Technical Data
CSM-1901
Bedside Monitor
TD. CSM-1900_B
This technical data may be revised or replaced by Nihon Kohden at any time without notice.
Some products may not be available in your country.
1
FEATURES
Intended Use
Life Scope G9 is intended for continuous
monitoring, recording, and alarming of multiple
physiological parameters of adults, pediatrics
and neonates in the OR, recovery room, ICU,
CCU, HCU, NICU, ER, ward and other areas.
Main Components
Core unit, CU-191R and CU-192R
The fan-less core unit has a built-in PC. The PC
can provide lab data, X-ray data and medical
charts through a web browser.
• CU-191R: Intel Celeron 1.6 GHz
• CU-192R: Intel Core i7 1.5 GHz
Display
Display size is selectable and up to up to three
displays can be connected. (A third display
requires an optional YS-104P5 display
expansion board.) Each monitor can have a
different layout.
The VL-190P display unit has an alarm indicator
which shows the alarm severity in 3 levels.
Input unit, AY-600 series
Several types of input unit are available. See the
chart on the next page.
Data acquisition unit (DAU)
The data acquisition unit connects an input unit
or Life Scope PT transport monitor to the Life
Scope G9 monitor.
• JA-690PA: DAU without MULTI connector
• JA-694PA: DAU with 4 MULTI connectors
Transport function
Life Scope G9 supports transport. Patient
information and review data can be transferred
to another bed by disconnecting the input unit
from the source monitor and connecting it to the
destination monitor. (Transport function requires
an optional QM-600P memory unit in the input
unit.)
A Life Scope PT BSM-1700 series transport
monitor can also be used as an input unit for the
Life Scope G9 bedside monitor.
After connecting the input unit to the destination
bedside monitor in the network, the data in the
input unit is automatically transferred to the
bedside monitor and central monitor. All patient
information, including trend and waveforms, is
automatically transferred to maintain one
seamless patient record.
Smart cables and MULTI connectors
Smart cable technology lets you measure
different parameters without the need for
dedicated modules. When you plug a smart
cable into a MULTI connector, the monitor
automatically detects the type of parameter and
starts measuring.
Basic parameters of ECG, respiration, SpO 2 ,
NIBP and temperature can be measured with
dedicated connectors. Other parameters can be
measured with MULTI connectors. Up to 15
MULTI connectors for smart cable can be
configured.
Multilink connectors
A multilink connector receives data from an
external device such as an anesthesia machine
or ventilator and the monitor displays the
external device data with other monitoring data.
Number of Multilink connectors:
• CU-191R/CU-192R core unit: 3
• JA-690PA/JA-694PA DAU: 2
• JA-920P interface unit: 6
User Interface
Operation
Life Scope G9 can be operated by touch screen,
mouse, keyboard, remote control and bar code
scanner as well as by hard keys on the VL-190P
display unit and data acquisition unit.
Touch screen operation
The touch screen provides intuitive operation.
Drag and drop screen builder
You can change the screen position of numeric
values and waveforms by dragging and dropping
the numeric values.
Review while monitoring
The G-Scope function lets you review past data
without hiding the current vital signs and
waveforms. Just flick the side or bottom of the
screen to access three review windows.
Wireless remote control
You can operate Life Scope G9 by an RY-910PA
wireless remote control. The remote control has
six function keys to call up preset windows.
One remote control can operate up to 9 monitors
by changing the channel.
Alarm indicator receives the IR signals from the
RY-910PA. To use RY-910PA, alarm indicator
YL-920P or VL-190P display unit with alarm
indicator is required.
Nihon Kohden's networking technology enables
seamless monitoring across different central
monitors. You can see continuous past data
even from a different central monitor at a
different site.
2
Input units
Name
Input
unit
Smart
unit
Model
SpO2
Image
MULTI
Connector
Parameters
No. of MULTI
Connector
Basic
Parameters
AY-660P
NK
1
IBP, CO2
ECG (3/6 lead)
Resp (impedance)
SpO2
NIBP
Temp
AY-661P
NK
1
IBP, CO2,
ECG (3/6/12 lead)
Resp (impedance)
SpO2
NIBP
Dual Temp
ECG/BP Out
AY-651P
Nellcor
AY-631P
Masimo
AY-663P
NK
AY-653P
Nellcor
AY-633P
Masimo
AA-672P
-
Temp, CO, FiO2,
Resp (thermistor),
3
2
APCO, BIS,
2nd SpO2
IBP, CO2,
-
Temp, CO, FiO2,
Resp (thermistor),
AA-674P
-
4
APCO, BIS,
2nd SpO2
JA-694P
-
4
IBP, CO2,
-
Temp, CO, FiO2,
Resp (thermistor),
APCO, BIS,
2nd SpO2
DAU
Multi
amp
unit
Bedsi
de
monit
or
JA-690PA
-
0
-
-
AA-910P
-
4
IBP, CO2,
-
Temp, CO, FiO2,
Resp (thermistor)
BSM1763
NK
BSM1753
Nellcor
BSM1733
Masimo
3
IBP, CO2,
CO, BIS,
2nd SpO2
ECG (3/6/12 lead)
Resp (impedance)
SpO2
NIBP
Dual Temp
ECG/BP Out
Note: AY-660P is not available in Europe.
3
Optimized for each site and each specialist
OR:
Triple display
Life Scope G9 allows three independent
displays. Different displays can provide different
information for the anesthesiologist, physician
and heart-lung machine operator or other
specialist.
Multi-gas measurement
You can measure CO 2 , N 2 O, O 2 , and five
anesthetic agents (Halothane, Isoflurane,
Enflurane, Sevoflurane and Desflurane). Gases
can be measured quickly with small sampling
flow rate. (Requires an optional GF-110PA or
GF-210R multi-gas unit or GF-120PA or
GF-220R multi-gas/flow unit.)
MAC value
LifeScope G9 can calculate MAC (Minimum
Alveolar Concentration) which helps predict how
much anesthetic will be required during surgery.
(Requires an optional GF-110PA or GF-210R
multi-gas unit or GF-120PA or GF-220R multigas/flow unit.)
Respiratory loops
PV loop and FV loop can be displayed. This
helps respiration management of patients
connected to an anesthesia machine. (Requires
an optional GF-120PA or GF-220R multigas/flow unit.)
BIS monitoring
BIS monitoring helps clinicians determine and
administer the precise amount of anesthesia
drug to meet the needs of each individual
patient.
TOF monitoring
TOF can be performed by connecting a
neuromuscular transmission monitor. Objective
neuromuscular block monitoring is useful during
the entire anesthetic and surgical procedure.
G9 shows TOF ratio, TOF counts and PTC on
the display.
PPV/SPV
PPV (Pulse Pressure Variability) and SPV
(Systolic Pressure Variability) is an indicator of
intravascular volume. It is useful in guiding fluid
therapy for patients receiving mechanical
ventilation.
esCCO
The optional QP-192P esCCO software/ QP193P esCCO/Hemodynamics review program
enable esCCO measurement. esCCO is a new
technology to calculate cardiac output noninvasively and continuously. esCCO uses PWTT
(Pulse Wave Transit Time) which is obtained
from the SpO 2 and ECG-signals. It can
continuously display CCO, CCI, SV, SVI, SVR
and SVRI.
Hemodynamics Review Program
The optional QP-193P esCCO/Hemodynamics
Review Program provides calculation and trend
display to support advanced intensive therapy
management.
A hemodynamics graph provides a graphic view
of overall hemodynamic information. It allows a
more intuitive approach to diagnostic and
therapeutic decision making in hemodynamic
management.
A target graph for PPV and esCCO provide
minimally invasive hemodynamic monitoring.
G9 also has the target graph based on Forrester
Classification to support the intermittent invasive
parameters such as cardiac output by bolus
thermodilution and pulmonary wedge pressure.
Bypass function (All alarms off)
You can turn all alarms off indefinitely when a
heart-lung machine is connected to the patient.
ICU:
PPV/SPV
PPV (Pulse Pressure Variability) and SPV
(Systolic Pressure Variability) is an indicator of
intravascular volume. It is useful in guiding fluid
therapy for patients receiving mechanical
ventilation.
esCCO
The optional QP-192P esCCO software/ QP193P esCCO/Hemodynamics review program
enable esCCO measurement. esCCO is a new
technology to calculate cardiac output noninvasively and continuously. esCCO uses PWTT
(Pulse Wave Transit Time) which is obtained
from the SpO 2 and ECG-signals. It can
continuously display CCO, CCI, SV, SVI, SVR
and SVRI.
CVP_ET
Respiration affects the intrapleural pressure and
makes the CVP value unstable. Nihon Kohden’s
original technology of CVP_ET (end tidal CVP)
uses the mainstream CO 2 signals to calculate
the CVP at the end tidal CO 2 point. CVP_ET
provides a stable and physiologically correct
CVP value.
Hemodynamics Review Program
The optional QP-193P esCCO/Hemodynamics
Review Program provides calculation and trend
display to support advanced intensive therapy
management.
A hemodynamics graph provides a graphic view
of overall hemodynamic information. It allows a
more intuitive approach to diagnostic and
therapeutic decision making in hemodynamic
management.
4
A target graph based on EGDT is useful when
applying sepsis treatment protocols.
Mainstream EtCO2 for both intubated and
non-intubated patients
Life Scope G9 can use the compact and light
weight (about 2g sensor) TG-920P cap-ONE
mainstream CO 2 sensor kit to obtain smooth and
accurate EtCO 2 and respiration rate within 5
seconds.
8-channel EEG
EEG monitoring is available with the optional
AE-918P neuro unit. Up to 8 channels of EEG
can be monitored on the home screen.
CSA/DSA
CSA and DSA show the power in each EEG
frequency band plotted over time. CSA and DSA
can help spot EEG trends and changes in brain
function which might not be obvious from the
raw waveforms.
CCU:
12 lead ECG simultaneous display
12-lead ECG waveform can be displayed on the
home screen. This makes it easier to recognize
multi-focus VPC, ST change and ventricular
hypertrophy.
12-lead ECG analysis
The 12-lead ECG analysis of Life Scope G9 has
the same accuracy and reliability as a dedicated
electrocardiograph. There is no need to change
electrodes to another instrument.
Arrhythmia detection
Upgraded arrhythmia detection lets you analyze
multi-channel ECG. The multi-template matching
method reduces false alarms and assures high
quality detection. 23 arrhythmia items can be
detected.
ST display and review
ST waveforms of all ECG leads can be
displayed. The reference ST waveforms are also
displayed so you can see changes in the ST
waves. You can adjust the ISO point, J point and
ST point for ST level measurement.
ST review shows the ST level on a multi-axis
chart. This helps the clinicians easily recognize
ST change and location in the heart.
NIBP inflation pressure for neonate
Connection of a neonate NIBP air hose is
detected and the inflation pressure range is
automatically changed for patient safety.
OCRG
OCRG (oxycardiorespirogram) combines
compressed trends of beat-to-beat heart rate,
respiration, and oxygenation levels. OCRG can
help the doctor detect the cause of apnea attack.
Dual SpO2
Monitoring the difference in SpO 2 between right
upper limb (pre-ductal) and lower limb (postductal) is useful to diagnose PPHN (Persistent
Pulmonary Hypertension of Newborn), decide
the timing to start and stop treatment as well as
the operation schedule.
aEEG (amplitude-integrated EEG)
Because the brain of a newborn baby is
immature, it is difficult to detect seizures by
observation. Life Scope G9 provides aEEG
which makes it easier to detect brain seizure.
aEEG monitoring is also becoming important in
hypothermia therapy for neonatal
encephalopathy.
Mainstream CO2 sensors for neonate
Mainstream CO 2 monitoring for neonate is
available with a compact and lightweight (about
2 g sensor) cap-ONE TG-970P CO 2 sensor kit. It
has a dead space of only 0.5 ml.
PI (Pulse-amplitude Index)
The Pulse-amplitude Index indicates the
percentage of pulsatile signal in the entire
transmitted IR signal. PI supports to assess
peripheral perfusion.
(PI is displayed when using Nihon Kohden SpO 2
sensors)
SQI bar graph for SpO2
The SQI (signal quality index) bar graph shows
the pulse waveform quality for SpO 2
measurement.
Non-adhesive SpO2 probe
The TL-260T (P205A) Multi-site Y probe is
designed so that the adhesive of the attachment
tape does not stick to the delicate skin of
neonates or low birth weight infants.
Network
NICU:
Neonate arrhythmia algorithm
Life Scope G9 has software for monitoring
neonates. A dedicated neonate arrhythmia
recognition algorithm recognizes narrow QRS.
