Quick Start Guide

advertisement
1 Package Contents
TransPort WR11
a
N
RA
IT
DIG
RT
O
SP
b
Antenna
Quick Start Guide
11
WR
TransPort WR11
r
we
Po
EVDO Models
l
na
e
rvic
Sig
Se
90001388_C
c Power Supply
If any item is missing or damaged, please contact your supplier. Also, make a record of any damage that may have occurred during
shipping and report it to the supplier.
Depending on model and configuration, the package will also contain additional cables/antennas as appropriate.
2 Connect Antenna and Power Supply
A Connect Antenna: Connect the cellular antenna to the
connector (SMA Female) on the unit.
B Connect Power Supply: Connect the plug end of the 5 volt power
supply to the power connector on the unit, and plug the other end into
a wall outlet.
Insert power supply end fully and
rotate clockwise to engage
and lock.
N
RA
IT
A
I TR
DIG
R11
TW
OR
P
NS
DIG
11
WR
RT
O
SP
r
we
Po
l
na
e
rvic
Sig
Se
nal
e
rvic
Se
er
Pow
Sig
d
Mounting Tips!
The Digi TransPort WR11 should be positioned on a flat, level surface. The unit is designed for indoor use and should be mounted in a location
with adequate ventilation. Also, do not expose the unit to extreme heat or cold, strong magnetic fields, or liquids.
f
3 Configure the Unit
To use your Digi TransPort WR11, you must first activate the device with your carrier(Verizon or Sprint).
This process involves supplying them with the MEID number from your device which is printed
on the label.
A Connect an Ethernet Cable: Connect one end of the cable to the
ethernet port on the unit and the other end an ethernet port on a PC.
Ensure that the DHCP client is enabled on the PC.
NS
RA
IT
DIG
1
R1
TW
R
PO
Note: The ethernet cable required for the connection is customer supplied.
The cable is not included in the package.
S
ce
rvi
Se
er
ow
l P
a
ign
3 Configure the Unit (Continued)
B Connect to the Web Interface: Open a web browser (such as Firefox, Internet Explorer, Chrome) on your PC and navigate to
http://192.168.1.1. If successful, you will be prompted to enter a username and password. The default username is username, and
the default password is password.
After you have logged in, it is strongly recommended that you immediately change the default username and password.
C CDMA Provisioning: Sprint devices start the provisioning process on startup and no intervention is necessary, skip to the next section.
Note that the provisioning process may take several minutes to complete.
For Verizon devices once the device is activated with the carrier, go to Configuration - Interfaces > Mobile > CDMA Provisioning and
click the Start button under Automatic Provisioning as shown in the following image. The process will take one to two minutes
to complete.
D
Click Reboot when Provisioning is complete.
4 Verify Your Connection
To verify that the device is connected to the cellular network, check to see that the service LED is blinking as shown in the table.
You will also see the mobile IP address on the home page.
I
DIG
RT
PO
NS
A
TR
11
WR
ice
rv
Se
nal
Sig
r
we
Po
Note: When the signal strength is less than -101, the Signal-Strength LED is off. Place the device in a location where it gets a better signal.
What’s Next?
To complete configuration of your device, refer to the Users Guide and Application Notes provided on the Digi support site
(www.digi.com/support).
© 2013 Digi International Inc. Digi, Digi International Inc., and the Digi logo are trademarks or registered trademarks of Digi International Inc., in the United States and other countries worldwide.
Download