INSTALLATION AND
OPERATING INSTRUCTIONS
REFRIGERATOR FOR LP-GAS AND ELECTRIC OPERATION.
RM 2620 RM 2820
FOR YOUR SAFETY
If you smell gas:
1. Open windows.
2. Don’t touch electrical switches.
3. Extinguish any open flame.
4. Immediately call your gas supplier.
Contents:
Installation
Operating Instructions
Maintenance & Service
Page
4
7
11
FOR YOUR SAFETY
Do not store or use gasoline or other
flammable vapors and liquids in the
vicinity of this or any other appliance.
WARNING: Improper installation,
adjustment, alteration,service or
maintenance can cause injury or
property damage. Refer to this
manual. For assistance or additional
information consult a qualified
installer, service agency or the gas
supplier.
AVIS
Cet appareil doit être réparé
seulement par un réparateur
autorisé. Modification de
l’appareil pourrait être
extrèmement dangeruse, et
pourrait causer mal ou mort.
Corporate Office
2320 Industrial Parkway Elkhart, IN 46515
USA
Service Office
The Dometic Corporation
509 South Poplar Street
LaGrange, IN 46761
Phone: 219-463-4858
825 12 03-00
For Service Center Assistance
Call: 800-544-4881
CANADA
Dometic Distribution Inc.
866 Langs Drive
Cambridge,Ontario
N3H 2N7 Canada
Phone: 519-653-4390
Heater
Flue baffle
Protection
cover
Power module
cover
Burner jet
12 Volt
Terminal block
Evaporation tray
Inlet fitting
Manual gas
shutoff valve
Drip pan
Flexible cord
FIG. 1
Refrigerator control panel.
A
1
D
3
2
B
C
E
F
LEGEND 2-WAY AMES Model
1. Main Power Button ON/OFF
2. AUTO/GAS Mode Selector Button
3. Temperature Selector Button
A. AUTO Mode Indicator Lamp
B. AC Mode Indicator Lamp
C. GAS Mode Indicator Lamp
D. CHECK Indicator Lamp
(GAS Mode Only)
E. Temperature Indicator Lamps
F. Climate Control Switch
FIG. 2
3
INSTALLATION
GENERAL INSTRUCTION
This appliance is designed for storage of foods
and storage of frozen foods and making ice.
The refrigerators outlined herein have been design certified by A.G.A. under the ANSI Z21.19 Refrigerator
Standard for installation in a mobile home or recreational
vehicle and are approved by the Canadian Gas Association.
The certifications are, however contingent on the installation being made in accordance with the following
instructions as applicable.
In the U.S.A., the installation must conform with:
1. National Fuel Gas Code ANSI Z223.1-(latest edition)
2. Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280.
3. Recreational Vehicles ANSI A119.2-(latest edition).
The unit must be electrically grounded in accordance
with the National Electric Code ANSI/NFPA 70-(latest
edition) when installed, if an external alternating current
electrical source is utilized.
4. Any applicable local code.
In CANADA, the installation must conform with:
1. Current CAN/CGA B 149 Gas Installation Codes
2. Current CSA Standard Z 240.4 GAS-EQUIPPED
RECREATIONAL VEHICLES AND MOBILE HOUSING.
3. Where a flexible metal connector is used, it must
comply with the provisions of the current Standard
CAN1-6.10, METAL CONNECTORS FOR GAS
APPLIANCES
4. Any applicable local code
The unit must be electrically grounded in accordance
with the current CANADIAN ELECTRICAL CODE C 22
Parts 1 and 2.
GAS CONNECTION
Hook-up to the gas supply line is accomplished at the
manual gas valve, which is furnished with a 3/8" SAE
(UNF 5/8" -18) male flare connection. All completed
connections should be checked for leaks with soapy
water.
! WARNING
DO NOT use a flame to check for gas leaks.
The gas supply system must incorporate a pressure
regulator to maintain a supply pressure of not more than
11 inches water column.
When testing the gas supply system at test pressures in
excess of 1/2 psig, the refrigerator and its individual
shutoff valve must be disconnected from the gas supply
piping system.
When testing the gas supply system at pressures less
than or equal to 1/2 psig, the appliance must be isolated
from the gas supply piping system by closing its individual
manual shutoff valve.
In case detailed instructions on the installation and
connection to the gas supply are required, contact your
dealer or distributor.
