@poo/send
Pool Bond PB-2008 Water Bonding Fitting
Follow these Important Safety Instructions
LISTED
40YZ
ELECTRICRL POOL BoNDING
.
®
Part Number
PB-2008
680.26(c)
Step 1 Components
®
LISTED
A. PoolBond Casting Part Number PB-2008 with 1" NPT Pipe Thread.
B. Split Bolt Connector, UL rated for Direct Burial.
C. Solid #8 Copper wire, not supplied.
40YZ
Step 2 Fitti ng Orientation
• Install in Pool Plumbing using a Plumbing Tee.
• Always install the Poolbond Tee with the fitting
in horizontal or vertically down orientation to
avoid trapped air in pool plumbing.
Step 3 Where to Install
a
Horizontal
All Installations
Vertical Down
Above Ground Pools
/[0
(-f·_······· ~t.I ...
i
,-
I
L;'
~-) 'I •.."
I
j
In-Ground Pools
Above Ground Pools
Ground
BondingW ..
to Grid
Perma-Oast Company
1871 Aspen Circle
Pueblo, Colorado 81006
Step 4 Installing PoolBond
• First, install the male threaded fitting in the threaded tee (dry fit) until
the fitting just starts to tighten on the threaded tee. Count the number
of turns it takes. Document this number and disengage the two parts.
• Apply thread sealant. Use Plumber Pipe Dope or Teflon Paste, do not use
Teflon Tape.
• Reassemble the two parts using the number of turns recorded in th
first step and tighten two more turns. Do not overtighten to avoid da aging
plastic pipe.
[!]r
[!]
rSOC)(2' soc); l<rll'T
Of!
~ 1iTSOCx l·1/2"SOC)( rru-r
RECOMMENDED
In!1t.~ll.i)flordor
',L'r Of 2' f'1~
NOT RECOMMENDED
www.permacastonline.com
Revision 8/6114
- PERMA-CAST
FEATURED PRODUCTS
SWimrnJ,,9 Pool Paxiucts
1871 As-penCircle· Pueblo, Colorado 81006 e Phone 719-544-9544
TECHNClCE
Water Bonding Specifications
SALT POOL ANOCES~
~t6
ANODEAREA
24 SQUAREINCHES
.5 POUNDZINC
VENTED FOR
VERTICAL INSTALLATION
0,/
1:
ANODEAREA
54 SQUAREINCHES
I
1.4 POUNDZINC
VENTED FOR
•
VERTICAL INSTALLATION
The 2008 National Electrical Code (NEC) recquires that a!1intentional electrical
bond of a minimum conductive surface area of 9 square Inches be Installed In
contact with the swimming pool water. This requirement is spelled out in
Section 680.26(C). PooIBOndPB-2008 meets the specifications spelled out by the NEe.
-'--I
I
..
I'
1" INLINE
ElECTRICRL
SONDING
®
LISTED
.....
40VZ
®
ABOVEGROUND
PB·AG
Inside Fac,e:]
PLUMBING KITS
ie.,
t\
i·
.420
-T
Surf~c; Are~ Right Triangle
1.75 .5 .035 - .031
.674*6 Sides = 4.044
.031*12 Sides = .372
Total
PB-2008 ",.,
Inside Top Face
PB-2008
ie.,
1
I
.350
..
-i
(]
175
1--,-,1
.606
--1 f---I
ABOVEGROUNDKIT
08KIT·AG
:: 4.416
Inside Top Face
Surface Area Rectangle
.35*.606= .2121
Surface Area Triangle
.606*.5*.175= .053
.674* 1Sides = .2121
.031' 2 Sides = .053
Total
•
= 4.6794
Inside Face
Surface Area Rectangle
(.5*1.75)*(.35+.42)= .674
Lr-1.750~1
,35~
.7275*6Sides = 4.365
.0262"12Sides= .3164
'Total
®
';/1:
..
----1-
TN-IL-20
Poo/Send
POOL
SKIMMERMOUNT
1-1/2" PB2008-SK·15
2" PB·2008-SK20
Su~a<;eAr~a Right Triangle
.520 1.5 .5 .035 - .0262
Outside Face
I
2" INLINE
TN-IL
Outside Face
Surface Area Rectangle
(.5*1.5)"(.45+.52) = .7275
~==9i ____l
,J~_i-__
.450
Licensee P'o-:,Iuct
US Pn:c--rt i(-:i~;~)116H~
r---',
!
I
,
1.500
= .2651
Note: Area for Filletsand outside face not shown
However total surface area is an additional 1.29Sq. In
1-1/2" IN GROUNDKIT
08KIT-15
2" IN GROUNDKIT
08KIT-20
Perma-Cast Co.
www.permacastonline.com
Call BOO-74B-2770 for Technical Questions
Outside Face = 4.679
Inside Face = 4.416
In. Top Face = .265
See Note
= 1.290
Total Sq In. = 10.65 Sa. In.
Penna-Cast Company
www.permacastonline.com
call800-748-2770 for Technical Questions
Revised 212015