LS-NET (Life Scope Networking)
You can connect Nihon Kohden central monitors
and bedside monitors by LS-NET (Life Scope
Networking with Ethernet LAN).
Wireless networking
With wireless LAN station QI-320PA and
wireless LAN access point YS-095P5, wireless
networking is available. With the wireless LAN
option, you can connect Life Scope G9 to an LS-
5
NET network by Wireless LAN, IEEE 802.11
a/b/g.
available when the Life Scope G9 bedside
monitor is connected to the central monitor.
Interbed
When Life Scope bedside monitors are
connected in an LS-NET network, you can
exchange and view data of other bedside
monitors. Both individual display and 16 bed
display are available.
Drug calculation
Life Scope G9 can calculate the flow rates and
dosages for medication titration. This is the ideal
solution for medical and paramedical personnel
who need rapid dose calculation. In addition to
preset drugs, you can add custom medications.
Connecting to a network printer without a central
monitor
You can connect a network printer directly to a
Life Scope G9 monitor through the LAN port.
You can print the screen capture on A4 paper.
Respiration calculation
Life Scope G9 can calculate respiration
dynamics. the flow rates and dosages for
medication titration. This is the ideal solution for
medical and paramedical personnel who need
rapid dose calculation. In addition to preset
drugs, you can add custom medications.
Other Features
Screen capture
You can save Life Scope G9 screen capture
images and transfer bit map data by USB.
This is helpful for preparing clinical reports.
iNIBP
Nihon Kohden's unique iNIBP inflation algorithm
provides fast and painless measurement of NIBP.
iNIBP is available when a Life Scope PT
transport monitor is used as the input unit.
Nihon Kohden’s YAWARA CUFF 2 NIBP cuffs
prevent bruising, increase patient comfort and
reduce noise for more accurate NIBP
measurement.
PWTT-triggered NIBP measurement
PWTT (pulse wave transit time) is continuously
and non-invasively measured from the ECG and
SpO 2 . If a sudden, critical circulation change
happens between the periodic NIBP
measurements, PWTT may detect it and trigger
NIBP measurement to confirm it.
Graphical and tabular trends
Up to 168 hours of graphic and tabular trends of
all parameters can be saved and reviewed.
Full disclosure
Up to 168 hours of full disclosure waveforms for
5 parameters can be saved and reviewed. With
optional SSD (YS-105P0), up to 168 hours of all
waveforms can be saved and reviewed.
Alarm escalation
The alarm escalation function automatically
escalates the alarm priority to a selected level if
the alarm continues or SpO 2 drops. Alarm
escalation applies to vital alarms (SpO 2 limit and
apnea) and technical alarms (ECG and SpO 2 ).
Alarm escalation can contribute to decreased
medical accidents and improved quality of care.
Sleep mode
Sleep mode prevents the monitor from
disturbing the patient during sleep or other times.
The screen is darkened and the sync sound and
alarm indicator are turned off. Sleep mode is
6
SYSTEM COMPOSITION
LCD display unit
VL-190P
Local purchase
display
Display expansion
board
YS-104P5
Recorder
WS-960P
Third display
Smart unit
AA-672P
AA-674P
Input unit
AY631/633/
651/653/
661/663P
Input unit
AY-660P
Core unit
CU-191R
CU-192R
Alarm indicator
YL-920P
Bedside
monitor
BSM-1733
BSM-1753
BSM-1763
Data Acquisition Unit
JA-690PA
JA-694PA
Multi amp unit
AA-910P
Neuro unit
AE-918P
Interface unit
JA-920P
Interface
QF series
Communication
cable
IF series
Multi-gas unit
GF-110PA/210R
Multi-gas/flow
unit
GF-120PA/220R
Wireless LAN
station
QI-320PA
Optional module,
external device
Mouse
Keyboard
Bar code reader
USB flash drive
Wireless LAN
Access point
YS-095P5
Network
isolation unit
HIT-100
Remote
controller
RY-910PA
Central monitor
Central monitor
Network printer
7
Display delay time:
Diagnostic and monitor mode: ≤ 250 ms
Filter mode: ≤ 1 s
Numerical data display:
Heart rate, VPC rate, ST level, respiration rate,
NIBP (systolic, diastolic, mean), PWTT, delta
PWTT, IBP (systolic, diastolic, map), SpO2, SpO 22, delta SpO 2, pulse rate, temperature, CO, CI, Ti
(injectate temperature), Tb (blood temperature), O 2
concentration, EtCO2, BIS, inspired/ expired N2O
concentration, inspired/ expired CO2 partial pressure,
inspired/ expired CO2 concentration, inspired/ expired
O2 concentration, inspired/ expired anesthetic agent
concentration (Halothane, Isoflurane, Enflurane,
Sevoflurane, Desflurane), MAC (minimum
alveolar concentration), Ppeak (peak airway
pressure), PEEP (positive end expiratory
pressure), Pmean (mean airway pressure), MV
(minute volume), TVi (inspiratory tidal
volume),TVe (expiratory tidal volume), C
(compliance), R (airway resistance), Ri
(inspiratory airway resistance), Re (expiratory
airway resistance), I:E (inspiration expiration
ratio), SEF (90 or 95% spectral edge frequency),
MDF (median frequency), PPF(peak power
frequency), TP (total power), power of frequency
(Absδ, Absθ, Absα, Absβ, Absγ), power ratio of
frequency (%δ, %θ, %α, %β, %γ), CSA
(compressed spectral array), DSA (density
spectral array), CCO, SVRI, SvO 2 , EF, ScvO 2 ,
CCI, EDV, SVR, EDVI, PCCO, PCCI, tcPO 2 ,
tcPCO 2 , PPV, SPV, rSO 2 , esCCO, esCCI, esSV,
esSVI, esSVR, esSVRI
Synchronization mark:
Heart rate sync mark, pulse rate sync mark,
respiratory sync mark
Upper and lower alarm limit display:
Numeric value and mark
Specification
◆
◆
Language
Available language:
Czech, English, Finnish, French, German, Italian,
Norwegian, Portuguese, Polish, Romanian,
Russian, Spanish
Measuring parameters
ECG(3/6/12 lead), respiration (impedance
method), SpO 2 , SpO 2 -2, NIBP, IBP, temperature,
cardiac output, respiration (thermistor method),
FiO 2 , BIS, APCO, CO 2 (mainstream method),
1
1
CO 2 (sidestream method)* , anesthetic gas*
1
1
(CO 2 , O 2 , N 2 O, agent), Flow/Paw* , EEG* ,
2
2
2
2
TOF* , ventilation* , CCO* , SvO 2 * ,
2
2
3
tcPO 2 /tcPCO 2 * , rSO 2 * , esCCO*
1
* : Optional module/unit is required.
2
* : External device and interface are required.
*3: Optional software QP-192P/193P is required.
◆
Display
Display size (Color LCD):
19 inch wide (VL-190P)
CANVYS (Local purchase display)
18.5 inch wide (MDRAP18EAXAC-N1)
21.5 inch wide (MDRAP21EAXAC-N1)
24 inch wide (MDRAP24XAXAC-N1)
Viewing area:
409 × 256 mm (VL-190P)
409 x 230 mm (MDRAP18EAXAC-N1)
476 x 268 mm (MDRAP21EAXAC-N1)
531 x 298 mm (MDRAP24XAXAC-N1)
Resolution:
1,680 × 1,050 dots (VL-190P)
1,366 x 768 dots (MDRAP18EAXAC-N1)
1,920 x 1,080 dots (MDRAP21EAXAC-N1)
1,920 x 1,080 dots (MDRAP24XAXAC-N1)
Number of displays:
2 displays (3 displays when optional display
expansion board (YS-104P5) installed.
Number of traces:
17 traces on one display
34 traces on two displays
51 traces on three displays
Touch panel operation: available
Waveform display mode: Non-fade moving or
non-fade fixed
Normal Sweep speed: 25, 50 mm/s
Slow sweep speed: 1.56, 6.25, 12.5 mm/s
Display colors: 32, selectable
Displayed waveforms:
ECG (maximum 12 traces), IBP (maximum 8
traces), SpO2 pulse wave, SpO2 -2 pulse wave, CO2
partial pressure curve, EEG (maximum 8 traces),
respiratory flow curve, airway pressure curve,
respiratory volume curve, EEG (BIS), O2 concentration
curve, CO 2 concentration curve, anesthetic agent
concentration (Halothane, Isoflurane, Enflurane,
Sevoflurane, Desflurane)
◆
◆
Screen details
Site specialized setting:
OR, ICU, NICU, Ward, ER
Number of screen layout master: 20
Numeric position: Selectable, right or left
Review data display with numeric value and
waveform: Available, side and/or bottom
Number of function key: Up to 20 in each
display
Review data display with numeric value and
waveform: Available, side and/or bottom
Sleep mode: Available when connected to
central monitor.
Alarm
Alarm items: Upper/lower alarms, arrhythmia
alarms, interbed alarms, technical alarms
Alarm types: Crisis (red, blinking), Warning
(yellow, blinking), Advisory (yellow or blue, lit),
Message
Alarm indication: Message, highlighted numeric
value, blinking alarm indicator, alarm sound
Alarm suspend: Provided (for 1, 2, 3 min, Off)
When connected to a central monitor, this alarm
can be adjusted from the central monitor.
8
Alarm escalation: Available
Alarm configurable start-up values:
Master Alarm Neonatal, Master Alarm Pediatric,
Master Alarm Adult
Number of master setting:
Up to 4 for each of Adult, Pediatric and Neonatal
mode.
Auto alarm setting: Upper/Lower alarm, ST
level
◆
◆
◆
◆
-
◆
Sound
Type of sound: Alarm, synchronization, key
clicking, NIBP completion sound
Alarm sound:
- Crisis: Continuous pip sound, continuous
ping sound or IEC standard
- Warning: Continuous bing bong sound,
continuous ding ding sound or IEC
standard
- Advisory: Single beep every 20 seconds or
single beep every 120 seconds or IEC
standard
Synchronization sound:
Sync source: ECG, SpO 2 or IBP
Sync tone: High, medium or low
Pitch automatically changes depending on the
SpO 2 or IBP value
Volume: Changeable (alarm sound cannot be
silenced for safety)
Power
Core unit: AC power
Input unit: DC power from the core unit
VL-190P LCD unit: AC power or DC power from
the core unit
Other LCD unit: AC power
Interface on core unit
Display I/F: 2 (3 when optional board installed),
Image signal (DVI), touch panel and alarm
indicator (RS-232C), USB, GPIO (power switch,
service key, check key)
Sound output I/F: Sound signal (analog signal)
Sound input IF: Microphone signal (analog
sound)
USB I/F: 8
Recorder I/F: RS-232C
Network I/F: 10/100/1000BASE-T
Multilink I/F: 3, based on 5V UART
Universal serial I/F: RS-232C
EJA unit (Interface unit, JA-920P) I/F: Based
on RS-422
DAU I/F: LVDS(Low Voltage Differential
Signaling)
Recording
Recording mode:
- Manual: Real time waveform recording,
recording on the review, analysis and
calculation windows
- Automatic: Alarm recording, periodic
recording
Waveform recording:
◆
Recording width: ≥ 46mm
Recording speed: 12.5, 25, 50 mm/s
Number of traces: Maximum 3 traces
Recorder items: Date and time, patient
information, measurement values, causes of
arrhythmia message recording, waveform
name, filter on/off, sensitivity, speed
Network
Network communication (LS-NET):
Connects to the Nihon Kohden monitor network
and communicates with central monitor, other
bedside monitors and server.
Network communication (hospital network):
Connects to the hospital network.
Wireless LAN (when connected wireless
LAN station QI-320PA)
Wireless LAN standard:
IEEE 802.11b, IEEE 802.11g, IEEE802.11a
Output power: 10mW/MHz or less
◆
Review
Up to 168 hours data for each review screens
can be displayed.