ELECTRICAL CONNECTION
120 Volts AC Connection
The refrigerator is equipped with a three- prong (grounded) plug for protection against shock hazards and should
be plugged directly into a properly grounded threeprong receptacle. DO NOT cut or remove the grounding
prong from this plug. The free length of the cord is 2 feet
and therefore recommended that the receptacle be
located to the left side of the refrigerator (viewed from
the rear) and approximately 6 inches from the floor (see
FIG. 3). This allows easy access through the vent door.
The cord should be routed to avoid direct contact with
the burner cover, flue cover or any other components
that could damage the cord insulation.
VENTILATION
The installation shall be made in such a manner as to
separate the combustion system from the living space
of the mobile home or recreational vehicle. Openings for
air supply or for venting of combustion products shall
have a minimum dimension of not less than 1/4 inch.
Proper installation requires one lower fresh air intake
and one upper exhaust vent. The ventilation kits shown
in this instruction manual have been certified for use with
the refrigerator models listed in the table. For "Certified
Vent System Kits" see page 15. The ventilation kits
must be installed and used without modification. An
opening toward the outside at floor level in the refrigerator compartment must be provided for ventilation of
heavier-than-air fuel gases. The lower vent of the recommended kits is provided with proper size openings. The
flow of combustion and ventilating air must not be obstructed.
The lower side vent is fitted with a panel that provides
an adequate access opening for ready serviceability of
the burner and control manifold of the refrigerator.
4
120 Volt AC
receptacle
6"
FIG. 3
12 Volts DC Connection
This refrigerator model is not designed for 12 volt DC
operation of the cooling system; however, a continuous
12 volt DC must be supplied to the refrigerator to operate
the controls. Use a minimum of a 14 gauge wire
between the battery and refrigerator to supply the
control voltage. The connection is made to the positive
(+) and negative (-) terminals of the terminal block on
the back of the refrigerator. (See FIG. 1).
Correct polarity must be observed when connecting to
the DC supply.
DO NOT use the chassis or vehicle frame as one of the
conductors. Connect two wires at the refrigerator and
route to the DC supply.
INSTALLING REFRIGERATOR IN
ENCLOSURE
NOTE: DO NOT install the appliance directly on
carpeting. Carpeting must be removed or
protected by a metal or wood panel beneath the appliance which extends at least
full width and depth of the appliance.
The refrigerator must be installed in a substantial enclosure and must be level. When installing the refrigerator
in the enclosure, all areas within the recess in which the
refrigerator is installed must be sealed.
Make sure that there is a complete seal between the
front frame of the refrigerator and the top, sides and
bottom of the enclosure. A length of sealing strip is
applied to the rear surface of the front frame for this
purpose. Also apply a sealing strip to the foremost floor
of the enclosure and apply a second sealing strip to the
bottom of the trim strip on the front base as shown in
FIG. 4. The sealing should provide a complete isolation
of the appliance’s combustion system from the vehicle
interior.
NOTE: Be careful not to damage the sealing strip applied
to the floor of the enclosure when the refrigerator is put
in place.
Securing the refrigerator
After the refrigerator is put in place, (ensuring a combustion seal at the front frame), the refrigerator is to be
secured in the enclosure with six screws. The screws
have to be installed in the following order:
STEP 1: Two Screws installed on front base.
STEP 2: Two Screws installed in the top frame.
STEP 3: Two Screws installed in the rear base.
STEP 4: The refrigerator is provided with a lower front
strip (shipped as a loose part). The front strip is to be
attached after the refrigerator is set into the cutout
opening, and secured with 3 screws. (See FIG. 5).
FIG. 4
3 rd.
2 nd.
1 st.
FIG. 5
4 th.
the refrigerator greater den 1-1/2 inches should be
blocked.
The heat produced at the rear of the refrigerator will
become trapped in this space, making the top of the
refrigerator hot and reduce the efficiency of the refrigerator.
Failure to follow the sequence in securing refrigerator in
enclosure can cause leakage between the frame and
cabinet. Plastic caps are provided to cover the screw
holes in the decoration strip, at the top frame. Any space
between the counter, storage area or ceiling and top of
5
NOTE: The upper vent should be
centered over the condenser coil
at the back of the refrigerator.
TESTING LP GAS SAFETY
SHUTOFF
The gas safety shutoff must be tested after the
refrigerator is connected to LP gas supply.
