Honeywell
SmartLine
Technical Information
STR700 SmartLine Remote Diaphragm Seals
Specification 34-ST-03-104
Introduction
Part of the SmartLine® family of products, the STR700 is
suitable for monitoring, control and data acquisition.
STR700 products feature piezoresistive sensor
technology combining pressure sensing with on chip
temperature compensation capabilities providing high
accuracy, stability and performance over a wide range of
application pressures and temperatures.
The SmartLine family is also fully tested and compliant
with Experion ® PKS providing the highest level of
compatibility assurance and integration capabilities.
SmartLine easily meets the most demanding application
needs for pressure measurement applications
Best in Class Transmitter Features:
•
Accuracies up to 0.075% standard
•
Automatic static pressure & temperature
Figure 1 - STR700 Remote Diaphragm Seal Unit
compensation
Typical Diaphragm Seal applications
•
Rangeability up to 100:1
•
High Process Temperatures
•
Local display capabilities
•
Viscous or Suspended Solids
•
External zero, span, & configuration capability
•
Highly Corrosive Process Materials
•
Polarity insensitive electrical connections
•
Sanitary Applications
•
Comprehensive on-board diagnostic capabilities
•
Applications with Hydrogen Permeation Possibilities
Integral Dual Seal design for highest safety based on
•
Level Applications with Maintenance Intensive Wet
•
Legs
ANSI/NFPA 70-202 and ANSI/ISA 12.27.0
World class overpressure protection
•
Applications requiring remote Transmitter Mounting
•
Full compliance to SIL 2/3 requirements.
•
Tank Applications with Density or Interface
•
Modular design characteristics
•
Available with 15 year warranty
•
Measurements
Communications/Output Options:
Remote Seal/Transmitter Span & Range Limits:
Model
psid (bar)
psid (bar)
psid (bar)
psid (bar)
100 (7.0)
-100 (-7.0)
100 (7.0)
1 (0.07)
Model
psig (bar)
psig (bar)
psig (bar)
psig (bar)
STR74G
500 (35.0)
-500 (-35.0)
500 (35.0)
5 (035)
STR73D
•
Honeywell Digitally Enhanced (DE)
•
HART ® (version 7.0)
•
FOUNDATION™ Fieldbus
All transmitters are available with the above listed
communications protocols.
По вопросам продаж и поддержки обращайтесь:
Астана +7(7172)727-132, Волгоград (844)278-03-48, Воронеж (473)204-51-73, Екатеринбург (343)384-55-89, Казань (843)206-01-48,
Краснодар (861)203-40-90, Красноярск (391)204-63-61, Москва (495)268-04-70, Н иж ний Н овгород (831)429-08-12, Н овосибирск (383)227-86-73,
Ростов-на-Дону (863)308-18-15, Самара (846)206-03-16, Санкт-Петербург (812)309-46-40, Саратов (845)249-38-78, Уфа (347)229-48-12
Единый адрес: hw n@ nt-rt.ru
www.honeywell.nt-rt.ru
2
STR700 Smart Pressure Transmitter
Description
The SmartLine family pressure transmitters are designed
around a high performance piezo-resistive sensor. This
one sensor actually integrates multiple sensors linking
process pressure measurement with on-board static
pressure (DP Models) and temperature compensation
measurements. This level of performance allows the ST
700 to replace most competitive transmitters available
today.
Indication/Display Option
Personal Computer Configuration
Honeywell’s SCT 3000 Configuration Toolkit provides an
easy way to configure Digitally Enhanced (DE) instruments
using a personal computer as the configuration interface.
Field Device Manager (FDM) Software and FDM Express
are also available for managing HART & Fieldbus device
configurations.
System Integration
о
SmartLine communications protocols all meet the
The ST 700 modular design accommodates a basic
most current published standards for
alphanumeric LCD display.
HART/DE/Fieldbus.
Basic Alphanumeric LCD Display Features
о
Integration with Honeywell’s Experion PKS offers the
following unique advantages,
о
Modular (may be added or removed in the field)
о
0, 90,180, & 270 degree position adjustments
о Tamper reporting
о
Pa, KPa, MPa, KGcm2, Torr, ATM, i4H20 , mH20 ,
о
bar, mbar, inH20 , inHG, FTH20 , mmH20 , mm HG,
о All ST 700 units are Experion tested to provide
& psi measurement units
FDM Plant Area Views with Health summaries
the highest level of compatibility assurance
о
2 Lines 16 Characters (4.13H x 1.83W mm)
о
Square root output indication
(V )
Diagnostics
SmartLine transmitters all offer digitally accessible
diagnostics which aid in providing advanced warning of
possible failure events minimizing unplanned shutdowns,
providing lower overall operational costs
Configuration Tools
Integral Three Button Configuration Option
Suitable for all electrical and environmental requirements,
SmartLine offers the ability to configure the transmitter
and display via three externally accessible buttons when
a display option is selected. Zero/span capabilities are
also optionally available via these buttons with or without
selection of the display option.
Hand Held Configuration
SmartLine transmitters feature two-way communication and
configuration capability between the operator and the
transmitter. This is accomplished via Honeywell’s field­
rated Multiple Communication Configurator (MCT202).
The MCT202 is capable of field configuring DE and HART
Devices and can also be ordered for use in intrinsically safe
environments. All Honeywell transmitters are designed and
tested for compliance with the offered communication
protocols and are designed to operate with any properly
validated hand held configuration device.
Modular Design
To help contain maintenance & inventory costs, all ST 700
transmitters are modular in design supporting the user’s
ability to replace meter bodies, add indicators or change
electronic modules without affecting overall performance or
approval body certifications. Each meter body is uniquely
characterized to provide in-tolerance performance over a
wide range of application variations in temperature and
pressure and due to the Honeywell advanced interface,
electronic modules may be swapped with any electronics
module without losing in-tolerance performance
characteristics.
Modular Features
о
Meter body replacement
о
Exchange/replace electronics/comms modules*
о
Add or remove integral indicator*
о
Add or remove lightning protection (terminal
connection)*
* Field replaceable in all electrical environments (including
IS) except flameproof without violating agency approvals.
With no performance effects, Honeywell’s unique
modularity results in lower inventory needs and lower
overall operating costs.
STR700 Smart Pressure Transmitter
3
Performance Specifications1
Reference Accuracy2(conformance to +/-3 Sigma)
Model
STR73D
STR74G
URL
100 psid/7.0 bar
500 psi/35 bar
LRL
-100 psi/-7.0bar
-14.7 psi/-1.0 bar
Maximum
Turndown
Ratio
100:1
100:1
Min Span
9 psi/.07bar
5 psi/.035 bar
Reference
Accuracy1
(% Span)
0.075
0.075
Zero and span may be set anywhere within the listed (URL/LRL) range limits
A c cu racy1
(% o f S p a n )
T e m p e ra tu re Effect *
(%Span/50°F)
Turn d ow n
M odel
STR73D
URL
100 psi/7 .0 bar
STR74G 500 psig/35 bar
A
В
g re a te r than
С
psi(bar)
27.7:1
0.0250
0.050
3.61 (0.249)
25:1
0.0250
0.050
20 (1.4)
E
0.028
1.200
A + в [ —
^ Span
1
)
% Span
psi(bar)
7.2 (0.50)
T e m p Effec:t
Turn D ow n Effect
±
F
D
±
f
F '
D + E -------. Span
<k Span per 28°C 50° F)
Accuracy at Specified Span, Temperature and Static Pressure: (conformance to +/-3 Sigma)
Total Performance (% of Span):
Total Performance = +/- V( Accuracy)2 + (Temp Effect)2
Total Performance Examples: (5:1 Turndown, up to 50 °F shift)
STR73D @ 20 psid: 1.03% of span
Typical Calibration Frequency:
Calibration verification is recommended every four (4) years
Notes:
1 .Terninal Based A ccuracy - Includes com bined effects of linearity, hysteresis, and repeatability. Analog output adds 0.005% of span.
2. For zero based spans and reference conditions of 25°C (77°F), 0 psig static pressure, 10 to 55% R.H, and 316S tainless Steel barrier diaphragm s
3. Specification applies to transm itter w ith 2 seals. A pply a factor of 1.5 for tem perature effect of ca pilla ry lengths greater then 10 feet.
4
STR700 Smart Pressure Transmitter
Operating Conditions - All Models
Ambient Temperature1
Humidity
Rated Condition
Reference
Condition (at
zero static)
Parameter
°F
°c
°F
°c
°F
°c
°F
25±1
77 ±2
-
-
-
-
-55 to 90
-67 to 194
10 to 55
0 to 100
Vacuum Region, Minimum
Pressure
mmHg absolute
Maximum Allowable
Working Pressure (MAWP)4
(ST 700 products are rated to
M axim um Allow able W orking
Pressure. MAW P depends on
Approval Agency and transm itter
m aterials of construction.)
Transportation and
Storage
°c
%RH
Supply Voltage, Current, and
Load Resistance
Operative Limits
0 to 100
0 to 100
Atmospheric (See Figure 4 for vacuum limitation)
10.8 to 42.4 Vdc at terminals (IS versions limited to 30 Vdc)
0 to 1,440 ohms (as shown in Figure 2)
MAWP is minimum of Body Rating or Seal Rating (See Model Selection Guide for Seal
MAWP)
Body
MAWP
STR73D
750 psig (51.7 bar) Bolted Process Heads
STR74G
500 psig (35 bar)
1 Am bient Tem perature Limit is a function of Process Interface Tem perature. (See Figures 3 & 4)
LCD Display operating tem perature -20°C to +70°C . Storage tem perature -30°C to 80°C
4 Consult factory for M AW P of ST 700 transm itters with CRN approval.
Note: A minimum of 250
ohms of loop resistance is
required to support
communications. Loop
resistance = barrier
resistance + wire resistance +
receiver resistance.
