8 September 2016
ADDENDUM #1
(Total of 56 pages)
Additions and Renovations to
Andrews Heights Elementary
Kanawha County Schools
BID #17-104
The following items are clarifications and/or changes to the scope of the work and shall be included in the
contract price.
Item #1
Supplementary Instructions to Bidders for AIA Document A701-1997
A.
Item #2
General
A.
Item #3
Item #5
Note that the school day for students is Monday – Friday from 7:40 am to 2:10 pm.
Specification Section 01210 - Allowances
A.
Item #4
Delete Paragraph 9.1 “Prevailing Wage Rates” as these are no longer applicable to the
project. Delete any further references where it may occur within these specifications.
Note, however, that certified payrolls as described herein are still required and must be
submitted to the Owner with each pay request.
As clarification, Electrical contractor to provide all necessary rough-ins and installation
for security items as called for in Allowance No. 3 for Base Bid and in Alternate No. 2 Administrative Area Modifications and Renovations.
Specification Section 04810 – Unit Masonry Assemblies
A.
Refer to Article 1.4 and delete paragraph B in its entirety.
B.
Refer to Article 1.4.C and delete subparagraph 4 in its entirety.
Specification Section 05120 – Structural Steel Framing
A.
Refer to Article 1.7 and delete Paragraph B in its entirety. Revise Paragraph A to read:
“Fabricator Qualifications: A firm experienced in producing metal fabrication similar to
those indicated for this project and with a record of successful in-service performance,
as well as sufficient production capacity to produce required units.
300 Summers Street, Suite 1200, Charleston, WV 25301-1630
(Phone) 304/342-2151 • 304/342-2197 (Fax)
Item #6
Specification Section 07531 – EPDM Membrane Roofing
A.
Item #7
Specification Section 08433 – Folding Glass Storefronts
A.
Item #8
Subject to compliance with requirements of the contract documents, add SUNFLEX of
Naples, Florida (800-606-0756) as an acceptable manufacturer.
Specification Section 08710 – Door Hardware
A.
Item #9
Subject to compliance with requirements of the contract documents, add Versico as an
acceptable manufacturer.
At Hardware Sets #16 and #18, delete “4642” for Surface Automatic Operator and
substitute “By Access Control Supplier”.
This device will be provided under
Specification Section 01210 – Allowances. Installation is in this contract under
Alternate No. 2.
Specification Section 09511 – Acoustical Panel Ceilings
A.
Subject to compliance with requirements of the contract documents, add the following
as acceptable manufacturers and products:
1.
2.
3.
4.
5.
6.
Item #10
Specification Section 09910 – Painting
A.
Item #11
Food Service Equipment to be included under Alternate No. 8. Hood at dishwasher is
included in Base Bid. Refer to Part 4 – Schedule of Equipment and delete in its
entirety. See attached Revised Part 4 – Schedule of Equipment for description of
items.
Specification Section 12355 – Laminated Plastic Casework and Countertops
A.
9/8/16
Refer to the attached section.
Specification Section 11400 – Food Service Equipment
A.
Item #13
Base bid includes installation of sprinkler system throughout existing building and new
addition. All exposed sprinkler lines and fittings are to be painted as part of base bid.
Specification Section 10350 – Flagpoles
A.
Item #12
Under Article 2.2 – Ceiling Type “A”, add Rockfon Artic #600
Under Article 2.3 – Ceiling Type “C”, add Rockfon Medical Standard #33200
Under Article 2.4 – Ceiling Type “D-1”, add Rockfon Graph Grid #8901.44
Under Article 2.4 – Ceiling Type “D-2”, add Rockfon Graph Grid #8903.44
Under Article 2.6 – for all ceiling types, add Rockfon Chicago Metallic 1200
Under Article 2.8 – Metal Edge Moldings and Trim, add Rockfon Infinity
Under plastic laminate faced manufacturer casework, add Southern Cabinetry in
Bidwell, Ohio and Chandler’s Plywood Products in Huntington, West Virginia as
acceptable manufacturers, subject to compliance with requirements of the contract
documents.
Addendum #1 – KCS – Andrews Heights
Page 2 of 5
Item #14
Specification Section 15732 – Packaged, Outdoor, Central-Station Air-Handling Units
A.
Item #15
Specification Section 16716 – Communication Backbone Cabling
A.
Item #16
Item #18
A.
Data cabling is by contractor. Contractor is responsible for installation, termination and
testing. The intent is to reuse the existing data rack and patch panels. Data cabling
shall be plenum rated.
B.
Electrical contractor to include as part of their bid for base bid and respective alternates
all data and telephone cabling from device to point of termination in data closets. Data
equipment, such as hubs, switches and racks, to be provided by Owner.
Specification Section 16718 – Conductors and Cables for Electronic Safety and
Security
9/8/16
Refer to the attached new specification.
Specification Section 16789 – Integrated and Cables for Electronic Safety and Security.
A.
Item #20
Refer to the attached new specification.
Clarification:
A.
Item #19
Refer to the attached new specification.
Specification Section 16717 – Communication Horizontal Cabling
A.
Item #17
Refer to article 2.1.A, Manufacturer’s and add the “Diakin” to list of approved
Manufacturer’s.
Refer to the attached new specification.
Drawing C1.1 – Site Plan
Drawing A1.1 – Overall Floor Plan
A.
Delete list of alternates shown on both drawings. Refer to Specification Section 01230
– Alternates for a complete list of alternates and accompanying description.
B.
Refer to concrete paving at service and note the concrete paving profile at this location
shall be comprised of 6” aggregate base, and 6” concrete with 6x6xW4.0xW4.0 WWF.
Revise detail “Dumpster Pad & Apron C2106” on Sheet C2.1 to reflect this profile and
note this detail applies to the concrete paving at the service area located to the west of
the new multipurpose room addition. Concrete to be 4,500 psi air entrained w/ broom
finish. Provide tool control joints at 8’-0” c/c max and expansion joints at 24’-0” c/c
max. At expansion joints, provide #4 x 12” smooth steel dowel with 4” greased dowel
cap on one end spaced at 2’-0” c/c.
C.
Refer to new asphalt drive to the east of the multipurpose room addition and add a 6”
concrete curb to connect the concrete sidewalk to the south of the addition to the
concrete sidewalk to the north of the addition. Provide a lawn area between the
addition and the back of the curb.
Addendum #1 – KCS – Andrews Heights
Page 3 of 5
Item #21
Item #22
Drawing C2.1 – Site Details
A.
Refer to Detail “Asphalt Paving – Heavy Duty @ Drives” and note the profile shall be
comprised on 8” aggregate base, 4” asphalt base course, and 2” asphalt wearing
course.
B.
Refer to Detail “Asphalt Paving – Standard Duty @ Parking” and note the profile shall
be comprised on 6” aggregate base, 4” asphalt base course, and 1-1/2” asphalt
wearing course.
C.
Refer to concrete walk details and note a tooled control joint is to be provided 5’-0” c/c
max with an expansion joint located every 20’-0” c/c max.
Drawing A0.1 – Abbreviations, Symbols & General Notes
A.
Item #23
Item #24
Item #25
Item #26
9/8/16
Refer to symbol list and delete references to Sheets A0.5, A0.6 and A0.7.
Drawing A0.4 – Door Schedule, Door Details & Notes
A.
Refer to Door Schedule, Door 041 and note the door material is wood.
B.
Refer to Door Schedule and note Doors listed under Alternate #1 and Alternate #2, the
door material is wood.
Drawing A2.1 – Floor Plan Part A
A.
Refer to Studio A-112A and revise interior elevation marked on the plan south wall to
read 6120.
B.
Refer to Studio B-112E and revise interior elevation marked on the plan north wall to
read 6120.
C.
Refer to Teachers 112K and provide a 4’-0” wide sink base cabinet on the east wall.
Cabinet to be constructed for the adjacent casework.
D.
Refer to raised platform in the reading performance area and note the platform to be
constructed similar to Detail 1/A5.1.
Drawing A2.2 – Floor Plan Part B
Drawing A2.3 – Enlarged Floor Plan
A.
Washer, dryer and lockers indicated in Staff Room 014 are not in contract and will be
provided by Owner. Only rough-ins for washer and dryer are to be included in this
contract.
B.
On Drawing A2.3, change Refrigerator that is next to the hand sink from Item #25 to
Item #18.
Drawing A6.1 – Interior Elevations
A.
Refer to Elevation 6113 and note that the tackboard is to be 6’-0” wide x 5’-0” high.
B.
Refer to Elevations 6116 and 6117 and note that the visual display board assembly is
5’-0” high and the markerboard is 4’-0” high.
Addendum #1 – KCS – Andrews Heights
Page 4 of 5
C.
Item #27
Drawing A6.2 – Interior Elevations
A.
Item #28
Item #30
Refer to Plan Notes; omit Plan Note “W”.
Drawing E2.2 – Power Plan Part B
A.
See attached Sketch AD1.1 for circuiting of ADA door operators.
B.
Refer to Plan Notes; add Plan Note “L”; Existing RTU circuit relocated to panel “M”.
Intercept existing conduits and extend as required.
C.
Refer to Classrooms 102, 104 and 105; omit Plan Note “W” and replace with Plan
Note “L”.
Drawing E3.1 – Systems Plan Part A
A.
Item #31
Refer to Elevations 6201 and 6202 and note that the glazed window located over the
pair of doors is to be aluminum storefront windows.
Drawing E2.1 – Power Plan Part A
A.
Item #29
Refer to Elevation 6101 and note that the sink base is to be plastic laminate casework
with plastic laminate countertop.
Refer to Office 024; at symbol “IC”, add Plan Note “D”.
Drawing E3.2 – Systems Plan Part B
A.
Refer to Plan Notes; omit Plan Note “M” and replace with, Relocated Visitors
Center Control Panel.
B.
See Sketch AD1.1 included with this addendum for additional access control
devices.
Attachments:
Sketch AD1-1 – Systems Plan – Part “B” (1 page)
Section 10350 – Flagpoles (4 pages)
Section 11400 – Food Service Equipment, Part 4 – Schedule of Equipment (11 pages)
Section 16716 – Communications Backbone Cabling (8 pages)
Section 16717 – Communications Horizontal Cabling (8 pages)
Section 16718 – Conductors and Cables for Electronic Safety and Security (11 pages)
Section 16789 – Integrated Security / Building Management System (8 pages)
9/8/16
Addendum #1 – KCS – Andrews Heights
Page 5 of 5
KCS – ANDREWS HEIGHTS ADDITIONS AND RENOVATIONS
9/8/16
SECTION 10350 - FLAGPOLES
PART 1 - GENERAL
1.1
RELATED DOCUMENTS
A.
1.2
Drawings and general provisions of the Contract, including General and Supplementary
Conditions and Division 1 Specification Sections, apply to this Section.
SUMMARY
A.
Section includes ground-mounted flagpoles made from aluminum.
B.
Owner-Furnished Material: Flags.
C.
Related Sections: See Division 16 for site lighting fixtures.
1.3
PERFORMANCE REQUIREMENTS
A.
Structural Performance: Flagpole assemblies, including anchorages and supports, shall
withstand the effects of gravity loads, and the following loads and stresses within limits and
under conditions indicated according to the following design criteria:
1.