Trend graph:
- Storage capacity: 168 hours
- Types of trend graph: 5 trend graphs, BIS, CSA
and DSA
- Number of parameters in each trend graph:
6
Vital list:
- Storage capacity: 168 hours for up to 108
parameters
- Number of vital list: 6
- Number of parameters displayed in each list:
Up to 18 parameters
- List interval: 1, 5, 10, 15, 30 or 60 min
NIBP list:
- Storage capacity: 1,008 files
- Number of parameters displayed in the NIBP
list: Up to 18 parameters
- List interval: at NIBP measurement
HEMO list:
- Storage capacity: 1,008 files
- Number of parameters displayed in the
- Hemo list: Up to 18 parameters
Respiration calculation list (Lung list):
- Storage capacity: 1,008 files
- Number of parameters displayed in the
- Lung list: Up to 18 parameters
Full Disclosure:
- Storage capacity:
5 waveforms for a period of 168 hours
8 waveforms for a period of 96 hours
35 waveforms for a period of 24 hours
With optional SSD (YS-105P0), all waveforms
for a period of 168 hours
Wave duration: 60, 30, 20, 12 or 6 seconds
ST Recall:
- Storage capacity: 10,080 files + 1 reference
file
- Storage interval: 1 minute
- Item: ST level waveforms of all monitoring
9
ECG
ST review (ST level on multi-axis chart):
Available
Alarm History:
- Storage capacity: 302,400 files for the past
168 hours
- Item: Vital sign alarms, arrhythmia alarms,
technical alarms and operational alarms
Arrhythmia Recall:
- Storage capacity: 60,480 files
- 23 items: ASYSTOLE, VF, VT, EXT TACHY,
EXT BRADY, VPC RUN, V BRADY, SV
TACHY, TACHYCARDIA, BRADYCARDIA,
PAUSE, COUPLET, EARLY VPC,
MULTIFORM, V RHYTHM, BIGEMINY,
TRIGEMINY, FREQ VPC, VPC, IRREGULAR
RR, PROLONGED RR, NO PACER PULSER,
PACER NON-CAPTURE
12-lead interpretation:
- Storage capacity: 672 files
- 12 lead ECG interpretation: ECAPS 12C
(BSM), measurements and diagnostic,
Available when monitoring 12 leads
- Item: 12 lead analysis results, analyzed
waves, interpretation, averaged waves
- Analysis patient age: 3 years to adult
Hemodynamics graph (optional QP-193P is
required):
- Storage capacity: 168 hours
- Window types: Trend + target graph, trend,
target graph
- Number of target graph: 4
- The default setting for target graph 3 is
based on EGDT (Eearly Goal Direct
Therapy)
- The default setting for target graph 4 is
based on Forrester Classification
aEEG:
- Storage capacity: 168 hours
- Number of aEEG trend graph: 6 pattern
- Number of channels in each trend graph:
up to 4 channels
- Number of EEG waveform in each trend
graph: up to 4 channels, when set to save
in full disclosure
OCRG:
- Storage capacity: 168 hours
- OCRG item: Past measured value (Heart
rate and SpO 2 , SpO 2 -2) and compressed
respiration
- Parameters on additional graph (up to 2
graphs): CO 2, IBP, tcPO 2 / PCO 2, aEEG1 to
aEEG8
- Display events: Brady/HR lower, SpO 2
upper, SpO 2 lower, SpO 2 -2 upper, SpO 2 -2
lower, delta SpO 2, Apnea, Press-S limits,
Press-D limits, Press-M limits, SEF limits,
TP limits, Key operation, mark
Short trend:
- The latest 30 minute parameter data can
be displayed as a trend graph on the
home screen. This short trend graph can
be dragged left or right by touch panel
operation.
bed- side monitor connected by Ethernet can be
reviewed.
Display items for bed display window:
- Number of bed: up to 16 beds
- Waveform: None
- Numeric data: Monitored parameters
Display items for individual bed window:
- Waveform: 2 traces (ECG + selectable from
measurement data
- Numeric data: Monitored parameters
Interbed Alarm:
-
◆
Interbed
Waveforms and data of other Life Scope series
-
-
◆
Interbed alarm notification: Available (When
an alarm occurs at an interbed bed, an
interbed alarm is generated on the bedside
monitor.)
Silencing the interbed alarm: Available
ECG
Complies with IEC 60601-2-27: 2005,
ANSI/AAMI EC13: 2002.
Leads:
3-electrode cable: I, II, III
6-electrode cable: I, II, III, aVR, aVL, aVF, 2
from V1 to V6
10-electrode cable: I, II, III, aVR, aVL, aVF, V1 to V6
Defibrillation-proof:
- ECG input protected against 400 Ws/DC 5
kV
- IEC 60601-2-27 17.101 compatible
Electrode offset potential tolerance: ≥ ±500 mV
Input dynamic range: ≥ ±5 mV
Internal noise: ≤ 30 µVp-p (Referred to input)
Common mode rejection ratio: ≥ 95 dB
Input bias current: ≤ 100 nA
Frequency response:
- DIAG mode: 0.05 to 150 Hz (–3 dB)
- ST mode: 0.05 to 18 Hz (–3 dB)
- MONITOR mode: 0.3 to 40 Hz (–3 dB)
- MAXIMUM mode: 1 to 18 Hz (–3 dB)
Input impedance:
- ≥ 5 MΩ (at 10 Hz)
- ≥ 2.5 MΩ (at 0.67 to 40 Hz)
ESU protection: Provided (IEC 60601-2-27:
2005 compatible)
Pacing pulse detection: 0.1 to 2 ms, ±2 to 700
mV, on or off selectable
Leads-off sensing: Each leads has own sensing
with user configurable automatic lead change
Auto lead number recognition: Automatically
judge the number of electrodes by the
connection cable and ECG signal and set the
available leads
Leads-off sensing: Each leads has own sensing
with user configurable automatic lead change
- Active electrode: < 100 nA
- Reference electrode: < 900 nA
Waveform display:
- Display sensitivity: 10 mm/mV ±5% (DIAG
mode at ×1 sensitivity)
- Number of channels: 3 (maximum, with 6 or
10 electrodes on home screen), 12
(maximum, with 10 electrodes on home
screen and 12 LEAD window)
- Sensitivity control: ×1/8,×1/4, ×1/2, ×1, ×2,
AUTO
- Pacing mark display: Available
10
Recording sensitivity: 10 mm/mV ±5% (same
as the display sensitivity)
AC hum filter: ≤ –40 dB (at 50 or 60 Hz)
Heart rate count:
- Calculation method: Moving average/
Instantaneous beat to beat
- Counting range: 0, 15 to 300 beats/min (±2
beats/min)
- Counting accuracy: ±2 beats/min (0, 15 to
300 beats/min, essential performance in
EMC standard)
- QRS detection (at × 1 sensitivity):
Adult:
Width: 70 to 120 ms
Amplitude: 0.5 to 5 mV
Rate: 30 to 200 beats/min
Child and neonate:
Width: 40 to 120 ms
Amplitude: 0.5 to 5 mV
Rate: 30 to 250 beats/min
- Heart rate sync mark delay time: Within 100
to 200 ms (when QRS is detected)
- Display update cycle: Every 3 s or when
alarm is generated
- Heart rate averaging: Method for calculating
the average from the instantaneous heart
rate: Calculated by using the most recent 4
or 12 beats
- Tall T-wave rejection capability: Complies
with the heights of T-waves from 0 mV to 1.2
mV specified in ANSI/ AAMI EC13 Sect.
4.1.2.1(c)
Pacemaker pulse detector rejection of fast
ECG signals:
Slew rate at which the pacemaker pulse detector
responds: 6 to 8 V/s
Tested as specified in ANSI/AAMI EC13: 2002
Sect. 4.1.4.3
Pacemaker pulse rejection capability, without
overshoot:
Complies with the amplitudes of pacemaker pulses
±2 to ±700 mV and widths 0.1 to 2 ms specified in
ANSI/AAMI EC13: 2002 Sect. 4.1.4.1
Pacemaker pulse rejection capability, with
overshoot:
Overshoot amplitudes and time constants of
±0.12 mV/100 ms to ±2 mV/4 ms
(As defined by method B of ANSI/AAMI EC13:
2002 Sect. 4.1.4.2, this corresponds to the
pacemaker pulses amplitudes and widths of ±4
mV/2 ms to amplitudes ±80 mV/0.1 ms.)
Heart rate alarm:
Upper limit range: 16 to 300 beats/min, OFF in
1 beat/min steps
Lower limit range: OFF, 15 to 299 beats/min in
1 beat/min steps
Alarm items: TACHYCARDIA, BRADYCARDIA,
Escalating Alarm leads off time
Arrhythmia analysis:
Analysis method: Multi-template matching
method
Number of channels: 2
QRS detection type: Adult, child, neonate
VPC counting rate: 0 to 99 VPCs/min
Arrhythmia message: ASYSTOLE, VF, VT, EXT
TACHY, EXT BRADY, VPC RUN, V BRADY, SV
TACHY, TACHYCARDIA, BRADYCARDIA,
PAUSE, COUPLET, EARLY VPC, MULTIFORM,
V RHYTHM, BIGEMINY, TRIGEMINY, FREQ
VPC, VPC, IRREGULAR RR, PROLONGED RR,
NO PACER PULSER, PACER NON-CAPTURE
Other messages: NOISE, CHECK
ELECTRODES, LEARNING
Arrhythmia alarm: Upper limit range: OFF, 1 to
99 VPC/min
Number of arrhythmia recall files: 60,480 files
Storage time per file: 8 s
ST level measurement:
Number of measurement channels:
3-electrode: 1 ch
6-electrode: 8 ch
10-electrode: 12 ch
ST level measuring range: ±2.5 mV
Measurement point: automatic with possibility to
adjust manually
ST level alarm:
Upper limit range: –1.99 to 2.00 mV in 0.01 mV
steps, OFF
Lower limit range: OFF, –2.00 to 1.99 mV in 0.01
mV steps
Storage capacity: 168 hours
Cascade ECG waveform: available
◆
Non Invasive Blood Pressure, NIBP
Complies with IEC 60601-2-30: 1999.
Measuring method: Oscillometric
Measuring range: 0 to 300 mmHg
Accuracy:
±3 mmHg (0 mmHg ≤ NIBP < 300 mmHg)
±4 mmHg (200 mmHg ≤ NIBP ≤ 300 mmHg)
Cuff inflation time:
≤ 7 s (700 cc), 0 to 200 mmHg
≤ 5 s (72 cc), 0 to 200 mmHg
Typical measurement time:
Inflation mode (iNIBP)
Adult/Pediatric: 13 s
Deflation mode
Adult/Pediatric: 22 to 33 s (depends on the input
unit)
Neonate: 20 s
Initial pressurization value(default setting):
Adult: 180 mmHg*
Child: 140 mmHg*
Neonate: 100 mmHg*
*It is settable
Maximum pressurization value:
Adult/Child: 300 mmHg
Neonate: 150 mmHg
Maximum measurement time:
Adult/Child: ≤ 160 s
Neonate: ≤ 80 s
Operation mode: Manual, STAT, periodic, SIM
(depends on the SITE setting)
Measurement mode: Adult, child or neonate is
recognized by connected air hose
Air leakage: ≤ 3 mmHg/min
Display items: Systolic (SYS), diastolic (DIA),
mean (MAP)
Other display: Oscillation graph, PR, Cuff
pressure (displays cuff pressure during
measurement)
NIBP data display update cycle: Updated
every measurement
11
Measurement completion sound: Generated at
measurement completion (depends on the
setting)
Alarm (SYS, DIA, MAP):
Upper limit range: 15 to 260 mmHg in 5 mmHg
steps, OFF
Lower limit range: OFF, 10 to 255 mmHg in 5
mmHg steps
Safety:
- Maximum pressurization value cuff
inflation limiter:
Adult/Child: 300 to 330 mmHg
Neonate: 150 to 165 mmHg
- Cuff inflation time limiter:
Adult/Child: 161 to 165 s
Neonate: 81 to 84 s
- Interval time limiter: 25 to 29 s
Power discontinuity: Deflate immediately after
power down
Venous puncture mode: Available*
*target pressure is settable
iNIBP (NIBP measurement in inflation method):
Available when a Life Scope PT transport monitor is
used as the input unit
◆
SpO2
Complies with ISO 9919: 2005.
Display:
Display update cycle: Every 3 s or when alarm is
generated
Sync tone modulation: Changes tone depending
on SpO 2 value
Sweep speed: 25, 50 mm/s
Waveform sensitivity: ×1/8, ×1/4, ×1/2, ×1, ×2,
×4, ×8 or AUTO
Nihon Kohden SpO2 ,AY660/661/663P, BSM-1763
SpO 2 measurement:
Display range: 0 to 100% SpO 2
Declared range: 70 to 100 % SpO 2
1
*2
Measuring accuracy * (rms ):
70%SpO 2 ≤ %SpO 2 < 80%SpO 2 ±3%SpO 2
80%SpO 2 ≤ %SpO 2 ≤ 100%SpO 2 ±2%SpO 2
Pulse rate measurement:
Display range: 30 to 300 beats/min
Declared range: 30 to 300 beats/min
1
*2
Counting accuracy* (rms ): ±3%±1 beat/min
PI(Pulse-amplitude Index): available
SQI bar graph: available
SpO 2 -2: available
Delta SpO 2 : available
oximeter is connected.
