BoxRail and RaceRail | Ceiling Cable | LED | 107
Remote Power Housing | Canopy & Rail Hub Installation Instructions
Please read instructions in their entirety before proceeding with any part of the installation. This luminaire must be installed in accordance with the National Electric
Code and local regulations. This luminaire must be installed by a qualified electrician. Use of ballast or other components not supplied by Vode Lighting voids
warranty. To prevent electric shock, turn off electricity at the fuse box before proceeding. Do not install this product in wet locations. UL listed for dry and damp
locations only. Retain instructions for future reference.
Technical Support: 707-996-9898
remote power housing
flex conduit
(provided by others)
Installation Instructions:
Small and Large Canopy Assemblies
junction box
(provided by others)
wire harness
(18 gauge)
universal mounting plate
(small canopyorientation shown)
2 conductor power cord
(22 gauge)
strain relief
1. Install Remote Power Supply and Junction Box
IMPORTANT! Before installing power supply turn off electricity at fuse
box and consult wiring diagram. When mounting junction box, refer to
system layout center to center locations. Mount junction box and remote
power supply housing, feeding wire harness through junction box to power
supply. Junction box, conduit and conduit adapters provided by others.
2. Install Universal Mounting Plate and Drywall
For small canopy
Install universal mounting plate to junction box using screws provided and
with protrusion facing out. Install 5/8" drywall. End of universal mounting
plate protrusion should be flush with drywall.
For large canopy:
Install 5/8" drywall. Install universal mounting plate with screws provided
and with protrusion facing in.
3. Preparing Ceiling Cable Hardware
Push the cord gripper from the suspension disk and pull suspension cord
through the disk until the specified installation length is reached. Release
the cord gripper once desired length is reached.
4. Fasten Wire Harness Connectors
Firmly fasten male and female wire harness connectors, as shown. Push
remaining cord inside junction box.
5. Securing Suspension Disk
Push suspension disk into universal mounting plate. Secure the suspension
cord by tightening the hex screw on the side of the suspension disk
protrusion, as shown.
suspension disk
small canopy
(same for large canopy)
6. Secure Canopy
Slide canopy up suspension cord, magnets located on the suspensions disk
will secure canopy in place. Check alignment of system after final
installation and if necessary, remove canopy to loosen hex screw to readjust cord to level the system.
Rail to Hub/Coupler:
1. Install Rail to Hub.
2. Tighten set screw to lock rail to hub/coupler.
BoxRail hub
© Copyright 2014. All ideas, arrangements, and plans indicated or represented by the above drawings, are the property of Vode Lighting LLC. and were created, evolved and developed for use on and in concoction with the specified
project. No part of the above drawing, design, arrangements or ideas thereon shall be duplicated or used for any purpose whatsoever without the express permission of Vode Lighting LLC. Vode Lighting LLC 1206 East MacArthur
June 9, 2014
St. #3 SOnoma, CA 95476 707.996.9898
BoxRail and RaceRail | Ceiling Cable | LED | 107
Remote Power Housing | Canopy & Rail Hub Installation Instructions
Step 1: Install Remote Power Supply and Junction Box
Step 2: Install Universal Mounting Plate and Drywall
IMPORTANT! Before installing remote power supply turn off electricity at fuse
For small canopy
Install universal mounting plate to junction box using screws provided and with
protrusion facing out. Install 5/8" drywall. End of universal mounting plate protrusion
should be flush with drywall.
For large canopy:
Install 5/8" drywall. Install universal mounting plate with screws provided and with
protrusion facing in.
box & consult wiring diagram. When mounting junction box, refer to system
layout center to center locations. Mount junction box and remote power supply
housing, feeding wire harness through junction box to power supply. Junction box,
conduit and conduit adapters provided by others.
For installation of universal mounting plate
before drywall. For use with small canopy
For installation of universal mounting plate
after drywall. For use with large canopy
For use with small canopy
For use with large canopy
Step 3: Preparing Ceiling Cable Hardware
Step 4: Fasten Wire Harness Connectors
Push the cord gripper from the suspension disk and pull suspension cord through the
disk until the specified installation length is reached. Release the cord gripper once
desired length is reached. Position strain relief 6" from the suspension disk. Tighten the
set screw on the strain relief.
IMPORTANT: Vode small canopy mounting hardware designed for 5/8" drywall.
Accurate placement and alignment of junction boxes is critical as it will determine the
line of entire system. Refer to system layout for mounting locations.
Firmly fasten male and female wire harness connectors, as shown. Push remaining cord
inside junction box.
strain relief
6"
For use with small canopy
push here to release grip
on cord, adjust length
For use with large canopy
5/8" drywall
Step 5: Securing Suspension Disk
Step 6: Secure Canopy
Push suspension disk into universal mounting plate. Secure the suspension cord by
tightening the hex screw on the side of the suspension disk protrusion, as shown.
Slide canopy up suspension cord, magnets located on the suspensions disk will secure
canopy in place. Check alignment of system after final installation and if necessary, remove
canopy to loosen hex screw to re-adjust cord to level the system.
For use with small canopy
For use with large canopy
To release suspension disk,
push tab and pull disk out.
small canopy
large canopy
BoxRail and RaceRail | Ceiling Cable | LED | 107
Rail Installation Instructions
Please read instructions in their entirety before proceeding with any part of the installation. This luminaire must be installed in accordance with the National Electric
Code and local regulations. This luminaire must be installed by a qualified electrician. Use of ballast or other components not supplied by Vode Lighting voids
warranty. To prevent electric shock, turn off electricity at the fuse box before proceeding. Do not install this product in wet locations. UL listed for dry and damp
locations only. Retain instructions for future reference.
Technical Support: 707-996-9898
BoxRail hub
Red warning disks indicate
non-powered end of rail
BoxRail coupler
Green PCB boards indicate
powered end of rail
© Copyright 2014. All ideas, arrangements, and plans indicated or represented by the above drawings, are the property of Vode Lighting LLC. and were created, evolved and developed for use on and in concoction with the specified
project. No part of the above drawing, design, arrangements or ideas thereon shall be duplicated or used for any purpose whatsoever without the express permission of Vode Lighting LLC. Vode Lighting LLC 1206 East MacArthur
June 9, 2014
St. #3 SOnoma, CA 95476 707.996.9898
BoxRail and RaceRail | Ceiling Cable | LED | 107
Rail Installation Instructions
note: Vode typically supplies one driver per rail
DRIVER
DRIVER
DRIVER
~ 2.01"
Typ. Center-to-Center
Typ. Center-to-Center
~ 1.98"
Typ. Center-to-Center
2' rails = 24"
2' rails = 24"
2' rails = 24"
3' rails = 36"
3' rails = 36"
3' rails = 36"
4' rails = 48"
4' rails = 48"
4' rails = 48"
5' rails = 60"
5' rails = 60"
5' rails = 60"
6' rails = 72"
6' rails = 72"
6' rails = 72"
install BoxRail to coupler
install BoxRail to hub
install BoxRail to hub
tighten set screw to lock
rail to hub/coupler
tighten set screw to lock
rail to hub/coupler
tighten set screw to lock
rail to hub/coupler
power fed through pins of hubs and
couplers to green PCB boards on rails
Couplers have 1 power
feed side and 1
non-powered side