To test the gas safety shutoff, proceed as follows:
1. Start the refrigerator and switch to GAS mode.
(see start up instructions).
2. Check that the gas flame is lit and the GAS mode
indicator lamp (C) is on.
3. Close the manual gas shutoff valve at the back of the
refrigerator. (See FIG. 1).
4. Wait for one minute. The CHECK indicator lamp (D)
should be on and the GAS mode indicator lamp (C)
should be off.
5. Remove protection cover (see FIG. 1) and open the
manual gas shutoff valve. Do not change any button
positions on the control panel. Apply a non-corrosive
commercial bubble solution to the burner jet orifice.
6. No bubbles should appear at the opening of the
burner jet orifice. The presence of bubbles indicates
a defective gas safety shutoff, and service is required.
7. If no bubbles were present at the burner jet orifice, it
should be rinsed with fresh water. Be careful not to
damage the burner jet orifice. Replace cover and
press the main power ON/OFF button (1) OFF and
back ON. Normal operation of the burner should
return. Allow the burner to operate for a minimum of
five minutes.
Minimum
ventilation
height
Condenser
FIG. 6
CERTIFIED INSTALLATION
Certified installations require one roof vent and one
lower side vent.
For "Certified Vent System Kits" see page 15.
For further information contact your dealer or distributor.
METHODS OF INSTALLATION
The method of installation is shown in FIG. 6. It is
essential that all maximum or minimum dimensions are
strictly maintained, as the performance of the refrigerator is dependent on adequate flow of air over the rear of
the refrigerator.
FIG. 7
VENTILATION HEIGHTS
Installation with roof
vent and lower side vent
Minimum ventilation
heights in
Refrigerator
Inches
mm
54
60
1372
1524
RM 2620
RM 2820
CLEARANCES
Minimum clearances in inches to combustible materials
are:
G: Top
0
K: Side
0
L: Bottom 0
M: Rear
0
N:
See NOTE: Clearance "N" below.
NOTE: Clearance "M" is between the rearmost part of
the refrigerator and the wall behind the refrigerator.
6
NOTE: Clearance "N" is the distance between the bottom of the lower vent to the roof material. For ventilation
height, see table VENTILATION HEIGHTS
See Figures 6, and 7.
View from above
Side view
C
D
D
W
B
A
H
FIG. 8
Overall
Dimensions
Refrigerator
Model
Recess
Dimensions
inch
Height
A
51-31/32
Width
B
22-23/32
Depth
C
24-9/16
Height
H
49-17/32
Width
W
21-13/16
Depth
D
24-3/32
mm
inch
1320
57-7/8
577
24-39/64
624
24-9/16
1258
55-7/16
554
23-11/16
612
24-3/32
mm
1470
625
624
1408
601
612
RM 2620
RM 2820
This method of installation and these clearances will give you adequate space for service and proper installation.
OPERATING
INSTRUCTIONS
IMPORTANCE OF LEVELING A
REFRIGERATOR
In an absorption refrigerator system, ammonia is liquefied in the finned condenser coil at the top rear of the
refrigerator. The liquid ammonia then flows into the
evaporator (inside the freezer section) and is exposed
to a circulating flow of hydrogen gas, which causes the
ammonia to evaporate, creating a cold condition in the
freezer.
The tubing in the evaporator section is specifically
sloped to provide a continuous movement of liquid
ammonia, flowing downward by gravity through this
section. If the refrigerator is operated when it is not level
and the vehicle is not moving, liquid ammonia will
accumulate in sections of the evaporator tubing. This will
slow the circulation of hydrogen and ammonia gas, or in
severe cases, completely block it, resulting in a loss of
cooling.
Any time the vehicle is parked for several hours with the
refrigerator operating, the vehicle should be leveled to
prevent this loss of cooling. The vehicle needs to be
leveled only so it is comfortable to live in (no noticeable
sloping of floor or walls).
When the vehicle is moving, the leveling is not critical,
as the rolling and pitching motion of the vehicle will pass
to either side of level - keeping the liquid ammonia from
accumulating in the evaporator tubing.
OPERATION
Before starting the refrigerator, check that all the manual
gas valves are in the ON position. DO NOT forget the
manual shutoff valve on the rear of the refrigerator see
FIG. 1.
This refrigerator is equipped with a semi Automatic
Energy Selector (AMES) control system, which can
automatically select the most suitable energy source
which is available, either AC or LP gas operation, or if
desired, LP gas only.
