ALPU-ALVR
UL 497 Listed - Primary Advanced Lightning Protection
Unit for 55V WiMAX & Power
Over Ethernet Applications
The ALPU-ALVR is purpose built for Alvarion WiMAX and
WiFi Ethernet radios and meets the new UL 497 standards.
ALPU-ALVR is the premier primary and secondary protector
for your high-speed packet network equipment from
lightning and other transients. It is the only Alvarion UL 497
listed protector for primary protection. The ALPU-ALVR
has low capacitance/impedance and insertion loss so that
your packets will reach their destination without disruption
from your surge protection system. The ALPU-ALVR is
configured with three types of surge protection: silicon
diodes for over-voltage, fuses for power line cross, and PTC
(positive temperature coefficient) fuses for sneak current.
Applications
Wireless Broadband Networks
•
WiMAX
•
WiFi
•
MESH
•
Wireless Backhaul
Data
Service Voltage
Cable Entry/Exit
Voltage Protection
Level
55VDC
BreezeAccess
2
130Vpk @ 150A 10/1000μs
BreezeNet
152Vpk @ 1500A 8/20μs
90VDC
Response Time (Max.)
<5 Nanoseconds
Operating Temperature
-40° to +80°C
Part Number
BreezeMax
2 Ethernet
Max. Cont. Operating
Max. Cont. Current
ALPU-ALVR
Alvarion Radio Models
Configurations
1 AMP
1101-640
This product is available through Transtector distributors Anixter, Hutton, Tessco
and WinnCom.
Features
UL 497 Listed
• Surge Protection - over voltage, sneak current and fault current
• Minimal capacitance/low impedance
• Purpose-built for Alvarion broad- band wireless equipment
Primary Surge Protector
Warranty
Five (5) year unconditional warranty
TA BLE 1
P U Tyear
/ O Umanufacturer’s
T P U T W IR IN G warranty
U S IN G ID C
TenIN(10)
• 100 percent, non-degrading silicon suppression
• Appropriate for primary and secondary protection
T E R M IN A L / P O S T
+ D A TA D C +
1
-D A T A D C +
2
+ D A TA D C 3
-D A T A D C 4
D C 4 TX +
5
D C 5 TX 6
6.5”h X 4.7”wD C
X 2.6”d
7 RX+
7
D C cm
8 RXX 6.6
- cm 8
13.9 cm X 12.1
Dimensions:
T E R M IN A L S T R IP S
D E S C R IP T IO N
D C 2 ( -)
D C 2 ( -)
D C 2 ( -)
D C 2 ( -)
D C 2 ( -)
D C 2 ( -)
D C 2 ( -)
D C 2 ( -)
Installation
Remove the cover by loosening the four captive cover screws using a Phillips
screwdriver. Mount the ALPU-ALVR as close to the equipment to be protected
as possible using the provided hardware and the concealed mounting holes.
Mount the unit in the orientation shown.
CONCEALED
MOUNTING HOLES
Thread a multiconductor cable from the data source through the strain relief
adjacent to the marking on the PCB labeled “Input.”
Strip back the cable jacket as needed, then install the conductors into the IDC
connectors labeled “Input” - place the wires into the grooves in the connector,
leaving approximately 1/8” of wire overhanging, and press down firmly with the
punch-down tool until the wires firmly engage into the fork terminals.
Repeat this procedure for the outgoing multiconductor cable, using the
connectors labeled “Output.
EXTERNAL GND LUG
ACCEPTS 4-14 AWG
Tighten the strain reliefs to secure the cables (DO NOT OVER TORQUE!).
Replace the cover.
STRAIN RELIEF ACCEPTS
CABLE DIA. RANGE
0.250" THRU 0.375"
208.772.8515 800.882.9110 FAX 208.762.6133
10701 N. Airport Road, Hayden, ID 83835
www.transtector.com sales@transtector.com
An ISO 9001:2000 and 14001 Certified Company
1453-036 Rev. A