Loop
Resistance
(o hm s)
A
0
10.8
16.28 20.63 25 28.3 37.0
Operating Voltage ( Vdc)
Maximum Ambient
Temperature (°F)
= Operating Area
42.4
Run™ = 45.6 x (Power Supply Voltage - 10.8)
Figure 2 - Supply voltage and loop resistance
200
350
450
Process Interface Temperature (°F)
Figure 3 - Ambient temperature Limits
STR700 Smart Pressure Transmitter
5
Maximum Pressure Limited
Process Temperature (Degrees F)
Maximum Pressure Limited
Process I emperature (Degrees F)
Figure 4 - STR700 Remote Seals operable limits for pressure vs. temperature
6
STR700 Smart Pressure Transmitter
Performance Under Rated Conditions - All Models
Parameter
Description
Analog Output
Digital Comm unications:
Two-wire, 4 to 20 mA (HART & DE Transm itters only)
Honeywell DE, HART 7 protocol or F o u n d a t io n Fieldbus ITK 6.0.1 com pliant
All transm itters, irrespective of protocol have polarity insensitive connection.
Output Failure Modes
Honeywell Standard:
Normal Limits:
Failure Mode:
Supply Voltage Effect
Transmitter Turn on Time
(includes power up & test algorithms)
Damping Tim e Constant
NAMUR NE 43 Compliance:
3 .8 - 2 0 . 8 mA
3 .8 - 2 0 . 5 mA
s 3.6 mA and г 21.0 mA
s 3.6 mA and г 21.0 mA
0.005% span per volt.
HART or DE: 2.5 sec.
Foundation Fieldbus: Host dependant
HART: Adjustable from 0 to 32 seconds in 0.1 increments. Default: 0.50 seconds
DE: Discrete values 0, .16, .32, .48, 1, 2, 4, 8, 16, 32 seconds. Default: 0.48 seconds
Electrom agnetic Com patibility
IEC 61326-3-1
Lightning Protection Option
Leakage Current: 10uA max @ 42.4VDC 93C
Im pulse rating:
8/20uS
5000A (>10 strikes)
10/1 OOOuS
10000A (1 strike min.)
200A (> 300 strikes)
Materials Specifications (see model selection guide for availability/restrictions with various models)
Parameter
Description
Process Interface
See Model Selection Guide for M aterial Options for desired seal type.
Seal Barrier Diaphragm
316L Stainless Steel, Monel®, Hastelloy® C, Tantalum
Seal G asket M aterials
Klinger C-4401 (non-asbestos)
Mounting Bracket
Carbon Steel (Zinc-Chrom ate plated) or 304 Stainless Steel or 316 Stainless Steel.
Fill Fluid (M eter Body)
Fill Fluid (Secondary)
Electronic Housing
Capillary Tubing
Grafoil®, Teflon®, Gylon 3510®
Silicone Oil 200
S.G. @ 25°C = 0.94
CTFE (Chlorotrifluoroethylene)
S.G. @ 25°C = 1.89
Silicone Oil 200
S.G. @ 25°C = 0.94
CTFE (Chlorotrifluoroethylene)
S.G. @ 25°C = 1.89
Silicone Oil 200
Syltherm 800®
S.G. @ 25°C = 1.07
S.G. @ 25°C = 0.90
NEOBEE M-20®
S.G. @ 25°C = 0.93
Pure Polyester Powder Coated Low Copper (<0.4% )-Alum inum . Meets NEMA 4X, IP66, & P67.
All stainless steel housing is optional.
Material: Arm ored Stainless Steel or PVC Coated Arm ored Stainless Steel.
Length: 5, 10, 15, 20, 25, and 35 feet (1.5, 3, 4.6, 6.1, 7.5, and 10.7 meters).
A 2 inch (51 millimeter) S.S. close-coupled nipple is also available. See Model Selection Guide.
Refer to
F ig u r e 5 for guide to m aximum capillary length vs. diaphragm diameter.
W iring
Accepts up to 16 AW G (1.5 mm diameter)
Mounting
See Figure 6
Dimensions
Transm itter: See Figures 7a and 7b.
Net W eight
Transm itter: 8.3 pounds (3.8 Kg). W ith Alum inum Housing. Total weight is dependent on seal
Seal: See Figures 8 through 15
NOTE: Pressure transm itters that are part of safety equipm ent for the protection of piping (system s) or vessel(s) from exceeding allowable
pressure limits, (equipm ent with safety functions in accordance with Pressure Equipm ent Directive 97/23/EC article 1, 2.1.3), require
separate examination.
STR700 Smart Pressure Transmitter
7
Minimum recommended span for STR73D Transmitter with two Remote Seals
Capillary
15”
2.4
200 iwc
2.9
100 iwc
125 iwc
150 iwc
175 iwc
3.5
16 iwc
20 iwc
24 iwc
28 iwc
36 iwc
40 iwc
35'
4.1
12 iwc
15 iwc
18 iwc
21 iwc
27 iwc
30 iwc
35'
10”
о
5”
CM
Diaphragm
Size
30”
Capillary Length
Maximum
35”
5’
20'
Minimum recommended span for STR73D Transmitter with one Remote Seal
5”
2.4
20 psig
30 psig
2.9
10 psig
15 psig
20 psig
25 psig
30 psig
3.5
50 iwc
80 iwc
100 iwc
120 iwc
140 iwc
180 iwc
200 iwc
Ю
CO
Capillary
4.1
40 iwc
60 iwc
80 iwc
100 iwc
120 iwc
160 iwc
180 iwc
35'
30”
35”
Capillary
Length
10”
о
Direct
Mount
CM
Diaphragm
Size
15”
30”
35”
Capillary
Length
5’
20'
Minimum recommended span for STR74G Transmitter with one Remote Seal
Diaphragm
Size
Direct
Mount
5”
2.0
25 psig
30 psig
40 psig
2.4
10 psig
15 psig
20 psig
25 psig
30 psig
40 psig
50 psig
35’
2.9
8 psig
9 psig
10 psig
11 psig
12 psig
14 psig
15 psig
35’
3.5
5 psig
5 psig
5 psig
120 psig
140 psig
180 psig
200 psig
35’
4.1
5 psig
5 psig
5 psig
100 psig
120 psig
160 psig
180 psig
35’
10”
15”
Capillary
20”
15’
Figure 5 - Typical Maximum capillary length and diaphragm size chart
N O T E : Low er fla n g e s e a l sh o u ld n ot be m o u n te d o v e r 22 fe e t b e lo w or a b o v e
th e tra n s m itte r f o r s ilic o n e f ill flu id (11 fe e t f o r C T F E f ill flu id ) w ith ta n k at one
a tm o s p h e re . The c o m b in a tio n o f ta n k v a c u u m ana high p re s s u re c a p illa ry
h ead e f f e c t sh o u ld n ot e x c e e d 9 p si v a c u u m (3 0 0 m m H g a b s o lu te ).
C o n s u lt H o n e y w e ll fo r in s ta lla tio n o f S T R 7 3 D .