The refrigerator controls will work down to 9.6 volt DC.
! WARNING
Most LP gas appliances used in recreational
vehicles are vented to the outside of the
vehicle. When parked close to a gasoline pump,
it is possible that the gasoline fumes could
enter this type of appliance and ignite from the
burner flame, CAUSING A FIRE OR AN EXPLOSION.
FOR YOUR SAFETY, when refueling, shut off all
LP gas appliances which are vented to the outside.
7
Refrigerator control panel.
A
1
C
START UP INSTRUCTIONS
A.
A continuous 12 volt DC supply must be available for
the electronic control to function.
B. Press the main power ON/OFF button (1) to the
DOWN position.
C. Press the TEMPERATURE SELECTOR button (3)
until the lamp at the desired setting is illuminated.
AUTO MODE
2.
3.
Press the AUTO/GAS mode selector button (2) to
turn ON the Auto lamp (A). If 120 volts AC is available,
the AC mode indicator lamp (B) will illuminate indicating AC operation. If 120 volts AC is not available, the
GAS mode indicator lamp (C) will illuminate and the
control system will automatically switch to GAS operation.
If the CHECK indicator lamp (D) illuminates and the
GAS mode indicator lamp (C) is off, the controls have
failed to ignite the burner in the GAS mode. GAS
operation may be reset by pressing the main power
ON/OFF button (1) to the OFF then ON position. (See
step 2 under GAS MODE).
Press the TEMPERATURE SELECTOR button (3)
until the lamp at the desired position is illuminated.
GAS MODE
1.
2.
3.
8
3
2
B
1.
D
Press the AUTO/GAS mode selector button (2) to
turn OFF the Auto lamp (A). The GAS mode indicator
lamp (C) will illuminate. Within 45 seconds the burner
should be ignited and operating normally.
On the initial refrigerator start-up, it may take longer
than 45 seconds to allow air to be purged from the
gas line. If the gas does not ignite within 45 seconds
the CHECK indicator lamp (D) will illuminate and the
GAS mode indicator lamp (C) will go off. To reset
when the CHECK indicator lamp (D) is illuminated,
press the main power ON/OFF button (1) to the OFF
and then ON position.
NOTE: Do not continue to reset GAS operation if the
CHECK indicator lamp continues to be illuminated
after several tries.
Press the TEMPERATURE SELECTOR button (3)
until the lamp at the desired position is illuminated.
E
THERMOSTAT
The thermostat on the refrigerator controls both the gas
and electric operation, thereby eliminating the necessity
of resetting each time a different energy source is
employed.
After the initial start-up, the thermostat should be moved
from "COLDEST" to the desired temperature setting,
usually about mid setting.
TO SHUT OFF THE REFRIGERATOR
The refrigerator may be shut off while in any mode of
operation by pressing the main power ON/OFF button
to the UP (OFF) position. This shuts off all DC power to
the refrigerator, including the interior light.
Refrigerator control panel.
A
1
D
3
2
B
C
DESCRIPTION OF OPERATING
MODES
AUTO MODE
When operating in the AUTO mode, the AUTO mode
indicator lamp (A) will illuminate. The control system will
automatically select between AC and GAS operation
with AC having priority over GAS. Either the AC indicator
lamp (B) or the GAS indicator lamp (C) will illuminate
depending on the energy source selected by the control
system. If the control system is operating with AC energy
and it then becomes unavailable, the system will automatically switch to GAS. As soon as AC becomes available again the control will switch back to AC regardless
of the status of GAS operation.
GAS MODE
When operating in the GAS mode, the AUTO mode
indicator lamp (A) will be off and the GAS mode indicator
lamp (C) will be illuminated. This mode provides LP gas
operation only. The control system will activate the ignition system and will attempt to light the burner for a
period of approximately 45 seconds. If unsuccessful, the
CHECK indicator lamp (D) will illuminate and the GAS
mode indicator lamp (C) will turn off.
E
LIMP MODE OF OPERATION
This control system contains a feature where it will
continue to operate the cooling system in the event of a
failure of a major operating component. Two different
modes of operation can occur in this category.
If for some reason the display module becomes non
functional, the control system will revert to full automatic
operation selecting the best energy source available
with AC, GAS priority. The temperature of the refrigerator
will be maintained at the MID position within normal
temperature tolerances. The power module will continually
attempt to re-establish operation of the display module.