2.
3.
1.4
Seismic Loads: According to SEI/ASCE 7.
Wind Loads: According to NAAMM FP 1001, "Guide Specifications for Design of Metal
Flagpoles."
Base flagpole design on polyester flags of maximum standard size suitable for use with
flagpole or flag size indicated, whichever is more stringent.
ACTION SUBMITTALS
A.
Product Data: For each type of product indicated. Include construction details, material
descriptions, dimensions of individual components and profiles, operating characteristics,
fittings, accessories, and finishes for flagpoles.
B.
Shop Drawings: For flagpoles. Include plans, elevations, details and attachments to other
work. Show general arrangement, jointing, fittings, accessories, grounding, anchoring and
support.
1.
Include section and details of foundation system for ground-mounted flagpoles.
C.
Samples for Verification: For each type of exposed finish required, in manufacturer's standard
sizes.
D.
Delegated-Design Submittal: For flagpole assemblies indicated to comply with performance
requirements and design criteria, including analysis data signed and sealed by the qualified
professional engineer responsible for their preparation.
1.
1.5
Include loads, point reactions, and locations for attachment of flagpoles to building's
structure.
INFORMATIONAL SUBMITTALS
A.
Qualification Data: For qualified professional engineer.
FLAGPOLES
10350 - 1
KCS – ANDREWS HEIGHTS ADDITIONS AND RENOVATIONS
1.6
9/8/16
CLOSEOUT SUBMITTALS
A.
1.7
Operation and Maintenance Data:
manuals.
For flagpoles to include in operation and maintenance
QUALITY ASSURANCE
A.
1.8
Source Limitations: Obtain flagpole as complete unit, including fittings, accessories, bases, and
anchorage devices, from single source from single manufacturer.
DELIVERY, STORAGE, AND HANDLING
A.
General: Spiral wrap flagpoles with heavy paper and enclose in a hard fiber tube or other
protective container.
PART 2 - PRODUCTS
2.1
MANUFACTURERS
A.
Manufacturers:
following:
1.
2.
3.
4.
5.
6.
2.2
Subject to compliance with requirements, provide products by one of the
American Flagpole; a Kearney-National Inc. company.
Baartol Company.
Concord Industries, Inc.
Ewing Flagpoles.
Lingo Inc.; Acme Flagpole Company Division.
U.S. Flag & Flagpole Supply, LP.
FLAGPOLES
A.
Flagpole Construction, General: Construct flagpoles in one piece if possible. If more than one
piece is necessary, comply with the following:
1.
2.
3.
Fabricate shop and field joints without using fasteners, screw collars, or lead calking.
Provide flush hairline joints using self-aligning, snug-fitting, internal sleeves.
Provide self-aligning, snug-fitting joints.
B.
Exposed Height: 40’.
C.
Aluminum Flagpoles: Provide cone tapered flagpoles fabricated from seamless extruded tubing
complying with ASTM B 241/B 241M, Alloy 6063, with a minimum wall thickness of 3/16”.
D.
Metal Foundation Tube: Manufacturer's standard corrugated-steel foundation tube, not less
than 0.064” nominal wall thickness. Provide with 3/16” steel bottom plate and support plate;
3/4" diameter, steel ground spike; and steel centering wedges welded together. Galvanize steel
after assembly. Provide loose hardwood wedges at top of foundation tube for plumbing pole.
1.
2.
E.
Provide flashing collar of same material and finish as flagpole.
Provide steel ground protectors extending 12” aboveground and 6” belowground for steel
flagpoles where flashing collars are not provided.
Sleeve for Aluminum Flagpole:
concrete foundation.
1.
FLAGPOLES
Foundation sleeve, made to fit flagpole, for casting into
Provide flashing collar of same material and finish as flagpole.
10350 - 2
KCS – ANDREWS HEIGHTS ADDITIONS AND RENOVATIONS
F.
Cast-Metal Shoe Base: For anchor-bolt mounting; provide with anchor bolts.
1.
2.
2.3
9/8/16
Provide units made from aluminum with same finish as flag pole.
Provide ground spike at grade-mounted flagpoles.
FITTINGS
A.
Finial Ball: Manufacturer's standard flush-seam ball, sized as indicated or, if not indicated, to
match flagpole-butt diameter.
1.
B.
External Halyard: Ball-bearing, nonfouling, revolving truck assembly of cast metal with
continuous 5/16” diameter, braided polypropylene halyard and 9” cast-metal cleats with
fasteners. Finish exposed metal surfaces to match flagpole.
1.
2.4
0.063” spun aluminum with gold anodic finish.
Provide one halyard and one cleat at each flagpole, and with neoprene or vinyl covers.
MISCELLANEOUS MATERIALS
A.
Nonshrink, Nonmetallic Grout: Factory-packaged, nonstaining, noncorrosive, nongaseous grout
complying with ASTM C 1107.
B.
Drainage Material: Crushed stone, or crushed or uncrushed gravel; coarse aggregate.
C.
Sand: ASTM C 33, fine aggregate.
D.
Elastomeric Joint Sealant: Multicomponent nonsag urethane joint sealant complying with
requirements in Section 07920 "Joint Sealants" for Use NT (nontraffic) and for Use M, G, A,
and, as applicable to joint substrates indicated, for Use O.
E.
Bituminous Paint: Cold-applied asphalt emulsion complying with ASTM D 1187.
2.5
GENERAL FINISH REQUIREMENTS
A.
Comply with NAAMM's "Metal Finishes Manual for Architectural and Metal Products" for
recommendations for applying and designating finishes.
B.
Appearance of Finished Work: Noticeable variations in same piece are not acceptable.
Variations in appearance of adjoining components are acceptable if they are within the range of
approved Samples and are assembled or installed to minimize contrast.
2.6
ALUMINUM FINISHES
A.
Natural Satin Finish: AA-M32, fine, directional, medium satin polish; buff complying with AAM20; seal aluminum surfaces with clear, hard-coat wax.
B.
Clear Anodic Finish: AAMA 611, or thicker.
C.
Gold Anodic Finish: AAMA 611, AA-M32C22A43 Class I, 0.018 mm or thicker; gold color.
2.7
STEEL FINISHES
A.
Flagpole Interior Finish: Apply one coat of bituminous paint on interior of flagpole or otherwise
treat to prevent corrosion.
FLAGPOLES
10350 - 3
KCS – ANDREWS HEIGHTS ADDITIONS AND RENOVATIONS
B.
9/8/16
Galvanized Finish: Hot-dip galvanize after fabrication to comply with ASTM A 123/A 123M.
PART 3 - EXECUTION
3.1
EXAMINATION
A.
Examine substrates, areas, and conditions, with Installer present, for compliance with
requirements for installation tolerances, including foundation; accurate placement, pattern,
orientation of anchor bolts, and other conditions affecting performance of the Work.
B.
Proceed with installation only after unsatisfactory conditions have been corrected.
3.2
PREPARATION
A.
Prepare uncoated metal flagpoles that are set in foundation tubes by painting below-grade
portions with a heavy coat of bituminous paint.
B.
Foundation Excavation: Excavate to neat clean lines in undisturbed soil. Remove loose soil
and foreign matter from excavation and moisten earth before placing concrete. Place and
compact drainage material at excavation bottom.
C.
Provide forms where required due to unstable soil conditions and for perimeter of flagpole base
at grade. Secure and brace forms to prevent displacement during concreting.
D.
Place concrete, as specified in Section 03300 "Cast-in-Place Concrete." Compact concrete in
place by using vibrators. Moist-cure exposed concrete for not less than seven days or use
nonstaining curing compound.
E.
Trowel exposed concrete surfaces to a smooth, dense finish, free of trowel marks, and uniform
in texture and appearance. Provide positive slope for water runoff to perimeter of concrete
base.
3.3
FLAGPOLE INSTALLATION
A.
General: Install flagpoles where shown and according to Shop Drawings and manufacturer's
written instructions.
B.
Ground Set: Place sleeve, center and brace to prevent displacement during concreting. Place
concrete. Plumb and level sleeve and allow concrete to cure. Install flagpole, plumb, in sleeve.
C.
Baseplate: Cast anchor bolts in concrete foundation. Install baseplate on washers placed over
leveling nuts on anchor bolts and adjust until flagpole is plumb. After flagpole is plumb, tighten
retaining nuts and fill space under baseplate solidly with nonshrink, nonmetallic grout. Finish
exposed grout surfaces smooth and slope 45 degrees away from edges of baseplate.
D.
Mounting Brackets and Bases: Anchor brackets and bases securely through to structural
support with fasteners as indicated on Shop Drawings.
END OF SECTION 10350
FLAGPOLES
10350 - 4
KCS – ANDREWS HEIGHTS ADDITIONS AND RENOVATIONS
9/8/16
PART 4 - SCHEDULE OF EQUIPMENT (SEE DRAWING A2.3 – ENLARGED FLOOR PLANS)
ITEM 1
SOILED DISH TABLE
(1 REQ'D)
Titan Stainless Model CUSTOM
Soiled Dishtable shall be size and shape as per plan including pass-thru window sill. Unit
shall be constructed with 300 series 14 gauge stainless steel top with top to have a 10"
backsplash at rear and right end with a 45 degree turn back at top. Top shall be sloped to
dishwasher. Unit to set on 1 5/8" dia. stainless steel "H" legs furnished completed with
stainless steel bullet feet. Stainless Steel tubular under- shelf on both soiled and clean
table, (1) 20" X 20" X 8" pre-rinse sink with rack slide and strainer and (1) disposer
control bracket. Pass-thru shall be integral with the top and backsplash. Table to be
undercoated with approved sound-deadening material.
ITEM 2
HOSE REEL ASSEMBLY
(1 REQ'D)
Fisher Model 2985
Hose Reel Assembly, wall mount, stainless steel covered reel rinse with spray valve, 30
feet of 3/8" ID, 3 ply, 2 braid hose, pressure of 200 PSI, 1/2" NPT female inlet
1 ea
ITEM 3
Model 28231 Reel Rinse Installation Kit, wall-mounted
DISPOSER
(1 REQ'D)
Salvajor Model 300-SA-3-MRSS-LD
Disposer, Sink Assembly, 3-1/2" sink collar, 3 Hp motor, start/stop push button manual
reversing with safety line disconnect MRSS-LD control, includes fixed nozzle, vacuum
breaker, solenoid valve, sink stopper & flow control, heat treated aluminum alloy housing,
single support leg, UL, CSA, CE
1 ea
ITEM 4
208v/60hz/3-ph, 8.8 amps
DISHWASHER, CONVEYOR TYPE
(1 REQ'D)
Hobart Model CL44E-2
Dimensions: 68.5(h) x 44.75(w) x 31.25(d)
R/L 15KW Tank Heat 208/60/3 30KW Booster Conveyor Dishwasher, single tank, 202
racks/hour, insulated hinged doors, .62 gallon/rack, stainless steel enclosure panels,
Microprocessor controls with Low Temperature & Dirty Water Indicators, ENERGY
STAR®
1 ea
1 ea
1 ea
2 ea
3 ea
3 ea
2 ea
1 ea
1 ea
Standard warranty - 1-Year parts, labor & travel time during normal working
hours within the USA
Model DWTCLE Drain water tempering kit for CLE models
Self-installed
Model VNTHD/E-DOM E-series vent hood domestic
Model DISHRAK-PEG20 Peg rack
Model DISHRAK-COM20 Combination rack
Model BUNPAN-RACK Rack, bun pan
Model CLE/TBL-SWITCH Table LMT switch CLE-Series
Model CL44E-FETSTD Standard feet
FOOD SERVICE EQUIPMENT
11400 - 1
KCS – ANDREWS HEIGHTS ADDITIONS AND RENOVATIONS
ITEM 5
CLEAN DISH TABLE
9/8/16
(1 REQ'D)
Titan Stainless Model CUSTOM
Unit shall be size and shape as per plan. Unit shall be constructed with 300 series 14
gauge stainless steel top, top has a 10" backsplash at rear with a 45 degree turn back at
top, unit Top shall be sloped to dish washer. Unit to set on 1 5/8" dia. stainless steel "H"
legs furnished completed with stainless steel bullet feet. Stainless Steel tubular UnderShelf total length of table. Any necessary field modifications to be made at the time of
the installation. This includes any field welding requirements.
