SIP Loudspeaker Amplifier (PoE) 53
SIP Loudspeaker Amplifier (PoE) Setup
Note
You must click on the Save button and then the Reboot button for the changes to take
effect.
Note
For specific server configurations, go to the following website address:
http://www.cyberdata.net/connecting-to-ip-pbx-servers/
2.3.8.1 Dial Out Extension Strings and DTMF Tones (using rfc2833)
On the SIP Page, dial out extensions support the addition of comma delimited pauses and sending
additional DTMF tones (using rfc2833). The first comma will pause three seconds after a call is first
established with a remote device. Subsequent commas will pause for 2 seconds. A pause of one
second will be sent after each numerical digit.
Table 2-18. Examples of Dial-Out Extension Strings
Extension String
Resulting Action
302
Dial out extension 302 and establish a call
302,2
Dial out extension 302 and establish a call, wait 3 seconds then send the
DTMF tone '2'
302,25,,,4,,1
Dial out extension 302 and establish a call, wait 3 seconds then send the
DTMF tone '2', send out DTMF tone 5, wait 6 seconds, send out DTMF
tone 4, wait 4 seconds, send out DTMF tone 1
Note
Operations Guide
The maximum number of total characters in the dial-out field is 64.
931236H
CyberData Corporation
Installing the SIP Loudspeaker Amplifier (PoE) 54
SIP Loudspeaker Amplifier (PoE) Setup
2.3.8.2 Point-to-Point Configuration
When the device is set to not register with a SIP server (see Figure 2-33), it is possible to set the
device to dial out to a single endpoint.
In this case, the dial-out extension should be the IP address of the remote device. The device can
also receive Point-to-Point calls. The delayed DTMF functionality is available in the Point-to-Point
Mode.
Note
Receiving point-to-point SiP calls may not work with all phones.
Figure 2-33. SIP Page Set to Point-to-Point Mode
Device is set to NOT register with a SiP server
Operations Guide
931236H
CyberData Corporation
Installing the SIP Loudspeaker Amplifier (PoE) 55
SIP Loudspeaker Amplifier (PoE) Setup
2.3.8.3 Delayed DTMF
On the SIP page the dial out extension supports the addition of comma delimited pauses and
sending additional DTMF tones (using rfc2833). The first comma will pause three seconds after a
call is first established with a remote device. Subsequent commas will pause for 2 seconds. A pause
of one second will be sent after each numerical digit.
Table 2-19. Examples of Dial-Out Extension Strings
Extension String
Resulting Action
302
Dial out extension 302 and establish a call
302,2
Dial out extension 302 and establish a call, wait 3 seconds then send the
DTMF tone '2'
302,25,,,4,,1
Dial out extension 302 and establish a call, wait 3 seconds then send the
DTMF tone '2', send out DTMF tone 5, wait 6 seconds, send out DTMF
tone 4, wait 4 seconds, send out DTMF tone 1
Note
Operations Guide
The maximum number of total characters in the dial-out field is 25.
931236H
CyberData Corporation
Installing the SIP Loudspeaker Amplifier (PoE) 56
SIP Loudspeaker Amplifier (PoE) Setup
2.3.9 Configure the Multicast Parameters
The Multicast page allows the device to join up to ten paging zones for receiving ulaw/alaw encoded
RTP audio streams.
A paging zone can consist of one or many CyberData multicast group-enabled products. There is no
limit to how many speakers can be in a given paging zone. Each multicast group is defined by a
multicast address and port number.
Each multicast group is assigned a priority, allowing simultaneously arriving pages to be serviced
based on importance. Multicast groups are compatible with IGMP through version 3. The device
supports simultaneous SIP and Multicast.
Operations Guide
931236H
CyberData Corporation
Installing the SIP Loudspeaker Amplifier (PoE) 57
SIP Loudspeaker Amplifier (PoE) Setup
1. Click on the Multicast menu button to open the Multicast page. See Figure 2-34.
Figure 2-34. Multicast Page
Operations Guide
931236H
CyberData Corporation
Installing the SIP Loudspeaker Amplifier (PoE) 58
SIP Loudspeaker Amplifier (PoE) Setup
2. On the Multicast page, enter values for the parameters indicated in Table 2-20.
Note
The question mark icon (
) in the following table shows which web page items will be defined
after the Toggle Help button is pressed.
Table 2-20. Multicast Page Parameters
Web Page Item
Description
Enable Multicast Operation
Enables or disables multicast operation.
Blink Strobe on Multicast
When selected, the Strobe will blink a scene when a multicast is
received.
Priority
Indicates the priority for the multicast group. Priority 9 is the
highest (emergency streams). 0 is the lowest (background
music). SIP calls are considered priority 4.5. See Section 2.3.9.1,
"Assigning Priority" for more details.
Address
Enter the multicast IP Address for this multicast group (15
character limit).
Port
Enter the port number for this multicast group (5 character limit
[range can be from 2000 to 65535]).
Note: The multicast ports have to be even values. The webpage
will enforce this restriction.
Name
Assign a descriptive name for this multicast group (25 character
limit).
Buffer
Device will buffer up to four minutes of audio and then play back
the recording after the multicast stream finishes or after the buffer
is full.
Beep
When selected, the device will play a beep before multicast audio
is sent.
Relay
When selected, the device will activate a relay before multicast
audio is sent.
Scene
Select desired scene (only one may be chosen).
ADA Compliant
Strobe will blink ON at the specified brightness for 150ms then
OFF for 350ms during the duration of the event.
Slow Fade
Strobe will increase in brightness from 0 to the specified
brightness and back to 0 over the course of about 3.5 seconds
during the duration of the event.
Fast Fade
Strobe will increase in brightness from 0 to the specified
brightness and back to 0 over the course of about 1.5 seconds
during the duration of the event.
Slow Blink
Strobe will blink ON at the specified brightness for one second
then OFF for one second during the duration of the event.
Fast Blink
Strobe will blink ON at the specified brightness then OFF five
times per second during the duration of the event.
Color
Select desired color (only one may be chosen).
Brightness
How bright the strobe will blink on a multicast page. This is the
maximum brightness for “fade” type scenes.
Red
The red LED value for Multicast.
Green
The green LED value for Multicast.
Operations Guide
931236H
CyberData Corporation
Installing the SIP Loudspeaker Amplifier (PoE) 59
SIP Loudspeaker Amplifier (PoE) Setup
Table 2-20. Multicast Page Parameters (continued)
Web Page Item
Description
Blue
The blue LED value for Multicast.
Polycom Default Channel
When a default Polycom channel/group number is selected, the
device will subscribe to the default channel for one-way group
pages. Group Numbers 1-25 are supported. Or, select Disabled
to disable this channel.
Polycom Priority Channel
When a priority Polycom channel/group number is selected, the
device will subscribe to the priority channel for one-way group
pages. Group Numbers 1-25 are supported. Or, select Disabled
to disable this channel.
Polycom Emergency Channel
When an emergency Polycom channel/group number is selected,
the device will subscribe to the default channel for one-way group
pages. Group Numbers 1-25 are supported. Or, select Disabled
to disable this channel.
Use this button to preview the strobe flashing behavior for the
Multicast Strobe Settings.
Click the Save button to save your configuration settings.
Note: You need to reboot for changes to take effect.
Click on the Reboot button to reboot the system.
Click on the Toggle Help button to see a short description of
some of the web page items. First click on the Toggle Help
button, and you will see a question mark ( ) appear next to
some of the web page items. Move the mouse pointer to hover
over a question mark to see a short description of a specific web
page item.
Note
You must click on the Save button and then the Reboot button for the changes to take
effect.
2.3.9.1 Assigning Priority
The device will prioritize simultaneous audio streams according to their priority in the list.
If both SIP and Multicast is enabled, SIP audio streams are considered priority 4.5. SIP audio will
interrupt multicast streams with priority 0 through 4 and will be interrupted by multicast streams with
priority 5 through 9.
During priority 9 multicast streams, the volume is set to maximum.
Note
Ringtones and
Nightringtones
Operations Guide
SIP calls, multicast streams, ring tones, ringback tones, and nightring tones are all
prioritized.
Ringtones all play at the same priority level. This means that it is possible to have a nightring tone
and a normal ringtone playing at the same time.
931236H
CyberData Corporation
Installing the SIP Loudspeaker Amplifier (PoE) 60
SIP Loudspeaker Amplifier (PoE) Setup
2.3.10 Configure the Sensor Page Parameters
The door sensor (pins 1 and 2) on the terminal block can be used to monitor a door's open or closed
state. There is an option on the Sensor Page to trigger on an open or short condition on these pins.
The door sensor alarm will be activated when the Sensor Timeout (in seconds) parameter has
been met.
Each sensor can trigger up to five different actions:
•
Flash the LED until the sensor is deactivated (roughly 10 times/second)
•
Activate the relay until the sensor is deactivated
•
Loop an audio file out of the speaker until the sensor is deactivated
•
Call an extension and establish two way audio
•
Call an extension and play a pre-recorded audio file
Note
Calling a preset extension can be set up as a point-to-point call, but currently can't send
delayed DTMF tones.
