Wireless Control Module

advertisement
www.encelium.com
Wireless Control Module
ENCELIUM Wireless and
ENCELIUM GreenBus II®
Communication Networks
ENCELIUM® Energy Management System – Hardware
Key Features & Benefits
—— Control module for all of the following: —— Connects 0-10V dimmable
luminaires to network for:
– 0-10V dimmable luminaires
–Customizing lighting scenes for – DALI ballasts
tailored experiences/tasks
– Occupancy sensors
–Adjusting light levels to respond —— ENCELIUM GreenBus II® connection
to variable lighting requirements
available for GreenBus II devices
ENCELIUM Wireless Energy Management
System Architecture
WM
SIM
WCM
OSRAM offers a special Damp-Rated (DR) WCM for installations
subject to moderate degrees of moisture.
The WCM is compatible to ENCELIUM hardwired products via the
GreenBus II port on the device. This enhances the flexibility of the
system to include phase-cut dimming, area lighting control and
relay panel control.
C
UL
US
LMS103R1 7-15
er &
Pow g
Line itch le
w
to s
ALC
g
min
Dim
FLOOR 2
Light Fixture
WCM
GreenBus II®
®
Tenant Ethernet Polaris 3D /PCS/PCW
Network
er
Pow
Line
Wireless
Sensor
EN-RPM-24C-GB2
Relay
Panel
Module +50ºC
Item
No 45268
Max
ambient
temperature
Input:
Only40V
24V
AC,
50/60Hz,
AClass 2 min
Energy
Management
Equipment
Subassembly
Emergency
Lighting
and Power
Equipment
6NA8
Made
in Canada
2012
2013
2014
Q1
QQ
2 2015
Q
3 and
4 installation
Install
per
instruction
sheet
electrical
&
building
codes.
to ENCELIUM
GreenBusII
. Connect
only
CAUTION
To
Reduce
- System
theOf
Risk
of
Fire
or
Electric
Shock Do Not
Interconnect
The
Outputs
Dif
ferent
Class
2 Circuits
Relay Panel
WCM
PCDM
ut
se C tures
ix
Pha
AC ming F
Dim
Wireless
Wall Station
PoE Switch
ENCELIUM Ethernet Network
The WCM switches a fixture ON or OFF via a relay contained in the
module as well as delivers a low voltage dimming signal to any 0-10V
dimming ballast/driver. A WCM can be connected to LED drivers
without isolation between the dimming section and the electrical
output for added flexibility in LED driver options.
Low-Voltage
Sensor
Router
FLOOR 1
The Wireless Control Module (WCM) is a key component of the
ENCELIUM Energy Management System (EMS). This device allows
luminaires and occupancy sensors to communicate via a mesh
network based on ZigBee® standards. Individually addressable, the
WCM enables each ballast or LED driver to be independently controlled
and configured to best meet the needs of the facility.
Light Fixture
85-1
16-DA
WCM
WM
Polaris 3D®
SSU
System Architecture
This illustration shows how each component is easily integrated into the ENCELIUM
Wireless Energy Management System (EMS). The ENCELIUM Wireless system communicates via a mesh network based on ZigBee standards. The WCM is powered by incoming line voltage. Each WCM, sensor, and wallstation uses a wireless mesh network to
relay data back to the Wireless Manager (WM). WMs typically control individual floors
and are linked via an Ethernet Network back to the SSU. Internet or LAN connection
allow floor plan based control software via Polaris 3D ® to be operated anywhere on the
network. For reference, the component shown on this data sheet is highlighted.
Ordering Information
Item Number
45572 45583
Ordering Description
EN-WCM-ZB-DR EN-WCM-ZB Communication Network ZigBee® Wireless
ZigBee Wireless
Modifiers
- Damp-Rated -DR
Specifications
—— 3.17" x 1.64" x 1.27"
(80.42mm x 41.6mm x 32.31mm)
—— Operating temperature range: -40°C (-40°F) to 60°C (140°F)
—— Suitable for luminaire or junction box mounting in standard
1/2" knockout (7/8" dia.)
—— Absolute Maximum Ratings 300W (all rated voltages have a tolerance
of +/-10%):
– 4.5A 120-347 Vac Ballast/LED Driver
– 5.8A 120-347 Vac Tungsten
– 9.0A 120-347 Vac General Purpose
—— Single 0-10V dimming output (IEC 60929 Annex E). Capable of sinking
10mA (this is equivalent to 10 typical dimming ballasts/drivers)
—— Standard units are for indoor use only or for mounting inside waterproof
enclosure
—— Damp-rated units may be used in damp locations
—— Radio Properties - 2.4 GHz
—— Wireless Range: 100' line of sight, 50' through standard walls when
WCM is mounted exterior to the luminaire
– Range decreases by 50% when mounted inside the luminaire
—— Safety approvals:
– Energy Management Equipment (UL 916)
– Emergency Lighting Equipment (UL 924 cULus Listed)
– Heat and Smoke Release for Air-Handling Spaces (UL 2043)
—— 0-10V or DALI connectivity
—— ENCELIUM GreenBus II connection port for GreenBus II devices
—— Complies with the following electromagnetic requirements:
– EN 61000-4-2
– EN 61000-4-4
– EN 61000-4-5
—— FCC Part 15/ICES-003
1.64”
(41.60mm)
0.96”
(24.31mm)
1.23”
(31.31mm)
1.27”
(32.31mm)
Dimensions
3.17”
(80.42mm)
Installation Diagram
The mechanical construction allows for simple installation of the WCM
to an available 1/2 inch knock-out on the side or on top of a fixture
(as shown below). All necessary wiring for the electronic dimming
ballast or LED driver is available on the inside.