Delta SpO 2 : available when OxiMax N-600x
pulse oximeter is connected.
Masimo SpO2 , AY-631/633P, BSM-1733
SpO 2 measurement:
Display range: 1 to 100% SpO 2
Declared range: 70 to 100 % SpO 2
1
*2
Measuring accuracy (rms ):
No motion: ±2%SpO 2 (adult)
±3%SpO 2 (neonate)
Motion: ±3%SpO 2 (adult)
±3%SpO 2 (neonate)
Pulse rate measurement:
Display range: 25 to 240 beats/min
Declared range: 25 to 240 beats/min
1
*2
Counting accuracy* (rms ):
No motion: ±3 beats/min
Motion: ±5 beats/min
SpO 2 -2: available when Masimo pulse oximeter
is connected.
Delta SpO 2 : available when Masimo pulse
oximeter is connected.
PI (Perfusion Index): available
Signal IQ : available
1
* Essential performance n EMC standard
*2
The rms is the difference between
measurement value and standard reference
value calculated by root-mean-square
SpO 2 /SpO 2- 2 alarm:
- Upper limit range: 51 to 100%SpO 2 in
1%SpO 2 steps, OFF
- Lower limit range: OFF, 50 to 99%SpO 2 in
1%SpO 2 steps
- Delta SpO 2 alarm: 1 to 50%SpO 2 in
1%SpO 2 steps, OFF
Pulse rate alarm:
- 31 to 300 beats/min in 1 beat/min steps, OFF
- Lower limit range: 30 to 299 beats/min in 1
beat/min steps, OFF
Alarm escalation: SpO2, Apnea, technical alarm
- SpO2: Delay time (alarm continues for a set
time), value drop
- APNEA: Delay time, value drop
Response time (Nihon Kohden SpO2 only):
Response selection: Fast, Norm, Slow
Response time: Examples of response times
corresponding to changes in the SpO2 value and
pulse rate (PR) are shown below.
Example 1: PR=70 bpm, and SpO 2 value is
changed at 0.6% per second
SpO 2 -2, Delta SpO 2 cannot be monitored by
using the MULTI socket on the AY-660P.
Nellcor SpO2 , AY-651/653P, BSM-1753
SpO 2 measurement:
Display range: 1 to 100% SpO 2
Declared range: 70 to 100 % SpO 2
1
*2
Measuring accuracy (rms ):
±2%SpO 2 (adult)
±3%SpO 2 (neonate)
Pulse rate measurement:
Display range: 20 to 300 beats/min
Declared range: 20 to 250 beats/min
1
*2
Counting accuracy* (rms ): ±3 beat/min
SpO 2 -2: available when OxiMax N-600x pulse
Example 2: PR=140 bpm, and SpO 2 value is
changed at 0.6% per second
12
counts/min steps, OFF
Lower limit range: OFF, 0 to 148 counts/min in 2
counts/min steps
Apnea alarm: OFF, 5 to 40 s in 5 s steps
Displayed message: APNEA
Alarm escalation: apnea
◆
Example 3: PR=140 bpm, and SpO 2 value is
changed at 0.6% per second
◆
Respiration (impedance)
Measuring method: Transthoracic impedance
pneumography
Number of channels: Selectable from R-F or RL
Measuring impedance available range: 220 Ω to
4 kΩ
Excitor current:
AY-600 series: 45 ±10 µA (rms) at 40 kHz (sine
wave)
BSM-1700 series: 40 ±10 µA (rms) at 40 kHz
(sine wave)
Internal noise: ≤ 0.2 Ω (Referred to input)
Respiration rate counting range: 0 to 150
counts/min
Respiration rate counting accuracy*: ±2
counts/min (0 to 150 counts/min)
* Essential performance in EMC standard
Frequency response (high frequency cut-off):
3 Hz ±1 Hz (–3 dB)
Measurement detection: Automatically detects
electrode attachment and starts monitoring
Impedance respiration: Measurement On/Off
available
Heart beat rejection: Available
Waveform display:
Display sensitivity: 10 mm/1 Ω ±25% (at ×1
sensitivity)
Sensitivity control: ×1/16, ×8, ×1/4, ×1/2, ×1, ×2,
×4
Respiration rate display update cycle: Every 3 s
or when alarm is generated
Alarm:
Upper limit range: 2 to 150 counts/min in 2
◆
Temperature
Complies with EN 12470-4: 2000
Thermistor probe: 400 series (YSI)
Labels: The temperature connection cord
connector has a memory chip for saving the set
site label.
Tskin, Tskin2, Tskin3, Trect, Tcore, Tnaso, Teso,
Ttymp, Tblad, Taxil, T1 to T8
Number of channels: 8 channels + Tb
Delta TEMP: 4 (Delta T1 to Delta T4)
Measuring range: 0 to 45°C, 32 to 113°F
Measuring accuracy*:
±0.2°C ( 0°C ≤ TEMP < 25°C)
±0.1°C (25°C ≤ TEMP ≤ 45°C)
* Essential performance in EMC standard
Internal noise: ≤ 0.014°C (at 37°C)
Temperature drift: within ±0.005°C /°C
Display update cycle: Every 3 s or when alarm
is generated
Alarm:
Upper limit range: 0.1 to 45.0°C (33 to 113°F) in
0.1°C (1°F) steps, OFF
Lower limit range: OFF, 0.0 to 44.9°C (32 to
112°F) in 0.1°C (1°F) steps
Delta TEMP: OFF, 0.0 to 45.0°C (33 to 113°F) in
0.1°C (1°F) steps
Invasive blood pressure, IBP
Complies with IEC 60601-2-34: 2000
Labels: ART, ART2, RAD, DORS, AO, FEM, UA,
UV, PAP, CVP, RAP, RVP, LAP, LVP, ICP to ICP4,
P1 to P8
Calculation: CPP, PPV, SPV, CVP-ET
Complied transducer:
P23XL-1 and P10EZ-1 Argon Medical Devices
reusable transducers
Argon Medical Devices disposable transducers
DX series
5 µV/V/mmHg, bridge resistor: 200 Ω to 20 kΩ,
defibrillation-proof, output impedance ≤1 K Ω or
the equivalents
3
Volume displacement: 0.04 mm /100 mmHg
Measuring range: –50 to 300 mmHg
Zero balancing range: ±200 mmHg
Zero balancing accuracy: ±1 mmHg
Measuring accuracy:
±1 mmHg ±1 digit (–50 mmHg ≤ IBP < 100
mmHg)
±1% ±1 digit (100 mmHg ≤ IBP ≤ 300 mmHg)
Total measuring accuracy*: ±4% or ±4 mmHg,
whichever is greater (When used with
ANSI/AAMI BP-22-1994 complied equipments)
*Essential performance in EMC standard
Internal noise: within ±1 mmHg
Temperature drift: ±0.1 mmHg/1°C
Frequency response: DC to 12 Hz or 20 Hz
(selectable)
Cable break detection: Available (detects
13
transducer cable breaking)
Display items: Systolic (SYS), diastolic (DIA),
mean (MEAN)
Display update cycle: Every 3 s or when alarm
is generated
BP sync sound: Systolic value 20 to 120 mmHg,
changes in 20 steps every 5 mmHg
Alarm:
Upper limit range: −48 to 300 mmHg in 2 mmHg
steps, OFF
Lower limit range: −50 to 298 mmHg in 2 mmHg
steps, OFF
Alarm inactivation: Alarm is inactivated in certain
period when zero balancing is performed.
Pulse rate Alarm:
Upper limit range:
16 to 300 beats/min in 1 beat/min steps, OFF
(When SYNC SOURCE is set to ECG)
31 to 300 beats/min in 1 beat/min steps, OFF
(When SYNC SOURCE is set to PRESS or
SpO 2 )
Lower limit range:
OFF, 15 to 299 beats/min in 1 beat/min steps
(When SYNC SOURCE is set to ECG)
OFF, 30 to 299 beats/min in 1 beat/min steps
(When SYNC SOURCE is set to PRESS or
SpO 2 )
◆
Carbon Dioxide, CO2 (Mainstream method)
For the TG-900P/TG-920P/TG-950P*/TG-970P CO2
sensor kit specifications, refer to the kit manual.
Displayed CO 2 *: Values detected by the TG900P/TG-920P/TG-950P/TG-970P CO 2 sensor
kit
* Essential performance in EMC standard
Calculation method:
TG-900P/TG-920P: semi-quantitative
TG-950P/TG-970P: quantitative
CO 2 measuring parameter:
TG-900P/TG-920P: ETCO 2
TG-950P/TG-970P: ETCO 2 , CO 2 (I)
CO 2 measuring range:
TG-900P/TG-920P/TG-950P: 0 to 100 mmHg
TG-970P: 0 to 150 mmHg
CO 2 measuring accuracy:
TG-900P/TG-920P:
±0.4 kPa (0 ≤ CO 2 ≤ 1.33 kPa)
(±3 mmHg (0 ≤ CO 2 ≤ 10 mmHg))
±0.53 kPa (1.33 < CO 2 ≤ 5.33 kPa)
(±4 mmHg (10 < CO 2 ≤ 40 mmHg))
±10% reading
(5.33 < CO 2 ≤ 13.3 kPa (40 < CO 2 ≤ 100
mmHg))
(At 1 atmospheric pressure, air inspiration, no
condensation)
TG-950P/TG-970P:
±0.27 kPa (0 ≤ CO 2 ≤ 5.33 kPa)
(±2 mmHg (0 ≤ CO 2 ≤ 40 mmHg))
±5% reading
(5.33 < CO 2 ≤ 9.33 kPa (40 < CO 2 ≤ 70 mmHg))
±7% reading
(9.33 < CO 2 ≤ 13.3 kPa (70 < CO 2 ≤ 100
mmHg))
(When no condensation)
Warm-up time:
TG-900P/TG-920P: 5 s
TG-950P: 15 s
TG-970P: 10 s
Total system response time:
TG-900P/GT-920P/TG-970P: ≤ 0.5 seconds
TG-950P: ≤ 0.6 seconds
CO 2 value display update cycle: Every 3 s or
when alarm is generated
CO 2 alarm:
Upper limit:
CO 2 (I):
1 to 99 mmHg in 1 mmHg steps, OFF
0.1 to 13.0 kPa in 0.1 kPa steps, OFF
ETCO 2 :
2 to 99 mmHg in 1 mmHg steps, OFF
0.2 to 13.0 kPa in 0.1 kPa steps, OFF
Lower limit:
ETCO 2 :
OFF, 1 to 98 mmHg in 1 mmHg steps
OFF, 0.1 to 12.9 kPa in 0.1 kPa steps
Respiration rate alarm:
Upper limit range: 2 to 150 counts/min in 2
counts/min steps, OFF
Lower limit range: 0 to 148 counts/min in 2
counts/min steps, OFF
Apnea time:
5 to 40 s in 5 s steps, OFF
Displayed message: APNEA
◆
◆
Respiration (Thermistor method)
Complied sensor: TR-900P respiration pickup
for nose and TR-910P respiration pickup for
airway
Measuring items: Thermistor respiration curve,
respiration rate
APNEA detection: Provided
Respiration rate counting range: 0 to 150
counts/min
Apnea detection time: 5 to 40 s
Measurable temperature rage: 10 to 40°C, 50
to 104°F, based on the operating temperature)
Sensitivity: 10 mm/100 Ω ±20%
Apnea detection time: 5 to 40 s
Respiration rate counting accuracy: ±2
counts/min
*Essential performance in EMC standard
Internal noise: ≤ 2.5 Ω, referred to input
Frequency response: 0.1 to 3 Hz (−3 dB)
Waveform display sensitivity: 10 mm/100Ω
±20% (at ×1 sensitivity)
Sensitivity control: ×1/4, ×1/2, ×1, ×2, ×4
Respiration rate display update cycle: Every 3
s or when alarm is generated
Alarm limits:
Upper limit: 2 to 150 counts/min, OFF
Lower limit: 0 to 148 counts/min, OFF
Apnea time: 5 to 40 s in 5 s steps, OFF
Inspired oxygen fractional concentration,
FiO2
Calibration condition: 21 or 100 % O 2
Measuring range: 10 to 100% O 2 I
Measuring accuracy*: ±3 full scale (includes
sensor, when calibrated with air, 21% O 2 )
*Essential performance in EMC standard
Internal noise: ≤0.12% O 2 RMS ±0.72% O 2 p-p
Temperature drift: Within ±0.12%°C/°C
14
Sensor duration detection: Detects the sensor
duration using a sensor output level at
calibration
O2 display update cycle: Every 3 s or when
alarm is generated
Alarm:
Upper limit range: 19 to 100% in 1% steps, OFF
Lower limit range: 18 to 99% in 1% steps
◆
◆
◆
specifications, refer to the JP-600P manual.