ITEM 6
EPOXY SHELVES
(8 REQ'D)
Focus Foodservice Model FF2460G
Dimensions: 60(w) x 24(d)
Shelf, Wire, 24"W x 60"L, green epoxy coated finish
8 ea
2 set
ITEM 7
Model FGN074G Post, 74"H, mobile, green epoxy coated with SaniGard™
Model FTPRCST5 Caster Set, 5" dia., thermoplastic rubber (TPR), with bumpers,
two swivel & two swivel with brake, 300lbs. capacity per caster, NSF (set of 4)
THREE (3) COMPARTMENT SINK
(1 REQ'D)
John Boos Model 3PB2028-2D24
Dimensions: 111.25(w) x 33.5(d)
Pro-Bowl Bakery Sink, (3) 20"W x 28" front-to-back x 12" deep compartments, (2) 24"
drain boards, 10"H boxed backsplash with 45° top & 2" return, (2) sets faucet holes,
16/300 stainless steel, 1-5/8" OD stainless steel legs with 1-1/4" OD adjustable side &
front bracing, fully welded front apron & adjustable stainless steel feet, NSF
3 ea
3 ea
2 ea
1 ea
2 ea
ITEM 9
Model PB-LWS-1 Straight Handle Lever Waste, for 3-1/2" industry standard sink
opening, standard valve, basket strainer (includes adapter for either 2" or 1-1/2'
drain outlet)
Model PB-LWB Lever waste support arm bracket
T&S Brass Model B-0230-CC Sink Mixing Faucet, 18" swing nozzle, wall
mounted, 8" centers on sink faucet with 1/2" IPS CC male inlets, lever handles
Model BHS1296-14/304 Shelf, wall mount, 12" W x 96" L, 14/304 stainless steel,
Stallion safety edge front, 1-1/2" turned up backsplash, NSF, KD
T&S Brass Model B-0230-K Installation Kit, (2) 1/2" NPT nipples, lock nuts and
washers, (2) short "Ell" 1/2" NPT female x male
WORK TABLE WITH WALL SHELF
(1 REQ'D)
John Boos Model ST4R5-3096SSK
Dimensions: 35.75(h) x 96(w) x 30(d)
Work Table, 96"W x 30"D, 14/300 stainless steel top with 5" backsplash, Stallion safety
edge front, 90° turndown on sides, 18 gauge stainless steel adjustable undershelf,
stainless steel legs & bullet feet, NSF, KD
1 ea
1 set
1 ea
Model D11 Drawer Unit, 3-tier, 19-1/2"W x 24"D x 21"H, for work top tables, NSF
Located on left side of the table
Model CAS02-R Casters, 5", heavy duty, locking, for 1-5/8" diameter legs, set of
6 (tables 84" & longer with 6 legs)
Model BHS1296PR14/304 Shelf, wall mount, 12" W x 96" L, 14/304 stainless
steel, with stainless steel pot rack bar & 1 stainless steel hook per foot, Stallion
safety edge front, 1-1/2" turned up backsplash, NSF, KD
FOOD SERVICE EQUIPMENT
11400 - 2
KCS – ANDREWS HEIGHTS ADDITIONS AND RENOVATIONS
ITEM 10
CART, UTILITY
9/8/16
(2 REQ'D)
Lakeside Manufacturing Model 422
Dimensions: 32(h) x 31(w) x 19(d)
Utility Cart, open, (3) shelf, shelf size 27"W x 18"D, stainless steel angle frame with push
handle, 500 lb. capacity
2 ea
ITEM 11
Casters, 4" swivel, std.
HEATED HOLDING CABINET
(2 REQ'D)
Alto-Shaam Model 1200-UP
Dimensions: 75.81(h) x 26.44(w) x 32.19(d)
Halo Heat® Holding Cabinet, double compartment, on/off simple control with adjustable
thermostats, indicator light, (2) sets of chrome plated universal side rails, (4) sets of pan
slides, (16) 20" x 12" x 2-1/2" full size pan capacity, heavy duty 20 gauge stainless steel
exterior, 5" casters; 2 rigid, 2 swivel with brakes, EcoSmart®, cULus, UL-EPH, ANSI/NSF
4, CE, IP X4, TUV NORD, EAC
2 ea
2 ea
4 ea
ITEM 12
120v/60/1-ph, 16.0 amps, 1.9kW, 9' cord, NEMA 5-20P
Solid door, hinged on right, standard
Pass-thru design
HD RANGE, 36", 6 OPEN BURNERS
(1 REQ'D)
Garland/US Range Model C0836-6
Dimensions: 42(h) x 36(w) x 39.38(d)
Cuisine Series Heavy Duty Range, gas, 36", (6) 30,000 BTU open burners, cabinet base,
6" backguard, stainless steel front & sides, 6" adjustable legs, 180,000 BTU (U S Range)
1 ea
1 ea
1 ea
1 ea
1 ea
1 ea
ITEM 13
Two year limited parts and labor warranty, covers products purchased and
installed in the USA only, standard
Gas type to be specified
Model 2670200 Natural Gas Regulator, 3/4" N.P.T. (Consult spec sheet and
specify)
3/4" Rear gas connection, including end cap & cover (Consult spec sheet and
specify)
Swivel Casters, polyurethane wheels (non-marking)
Dormont Model 1675KIT48 Dormont Blue Hose™ Moveable Gas Connector Kit,
3/4" inside dia., 48" long, covered with stainless steel braid, coated with blue
antimicrobial PVC, 1 SnapFast® QD, 1 full port valve (2) 90° elbows, coiled
restraining cable with hardware, 180,000 BTU/hr minimum flow capacity, limited
lifetime warranty
TILTING KETTLE
(1 REQ'D)
Cleveland Range Model KGL25T
Kettle, gas, tilting, 25-gallon capacity, 2/3 steam jacket design, floor mounted control
console supports, stainless steel exterior finish, standard with flanged feet, 50 psi rating,
electronic spark ignition, cover & draw-off optional
FOOD SERVICE EQUIPMENT
11400 - 3
KCS – ANDREWS HEIGHTS ADDITIONS AND RENOVATIONS
1 ea
1 ea
1 ea
1 ea
1 ea
1 ea
1 ea
1 ea
ITEM 15
9/8/16
1-year limited warranty, standard
Natural Gas
120v/60/1-ph, 5.0 amp, electronic spark ignition, cord & plug for controls,
standard
Model TD2 2" tangent draw-off valve with strainer
Model CHS25 Spring-assisted cover (25 gallon)
Model DPKT Double Pantry Faucet, with swing spout & mounting bracket for
tilting kettles
Model PCK Pan Carrier, for all floor model kettles 25 gal & larger except KDM25-T
Dormont Model 1675KIT48 Dormont Blue Hose™ Moveable Gas Connector Kit,
3/4" inside dia., 48" long, covered with stainless steel braid, coated with blue
antimicrobial PVC, 1 SnapFast® QD, 1 full port valve (2) 90° elbows, coiled
restraining cable with hardware, 180,000 BTU/hr minimum flow capacity, limited
lifetime warranty
BOILERLESS CONVECTION STEAMER
(1 REQ'D)
AccuTemp Model N61201E060
Dimensions: 30(h) x 24(w) x 28(d)
(QUICK SHIP) Connected Evolution™ Boilerless, Convection Steamer featuring Steam
Vector Technology, flush mount countertop, natural gas, holds (6) 12"x 20"x 2-1/2" deep
pans, Digital Controls, water and drain connection required, warranty NOT voided by
water quality, NO water filtration required, 60,000BTU, 120/60/1ph, 5' cord & NEMA 515P, ENERGY STAR®
1 ea
1 ea
1 ea
1 ea
1 ea
1 ea
ITEM 16
1 year parts & labor warranty, standard
(K-12) 1 year extended warranty.
Lifetime service and support guarantee
Door hinged on right standard
Model SNH-11-00 Support Stand, for single Steam'N'Hold™ or Evolution units,
standard mounting height: 34-7/8" to bottom, stainless steel, with 5" casters
Dormont Model 1650KIT48 STEAMER Dormont Blue Hose™ Moveable Gas
Connector Kit, 1/2" inside dia., 48" long, covered with stainless steel braid,
coated with blue antimicrobial PVC, 1 SnapFast® QD, 1 full port valve (2) 90°
elbows, coiled restraining cable with hardware, 68,000 BTU/hr minimum flow
capacity, limited lifetime warranty
COMBI OVEN
(2 REQ'D)
Rational Model A629206.19E202
Dimensions: 29.75(h) x 42(w) x 38.25(d)
(CMP 62NG) CombiMaster® Plus, Combi Oven/Steamer, natural gas, (6) 18" x 26" full
size sheet or (12) 12" x 20" full size hotel pan capacity, mode selector control, 100
cooking programs, LED display, 5-speed programmable fan, core temperature probe,
hand shower with automatic retracting system, interface USB,(3) grid shelves, hinging
rack 2-5/8", 208v/60/1-ph, 8’cord, NEMA 6-15P, 106,000 BTU (dual voltage: retrofitable
to 240v/60/1-ph, 106,000 BTU)
2 ea
2 ea
2 years parts and labor warranty
Model 8720.1560US Installation Kit, for gas SCC WE/CM P 101G (120/60/1ph);
gas SCC WE/CM P 62G (208-240/60/1ph); gas SCC WE/CM P 61G
(120/60/1ph)
FOOD SERVICE EQUIPMENT
11400 - 4
KCS – ANDREWS HEIGHTS ADDITIONS AND RENOVATIONS
2 ea
1 ea
2 ea
6 ea
10 ea
2 ea
ITEM 17
9/8/16
Model CAP Chef Assistance Program, a RATIONAL certified Chef conducts 4
hours/location specialized application training with personnel
Model 60.71.933 Combi-Duo Stacking Kit, Mobile, casters, for electric or gas
SCC WE 62 or CM P 62 stacked on electric SCC WE 62, SCC WE 102, CM P
62, or CM P 102
Door hinged on right std.