1. Click Sensor menu button to open the Sensor Page (Figure 2-35).
Operations Guide
931236H
CyberData Corporation
Installing the SIP Loudspeaker Amplifier (PoE) 61
SIP Loudspeaker Amplifier (PoE) Setup
Figure 2-35. Sensor Page
Operations Guide
931236H
CyberData Corporation
Installing the SIP Loudspeaker Amplifier (PoE) 62
SIP Loudspeaker Amplifier (PoE) Setup
2. On the Sensor page, enter values for the parameters indicated in Table 2-21.
Note
The question mark icon ( ) in the following table shows which web page items will be defined
after the Toggle Help button is pressed.
Table 2-21. Sensor Page Parameters
Web Page Item
Description
Sensor Settings
Sensor Normally Closed
Select the inactive state of the sensor. The sensor is also known
as the Sense Input on the device's terminal block.
Sensor Timeout (in seconds)
The time (in seconds) the device will wait before it performs an
action when the on-board door sensor is activated. The action(s)
performed are based on the configured Sensor Settings below.
Enter up to 5 digits.
Activate Relay
When selected, the device's on-board relay will be activated until
the on-board sensor is deactivated.
Play Audio Locally
When selected, the device will loop an audio file out of the
speaker until the sensor is deactivated.
Make call to extension
When selected, the device will call an extension when the onboard door sensor is activated. Use the Dial Out Extension field
below to specify the extension the device will call.
Dial Out Extension
Specify the extension the device will call when the on-board
sensor is activated. Enter up to 64 alphanumeric characters.
Dial Out ID
An additional Caller identification string added to outbound calls.
Enter up to 64 alphanumeric characters.
Play recorded audio
When selected, the device will call the Dial Out Extension and
play an audio file to the phone answering the SIP call
(corresponds to Sensor Triggered on the Audiofiles Page
page).
Repeat Sensor Message
The number of times to repeat the audio message through the
local speaker or to the remote endpoint. A value of 0 will repeat
the message while the sensor is active. Enter a value from 065536.
Sensor Strobe Settings
Operations Guide
Blink Strobe on Sensor
When selected, the Strobe will blink a scene when the sensor is
triggered.
Scene
Select desired scene (only one may be chosen).
ADA Compliant
Strobe will blink ON at the specified brightness for 150ms then
OFF for 350ms during the duration of the event.
Slow Fade
Strobe will increase in brightness from 0 to the specified
brightness and back to 0 over the course of about 3.5 seconds
during the duration of the event.
Fast Fade
Strobe will increase in brightness from 0 to the specified
brightness and back to 0 over the course of about 1.5 seconds
during the duration of the event.
Slow Blink
Strobe will blink ON at the specified brightness for one second
then OFF for one second during the duration of the event.
931236H
CyberData Corporation
Installing the SIP Loudspeaker Amplifier (PoE) 63
SIP Loudspeaker Amplifier (PoE) Setup
Table 2-21. Sensor Page Parameters (continued)
Web Page Item
Description
Fast Blink
Strobe will blink ON at the specified brightness then OFF five
times per second during the duration of the event.
Color
Select desired color (only one may be chosen).
Brightness
How bright the strobe will blink when the sensor is triggered. This
is the maximum brightness for “fade” type scenes.
Red
The red LED value for Sensor.
Green
The green LED value for Sensor.
Blue
The blue LED value for Sensor.
Click the Test Sensor button to test the sensor.
Use this button to preview the strobe flashing behavior for the
Sensor Strobe Settings.
Click the Save button to save your configuration settings.
Note: You need to reboot for changes to take effect.
Click on the Reboot button to reboot the system.
Click on the Toggle Help button to see a short description of
some of the web page items. First click on the Toggle Help
button, and you will see a question mark ( ) appear next to
some of the web page items. Move the mouse pointer to hover
over a question mark to see a short description of a specific web
page item.
Note
Operations Guide
You must click on the Save button for the changes to take effect.
931236H
CyberData Corporation
Installing the SIP Loudspeaker Amplifier (PoE) 64
SIP Loudspeaker Amplifier (PoE) Setup
2.3.11 Configure the Audiofiles Page Parameters
The Audiofiles page is used to add custom audio to the board. User uploaded audio will take
precedence over the audio files shipped with the device.
1. Click on the Audiofiles menu button to open the Audiofiles page (Figure 2-36).
Figure 2-36. Audiofiles Page
Operations Guide
931236H
CyberData Corporation
Installing the SIP Loudspeaker Amplifier (PoE) 65
SIP Loudspeaker Amplifier (PoE) Setup
Figure 2-37. Audiofiles Page
Operations Guide
931236H
CyberData Corporation
Installing the SIP Loudspeaker Amplifier (PoE) 66
SIP Loudspeaker Amplifier (PoE) Setup
Figure 2-38. Audiofiles Page
Operations Guide
931236H
CyberData Corporation
Installing the SIP Loudspeaker Amplifier (PoE) 67
SIP Loudspeaker Amplifier (PoE) Setup
2. On the Audiofiles page, enter values for the parameters indicated in Table 2-22.
Note
The question mark icon ( ) in the following table shows which web page items will be defined
after the Toggle Help button is pressed.
Table 2-22. Audiofiles Page Parameters
Web Page Item
Description
Available Space
Shows the space available for the user to save custom audio files if they want to change the
message when the door or sensor is triggered.
Stored Messages
Stored Message 1 through 9
Stored Message 1 corresponds to the message played after pressing 1 on a phone keypad.
Stored Message 2 corresponds to the message played after pressing 2 on a phone keypad.
Stored Message 3 corresponds to the message played after pressing 3 on a phone keypad.
Stored Message 4 corresponds to the message played after pressing 4 on a phone keypad.
Stored Message 5 corresponds to the message played after pressing 5 on a phone keypad.
Stored Message 6 corresponds to the message played after pressing 6 on a phone keypad.
Stored Message 7 corresponds to the message played after pressing 7 on a phone keypad.
Stored Message 8 corresponds to the message played after pressing 8 on a phone keypad.
Stored Message 9 corresponds to the message played after pressing 9 on a phone keypad.
Audio Files
0-4
The name of the audio configuration option is the same as the spoken audio that plays on
the board (24 character limit).
'0' corresponds to the spoken word “zero.”
'1' corresponds to the spoken word “one.”
'2' corresponds to the spoken word “two.”
'3' corresponds to the spoken word “three.”
'4' corresponds to the spoken word “four.”
5-9
The name of the audio configuration option is the same as the spoken audio that plays on
the board (24 character limit).
'5' corresponds to the spoken word “five.”
'6' corresponds to the spoken word “six.”
'7' corresponds to the spoken word “seven.”
'8' corresponds to the spoken word “eight.”
'9' corresponds to the spoken word “nine.”
Dot
Corresponds to the spoken word “dot.” (24 character limit)
Audio Test
Corresponds to the message “This is the CyberData IP speaker test message...” (24
character limit)
Enter Code
Corresponds to the message “Enter Code” (24 character limit).
Invalid Code
Corresponds to the message “Invalid Code” (24 character limit).
Page Tone
Corresponds to a simple tone used for beep on initialization and beep on page (24 character
limit).
Your IP Address is
Corresponds to the message “Your IP address is...” (24 character limit).
Rebooting
Corresponds to the spoken word “Rebooting” (24 character limit).
Operations Guide
931236H
CyberData Corporation
Installing the SIP Loudspeaker Amplifier (PoE) 68
SIP Loudspeaker Amplifier (PoE) Setup
Table 2-22. Audiofiles Page Parameters (continued)
Web Page Item
Description
Restoring Default
Corresponds to the message “Restoring default” (24 character limit).
Ring Tone
This is the tone that plays when set to ring when receiving a call (24 character limit).
Sensor Triggered
Corresponds to the message “Sensor Triggered” (24 character limit).
Night Ring
Specifies the ringtone for nightring. By default this parameter uses the same audio file that is
selected for the Ring Tone parameter.
Menu Audio Files
Menu Audio Files are user-uploadable messages that create the audio menu played to the
caller.
Cancel
Corresponds to the word "Cancel" used in the audio menu played to the caller. (24 character
limit).
Currently Playing
Corresponds to the words "Currently Playing" used in the audio menu played to the caller.
(24 character limit).
Invalid Entry
Corresponds to the words "Invalid Entry" used in the audio menu played to the caller. (24
character limit).
Page
Corresponds to the word "Page" used in the audio menu played to the caller. (24 character
limit).
Play Stored Message
Corresponds to the words "Play Stored Message" used in the audio menu played to the
caller. (24 character limit).
Pound (#)
Corresponds to whatever word or phrase the user wishes to call the pound key in the audio
menu played to the caller (24 character limit).
Press
Corresponds to the word "Press" used in the audio menu played to the caller. (24 character
limit).
Stored Message
Corresponds to the words "Stored Message" used in the audio menu played to the caller.
(24 character limit).
Through
Corresponds to the word "Through" used in the audio menu played to the caller. (24
character limit).
To
Corresponds to the word "To" used in the audio menu played to the caller. (24 character
limit).
Click on the Browse button to navigate to and select an audio file.
The Play button will play that audio file.
