Eclipse LED
Hyperion LED
ASSEMBLY INSTRUCTIONS
Eclipse LED - Hyperion LED
QUALIFIED
STAFF
OFF
IP=>
NO
LAMPS
Connection and maintenance
ofthe luminaire must be carried
out by trained and qualifiedstaff
only, in compliance with the
regulation in force.
Make sure there is no power
connected to the fitting before
carrying out any maintenance
The protection rating of the
electrical connection must be
equal to or greater than the IP
rating of the luminaire
Keep away from aggressive
agents and chemical
substances (e.g. fertilizer,
weed-killer, lime).
In case of break of the glass/
diffuser use original spare parts
only.
It is mandatory to install the power
supply in a suitable electrical
enclosure.
All luminaires have to undergo regular maintenance according to the
following steps:
- Check the fastening of the screws.
- Inspect cables and cable glands for any possible damage.
- Check the fastening of cable glands.
- Check if seals are in working order.
- Defect or damaged components must be replaced before switching the luminaire on. Use
original spare parts only.
It is important to carry out luminaire maintenance at each bulb substitution or at least once
per year.
Any improper use or installation, any tampering or any unauthorised modification of the
luminaire causes the immediate expiry of the warranty on the luminaire and of any claim
against the manufacturer.
Should Designplan Lighting allow the return of a luminaire for technical inspection or tests,
they must be returned with a piece of wiring cable (10-20cm connected to the luminaire).
79 Trenton Ave
Frenchtown, NJ 08825
Tel: 908-996-7710
Fax: 908-996-7042
Eclipse LED - Hyperion LED
IP65
U542004
COOL WHITE 6000K MID-POWER LEDs 7.5W/24Vdc
Remote electronic power supply to be ordered
U542005
NATURAL WHITE 4000K MID-POWER LEDs 7.5W/24Vdc
Remote electronic power supply to be ordered
U542006
WARM WHITE 3000K MID-POWER LEDs 7.5W/24Vdc
Remote electronic power supply to be ordered
ECLIPSE LED
For safety to be assured, the fitting has to be instal-led
and used properly, in compliance with local regulations
and Directives on electrical and electronic equi-pments
and with the mounting instructions included in the present
box: please keep this instruction data sheet for future
reference.
Dust-tight and protected against waterjets IP65
Suitable for installation on normally flammable surfaces
At the end of its usefull lifespan, the product must be disposed of separataly from ordinary
household wastes. The user is responsible for delivering the appliance to an appropriate
collection facility at the end of its useful lifespan. Appropriate separate collection to permit
recycling, treatment and environmentally compatible disposal helps prevent negative impact
on the environ-ment and human health and promotes recycling of the materials making
up the product. For more informantion on available collection facilities, contact your local
waste collection service.
U527011
COOL WHITE 6000K MID-POWER LEDs 7.5W/24Vdc
Remote electronic power supply to be ordered
U527012
NATURAL WHITE 4000K MID-POWER LEDs 7.5W/24Vdc
Remote electronic power supply to be ordered
U547013
WARM WHITE 3000K MID-POWER LEDs 7.5W/24Vdc
Remote electronic power supply to be ordered
79 Trenton Ave
Frenchtown, NJ 08825
HYPERION LED
Tel: 908-996-7710
Fax: 908-996-7042
Eclipse LED
INSTALLATION ON WALL
WIRING
*
24Vdc
LOW VOLTAGE
--- --- --- ---
24Vdc
LOW VOLTAGE
--- --- --- ---
FIX THE METAL PLATE BY RESPECTING THE “OK” POSITION
(2 HOLES FOR FIXING BOLTS AND 1 FOR CABLE WHICH HAS
TO BE UNDER THE PLATE)
!
*
7.09"
K
K
CLA
K
CLA
OK
OK
CLA
K
CLA
OK
OK
79 Trenton Ave
Frenchtown, NJ 08825
STEP 4
NO
STEP 3
NO
STEP 2
NO
STEP 1
NO
Tel: 908-996-7710
Fax: 908-996-7042
Eclipse LED - Hyperion LED
USE ONLY WITH CLASS II POWER UNIT
DRIVER
The individual lamps must be connected in parallel. Only power up the system once all the lamps have being connected.
79 Trenton Ave
Frenchtown, NJ 08825
Tel: 908-996-7710
Fax: 908-996-7042
MiniMartina
Hyperion
- Martina
LED
INSTALLATION ON WALL
WIRING
STEP 1
CLAK
CLAK
CLAK
STEP 2
CLAK
STEP 3
24Vdc
LOW VOLTAGE
--- --- --- --160
230
180
STEP 4
24Vdc
LOW VOLTAGE
--- --- --- ---
STEP 5
SATIN PLATE FIXING (OPTIONAL) CODE 160
1
*
1
!
2
*CLEAN THE FIXING SURFACE WITH ALCOHOL OR SOLVENT BEFORE GLUING THE PLATE
79 Trenton Ave
Frenchtown, NJ 08825
Tel: 908-996-7710
Fax: 908-996-7042