Model 6010.2101 Gastronorm Grid Shelf, 2/1 size, 24" x 20", stainless steel
Model 6019.1250 CombiFry Basket, 1/2 GN, 12" x 10"
Model 6019.1150 CombiFry Basket, 1/1 GN, 12" x 20"
UNIVERSAL PAN RACK
(2 REQ'D)
Channel Manufacturing Model UTR-12
Dimensions: 70(h) x 20.5(w) x 26(d)
Utility Universal Rack, 70"H, (12) pan capacity, 5" spacing, 3-1/4" universal angles for
12"x20" thru 18"x26" steam table & bun pans, aluminum construction, 5" swivel casters,
NSF
ITEM 18
REACH-IN REFRIGERATOR
(1 REQ'D)
Traulsen Model RHT232NUT-FHS
Dimensions: 83.25(h) x 52.13(w) x 35(d)
Spec-Line Refrigerator, Reach-in, two-section, 46.0 cu. ft., self-contained refrigeration,
stainless steel exterior and interior, standard depth, narrow full-height door or doors with
Santoprene® EZ-Clean Gaskets, (3) adjustable wire shelves per section, INTELATRAUL™ microprocessor controls, 6" adjustable stainless steel legs, 5/8 HP, cULus,
NSF
1 ea
1 ea
1 ea
4 ea
1 set
ITEM 19
115v/60/1ph, 8.2 amps, with cord & NEMA 5-15P, standard
3 year service/labor, 5 year compressor warranty, standard
Left door hinged left/right hinged right, standard
Additional plated shelf
Casters, 6" high (set of 4)
PREP TABLE
(1 REQ'D)
John Boos Model ST4R5-36120SBK
Dimensions: 35.75(h) x 120(w) x 36(d)
Work Table, 120"W x 36"D, 14/300 stainless steel top with 5" backsplash & turndown,
Stallion safety edge front, 90° turndown on sides, stainless steel legs, side & rear
adjustable bracing, NSF, KD
1 ea
2 ea
1 ea
1 ea
Model 0002J1 2" deep 5"H rear riser, with turndown & "Z" clips, in lieu of
standard 1-1/2" deep 5"H rear riser
Model CUT1618124 Weld-In Under mount Sink, one compartment, 16"W x 18"L
x 12"D, 14/300 stainless steel fabricated bowl, includes cutout, bowl, faucet holes
& welding/polishing (Not available for FBLG & UFBLG)
Model PBF-8-SLF Sink Mixing Faucet, with 8" swing nozzle, wall mounted, 8"
centers, with 1/2" NPT
Model 0002J1 2" deep 5"H rear riser, with turndown & "Z" clips, in lieu of
standard 1-1/2" deep 5"H rear riser
FOOD SERVICE EQUIPMENT
11400 - 5
KCS – ANDREWS HEIGHTS ADDITIONS AND RENOVATIONS
1 kit
1 ea
1 ea
1 ea
ITEM 20
9/8/16
Model PB-DMMK-90 Splash Mount Faucet Mounting Kit, includes (2) 1/2" supply
nipples, (2) retainer nuts, (2) lock washers, (2) rubber washers and (2) male &
female short 90° elbows
Model PB-LWS-1 Straight Handle Lever Waste, for 3-1/2" industry standard sink
opening, standard valve, basket strainer (includes adapter for either 2" or 1-1/2'
drain outlet)
Model PB-LWB Lever waste support arm bracket
Model D11 Drawer Unit, 3-tier, 19-1/2"W x 24"D x 21"H, for work top tables, NSF
Located on left side of table
DISPOSER
(1 REQ'D)
Salvajor Model 200-SA-3-MRSS
Disposer, Sink Assembly, 3-1/2" sink collar, 2 Hp motor, start/stop push button manual
reversing MRSS control, includes fixed nozzle, vacuum breaker, solenoid valve, sink
stopper & flow control, heat treated aluminum alloy housing, UL, CSA, CE
1 ea
1 ea
ITEM 21
208v/60hz/1-ph, 12.1 amps
Model LSA8 Disposer support leg, for 3/4 HP - 2 HP disposers
FOOD PROCESSOR
(1 REQ'D)
Hobart Model FP100-1B
Dimensions: 19.5(h) x 8.81(w) x 16.69(d)
Food Processor, angled continuous feed design, half-size hopper, 11 lb per/min
production cap., 420 rpm, stainless steel cutting surfaces, planetary gear transmission,
triple safety interlocks, aluminum housing, rubber feet, includes plate package PLATE6PACK, 120/60/1, 1/3 HP, UL, NSF
1 ea
ITEM 22
Standard warranty - 1-Year parts, labor & travel time during normal working
hours within the USA
MEAT SLICER
(1 REQ'D)
Hobart Model HS7-1
Dimensions: 27.25(h) x 24.63(w) x 30.31(d)
Heavy Duty Meat Slicer, automatic, 13" CleanCut™ removable knife with removal tool,
burnished finish, (3) stroke lengths, & (4) stroke speeds, removable meat grip assembly,
removable ring guard cover, single action top mounted sharpener with Borazon™ stones,
manual lift lever, 1/2 hp motor, 5.6amps, 120v/60hz/1-ph, NSF cETLus
1 ea
ITEM 25
Standard warranty - 1-Year parts, labor & travel time during normal working
hours within the USA
HAND SINKS
HAND SINKS BY OTHERS
FOOD SERVICE EQUIPMENT
11400 - 6
KCS – ANDREWS HEIGHTS ADDITIONS AND RENOVATIONS
ITEM 26
WORK TABLE WITH SHELF
9/8/16
(1 REQ'D)
John Boos Model ST4R5-3048SSK
Dimensions: 35.75(h) x 48(w) x 30(d)
Work Table, 48"W x 30"D, 14/300 stainless steel top with 5" backsplash, Stallion safety
edge front, 90° turndown on sides, 18 gauge stainless steel adjustable undershelf,
stainless steel legs & bullet feet, NSF, KD
1 ea
1 set
1 ea
ITEM 28
Model DR2015-S30 Drawer, for 30"D work tables, 15"W x 20"D x 5"deep,
stainless steel front & drawer pan, roller bearing slides, NSF, for stainless steel
table tops only
Model CAS01-R Casters, 5", heavy duty, locking, for 1-5/8" Diameter legs (set of
4)
Model BHS1248PR14/304 Shelf, wall mount, 12" W x 48" L, 14/304 stainless
steel, with stainless steel pot rack bar & 1 stainless steel hook per foot, Stallion
safety edge front, 1-1/2" turned up backsplash, NSF, KD
PLANETARY MIXER/STAND
(1 REQ'D)
Hobart Model HL200-1STD
100-120/50/60/1; Bench type mixer; with bowl, beater, & whip; US/EXP configuration
Legacy Planetary Mixer, Bench, 20-quart, (3) fixed speeds plus stir speed, gear-driven
transmission, 15-minute SmartTimer™, #12 taper hub, manual bowl lift, stainless steel
bowl, aluminum "B" beater, stainless steel "D" wire whip, stainless steel bowl guard, 1/2
hp, cord with plug
1 ea
ITEM 29
Standard warranty - 1-Year parts, labor & travel time during normal working
hours within the USA
1 ea
Model TABLEHW-HL2012 Mixer Table; 27”W x 32”D x 26”T, the top shelf is
drilled for mounting an HL120 or HL200 mixer, includes 4 posts for storing
attachments, a lower shelf for additional storage, and (4) locking 5” diameter
wheels
EQUIPMENT STAND
(1 REQ'D)
John Boos Model MS4-3030SSK
Dimensions: 20(h) x 30(w) x 30(d)
Machine Stand, heavy duty, 30"W x 30"D x 20"H, 14/300 stainless steel top with marine
edge, stainless steel adjustable lower shelf, stainless legs & bullet feet, KD
1 set
ITEM 30
Model CAS01-R-X Casters, 5", heavy duty, locking, for 1-5/8"Diameter legs (legs
will not be modified for height) (set of 4)
INGREDIENT BIN
(3 REQ'D)
Cambro Model IBSF27148
Dimensions: 28.75(h) x 13(w) x 30.5(d)
Flat Top Ingredient Bin, mobile, 27 gallon capacity, 1-pc seamless polyethylene bin, 2-pc
sliding polycarbonate lid, S-hook on front (scoop NOT included), (4) 3" heavy duty
casters (2 front swivel, 2 fixed), white with clear cover, NSF
FOOD SERVICE EQUIPMENT
11400 - 7
KCS – ANDREWS HEIGHTS ADDITIONS AND RENOVATIONS
ITEM 31
PREP TABLE WITH SHELF
9/8/16
(1 REQ'D)
John Boos Model ST4R5-3696SBK
Dimensions: 35.75(h) x 96(w) x 36(d)
Work Table, 96"W x 36"D, 14/300 stainless steel top with 5" backsplash & turndown,
Stallion safety edge front, 90° turndown on sides, stainless steel legs, side & rear
adjustable bracing, NSF, KD
1 ea
1 ea
1 kit
1 ea
1 ea
1 ea
ITEM 32
Model CUT1618124 Weld-In under mount Sink, one compartment, 16"W x 18"L x
12"D, 14/300 stainless steel fabricated bowl, includes cutout, bowl, faucet holes
& welding/polishing
Model PBF-8HD-8-SLF Sink Mixing Faucet, with 8" swing spout, deck mounted,
8" centers, with 1/2" NPT
Model PB-DMMK Deck Mount Faucet Mounting Kit, includes (2) 1/2" supply
nipples, (2) retainer nuts, (2) lock washers and (2) rubber washers
Model PB-LWS-1 Straight Handle Lever Waste, for 3-1/2" industry standard sink
opening, standard valve, basket strainer (includes adapter for either 2" or 1-1/2'
drain outlet)
Model PB-LWB Lever waste support arm bracket
Model BHS1296PR14/304 Shelf, wall mount, 12" W x 96" L, 14/304 stainless
steel, with stainless steel pot rack bar & 1 stainless steel hook per foot, Stallion
safety edge front, 1-1/2" turned up backsplash, NSF, KD
PLANETARY MIXER
(1 REQ'D)
Hobart Model HL600-1STD
200-240/50/60/3/1 Mixer; with bowl, beater, “D” whip, & spiral dough arm; US/EXP
configuration. Legacy Planetary Mixer, 2.7 HP, 60-quart, (4) fixed speeds, gear-driven
transmission, 50-Minute SmartTimer™, #12 attach hub, power bowl lift, stainless steel
bowl, stainless steel bowl guard, "B" beater, "D" wire whip, "ED" dough hook
1 ea
1 ea
ITEM 34
Standard warranty: 1-Year parts, labor, and travel time during normal working
hours within the USA
Model TRUCK-HL1486 Bowl Truck, for use with 60, 80 & 140 quart Legacy
Mixers
ICE CUBER WITH BIN
(1 REQ'D)
Ice-O-Matic Model ICEU220HA
Dimensions: 39(h) x 24.54(w) x 26.27(d)
ICE Series™ Cube Ice Maker, cube-style, Undercounter, air-cooled, self-contained
condenser, approximately 238 lb/108 kg production/24 hours, 70 lb. built-in bin, half-size
cube, 115v/60/1-ph, 11.9 amps, ENERGY STAR®
1 ea
1 ea
1 ea
1 ea
3 yr. parts & labor warranty, standard
5 yr. evaporator warranty, standard
5 yr. parts on the compressor warranty, standard
Model IFQ1 Water Filter Manifold, single filter, 6"W x 4"D x 15"H, for ice makers
producing up to 1,000 lbs. (454.4 Kg.) of ice per day, 1.5 gpm maximum flow
rate, pressure 125 max psi, IsoNet scale inhibitor, .5 micron particle reduction,
NSF
FOOD SERVICE EQUIPMENT
11400 - 8
KCS – ANDREWS HEIGHTS ADDITIONS AND RENOVATIONS
ITEM 36
MILK COOLER
9/8/16
(1 REQ'D)
Traulsen Model RMC58S4
Dimensions: 46(h) x 58(w) x 32.13(d)
Dealer's Choice Forced-Air Single Access Milk Cooler, sliding door, holds (16) 13"x13"
crates or (10) 13"x19" milk crates, stainless steel interior and exterior, reinforced floor,
sliding caster rails , (4) heavy-duty stainless steel dunnage racks, top-mount refrigeration
system, Santoprene® E-Z clean gaskets, floor drain, 4" casters, 1/3 hp, UL, NSF.