The Delete button will delete any user uploaded audio and restore the stock audio file.
The Save button will download a new user audio file to the board once you've selected the
file by using the Browse button. The Save button will delete any pre-existing user-uploaded
audio files.
Operations Guide
931236H
CyberData Corporation
Installing the SIP Loudspeaker Amplifier (PoE) 69
SIP Loudspeaker Amplifier (PoE) Setup
2.3.11.1 User-created Audio Files
User created audio files should be saved in the following format:
RIFF (little-endian) data, WAVE audio, Microsoft PCM, 16 bit, mono 8000 Hz
You can use the free utility Audacity to convert audio files into this format. See Figure 2-39 through
Figure 2-41.
Figure 2-39. Audacity 1
Figure 2-40. Audacity 2
Operations Guide
931236H
CyberData Corporation
Installing the SIP Loudspeaker Amplifier (PoE) 70
SIP Loudspeaker Amplifier (PoE) Setup
When you export an audio file with Audacity, save the output as:
•
WAV (Microsoft) signed 16 bit PCM.
Figure 2-41. WAV (Microsoft) signed 16 bit PCM
WAV (Microsoft) signed 16 bit PCM
Operations Guide
931236H
CyberData Corporation
Installing the SIP Loudspeaker Amplifier (PoE) 71
SIP Loudspeaker Amplifier (PoE) Setup
2.3.12 Configure the Events Parameters
The Events page specifies a remote server that can be used to receive HTTP POST events when
actions take place on the board.
1. Click on the Events menu button to open the Events page (Figure 2-42).
Figure 2-42. Event Page
Operations Guide
931236H
CyberData Corporation
Installing the SIP Loudspeaker Amplifier (PoE) 72
SIP Loudspeaker Amplifier (PoE) Setup
2. On the Events page, enter values for the parameters indicated in Table 2-23.
Note
The question mark icon (
) in the following table shows which web page items will be defined
after the Toggle Help button is pressed.
Table 2-23. Events Page Parameters
Web Page Item
Description
Enable Event Generation
The device will send HTTP POST events to the specified remote
server and port number whenever a certain action takes place.
Select an event type below to generate an HTTP POST event.
Events
Enable Call Start Events
When selected, the device will report the start of a SIP call.
Enable Call Terminated Events
When selected, the device will report the end of a SIP call.
Enable Relay Activated Events
When selected, the device will report relay activation.
Enable Relay Deactivated Events
When selected, the device will report relay deactivation.
Enable Night Ring Events
When selected, the device will report when it starts ringing upon an
incoming SIP call to the Nightringer extension. As a reminder, the
Nightringer extension always rings upon an incoming SIP call and it
is not possible to alter this behavior.
Enable Power On Events
When selected, the device will report when it boots.
Enable Multicast Start Events
When selected, the device will report when the device starts playing
a multicast audio stream.
Enable Multicast Stop Events
When selected, the device will report when the device stops playing
a multicast audio stream.
Enable Sensor Events
When selected, the device will report when the on-board sensor is
activated.
Enable 60 Second Heartbeat Events
When enabled, the device will report a Heartbeat event every 60
seconds. SIP registration is not required to generate Heartbeat
events.
Check All
Click on Check All to select all of the events on the page.
Uncheck All
Click on Uncheck All to de-select all of the events on the page.
Event Server
Server IP Address
The IPv4 address of the event server in dotted decimal notation.
Server Port
Specify the event server port number. The supported range is 065536. Enter up to 5 digits.
Server URL
Generally, the destination URL is the name of the application that
receives the events and the string in the HTTP POST command. It
can be a script used to parse and process the HTTP POST events.
Enter up to 127 characters.
Click the Save button to save your configuration settings.
Note: You need to reboot for changes to take effect.
Click on the Reboot button to reboot the system.
Operations Guide
931236H
CyberData Corporation
Installing the SIP Loudspeaker Amplifier (PoE) 73
SIP Loudspeaker Amplifier (PoE) Setup
Table 2-23. Events Page Parameters(continued)
Web Page Item
Description
Click on the Toggle Help button to see a short description of some
of the web page items. First click on the Toggle Help button, and
you will see a question mark ( ) appear next to some of the web
page items. Move the mouse pointer to hover over a question mark
to see a short description of a specific web page item.
Note
Operations Guide
You must click on the Save button and then the Reboot button for the changes to take
effect.
931236H
CyberData Corporation
Installing the SIP Loudspeaker Amplifier (PoE) 74
SIP Loudspeaker Amplifier (PoE) Setup
2.3.12.1 Example Packets for Events
The server and port are used to point to the listening server and the 'Remote Event Server URL' is
the destination URL (typically the script running on the remote server that's used to parse and
process the POST events).
Note
The XML is URL-encoded before transmission so the following examples are not completely
accurate.
Here are example packets for every event:
POST xmlparse_engine HTTP/1.1
Host: 10.0.3.79
User-Agent: CyberData/1.0.0
Content-Length: 197
Content-Type: application/x-www-form-urlencoded
<?xml version="1.0" encoding="ISO-8859-1"?>
<cyberdata NAME='CyberData Device' MAC='0020f70015b6'>
<event>POWERON</event>
</cyberdata>
POST xmlparse_engine HTTP/1.1
Host: 10.0.3.79
User-Agent: CyberData/1.0.0
Content-Length: 199
Content-Type: application/x-www-form-urlencoded
<?xml version="1.0" encoding="ISO-8859-1"?>
<cyberdata NAME='CyberData Device' MAC='0020f70015b6'>
<event>HEARTBEAT</event>
</cyberdata>
POST xmlparse_engine HTTP/1.1
Host: 10.0.3.79
User-Agent: CyberData/1.0.0
Content-Length: 196
Content-Type: application/x-www-form-urlencoded
<?xml version="1.0" encoding="ISO-8859-1"?>
<cyberdata NAME='CyberData Device' MAC='0020f70015b6'>
<event>BUTTON</event>
</cyberdata>
POST xmlparse_engine HTTP/1.1
Host: 10.0.3.79
User-Agent: CyberData/1.0.0
Content-Length: 201
Content-Type: application/x-www-form-urlencoded
<?xml version="1.0" encoding="ISO-8859-1"?>
<cyberdata NAME='CyberData Device' MAC='0020f70015b6'>
<event>CALL_ACTIVE</event>
</cyberdata>
POST xmlparse_engine HTTP/1.1
Host: 10.0.3.79
Operations Guide
931236H
CyberData Corporation
Installing the SIP Loudspeaker Amplifier (PoE) 75
SIP Loudspeaker Amplifier (PoE) Setup
User-Agent: CyberData/1.0.0
Content-Length: 205
Content-Type: application/x-www-form-urlencoded
<?xml version="1.0" encoding="ISO-8859-1"?>
<cyberdata NAME='CyberData Device' MAC='0020f70015b6'>
<event>CALL_TERMINATED</event>
</cyberdata>
POST xmlparse_engine HTTP/1.1
Host: 10.0.3.79
User-Agent: CyberData/1.0.0
Content-Length: 197
Content-Type: application/x-www-form-urlencoded
<?xml version="1.0" encoding="ISO-8859-1"?>
<cyberdata NAME='CyberData Device' MAC='0020f70015b6'>
<event>RINGING</event>
</cyberdata>
POST xmlparse_engine HTTP/1.1
Host: 10.0.3.79
User-Agent: CyberData/1.0.0
Content-Length: 234
Content-Type: application/x-www-form-urlencoded
<?xml version="1.0" encoding="ISO-8859-1"?>
<cyberdata NAME='CyberData Device' MAC='0020f70015b6'>
<event>MULTICAST_START</event>
<index>8</index>
</cyberdata>
POST xmlparse_engine HTTP/1.1
Host: 10.0.3.79
User-Agent: CyberData/1.0.0
Content-Length: 233
Content-Type: application/x-www-form-urlencoded
<?xml version="1.0" encoding="ISO-8859-1"?>
<cyberdata NAME='CyberData Device' MAC='0020f70015b6'>
<event>MULTICAST_STOP</event>
<index>8</index>
</cyberdata>
POST xmlparse_engine HTTP/1.1
Host: 10.0.3.79
User-Agent: CyberData/1.0.0
Content-Length: 234
Content-Type: application/x-www-form-urlencoded
<?xml version="1.0" encoding="ISO-8859-1"?>
<cyberdata NAME='CyberData Device' MAC='0020f70015b6'>
<event>RELAY_ACTIVATED</event>
</cyberdata>
POST xmlparse_engine HTTP/1.1
Host: 10.0.3.79
Operations Guide
931236H
CyberData Corporation
Installing the SIP Loudspeaker Amplifier (PoE) 76
SIP Loudspeaker Amplifier (PoE) Setup
User-Agent: CyberData/1.0.0
Content-Length: 234
Content-Type: application/x-www-form-urlencoded
<?xml version="1.0" encoding="ISO-8859-1"?>
<cyberdata NAME='CyberData Device' MAC='0020f70015b6'>
<event>RELAY_DEACTIVATED</event>
</cyberdata>
POST xmlparse_engine HTTP/1.1
Host: 10.0.3.79
User-Agent: CyberData/1.0.0
Content-Length: 234
Content-Type: application/x-www-form-urlencoded
<?xml version="1.0" encoding="ISO-8859-1"?>
<cyberdata NAME='CyberData Device' MAC='0020f70015b6'>
<event>NIGHTRINGING</event>
</cyberdata>
Operations Guide
931236H
CyberData Corporation
Installing the SIP Loudspeaker Amplifier (PoE) 77
SIP Loudspeaker Amplifier (PoE) Setup
2.3.13 Configure the Autoprovisioning Parameters
Autoprovisioning can be used to automatically configure your device. The autoprovisioning file is an
xml file with the device configuration. Values found in this file will override values stored in on-board
memory.