Figure 6 - STR700 transmitter with remote diaphragm seals shown mounted on a tank
8
Reference Dimensions Horizontal Mounting
STR700 Smart Pressure Transmitter
STR700 Smart Pressure Transmitter
9
Reference Dimensions Horizontal Mounting (cont’d)
LGP REMOTE SEAL
WITH HORIZONTAL PIPE MOUNT
Figure 7 — Approximate horizontal mounting dimensions for Remote Seal Transmitter
Reference Dimensions Vertical Mounting
127,0
5,00
C LEARANCE FOR
ENDCAP REMOVAL
& DISPLAY
MANIPULATION
125.9
4-96
WfTlH DISPLAY ENDCAP
OR
IT 6.0
4.57
127.0
5.00
C LEARANCE FOR
ENDCAP REMOVAL
& FIELD TERMINAL
C ONNECTIONS
WITH SOLID ENDCAP
ON ELECTRONIC S END
SEAL OMITTED
IN TH IS VIEW
FOR CLARITY
OP REMOTE SEAL
WITH VERTICAL PIPE MOUNT
SEAL OMITTED
IN T H IS VJEW
FOR CLARITT
10
STR700 Smart Pressure Transmitter
Reference Dimensions Vertical Mounting (cont’d)
- 127,0
5.00
125.9
4-96
127,0
5.00
WfTH DISPLAY ENDCAP
OR
C LEARANCE FOR
ENDCAP REMOVAL
& DISPLAY
MANIPULATION
C LEARANCE FOR
ENDCAP REMOVAL
& H ELD TERMINAL
С ONNECTIONS
116,0
4.57
WITH SOLID EN D C AP
ON ELECTRONICS END
AP REMOTE SEAL
WITH VERTICAL PIPE MOUNT
127.0
5.00
C LE AR AN C E FOR
E N D C AP REMOVAL
Sl DISPLAY
MANIPULATIO N
-
SEAL OMITTED
IN THIS VIEW
FOR CLARITY
127.0
5.00
125.9
4.96
WFTH DISPLAY EN D C AP
OR
116,0
4.57
C LE AR AN C E FOR
EN D C A P REMOVAL
lc FIELD TERMINAL
C O N N E C T IO N S
WITH SO LID EN D C AP
ON E LEC T R O N IC S END
180.5
7 .1 1
- 124,6 -
4.91
LPG REMOTE SEAL
WITH VERTICAL PIPE MOUNT
Figure 8 — Approxim ate vertical mounting dimensions for Remote Seal Transmitter
STR700 Smart Pressure Transmitter
11
Reference Dimensions (cont’d)
Flush Flanged Seal Dimensions
Type
Wetted Materials
AN SI; DIN
Flange
Material
Rating
<— У
Diaphragm
SS
CS
SS
D
Has:elloy С
SS
С
Hasielloy С
Habtelloy С
Mon el
D
Tantalum
SS
С
S3
N/A
В
Hasielloy С
A
Hasielloy С
SS
Ha&telloy С
Manei
Mori el
D
D
Tantalum
SS
SS
С
SS
Mane:
Э" CI-лЬЕ150*
SS
CS
Э" ClaBE
3D0£
ss
Flush
Flanged
•Seal
CS
Э" Class
600 *
ss
CS
-
Hasielloy С
SS
hasielloy С
Habtelloy С
D
D
С
Mane
Monel
Tantalum
SS
SS
N/A
ss
т
A
В
7.5
1.Э7
Instr.oon n
Flange
(N on-w etted)
D
D
С
0.94
7.50
1.37
SS
Hasielloy С
D
Me nei
Ha&telloy С
Monel
Tantalum
SS
С
SS
SS
D
SS
С
Hasielloy С
Habtelloy С
D
Mnnei
Mon el
D
Tantalum
SS
С
SS
Hasielloy С
N/A
SS
В
A
Hasielloy С
И one1
Ha&telloy С
Mon el
D
Tantalum
SS
D
С
S3
SS
D
Hasielloy С
Hasielloy С
SB
Hastelloy С
D
Monei
Mon si
D
SS
SB
N/A
С
Hasielloy С
SB
A
Hasielloy С
HaE-telloy С
D
Mane'
Monsl
D
Tantalum
SS
С
D iaphragm extends
the entire Raised face
gasket surface (wetted)
(diaphragm ) --------
1 5Б
Figure A
1.12
8.25
1.5Б
D
Hasielloy С
(effective
diaphragm )
"A "0
Configuration "HS"
& 35
В
A
Hasielloy С
Tantalum
'
See figure
Body
3.25
1.75
15
3.25
1.75
С
7.B7
В
1.32
Configuration "HT"
Figure В
0.34
7 67
1.Э2
Instr.Conn
Flange (Non-W etted)
Flange Ring
(N on-W etted)
Body
(non-wetted)
Diaphragm extends over
the entire Raised face
gasket surface (wetted)
Raised face Gasket
surface (wetted)
(wetted)
Configuration "IS"
Configuration "IT"
Figure D
Figure С
Figure 9 - Seal Dimensions (Flush Flanged)
12
STR700 Smart Pressure Transmitter
Reference Dimensions (cont’d)
Flush Flanged Seal with Lower
Type
A N S I/D IN
R ating
Class 150#
2.22
2_22
4.25
4.0 0
1.72
1.72
1.72
5.00
2.5 0
3.00
3.40
e.oo
2.5 0
3.00
3.40
7.5 0
2 . as
2 -ae
340
4.0 0
1.72
1-72
5.25
1.84
1.94
2.34
5 .25
1.84
1-84
2 .34
5.25
1.78
r
1.12
1.02
B2
1.99
5.00
2.50
3.00
3.50
1- 1/ 2 "
1- 1/ 2 "
Class 3 0 0 #
T
3"
1"
1- 1/ 2 "
Class 6 0 0 #
2"
31
B2
4.0 0
1.72
1.72
BG
Flush
BD
B1
Dia. (in.)
3.50
1.72
1.72
Ш*
1"
L ow er
4.1" DiapSi.
Dia. (in.)
A
BU
B1
B2
3"
Seal w ith
2.9" D iap li.
Dia. (in.)
D im ension
‘У 1
Flanged
2.4" D iaph.
Size
BO
El
B2
A
BO
51
B2
A
BO
B1
B2
A
BO
B1
B2
A
BO
B1
B2
A
BO
B1
B2
A
BO
B1
B2
A
BO
81
B2
A
BO
B1
B2
A
BO
B1
B2
A
BO
B1
B2
6.00
2.50
3.00
3.50
7.50
2.58
2 .S8
3.50
4 .88
2.50
3.00
3.50
9.12
2.50
3.00
3.50
8.50
2.50
3.00
3.50
8.25
3.48
3.48
4 .10
4.S8
2.50
3.00
3.50
9.12
2.50
3.00
3.50
9.50
3.10
3.60
4.10
8.25
3.48
3.48
4.10
2-22
6.12
2.5 0
3.00
3.40
•5.50
2.5 0
3.00
3.40
QJ25
3.48
3.48
4. DO
4.5 0
2.1 5
2-15
2-40
e .12
1.53
2-OS
2-4S
0.50
3.10
3.30
4.0 0
8.25
3.48
3.48
4-00
2-12
2.12
6.00
2.12
2.12
2.12
7.50
2.00
3 .00
3.40
5.25
1.88
2-12
2-12
5.25
2.12
2-12
2.12
6 .50
2 .70
3 .00
3.50
8 .25
3.20
3.00
4.00
5.25
2 .26
2 .28
2 .50
5.25
2.50
3.00
3.50
6.50
3.30
3.00
4.10
8.25
3 .20
3.00
4.00
Without Flush
В Dimenson with 1/4 NPT Flushing Connection
В g merrsion wth 1/2 NPT Rush
Connect on
Unoer
(Non
0,90
Flush Conn.
(Optional]
~ ~ \|= L
Gasket
Low er
(iletted1
Diaphregm
(Wetted)
Wetted)
Studs not
supplied
Flush Flanged Seal with Lower
Flush Flanged Seal with Lower
Note: 0.90 dim ension is 0.70 for 4 .1 ” Dia Diaphragm
Figure 10- Seal Dimension (Flush Flanged)
STR700 Smart Pressure Transmitter
13
Reference Dimensions (cont’d)
Flanged Seal with Extended Diaphragm
flN:ilJIHN
Type
Dim ension
Rating
Э" Class
iZ O *
Flanged
Ье-al with
PN4G
ExtEnded
Diaphragm
3.5"
Diaphragm
Die. (in.f
Did. (in.)
7.50
0.Э4
2.ВЭ
-
335
-
A
В
С
A
3
С
A
В
С
A
В
С
А
3
С
А
В
3" CI^BB
DIN D4SC-
2.3"
Diaphragm
4" Class
ISO?*
4" Class
з :о ^
DiN DNeCPN4G
С
1.12
2.00
7. В"
0.Э4
2. ВО
-
B.OD
□ .94
a. 70
ю .г а
1.25
-
3.7u
-
S.25
□ .94
a.70
“
"
_
[Design Ed to rreet W:th е-с^ есш е 40 p p5
Figure 11 — Seal Dimensions (Extended Diaphragms)
Pancake Seal
Type
ANSUDIN
Dimension:
Э.5" Diaph.
(in.)
Рэлслке
Seal
S se* D5D#.
eco *
□ NSD-F J4C
A
5 3D
3
1.ПЗ
In s tru m e n t
Connection
Figure 12 — Seal Dimensions (Pancake)
Chemical Tee “Taylor Wedge” Seal
Type
Chemical
Tee ''Taylor
Wedge"
Seal
Бае
Dimension
3.5” Diaph.
(■in.)
A
5. D-D
3
0.ЕЭ
750 psi
(W e tte d )
(W e tte d )
Figure 13 — Seal Dimensions (Chemical TEE “Taylor Wedge” Seals
14
STR700 Smart Pressure Transmitter
Seal with Threaded Process Connection
Type
Threaded
_
Conn. Seal
Size
Dimension
2.4"
2.9™
C l"
Diaphragm
Dia. |ln.|
Diaphragm
Di:i. (in.)
Diaphragm
Dia. (in.)
3.50
i.e e
1.95
2.15
3.50
1 66
1.06
8.25
4.00
1.00
1.00
2 10
4.00
1.00
1.06
2.10
5.25
1.73
1.73
2.14
5.25
1.73
1.73
2.14
A
Б0
Ш " □ г 1/2"
Бг
Б2
A
Б0
3/4" or 1"
B1
Б2
BD
Without Flush
31
Б Di rne-isi or with 1/4 N^T Flush ng Connect un
B2
Б om ens zn wi?h 112 NPT Flushing Comesticn
Figure 14— Seal Dimensions (Threaded Process Connection Seals)
Sanitary Seal
Type
Sanitery
Seal
Size
2 - 112"
Dimension
1.9,r
Diaphragm
2 .4 ”
2 .9 "
Diaphragm
Diaphragm
4.1"
Diaphragm
Dia. (in.|
Dia. (in.|
□ ia. (in.|
Dia. (in.)