The second limp mode of operation will execute when a
failure of the temperature sensing device or associated
electronic circuitry occurs. If this should occur, the control system will operate on the energy source selected
via the control panel. The cooling unit will run continuously on the selected energy source. The refrigerator
will continue to operate in this mode indefinitely or until
a new sensor is installed and the system is reset.
To restart GAS operation, press the main power
ON/OFF button (1) to the OFF and then ON position. The
control system will attempt a new 45 second ignition
sequence.
If the refrigerator has not been used for a long time or
the LP tanks have just been refilled, air may be trapped
in the supply lines. To purge the air from the lines may
require resetting the main power ON/OFF button (1)
three or four times. If repeated attempts fail to start the
LP gas operation, check to make sure that the LP gas
supply tanks are not empty and all manual shutoff valves
in the lines are open. If the problem is still not corrected,
contact a service center for assistance.
If the control is switched to AC operation while the
CHECK indicator lamp is on, it will function properly, but
the CHECK indicator lamp will not go off until the main
power ON/OFF button is pressed to the OFF then ON
position.
9
HOW TO USE THE REFRIGERATOR
FOOD STORAGE COMPARTMENT
The food storage compartment is completely closed and
unventilated, which is necessary to maintain the required low temperature for food storage. Consequently,
foods having a strong odor or those that absorb odors
easily should be covered. Vegetables, salads etc. should
be covered to retain their crispness. The coldest positions in the refrigerator are under the cooling fins and at
the bottom of the refrigerator. The warmer areas are on
the upper door shelves. This should be considered when
placing different types of food in the refrigerator.
FROZEN FOOD STORAGE
COMPARTMENT
Quick frozen soft fruits and ice cream should be placed
in the coldest part of the compartment, which is on or
just below the freezer shelf. Frozen vegetables, may be
stored in any part of the compartment.
This compartment is not designed for deep or quick
freezing of food. Meat or fish, whether raw or prepared,
can be stored in the frozen food storage compartment
provided they are pre-cooled first in the refrigerator. They
can be stored about three times longer in the frozen food
compartment as compared to the fresh food compartment. To prevent food from drying out, keep it in covered
dishes, containers, plastic bags or wrapped in aluminum
foil.
Ice cubes can be made in the freezer compartment.
For faster ice making, the trays should be placed in direct
contact with the freezer shelf.
Ice will be made more rapidly if the thermostat is set at
its highest position.
It is a good idea to do this a few hours before the
anticipated need for ice, but be sure to move back to
normal setting, usually about mid setting when the ice is
formed. Food in the lower compartment may be frozen
if the setting is left on "COLDEST" position.
Total Refrigerated Volume RM 2620 is 6.0 cu.ft.
Total Refrigerated Volume RM 2820 is 7.7 cu.ft.
DEFROSTING
Shut off the refrigerator by pressing the main power
ON/OFF button to the UP (OFF) position. Empty the
refrigerator, leaving the drip tray under the finned evaporator, and the cabinet and freezer doors open. Filling
the ice trays with hot water and placing them in the
freezer compartment can reduce defrosting time.
! CAUTION
DO NOT use a hot air blower. Permanent damage
could result from warping the metal or plastic parts.
DO NOT use a knife or an ice pick, or other sharp
tools to remove frost from the freezer shelf. They can
create a leak in the ammonia system.
10
When all frost is melted, dry the interior of the refrigerator
with a clean cloth. Replace all food and set the thermostat to the COLDEST temperature setting for a few
hours. Then reset the thermostat to the desired setting,
usually at mid setting.
NOTE: On these models the drip tray/cup is on the rear
side of the refrigerator. (See FIG. 1)
Move the plastic drain tube in to a watertight bucket or
container. (Access through louvered service panel on
the outside of the vehicle.) As the frost melts, the water
will flow into the container. When all the frost has melted
wipe up the excess moisture and empty the accumulated water from the bucket. Replace the drain tube to its
original position.
CLEANING
Cleaning the refrigerator is usually done after it is defrosted or put into storage. To clean the interior liner of
the refrigerator, use lukewarm weak soda solution. Use
only warm water to clean the finned evaporator and
shelves. NEVER use strong chemicals or abrasives to
clean these parts, as the protective surfaces will be
damaged. It is important to always keep the refrigerator
clean.
SHUT OFF - STORAGE PROCEDURE
Shut off the refrigerator by pressing the main power
ON/OFF button to the UP (OFF) position.