Note
By default, the device will try to set up its configuration with autoprovisioning.
1. Click the Autoprov menu button to open the Autoprovisioning page. See Figure 2-43.
Figure 2-43. Autoprovisioning Page
Operations Guide
931236H
CyberData Corporation
Installing the SIP Loudspeaker Amplifier (PoE) 78
SIP Loudspeaker Amplifier (PoE) Setup
2. On the Autoprovisioning page, you may enter values for the parameters indicated in Table 224.
Note
The question mark icon ( ) in the following table shows which web page items will be defined
after the Toggle Help button is pressed.
Table 2-24. Autoprovisioning Page Parameters
Web Page Item
Description
Disable Autoprovisioning
Prevent the device from automatically trying to download a
configuration file. See Section 2.3.13.1, "Autoprovisioning" for
more information.
Autoprovisioning Server
Enter the IPv4 address of the provisioning server in dotted
decimal notation.
Autoprovisioning Filename
The autoprovisioning filename is the configuration filename.
The default autoprovisioning filename is in the format of
<mac address>.xml.
Supported filename extensions are .txt, and .xml. The current
filename is denoted by an asterisk at the bottom of the
Autoprovisioning Page. Enter up to 256 characters.
A file may have any name with an xml extension. If a file
name is entered, the device will look for the specified file
name, and only that file.
Use tftp
The device will use TFTP (instead of http) to download
autoprovisioning files.
Username
The username used to authenticate with an autoprovisioning
server. Leave this field blank to disable authentication.
Password
The password used to authenticate with an autoprovisioning
server. Leave this field blank to disable authentication.
Autoprovisioning Autoupdate 
(in minutes)
The reoccurring time (in minutes) the device will wait before
checking for new autoprovisioning files. Enter up to 6 digits. A
value of 0 will disable this option.
Note: To use the auto update options, enable the Set Time
with NTP Server on boot setting on the Device Page
page (see Table 2-11).
Autoprovision at time (HHMMSS)
The time of day the device will check for a new
autoprovisioning file. The time must be 6 characters in length
and in HHMMSS format. An empty value will disable this
option.
Note: To use the auto update options, enable the Set Time
with NTP Server on boot setting on the Device Page
page (see Table 2-11).
The idle time (in minutes greater than 10) after which the
device will check for a new autoprovisioning file. Enter up to 6
digits. A value of 0 will disable this option.
Autoprovision when idle
(in minutes > 10)
Note: To use the auto update options, enable the Set Time
with NTP Server on boot setting on the Device Page
page (see Table 2-11).
Click the Save button to save your configuration settings.
Note: You need to reboot for changes to take effect.
Operations Guide
931236H
CyberData Corporation
Installing the SIP Loudspeaker Amplifier (PoE) 79
SIP Loudspeaker Amplifier (PoE) Setup
Table 2-24. Autoprovisioning Page Parameters (continued)
Web Page Item
Description
Click on the Reboot button to reboot the system.
Click on the Toggle Help button to see a short description of
some of the web page items. First click on the Toggle Help
button, and you will see a question mark ( ) appear next to
some of the web page items. Move the mouse pointer to
hover over a question mark to see a short description of a
specific web page item.
Press the Download Template button to create an
autoprovisioning file for the device. See Section 2.3.13.3,
"Download Template Button"
Autoprovisioning log
Note
The autoprovisioning log provides information about the latest
autoprovisioning attempt (i.e. dhcp options and server
accessed and files parsed or not found).
You must click on the Save button and then the Reboot button for the changes to take
effect.
2.3.13.1 Autoprovisioning
On boot, the device will look for an autoprovisioning server configured on the Autoprovisioning Page
or specified as a DHCP option. When it finds a server, it will try to download the following (in order of
preference):
1. The file configured on the autoprovisioning page.
2. A file named according to it's mac address (for example: 0020f7350058.xml).
3. The file 000000cd.xml
The file can be hosted using a standard web server (like apache, IIS, or nginx), and the device can
download over SSL. The file server can be an ipv4 address in dotted decimal notation or a fully
qualified domain name.
By default, the device will get its autoprovisioning server from the DHCP options. See Section
2.3.13.2, "Sample dhcpd.conf" for an example of how to configure dhcpd to offer autoprovisioning
server addresses. If multiple options are set, the device will attempt to download autoprovisioning
files from every server.
The DHCP option determines the protocol used to download the autoprovisioning file. The device
looks for DHCP options in the following order:
1. Option 43 - a FQDN or an IP address to an http server
2. Option 72 - an IP address to an http server
3. Option 150 - an IP address to a tftp server
4. Option 66 - an IP address to a tftp server or if the entry starts with 'http', a FQDN to a http server.
Operations Guide
931236H
CyberData Corporation
Installing the SIP Loudspeaker Amplifier (PoE) 80
SIP Loudspeaker Amplifier (PoE) Setup
You can download an autoprovisioning template file from the Autoprovisioning Page using the
Download Template button (see Table 2-24). This file contains every configuration option that can
be set on the board.
Autoprovisioning files can contain the whole configuration or a subset of this file. The first
autoprovisioning file can also contain links to other autoprovisioning files.
The <MiscSettings> section contains some examples of additional autoprovisioning files:
<MiscSettings>
<DeviceName>CyberData Device</DeviceName>
<!-<AutoprovFile>common.xml</AutoprovFile>-->
<!-<AutoprovFile>sip_reg[macaddress].xml</AutoprovFile>-->
<!-<AutoprovFile>audio[macaddress]</AutoprovFile>-->
<!-<AutoprovFile>device[macaddress].xml</AutoprovFile>-->
</MiscSettings>
After downloading the first autoprovisioning file, the device will step through up to twenty additional
<AutoprovFile> entries and try to download these files from the same server.
When the device finds a filename with the string [macaddress], it will replace this string with the
mac address.
As an example, the user has configured option 43 on their DHCP server to “http://example.com,” and
on their server, they have a file named 0020f7123456.xml (the same as the mac address of the
device).
Operations Guide
931236H
CyberData Corporation
Installing the SIP Loudspeaker Amplifier (PoE) 81
SIP Loudspeaker Amplifier (PoE) Setup
The file 0020f7123456.xml contains:
<?xml version="1.0" encoding="utf-8" ?>
<specific>
<MiscSettings>
<DeviceName>Newname</DeviceName>
<AutoprovFile>common.xml</AutoprovFile>
<AutoprovFile>sip_reg[macaddress].xml</AutoprovFile>
<AutoprovFile>audio[macaddress]</AutoprovFile>
<AutoprovFile>device.xml</AutoprovFile>
</MiscSettings>
</specific>
1. The device will first set it's name to 'Newname'.
2. It will try to download http://example.com/common.xml.
3. It will try to download http://example.com/sip_reg0020f7123456.xml.
4. It will try to download http://example.com/audio0020f7123456.
5. It will try to download http://example.com/device.xml.
The device is reconfigured every time it downloads a new file so if two files configure the same
option the last one will be the one that is saved.
It is possible to autoprovision autoprovisioning values (for example, to disable autoprovisioning or to
configure a time to check for new files).
Checking for New The device will always check for an autoprovisioning files on boot but it can be configured to also
Autoprovisioning check after a periodic delay, when idle, or at a specified time. When one of these options is set, the
Files after Boot
device will download its autoprovisioning files again, and if it finds any differences from the files it
downloaded on boot, it will force a reboot and reconfigure.
Operations Guide
931236H
CyberData Corporation
Installing the SIP Loudspeaker Amplifier (PoE) 82
SIP Loudspeaker Amplifier (PoE) Setup
The
Autoprovisioning
Filename
The autoprovisioning filename can contain a file, a file path, or a directory.
Table 2-25. Autoprovisioning File Name
Autoprovisioning
Filename
Autoprovisioning
Server
File Downloaded
config.xml
10.0.1.3
10.0.1.3/config.xml
/path/to/config.xml
10.0.1.3
10.0.1.3/path/to/config.xml
subdirectory/path/
10.0.1.3
10.0.1.3/subdirectory/path/0020f7020002.xml
TFTP options may not support subdirectories. If a directory is set in the filename field, firmware and
audio files will also be downloaded from this subdirectory.
If the filename ends with a forward slash “/,” the device will treat it as a subdirectory.
For example:
The autoprovisioning server is set to “https://www.example.com”
The autoprovisioning filename is set to “cyberdata/”
On boot, the device will try to download:
https://www.example.com/cyberdata/0020f7123456.xml
...and if this fails:
https://www.example.com/cyberdata/000000cd.xml
Audio files and firmware files will also add “cyberdata” to the URL before downloading.
