Keep your batteries in charge with All-­‐In+Charge For all product, installation, or service questions, please visit www.allincharge.com, or contact us at: All-­‐In+Charge Tow-­‐In+Charge Owner’s Manual & Installation Guide Contact Us 635 County Rd.19 Minnetrista, MN, 55364 Email: customerservice@allincharge.com Web: www.allincharge.com All-­‐In+Charge products are manufactured in the Unites States of America Please give us feedback on our website! ALL-­‐IN+CHARGE, LLC
All-­‐In+Charge, LLC 635 County Rd.19 Minnetrista, MN, 55364 Table of Contents Our Products Safety Precautions………………………………………………….……… 1 All-­‐In+Charge 12/24V Smart Box General Overview & Applications............……………........……….. 2 Charge up to two 12-volt auxiliary batteries
from an alternating (cranking) battery in
series.
Applications (Continued)............…...……………………………....…. 3 Applications (Continued)............…...……………………………....…. 4 Reference Diagram....................………………………………………..... 5 Warranty & General Operation……...……………………………..... 6 All-­‐In+Charge All-­‐Charge Smart Box Installation...................................................………………………...….... 7 Installation (Continued)………….....…………………………………. 8 Charge up to three 12-volt auxiliary batteries
from an alternating (cranking) battery
Our Products and Services…………………………………………….. 9 All-­‐In+Charge Tow-­‐In+Charge System Charge any 12-volt auxiliary battery from an
alternating (car/vehicle) battery in parallel.
Combine the Tow-In+Charge with any
All-In+Charge Smart Box for optimum
charging performance.
9 (Installation Continued)
Battery Feed to Harness Important Notice Please read all safety, operating and installation instructions before installing. Note: A standard 7-way round trailer connector (flat pin) input
has the ability to offer a battery feed when your vehicle’s key is in
the run position. If you have no charge coming from your TowIn+Charge system when plugged in, contact your local vehicle
dealership for an appointment to properly activate this feature.
Personal Safety Precautions
•
Someone should be within the range of your voice or close
enough to come to your aid when working near a lead acid
battery.
•
Have plenty of water and soap nearby in case battery acid
comes in contact with skin, clothes or eyes.
•
Wear complete eye protection and clothing protection. Avoid
touching eyes while working with a battery.
•
If battery acid contacts skin or clothing, wash immediately with
soap and water. If acid enters the eye(s) flood eye(s) with
running cold water for at least 10 minutes and get medical
attention immediately.
•
Never smoke or allow a spark or a flame in the vicinity of a
battery or engine.
•
Be extra cautious to reduce risk of dropping a metal tool onto a
battery. It may spark or short-circuit the battery or other
electrical parts that may cause explosion.
•
Remove all personal metal items such as rings, bracelets,
necklaces, watches, and jewelry when working near a battery. A
battery can produce a short circuit high enough to weld a ring or
any metal, causing serious burns.
•
Never charge a frozen battery.
Tow-­‐In+Charge 7-­‐Way Round Trailer Connector (Flat Pin) Wiring Diagram Tow-­‐In+Charge 5-­‐Way Flat Trailer Connector Wiring Diagram 8 1 Program 2 Add your text here. General Overview The All-In+Charge Tow-In+Charge system is equipped with a standard 7way round trailer connector (flat pin) that allows a 12-volt battery feed
when your ignition key is in the run position. This battery feed offers the
ability to charge your 12-volt batteries while you drive, increasing the
duration of your accessory use when you arrive at your destination.
Tow-­‐In+Charge Installation Note: All-In-Charge LLC is not responsible for any damage that
may occur from improper installation.
All-In+Charge Tow-In+Charge systems can be used to charge any type of
12-volt battery.
Install All-In+Charge Tow-In+Charge only per manufacturer
installation instructions.
All-In+Charge Tow-In+Charge systems offer the ability to charge 12-volt
batteries that have limited or no charging access.