1 ea
1 ea
ITEM 37
3 year service/labor, 5 year compressor warranty, standard
115v/60/1ph, 7.2 amps, NEMA 5-15P
HOT FOOD SERVING COUNTER
(1 REQ'D)
Delfield Model SH5-NU
Dimensions: 36(h) x 60(w) x 30(d)
Shelleysteel™ Hot Food Serving Counter, Electric, 4-pan capacity, 14-gauge stainless
steel top, 18-gauge stainless steel exterior, 14-gauge galvanized bottom, enclosed base
with no under storage, 5" swivel casters
1 ea
1 ea
1 ea
1 ea
1 ea
1 ea
ITEM 38
30" height
120/208-230v/60/1-ph, 22.0 amps, 4000/4800watts, NEMA 14-30P, standard
(1) year parts & (90) day labor warranty, standard
Model F Line-Up Interlock Device
Glass front counter protector
E5 Work Shelf 10” Fold Down, Stainless Steel
TRAY RACK DISPENSER
(1 REQ'D)
Delfield Model TT2-1014
Dimensions: 37.75(h) x 21.25(w) x 26.75(d)
Dispenser, Tray, open frame mobile design, dual self-elevating tray platforms, for 11" x
15" trays, 4" casters, NSF
1 ea
ITEM 39
1 year parts & 90 day labor warranty, standard
UTILITY SERVING COUNTER
(1 REQ'D)
Delfield Model SC-74
Dimensions: 36(h) x 74(w) x 30(d)
Shelleysteel™ Solid Top Serving Counter, 74" long, 14 gauge stainless steel counter top,
storage unit, 5" swivel casters, NSF
1 ea
1 ea
1 ea
1 ea
1 year parts & 90 day labor warranty, standard
Model SG11 Modify Standard Height, modify height of unit to height 30"
Model F Line-Up Interlock Device
30” height
FOOD SERVICE EQUIPMENT
11400 - 9
KCS – ANDREWS HEIGHTS ADDITIONS AND RENOVATIONS
ITEM 40
COLD PAN SERVING COUNTER
9/8/16
(1 REQ'D)
Delfield Model SCSC-60-B
Dimensions: 36(h) x 60(w) x 30(d)
Shelleysteel™ Cold Food Serving Counter, 52" x 21.62" x 7" deep Bloomington style cold
pan, drain with valve, reinforced stainless steel enclosed base, 5" casters, self-contained
refrigeration, R404A, 1/4 hp, cUL, UL, NSF
1 ea
1 ea
1 ea
1 ea
1 ea
1 ea
1 ea
ITEM 42
30" height
115v/60/1-ph, 7.0 amps, NEMA 5-15P, standard
1 year parts & 90 day labor warranty, standard
Model F Line-Up Interlock Device
Model E-60 Work Shelf, 10" fold-down, stainless steel
Model KS-60 Sneeze Guard, single service, flip-up
Model L-60 Incandescent light fixture
COOLER/FREEZER
(1 REQ'D)
AmeriKooler 12’ 11 ¼” X 18’ 9 7/8” X 8’7”
4” thick AKXPS4 extruded foam with Rvalues of R29 for coolers and R32 for freezers
with a 50 Year Thermal Warranty. UL Classified Core Flame Spread 15, Smoke Rating
less than 165.
15 Year Panel Warranty and 1 Year Parts Warranty
Interior walls: 26 Ga. Stucco Embossed Acrylume; Exterior walls: 26 Ga. Stucco
Embossed Acrylume; Interior ceiling: 26 Ga. Stucco Embossed Acrylume; Exterior
ceiling: 26 Ga. Stucco Embossed Acrylume
Type 2K
Application: Hand Trucks, Dunnage Racks, Beer Kegs, Log Carts, Dollie Carts
NSF Floor panel rated for 1250 LBS/ SQ. FT.
22 Ga. Textured Stainless Steel Integral. Reinforced with coated 0.5" plywood
underlay
(2) Standard 36" x 76" hinged flush door with brushed hardware. Interior & Exterior finish:
26 Ga. Stucco Embossed Acrylume. 36" kickplates to interior and exterior of door. Energy
saving temperature regulating thermostat heater wire and heated relief vent. Heavy duty
deadbolt handle latch. Digital LED Thermometer with pilot light switch. Vapor Proof light
& globe.155v output. 2.2 amps.
(4) 48" LED LIGHT STRIP FIXTURE 96 LUMENS /WATT 120VAC, 0.33 AMPS TEMP
RANGE: 30°F104°F,
(1) Bohn 3 1/2 HP Condensing Unit Model BZT035L6B 208230/60/1 Low Temperature,
Scroll,
Air-cooled, R404A (13,420 BTU @ 10°F room temperature and 95°F ambient)
(1) Bohn LET120BEWMC6K, 208230/60/1, low
Profile electric defrost evaporator, 1.5 Amps with EC motor, Includes Mounted TXV,
LLSV & Thermostat
(1) Extended 4 year compressor Warranty
(1) 1 HP Bohn Outdoor Condensing Unit, Model BHT010X6BFM, 208230/60/1, MCA 15
Amps, BTUH 8850, Medium Temperature, Hermetic, Air-cooled, R404A, 1 year
compressor and parts warranty from date of shipment within Continental USA.
(1) Bohn ADT090AEWMC6K, 115/60/1, low profile air defrost evaporator, 1.8 Amps with
FOOD SERVICE EQUIPMENT
11400 - 10
KCS – ANDREWS HEIGHTS ADDITIONS AND RENOVATIONS
9/8/16
EC motor,
Includes Mounted TXV, LLSV & Thermostat
(1) Extended 4 year compressor Warranty
Approved equal: Kolpak and Imperial Brown
ITEM 43
COOLER/FREEZER SHELVING
(4 REQ'D)
Focus Foodservice Model FF2436G
Dimensions: 36(w) x 24(d)
Shelf, Wire, 24"W x 36"L, green epoxy coated finish
48 ea
32 ea
8 ea
4 ea
ITEM 44
Model FG074G Post, 74"H, stationary, green epoxy coated with SaniGard™
FFG2448G green epoxy coated finish
FF2442 green epoxy coated finish
FF2454G green epoxy coated finish
CAN RACK
(1 REQ'D)
Channel Manufacturing Model CSR-156M
Dimensions: 88(h) x 42.25(w) x 28.25(d)
First In, First Out Can Rack, 82"H, mobile, inclined angle can slides, front loading, holds
(156) #10 cans, front edge turned up, welded aluminum construction, 5" x 2" heavy duty
casters (2) swivel (2) rigid, NSF
1 set
ITEM 45
Model /5B Caster Brakes, heavy duty (for two casters)
DRY STORAGE SHELVING
(15 REQ'D)
Focus Foodservice Model FF2448G
Dimensions: 48(w) x 24(d)
Shelf, Wire, 24"W x 48"L, green epoxy coated finish
15 ea Model FF2460G Shelf, Wire, 24"W x 60"L, green epoxy coated finish
24 ea Model FGN086G Post, 86"H, mobile, green epoxy coated with SaniGard™
6 sets Model FTPRCST5 Caster Set, 5" dia., thermoplastic rubber (TPR), with bumpers,
two swivel & two swivel with brake, 300lbs. capacity per caster, NSF (set of 4)
NOTE:
All equipment is to be bid as specified. If Bidder desires to substitute another
manufacturer in lieu of item specified, he must request approval within ten (10) days prior
to bid date. Requests need to be submitted to Architect complete with information of
manufacturer's name, model number, etc. If approved, Architect will issue addendum to
all Bidders of record
END OF SECTION 11400
FOOD SERVICE EQUIPMENT
11400 - 11
KCS – ANDREWS HEIGHTS ADDITION AND RENOVATIONS
9/8/16
SECTION 16716 - COMMUNICATIONS BACKBONE CABLING
PART 1 - GENERAL
1.1
SUMMARY
A.
Section Includes:
1.
2.
3.
4.
B.
Related Sections:
1.
1.2
Pathways.
UTP cable.
Cable connecting hardware, patch panels, and cross-connects.
Cabling identification products.
Division 16 Section "Conductors and Cables for Electronic Safety and Security" for voice
and data cabling associated with system panels and devices.
BACKBONE CABLING DESCRIPTION
A.
Backbone cabling system shall provide interconnections between communications equipment
rooms, main terminal space, and entrance facilities in the telecommunications cabling system
structure. Cabling system consists of backbone cables, intermediate and main cross-connects,
mechanical terminations, and patch cords or jumpers used for backbone-to-backbone crossconnection.
B.
Backbone cabling cross-connects may be located in communications equipment rooms or at
entrance facilities. Bridged taps and splitters shall not be used as part of backbone cabling.
1.3
PERFORMANCE REQUIREMENTS
A.
1.4
General Performance: Backbone cabling system shall comply with transmission standards in
TIA/EIA-568-B.1, when tested according to test procedures of this standard.
SUBMITTALS
A.
Product Data: For each type of product indicated.
B.
Shop Drawings:
1.
2.
3.
4.
5.
C.
System Labeling Schedules: Electronic copy of labeling schedules, in software and
format selected by Owner.
Cabling administration drawings and printouts.
Wiring diagrams to show typical wiring schematics including the following:
a.
Cross-connects.
b.
Patch panels.
c.
Patch cords.
Cross-connects and patch panels. Detail mounting assemblies, and show elevations and
physical relationship between the installed components.
Cable tray layout, showing cable tray route to scale, with relationship between the tray
and adjacent structural, electrical, and mechanical elements.
Qualification Data: For Installer, qualified layout technician, installation supervisor, and field
inspector.
COMMUNICATIONS BACKBONE CABLING
16716 - 1
KCS – ANDREWS HEIGHTS ADDITION AND RENOVATIONS
D.
Source quality-control reports.
E.
Field quality-control reports.
F.
Maintenance data.
1.5
9/8/16
QUALITY ASSURANCE
A.
Installer Qualifications: Cabling Installer must have personnel certified by BICSI on staff.