Operations Guide
931236H
CyberData Corporation
Installing the SIP Loudspeaker Amplifier (PoE) 83
SIP Loudspeaker Amplifier (PoE) Setup
Autoprovisioning <FirmwareSettings>
Firmware Updates
<FirmwareFile>505-uImage-ceilingspeaker</FirmwareFile>
<FirmwareServer>10.0.1.3</FirmwareServer>
<OutdoorIntercom30>firmware_file_v9.3.0</OutdoorIntercom30>
<OutdoorIntercom31>firmware_file_v10.3.0</OutdoorIntercom31>
<CallButton31>firmware_file_v10.3.0</CallButton31>
</FirmwareSettings>
In the <FirmwareSettings> section, the <FirmwareServer> element can be used to specify a
different server for hosting firmware files. When this element is not available, the device will try to
download the file from the autoprovisioning server.
The device will use the filename to determine when to autoprovision firmware updates. The default
configuration is blank, so the first time you set a value in your autoprovisioning file, it may force a
firmware update even if the firmware version has not changed.
The <FirmwareFile> name can contain path elements (i.e. /path/to/firmware/10.3.0-uImage[device_file_name]).
The device also supports product strings for downloading firmware. If the <FirmwareFile> option is
not set, the device will look for its particular product string for a firmware filename. In this way, a
generic autoprovisioning file can specify unique firmware for a range of products.
The list of valid product strings:
<ProductString>CallButton31</ProductString>
<ProductString>EmergencyIntercom31</ProductString>
<ProductString>EmergencyIntercom31SW</ProductString>
<ProductString>IndoorIntercom31</ProductString>
<ProductString>IndoorIntercom31SW</ProductString>
<ProductString>IndoorKeypad31</ProductString>
<ProductString>IndoorKeypad31SW</ProductString>
<ProductString>OfficeRinger31</ProductString>
<ProductString>OfficeRinger31SW</ProductString>
<ProductString>OutdoorIntercom31</ProductString>
<ProductString>OutdoorIntercom31SW</ProductString>
<ProductString>OutdoorKeypad31</ProductString>
<ProductString>OutdoorKeypad31SW</ProductString>
<ProductString>Strobe31</ProductString>
<ProductString>Strobe31SW</ProductString>
Operations Guide
931236H
CyberData Corporation
Installing the SIP Loudspeaker Amplifier (PoE) 84
SIP Loudspeaker Amplifier (PoE) Setup
Autoprovisioning
Example 1
Here's a simple example using four autoprovisioning files to configure two devices:
We boot up two devices with mac addresses 00:20:f7:02:00:01 and 00:20:f7:02:00:02 (Device1
and Device2).
The devices are set to use DHCP and that server provides an autoprovisioning server address with
option 43. The address is “https://autoprovtest.server.net.” The files on this server are as follows:
000000cd.xml
<MiscSettings>
<DeviceName>CyberData Autoprovisioned</DeviceName>
<AutoprovFile>sip_common.xml</AutoprovFile>
<AutoprovFile>sip_[macaddress].xml</AutoprovFile>
</MiscSettings>
sip_common.xml
<SIPSettings>
<SIPServer>10.0.0.253</SIPServer>
<RemoteSIPPort>5060</RemoteSIPPort>
</SIPSettings>
sip_0020f7020001.xml
<SIPSettings>
<SIPUserID>198</SIPUserID>
<SIPAuthPassword>ext198</SIPAuthPassword>
<DialoutExtension0>204</DialoutExtension0>
</SIPSettings>
sip_0020f7020002.xml
<SIPSettings>
<SIPUserID>500</SIPUserID>
<SIPAuthPassword>ext500</SIPAuthPassword>
<DialoutExtension0>555</DialoutExtension0>
</SIPSettings>
On boot, Device1 tries to fetch the file 0020f7023614.xml from “https://autoprovtest.server.net”. This
file is not available, so device1 then tries to fetch the file 000000cd.xml. This file exists, and Device1
parses the three elements.
1. Device1 changes its device name to CyberData Autoprovisioned.
2. Device1 finds an AutoprovFile element containing the filename sip_common.xml. The device
downloads sip_common.xml from “https://autoprovtest.server.net,” and imports this
configuration, setting the sip server to 10.0.0.253 and the remote port to 5060.3.
3. Device1 finds another AutoprovFile element containing the filename sip_[macaddress].xml.
The device replaces the [macaddress] with its own mac address value creating
sip_0020f7020001.xml, downloads this file from “https://autoprovtest.server.net,” and imports
this configuration. This sets the user ID to 198, the password to ext198, and the dialout
extension to 204. Device1 is now finished with autoprovisioning.
Operations Guide
931236H
CyberData Corporation
Installing the SIP Loudspeaker Amplifier (PoE) 85
SIP Loudspeaker Amplifier (PoE) Setup
Device2 goes through the same steps by setting its device name to CyberData Autoprovisioned,
its SIP server to 10.0.0.253, and its port to 5060. When Device2 “sees” sip_[macaddress].xml,
Device2 replaces it with its own mac address and downloads sip_0020f7020002.xml from
“https://autoprovtest.server.net.” Device2 sets the SIP User ID to 500, the password to ext500, and
the dialout extension to 555.
Autoprovisioning
Example 2
Here is another example of setting up your autoprovisioning files:
We boot up two devices with mac addresses 00:20:f7:02:00:01 and 00:20:f7:02:00:02 (Device1
and Device2) and boot them on a network with a DHCP server configured with an autoprovisioning
server at 10.0.1.3 on option 150. Our TFTP server has three files:
0020f7020001.xml
<MiscSettings>
<AutoprovFile>common_settings.xml</AutoprovFile>
</MiscSettings>
<SIPSettings>
<SIPUserID>198</SIPUserID>
<SIPAuthPassword>ext198</SIPAuthPassword>
<DialoutExtension0>204</DialoutExtension0>
</SIPSettings>
0020f7020002.xml
<MiscSettings>
<AutoprovFile>common_settings.xml</AutoprovFile>
</MiscSettings>
<SIPSettings>
<SIPUserID>500</SIPUserID>
<SIPAuthPassword>ext500</SIPAuthPassword>
<DialoutExtension0>555</DialoutExtension0>
</SIPSettings>
common_settings.xml
<MiscSettings>
<DeviceName>CyberData Autoprovisioned</DeviceName>
</MiscSettings>
<SIPSettings> <SIPServer>10.0.0.253</SIPServer>
<RemoteSIPPort>5060</RemoteSIPPort>
</SIPSettings>
1. On boot, Device1 downloads 0020f7020001.xml from 10.0.1.3 and imports these values. The SIP
User ID is 198, the password is ext198, and the dialout extension is 204.
2. Device1 then gets the filename common_settings.xml from the AutoprovFile element and
downloads this file from the TFTP server at 10.0.1.3. and imports these settings. The device name is
set to CyberData Autoprovisioned, the SIP server is set to 10.0.0.253, and the port is set to 5060.
Device2 does the same except it downloads 0020f7020002.xml on boot and imports these values
instead. The Sip User ID is 500, password is ext500, and dialout extension is 555. Device2 then
downloads the common_settings.xml file and imports those values. The device name is set to
CyberData Autoprovisioned, the SIP server is set to 10.0.0.253, and the port is set to 5060.
Operations Guide
931236H
CyberData Corporation
Installing the SIP Loudspeaker Amplifier (PoE) 86
SIP Loudspeaker Amplifier (PoE) Setup
XML Files
XML files can contain <AutoprovFile> elements. If multiple DHCP options are specified, the device
will try to download autoprovisioning files from each in turn. The device will only look for
<AutoprovFile> elements in the first file downloaded from each server. You can specify up to 20
<AutoprovFile> elements in the first autoprovisioning file.
There are numerous ways to change an element of the configuration(xml) file. Using sip ext as an
example, the extension can be changed:
Within the device-specific xml, i.e. [macaddress].xml, via the AutoprovFile
element:<SIPSettings>/<SIPExt>
From the device specific xml, a pointer to a sip_common file
From the device specific xml, a pointer to the device specific sip_[macaddress].xml
From the common file, a pointer to sip_common.xml
From the common file, a pointer to the device specific (sip_[macaddress].xml)
Autoprovisioned
Audio Files
Audio files are stored in non-volatile memory and an autoprovisioned audio file will only have to be
downloaded once for each device. Loading many audio files to the device from the web page could
cause it to appear unresponsive. If this happens, wait until the transfer is complete and then refresh
the page.
The device uses the file name to determine when to download a new audio file. This means that if
you used autoprovisioning to upload a file and then changed the contents of this file at the TFTP
server, the device will not recognize that the file has changed (because the file name is the same).
Since audio files are stored in non-volatile memory, if autoprovisioning is disabled after they have
been loaded to the board, the audio file settings will not change. You can force a change to the audio
files on the board by clicking Restore Default on the Audio page or by changing the
autoprovisioning file with “default” set as the file name.