A
2.50
-
В
1.42
-
A
3
a.on
-
1.23
A
4"
-
-
3.57
В
A
-
-
1.36
-
-
-
-
4.ea
3
-
-
-
•.0 0
Figure 15— Seal Dimensions (Sanitary Seals)
-
STR700 Smart Pressure Transmitter
15
Saddle Seal
Type
5 jh
Dimension
3"
A
Saddle
Seal
4" or larger
Cenn.
2 A " Diaph.
Nn.)
Bolt
Upper Body
i Mo n - w e t t edi
3.50
3
2. SO
A
3.50
5
З.П4
Weld
by User
Moue: Specify 5 or 5 bolt p a tte r-.
Caskei
( We t t e d I
Lo w e r Housing
(Wetted)
Diaphragm
(Wetted)
Figure 16— Seal Dimensions (3” Saddle Seal)
Type
Size
Dimension
4"
Saddle
Seal
4" or larger
2.4” Diaph.
(in.)
A
3.50
3
2.50
A
3.50
Б
З.П4
Conn.
Upper Body
(H on- wetted)
Noue: Specify 6 or 5 bolt p a tte r-.
Weld _
by User
Gasket
( We t t e d )
Figure 17— Seal Dimensions (4” Saddle Seal)
Calibration Ring
Type
S ize
R a tin g
D im e n s io n
1 5Csf I B 0D 3
A
В
5.0D
1 .on
5. CO
1 .5 0
С
3.0D
3,'DO
C a lib r a tio n
R in g
3"
Ш
PiPT
М2 N P T
Figure 18— Calibration Ring
Bolt
16
STR700 Smart Pressure Transmitter
Communications Protocols & Diagnostics
HART Protocol
Software Download
Version:
Utilizes Class-3 of the Common Software Download
HART 7
procedure as per FF-883 which allows the field devices of
Power Supply
any manufacturer to receive software upgrades from any
Voltage: 10.8 to 42.4Vdc at terminals
host.
Load: Maximum 1440 ohms. See Figure 2.
Honeywell Digitally Enhanced (DE)
Minimum Load: 0 ohms. (For handheld communications a
DE is a Honeywell proprietary protocol which provides
minimum load of 250 ohms is required)
digital communications between Honeywell DE enabled
Foundation Fieldbus (FF)
field devices and Hosts.
Power Supply Requirements
Power Supply
Voltage: 9.0 to 32.0Vdc at terminals
Voltage: 10.8 to 42.4Vdc at terminals
Steady State Current: 17.6mAdc
Load: Maximum 1440 ohms See Figure 2.
Software Download Current: 27.4mAdc
Standard Diagnostics
Available Function Blocks
ST 700 top level diagnostics are reported as either critical
Block Type
Qty
Execution Time
1
n/a
or non-critical and readable via the DD/DTM tools or
Critical Diagnostics___________________________________
Resource
Transducer
1
n/a
Diagnostic
1
n/a
Analog Input
1*
30 ms
PID w /Autotune
1
Integrator
Signal Char (SC)
HART DDDTM tools
Basic Display
Electronic Module DAC Failure
Electronics Module fault
Meter Body NVM Corrupt
Meterbody fault
Config Data Corrupt
Electronics Module fault
Electronic Module Diag Failure
Electronics Module fault
Meter Body Critical Failure
Meterbody fault
45 ms
S ensor C om m T im eout
Meterbody Com m fault
1
30 ms
N on-C iitkiil Diagnostics
1
30 ms
HART DD DTM tools
Display Failure
LCD Display
1
n/a
Flow Block
1
30 ms
Input Selector
1
30 ms
Arithmetic
1
30 ms
Electronic Module Com m
Failure
Meter Body Excess Correct
* Al block may have two (2) additional instantiations.
All available function blocks adhere to FOUNDATION
S ensor O verTem perature
Fixed Current Mode
PV Out of Range
No Factory Calibration
Fieldbus standards. PID blocks support ideal & robust PID
No DAC C om pensation
algorithms with full implementation of Auto-tuning.
LRV Set Error - Zero Config
Link Active Scheduler
Button
Transmitters can perform as a backup Link Active
URV Set E r r o r - Span Config
Button
Scheduler and take over when the host is disconnected.
AO Out o f Range
Acting as a LAS, the device ensures scheduled data
Loop Current Noise
transfers typically used for the regular, cyclic transfer of
control loop data between devices on the Fieldbus.
Number of Devices/Segment
Entity IS model: 6 devices/segment
Meter Body Unreliable C om m
T am per Alarm
No DAC Calibration
S ensor Supply Voltage Low
Refer to ST 700 manuals for additional level diagnostic
Schedule Entries
information
18 maximum schedule entries
Other Certification Options
Number of VCR’s: 24 max
Materials
Compliance Testing: Tested according to ITK 6.0.1
о
NACE M R0175, M R0103, IS015156
STR700 Smart Pressure Transmitter
17
Approval Certifications:
AGENCY
FIELD
PARAMETERS
AMBIENT TEMP
(Та)
All
Note 1
-50 =C to 85=C
4-20 m A /D E /
HART
Note 2a
-50 =C to 70=C
Foundation
Fieldbus
Note 2b
4-20 mA / DE/
HART/ Foundation
Fieldbus
Note 1
-50 =C to 85=C
Enclosure: Type 4Х /1 Р 6 6/IP67
All
All
-
Explosion Proof:
Class 1, Division 1, Groups А, В, C, D;
Dust Ignition Proof:
Class II, III, Division 1, Groups E, F, G; T4
All
Note 1
-50 =C to 85=C
4-20 m A /D E /
HART
Note 2a
-50 =C to 70=C
Foundation
Fieldbus
Note 2b
4-20 mA / DE/
HART/ Foundation
Fieldbus
Note 1
TYPE OF PROTECTION
Explosionproof:
Class I, Division 1, Groups А, В, C, D;
Dust Ignition Proof:
Class II, III, Division 1, Groups E, F, G; T4
COMM.
OPTION
Class 1, Zone 0/1, AEx d IIC Ga/Gb T4
Class II, Zone 21, AEx tb NIC Db T 95°C
Intrinsically Safe:
Class 1, II, III, Division 1, Groups А, В, C,
D, E, F, G:T4
FM Approvals™
Class 1, Zone 0, AEx ia IIC Ga T4
-50 =C to 70=C
FISCO Field Device (Only fo r FF Option)
Exia IICT4
Nonincendive:
Class 1, Division 2, Groups А, В, C, D
locations,
Class 1, Zone 2, AEx nA IIC Gc T4
Ex d IIC Ga T4
Ex tb INC Db T 95°C
Canadian
Standards
Association
(CSA)
Intrinsically Safe:
Class 1, II, III, Division 1, Groups А, В, C,
D, E, F, G; T4
Exia IIC Ga T4
FISCO Field Device (Only fo r FF Option)
Exia IICT4
Nonincendive:
Class 1, Division 2, Groups А, В, C, D; T4
-50 aC to 70aC
-50 =C to 85=C
Ex nA IIC Gc T4
Enclosure: Type 4Х /1 Р 6 6/IP67
All
All
-
18
STR700 Smart Pressure Transmitter
Approval Certifications: (Continued)
Flameproof:
II 1/2 G Ex d IIC Ga/Gb T4
II 2 D Ex tb NIC Db T 95°C
Note 1
-50 =C to 85=C
4-20 m A /D E /
HART
Note 2a
-50 =C to 70=C
Foundation
Fieldbus
Note 2b
4-20 mA / DE/
HART/
Foundation
Fieldbus
Note 1
-50 =C to 85=C
Enclosure: IP66/IP67
All
All
-
Flameproof:
Ex d IIC Ga/Gb T4
Ex tb NIC Db T 95°C
All
Note 1
-50 =C to 85=C
4-20 m A /D E /
HART
Note 2a
-50 =C to 70=C
Foundation
Fieldbus
Note 2b
4-20 mA / DE/
HART/
Foundation
Fieldbus
Note 1
-50 =C to 85=C
Enclosure: IP66/IP67
All
All
-
Flameproof:
Ex d IIC Ga/Gb T4
Ex tb NIC Db T 95°C
All
Note 1
-50 =C to 85=C
4-20 m A /D E /
HART
Note 2a
-50 =C to 70=C
Foundation
Fieldbus
Note 2b
4-20 mA / DE/
HART/
Foundation
Fieldbus
Note 1
-50 =C to 85=C
Enclosure: IP66/IP67
All
All
-
Flameproof:
Ex d IIC G a/G bT4
Ex tb NIC Db T 95°C
All
Note 1
4-20 m A /D E /
HART
Note 2a
Foundation
Fieldbus
Note 2b
4-20 mA / DE/
HART/
Foundation
Fieldbus
Note 1
-50 =C to 85=C
All
All
-
Intrinsically Safe:
II 1G Exia IIC Ga T4
ATEX
FISCO Field Device (Only fo r FF Option)
Exia IICT4
Nonincendive:
II 3G Ex nA IIC Gc T4
Intrinsically Safe:
Exia IIC Ga T4
lECEx
(World)
FISCO Field Device (Only fo r FF Option)
Exia IICT4
Nonincendive:
Ex nA IIC Gc T4
Intrinsically Safe:
Exia IIC Ga T4
SAEx
(South Africa)
FISCO Field Device (Only fo r FF Option)
Exia IICT4
Nonincendive:
Ex nA IIC Gc T4
INMETRO
(Brazil)
Intrinsically Safe:
Exia IIC Ga T4
FISCO Field Device (Only fo r FF Option)
Exia IICT4
Nonincendive:
Ex nA IIC Gc T4
Enclosure : IP 66/67
All
-50 aC to 70aC
-50 aC to 70aC
-50 aC to 70aC
T5 Та = - 5 0 to 93aC
T4 Та = - 5 0 to 93aC
T4 Та = - 5 0 to 70aC
STR700 Smart Pressure Transmitter
19
Approval Certifications: (Continued)
Flameproof:
Ex d IIC Ga/Gb T4
Ex tb NIC Db T 85°C
Intrinsically Safe:
Exia IIC Ga T4
NEPSI
(China)
All
Note 1
4-20 m A /D E /
HART
Note 2a
Foundation
Fieldbus
Note 2b
FISCO Field Device (Only fo r FF Option)
Exia IICT4
mA / DE/
HART/
-50 =C to 70=C
-50 aC to 70aC
4-20
Nonincendive:
Ex nA IIC Gc T4
Foundation
Fieldbus
Note 1
-50 =C to 85=C
Enclosure : IP 66/67
All
All
-
Flameproof:
1 Ex d IIC Ga/Gb T4
Ex tb NIC Db T 85°C
All
Note 1
-50 =C to 85=C
4-20 m A /D E /
HART
Note 2a
-50 =C to 70=C
Foundation
Fieldbus
Note 2b
All
All
Intrinsically Safe:
OExia IIC Ga T4
GOST
T5 Та = - 5 0 to 93aC
FISCO Field Device (Only fo r FF Option)
Exia IICT4
Enclosure : IP 66/67
-50 aC to 70aC
Notes:
1. Operating Parameters:
Voltage= 11 to 42 V DC
2.