Displayed value: CCO, CCI, SV, SVI, SVR,
SVRI, PVR, PVRI, LVSW, LVSWI, RVSW,
RVSWI, SVV
Measuring range: 1 to 20 L/min
3
Volume displacement: ≤0.03 mm /100 mmHg
(FloTrac)
Reproducibility*: ±6% or 0.1 L/min (whichever
is greater)
*Measurement using a variation coefficient-data
generated electrically
Invasive blood pressure (ART)
Measuring range: -50 to +300 mmHg
Stand-alone measuring accuracy (after zero
balance adjustment): ±1% or ±1 mmHg
(whichever is greater)
Total measuring accuracy* (after zero
balance adjustment): ±4% or ±4 mmHg
(whichever is greater)
(when using with bedside monitor)
Cardiac Output, CO
Measuring method: Thermodilution method
Measuring parameters: Cardiac output (CO),
injectate temperature (Ti), blood temperature
(Tb), Thermodilution curve (delta Tb)
Measuring range:
Injectate temperature (Ti): 0°C to 27°C (32 to
81°F)
Blood temperature (Tb): 15°C to 45°C (59 to
113°F)
Thermodilution curve (delta Tb): 0°C to 2.5°C
(32 to 37°F)
Cardiac output (CO): 0.5 to 20 L/min
Measuring accuracy:
Ti: ±0.2°C (0°C to 27°C)
Tb:±0.2°C (15°C ≤ TEMP ≤ 25°C)
±0.1°C (25°C ≤ TEMP < 45°C)
CO: ±5%
Internal noise:
Ti: ≤ 0.025°C RMS/0.15°Cp-p
Tb: ≤ 0.016°C RMS/0.096°Cp-p (correspond to
37°C)
Delta Tb: ≤ 0.005°C RMS/0.03°Cp-p
Temperature drift:
Ti: ±0.005°C /°C
Tb: ±0.005°C /°C
Frequency response (delta Tb): DC to 12 Hz
(–3 dB)
Injectate volume range: 3, 5, 10 mL
Display update cycle: Updated every
measurement
Tb alarm:
Upper limit range: 15.1 to 45.0°C (60 to 113°F)
in 0.1°C (1°F) steps, OFF
Lower limit range: 15.0 to 44.9°C (59 to 112°F)
in 0.1°C (1°F) steps, OFF
Bispectral Index, BIS
For the BISx/BIS processor specifications, refer
to the BISx/BIS processor manual.
BIS can be also monitored with Covidien’s BIS
monitor.
Input channels: 1 or 2 (depends on the BIS
sensor type)
Measuring parameter: Bispectral Index (BIS),
95% Spectral Edge Frequency (SEF),
Suppression Ratio (SR), EMG, Signal Quality
Index (SQI)
Waveform: Real-time EEG
BIS alarm:
Upper limit range: 2 to 100 in 1 steps, OFF
Lower limit range: 0 to 99 in 1 steps, OFF
APCO (CCO)
For the APCO/IBP processor JP-600P
*Essential performance in EMC standard
CCO alarm:
Upper limit range: 1.1
steps, OFF
Lower limit range: 1.0
steps, OFF
CCI alarm:
Upper limit range: 1.1
2
L/min/m steps, OFF
Lower limit range: 1.0
2
L/min/m steps, OFF
◆
to 20.0 L/min in 0.1 L/min
to 19.9 L/min in 0.1 L/min
2
to 20.0 L/min/m in 0.1
2
to 19.9 L/min/m in 0.1
EEG
EEG can be monitored with the AE-918P neuro
unit. For the AE-918P neuro unit specifications,
refer to the AE-918P neuro unit manual.
Number of channels: 8
Measuring range:
SEF, MDF, PPF: 0.0 to 62.5 Hz
TP: 0 to 9.99 nW
ABS δ, ABS θ, ABS α, ABS β, ABS γ: 0 to 9999
pW
% δ, % θ, % α, % β, % γ: 0 to 100%
Maximum undistorted input: > ±2 mV
Polarization voltage: > ±700 mV
Noise: <3 µV p-p (0.53 to 30 Hz)
Input impedance: >15 MΩ at 10 Hz
CMRR: >110 dB (in isolation mode)
Electrode impedance check: >10 kΩ within ±
20%
EEG Sensitivity: 10 µV/1 mm within ±5%
Frequency characteristics:
High range: 70 Hz ±20% at 70% amplitude (−3
dB)
Low range: 0.08 Hz ±20% or time constant 2 s
±20% at 70% amplitude (−3 dB)
AC filter: rejection ratio > 26 dB
Sampling frequency: 200 Hz (A/D Conversion
4 kHz)
Data display update cycle: Every 3 s or when
alarm is generated
SEF alarm:
Upper limit range: 1.0 to 60.0 Hz in 0.5 Hz steps,
OFF
Lower limit range: 0.5 to 59.5 Hz in 0.5 Hz steps,
OFF
15
TP alarm:
Upper limit range: 0.02 to 9.99 nW in 0.01 nW
steps, OFF
Lower limit range: 0.01 to 9.98 nW in 0.01 nW
steps, OFF
◆
◆
Carbon Dioxide, CO2 (sidestream method)
CO 2 in sidestream method can be monitored
with the AG-400R CO 2 unit.
For the AG-400R CO 2 unit specifications, refer
to the AG-400R CO 2 unit manual.
Sampling flow: 50 mL/min +15/−7.5 mL/min
Warm-up time: 30 s average (from power on to
the measurable state)
Measuring range: 0 to 99 mmHg
Measuring accuracy:
0 to 38 mmHg ±2 mmHg
39 to 99 mmHg ± [5 + 0.08 × (χ− 39)] % of
reading
χ: CO 2 partial pressure of a standard gas with a
known CO 2 partial pressure (mmHg)
ETCO 2 and CO 2 (I) alarm:
Upper limit:
CO 2 (I):
1 to 99 mmHg in 1 mmHg steps, OFF
0.1 to 13.0 kPa in 0.1 kPa steps, OFF
ETCO 2 :
2 to 99 mmHg in 1 mmHg steps, OFF
0.2 to 13.0 kPa in 0.1 kPa steps, OFF
Lower limit:
ETCO 2 :
OFF, 1 to 98 mmHg in 1 mmHg steps
OFF, 0.1 to 12.9 kPa in 0.1 kPa steps
Respiration rate measuring range:
101 to 150 counts/min: ±5%
71 to 100 counts/min: ±3%
41 to 70 counts/min: ±2 counts/min
0 to 40 counts/min: ±1 count/min
Respiration rate alarm:
Upper limit range: 2 to 150 counts/min in 2
counts/min steps, OFF
Lower limit range: 0 to 148 counts/min in 2
counts/min steps, OFF
Apnea alarm: 5 to 40 s in 5 s steps, OFF
Displayed message: APNEA
Total system response time: ≤ 4 seconds
Gas
Gas can be monitored with the GF-110PA or GF210R multi-gas unit or GF-120PA or GF-220R
multi-gas/flow unit. For theGF-110PA or GF210R multi-gas unit or GF-120PA or GF-220R
multi-gas/flow unit specifications, refer to the
manual.
Measurement method: Sidestream gas
sampling
Measured parameters: Inspired/expired CO 2
partial pressure, inspired/expired N 2 O
concentration, inspired expired O 2 concentration,
inspired/expired anesthetic agent concentration
(Halothane, Isoflurane, Enflurane, Sevoflurane,
Desflurane), respiration rate, minimum alveolar
concentration
Warm-up time:
GF-110PA/120PA:
within 45 seconds to first measurement
within 10 minutes to measurement with
guaranteed accuracy
GF-210R/220R:
about 1 minute to CO 2 measurement
about 6 minutes to measurement with
guaranteed accuracy
Sampling rate:
GF-110PA/120PA:
70 to 100 mL/min ±10 mL/min
100 to 200 mL/min ±10%rel
GF-210R/220R:
200 mL/min ±20 mL/min
Total system response time:
GF-110PA/120PA:
≤ 5.0 seconds (when sampling volume is 200
mL/min, using adult sampling tube and adult
water trap)
GF-210R/220R:
≤ 5.0 seconds (when YG-610P sampling line is
connected)
CO 2 measurement:
Measurement method: Non-dispersive infrared
ray absorption
Measuring range:
GF-110PA/120PA: 0 to 76 mmHg, 0 to 10.13 kPa
GF-210R/220R: 0 to 10 vol%
Measuring accuracy:
GF-110PA/120PA:
±2 mmHg (0 ≤ CO 2 ≤ 40 mmHg), ±0.27 kPa (0 ≤
CO 2 ≤ 5.33 kPa)
±3 mmHg (40 ≤ CO 2 ≤ 55 mmHg), ±0.40 kPa
(5.33 ≤ CO 2 ≤ 7.33 kPa)
±4 mmHg (55 < CO 2 ≤ 76 mmHg), ±0.53 kPa
(7.33 < CO 2 ≤ 10.13 kPa)
Response time (10 to 90%):
GF-110PA/120PA: ≤ 250 ms (under the condition
of sampling flow is 200 mL/min and sampling
line for adult and water trap for adult is
connected)
Alarm:
Upper limit:
CO 2 (I):
1 to 99 mmHg in 1 mmHg steps, OFF
0.1 to 13.0 kPa in 0.1 kPa steps, OFF
0.2 ETCO 2 :
2 to 99 mmHg in 1 mmHg steps, OFF
0.2 to 13.0 kPa in 0.1 kPa steps, Off
Lower limit:
ETCO 2 :
OFF, 1 to 98 mmHg in 1 mmHg steps
OFF, 0.1 to 12.9 kPa in 0.1 kPa step
N 2 O measurement:
Measurement method: Non-dispersive infrared
ray absorption
Measuring range:
GF-110PA/120PA: 0 to 100%
GF-210R/220R: 0 to 100 vol%
Measuring accuracy:
GF-110PA/120PA: ±3%
Response time (10 to 90%):
GF-110PA/120PA: ≤ 250 ms (under the condition
of sampling flow is 200 mL/min and sampling
line for adult and water trap for adult is
connected)
Alarm (N 2 O(I), N 2 O(E)):
Upper limit: 1 to 100% in 1% steps, OFF
Lower limit: OFF, 0 to 99% in 1% steps
O 2 measurement:
16
Measurement method: Paramagnetic
Measuring range:
GF-110PA/120PA: 0 to 100%
GF-210R/220R: 5 to 100 vol%
Measuring accuracy:
GF-110PA/120PA:
±2% (0 ≤ O 2 ≤ 55%)
±3% (55 < O 2 ≤ 100%)
GF-210R/220R:
±(2.5 vol% + 2.5%rel)
Response time (10 to 90%):
GF-110PA/120PA: ≤ 500 ms (under the condition
of sampling flow is 200 mL/min and sampling
line for adult and water trap for adult is
connected)
Alarm:
Upper limit:
O 2 (I): 19 to 100% in 1% steps, OFF
O 2 (E): 11 to 100% in 1% steps, OFF
Lower limit:
O 2 (I): 18 to 99% in 1% steps
O 2 (E): OFF, 10 to 99% in 1% steps
Anesthetic agent measurement:
Measurement method: Non-dispersive infrared
ray absorption
Measured items: HAL (Halothane), ISO
(Isoflurane), ENF (Enflurane), SEV
(Sevoflurane), DES (Desflurane)
Measuring range:
GF-110PA/120PA:
HAL, ISO, ENF 0 to 5%
SEV 0 to 8%
DES 0 to 18%
GF-210R/220R:
HAL, ISO 0 to 8.5 vol%
ENF, SEV 0 to 10 vol%
DES 0 to 20% vol%
Measuring accuracy:
GF-110PA/120PA:
±0.2% (0 ≤ GAS ≤ 5%)
±0.4% (5 < GAS ≤ 10%)
±0.6% (10 < GAS ≤ 15%)
±1.0% (15 < GAS ≤ 18%)
GF-210PA/220R:
± (0.2%vol% +15%rel)
Response time (10 to 90%):
GF-110PA/120PA:
≤ 300 ms (HAL, ISO, SEV, DES)
≤ 500 ms (ENF) (under the condition of sampling
flow is 200 mL/min and sampling line for adult
and water trap for adult is connected)
Alarm:
Upper limit:
Agent(I), Agent(E) (HAL, ISO, SEV, ENF): 0.1 to
7.0% in 0.1% steps, OFF
DES(I), DES(E): 0.1 to 20.0% in 0.1% steps,
OFF
Lower limit:
Agent(I), Agent(E) (HAL, ISO, SEV, ENF): OFF,
0.0 to 6.9% in 0.1% steps, OFF
DES(I), DES(E): OFF, 0.0 to 19.9% in 0.1%
steps
MAC:
MAC calculating method: selectable,
uncorrected MAC, ambient pressure corrected
MAC or enhanced MAC correction
Respiration rate:
Measuring range: 0, 4 to 60 counts/min
Measuring accuracy: ±1 count/min
Alarm:
Upper limit: 2 to 150 counts/min in 2 counts/min
steps, OFF
Lower limit: OFF, 0 to 148 counts/min in 2
counts/min steps
Apnea alarm: OFF, 5 to 40 s in 5 s steps
Displayed message: APNEA
◆
Flow/Paw
Flow/Paw can be monitored with the GF-120PA
or GF-220R multi-gas/flow unit. For the GF120PA or GF-220R multi-gas/flow unit
specifications, refer to the GF-120PA or GF220R multi-gas/flow unit manual.
