https://theterrapi.com
copyright 2020-2022 INUX3D®
theterrapi.com
Model:X
M3x6
M3x6
Power Button
M3x6
M3x10 w/PB*
M2.5x16
Power Button
holder
SSD
M2.5x16
Bottom View
Fan Bolts*
M3x6
40mm FAN
Top
SSD Clip
M2.5x16
Assembly Material
6x M3x6mm (for SSD)
4x M2.5x16mm (for fan hat)
With Power Button (optional)
1x M3x10mm
Bottom
SSD Clip
Fan Bolts
M2.5x16
Raspberry Pi
Base Front
Dept.
Technical reference
Created by
Design
Drawing
LL
https://shop.inux3d.com
sales@inux3d.com
No FAN (optional)
4x M2.5x6mm
(instead of M2.5x16mm)
1x 40x40x10mm Fan 5v
1x INUX3D Power button
1x M2 Grub screw (power button)
Approved by
4/15/2022 LL
15/4/2022
Document type
Document status
COMPONENTS
FINAL
Title
DWG No.
TerraPi X
Parts & Assembly
7
Rev.
Date of issue
1 15/4/2022
Sheet
1/2
16.89 [0.66]
107.11 [4.22]
14.10 [0.56]
40.00 [1.57]
69.71 [2.74]
80.93 [3.19]
84.55 [3.33]
11.40 [0.45]
56.00 [2.2]
94.00 [3.7]
100.00 [3.94]
38.13 [1.5]
7.20 [0.28]
Units in mm [inch]
9.16 [0.36]
9.38 [0.37]
26.96 [1.06]
41.20 [1.62]
47.20 [1.86]
Dept.
Technical reference
Created by
Design
Drawing
LL
Approved by
4/15/2022 LL
15/4/2022
Document type
Document status
DIMENSIONS
FINAL
Title
DWG No.
TerraPi X
Parts & Assembly
7
Rev.
Date of issue
1 15/4/2022
Sheet
2/2
Assembly Instructions Single SSD TerraPi X
Front
M3x6mm
Place the drive on a flat surface and mount the
SSD clips as shown above. Use M3x6mm
screws to secure the SSD mounting clips.
Please pay attention to the orientation.
A
SSD Mounting
Clips
Mount the FAN on the
Fan Hat FIRST
M3x12mm*
M3x16mm
After mounting the fan, place the Pi and align
it over the mounting holes. Then, place the
M2.5x16mm
fan hat and align it as well. Use the
M2.5x16mm screws to secure it.
M2.5x16mm
B
PLEASE DO NOT O ERTI HTEN
The M2.5x16mm screws are self tapping
M3x12mm*
FAN Hat
C
Finally, use the M3x6mm screws to attach the
base of the Terrapi on to the SSD drive.
If you do not plan to use a fan, then instead of
placing the fan hat, secure the board on the
SSD mounting clips by the 4x M2.5x6mm
screws supplied in a separate bag.
M3x6mm
Bill of Assembly Materials
TerraPi Single SSD: 6pcs M3x6, 4pcs M2.5x16, 4pcs M2.5x6
* M3x12 is only for the INUX3D Fan (also for TerraPi SE)
Colors: RED, BLACK, BLUE, For SE Orange/Black
Dept.
Technical reference
Created by
TECH
M2.5
LL
https://shop.inux3d.com
sales@inux3d.com
Approved by
12/13/2020 LL
12/12/2020
Document type
Document status
Assembly
FINAL
Title
DWG No.
TerraPi v5
M2.5 version
4
Rev.
Date of issue
C 20201213
Sheet
1/1