Current= 4-20 mA Normal
= 10 to 30 V (FF)
Intrinsically Safe Entity Parameters
a.
Analog/DE/HART Entity Values:
Vmax= Ui = 30V
= 30 mA (FF)
lmax= li= 105mA
Ci=4.2nF
Li =984 uH
Pi =0.9W
Li = 0
Pi =0.9W
Transmitter w ith Terminal Block Revision E or L ate r)
Vmax= Ui = 30V
lmax= li= 225mA
Ci=4.2nF
Note : Transmitter w ith Terminal Block Revision E or later
The revision is on th e label th a t is on th e m odule. There w ill be tw o lines o f te x t on th e label:
•
First is th e M o d u le Part #: 50049839-001 o r 50049839-002
•
Second line has th e su p p lie r in fo rm a tio n , along w ith th e REVISION:
XXXXXXX-EXXXX, THE "X" is p ro d u ctio n related, THE POSITION o f th e "E" IS THE REVISION.
b.
Foundation Fieldbus- Entity Values
Vmax= Ui = 30V
lmax= li= 180mA
C i=0nF
Li = 984uH
Pi =1W
Transmitter w ith Terminal Block Revision F or L ate r)
Vmax= Ui = 30V
lmax= li= 225mA
Ci =0nF
Li = 0
Pi =1 W
FISCO Field Device
lmax= li= 380 mA
C i=0nF
Li = 0
Pi =5.32 W
Vmax= Ui = 17.5V
Note : Transmitter w ith Terminal Block Revision F or later
The revision is on th e label th a t is on th e m odule. There w ill be tw o lines o f te x t on th e label:
•
First is th e M o d u le Part #: 50049839-003 o r 50049839-004
•
Second line has th e su p p lie r in fo rm a tio n , along w ith th e REVISION:
ХХХХХХХ-ЕХХХХ, THE "X" is p ro d u ctio n related, THE POSITION o f th e "E" IS THE REVISION.
20
STR700 Smart Pressure Transmitter
Approval Certifications: (Continued)
This certificate defines the certifications covered for the ST 800 Pressure Transmitter family of
products, including the SMV 800 Smart Multivariable Transmitter. It represents the compilation of
the five certificates Honeywell currently has covering the certification of these products into marine
applications.
For ST 800 Smart Pressure Transmitter and SMV800 Smart Multivarible Transmitter
American Bureau of Shipping (ABS) - 2009 Steel Vessel Rules 1-1-4/3.7, 4-6-2/5.15, 4-8-3/13 &
13.5, 4-8-4/27.5.1, 4-9-7/13. Certificate number: 04-HS417416-PDA
Marine Certificates
Bureau Veritas (BV) - Product Code: 389:1 H. Certificate number: 12660/B0 BV
Det Norske Veritas (DNV) - Location Classes: Temperature D, Humidity B, Vibration A, EMC B,
Enclosure C. For salt spray exposure; enclosure of 316 SST or 2-part epoxy protection with 316
SST bolts to be applied. Certificate number: A-11476
Korean Register of Shipping (KR) - Certificate number: LOX17743-AE001
Lloyd's Register (LR) - Certificate number: 02/60001 (E1) & (E2)
SIL 2/3 Certification
IEC 61508 SIL 2 for non-redundant use and SIL 3 for redundant use according to EXIDA and TLIV
Nord Sys Tec GmbH & Co. KG under the following standards: IEC61508-1: 2010; IEC 61508-2:
2010; IEC61508-3: 2010.
STR700 Smart Pressure Transmitter
Application Data
Liquid Level: Closed Tank
Determine the minimum and maximum pressure
differentials to be measured (Figure 16).
PMin = (SGp x a) - (SGf x d)
= LRV when HP at bottom of tank
= -U R V when LP at bottom of tank
PMax = (SGp x b) - (SGf x d)
= URV when HP at bottom of tank
= -LR V when LP at bottom of tank
Where:
minimum level at 4mA
maximum level at 20 mA
a = distance between bottom tap and
minimum level
b = distance between bottom tap and
maximum level
d = distance between taps
SGf = Specific Gravity of capillary
fill fluid (See Page 6 “Material
Specifications” for values.)
SGp = Specific Gravity of process fluid
21
22
STR700 Smart Pressure Transmitter
Application Data (Cont’d)
Density or Interface*
Calculate the minimum and maximum pressure
differentials to be measured (Figure 19).
Pmin = (SGmjn - SGf) x (d);
minimum density, 4mA output
Pmax = (SGmax - SGf) x (d);
maximum density, 20mA output
Where:
d = distance between the taps
SGmax = maximum Specific Gravity
SGmjn = minimum Specific Gravity
SGf = Specific Gravity of capillary fill fluid (See
Page 6 “Material Specifications” for values.)
Figure 19- Density, direct acting transmitter
configuration
Seal Configurations
Figure 20— Flush Flange Seals
Flush Flange Seals can be used with differential, gauge
and absolute pressure transmitters and are available with
3” ANSI Class 150, ANSI Class 300 and DIN DN80-PN40
process connections. Flush flange seals can also be
Figure 22— Pancake Seals
Pancake Seals can be used with differential, gauge and
absolute pressure transmitters and are available with 3”
ANSI Class 150, 300 and 600 process connections.
provided with Lowers. Lowers are essentially calibration
rings, which allow flushing connections if needed.
Figure 21 — Flange Seal with Extended Diaphragm
Figure 23— Chemical Tee “Taylor” Wedge
Flange Seal with Extended Diaphragm can be used with
Chemical Tee “Taylor” Wedge can be used with
differential, gauge and absolute pressure transmitters and
differential pressure transmitters and are available with
are available with 3’’ and 4” ANSI Class 150, ANSI Class
Taylor Wedge 5” O.D. process connection.
300, DIN DN80-PN40 and DIN DN100-PN40 process
connections. 2”, 4” and 6” extension lengths are available
STR700 Smart Pressure Transmitter
23
Seal Configurations (cont’d)
Figure 24— Seals with Threaded Process
Connections
Figure 28 — Stainless Steel Armor and PVC Coated
Stainless Steel Armor Capillaries
Seals with Threaded Process Connections can be used
Stainless Steel Armor and PVC Coated Stainless Steel
with differential, gauge and absolute pressure
transmitters and are available with V2 , 3A” and 1” NPT
Armor Capillaries are available with Honeywell Remote
Seal Solutions.
Female process connections.
Figure 25 — Sanitary Seals
Sanitary Seals can be used with differential, gauge and
Figure 29 — 2” Stainless Steel Nipples
2” Stainless Steel Nipples are available for CloseCoupled remote seal solutions
absolute pressure transmitters and are available with 3”
and 4” Tri-Clover-Tri-Clamp process connections.
Ф
Figure 26— Saddle Seals
absolute pressure transmitters and are available with 3”
Figure 30 — Welded Meter Body for All-Welded
Remote Seal Solution
Welded Meter Body for All-Welded Remote Seal Solution.
and 4” (6 bolt or 8 bolt designs) process connections.
The welded ST 800 meter body is an important part of an
Saddle Seals can be used with differential, gauge and
All-Welded Remote Seal Solution, which is commonly
used in Vacuum applications.
Figure 27 — Calibration Rings
Calibration Rings are available with Flush Flange Seals
and Pancake Seals. Flushing ports (1/4” or V2”) are
available with calibration rings.
Model Selection Guide
Model Selection Guides are subject to change and are inserted into the specifications as guidance only.
Prior to specifying or ordering a model check for the latest revision Model Selection Guides which are published at:
Model STR700
(DP, GP) Remote Seals
M o d e l S e le c tio n G u id e
34-S T -16 -10 4 Issue 4
In s tru c tio n s
Select the desired Key Number. The arrow to the right marks the selection available.