Operations Guide
931236H
CyberData Corporation
Installing the SIP Loudspeaker Amplifier (PoE) 87
SIP Loudspeaker Amplifier (PoE) Setup
2.3.13.2 Sample dhcpd.conf
#
# Sample configuration file for ISC dhcpd for Debian
#
ddns-update-style none;
option domain-name "voiplab";
option domain-name-servers 10.0.0.252;
option option-150 code 150 = ip-address;
option ntp-servers north-america.pool.ntp.org;
option space VendorInfo;
option VendorInfo.text code 10 = { text };
authoritative;
log-facility local7;
subnet 10.0.0.0 netmask 255.0.0.0 {
max-lease-time 3600;
default-lease-time 3600;
option routers
option subnet-mask
10.0.0.1;
255.0.0.0;
option domain-name
option domain-name-servers
"voiplab";
10.0.0.252;
option time-offset
-8;
# Pacific Standard Time
#
option www-server
99.99.99.99;
#
#
option tftp-server-name
option tftp-server-name
"10.0.1.52";
"http://test.cyberdata.net";
# OPTION 66
# OPTION 66
#
option option-150
10.0.0.252;
# OPTION 150
# These two lines are needed for option 43
#
vendor-option-space VendorInfo;
#
option VendorInfo.text "http://test.cyberdata.net";
# OPTION 72
# OPTION 43
# OPTION 43
range 10.10.0.1 10.10.2.1; }
Operations Guide
931236H
CyberData Corporation
Installing the SIP Loudspeaker Amplifier (PoE) 88
SIP Loudspeaker Amplifier (PoE) Setup
2.3.13.3 Download Template Button
The Download Template button allows the user to generate, download, edit, and then store an
autoprovisioning template on the server that serves the autoprovisioning files for devices.
To generate an autoprovisioning template directly from the device, complete the following steps:
1. On the Autoprovisioning page, click on the Download Template button.
2. You will see a window prompting you to save a configuration file (.xml) to a location on your
computer (Figure 2-44). The configuration file is the basis for the default configuration settings
for your unit).
3. Choose a location to save the configuration file and click on OK. See Figure 2-44.
Figure 2-44. Configuration File
4. At this point, you can open and edit the autoprovisioning template to change the configuration
settings in the template for the unit.
5. You can then upload the autoprovisioning file to a TFTP or HTTP server where the file can be
loaded onto other devices.
Operations Guide
931236H
CyberData Corporation
Installing the SIP Loudspeaker Amplifier (PoE) 89
SIP Loudspeaker Amplifier (PoE) Setup
2.4 Upgrade the Firmware and Reboot the SIP
Loudspeaker Amplifier (PoE)
2.4.1 Downloading the Firmware
To download the firmware to your computer:
1. Download the latest firmware file from the Downloads tab at the following webpage:
http://www.cyberdata.net/voip/011405/
2. Unzip the firmware version file. This file may contain the following:
•
Firmware file
•
Release notes
3. Log in to the home page as instructed in Section 2.3.4, "Using the Toggle Help Button".
4. Click on the Firmware menu button to open the Firmware page. See Figure 2-45.
Caution
GENERAL ALERT
Equipment Hazard: CyberData strongly recommends that you first reboot the
device before attempting to upgrade the firmware of the device. See Section 2.4.2,
"Reboot the Device".
Figure 2-45. Firmware Page
CyberData Paging Amplifier
v11.6.4
5. Click on the Browse button, and then navigate to the location of the firmware file.
6. Select the firmware file.
7. Click on the Upload button.
Note
Operations Guide
Do not reboot the device after clicking on the Upload button.
931236H
CyberData Corporation
Installing the SIP Loudspeaker Amplifier (PoE) 90
SIP Loudspeaker Amplifier (PoE) Setup
Note
This starts the upgrade process. Once the SIP Loudspeaker Amplifier (PoE) has uploaded
the file, the Uploading Firmware countdown page appears, indicating that the firmware is
being written to flash. The SIP Loudspeaker Amplifier (PoE) will automatically reboot when
the upload is complete. When the countdown finishes, the Firmware page will refresh. The
uploaded firmware filename should be displayed in the system configuration (indicating a
successful upload and reboot).
8. Table 2-26 shows the web page items on the Firmware page.
Table 2-26. Firmware Parameters
Web Page Item
Description
Current Firmware Version
Shows the current firmware version.
Use the Browse button to navigate to the location of the
firmware file that you want to upload.
Click on the Upload button to automatically upload the selected
firmware and reboot the system.
Operations Guide
931236H
CyberData Corporation
Installing the SIP Loudspeaker Amplifier (PoE) 91
SIP Loudspeaker Amplifier (PoE) Setup
2.4.2 Reboot the Device
To reboot a SIP Loudspeaker Amplifier (PoE), log in to the web page as instructed in Section 2.3.5,
"Log in to the Home Page".
1. Click on the Reboot button on the Home page (Figure 2-46). A normal restart will occur.
Figure 2-46. Home Page
CyberData Paging Amplifier
405100001
v11.6.4
Reboot
Operations Guide
931236H
CyberData Corporation
Installing the SIP Loudspeaker Amplifier (PoE) 92
SIP Loudspeaker Amplifier (PoE) Setup
2.5 Command Interface
Some functions on the device can be activated using simple POST commands to the web interface.
The examples in Table 2-27 use the free unix utility, wget, but any program that can send http POST
commands to the device should work.
2.5.1 Command Interface Post Commands
Note
These commands require an authenticated session (a valid username and password to
work).
Table 2-27. Command Interface Post Commands
Device Action
HTTP Post Commanda
Trigger relay (for configured delay)
wget --user admin --password admin --auth-no-challenge --nocheck-certificate --quiet -O /dev/null "https://10.0.3.71/cgibin/command.cgi" --post-data "test_relay=yes"
Place call to extension (example: extension 130)
wget --user admin --password admin --auth-no-challenge --nocheck-certificate --quiet -O /dev/null "https://10.0.3.71/cgibin/command.cgi" --post-data "call=130"
Terminate active call
wget --user admin --password admin --auth-no-challenge --nocheck-certificate --quiet -O /dev/null "https://10.0.3.71/cgibin/command.cgi" --post-data "terminate=yes"
Force reboot
wget --user admin --password admin --auth-no-challenge --nocheck-certificate --quiet -O /dev/null "https://10.0.3.71/cgibin/command.cgi" --post-data "reboot=yes"
Test Audio button
wget --user admin --password admin --auth-no-challenge --nocheck-certificate --quiet -O /dev/null "https://10.0.3.71/cgibin/command.cgi" --post-data "test_audio=yes"
Announce IP address
wget --user admin --password admin --auth-no-challenge --nocheck-certificate --quiet -O /dev/null "https://10.0.3.71/cgibin/command.cgi" --post-data "speak_ip_address=yes"
Play the "0" audio file
wget --user admin --password admin --auth-no-challenge --nocheck-certificate --quiet -O /dev/null "https://10.0.3.71/cgibin/audiofiles.cgi" --post-data "play_0=yes"
Play the "1" audio file
wget --user admin --password admin --auth-no-challenge --nocheck-certificate --quiet -O /dev/null "https://10.0.3.71/cgibin/audiofiles.cgi" --post-data "play_1=yes"
Play the "2" audio file
wget --user admin --password admin --auth-no-challenge --nocheck-certificate --quiet -O /dev/null "https://10.0.3.71/cgibin/audiofiles.cgi" --post-data "play_2=yes"
Play the "3" audio file
wget --user admin --password admin --auth-no-challenge --nocheck-certificate --quiet -O /dev/null "https://10.0.3.71/cgibin/audiofiles.cgi" --post-data "play_3=yes"
Play the "4" audio file
wget --user admin --password admin --auth-no-challenge --nocheck-certificate --quiet -O /dev/null "https://10.0.3.71/cgibin/audiofiles.cgi" --post-data "play_4=yes"
Operations Guide
931236H
CyberData Corporation
Installing the SIP Loudspeaker Amplifier (PoE) 93
SIP Loudspeaker Amplifier (PoE) Setup
Table 2-27. Command Interface Post Commands (continued)
Device Action
HTTP Post Commanda
Play the "5" audio file
wget --user admin --password admin --auth-no-challenge --nocheck-certificate --quiet -O /dev/null "https://10.0.3.71/cgibin/audiofiles.cgi" --post-data "play_5=yes"
Play the "6" audio file
wget --user admin --password admin --auth-no-challenge --nocheck-certificate --quiet -O /dev/null "https://10.0.3.71/cgibin/audiofiles.cgi" --post-data "play_6=yes"
Play the "7" audio file
wget --user admin --password admin --auth-no-challenge --nocheck-certificate --quiet -O /dev/null "https://10.0.3.71/cgibin/audiofiles.cgi" --post-data "play_7=yes"
Play the "8" audio file