FLOW measurement:
Measurement method: Differential pressure
method (fixed orifice)
Measuring range: –3 to +3 L/s
Measuring accuracy: ±3% rel or ±0.005 L/s
whichever is greater (Applicable when 10
minutes or more has elapsed)
Paw measurement:
Ppeak, Pmean, PEEP:
Measuring range: –20 to +100 cmH 2 O, hPa
Measuring accuracy: ±1 cmH 2 O, hPa (Applicable
when 10 minutes or more has elapsed)
Ppeak alarm:
Upper limit range: 1 to 50 cmH 2 O, hPa in 1
cmH 2 O, hPa steps, OFF
Lower limit range: OFF, 0 to 49 cmH 2 O, hPa in 1
cmH 2 O, hPa steps
PEEP alarm:
Upper limit range: 1 to 100 cmH 2 O, hPa in 1
cmH 2 O, hPa steps, OFF
Lower limit range: OFF, 0 to 99 cmH 2 O, hPa in 1
cmH 2 O, hPa steps
Volume measurement:
Measuring range: 0 to 3000 mL
Measuring accuracy: ±5% rel or ±10 mL
whichever is greater (Applicable when 10
minutes or more has elapsed)
TVe, TVi measurement:
Measuring range: 0 to 3000 mL
Display range: 0 to 9999 mL
Measuring accuracy: ±5% rel or ±10 mL
whichever is greater (Applicable when 10
minutes or more has elapsed. Not applicable
when TVi and TVe is less than 100 mL)
MV measurement:
Display range: 0 to 99.9 L/min
Alarm:
Upper limit range: 0.1 to 30.0 L/min in 0.1 L/min
steps, OFF
Lower limit range: OFF, 0.0 to 29.9 L/min in 0.1
L/min steps
C measurement:
Display range: 0.0 to 999.9 mL/cmH 2 O
R, Ri, Re measurement:
Display range: 0.0 to 999.9 cmH 2 O/L/s
Respiration rate measurement:
Counting range: 0, 4 to 60 counts/min
Counting accuracy: ±1 counts/min
Alarm:
Upper limit range: 2 to 150 counts/min in 2
17
BP: DC to 20 Hz ±3 Hz (–3 dB)
HT pulse width: 15 ms
Gain:
ECG: 1000
Offset:
ECG: ≤ ±50 mV
BP: ≤ ±10 mV
Delay:
ECG: 20 ms max
BP: 40 ms max
HT: 20 ms max
counts/min steps, OFF
Lower limit range: OFF, 0 to 148 counts/min in 2
counts/min steps
Apnea time: OFF, 5 to 40 s in 5 s steps
Displayed message: APNEA
◆
esCCO (Optional QP-192P/QP-193P is
required)
Method: estimated continuous noninvasive
cardiac output, pulse wave transit time method
Measured parameter: esCCO, esCCI, esSV,
esSVI, esSVR, esSVRI (To calculate esCCI,
esSVI and esSVRI, patient information (BSA) is
required. To calculate esSVR and esSVRI, ART
and CVP measurement is required.)
Calibration CO source: CO from patient
information, CO from Hemo Trend, CCO,
Manually enter
Calibration pulse pressure source: ART, ART2,
RAD, FEM, NIBP
Measuring range:
esCCO: 0.5 to 20.00 L/min, 0.01 L/min steps
2
esCCI: 0.5 to 20.00 L/min/m2, 0.01 L/min/m steps
esSV: 0 to 300 mL, 1 mL steps
2
2
esSVI: 0 to 200 mL/m , 1 mL/m steps
Alarm range:
esCCO upper limit:0.60 to 20.00 L/min in 0.10
L/min steps, OFF
esCCO lower limit: OFF, 0.50 to 19.90 L/min in 0.10
L/min steps
esCCI upper limit:0.60 to 20.00 L/min in 0.10
L/min steps, OFF
esCCI lower limit: OFF, 0.50 to 19.90 L/min in
0.10 L/min steps
Signal Quality Index: available (4 levels)
◆
ECG/BP Output
ECG waveform output: Output the ECG on the
first trace
BP waveform output: Output the BP waveform
measured with MULTI socket 1 or the highest
priority BP waveform
HT pulse output: Outputs pulse based on the
ECG on the first trace
Complied medical electrical equipments:
Connecting medical electrical equipment must
comply to the following standards:
IEC 60601-1: 1988
IEC 60601-1 Amendment 1: 1991
IEC 60601-1 Amendment 2: 1995
Medical electrical equipment must be connected
by specified method in following standards:
IEC 60601-1-1: 2000
Output impedance:
ECG: ≤100 Ω
BP: ≤100 Ω
Output-waveform:
ECG: ±5.0 V (at 1 mV/V ± 5% sensitivity)
BP: –0.5 to +3.0 V (at 100 mmHg/V ± 1%
sensitivity)
HT: 5.0 to 15.0 V (Open collector output: 0.5 to
50 mA)
Frequency response:
ECG: ≥ 0.5 to 100 Hz (≥ –3 dB) (No
reproducibility of pace maker pulse)
◆
◆
◆
Recovery time after defibrillation
≤10 s (ECG, impedance respiration, NIBP, SpO 2 ,
temperature, IBP, thermistor respiration, FiO 2 ,
CO 2 , BIS)
PC specification
Processor: CU-191R: Intel Celeron 1.6GHz
CU-192R: Intel Core i7 1.5GHz
Storage Capacity: 16 GB
RAM: 4 GB or bigger
Operating system: Windows embedded standard 7
Safety Standard
Safety standard:
IEC 60601-1: 1988
IEC 60601-1 Amendment 1: 1991
IEC 60601-1 Amendment 2: 1995
IEC 60601-1-1: 2001
IEC 60601-1-2 Amendment 1: 2004
IEC 60601-1-1: 2000
IEC 60601-1-4: 1996
IEC 60601-1-4 Amendment 1: 1999
IEC 60601-1-6: 2010
1 2
IEC 60601-1-8: 2006* *
IEC 60601-1-9: 2007
IEC 60601-2-27: 2005
IEC 60601-2-30: 1999
3
IEC 60601-2-34: 2000*
IEC 60601-2-49: 2001
4
EN 12470-4:2000*
ISO 9919: 2005
ISO 21647: 2004
ISO 21647 Corr.1: 2005
ANSI/AAMIEC13:2002
EN ISO 14971 :2012
1
* The bedside monitor complies with IEC
60601-8:2006 except for interbed alarm.
2
* Only the “IEC standard” alarm sound complies
with clause 6.3.3.2.
3
* This monitor complies with IEC 60601-2-34:
2000 except for clauses 44.6,45.101 a) and
45.101 b).
4
* The bedside monitor complies with EN 124704:2000 only for clauses 6.2, 6.3 a), 6.5, 6.6, 6.7,
6.8, 6.9, 6.10 and 8
Type of protection against electrical shock:
CLASS I EQUIPMENT
Degree of protection against electrical
shock:
Defibrillator-proof type CF applied part (other
18
than CO)
Degree of protection against harmful ingress
of water: IPX1 (protected against vertically
falling water drops, only when the system
configuration is CU-191R or CU-192R, VL-190P
and DM-190P)
Method of cleaning and disinfecting or
sterilization: Equipment NOT suitable for
sterilization
Degree of safety of application in the
presence of FLAMMABLE ANAESTHETIC
MIXTURE WITH AIR, OR WITH OXYGEN OR
NITROUS OXIDE: Equipment not suitable for
use in the presence of FLAMMABLE
ANAESTHETIC MIXTURE WITH AIR, OR WITH
OXYGEN OR NITROUS OXIDE
Mode of operation: CONTINUOUS
OPERATION
ME EQUIPMENT type: STATIONARY type
◆
Environment
Transport and storage environment:
Temperature:
–20 to +65°C (–4 to +149°F)
–15 to +55°C (+5 to 131°F) (recording paper)
Humidity: 10 to 95% RH
Atmospheric pressure: 700 to 1060 hPa
Operating environment:
Temperature: 5 to 40°C (41 to 104°F)
SpO 2 accuracy is guaranteed at surrounding
temperature of 18 to 40°C (60 to 104°F).
Humidity: 30 to 85% RH (noncondensing)
Atmospheric pressure: 700 to 1060 hPa
Power:
Power AC/DC: If the optional SB-920P battery is
installed and there is a power failure or
interruption, the bedside monitor switches to
battery operation for three minutes (if battery
pack is fully charged)
Line voltage: AC 100 to 240 V
AC type: Switching regulator
DC type: Battery pack
Allowable power fluctuation range:
10%
Power input: 220 VA
Line frequency: 50 or 60 Hz
Battery charging current: 800 mA
Noise: Equipment used in medically used room
≤48 dBdbA
Cooling System: Natural cooling, no fan/filter
±
◆
◆
◆
6.7 kg
MDRAP18EAXAC-N1, 18.5 inch display:
466 W × 363 H × 175 D mm
4.9 kg
MDRAP21EAXAC-N1, 21.5 inch display:
537 W x 384 x 175 mm
5.8 kg
MDRAP24XAXAC-N1, 24 inch display:
582 W x 401 x 175 mm
7.4 kg
JA-690/694PA data acquisition unit:
145 W x 205 H x 190 D mm
1.8 kg (JA-690PA), 2.0 kg (JA-694PA)
AY-660/661/663/651/653/631/633P input unit:
83 W × 176 H × 145 D mm
1.3kg
AA-672/674P smart expansion unit:
38 W × 165 H × 145 D mm
0.5kg
BSM-1700 bedside monitor:
147 W x 194 H x 94 D mm
1.4 kg
AA-910P multi amp unit:
170 W x 44 H x 152 D mm (excluding cable)
0.7 kg (excluding cable)
JA-920P interface unit:
170 W x 44 H x 152 D mm (excluding cable)
0.7 kg (excluding cable)
QF series interface and IF series communication
cable:
65 W x 23 H x 44 D mm (excluding cables)
0.13 kg
RY-910PA remote controller:
45 W x 35 H x 135 D mm
0.08 kg
WS-960P recorder unit:
90 W x 70 H x 167 D mm
0.78 kg
◆
◆
Electromagnetic Emissions
For Electromagnetic Emissions, refer to the
Operator's manual.
Electromagnetic Immunity
For Electromagnetic Immunity, refer to the
Operator's manual.
Mechanical Strength
ME equipment: Portable type (impact and drop
resistance)
Electromagnetic compatibility
IEC 60601-1-2: 2001
IEC 60601-1-2 Amendment 1: 2004
Dimensions and Weight (approximate)
CU-191R/CU-192R core unit:
412 W × 322 H × 365 D mm
12.5 kg
VL-190P, LCD display unit, 19 inch display:
487 W × 348 H × 70 D mm
19
STANDARD ACCESSORIES
OPTIONAL ACCESSORIES
Bedside monitor core
CU-191R
Power cord (220-240V)
Accessory set (An accessory set must be
ordered)
Bedside monitor core
CU-192R
Power cord (220-240V)
unit,
standard
model,
1
unit,
high-end
model,
1
LCD display unit, VL-190P, 19 inch, built in alarm
indicator
Cable clamp
4
M4 x 12 screw for cable clamp
4
Docking connector cover
1
M3 x 10 screw for docking connector cover 1
Recorder module, WS-960P
Recording paper, FQW50-2-100
Thermal head cleaner pen
1
1
Y212A
Y212B
Y213A
Y213B
YO-60IY1
YO-60IY2
YO-60AY1
YO-60AY2
✓
✓
✓
✓
✓
✓
✓
✓
ECG connection cord, AHA,
K922A (JC-906PA), 3 m
SpO ² connection cord, K931
(JL-900P), 2.5 m
NIBP cuff,13 cm width, 23-33
cm range, S951D (YP-713T)
NIBP cuff, 16 cm width, 3345 cm range, S951E (YP714T)
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
When ordering Nellcor (AY-653P/651P)/Masimo
(AY-633P/631P) input unit, order accessory set
below.