If the refrigerator will not be in operation for a period of
weeks, it should be emptied, defrosted, cleaned and the
doors left ajar. The ice trays should also be dried and
kept outside the cabinet.
! WARNING
DO NOT store explosive substances in the refrigerator, such as cigarette lighter gas, petrol, ether or the
like.
CLIMATE CONTROL HEATER
During the summer months of high temperatures and
humidity, the metal frame between the freezer and fresh
food compartments may have water droplets forming.
The number of water droplets will increase if the vehicle
isn’t air conditioned during these months.
This refrigerator comes standard with a 12 volt (DC)
climate control that will evaporate the water droplets
when they form.
To have the climate control on, you position the switch
("F" see figure 2) located beneath the top decoration
panel that houses the control panel to ON. The climate
control can be left on continuously or only used when
temperatures require it.
NOTE: The climate control will draw 12 volts DC power
continuously when in the ON position. It should be turned
OFF when a charging source is not available.
GAS EQUIPMENT ASSEMBLY
INLET FITTING
MANUAL SHUT OFF VALVE.
SHOWN IN OPEN POSITION,
USE A QUARTER DOLLAR OR A SLOTTED SCREWDRIVER TO CHANGE POSITION
SOLENOID VALVE
BURNER MOUNTING SCREWS
THERMOCOUPLE
BURNER JET
FIG. 9
SPARK
ELECTRODE
PRESSURE TEST PORT
ELECTRIC EQUIPMENT
BURNER TUBE
MAINTENANCE & SERVICE
CARTRIDGE HEATER
The heat necessary for the operation of an absorption
cooling unit is supplied by an electric heater mounted in
a pocket of the boiler system.
These models are equipped with one electrical heater
for 120 volt AC.
To replace the heater proceed as follows:
1. Disconnect the wall plug, and the 12 volt wires.
2. Remove the protection cover see FIG. 1
3. Remove the power module cover see FIG. 1
4. Disconnect the heater leads.
5. With a pair of pliers unfold the lug holding the lid of
the boiler casing and open the lid.
6. Remove some insulation wool so that the heater is
accessible.
7. Turn and lift the heater out of its pocket.
8. Fit the new heater into the pocket.
9. Connect the leads and put on the power module
cover.
10. Reset the insulation and close the lid of the boiler.
11. Replace the protection cover.
FUSES
These models are equipped with 2 fuses, one for the
refrigerator control system and one for AC cartridge
heater. (See table below).
To replace fuse(s) proceed as follows.
1. Disconnect the wall plug, and the 12 volt wires.
2. Remove the power module cover. See FIG. 1.
3. Snap the fuse out of the fuse holder.
4. Fit a new fuse in to the fuse holder.
5. Replace the power module cover.
Control system
AC heater
3 Amp
5 Amp
The user should be aware of service that must be
done on a regular schedule to keep the refrigerator
operating properly. The service should only be
performed by a qualified technician who is familiar
with LP gas systems and refrigerators.
1.
REFRIGERATOR REMOVAL
Before working on the refrigerator, make sure the AC
voltage and DC voltage leads are disconnected. Shut
off the gas supply. Disconnect the gas supply line at
the rear of the refrigerator; (see FIG. 1.). Always use
a back up wrench when loosening and tightening this
connection. Cap the gas supply line, loosen the
screws anchoring the refrigerator to the enclosure
and slide the refrigerator out of the compartment.
When replacing the refrigerator make sure that the
sealing strips are properly positioned.
Replacement is the reverse of removal. Check all gas
connections for leaks.
Refer to section INSTALLATION, page 4 to 7.
2.
PERIODIC MAINTENANCE
To keep your Dometic refrigerator operating efficiently and safely, periodic inspection and cleaning of
several components once or twice a year is recommended.
A. It is important to keep the area at the back of the
refrigerator clean. Check the lower vent, upper vent
and area between these openings for any obstructions such as bird/insect nests, spider webs, etc.
Clean the coils on the back of the refrigerator. Use a
soft bristled brush to dust off the coils.
It is important to keep the refrigerator area free from
combustible material, gasoline and other flammable
vapors or liquids.
NOTE: The following maintenance is required once or
twice a year, but should only be done by a qualified
serviceman who is familiar with LP gas systems and
refrigerators.
11
B.