B.
Surface-Burning Characteristics: As determined by testing identical products according to
ASTM E 84 by a qualified testing agency. Identify products with appropriate markings of
applicable testing agency.
1.
2.
Flame-Spread Index: 25 or less.
Smoke-Developed Index: 50 or less.
C.
Electrical Components, Devices, and Accessories: Listed and labeled as defined in NFPA 70,
by a qualified testing agency, and marked for intended location and application.
D.
Telecommunications Pathways and Spaces: Comply with TIA/EIA-569-A.
E.
Grounding: Comply with ANSI-J-STD-607-A.
1.6
DELIVERY, STORAGE, AND HANDLING
A.
Test cables upon receipt at Project site. Test each pair of UTP cable for open and short
circuits.
PART 2 - PRODUCTS
2.1
PATHWAYS
A.
Cable Support: NRTL labeled for support of Category 6 cabling, designed to prevent
degradation of cable performance and pinch points that could damage cable.
1.
2.
3.
B.
Conduit and Boxes: Comply with requirements in Division 16 Section "Raceways and Boxes."
1.
2.2
Support brackets with cable tie slots for fastening cable ties to brackets.
Lacing bars, spools, J-hooks, and D-rings.
Straps and other devices.
Outlet boxes shall be no smaller than 2” wide, 3” high, and 2-1/2” deep.
BACKBOARDS
A.
2.3
Backboards: Plywood, 3/4” x 48” x 96”. Comply with requirements in Division 6 Section "Rough
Carpentry" for plywood backing panels.
UTP CABLE
A.
Manufacturers:
following:
Subject to compliance with requirements, provide products by one of the
COMMUNICATIONS BACKBONE CABLING
16716 - 2
KCS – ANDREWS HEIGHTS ADDITION AND RENOVATIONS
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
B.
Belden CDT Inc.; Electronics Division.
Berk-Tek; a Nexans company.
CommScope, Inc.
Draka USA.
Genesis Cable Products; Honeywell International, Inc.
KRONE Incorporated.
Mohawk; a division of Belden CDT.
Nordex/CDT; a subsidiary of Cable Design Technologies.
Superior Essex Inc.
SYSTIMAX Solutions; a CommScope Inc. brand.
3M.
Tyco Electronics/AMP Netconnect; Tyco International Ltd.
Description: 100-ohm, 100 pair UTP, formed into 25-pair binder groups covered with
a thermoplastic jacket.
1.
2.
3.
4.
2.4
9/8/16
Comply with ICEA S-90-661 for mechanical properties.
Comply with TIA/EIA-568-B.1 for performance specifications.
Comply with TIA/EIA-568-B.2, Category 5e.
Listed and labeled by an NRTL acceptable to authorities having jurisdiction as complying
with UL 444 and NFPA 70 for the following types:
a.
Communications, Plenum Rated: Type CMP or MPP, complying with NFPA 262.
b.
Communications, Riser Rated: Type CMR or MPR, complying with UL 1666.
c.
Communications, Limited Purpose: Type CMX or CMP.
d.
Multipurpose, Plenum Rated: Type MPP, complying with NFPA 262.
e.
Multipurpose, Riser Rated: Type MPR, complying with UL 1666.
UTP CABLE HARDWARE
A.
Manufacturers:
following:
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
Subject to compliance with requirements, provide products by one of the
American Technology Systems Industries, Inc.
Dynacom Corporation.
Hubbell Premise Wiring.
KRONE Incorporated.
Leviton Voice & Data Division.
Molex Premise Networks; a division of Molex, Inc.
Nordex/CDT; a subsidiary of Cable Design Technologies.
Panduit Corp.
Siemon Co. (The).
Tyco Electronics/AMP Netconnect; Tyco International Ltd.
B.
General Requirements for Cable Connecting Hardware: Comply with TIA/EIA-568-B.2, IDC
type, with modules designed for punch-down caps or tools. Cables shall be terminated with
connecting hardware of same category or higher.
C.
Connecting Blocks: 110-style IDC for Category 5e. Provide blocks for the number of cables
terminated on the block, plus 25% spare. Integral with connector bodies, including plugs and
jacks where indicated.
D.
Cross-Connect: Modular array of connecting blocks arranged to terminate building cables and
permit interconnection between cables.
1.
Number of Terminals per Field: One for each conductor in assigned cables.
COMMUNICATIONS BACKBONE CABLING
16716 - 3
KCS – ANDREWS HEIGHTS ADDITION AND RENOVATIONS
E.
9/8/16
Patch Panel: Modular panels housing multiple-numbered jack units with IDC-type connectors at
each jack for permanent termination of pair groups of installed cables.
1.
Number of Jacks per Field: One for each four-pair UTP cable indicated.
F.
Jacks and Jack Assemblies: Modular, color-coded, eight-position modular receptacle units with
integral IDC-type terminals.
G.
Patch Cords: Factory-made, 4-pair cables in 48” lengths; terminated with 8-position modular
plug at each end.
1.
2.
2.5
Patch cords shall have bend-relief-compliant boots and color-coded icons to ensure
Category 6 performance. Patch cords shall have latch guards to protect against
snagging.
Patch cords shall have color-coded boots for circuit identification.
GROUNDING
A.
Comply with requirements in Division 16 Section "Grounding and Bonding" for grounding
conductors and connectors.
B.
Comply with ANSI-J-STD-607-A.
2.6
IDENTIFICATION PRODUCTS
A.
2.7
Comply with TIA/EIA-606-A and UL 969 for a system of labeling materials, including label
stocks, laminating adhesives, and inks used by label printers.
SOURCE QUALITY CONTROL
A.
Testing Agency: Engage a qualified testing agency to evaluate cables.
B.
Factory test cables on reels according to TIA/EIA-568-B.1.
C.
Factory test UTP cables according to TIA/EIA-568-B.2.
D.
Cable will be considered defective if it does not pass tests and inspections.
E.
Prepare test and inspection reports.
PART 3 - EXECUTION
3.1
ENTRANCE FACILITIES
A.
3.2
Coordinate backbone cabling with the protectors and demarcation point provided by
communications service provider.
WIRING METHODS
A.
Wiring Method: Install cables in raceways and cable trays except within consoles, cabinets,
desks, and counters and except in accessible ceiling spaces, in attics, and in gypsum board
partitions where unenclosed wiring method may be used. Conceal raceway and cables except
in unfinished spaces.
COMMUNICATIONS BACKBONE CABLING
16716 - 4
KCS – ANDREWS HEIGHTS ADDITION AND RENOVATIONS
1.
2.
9/8/16
Install plenum cable in environmental air spaces, including plenum ceilings.
Comply with requirements for raceways and boxes specified in Division 16 Section
"Raceways and Boxes."
B.
Wiring Method: Conceal conductors and cables in accessible ceilings, walls, and floors where
possible.
C.
Wiring within Enclosures: Bundle, lace, and train cables within enclosures. Connect to terminal
points with no excess and without exceeding manufacturer's limitations on bending radii.
Provide and use lacing bars and distribution spools.
3.3
INSTALLATION OF PATHWAYS
A.
Cable Trays: Comply with NEMA VE 2 and TIA/EIA-569-A.
B.
Comply with requirements for demarcation point, pathways, cabinets, and racks specified in
Division 16 Section "Communications Equipment Room Fittings." Drawings indicate general
arrangement of pathways and fittings.
C.
Comply with TIA/EIA-569-A for pull-box sizing and length of conduit and number of bends
between pull points.
D.
Comply with requirements in Division 16 Section "Raceways and Boxes" for installation of
conduits and wireways.
E.
Install manufactured conduit sweeps and long-radius elbows whenever possible.
F.
Pathway Installation in Communications Equipment Rooms:
1.
2.
3.
4.
5.
G.
3.4
Position conduit ends adjacent to a corner on backboard where a single piece of plywood
is installed, or in the corner of room where multiple sheets of plywood are installed
around perimeter walls of room.
Install cable trays to route cables if conduits cannot be located in these positions.
Secure conduits to backboard when entering room from overhead.
Extend conduits 3” above finished floor.
Install metal conduits with grounding bushings and connect with grounding conductor to
grounding system.
Backboards: Install backboards with 96” dimension vertical. Butt adjacent sheets tightly, and
form smooth gap-free corners and joints.
INSTALLATION OF CABLES
A.
Comply with NECA 1.
B.
General Requirements for Cabling:
1.
2.
3.
4.
5.
6.
Comply with TIA/EIA-568-B.1.
Comply with BICSI ITSIM, Ch. 6, "Cable Termination Practices."
Install 110-style IDC termination hardware unless otherwise indicated.
Terminate all conductors; no cable shall contain unterminated elements.
Make
terminations only at indicated outlets, terminals, cross-connects, and patch panels.
Cables may not be spliced. Secure and support cables at intervals not exceeding 30”
and not more than 6” from cabinets, boxes, fittings, outlets, racks, frames, and terminals.
Install lacing bars to restrain cables, to prevent straining connections, and to prevent
bending cables to smaller radii than minimums recommended by manufacturer.
COMMUNICATIONS BACKBONE CABLING
16716 - 5
KCS – ANDREWS HEIGHTS ADDITION AND RENOVATIONS
7.
8.
9.
10.
11.
C.
Comply with TIA/EIA-568-B.2.
Do not untwist UTP cables more than 1/2” from the point of termination to maintain cable
geometry.
Open-Cable Installation:
1.
2.
3.
E.
Bundle, lace, and train conductors to terminal points without exceeding manufacturer's
limitations on bending radii, but not less than radii specified in BICSI ITSIM, "Cabling
Termination Practices" Chapter. Use lacing bars and distribution spools.
Do not install bruised, kinked, scored, deformed, or abraded cable. Do not splice cable
between termination, tap, or junction points. Remove and discard cable if damaged
during installation and replace it with new cable.
Cold-Weather Installation: Bring cable to room temperature before dereeling. Heat
lamps shall not be used for heating.
In communications equipment room, install a 10’ long service loop on each end of cable.
Pulling Cable: Comply with BICSI ITSIM, Ch. 4, "Pulling Cable." Monitor cable pull
tensions.
UTP Cable Installation:
1.
2.
D.
9/8/16
Install cabling with horizontal and vertical cable guides in telecommunications spaces
with terminating hardware and interconnection equipment.
Suspend UTP cable not in a wireway or pathway, a minimum of 8” above ceilings by
cable supports not more than 60” apart.
Cable shall not be run through structural members or in contact with pipes, ducts, or
other potentially damaging items.
Installation of Cable Routed Exposed under Raised Floors:
1.
2.
3.
Install plenum-rated cable only.
Install cabling after the flooring system has been installed in raised floor areas.
Coil cable 6” long not less than 12” in diameter below each feed point.
F.
Group connecting hardware for cables into separate logical fields.
G.
Separation from EMI Sources:
1.
2.
3.
4.
Comply with BICSI TDMM and TIA/EIA-569-A recommendations for separating
unshielded copper voice and data communication cable from potential EMI sources,
including electrical power lines and equipment.
Separation between open communications cables or cables in nonmetallic raceways and
unshielded power conductors and electrical equipment shall be as follows:
a.