All-In+Charge Tow-In+Charge systems work by using power already
generated (reusable energy), helping save on the costs of electricity used
by AC chargers, and gas for gas-powered generators.
All-In+Charge Tow-In+Charge systems can be used to charge your
cranking batteries in parallel as you tow, as well as other 12, 24, or 36-volt
applications when coupled with a specific All-In+Charge Smart Box.
Patented All-In+Charge technology helps prevent damage to batteries
caused by heat generation.
All-In+Charge Tow-In+Charge systems work in tandem with AC chargers,
helping maintain the charging of your batteries while you are driving
Applications All-In+Charge products should not void any warranties on batteries,
motors, or any other equipment. Please contact us with any
questions or concerns.
Connection Precautions a.) All-In+Charge Tow-In+Charge systems will only charge 12-volt
batteries. Do not connect the output of the charger to any other voltage
or type of battery.
b.) Clean battery terminals. Be careful to keep corrosion from coming in
contact with eyes.
c.) Check polarity of battery posts. POSITIVE (POS, P, +) battery post is
usually larger in diameter than NEGATIVE (NEG, N, -) post.
Tow-­‐In-­‐Charge Wiring Installation a.) Run your Tow-In+Charge wiring to its battery’s destination to see how
All-In+Charge Tow-In+Charge in-tow applications include, but are not
limited to:
•
•
•
•
•
•
•
•
For your local All-In+Charge installer, please visit our website at
www.allincharge.com.
b.)
Boating (cranking) batteries
ATV/snowmobile batteries
Motorcycle batteries
Heavy equipment batteries
Farm equipment batteries
Fish house batteries
Dump trailer batteries
RV trailer (house) batteries
much length you will need before securing quick connectors to an easy
accessible area
(Optional) Once you have adequate wire length to connect your wires
easily to your battery, secure your Trailer Quick Connecters to an easily
accessible area by using a 1/8" drill bit to drill pilot holes in the
mounting locations. Add silicon sealer in each of the mounting
locations to waterproof the screw holes. Position your Trailer Quick
Connectors over the mounting holes and secure with a power
screwdriver by installing marine grade or stainless steel screws
(mounting screws not included).
c.) Connect red wire from the Tow-In+Charge to positive terminal on
“alternating (cranking)” battery.
d.) Connect black wire from the Tow-In+Charge to negative terminal on
“alternating (cranking)” battery.
2 7 Warranty
All-In+Charge products come with a 30-day money back guarantee & 3 year
limited warranty. Visit www.allincharge.com for more details.
(Applications Continued)
General Operation
Snowmobile Batteries
Properly installed, your Tow-In+Charge system will charge your alternating
(receiving) 12-volt battery no higher than the voltage stemming from your main
alternating (car) 12-volt battery, reducing the chance of overcharge on your
batteries or heat generation that may cause damage to other surrounding
equipment.
When your main alternating (car) 12-volt battery is alternating power, your
Tow-In+Charge will automatically charge and help extend the life your auxiliary or
cranking batteries while towing.
ATV Batteries
Important Notice Make sure that Tow-­‐In+Charge Quick Connectors are detached between your trailer and towing vehicle before launching or detaching! Quick Connectors to be detached may depend on how Tow-­‐In+Charge wiring is custom installed. Motorcycle Batteries
If you are charging batteries that are secured to an ATV or any other kind of mobile vehicle, make sure that the Terminal Connections are free of the battery terminals before moving your mobile vehicle. Trailer Quick Connectors Fish House (House) Batteries
Harness Quick Connectors 6 3 (Applications Continued)
Dump Trailer Batteries
Reference Diagram •
7-Way Round Trailer Connector
Harness (Flat Pin)
•
5-Way Flat Vehicle Connector
•
Harness Quick Connectors
•
Trailer Quick Connectors
Boat Batteries
RV Trailer (House Batteries)
•
Terminal Connections
Cranking Battery 4 5