Previous Page | Return to Index | Next Page
STRAIGHT MINIATURE POWER JACKS
1. 712A
2. PC712A
3. 2C1072
4. L722A
click here to download a schematic drawing
(you will need to have Adobe Acrobat installed on your system to do this)
FEATURES
*2 conductor jack.
*Automatic switch over from AC to DC permitted by sleeve shunt spring.
*Split center pin shaped to hold mating plug firmly. (732A available in solid center pin
only.)
*Choose solder lug or PC terminal. (732A not available in PC terminal.)
*Bushing length available as .219" or extended .319 to permit use in thicker panels. (732A
not available in extended length.)
*L712A and PCL712A accept plugs with .475" long, 0.099" diameter sleeve.
*L722A and PCL722A accept plugs with .475" long, 0.08" diameter sleeve.
*Non-turn mounting possible using standard
*"D" shape bushing.
MOUNTING
Part Numbers 712A, 722A and 732A - Mounts in .313 inch diameter hole in panels up
to .125 inches thick (maximum).
Part Numbers PC712A and PC722A - Same as 712A. See drawing for PC board layout.
Part Number 2C1072 - Jack covers for 712A, 722Aand 732A - special order only.
For insulated mounting, two insulated washers are available on special order. Mounting
hole diameter is .375 inches. See "Insulated Mounting" drawing.
Part Number P2442 - Phenolic flat washer.
Part Number S4263 - Swedged fiber washer.
SPECIFICATIONS
MECHANICAL
Life: 10,000 insertion/withdrawal cycles minimum.
Insertion/Withdrawal Forces: 3 pound insertion (maximum), 4 ounce minimum
withdrawal.
Part Numbers 712A, PC712A, 722A, PC722A, 732A
ELECTRICAL
Contact Resistance: .01 ohms maximum (initial),
.02 ohms maximum (after humidity, durability exposure),
.1 ohms maximum (after salt spray).
Insulation Resistance: 10,000 M(omega) minimum (initial),
1,000 M(omega) minimum (after humidity, durability exposure).
Dielectric Withstanding Voltage: 500 V AC maximum.
Contact Rating: 5 A, 12 V DC. resistive.
MATERIAL
Housing: Molded plastic.
Mounting Bushing and Hex Nut: Plated copper alloy.
Pin, Spring and Terminals: Plated copper alloy.
Insulators: Rigid plastic.
Hardware: Supplied with one Number P2439
nickel-plated brass hex nut, and one Number P2441
nickel-plated steel flat washer.
Part
Number
Description
712A
PC712A
L712A
722A
PC722A
L722A
732A
Solder lugs
PC terminals
Longer Bushing
Solder lugs
PC terminals
Longer Bushing
Solder lugs
Outside
Diameter*
Typical
Mating
Plug**
0.1 inches
(.097-.099)
760
760K
761K
0.08 inches
(.075-.077)
S760
S760K
S761K
0.05 inches
860
* Center pin diameter.
** Other mating Plugs are available.
MM CONVERSIONS
Catalog Dimension
Series
+ tol/-tol Range mm equivalent Use
PC712A 0.156
0.150
0.062
0.040
3.9624
3.81
1.5748
1.016
3.96
3.81
1.57
1.02
0.406
10.3124
10.31
0.216
0.446
0.46875
5.4864
11.3284
11.90625
5.49
11.33
11.90
Previous Page | Return to Index | Next Page
To search a category please click on the corresponding icon:
| Connectors | Jacks and Plugs |
| Patch Panels, Patch Kits & Jackfields | Cable Assemblies and Patch Cords | Switches |
All products shown are covered by Switchcraft's limited lifetime warranty.
| Switchcraft home |
About Us | Products | What's New | Search | Contact Us