Electrical Equipment Rating Less Than 2 kVA: A minimum of 5”.
b.
Electrical Equipment Rating between 2 and 5 kVA: A minimum of 12”.
c.
Electrical Equipment Rating More Than 5 kVA: A minimum of 24”.
Separation between communications cables in grounded metallic raceways and
unshielded power lines or electrical equipment shall be as follows:
a.
Electrical Equipment Rating Less Than 2 kVA: A minimum of 2-1/2”.
b.
Electrical Equipment Rating between 2 and 5 kVA: A minimum of 6”.
c.
Electrical Equipment Rating More Than 5 kVA: A minimum of 12”.
Separation between communications cables in grounded metallic raceways and power
lines and electrical equipment located in grounded metallic conduits or enclosures shall
be as follows:
a.
Electrical Equipment Rating Less Than 2 kVA: No requirement.
b.
Electrical Equipment Rating between 2 and 5 kVA: A minimum of 3”.
c.
Electrical Equipment Rating More Than 5 kVA: A minimum of 6”.
COMMUNICATIONS BACKBONE CABLING
16716 - 6
KCS – ANDREWS HEIGHTS ADDITION AND RENOVATIONS
5.
6.
3.5
9/8/16
Separation between Communications Cables and Electrical Motors and Transformers, 5
kVA or HP and Larger: A minimum of 48”.
Separation between Communications Cables and Fluorescent Fixtures: Minimum of 5”.
FIRESTOPPING
A.
Comply with requirements in Division 7 Section "Through-Penetration Firestop Systems."
B.
Comply with TIA/EIA-569-A, Annex A, "Firestopping."
C.
Comply with BICSI TDMM, "Firestopping Systems" Article.
3.6
GROUNDING
A.
Install grounding according to BICSI TDMM, "Grounding, Bonding, and Electrical Protection"
Chapter.
B.
Comply with ANSI-J-STD-607-A.
C.
Locate grounding bus bar to minimize the length of bonding conductors. Fasten to wall allowing
at least 2” clearance behind the grounding bus bar. Connect grounding bus bar with a minimum
No. 4 AWG grounding electrode conductor from grounding bus bar to suitable electrical building
ground.
D.
Bond metallic equipment to the grounding bus bar, using not smaller than No. 6 AWG
equipment grounding conductor.
3.7
IDENTIFICATION
A.
Identify system components, wiring, and cabling complying with TIA/EIA-606-A. Comply with
requirements for identification specified in Division 16 Section "Electrical Identification."
1.
Color-code cross-connect fields and apply colors to voice and data service backboards,
connections, covers, and labels.
B.
Comply with requirements in Division 9 Section "Interior Painting" for painting backboards. For
fire-resistant plywood, do not paint over manufacturer's label.
C.
Paint and label colors for equipment identification shall comply with TIA/EIA-606-A for Class 2
level of administration Cable Schedule: Install in a prominent location in each equipment room
and wiring closet. List incoming and outgoing cables and their designations, origins, and
destinations. Protect with rigid frame and clear plastic cover. Furnish an electronic copy of final
comprehensive schedules for Project.
D.
Cabling Administration Drawings: Show building floor plans with cabling administration-point
labeling. Identify labeling convention and show labels for telecommunications closets,
backbone pathways and cables, terminal hardware and positions, horizontal cables, work areas
and workstation terminal positions, grounding buses and pathways, and equipment grounding
conductors.
E.
Cable and Wire Identification:
1.
Label each cable within 4” of each termination and tap, where it is accessible in a cabinet
or junction or outlet box, and elsewhere as indicated.
COMMUNICATIONS BACKBONE CABLING
16716 - 7
KCS – ANDREWS HEIGHTS ADDITION AND RENOVATIONS
2.
3.
4.
5.
F.
Each wire connected to building-mounted devices is not required to be numbered at
device if color of wire is consistent with associated wire connected and numbered within
panel or cabinet.
Exposed Cables and Cables in Cable Trays and Wire Troughs: Label each cable at
intervals not exceeding 15’.
Label each terminal strip and screw terminal in each cabinet, rack, or panel.
a.
Individually number wiring conductors connected to terminal strips and identify
each cable or wiring group being extended from a panel or cabinet to a buildingmounted device with name and number of particular device as shown.
b.
Label each unit and field within distribution racks and frames.
Identification within Connector Fields in Equipment Rooms and Wiring Closets: Label
each connector and each discrete unit of cable-terminating and connecting hardware.
Where similar jacks and plugs are used for both voice and data communication cabling,
use a different color for jacks and plugs of each service.
Labels shall be preprinted or computer-printed type with printing area and font color that
contrasts with cable jacket color but still complies with requirements in TIA/EIA 606-A, for the
following:
1.
3.8
9/8/16
Cables use flexible vinyl or polyester that flexes as cables are bent.
FIELD QUALITY CONTROL
A.
Tests and Inspections:
1.
2.
3.
Visually inspect UTP jacket materials for NRTL certification markings. Inspect cabling
terminations in communications equipment rooms for compliance with color-coding for
pin assignments, and inspect cabling connections for compliance with TIA/EIA-568-B.1.
Visually inspect cable placement, cable termination, grounding and bonding, equipment
and patch cords, and labeling of all components.
Test UTP copper cabling for DC loop resistance, shorts, opens, intermittent faults, and
polarity between conductors. Test operation of shorting bars in connection blocks. Test
cables after termination but not cross-connection.
a.
Test instruments shall meet or exceed applicable requirements in TIA/EIA-568-B.2.
Perform tests with a tester that complies with performance requirements in "Test
Instruments (Normative)" Annex, complying with measurement accuracy specified
in "Measurement Accuracy (Informative)" Annex. Use only test cords and
adapters that are qualified by test equipment manufacturer for channel or link test
configuration.
B.
Data for each measurement shall be documented. Data for submittals shall be printed in a
summary report that is formatted similar to Table 10.1 in BICSI TDMM, or transferred from the
instrument to the computer, saved as text files, and printed and submitted.
C.
Remove and replace cabling where test results indicate that they do not comply with specified
requirements.
D.
Prepare test and inspection reports.
END OF SECTION 16716
COMMUNICATIONS BACKBONE CABLING
16716 - 8
KCS ANDREWS HEIGHTS ADDITIONS AND RENOVATIONS
9/6/16
SECTION 16717 - COMMUNICATIONS HORIZONTAL CABLING
PART 1 - GENERAL
1.1
SUMMARY
A.
Section Includes:
1.
2.
3.
4.
5.
6.
B.
Related Sections:
1.
2.
1.2
UTP cabling.
Coaxial cable.
Multiuser telecommunications outlet assemblies.
Cable connecting hardware, patch panels, and cross-connects.
Telecommunications outlet/connectors.
Cabling system identification products.
Division 16 Section "Communications Backbone Cabling" for voice and data cabling
associated with system panels and devices.
Division 16 Section "Conductors and Cables for Electronic Safety and Security" for voice
and data cabling associated with system panels and devices.
DEFINITIONS
A.
BICSI: Building Industry Consulting Service International.
B.
Consolidation Point: A location for interconnection between horizontal cables extending from
building pathways and horizontal cables extending into furniture pathways.
C.
Cross-Connect: A facility enabling the termination of cable elements and their interconnection
or cross-connection.
D.
EMI: Electromagnetic interference.
E.
IDC: Insulation displacement connector.
F.
LAN: Local area network.
G.
MUTOA: Multiuser telecommunications outlet assembly, a grouping in one location of several
telecommunications outlet/connectors.
H.
Outlet/Connectors: A connecting device in the work area on which horizontal cable or outlet
cable terminates.
I.
RCDD: Registered Communications Distribution Designer.
J.
UTP: Unshielded twisted pair.
1.3
HORIZONTAL CABLING DESCRIPTION
A.
Horizontal cable and its connecting hardware provide the means of transporting signals
between the telecommunications outlet/connector and the horizontal cross-connect located in
the communications equipment room. This cabling and its connecting hardware are called
"permanent link," a term that is used in the testing protocols.
COMMUNICATIONS HORIZONTAL CABLING
16717 - 1
KCS ANDREWS HEIGHTS ADDITIONS AND RENOVATIONS
1.
2.
9/6/16
Horizontal cabling shall contain no more than one transition point or consolidation point
between the horizontal cross-connect and the telecommunications outlet/connector.
Bridged taps and splices shall not be installed in the horizontal cabling.
B.
A work area is approximately 100 sq. ft., and includes the components that extend from the
telecommunications outlet/connectors to the station equipment.
C.
The maximum allowable horizontal cable length is 295’. This maximum allowable length does
not include an allowance for the length of 16’ to the workstation equipment. The maximum
allowable length does not include an allowance for the length of 16’ in the horizontal crossconnect.
1.4
PERFORMANCE REQUIREMENTS
A.
1.5
General Performance: Horizontal cabling system shall comply with transmission standards in
TIA/EIA-568-B.1, when tested according to test procedures of this standard.
SUBMITTALS
A.
Product Data: For each type of product indicated.
1.
B.
For coaxial cable, include the following installation data for each type used:
a.
Nominal OD.
b.
Minimum bending radius.
c.
Maximum pulling tension.
Shop Drawings:
1.
2.
3.
System Labeling Schedules: Electronic copy of labeling schedules that are part of the
cabling and asset identification system of the software.
Cabling administration drawings and printouts.
Cross-connects and patch panels. Detail mounting assemblies, and show elevations and
physical relationship between the installed components.
C.
Source quality-control reports.
D.
Field quality-control reports.
E.
Maintenance Data: For splices and connectors to include in maintenance manuals.
1.6
QUALITY ASSURANCE
A.
Surface-Burning Characteristics: As determined by testing identical products according to
ASTM E 84 by a qualified testing agency. Identify products with appropriate markings of
applicable testing agency.
1.
2.
Flame-Spread Index: 25 or less.
Smoke-Developed Index: 50 or less.
B.
Electrical Components, Devices, and Accessories: Listed and labeled as defined in NFPA 70,
by a qualified testing agency, and marked for intended location and application.
C.
Telecommunications Pathways and Spaces: Comply with TIA/EIA-569-A.
D.
Grounding: Comply with ANSI-J-STD-607-A.
COMMUNICATIONS HORIZONTAL CABLING
16717 - 2
KCS ANDREWS HEIGHTS ADDITIONS AND RENOVATIONS
1.7
9/6/16
COORDINATION
A.
Coordinate layout and installation of telecommunications pathways and cabling with Owner's
telecommunications and LAN equipment and service suppliers.
B.
Coordinate telecommunications outlet/connector locations with location of power receptacles at
each work area.
1.8
EXTRA MATERIALS
A.
Furnish extra materials that match products installed and that are packaged with protective
covering for storage and identified with labels describing contents.
1.
2.
3.
4.
Patch-Panel Units: One of each type.
Connecting Blocks: One of each type.
Device Plates: One of each type.
Multiuser Telecommunications Outlet Assemblies: One of each type.
PART 2 - PRODUCTS
2.1
BACKBOARDS
A.
2.2
Backboards: Plywood, fire-retardant treated, 3/4” x 48” x 96”. Comply with requirements in
Division 6 Section "Rough Carpentry" for plywood backing panels.