Make selections from each Table (I, II and IX) using the column below the proper arrow.
A (•) denotes unrestricted availability. A letter denotes restricted availability.
Restrictions follow Table IX.
IV
i
Key N um be r
II
П
II
П
V
0000
П
KEY N U M B ER
URL
LRL
Max Span
Min Span
Units
Selection
M easurem ent
Range Std Accuracy
100 (7)
-100 (-7)
100 (7)
1 (0.07)
psi (bar)
STR73D
500 (35)
-9 (-0.62)
500 (35)
5 (0.35)
psi (bar)
STR74G
Note:
1
1
Remote seal system pressure rating is body rating or seal rating, w hichever is less.
Description
TABLE 1
b. Prim ary Fill
Fluid
Silicone Oil 200
Fluorinated Oil CTFE
c. Construction
In-Line Gauge
Dual Head DP
d. Bolts and
Nuts
forTransm itter
Heads
e. Secondary
Fill Fluid
(capillary &
seal)
f. C o n n e c tio n
o f R e m o te
S e a l to M e te r
B ody
4 —
g. Seal Option
Selection
1 Remote Seal (High Side)
2 Remote Seals
1 Remote Seal (Low Side)
a. Number of
Seals
Meter Body&
Capillaries
Availability
•
•
•
1
2
3
1
2
•
•
•
2
2
Non-W etted Adapter Head M aterials
316 SS Bonnet
316 SS Bonnet for Close-Couple
316 SS (bolt-on heads)
316 SS for Close-Couple
316 SS with all-welded m eter body
None
__ A ______
В
С
__ D _______
E
____ 0 _____
22
Carbon Steel Bolts and Nuts
____ С _____
•
•
3
•
3
4
•
316 SS Bolts and Nuts
____ S _____
•
A286 SS (NACE) Bolts and 304 SS (NACE) Nuts
____ N _____
•
B7M (NACE) Bolts and 7M (NACE) Nuts
__ В ___
•
No Fill Fluid
Silicone Oil 200
0
______ 1 ___
______ 2 ___
•
•
5
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Fluorinated Oil CTFE
Silicone 0 il7 0 4
1
Neobee® M20
Syltherm®800 12
No Capillary, No Ni pple (Specifyfor VAM Unit Only)
5 feet
1.5 m
10 feet
3.0 m
15 feet
4.5 m
SS Armor
20 feet
6.1 m
25 feet
7.5 m
Capillary
35 feet
10.7 m
Length
5 feet
1.5 m
10 feet
3.0 m
PVC Coated SS
15 feet
4.5 m
20 feet
6.1 m
Armor
25 feet
7.5 m
35 feet
10.7 m
2 inch long SS nipple close-coupled
None
Std Gold Plated Seal Diaph. = 50 |iin
Teflon Coated Seal Diaphragm - onlyfor anti-sticking
__ 3 ___
__ 4 ___
______ 5 ___
0
A
В
С
D
E
F
G
H
J
К
L
M
2
11 Limited vacuum availability.
12 Minimum static pressure requirement. No vacuum allowed. See Specifications 34-ST-03-88 Figure 15
In-Line Gauge
Dual Head DP
All welded
6
6
0
1
•
•
7
7
4
7
7
STR700 Smart Pressure Transmitter
25
STR74G
STR73D
Note: W hen s e le c tin g req u ire d s e a l, you m u s t sp e cify
_______ o n ly the 9 s e le c tio n s w ith in the re q u ire d se a l type.
Selection
Description
TABLE II
No Seal Attached to C ore T ra n s m itte r (S p e cify for VAM U n it Only)
Seal Type
Diaphrag
m
D ia m e t e r
Flange
Size
3”
3.5"
80m m
W etted Material
N on-W etted M aterial
Seals
F lush F langed
Seal
Flange P ressure
Rating 1
AFA
ANSI C la s s 300
AFC
DIN D N 8 0 -P N 4 0
AFM
Diaphragm
Upper Insert
3 1 6 L SS
3 1 6 L SS
Hastelloy® C-276
3 1 6 L SS
AB
Hastelloy® C-276
Hastelloy® C-276
AC
M onel 400®
M onel 400®
AE
T an ta lu m 5
3 1 6 L SS
AF
3 1 6L SS
C e n te r Seal
C o n n e ction
S ide Seal
C o n n e ctio n s
Selection
AA
None
A
3 1 6L SS
_B_
10
Hastelloy® C -2 76
_C .
10
M onel 400®
D
10
None
0
O ne 1/4 w ith p la s tic plug
_H
One 1/4 " w ith m e ta l plug
_J
(Metal plug material
Tw o 1/4" w ith p la s tic p lu g s
.M
w ill be the same as
T w o 1/4' w ith m eta l p lu g s
.N
Cal. ring material if
O ne 1/2’' w ith p la s tic plug
_P
metal plug is chosen )
One 1/2 " w ith m e ta l plug
.Q
Tw o 1/2" w ith p la s tic p lu g s
_R
a n d P lu g s 4
21
CS (N ickel Plated)
(up p e r)
F lu sh in g
21
Selection
ANSI C la s s 150
S e a l-C a p illa ry
C a lib ra tio n R ings
000000000
T w o 1/2' w ith m eta l p lu g s
S
Table II continued next page
1 Standard facing 125-250 AARH RF (raised face) serrated surface finish.
4 Plastic Hugs are TEMPORARY ONLY to protect threads and MUST be REMOVED before installation
5 Tantalum Upper insert has Tantalum w etted parts and 316 SS or CS non-w etted parts
Note: Remote seal system pressure rating is body rating or seal rating, w hichever is less.
26
STR700 Smart Pressure Transmitter
STR73D -
TABLE II
Flange
Size
1"
1-1/2"
2.4"
2"
3"
1/2"
1"
S pec. Figure 34-
Figure 34-S T-03-104
Rating 1
S T-03-104
ANSI 150
22
BCA
12
•
ANSI 300
22
BCC
12
•
ANSI 150
22
BGA
12
•
ANSI 300
22
BGC
12
•
ANSI 150
22
BDA
12
•
ANSI 300
22
BDC
12
•
ANSI 150
22
В FA
12
•
ANSI 300
22
BFC
12
•
ANSI 150
23
CAA
•
•
ANSI 150
23
CCA
•
•
23
CCC
•
•
22
CGA
•
•
ANSI 300
22
CGC
•
•
ANSI 150
22
CDA
•
•
ANSI 300
22
CDC
•
•
1/2"
ANSI 150
22
DAA
•
•
1"
ANSI 150
ANSI 300
23
DCA
•
•
23
DCC
•
•
ANSI 150
23
DGA
•
•
ANSI 300
23
DGC
•
•
ANSI 150
23
DDA
•
•
ANSI 300
22
DDC
•
•
ANSI 150
22
DFA
•
•
DFC
•
•
•
•
•
•
•
•
8
8
8
8
____ B H ______
S e le c tio n
8
13
13
U pper
U p p e r In s e rt
3 1 6 LS S
31 6 LS S
4
•
•
Carbon Steel
3 1 6 LS S
5
•
•
•
•
•
•
I
Tantalum Clad
•
•
I
and Tantalum Clad)
Tantalum
8
•
•
l
(SS Hug fo r CS L o w e r
Hastelloy® C-276
•
•
I
metal plug is chosen -
Monel 400®
31 6 LS S
•
•
i
L o w e r material, if
Hastelloy® C-276
Monel 400®
Tantalum
Tantalum
•
•
i
w ill be the same as
Hastelloy® C-276
_ BA
____ B B ______
____ B C ______
B E _____
____ BF______
____ B G ______
•
•
I
(Metal plug material
31 6 LS S
31 6 LS S
•
•
i
and Plugs4
3 1 6 LS S
Hastelloy® C-276
•
•
К
•
•
G
•
•
T
•
•
L
15
15
No Selection
None
One 1/4" with plastic plug
One 1/4"with metal plug
Two 1/4" with plastic plugs
Two 1/4"with metal plugs
One 1/2" with plastic plug
One 1/2"with metal plug
Two 1/2" with plastic plugs
Two 1/2"with metal plugs
Klinger® C-4401
(non-as bestos)
Grafoil®
Teflon®
Gylon®3510
0
0
I
I
I
I
I
I
I
B o ltsf
Flushing
Connections
S e le c tio n
I
I
I
I
I
I
I
Non-Wetted Material
(upper, upper insert)
22
Low er
I
I
I
I
I
I
I
Wetted Material
ANSI 300
D iaphragm
I
I
I
I
I
I
I
3"
I
I
I
I
I
I
I
2"
I
I
I
I
I
I
I
1-1/2"
Gasket
C o n s tru c tio n - S ee Spec.
ANSI 300
1-1/2"
Flush Flanged
Seal
with Lower
P r e s s u re
ANSI 150
2"
4.1"
C o n s t. - See
I
I
I
I
I
I
I
2.9"
R an g e
I
I
I
I
I
I
I
Seal Type
S e a ls (c o n tin u e d )
S e le c tio n
D e s c rlp to n
D ia p h ra g
m
D ia m e te r
Table II continued next page
1 Standard fa cing 125-250 AAR H RF (raised face) serrated su rfa c e finish.
8 Bolt material w ill be same as Upper Material. H ow ever, if Table I bolts/nuts material is N A C E or B7M, seal bolt material w ill be 304 SS NACE.