Check all connections in the LP gas system (at the
back of the refrigerator) for gas leaks. The LP gas
supply must be turned on. Apply a non-corrosive
bubble solution to all LP gas connections. The appearance of bubbles indicates a leak and should be
repaired immediately by a QUALIFIED SERVICEMAN WHO IS FAMILIAR WITH GAS SYSTEM AND
REFRIGERATORS.
! WARNING
DO NOT use a wire or pin when cleaning the burner
jet as damage can occur to the precision opening.
This can cause damage to the refrigerator or create
a fire hazard.
! WARNING
DO NOT use a flame to check for gas leaks.
C. Check the AMES control system by connecting/disconnecting 120 volt AC power, start/stop the engine,
etc. Compare the operation with the operation described in description of operating modes. Page 9.
D. The LP gas pressure should be checked and the
main regulator re-adjusted if pressure is incorrect.
The correct operating pressure is 11 inches of water
column. The correct place to take the LP gas pressure is at the test port just ahead of the burner jet.
(See FIG. 9).
E. Inspect the flue baffle. It should be reasonably clean
and free of soot. Heavy soot formation indicates
improper functioning of the burner. The flue and
burner both require cleaning in the following manner:
1. Unplug the refrigerator power cord from the 120 volt
AC outlet. (See FIG. 3).
2. Disconnect or shut off the 12 volt power to the
refrigerator.
3. Turn manual shutoff valve to OFF.(See FIG. 1).
4. Remove cover from the burner housing. (See FIG.
1).
5. Disconnect the wire from the high voltage electrode.
6. Remove the burner mounting screws and remove the
burner assembly. (See FIG. 9).
7. Remove the flue cap from top of flue tube and lift out
the wire and spiral baffle. Clean the flue from the top
using a flue brush. Blowing compressed air into the
flue will not properly clean soot and scale out of the
flue tube. Replace spiral baffle and flue cap.
8. Clean burner tube with a brush. Blow out burner with
compressed air.
9. Before removing burner jet, clean burner area of soot
and scale that fell out of flue tube. Remove the burner
jet. Soak the jet in wood alcohol and blow it out with
compressed air. Re-install and tighten burner jet.
NOTE: The color of the flame shall be clear blue over
the slots of the burner. (See FIG. 10).
10. Reinstall burner, being careful that the end of the
burner fits into the slot on the burner bracket. Check
to make sure slots are centered under the flue tube
and the thermocouple is positioned properly (tip of
thermocouple extends over two slots of burner).
11. Be sure to reconnect the wire to high voltage electrode. Check the electrode for proper location and
gap. (See FIG. 11).
FIG. 11
Electrode
1/8" to 3/16"
(3-5 mm)
Burner tube
12. Turn on manual gas shutoff valve and check all
fittings for leaks.
13. Connect 120 volt power cord to the outlet and reconnect or turn on the 12 volt DC power.
14. Check LP gas safety shutoff. See page 6.
TROUBLESHOOTING
The Refrigerator Does Not Cool Properly
A.
Burner jet clogged.
Clean. (See section Maintenance & Service, Item 2.
Periodic Maintenance, Paragraph E. Item 1-14.
B.
Check level of refrigerator.
C. Venting problem.
Restriction in air flow across cooling unit.
D. Heavy frost buildup on evaporator fins.
Defrost.
Clear blue color
of flame
FIG. 10
12
E.
Flue baffle not inserted properly in flue tube.
F.
Improperly set thermostat.
See section Operating Instructions, part Start Up
Instructions.
G. Burner dirty.
Clean. See section Maintenance & Service, Item 2.
Periodic Maintenance, Paragraph E. Item 1-14.
H. LP gas pressure low at burner.
Set main regulator so pressure does not drop below
11 inches water column at pressure tap.
I.
Burner not located properly under flue tube.
Relocate.
J.
Burner damaged.
Replace.
K.
Odors from fumes.
1. Dislocated burner.
2. Damaged burner.
3. Dirty flue tube.
L.
FUSES
1. Refrigerator AC Supply.
2. Control system. See page 11, part Fuses.
NOTE: AVOID SPRAYING WATER THROUGH THE
REFRIGERATOR VENTS WHILE WASHING YOUR RV.
All the above instructions are to be followed closely. The
refrigerator is quality-guaranteed. However, we are not
responsible for any failures caused by improper adjustments and unfavorable installation conditions. Contact
service point or distributor service dept. for assistance.