wget --user admin --password admin --auth-no-challenge --nocheck-certificate --quiet -O /dev/null "https://10.0.3.71/cgibin/audiofiles.cgi" --post-data "play_8=yes"
Play the "9" audio file
wget --user admin --password admin --auth-no-challenge --nocheck-certificate --quiet -O /dev/null "https://10.0.3.71/cgibin/audiofiles.cgi" --post-data "play_9=yes"
Play the "Dot" audio file
wget --user admin --password admin --auth-no-challenge --nocheck-certificate --quiet -O /dev/null "https://10.0.3.71/cgibin/audiofiles.cgi" --post-data "play_d=yes"
Play the "Audio Test" audio file (from Audio Config)
wget --user admin --password admin --auth-no-challenge --nocheck-certificate --quiet -O /dev/null "https://10.0.3.71/cgibin/audiofiles.cgi" --post-data "play_audiotest=yes"
Play the "Page Tone" audio file
wget --user admin --password admin --auth-no-challenge --nocheck-certificate --quiet -O /dev/null "https://10.0.3.71/cgibin/audiofiles.cgi" --post-data "play_pagetone=yes"
Play the "Your IP Address Is" audio file
wget --user admin --password admin --auth-no-challenge --nocheck-certificate --quiet -O /dev/null "https://10.0.3.71/cgibin/audiofiles.cgi" --post-data "play_youripaddressis=yes"
Play the "Rebooting" audio file
wget --user admin --password admin --auth-no-challenge --nocheck-certificate --quiet -O /dev/null "https://10.0.3.71/cgibin/audiofiles.cgi" --post-data "play_rebooting=yes"
Play the "Restoring Default" audio file
wget --user admin --password admin --auth-no-challenge --nocheck-certificate --quiet -O /dev/null "https://10.0.3.71/cgibin/audiofiles.cgi" --post-data "play_restoringdefault=yes"
Play the "Ringback tone" audio file
wget --user admin --password admin --auth-no-challenge --nocheck-certificate --quiet -O /dev/null "https://10.0.3.71/cgibin/audiofiles.cgi" --post-data "play_ringback=yes"
Play the "Ring tone" audio file
wget --user admin --password admin --auth-no-challenge --nocheck-certificate --quiet -O /dev/null "https://10.0.3.71/cgibin/audiofiles.cgi" --post-data "play_ringtone=yes"
Play the "Night Ring" audio file
wget --user admin --password admin --auth-no-challenge --nocheck-certificate --quiet -O /dev/null "https://10.0.3.71/cgibin/audiofiles.cgi" --post-data "play_nightring=yes"
Delete the "0" audio file
wget --user admin --password admin --auth-no-challenge --nocheck-certificate --quiet -O /dev/null "https://10.0.3.71/cgibin/audiofiles.cgi" --post-data "delete_0=yes"
Delete the "1" audio file
wget --user admin --password admin --auth-no-challenge --nocheck-certificate --quiet -O /dev/null "https://10.0.3.71/cgibin/audiofiles.cgi" --post-data "delete_1=yes"
Operations Guide
931236H
CyberData Corporation
Installing the SIP Loudspeaker Amplifier (PoE) 94
SIP Loudspeaker Amplifier (PoE) Setup
Table 2-27. Command Interface Post Commands (continued)
Device Action
HTTP Post Commanda
Delete the "2" audio file
wget --user admin --password admin --auth-no-challenge --nocheck-certificate --quiet -O /dev/null "https://10.0.3.71/cgibin/audiofiles.cgi" --post-data "delete_2=yes"
Delete the "3" audio file
wget --user admin --password admin --auth-no-challenge --nocheck-certificate --quiet -O /dev/null "https://10.0.3.71/cgibin/audiofiles.cgi" --post-data "delete_3=yes"
Delete the "4" audio file
wget --user admin --password admin --auth-no-challenge --nocheck-certificate --quiet -O /dev/null "https://10.0.3.71/cgibin/audiofiles.cgi" --post-data "delete_4=yes"
Delete the "5" audio file
wget --user admin --password admin --auth-no-challenge --nocheck-certificate --quiet -O /dev/null "https://10.0.3.71/cgibin/audiofiles.cgi" --post-data "delete_5=yes"
Delete the "6" audio file
wget --user admin --password admin --auth-no-challenge --nocheck-certificate --quiet -O /dev/null "https://10.0.3.71/cgibin/audiofiles.cgi" --post-data "delete_6=yes"
Delete the "7" audio file
wget --user admin --password admin --auth-no-challenge --nocheck-certificate --quiet -O /dev/null "https://10.0.3.71/cgibin/audiofiles.cgi" --post-data "delete_7=yes"
Delete the "8" audio file
wget --user admin --password admin --auth-no-challenge --nocheck-certificate --quiet -O /dev/null "https://10.0.3.71/cgibin/audiofiles.cgi" --post-data "delete_8=yes"
Delete the "9" audio file
wget --user admin --password admin --auth-no-challenge --nocheck-certificate --quiet -O /dev/null "https://10.0.3.71/cgibin/audiofiles.cgi" --post-data "delete_9=yes"
Delete the "Audio Test" audio file
wget --user admin --password admin --auth-no-challenge --nocheck-certificate --quiet -O /dev/null "https://10.0.3.71/cgibin/audiofiles.cgi" --post-data "delete_audiotest=yes"
Delete the "Page Tone" audio file
wget --user admin --password admin --auth-no-challenge --nocheck-certificate --quiet -O /dev/null "https://10.0.3.71/cgibin/audiofiles.cgi" --post-data "delete_pagetone=yes"
Delete the "Your IP Address Is" audio file
wget --user admin --password admin --auth-no-challenge --nocheck-certificate --quiet -O /dev/null "https://10.0.3.71/cgibin/audiofiles.cgi" --post-data "delete_youripaddressis=yes"
Delete the "Rebooting" audio file
wget --user admin --password admin --auth-no-challenge --nocheck-certificate --quiet -O /dev/null "https://10.0.3.71/cgibin/audiofiles.cgi" --post-data "delete_rebooting=yes"
Delete the "Restoring Default" audio file
wget --user admin --password admin --auth-no-challenge --nocheck-certificate --quiet -O /dev/null "https://10.0.3.71/cgibin/audiofiles.cgi" --post-data "delete_restoringdefault=yes"
Delete the "Ringback tone" audio file
wget --user admin --password admin --auth-no-challenge --nocheck-certificate --quiet -O /dev/null "https://10.0.3.71/cgibin/audiofiles.cgi" --post-data "delete_ringback=yes"
Delete the "Ring tone" audio file
wget --user admin --password admin --auth-no-challenge --nocheck-certificate --quiet -O /dev/null "https://10.0.3.71/cgibin/audiofiles.cgi" --post-data "delete_ringtone=yes"
Delete the "Night Ring" audio file
wget --user admin --password admin --auth-no-challenge --nocheck-certificate --quiet -O /dev/null "https://10.0.3.71/cgibin/audiofiles.cgi" --post-data "delete_nightring=yes"
Operations Guide
931236H
CyberData Corporation
Installing the SIP Loudspeaker Amplifier (PoE) 95
SIP Loudspeaker Amplifier (PoE) Setup
Table 2-27. Command Interface Post Commands (continued)
Device Action
HTTP Post Commanda
Trigger the Door Sensor Test (Sensor Config page)
wget --user admin --password admin --auth-no-challenge --nocheck-certificate --quiet -O /dev/null "https://10.0.3.71/cgibin/sensor.cgi" --post-data "doortest=yes"
a.Type and enter all of each http POST command on one line.
Operations Guide
931236H
CyberData Corporation
96
Appendix A: Mounting the Amplifier
A.1 Mount the Amplifier
Before you mount the enclosure, make sure that you have received all of the parts for each
enclosure. Refer to Table A-1.
Table A-1. Wall Mounting Components (Part of the Accessory Kit)
Quantity
Part Name
1
Mounting Accessory Kit which includes:
Illustration
(3) #8 Plastic Anchors
(3) #8 x 1-1/4" Pan Head Phillips Self-Tapping Screws
151147
#8x1.25" Truss Head Phillips
Sheet Metal Screw (3x)
531032
Plastic Ribbed Anchor (3x)
Operations Guide
Note
The SIP Loudspeaker Amplifier (PoE) was designed for indoor use. Mounting it on the
external part of a building will require additional hardware for weatherproofing, cabling
access, and lightning suppression. Consult a certified electrician for details.
Note
For mounting, use the three #8 SHEET METAL SCREWS to secure the enclosure.
931236H
CyberData Corporation
97
Mount the Amplifier
A.1.1 Mounting the Enclosure
To mount the enclosure:
1. Prepare holes for the screws.
2. Plug in the power adapter and use the Power (PWR) LED to verify that the power is on.
3. Plug the ethernet cable into the device. The Link/Activity (Link/Act.) LED verifies the network
connection.
4. For wall mounting, use the three #8 x 1-1/4-inch Truss Head Phillip screws to secure the
speaker. See Figure A-1.
Figure A-1. Mounting the Enclosure
151147
#8x1.25" Truss Head Phillips
Sheet Metal Screw (3x)
531032
Plastic Ribbed Anchor (3x)
Operations Guide
931236H
CyberData Corporation
98
Appendix B: Setting up a TFTP Server
B.1 Set up a TFTP Server
Autoprovisioning requires a TFTP server for hosting the configuration file.
B.1.1 In a LINUX Environment
To set up a TFTP server on LINUX:
1. Create a directory dedicated to the TFTP server, and move the files to be uploaded to that
directory.