Input unit, AY-661P, Nihon Kohden SpO2
None
Input unit, AY-663P, Nihon Kohden SpO2
None
Input unit, AY-653P, Nellcor SpO2
JL-650P, Nellcor SpO2 connection cord
ECG connection cord, IEC,
K922 (JC-906P),3 m
Air hose for NIBP, S902 (YN901P),3.5 m
IInput unit, AY-660P, Nihon Kohden SpO2
None
Input unit, AY-651P, Nellcor SpO2
JL-650P, Nellcor SpO2 connection cord
Model
Electrode lead, 3 electrode,
clip, IEC, K911 (BR-903P),
0.8 m
Electrode lead, 3 electrode,
clip, AHA, K911A (BR903PA), 0.8 m
1
Order code
Model
Electrode lead, 3 electrode, clip, IEC,
K911 (BR-903P), 0.8 m
ECG connection cord, IEC, K922 (JC906P),3 m
Y212C
YO-60IY3
Y212D
YO-60IY4
✓
✓
✓
✓
Air hose for NIBP, S902 (YN901P),3.5 m
NIBP cuff,13 cm width, 23-33 cm
range, S951D (YP-713T)
NIBP cuff, 16 cm width, 33-45 cm
range, S951E (YP-714T)
✓
✓
✓
✓
1
Input unit, AY-631P, Masimo SpO2
None
OPTIONS
Display
Input unit, AY-633P, Masimo SpO2
None
Bedside monitor, BSM-1763, Nihon Kohden SpO2
Side Cover
1
Bedside monitor, BSM-1753, Nellcor SpO2
Side Cover
JL-650P, Nellcor SpO2 connection cord
1
1
Bedside monitor, BSM-1733, Masimo SpO2
Side Cover
1
EIZO LCD display unit, VL-190P, 19 inch, touch
screen, with logo, built in alarm indicator
DC power cord for VL-190P, 2.8m
AC connection kit for VL-190P, YS-105P1
CANVYS LCD display, MDRAP18EAXAC-N1,
18.5 inch, touch screen, local purchase
CANVYS LCD display, MDRAP21EAXAC-N1,
21.5 inch, touch screen, local purchase
CANVYS LCD display, MDRAP24XAXAC-N1, 24
inch, touch screen, local purchase
Alarm indicator, YL-920P
Alarm indicator basement for CANVYS 18.5,
21.5 inch, 6143013513
Alarm indicator basement for CANVYS 24 inch,
6143903010
Stand base for 18.5 inch, 21.5 inch and 24 inch
CANVYS display, OP-MED-TF, local purchase
Display expansion board, YS-104P5, for third
display
Cables (core unit – display)
Composite cable, YS-105P2, 2.8m, for VL-190P
Composite cable, YS-105P3, 5m, for VL-190P
Composite cable, YS-105P4, 10m, for VL-190P
Branch cable (DSS), YS-105P9, 0.9m, for
CANVYS display w/o alarm indicator
Branch cable (DSS), YS-106P0, 2.8m, for
20
CANVYS display w/o alarm indicator
Branch cable (DSS), YS-106P1, 5m, for
CANVYS display w/o alarm indicator
Branch cable (DSSA), YS-106P7, 0.9m, for
CANVYS display with alarm indicator
Branch cable (DSSA), YS-106P8, 2.8m, for
CANVYS display with alarm indicator
Branch cable (DSSA), YS-106P9, 5m, for
CANVYS display with alarm indicator
Data Acquisition Unit
Data Acquisition Unit (DAU), JA-690PA, without
MULTI connector
Data Acquisition Unit (DAU), JA-694PA, with 4
MULTI connectors
Unit connection cable, YS-107P1, 1m, cable for
core unit and DAU
Unit connection cable, YS-107P2, 3m, cable for
core unit and DAU
Unit connection cable, YS-107P3, 5m, cable for
core unit and DAU
Unit connection cable, YS-107P4, 10m, cable for
core unit and DAU
Input unit
Input unit, AY-660P, 1 MULTI connector
(IBP/CO 2 ), Nihon Kohden SpO 2 , 1 x Temp, no
ECG/BP out
Input unit, AY-661P, 1 MULTI connector, Nihon
Kohden SpO 2
Input unit, AY-663P, 3 MULTI connectors, Nihon
Kohden SpO 2
Input unit, AY-651P, 1 MULTI connector, Nellcor
SpO 2
Input unit, AY-653P, 3 MULTI connectors, Nellcor
SpO 2
Input unit, AY-631P, 1 MULTI connector, Masimo
SpO 2
Input unit, AY-633P, 3 MULTI connectors,
Masimo SpO 2
Smart unit, AA-672P, 2 MULTI connectors
Smart unit, AA-674P, 4 MULTI connectors
Memory unit, QM-600P, for storing data in the
AY-600 series input unit
Multi amp unit, AA-910P, 4 MULTI connectors
Bedside monitor, BSM-1763, 3 MULTI
connectors, Nihon Kohden SpO 2
Bedside monitor, BSM-1753, 3 MULTI
connectors, Nellcor SpO 2
Bedside monitor, BSM-1733, 3 MULTI
connectors, Masimo SpO 2
Modules & units
Recorder
Recorder module, WS-960P
Recorder cable, YS-107P9, 1m
Recorder cable, YS-108P0, 3m
Recorder cable, YS-108P1, 5m
Recorder cable, YS-108P2, 10m
Optional software
esCCO program, QP-192P
esCCO/Hemodynamics review program, QP193P
Network
Network isolation unit, QW-100Y (HIT-100)
Network connection cable, YS-089P7, for core
unit and HIT-100
Wireless LAN
Wireless LAN station, QI-320PA
Wireless LAN access point, YS-095
Wireless LAN connection cable, YS-104P9
Stand & wall mount
Base stand, DM-190P
Wall mount kit, KG-190P
Cart, KC-190P
Unit holder, DH-190P
IF holder, DH-191P
QI holder, DH-192P
Base for DAU, DH-691P
Holder for DAU, DH-692P
Wall mount adapter for DAU, DH-693P
Mount adapter for GF-210/220R, DH-220P
Unit mount for GF-210R/220R with cart, DH-223P
Wall mount adapter for GF-210R/220R, DH-221P
Interface unit
Interface unit, JA-920P
EJA connection cable, YS-107P5,
920P and core unit
EJA connection cable, YS-107P6,
920P and core unit
EJA connection cable, YS-107P7,
920P and core unit
EJA connection cable, YS-107P8,
920P and core unit
1m, for JA3m, for JA5m, for JA10m, for JA-
Other option
SSD expansion board, YS-105P
Battery pack, SB-920P, X162
Upgrade software, QS-066PK
Remote controller, RY-910PA
Touch pen, Y075
BIS processor, QE-910P
Connection cable for QE-910P, YJ-671P
Neuro unit, AE-918P
Multi-gas unit, GF-110PA
Multi-gas/Flow unit, GF-120PA
Multi-gas Unit, GF-210R
Multi-gas/Flow unit, GF-220R
Connection cable for GF-210/220R, YJ-600P
(K977), 0.3 m
Connection cable for GF-210/220R, YJ-601P
(K978), 2.5 m
Sidestream CO 2 unit, AG-400RA/RK
21
Interface cable for external devices
Manufacture
Category
Model
Interface
cable
Heinen+ Lowenstein
Anesthesia
machine
Leon Plus
IF-918P
Drager Medical
Anesthesia
machine
Fabius GS/Fabius GS premium/Fabius Tiro/Fabius
plus, Primus, Primus Infinity Empowered, Apollo,
Pallas
IF-920P
FLOW-i
IF-932P
MAQUET
Covidien
Edwards
Pulsion
Covidien
Merck & Co., Inc./MSD
Covidien
Masimo
Nihon Kohden
Hospira
Radiometer
Radiometer
Anesthesia
machine
BIS monitor
CCO monitor
CCO monitor
Cererebral/somatic
oximeter
Neuromuscular
transmission
monitor
Pulse oximeter
Pulse oximeter
Sidestream CO2
SO2/CCO monitor
Transcutaneous
monitor
Transcutaneous
monitor
A-2000, BIS VISTA, BIS VIEW
Vigilance/Vigilance /Vigileo
PiCCO plus/PiCCO2
QF-902P
QF-903P
QF-911P
INVOS 5100C
IF-937P
TOF-Watch SX
QF-909P
Nellcor OxiMax N-600x
Radical, Radical-7, Radical-8, Radical-87
AG-400RK
Q2/Q2Plus/Q-VUE
IF-919P
IF-925P
QF-905P
IF-922P
MicroGas 7650 rapid
IF-913P
TCM4/TCM40/TCM Combi M
IF-914P
Ⅱ
Drager Medical
Ventilator
Covidien
MAQUET
Newport Medical
Instruments
Ventilator
Ventilator
Evita 2/Evita 2 dura/Evita 4/Evita
XL/Savina/Savina 300
Puritan Bennett 740/760/840
Servo-i/Servo-s
Ventilator
e360/e500
Hamilton Medical
Covidien
Drager Medical
Metran
QF-901P
QF-907P
QF-908P
IF-916P
HAMILTON-G5/GALILEO/HAMILTONC3/HAMILTON-C2/RAPHAEL
Ventilator
Puritan Bennett 7200
Ventilator
Babylog
Ventilator
R100/Calliope
External device which outputs analog voltage signal
Ventilator
α
IF-917P
IF-923P
IF-928P
IF-938P
IF-912P
The list is continuously increasing. Please contact your Nihon Kohden representative for updated list.
