Models: ACSP-3001-HW, ACSP-3001-IG-HW
COMPAC® 30A Surge Suppressor hardwired
Description
The COMPAC® advanced surge suppressor provides the highest current capacity available in devices of its size to protect
multiple pieces of sensitive electronic equipment on a single
circuit. It features industrial strength “zero failure” technology
backed by a ten year warranty. The compact body has a very
low profile (1.75"H x 6"D x 9"W) and includes two multi-mount
brackets to promote easy installation — on a wall behind a flat
panel TV, under a counter, in a rack or just about anywhere.
Terminates to 6-ft. non-metallic flexible whip that can be fieldcut to shorter lengths. A blank plate with knockout allows the
30A receptacle to be converted to hardwired output if desired.
• Model No. ACSP-3001-HW: features (1) 30A outlet
• Model No. ACSP-3001-IG-HW: features (1) 30A insulated
ground outlet
Includes a 6-ft. non-metallic flexible
whip and multi-mount brackets.
Features
• ETL Listed, ANSI C62.41 Compliant
• Conforms to UL1449-3
• Includes blank cover plate with knockout that allows the
30A receptacle to be changed to hardwired output
• Low-profile chassis (1.75”H x 6”D x 9”W)
• LEDs provide visual system status
• Suppresses line to neutral with no ground contamination.
• TCR® technology defeats surges up to 72,000 amps with
zero failures
• Two multi-mount brackets allow versatile installation
• Terminates to 6-ft. non-metallic flexible whip
• 10 year warranty
Mechanical Specifications:
Dimensions:
Weight:
Input Connections:
Output Connections:
Chassis:
Mounting Options:
Performance Specifications:
Operating Voltage/Current:
Maximum Surge Current:
Initial Clamping Voltage:
Endurance:
Transient Noise Reduction:
Response Time:
Temperature Range:
Protection Mode:
UL1449-2 Adjunct Results:
A & E Specifications
The 30A single-circuit surge suppressor shall be Lowell model
__________ with one outlet. It shall be ETL Listed and conform to UL1449-3. It shall meet ANSI C62.41 and protect line
to neutral without ground wire contamination. It shall be capable of protecting electronic equipment from transient voltages,
spikes and surges up to 72,000 amps and have a response
time of less than 5 nanoseconds. It shall surface or rear rackmount using multi-mount brackets. It shall include LEDs for visual ground verification and surge diagnostics.
[Model ________ shall include insulated ground outlets.]
Model No.
Description
ACSP-3001-HW
ACSP-3001-IG-HW
COMPAC surge suppressor
COMPAC surge suppressor
Spec. No. 1127
(rev. 2.22.11)
pg. 1 of 2
Federal GSA specs (1996)
Diagnostic LEDs (surge)**
Applicable Standards:
Safety Agency Approvals:
9"W x 1.75"H x 6"D
5 lbs.
6-ft. non-metallic flexible whip
(1) 30A receptacle
Steel with black powder epoxy finish
(2) multi-mount brackets for surface or rack
installation.
120VAC / 30A, 60Hz
72,000A (exceeds UL1449-3 6000V, 3000A)
205V, UL rating 400V
IEEE C62.41-1991, B3 (C1), Pulses (lifetime):
1kv≥1,000,000; 3kv≥100,000; 6kv≥5000
29dB@100kHz, 70dB@1MHz
Less than 5 nanoseconds
25˚C (77˚F) nominal
Line to neutral, zero ground leakage
1000 surges, 6000 volts, 3000A, C1, and B3
waveforms (IEEE C62.41), NO FAILURES
Grade A, Class 1, Mode 1
Top (green): ON = ground verified
Center (green): ON = protection active
Bottom (red): ON = protection reduced*
UL1449-3, IEEE standard 587-80 A & B, IEEE
standard C62.41-1991, IEC 1000-4-5-1995
(IEC 801-5).
ETL Listed US and Canada
**TCR® surge suppression technology provides the assurance of Grade A, Class 1, Mode 1
endurance and performance testing plus visual diagnostic LEDs. The ground verified (green
LED), protection active (green LED) should always be ON and the reduced protection (red
LED) should be OFF. In the unlikely event the red LED illuminates, full suppression capability
is NOT immediately or even necessarily compromised. The red LED indicates the overall life
expectancy of the unit may be reduced. Contact Lowell for repair or replacement under the
unit’s ten year warranty.
Outlets
Amperage
Termination
Over/Under Protection
Remote Control Capable
1
1-IG
30A
30A
hardwired
hardwired
No
No
No
No
©2010 Lowell Manufacturing Company, 100 Integram Dr., Pacific MO 63069. Phone–800.325.9660 Fax—
636.257.6606. Lowell makes every effort to provide accurate information while reserving the right to change
specifications and/or improve manufacturing methods without notification. (lowellmfg.com)
Models: ACSP-3001-HW, ACSP-3001-IG-HW
COMPAC® 30A Surge Suppressor hardwired
Top / Front Panel Layout
Includes a 6-ft. non-metallic
flexible whip and multi-mount
brackets.
ACSP-3001-IG-HW
ACSP-3001-HW
Changing from receptacle output to hardwired output
Remove cover, flip over and
remove receptacle plate.
Disconnect receptacle.
Install blank knockout plate
in place of receptacle plate.
Attach conduit with wires to
blank knockout plate or
knockout in side of chassis.
Splice to receptacle wires.
Reassemble.
Multi-Mount Bracket Installation
Surface-mount with
exposed brackets.
Surface-mount with concealed
brackets (behind unit).
Mount to rack rail supports or
10-32 tapped rack rail.
Non-metallic flexible whip can be trimmed in the field
Snip reinforcing rib at desired length. Bend
and carefully cut around conduit without cutting wires inside. Remove excess conduit.
Spec. No. 1127
(rev. 2.22.11)
pg. 2 of 2
Snip 2 or 3 ribs around the connector and
remove connector from excess conduit.
Attach connector to shortened
conduit length.
©2010 Lowell Manufacturing Company, 100 Integram Dr., Pacific MO 63069. Phone–800.325.9660 Fax—
636.257.6606. Lowell makes every effort to provide accurate information while reserving the right to change
specifications and/or improve manufacturing methods without notification. (lowellmfg.com)