4 Hastic Rugs are TEMPORARY ONLY to protect threads and MUST be REMOVED before installation
Note: Remote seal system pressure rating is body rating or seal rating, w h ic h e v e r is less.
STR700 Smart Pressure Transmitter
27
STR73D Descripton
D iaphragm
D ia m e te r
Flange
Size
Flange Pressure Rating 1
2.8"
3"
(2.8" OD
ANSI C lass 150
ANSI C lass 300
exten s io n )
with Extended
Diaphragm
Wetted Material
EFM
•
FGA
FGC
•
•
•
•
DIN D N100-PN40
FGP
•
•
•
•
•
•
•
•
•
•
•
•
Diaphragm
316L SS
Hastelloy® C-276
Ext. Tube
316L SS
316L SS
Hastelloy® C-276 Hastelloy® C-276
Non-W etted
CS (Nic <el Plated)
Material (flange)
31f 5LSS
Bolts
No Selection
2"
4"
6"
Extension Length
No Selection
DIN DN80-PN40
ANSI C lass 150
ANSI C lass 300
•
•
•
No Selection
Selection
EA_
____ E B ____
EC
7
8
•
•
•
•
•
•
•
•
•
•
0
M
Flange Seal
Seals (continued)
•
I
exten s io n
•
:
3.5"
EFA
EFC
I
I
I
I
I
I
I
4"
(3.70" OD
Selection
I
I
I
I
I
I
I
Seal Type
I
I
I
I
I
I
I
O)
i
TABLE II
No Selection
0
Table II continued below
STR74G
STR73D
TABLE II
Descriptor!
D ia p h r a g
Seal Type
m
D ia m e te r
Flange
Size
3.5"
3"
Wetted Material
Seals (continued)
Flange Pressure Rating
Dependent on Customer Flange
ANSI C lass 150/300/600
Diaphragm
Body
316L SS
Hastelloy® C-276
316L SS
316L SS
Hastelloy® C-276 Hastelloy® C-276
Selection
GFA
GA
GB
GC
Monel 400s
Monel 400®
GE
Tantalum
Tantalum 7
GG
0
Non-W etted Material
No Selection
Bolts
No Selection
C alibration Rings
None
A
316LSS
,B _
Hastelloy® C-276
,C _
Monel 400®
D
Pancake Seal
Flushing
Connections
None
0
0
One 1/4" with p lastic plug
_H
One 1/4" with m etal plug
_J
(Metal plug material
Two 1/4" with p la stic plugs
.M
w ill be the same as
Two 1/4" with m etal plugs
.N
Cal. Ring material, if
One 1/2" with p lastic plug
_P
metal plug is chosen )
One 1/2" with m etal plug
.Q
Two 1/2" with p la stic plugs
_R
and P lu g s4
Two 1/2" with m etal plugs
1 Standard facing 125-250 AARH RF (raised face) serrated surface finish.
4 Hastic Hugs are TEMPORARY ONLY to protect threads and MUST be REMOVED before installation
7 Tantalum Body has Tantalum wetted parts and 316 SS non-wetted parts
Note: Remote seal system pressure rating is body rating or seal rating, w hichever is less.
10
10
10
S
Table II continued next page
28
STR700 Smart Pressure Transmitter
STR74G
STR73D TABLE II
D escripton
Seal Type
Diaphrag
m
Diameter
Flange
Size
3.5"
W e d ge
Flange P ressure Rating 1
Selection
Taylor
750 psi
HM0
16
5" O.D.
W
Se a ls (continued)
*
W etted M aterial
C h e m ic a l Tee
"Taylor" W e d g e
Diaphragm
Body
S election
316LSS
316LSS
____ H A _______
•
Hastelloy'' C-276
316LSS
____ H B _______
•
Hastelloy'' C-276
Hastelloy'' C-276
_ __HC__
•
N o n -W e tte d M aterial
N o S e le c tio n
B olts
N o S e le c tio n
Styles
N o S e le c tio n
N o S e le ctio n
N o S e le c tio n
0
•
_____0 __
•
•
0
0
•
Table II continued below
STR74G
Descripton
TABLE II
Seal Type
Diaphrag
m
Diameter
STR73D —
P ressure Rating
Th readed Process
Connection Size
(NPT Fem ale)
CS Bolts
1/2 N P T
2.4"
3/4 N P T
304 SS
Bolts
2 ,5 0 0
1,250
psi
psi
1 NPT
3/4 N P T
2 ,5 0 0
1,250
psi
psi
1 NPT
3/4 N P T
1,500
7 50
psi
psi
1 NPT
W etted M aterial
Seals (continued)
S e a l w ith
T h re a d e d
P ro ce ss
C o n n e c tio n
KJG
KKG
KLG
1/2 N P T
4.1"
JK G
JL G
1/2 N P T
2.9"
Selection
JJG
LJG
LKG
LLG
Selection
Diaphragm
Low er
316LSS
C a rb o n S teel
JA
316LSS
316LSS
JB_
H astelloy'' C-276
316LSS
JC _
H a stelloy1' C-276
Hastelloy1' C-276
JD
M onel 4 0 0 (
T a n ta lum
M o n e l400®
316LSS
JE
T a n ta lum
Hastelloy1' C-276
JG
JF
N o n -W e tte d M aterial
C S (N icke l P lated)
A
(u pp e r)
3 1 6 S ta in le s s S te e l
С
C a rb o n S teel
.С .
3 0 4 SS
О
metal plug is chose n -
O ne 1/2" w ith m e ta l p lu g
(S S Hug fo r CS Low er
Tw o 1/2" w ith p la s tic p lu g s
0
H
J
M
N
p
Q
R
Tw o 1/2" w ith m e ta l p lu g s
S
F lu sh in g
C o n n e c tio n s
a n d P lu g s 4
N one
O ne 1/4" w ith p la s tic p lu g
O ne 1/4" w ith m e ta l p lu g
(Metal plug material
Tw o 1/4" w ith p la s tic p lu g s
w III be the same as
Tw o 1/4" w ith m e ta l p lu g s
L o w e r material, if
O ne 1/2" w ith p la s tic p lu g
and Tantalum Clad)
G a ske t
17
17
•
•
•
•
•
18
18
18
•
•
•
•
•
18
18
18
18
18
K lin g e r C -4401
(n o n -a s b e s to s )
К
•
•
Grafoil®
G
T
•
•
•
•
L
15
15
Teflon®
G ylon® 3510
Table II continued next page
1 Standard fa cin g 125-250 A A R H RF (raised fa c e ) serra te d s u rfa c e finish.
4 Plastic Rugs are TEMPORARY ONLY to protect thre ads and MUST be REMOVED before installation
“ If Table I Bolts and Nuts material option is NACE, Bolts and Nuts w ill ship w ith A lloy Steel N A C E and M A W P m ay change.
Note: Remote seal sy s te m p ressure rating is body rating or seal rating, w h ic h e v e r is less.
STR700 Smart Pressure Transmitter
29
STR74G
STR73D —
TABLE
II
Descripton
Seal Type
D ia p h ra g
m
D iam eter
Flange
Size
P re s s u re Rating
Selection
19
1.9"
2”
2.4"
2-1/2"
C u s to m e r c la m p rating or
NE0
20
19
2.9"
3”
600 psi, w h ich e ve r is le ss
PF0
19
19
4.1"
4"
QG0
19
19
•
•
•
•
•
•
Seals (continued)
W etted M aterial
S anitary Seal
MD0
Diaphragm
Body
Selection
316L SS
316LS S
____ N A _______
N on-W etted M aterial
No S election
Bolts
No S election
Styles
T ri-C lover Tri-C lam p®
G a ske t
No S election
0
0
8
0
•
•
•
•
Table II continued below
STR74G
TABLE I
STR73D -
Descripton
D ia p h ra g
Seal Type
m
D ia m e te r
2.4"
8-Bolt
Size and
Bolt
Pattern
Seal Pressure Rating
C.S. Bolts
304 SS Bolts
for 3" Pipe
a 4" pipe
2 ,500 psi
1,250 psi
for 3" Pipe
a 4" pipe
2 ,000 psi
1,000 psi
Diaphragm
Lower Housing
D e sig n
2.4"
6-Bolt
D e sig n
3 16L SS
W etted M aterial
Seals (continued)
S addle Seal
C a rbon Steel
12
RGK
12
RPK
12
RQK
12
Selection
RA_
316LS S
RB
Hastelloy® C-276
316LS S
. RC_
Hastelloy® C-276
Hastelloy® C-276
RD
3 16L SS
N/A-Body Only 10
_SB_
SC
Selection
Body
Bolts 1011
C arbon Steel
C arbon Steel
_B_
3 16L SS
316 SS
С
Bolts
No S election
Styles
No S election
Klinger® C-4401
(n o n -a s b e s to s )
G a ske t
RFK
3 16L SS
Hastelloy® C-276 N/A-Body Only 10
Non-W etted M aterial
Selection
0
0
к
Grafoil®
_G
Teflon®
_T
G ylon®3510
9 All sanitary seals have dairy grade ЗА approval.
10 Bolts are not included w ith "body only" selection.
11 If Table I Bolts and Nuts material option is NACE, seal bolt material w ill be 304 SS NACE.
Note: Remote seal system pressure rating is body rating or seal rating, whichever is less.