22
CONSUMABLES
ECG and Respiration (Impedance)
Cable/cord
K911 Electrode lead, BR-903P, for 3 electrodes,
clip, IEC, 0.8 m
K911A Electrode lead, BR-903PA, for 3
electrodes, clip, AHA, 0.8 m
K910A Electrode lead, BR-913P, for 3
electrodes, snap, IEC, 0.8 m
K910B Electrode lead, BR-913PA, for 3
electrodes, snap, AHA, 0.8 m
K911A Electrode lead, BR-903PA, for 3
electrodes, clip, AHA, 0.8 m
K910A Electrode lead, BR-913P, for 3 electrodes,
snap, IEC, 0.8 m
K910B Electrode lead, BR-913PA, for 3 electrodes,
snap, AHA, 0.8 m
K916 Electrode lead, BR-963P, for 3 electrodes on
one lead, clip, IEC, 0.8 m
K912 Electrode lead, BR-906P, for 6 electrodes,
clip, IEC, 0.8 m
K912A Electrode lead, BR-906PA, for 6 electrodes,
clip, AHA, 0.8 m
K915 Electrode lead, BR-916P, for 6 electrodes,
snap, IEC, 0.8 m
K915A Electrode lead, BR-916PA, for 6 electrodes,
snap, AHA, 0.8 m
K922 ECG connection cord, JC-906P, 3/6
electrodes, IEC, 3 m
K922A ECG connection cord, JC-906PA, 3/6
elec- trodes, AHA, 3 m
K925 ECG connection cord, JC-916P, 3/6
electrodes, IEC, 1.5 m
K921 ECG connection cord, JC-900P, 10
electrodes, IEC, 3 m, use with disposable electrode
with lead
K921A ECG connection cord, JC-900PA, 10
elec- trodes, AHA, 3 m, use with disposable
electrode with lead
K901 ECG patient cable, BJ-900P, 10 electrodes,
IEC, 3.8 m
K901A ECG patient cable, BJ-900PA, 10
electrodes, AHA, 3.8 m
K974 ECG/BP output cable, YJ-910P, 5 m
K975 ECG/BP output cable, YJ-920P, 0.3 m
Disposable electrodes (Vitrode series)
G203 L-150, for general use, 30 electrodes × 5/set,
35 mm dia, Vitrode L
G207 L-150X, for general use, X-ray (radiolucent),
30 electrodes × 5/set, 35 mm dia, Vitrode L
G210D F-150M, for infant/neonate to adult, 3 electrodes × 50/set, 25 × 45 mm, Vitrode F
G210C F-150S, for NICU, 3 electrodes × 50/set,
18 ×36 mm, Vitrode F
G221 G-600, for ICU/OR, 30 electrodes × 20/set,
47 × 47 mm, Vitrode G
G272A V-090M3, for general use, 3 electrodes ×
30/ set, DIN, 25 × 45 mm, Vitrode V
G272B V-040M4, for general use, 4 electrodes ×
10/ set, DIN, Vitrode V
G278A V-09IO3, for general use, 3 electrodes ×
30/ set, DIN, 25 × 45 mm, Vitrode V
G273A V-04IO4, for general use, 4 electrodes ×
10/ set, DIN, 25 × 45 mm, Vitrode V
G272C V-060M6, for general use, 6 electrodes ×
10/ set, DIN, Vitrode V
G274A V-06IO6, for general use, 6 electrodes ×
10/ set, DIN, 25 × 45 mm, Vitrode V
G271A V-120S3, for NICU, 3 electrodes × 40/set,
DIN, 20 × 20 mm, Vitrode V
G300A N-031S3, for NICU, 3 electrodes x 10/set,
DIN, Vitrode N
Respiration (thermistor method)
P901 Thermistor respiration pickup for nose, TR900P
P902 Thermister respiration pickup for airway, TR910P
V911 Airway adapter, YG-001P
SpO2
SpO 2 Cord
K931 SpO 2 connection cord, JL-900P, 2.5 m
Y094A Dual SpO2 adapter, JL-500P2, 2.5 m
K935 Nellcor SpO2 connection cord, JL-650P, 3 m
K936 Masimo SpO 2 connection cord, for LNOP
series, JL-630P, 3.6 m
K937 Masimo SpO 2 connection cord, for LNCS
series, JL-631P, 3 m
Probes (BluPRO series)
P225F Finger probe, TL-201T, attached to finger
or toe by clip
P311C Finger probe, TL-631T3, regular size,
attached to finger or toe by tape
P310C Finger probe, TL-630T3, large size,
attached to finger or toe by tape
P225G Multi-site probe, TL-220T, attached to
finger or toe by tape
P259 Cottony tape, 340703, secures probe and
cord for stable monitoring, stretchable, 20
pcs/set
P267 Probe fastener, 30 pcs/set
Reusable Probe
TL-651T3 Finger-tip type, 40 kg or more
Disposable probes (BluPRO series)
P203A TL-271T, for adult finger or toe, 24
pcs/set, 0.8 m
P204A TL-271T, for adult finger or toe, 5 pcs/set,
0.8 m
P203E TL-271T3, for adult finger or toe, 24
pcs/set, 1.6 m
P204E TL-271T3, for adult finger or toe, 5
pcs/set, 1.6 m
P203B TL-272T, for child finger or toe, 24
pcs/set, 0.8 m
P204B TL-272T, for child finger or toe, 5 pcs/set,
0.8 m
P203F TL-272T3, for child finger or toe, 24
pcs/set, 1.6 m
P204F TL-272T3, for child finger or toe, 5
pcs/set, 1.6 m
P203C TL-273T, for neonate instep, 24 pcs/set,
0.8 m
P204C TL-273T, for neonate instep, 5 pcs/set,
0.8 m
P203G TL-273T3, for neonate instep, 24 pcs/set,
23
1.6 m
P204G TL-273T3, for neonate instep, 5 pcs/set,
1.6 m
P203D TL-274T, for infant finger or toe, 24
pcs/set, 0.8 m
P204D TL-274T, for infant finger or toe, 5
pcs/set, 0.8 m
P203H TL-274T3, for infant finger or toe, 24
pcs/set, 1.6 m
P204H TL-274T3, for infant finger or toe, 5
pcs/set, 1.6 m
Multi-site Y probe
P205A Multi-site Y probe, TL-260T (for adult,
child, neonate), 5 pcs/set
P260A Sponge attachment tape S for TL-260T
multi-site Y probe, 24 pcs/set
P260B Sponge attachment tape L for TL-260T
multi-site Y probe, 24 pcs/set
P256 Ear clip adapter for TL-260T, reusable
Disposable probes
P228A TL-051S, for adult/neonate, 5 pcs/set,
0.8 m cable
P228B TL-052S, for adult/neonate, 5 pcs/set,
1.6 m cable
P229A TL-061S, for child/infant, 5 pcs/set, 0.8
m cable
P229B TL-062S, for child/infant, 5 pcs/set, 1.6
m cable
P260C Foam tape, for TL051S/052S/061S/062S, 100 pcs
Nellcor SpO 2 probes are available from
NELLCOR (www.nellcor.com) or their suppliers
Masimo SpO 2 probes are available from
MASIMO (www.masimo.com) or their suppliers
NIBP
Reusable Cuffs (Latex free)
S943A YP-960T: for infant, 5 cm cuff width
S943B YP-961T: for child, 7 cm cuff width
S943C YP-962T: for child, 10 cm cuff width
S944B YP-963T: for adult, 13 cm cuff width
S944C YP-964T: for adult, 15 cm cuff width
S944D YP-965T: for thigh, 19 cm cuff width
Reusable Cuffs (YAWARA-CUFF 2 series,
Latex free)
S951A YP-710T: for infant, 5 cm cuff width
S951B YP-711T: for child, 7 cm cuff width
S951C YP-712T: for adult small, 10 cm cuff
width
pcs
S945D YP-811P: for child, 8 cm cuff width, 20
pcs
S946E YP-812P: for adult, 10 cm cuff width, 20
pcs
S946F YP-813P: for adult, 14 cm cuff width, 20
pcs
S946G YP-814P: for adult, 15 cm cuff width, 20
pcs
S946H YP-815P: for adult, 17 cm cuff width, 20
pcs
S946I YP-816P: for adult, 18 cm cuff width, 20
pcs
S946J YP-817P: for thigh, 20 cm cuff width, 20
pcs
S948A YP-820P: for neonate, 2 cm cuff width,
10 pcs
S948B YP-821P: for neonate, 3 cm cuff width,
10 pcs
S948C YP-822P: for neonate, 4 cm cuff width,
10 pcs
S948D YP-823P: for neonate, 4.5 cm cuff width,
10 pcs
S948E YP-824P: for neonate, 5 cm cuff width,
10 pcs
Air hoses
S903 YN-990P: extension hose, 1.5 m
S901 YN-900P: 1.5 m
S902 YN-901P: 3.5 m
S904 YN-920P: for neonate, 1.5 m
S905 YN-921P: for neonate, 3.5 m
IBP
Argon Medical Devices:
K951 IBP connection cord, JP-900P, Argon
Medical Devices blood pressure transducers are
available from Argon Medical Devices
(www.argonmedical.com) or their supplier.
Edwards Lifesciences:
L901 IBP connection cord, JP-920P, for
Edwards Lifesciences transducer, 3.5 m
Edwards Lifesciences blood pressure
transducers are available from Edwards
Lifesciences Corporation (www.edwards.com) or
their suppliers.
Biosensors International:
K957 IBP connection cord, JP-960P, for
Biosensor transducer, 3.5 m
Biosensors blood pressure transducers are
available from BIOSENSORS INTERNATIONAL
(www.biosensorsintl.com) or their suppliers.
Others:
K952 IBP connection cord, JP-910P
S951D YP-713T: for adult, 13 cm cuff width
S951E YP-714T: for adult large, 16 cm cuff
width
S951F YP-715T: for thigh, 19 cm cuff width
Disposable Cuffs
S945C YP-810P: for infant, 6 cm cuff width, 20
Temperature
K961 Temperature connection cord, JT-900P, 30
cm
Thermistor Probe
24
P240B For adult rectum/esophagus, 401J
P241B For child rectum/esophagus, 402J
FiO2
P242D Disc type, 409J
K941 FiO 2 connection cord, JO-900P, 3 m
P249A Probe cover, for 401J, 10 pcs/set
P911 O 2 sensor, 074705, 0.6 m
P252 Temperature insulation pad, for 409J, 60
pcs/set
V912 T-shaped adapter, 110774
CO2 (Mainstream measurement)
Semi-quantitative method
P903 CO 2 sensor kit, TG-900P (TG-101T + JG900P), 3 m
P922A CO 2 sensor, TG-101T, 1 m
K981 CO 2 adapter, JG-900P, 2 m
R801 Airway adapter, YG-101T, 50 pcs/set
P907 CO 2 sensor kit, TG-920P (TG-121T + JG920P), 3.5 m
P923 CO 2 sensor, TG-121T, 2 m
K984 CO 2 adapter, JG-920P, 1.5 m
R804 Airway adapter, YG-111T, 30 pcs/set
V922 Nasal adapter, YG-121T, for nasal/oral, 30
pcs/set
V923 Nasal adapter, YG-122T, for nasal/oral, 30
pcs/set, with O2 supply tube adapter
V927 Oxygen cannula, 25 pcs/set
Quantitative method
P909 CO 2 sensor kit, TG-970P (TG-221T + JG970P), 3.5 m
CO
K962 CO connection cord, JT-950P, 2.0 m
Argon Medical Devices:
Argon Medical Devices injectate supply systems
and thermodilution catheters are available from
Argon Medical Devices
(www.argonmedical.com) or their supplier.
Edwards Lifesciences:
Edwards Lifesciences injectate supply systems
and thermodilution cathetes are available from
Edwards Lifesciences (www.edwards.com).
Gas monitoring
GF-110PA/120PA
V915A Dryline A-Adult, water trap, 613712, 10
pcs/set
V915B Dryline N-Neonate, water trap, 6137, 10
pcs/set
V916A T-piece S-Straight, 613739, 10 pcs/set
V916B T-piece E-Elbow, 613748, 10 pcs/set
V903F T-piece, for neonate, 618877, 25 pcs/set
P924 CO 2 sensor, TG-221T, 3 m
V917C Sampling tube, Adult, 25 pcs/set
K987 CO 2 adapter, JG-970P, 0.5 m
V917D Sampling tube, Neonate, 25 pcs/set
R805 Airway adapter, adult YG-211T, 30 pcs/set
R806 Airway adapter, child/neonate, YG-213T,
30 pcs/set
R807 Airway adapter, pediatric, YG-214T, 30
pcs/set
CO2 (Sidestream measurement)
V901 Exhaust gas adapter, 1pc
FilterLine
TM
H set, 25 pcs/set
V908D Adult/child
V908E Adult/child
V908F Infant/neonate
CapnoLine
TM
H set, 25 pcs/set
Exhaust gas adapter, 6144-008197A
GF-210R/220R
V918 Water trap, YG-600P, 12 pcs/set
V920A T-piece S-Straight, YG-620P, 25 pcs/set
V920B T-piece E-Elbow, YG-621P, 25 pcs/set
V919 Sampling line, YG-610P, 3.0 m, 25 pcs/set
Flow/Paw
GF-120PA/220R
P913 Flow adapter, TF-120P
P914 Flow tube, YF-120P, 5 pcs/set
P915 Luer cap, YS-094PO, 10 pcs/set
V909D Adult
V909E Child
V909F Infant/neonate
Respiration (thermistor)
EEG
L461 EEG connection cord, JE-905P, 2 ch, 3 m
P901 Respiration pickup, TR-910P, for nose
L462 EEG connection cord, JE-906P, 8 ch, 3 m
P902 Respiration pickup, TR-910P, for airway
H503A EEG disk electrode, NE-113A, 26 pcs/set,
1.5 m, DIN
V911 Airway adapter, YG-001P
25
H503 EEG disk electrode, NE-114A, 26 pcs/set,
0.8 m, DIN
H527 EEG collodion electrode, NE-136A, 12
pcs/set, 0.7 m, DIN
H537A EEG needle electrode, NE-224S, 20
pcs/set, 1.5m, DIN
H471 Disk electrode, BE-910P, 0.8 m
H472 Collodion electrode, BE-920P, 0.8 m
K461 EEG electrode lead, BE-930P, 0.8 m
F507 EEG paste, Z-181BE, 180 g tube x 2/box,
ELEFIX
BIS
BIS sensors are available direct from Covidien
(www.covidien.com) or their suppliers
APCO
FloTrac sensors are available direct from
Edwards Lifescience (www.edwards.com) or
their suppliers
Recording
A721 Recording paper, FQW50-2-100, 10
pcs/set, 50 mm x 20 m
Y011 Thermal head cleaning pen, 5 pcs/set
26