FIG. 12
CHANGING DOOR HINGES FROM
ONE SIDE TO THE OTHER
Open the top door and remove the two screws holding
the top decoration. The screws are accessible from
beneath. (See FIG. 12)
Remove the top hinge pin and lift out the top door.
Remove center hinge pin and lift out the lower door.
Unscrew the bottom hinge pin. Remove the plastic cap
from the opposite lower hinge and place it in the hole
just "left empty" by the lower hinge pin. Screw the lower
hinge pin in the hole from which the plastic cap was
removed.
Before replacing the doors on the refrigerator, remove
the catches and move them to the opposite side of the
cabinet. The screw holes are covered with plastic caps
that must be removed and inserted in the screw holes
that previously held the catches. NOTE: The plastic caps
are not installed on new refrigerators and are in the parts
bag.
Remount the doors and hinge pins in the reverse order
of their removal. Unscrew the handles and re-fasten
them on the opposite side of the door. Insert the plastic
caps (from the parts bag) into the holes left open on the
doors. Check the door gaskets. If they are correct, then
replace the top decoration.
13
INSTRUCTIONS FOR MOUNTING
THE DOOR PANEL
The refrigerator is normally delivered without door panels. Before starting the mounting work, check that the
panel dimensions are in compliance with those given in
the table and the instructions are read thoroughly.
When mounting the panel, proceed as follows):
A. On new refrigerators, the decoration strips are taped
inside the door; if installed on the door, remove the
door decoration strip (2) by removing its two screw
(1).
B. Insert one vertical edge into the groove of the door
frame (3).
C. Bend the panel gently so that the free side of the
panel can be slipped into the corresponding groove
of the door frame (4). Slide the panel down into the
groove of the bottom frame (5).
D. Between the upper edge of the panel and the door
frame there is a gap which should be covered by the
decoration strip.
E. Put the decoration strip across the door so that the
gap is covered and push it upward (6). The tabs on
the inside of the strip should fit behind the flange of
the door frame. Secure the decoration strip with the
two screws removed in Step A (1).
PANEL DIMENSIONS
MAX. THICKNESS 5/32" (4 mm)
REFR.MODELS
TYPE
RM 2620
upper
mm
inch
lower
mm
inch
RM 2820
upper
mm
inch
lower
mm
inch
HEIGHT
MAX.
MIN.
2
1
1
4
3
WIDTH
MAX.
MIN.
306
12-3/64
819
32-1/4
304
11-31/32
817
32-5/32
515
20-9/32
515
20-9/32
513
20-13/64
513
20-13/64
378
14-7/8
897
35-5/16
376
14-51/64
895
35-15/64
563
22-11/64
563
22-11/64
561
22-3/32
561
22-3/32
5
6
1
14
1
CERTIFIED VENT SYSTEM KITS
Refr.
Model
Kit
No.
Components
Drawing
RM 2620
RM 2820
4A
Roof Vent
3103633.xxx* Base
3103634.xxx* Cap
(Both Required)
Lower Side Vent
3102277.xxx*
* Fill in "xxx" with color code numbers. For color codes, contact your supplier
For further information, contact your dealer or distributor.
SPARE PARTS
The following list is a list of commonly used parts which
should be available, if required, from your Dometic
Service Center.
A = RM 2620
B = RM 2820
Part No.
200 74 19-19/1
200 74 19-21/7
293 06 97-02/0
293 03 79-00/9
200 75 90-05/8
200 75 90-06/6
293 11 32-01/9
17 37 54-19/3
17 37 42-18/0
293 18 26-01/6
293 14 18-03/8
200 05 71-25/3
200 17 32-18/5
200 27 26-06/1
200 27 26-16/0
293 21 06-01/2
293 16 00-02/3
Description
A
A
A
A
A
A
A
A
A
A
A
A
B
B
B
B
B
B
B
B
B
B
B
B
Jet, No. 53
Jet, No. 58
Burner
Electrode
Baffle
Baffle
Spark ignition device
Heater, 295W, 120V
Heater, 325W, 120V
Thermocouple
Door shelf, (freezer)
Door shelf, 4 pieces
Door shelf, 4 pieces
Box vegetable-, 2 pieces
Box vegetable-, 2 pieces
Lamp cover
Handle, cpl.
Contact an authorized service center for
parts and repairs as needed.
15
MO-FO 9951
16