L
30
STR700 Smart Pressure Transmitter
STR74G ------STR73D TABLE III
Agency Approvals (s e e d ata s h e e t for Approval Code Details)
0
A
В
С
D
E
F
G
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
_ 1_
2
3
_4_
_ 5_
_ 6_
f
f
f
f
f
f
No A pprovals R eq u ire d
FM E xp lo sio n proof, In trin sica lly Safe, N o n -ince n d ive , & D u stp ro o f
C SA E xp lo sio n proof, In trin sica lly Safe, N o n -ince n d ive , & D u stp ro o f
Approvals
ATEX E xp lo sio n proof, In trin sica lly Safe & N o n -ince n d ive
lEC Ex E xp lo sio n proof, In trin sica lly Safe & N o n -ince n d ive
SAEx/CCoE E xp lo sio n proof, In trin sica lly Safe & N o n -ince n d ive
INMETRO E xp lo sio n proof, In trin sica lly Safe & N o n -ince n d ive
NEPSI E xp lo sio n proof, In trin sica lly Safe & N on -ince n d ive
TABLE IV
TRANSMITTER ELECTRONIC SELECTIONS
Material
Connection
Lightning Protection
P o lye ste r P o w d e r C o a te d A lu m in u m
1/2 NPT
N one
a. Electronic
P o lye ste r P o w d e r C o a te d A lu m in u m
M20
N one
Housing
P o lye ste r P o w d e r C o a te d A lu m in u m
1/2 NPT
Yes
M aterial &
P o lye ste r P o w d e r C o a te d A lu m in u m
M20
Yes
Connection
3 16 S ta in le s s Steel (G rade CF8M)
1/2 NPT
N one
Type
3 16 S ta in le s s Steel (G rade CF8M)
M20
N one
3 16 S ta in le s s Steel (G rade CF8M)
1/2 NPT
Yes
3 16 S ta in le s s Steel (G rade CF8M)
M20
Yes
Analog Output
Digital Protocol
b. O utput/
4 -2 0 m A d c
HART Protocol
Protocol
4 -2 0 m A d c
DE Protocol
none
F ou n d a tio n F ieldb u s
Indicator
Ext Zero, Span & Config Buttons
Languages
c. C ustom er
None
None
N one
In terface
None
Yes (Z ero/S pan Only)
N one
S electio ns
B a sic
None
E n g lish
B a sic
Yes
E n g lish
TABLE V
a. Application
Software
b. O utput Limit,
Failsafe &
W rite P rotect
Settings
CONFIGURATION SELECTIONS
D iagnostics
S ta n d a rd D ia g n o stics
Write Protect
Fail Mode
D isa b le d
H ig h > 2 1 .0 m A d c
D isa b le d
E nabled
E nabled
Lo w <
3 .6 m A d c
H ig h > 2 1 .0 m A d c
Lo w <
3 .6 m A d c
High & Low Output Lim its3
H o n e y w e ll S td
(3.8 - 2 0 .8 m A d c
H o n e y w e ll S td
(3.8 - 2 0 .8 m A d c
H o n e y w e ll S td
(3.8 - 2 0 .8 m A d c
H o n e y w e ll S td
(3.8 - 2 0 .8 m A d c
E nabled
N/A
N/A
F ieldb u s
D isa b le d
N/A
N/A
F ieldb u s
c. General
Factory Standard
Configuration
C u sto m C o n fig u ra tio n (U n it Data R e q u ire d from c u s to m e r)
TABLE VI
A c c u ra c y and
Calibration
S
__ С
f
f
g
g
g
•
g
•
•
•
CALIBRATION & ACCURACY SELECTIONS
Accuracy
Calibrated Range
Calibration Qty
NA
N one
N one
S tandard
Factory Std
S in g le C a lib ra tio n
S tandard
C u sto m (U n it Data R e q u ire d )
S in g le C a lib ra tio n
3 N AM U R O u tp u t Lim its 3 .8 - 2 0 .5 m A d c c a n b e c o n fig u re d b y th e c u s to m e r o r s e le c t c u s to m c o n fig u ra tio n T able V c
0
A
В
21 21
• •
• •
STR700 Smart Pressure Transmitter
31
STR74G STR73D -|
TABLE VII
a. Mounting
Bracket
b. Customer
Tag
ACCESSORY SELECTIONS
Bracket Type
Material
None
None
Angle Bracket
Carbon Steel
Angle Bracket
304 SS
Angle Bracket
316 SS
Marine Approved Angle Bracket
304 SS
Flat Bracket
Carbon Steel
Flat Bracket
304 SS
Flat Bracket
316 SS
Customer Tag Type
No customer tag
One Wired Stainless Steel Tag (Up to 4 lines 26 char/line)
Two Wired Stainless Steel Tag (Up to 4 lines 26 char/line)
0
•
•
1_
•
•
2 __
•
3 _____
•
•
•
5 __
•
•
6 ____
•
•
•
•
•
•
•
•
•
•
•
4 ____
7
0
1
2
Unassembled Conduit Plugs & Adapters
c.
Unassembled
Conduit
Plugs &
Adapters
TABLE VIII
No Conduit Plugs or Adapters Required
1/2 NPT Male to 3/4 NPT Female 316 SS Certified Conduit Adapter
1/2 NPT 316 SS Certified Conduit Plug
M20 316 SS Certified Conduit Plug
Minifast® 4 pin (1/2 NPT)
Minifast® 4 Din (M20)
•
•
n
n
m
n
m
n
n
m
n
m
*
•k
•
С
d
•
•
•
•
•
С
d
•
•
•
•
i
•
e
i
•
e
OTHER Certifications & Options : (String in sequence comma delimited (XX, XX, XX....)
None - No other options
NACE MR0175; MR0103; IS015156 (FC33338) Process wetted parts only
NACE MR0175; MR0103; IS015156 (FC33339) wetted and non-wetted parts
Marine (DNV, ABS, BV, KR, LR) (FC33340)
EN10204 Type 3.1 Material Traceability(FC33341)
Certifications &
Certificate of Conformance (F3391)
Warranty
Calibration Test Report & Certificate of Conformance (F3399)
Certificate of Origin (F0195)
FMEDA(SIL 2/3) Certification (FC33337)
Over-Pressure Leak Test Certificate (1.5XMAWP) (F3392)
u e rtu e a n tor u 2or u l 2service per д ы м и у а
TABLE IX
Factory
A0
_ A2
A6
A7
A8
A9
Manufacturing Specials
Factory Identification
00
FG
F7
MT
FX
F3
F1
F5
FE
TP
OX
| 0000
• «I
b
b
32
STR700 Smart Pressure Transmitter
MODEL RESTRICTIONS
Restriction
Letter
Available Only With
Table
|
Not Available With
Selection(s)
b
Table
|
Selection(s)
Select only one option from this group
Vila
1,2 ,3,5,6 ,7 ____
f
IVb
g
IVb
_F_
_ H ,D _
Vb
_ 1,2,6 _
Ic
__ E ______
la
2
d
с
Id
e
lb
i
m
IVb
IVa
n
IVa
____ 0 , N , B _____
2
2
H
B, D, F, H __
А, С, E, G __
У
__ 0 ___
2
le
2__
_____ 4 ___
3
4
If
2
I
2 __ 0 ____
VI
0
5
VIII
6
I
__ B ,D ___
la
FG, F7, FX, OX,TP,MT,F1
2
____ A F ______
____ B F ______
____ B G ______
II
7
____ B H ______
____ G G ______
- JF
^
____ J G ______
VIII
8
9
II
____ AB2____
10
II
11
II
12
13
FG, F7
__ AA2___
If
AG, 2
II
0
0
A
T
II
VIII
FG, F7
____ BF______
__ BG ___
15
II
__B H __
____ J F ___
____ J G ______
16
I
2
II
17
__ J A ___
JJG
II
18
JKG
JLG
la
19
If
If
AG, 2
20
21
I
______ 000
22
Ic
___E _______
FM ApprovalsSMis a service mark of FM Global
Hastelloy® is a registered trademark of Haynes International
Monel 400® is a registered trademark of Special Metals Corporation.
HART® is a registered trademark of HART Communication Foundation.
FOUNDATION™ Fieldbus is a registered trademark of Reldbus Foundation.
Teflon® is a registered trademark of DuPont.
Neobee® is a registered trademark of Stepan Company.
Syttherr# 800 is a Trademark of Dow Corning Corporation
Klinger® С-4401 is a registered trademark of THERMOSEAL, INC
GRAFOIL®is a registered trademarks of GrafTech International Holdings Inc
Gylon® 3510 is registered trademark of Garlock Sealing Technologies
Tri-Clover Tri-Clamp®is a registered trademark of Alfa-Laval
2
2
STR700 Smart Pressure Transmitter
33
По вопросам продаж и поддержки обращайтесь:
Астана +7(7172)727-132, Волгоград (844)278-03-48, Воронеж (473)204-51-73, Екатеринбург (343)384-55-89, Казань (843)206-01-48,
Краснодар (861)203-40-90, Красноярск (391)204-63-61, М осква (495)268-04-70, Н иж ний Н овгород (831)429-08-12, Н овосибирск (383)227-86-73,
Ростов-на-Дону (863)308-18-15, Самара (846)206-03-16, Санкт-Петербург (812)309-46-40, Саратов (845)249-38-78, Уфа (347)229-48-12
Единый адрес: hw n@ nt-rt.ru
www.honeywell.nt-rt.ru