2. Run the following command where /tftpboot/ is the path to the directory you created in
Step 1: the directory that contains the files to be uploaded. For example:
in.tftpd -l -s /tftpboot/your_directory_name
B.1.2 In a Windows Environment
You can find several options online for setting up a Windows TFTP server. This example explains
how to use the Solarwinds freeware TFTP server, which you can download at:
http://www.cyberdata.net/support/voip/solarwinds.html
To set up a TFTP server on Windows:
1. Install and start the software.
2. Select File/Configure/Security tab/Transmit Only.
3. Make a note of the default directory name, and then move the firmware files to be uploaded to
that directory.
Operations Guide
931236H
CyberData Corporation
99
Appendix C: Troubleshooting/Technical
Support
C.1 Frequently Asked Questions (FAQ)
To see a list of frequently asked questions for your product, click on the FAQs tab at the following
webpage:
http://www.cyberdata.net/voip/011405/
C.2 Documentation
The documentation for this product is released in an English language version only.
To download PDF copies of CyberData product documentation, click on the Downloads tab at the
following webpage:
http://www.cyberdata.net/voip/011405/
Operations Guide
931236H
CyberData Corporation
100
Contact Information
C.3 Contact Information
Contact
CyberData Corporation
3 Justin Court
Monterey, CA 93940 USA
www.CyberData.net
Phone: 800-CYBERDATA (800-292-3732)
Fax: 831-373-4193
Sales
Sales 831-373-2601, Extension 334
Technical 
Support
The fastest way to get technical support for your VoIP product is to submit a VoIP Technical
Support form at the following website:
http://support.cyberdata.net/
The Support Form initiates a ticket which CyberData uses for tracking customer requests. Most
importantly, the Support Form tells us which PBX system and software version that you are
using, the make and model of the switch, and other important information. This information is
essential for troubleshooting. Please also include as much detail as possible in the Comments
section of the Support Form.
Phone: (831) 373-2601, Extension 333
C.4 Warranty and RMA Information
The most recent warranty and RMA information is available at the following website address:
http://support.cyberdata.net/
Operations Guide
931236H
CyberData Corporation
101
Index
boost (volume) 38
Symbols
#6 sheet metal screws 96
C
cabling 21
changing
the web access password 37
Cisco SRST 48
command interface 92
commands 92
components 11
configurable parameters 48
configuration
audio 64
default IP settings 27
door sensor 60
intrusion sensor 60
network 44
SIP 47
configuration home page 33
connecting the amplified outputs 12
connection options 15
connections 11, 15
connections inside of the NEMA box 11
contact information 100
contact information for CyberData 100
current network settings 45
CyberData contact information 100
Numerics
1 speaker configuration 12, 13, 14
16 gauge wire 12, 13, 14
2 speaker configuration 14
802.3af mode 12, 13, 14
802.3at compliance switch 12, 13, 14
802.3at mode 14
802.3at power injector (high power mode) 12, 13, 14
A
accessory kit 8, 96
activate relay (door sensor) 62
activity LED 22
address, configuration login 33
amplified outputs 12, 13, 14
high power mode 14
how to use and connect 12
low power mode 12, 13
announcing an IP address 23
audio configuration 64
night ring tone parameter 68
audio encodings 4
audio files, user-created 69
audio page 64
audio test 23
autoprovision at time (HHMMSS) 78
autoprovision when idle (in minutes > 10) 78
autoprovisioning 79
download template button 79
autoprovisioning autoupdate (in minutes) 78
autoprovisioning configuration 77, 78
autoprovisioning filename 78
autoprovisioning server (IP Address) 78
D
default
gateway 9, 27
IP address 9, 27
subnet mask 9, 27
username and password 9, 27
web login username and password 33
default gateway 9, 27, 45
default IP settings 27
default login address 33
device configuration 37
device configuration page 37
device configuration parameters 38
device configuration password
changing for web configuration access 37
DHCP Client 4
dial out extension (door sensor) 62
dial out extension strings 53
B
backup SIP server 1 48
backup SIP server 2 48
backup SIP servers, SIP server
backups 48
Operations Guide
931236H
CyberData Corporation
102
I
dial-out extension strings 55
dimensions 5
disable volume control dial 38
discovery utility program 33
distortion, total harmonic 5
DNS server 45
door sensor 60, 68
activate relay 62
dial out extension 62
door sensor normally closed 62
play audio locally 62
download autoprovisioning template button 79
DTMF tones 53, 55
DTMF tones (using rfc2833) 53
identifier names (PST, EDT, IST, MUT) 42
identifying your product 1
illustration of amplifier mounting process 96
import settings 35
import/export settings 35
input specifications 5
installation 2
IP address 9, 27, 45
IP address announcement 23
IP address confirmation 23
IP addressing
default
IP addressing setting 9, 27
E
J
enable night ring events 72
enclosure, mounting 96
ethernet I/F 5
event configuration
enable night ring events 72
expiration time for SIP server lease 49, 51
export settings 35
jumper descriptions 20
jumper locations 20
L
lease, SIP server expiration time 49, 51
LEDs 22
lengthy pages 59
line input specifications 5
line output specifications 5
Linux, setting up a TFTP server on 98
local SIP port 49
log in address 33
loudspeaker type 21
loudspeaker, cabling/wiring 21
low power mode (amplified outputs) 12, 13
F
factory defaults 10, 23
firmware
where to get the latest firmware 89
G
get autoprovisioning template 79
GMT table 42
GMT time 42
M
maximum wire length for two speaker configuration 14
MGROUP
MGROUP Name 58
mounting an amplifier 96
multicast configuration 56, 64
Multicast IP Address 58
H
harmonic distortion 5
hazard levels 4
high power mode (amplified outputs) 14
home page 33
http POST command 92
http web-based configuration 4
N
navigation (web page) 28
navigation table 28
Operations Guide
931236H
CyberData Corporation
103
NEMA box components 11
network configuration 44
network link activity, verifying 22
nightring tones 59
Nightringer 88
nightringer settings 50
NTP server 38
typical system installation 2
product specifications 5
protocols supported 4
R
one speaker configuration 12, 13, 14
optional two speaker configuration 14
output impedance 5
output level 5
output signal amplitudes 5
output specifications 5
reboot 90, 91
remote SIP port 49
reset test function management switch 23
resetting the IP address to the default 96
restoring the factory defaults 10, 23
ringtones 59
lengthy pages 59
rport discovery setting, disabling 49
RTFM switch 10, 23
RTP/AVP 4
P
S
packet time 4
pages (lengthy) 59
parts list 8
password
for SIP server login 48
login 33
restoring the default 9, 27
payload types 5
play audio locally (door sensor) 62
point-to-point configuration 54
polycom default channel 59
polycom emergency channel 59
polycom priority channel 59
port
local SIP 49
remote SIP 49
posix timezone string
timezone string 38
POST command 92
power input 5
power LED 10, 22
power, connecting to paging amplifier 12
priority
assigning 59
product
mounting 96
parts list 8
product features 3
product overview
product features 3
product specifications 5
supported protocols 4
supported SIP servers 4
safety instructions 5
sales 100
sensor
sensor normally closed 62
sensor timeout 62
sensor connection 16
sensor setup page 61
sensor setup parameters 60
sensors 62
server address, SIP 48
service 100
set time with external NTP server on boot 38
SIP
enable SIP operation 48
local SIP port 49
user ID 48
SIP (session initiation protocol) 4
SIP configuration 47
SIP configuration parameters
outbound proxy 49, 51
registration and expiration, SIP server lease 49, 51
unregister on reboot 49
user ID, SIP 48
SIP registration 48
SIP remote SIP port 49
SIP server 48
password for login 48
SIP servers supported 4
unregister from 49
user ID for login 48
SIP server configuration 48
SIP volume 38
speaker cable 21
O
Operations Guide
931236H
CyberData Corporation
104
W
speaker configuration 12, 13, 14
speaker configuration for two speakers 14
speaker wire 21
SRST 48
standard 1 speaker configuration 12, 13, 14
status LED 10, 22
subnet mask 9, 27, 45
supported protocols 4
warranty policy at CyberData 100
web access password 9, 27
web access username 9, 27
web configuration log in address 33
web page
navigation 28
web page navigation 28
wget, free unix utility 92
Windows, setting up a TFTP server on 98
wire gauge 12, 13, 14
wire length going to wire nuts for two speaker
configuration 14
wire nuts to connect wire 12, 13, 14
wiring 21
T
tech support 100
technical support, contact information 100
test audio 23
TFTP server 4, 98
time zone string examples 42
two speaker configuration 14
U
user ID
for SIP server login 48
username
changing for web configuration access 37
default for web configuration access 33
restoring the default 9, 27
using the amplified outputs 12
V
verifying
network link and activity 22
power on 22
VLAN ID 45
VLAN Priority 45
VLAN tagging support 45
VLAN tags 45
volume 26
multicast volume 38
ring volume 38
sensor volume 38
SIP volume 38
volume adjustment 24
volume boost 38
volume control dial
disable 38
volume dial 25, 26
Operations Guide
931236H
CyberData Corporation