Fixture Mounting
For some installations, a junction box may be required. It is
recommended to securely mount the WCM to the junction box
(as shown below) using an available 1/2 inch knock-out
and a retainer nut.
J Box Mounting
M
WCM
WC
re
u
Fixt
Wiring Diagrams
Wiring to Luminaire
Wiring to Low Voltage Sensor
LINE
BLACK
NEUTRAL
RED
VIOLET
GREY
BLUE
VIOLET/ +
GREY/ BLUE
NEUTRAL
Power Feed
NEUTRAL
LINE
Power Feed
BLACK
NEUTRAL
RED
VIOLET
GREY
BLUE
0-10V ELECTRONIC
BALLAST/DRIVER
NOT USED
VIOLET/ +
GREY/ BLUE
NOT USED
POWER
COMMON
SIGNAL
Wiring Using GreenBus II Port Only
Power Feed
LINE
INPUT
RED BLUE
INPUT
RED BLUE
INPUT
RED BLUE
INPUT
RED BLUE
INPUT
RED BLUE
WCM
INPUT
RED BLUE
INPUT
RED BLUE
TM
OUTPUT
OUTPUT
3 GreenBusII . Connect to
Energy
Management System only.
OUTPUT
OUTPUT
2 Power fail input
INPUT
RED BLUE
3
1 Power supply input
24V AC, 60Hz, 1.6A (40VA)
Class 2 only
OUTPUT
INPUT
RED BLUE
2
2
4
6
8
10
12
14
16
18
20
22
24
Relays
OUTPUT
OUTPUT
INPUT
RED BLUE
OUTPUT
OUTPUT
INPUT
RED BLUE
OUTPUT
OUTPUT
INPUT
RED BLUE
INPUT
RED BLUE
OUTPUT
OUTPUT
4
1
1
3
5
7
9
11
13
15
17
19
21
23
Relays
INPUT
RED BLUE
INPUT
RED BLUE
OUTPUT
OUTPUT
or
OUTPUT
or
INPUT
RED BLUE
PCDM
ALC
NEUTRAL
Relay Panel
blue
red
2013
Q2
2014
Q3
2015
Q4
INPUT
RED BLUE
Energy Management
Equipment Subassembly
Emergency Lighting
and Power Equipment
INPUT
RED BLUE
Q1
INPUT
RED BLUE
INPUT
RED BLUE
INPUT
RED BLUE
INPUT
RED BLUE
INPUT
RED BLUE
2012
OUTPUT
OUTPUT
6NA8
Made in Canada
OUTPUT
OUTPUT
Item No 45268
OUTPUT
OUTPUT
EN-RPM-24C-GB2
Relay Panel Module
Max ambient temperature +50ºC
Input: Class 2 Only
24V AC, 50/60Hz, min 40VA
Install per installation instruction
sheet and electrical & building
codes. Connect to ENCELIUM
GreenBusII System only.
CAUTION - To Reduce the Risk
of Fire or Electric Shock Do Not
Interconnect The Outputs Of
Different Class 2 Circuits
85-116-DA
OUTPUT
Depress with tool to unlock
LED Always On -> 24V and GreenBusII TM Present
LED Single Blink -> Only GreenBusII TM Present
LED Double Blink -> Only 24 VAC Present
OUTPUT
black
blue
red
GE
Relays
INPUT
RED BLUE
4 Manual Toggle Button
WR
Relays
BLACK
NEUTRAL
RED
VIOLET
GREY
BLUE
VIOLET/ +
GREY/ BLUE
NOT USED
NOT USED
NOT USED
Wire Table
Wire Color
BLACK
RED
WHITE
VIOLET
GREY
BLUE
Wiring to Luminaire
Line In - Relay Contact
Line Out - Relay Contact
Neutral
Class 2, Low Voltage, 0-10Vdc, 10mA max.
Class 2, Low Voltage Return/Common
Not Used
Note: GreenBus II port can also be used when wiring to a luminaire.
Americas Headquarters
OSRAM SYLVANIA Inc.
100 Endicott Street
Danvers, MA 01923 USA
Phone1-888-531-7571
www.encelium.com
OSRAM is a registered trademark of OSRAM GmbH.
ENCELIUM, GreenBus II and Polaris 3D are registered trademarks.
ZigBee is a registered trademark of ZigBee Alliance.
Specifications subject to change without notice.
© 2015 OSRAM
Wiring to Low Voltage Sensor
Line In - Relay Contact
Not Used
Neutral (WCM Input Only)
Power
Common
Signal
Wiring Using GreenBus II Port Only
Line In
Not Used
Neutral
Not Used Not Used Not Used Wire Length
9.84" (250mm)
9.84" (250mm)
9.84" (250mm)
23.62" (600mm)
23.62" (600mm)
7.09" (180mm)
Download