Cerro LED
IMPORTANT SAFEGUARDS
a) READ AND FOLLOW ALL SAFETY INSTRUCTIONS
b) Do not use outdoors.
c) Do not mount near gas or electric heaters.
d) E
quipment should be mounted in locations and at heights where
it will not readily be subjectd to tampering by unauthorized personnel.
e) T
he use of accessory equipment not recommended by the manufacturer
may cause an unsafe condition.
f) Do not use this equipment for other than intended use.
g) Transfer switch for UL924 applications supplied by others.
h) For UL924 applications maximum installation height is 40ft.
SAVE THESE INSTRUCTIONS
Installation Instructions: Surface Mount (F)
Tools Required (not included): Phillips Screw Driver
Junction Box
Adaptor Plate
Junction Box and (2-4)
Mounting Screws
(supplied by others)
Luminaire
Driver Box
Assembly
Center Support
Ring
Figure A
1. Mount junction box flush with ceiling or wall surface.
2. Install (2-4) mounting screws into junction box (leave loose
approximately 1/8”).
3. Connect feed wires from Luminaire into junction box.
4. Remove center support ring per Figure A.
5. L oosen, but do not remove, (2) screws and drop Driver Box
Assembly.
6. Install fixture flush to wall while inserting junction box mounting
bolts into Adaptor Plate key holes.
7. Twist fixture clockwise to lock bolts into slots and tighten (2-4)
junction box mounting bolts (accessing through the center of the
fixture).
8. Reinstall driver box assembly and tighten (2) mounting bolts.
9. Install options per Figure B.
10. Reinstall center support ring per Figure C.
Figure C
Figure B
Luminaire
Collector Lens
(CL) Option
Spacer Ring
(W) Option
Opal Glass
Diffuser (GD)
Option
CLICK!
Perforated Center
Plate (PC) Option
Solid Center
Plate
Center Ring
Page 1 of 3
(Rev. 09/15)
CERL_INST_v2.0
Cerro LED
Installation Instructions: Rigid Stem (RS) and Swivel Stem (S)
Tools Required (not included): Phillips Screw Driver
Junction Box and (2)Mounting Screws
(supplied by others)
Mounting Nut
Spanner Bar
Canopy
Grounding
Bolt
1/4” Stem
Luminaire
1. Remove center support ring per Figure A.
2. Install options per Figure B.
3. Reinstall center support ring per Figure C.
4. Mount Spanner Bar on Junction box with (2) mounting screws.
5. R
oute feed wires through Stem and screw Stem into Bushing on
Luminaire.
6.Route Stem through Canopy and Spanner Bar and secure with
Mounting Nut.
7. Connect feed wires from Luminaire into Junction Box and connect
Grounding Bolt.
8. M
ove Canopy flush with ceiling or Junction Box and tighten set
screw.
1/4” Stem
Stem Mount Bushing
Figure A
Figure C
Figure B
Luminaire
Collector Lens
(CL) Option
Spacer Ring
(W) Option
Opal Glass
Diffuser (GD)
Option
CLICK!
Perforated Center
Plate (PC) Option
Solid Center
Plate
Center Ring
CAUTION
DANGER
LED Radiation.
Hazardous voltage.
Do not operate while LEDs
are exposed.
Only work on de-engergized
equipment. Disconnect
power before wiring fixture.
Do NOT stare into Beam.
Can cause eye damage.
Contact will cause
electric shock or burn.
Selux Corporation © 2015, T 845-834-1400, 800-735-8927, F 845-834-1401, www.selux.us
Please Note: Disconnect electricity to fixture before working. To be performed by trained personnel only. It is the responsibility of the installer to ensure all electrical, mechanical, and thermal compatibility of the installation site and luminaires prior to installation. Please observe all relevant building codes and regulations.
Keep these instructions after unpacking fixture. For indoor use only. For detailed spec sheets and more information on this and our full range of products, please
visit our website at selux.us. Warranty information: http://www.selux.us/en/resources/terms-and-warranty.html
NOTICE
Do not touch LED
May damage device
Observe precautions for
handling electrostatic
sensitive devices.
Page 2 of 3
(Rev. 09/15)
CERL_INST_v2.0
Cerro LED
Installation Instructions: Cable (C)
Tools Required (not included): Phillips Screw Driver
Junction Box and (2)Mounting Screws
(supplied by others)
Mounting Plate
Canopy
Ground Screw
(3) Cable
Coupler
Power Cord and (2) Strain Reliefs
(3) Suspension Cables
(3) Cable Grip
Luminaire
1. Remove center support ring per Figure A.
2. Install options per Figure B.
3. Reinstall center support ring per Figure C.
4. Screw (3) Cable Grips into back plate of Luminaire.
5. W
ire Power Cord into Luminaire and connect (1) Strain Relief
into Luminaire.
6. Install Mounting Plate onto Junction Box with (2) mounting
screws.
7. Connect Power Cord into Junction Box through Canopy and
Mounting Plate. Connect Grounding Bolt.
8. C
onnect (1) Strain Relief into Canopy and push Canopy flush
with ceiling or Junction Box.
9. Screw (3) Cable Couplers into Mounting Plate through the
Canopy.
(3) Cable Grip
Luminaire
Figure A
Figure C
Figure B
Luminaire
Collector Lens
(CL) Option
Spacer Ring
(W) Option
Opal Glass
Diffuser (GD)
Option
CLICK!
Perforated Center
Plate (PC) Option
Solid Center
Plate
Center Ring
CAUTION
DANGER
LED Radiation.
Hazardous voltage.
Do not operate while LEDs
are exposed.
Only work on de-engergized
equipment. Disconnect
power before wiring fixture.
Do NOT stare into Beam.
Can cause eye damage.
Contact will cause
electric shock or burn.
Selux Corporation © 2015, T 845-834-1400, 800-735-8927, F 845-834-1401, www.selux.us
Please Note: Disconnect electricity to fixture before working. To be performed by trained personnel only. It is the responsibility of the installer to ensure all electrical, mechanical, and thermal compatibility of the installation site and luminaires prior to installation. Please observe all relevant building codes and regulations.
Keep these instructions after unpacking fixture. For indoor use only. For detailed spec sheets and more information on this and our full range of products, please
visit our website at selux.us. Warranty information: http://www.selux.us/en/resources/terms-and-warranty.html
NOTICE
Do not touch LED
May damage device
Observe precautions for
handling electrostatic
sensitive devices.
Page 3 of 3
(Rev. 09/15)
CERL_INST_v2.0