UTP CABLE
A.
Description: 100-ohm, 4-pair UTP, formed into 25-pair, binder groups covered with a blue
thermoplastic jacket.
1.
2.
3.
4.
Comply with ICEA S-90-661 for mechanical properties.
Comply with TIA/EIA-568-B.1 for performance specifications.
Comply with TIA/EIA-568-B.2, Category 6.
Listed and labeled by an NRTL acceptable to authorities having jurisdiction as complying
with UL 444 and NFPA 70 for the following types:
a.
Multipurpose, Plenum Rated: Type MPP, complying with NFPA 262.
B.
General Requirements for Cable Connecting Hardware: Comply with TIA/EIA-568-B.2, IDC
type, with modules designed for punch-down caps or tools. Cables shall be terminated with
connecting hardware of same category or higher.
C.
Patch Panel: Modular panels housing multiple-numbered jack units with IDC-type connectors at
each jack for permanent termination of pair groups of installed cables.
2.3
COAXIAL CABLE
A.
Cable Characteristics: Broadband type, recommended by cable manufacturer specifically for
broadband data transmission applications. Coaxial cable and accessories shall have 75-ohm
nominal impedance with a return loss of 20 dB maximum from 7 to 806 MHz.
B.
NFPA and UL compliance, listed and labeled by an NRTL acceptable to authorities having
jurisdiction as complying with UL 1655 and with NFPA 70 "Radio and Television Equipment"
and "Community Antenna Television and Radio Distribution" Articles. Types are as follows:
1.
CATV Plenum Rated: Type CATVP, complying with NFPA 262.
COMMUNICATIONS HORIZONTAL CABLING
16717 - 3
KCS ANDREWS HEIGHTS ADDITIONS AND RENOVATIONS
2.4
9/6/16
COAXIAL CABLE HARDWARE
A.
2.5
Coaxial-Cable Connectors: Type BNC, 75 ohms.
TELECOMMUNICATIONS OUTLET/CONNECTORS
A.
Jacks: 100-ohm, balanced, twisted-pair connector; four-pair, eight-position modular. Comply
with TIA/EIA-568-B.1.
B.
Workstation Outlets: Two-port-connector assemblies mounted in single faceplate.
1.
2.
3.
2.6
Faceplate: stainless steel complying with Division 16 Section "Wiring Devices."
For use with snap-in jacks accommodating any combination of UTP, optical fiber, and
coaxial work area cords.
a.
Flush mounting jacks, positioning the cord at a 45° angle.
Legend: Machine printed, in the field, using adhesive-tape label.
GROUNDING
A.
Comply with requirements in Division 16 Section "Grounding and Bonding" for grounding
conductors and connectors.
B.
Comply with ANSI-J-STD-607-A.
2.7
IDENTIFICATION PRODUCTS
A.
Comply with TIA/EIA-606-A and UL 969 for labeling materials, including label stocks, laminating
adhesives, and inks used by label printers.
B.
Comply with requirements in Division 16 Section "Electrical Identification."
2.8
SOURCE QUALITY CONTROL
A.
Factory test UTP and optical fiber cables on reels according to TIA/EIA-568-B.1.
B.
Factory test UTP cables according to TIA/EIA-568-B.2.
C.
Factory-sweep test coaxial cables at frequencies from 5 MHz to 1 GHz. Sweep test shall test
the frequency response, or attenuation over frequency, of a cable by generating a voltage
whose frequency is varied through the specified frequency range and graphing the results.
D.
Cable will be considered defective if it does not pass tests and inspections.
E.
Prepare test and inspection reports.
PART 3 - EXECUTION
3.1
ENTRANCE FACILITIES
A.
Coordinate backbone cabling with the protectors and demarcation point provided by
communications service provider.
COMMUNICATIONS HORIZONTAL CABLING
16717 - 4
KCS ANDREWS HEIGHTS ADDITIONS AND RENOVATIONS
3.2
9/6/16
WIRING METHODS
A.
Wiring Method: Install cables in raceways except within consoles, cabinets, desks, and
counters and except in accessible ceiling spaces, in attics, and in gypsum board partitions
where unenclosed wiring method may be used. Conceal raceway and cables except in
unfinished spaces.
1.
Install plenum cable in environmental air spaces, including plenum ceilings.
B.
Wiring Method: Conceal conductors and cables in accessible ceilings, walls, and floors where
possible.
C.
Wiring within Enclosures: Bundle, lace, and train cables to terminal points with no excess and
without exceeding manufacturer's limitations on bending radii. Provide and use lacing bars and
distribution spools.
3.3
INSTALLATION OF CABLES
A.
Comply with NECA 1.
B.
General Requirements for Cabling:
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
C.
Comply with TIA/EIA-568-B.1.
Comply with BICSI ITSIM, Ch. 6, "Cable Termination Practices."
Install 110-style IDC termination hardware unless otherwise indicated.
MUTOA shall not be used as a cross-connect point.
Consolidation points may be used only for making a direct connection to
telecommunications outlet/connectors:
a.
Do not use consolidation point as a cross-connect point, as a patch connection, or
for direct connection to workstation equipment.
b.
Locate consolidation points for UTP at least 49’ from communications equipment
room.
Terminate conductors; no cable shall contain unterminated elements. Make terminations
only at indicated outlets, terminals, cross-connects, and patch panels.
Cables may not be spliced. Secure and support cables at intervals not exceeding 30”
and not more than 6” from cabinets, boxes, fittings, outlets, racks, frames, and terminals.
Install lacing bars to restrain cables, to prevent straining connections, and to prevent
bending cables to smaller radii than minimums recommended by manufacturer.
Bundle, lace, and train conductors to terminal points without exceeding manufacturer's
limitations on bending radii, but not less than radii specified in BICSI ITSIM, "Cabling
Termination Practices" Chapter. Install lacing bars and distribution spools.
Do not install bruised, kinked, scored, deformed, or abraded cable. Do not splice cable
between termination, tap, or junction points. Remove and discard cable if damaged
during installation and replace it with new cable.
Cold-Weather Installation: Bring cable to room temperature before dereeling. Heat
lamps shall not be used for heating.
In the communications equipment room, install a 10’ long service loop on each end of
cable.
Pulling Cable: Comply with BICSI ITSIM, Ch. 4, "Pulling Cable." Monitor cable pull
tensions.
UTP Cable Installation:
1.
2.
Comply with TIA/EIA-568-B.2.
Do not untwist UTP cables more than 1/2” from the point of termination to maintain cable
geometry.
COMMUNICATIONS HORIZONTAL CABLING
16717 - 5
KCS ANDREWS HEIGHTS ADDITIONS AND RENOVATIONS
D.
Group connecting hardware for cables into separate logical fields.
E.
Separation from EMI Sources:
1.
2.
3.
4.
5.
6.
3.4
9/6/16
Comply with BICSI TDMM and TIA/EIA-569-A for separating unshielded copper voice
and data communication cable from potential EMI sources, including electrical power
lines and equipment.
Separation between open communications cables or cables in nonmetallic raceways and
unshielded power conductors and electrical equipment shall be as follows:
a.
Electrical Equipment Rating Less Than 2 kVA: A minimum of 5”.
b.
Electrical Equipment Rating between 2 and 5 kVA: A minimum of 12”.
c.
Electrical Equipment Rating More Than 5 kVA: A minimum of 24”.
Separation between communications cables in grounded metallic raceways and
unshielded power lines or electrical equipment shall be as follows:
a.
Electrical Equipment Rating Less Than 2 kVA: A minimum of 2-1/2”.
b.
Electrical Equipment Rating between 2 and 5 kVA: A minimum of 6”.
c.
Electrical Equipment Rating More Than 5 kVA: A minimum of 12”.
Separation between communications cables in grounded metallic raceways and power
lines and electrical equipment located in grounded metallic conduits or enclosures shall
be as follows:
a.
Electrical Equipment Rating Less Than 2 kVA: No requirement.
b.
Electrical Equipment Rating between 2 and 5 kVA: A minimum of 3”.
c.
Electrical Equipment Rating More Than 5 kVA: A minimum of 6”.
Separation between Communications Cables and Electrical Motors and Transformers, 5
kVA or HP and Larger: A minimum of 48”.
Separation between Communications Cables and Fluorescent Fixtures: Minimum of 5”.
FIRESTOPPING
A.
Comply with requirements in Division 7 Section "Through-Penetration Firestop Systems."
B.
Comply with TIA/EIA-569-A, Annex A, "Firestopping."
C.
Comply with BICSI TDMM, "Firestopping Systems" Article.
3.5
GROUNDING
A.
Install grounding according to BICSI TDMM, "Grounding, Bonding, and Electrical Protection"
Chapter.
B.
Comply with ANSI-J-STD-607-A.
C.
Locate grounding bus bar to minimize the length of bonding conductors. Fasten to wall allowing
at least 2” clearance behind the grounding bus bar. Connect grounding bus bar with a minimum
No. 4 AWG grounding electrode conductor from grounding bus bar to suitable electrical building
ground.
D.
Bond metallic equipment to the grounding bus bar, using not smaller than No. 6 AWG
equipment grounding conductor.
3.6
IDENTIFICATION
A.
Identify system components, wiring, and cabling complying with TIA/EIA-606-A. Comply with
requirements for identification specified in Division 16 Section "Electrical Identification."
COMMUNICATIONS HORIZONTAL CABLING
16717 - 6
KCS ANDREWS HEIGHTS ADDITIONS AND RENOVATIONS
9/6/16
B.
Cabling Administration Drawings: Show building floor plans with cabling administration-point
labeling. Identify labeling convention and show labels for telecommunications closets,
backbone pathways and cables, entrance pathways and cables, terminal hardware and
positions, horizontal cables, work areas and workstation terminal positions, grounding buses
and pathways, and equipment grounding conductors. Follow convention of TIA/EIA-606-A.
Furnish electronic record of all drawings, in software and format selected by Owner.
C.
Cable and Wire Identification:
1.
2.
3.
4.
5.
6.
D.
Labels shall be preprinted or computer-printed type with printing area and font color that
contrasts with cable jacket color but still complies with requirements in TIA/EIA-606-A.
1.
3.7
Label each cable within 4” of each termination and tap, where it is accessible in a cabinet
or junction or outlet box, and elsewhere as indicated.
Each wire connected to building-mounted devices is not required to be numbered at
device if color of wire is consistent with associated wire connected and numbered within
panel or cabinet.
Exposed Cables and Cables in Cable Trays and Wire Troughs: Label each cable at
intervals not exceeding 15’.
Label each terminal strip and screw terminal in each cabinet, rack, or panel.
a.
Individually number wiring conductors connected to terminal strips, and identify
each cable or wiring group being extended from a panel or cabinet to a buildingmounted device shall be identified with name and number of particular device as
shown.
b.
Label each unit and field within distribution racks and frames.
Identification within Connector Fields in Equipment Rooms and Wiring Closets: Label
each connector and each discrete unit of cable-terminating and connecting hardware.
Where similar jacks and plugs are used for both voice and data communication cabling,
use a different color for jacks and plugs of each service.
Uniquely identify and label work area cables extending from the MUTOA to the work
area. These cables may not exceed the length stated on the MUTOA label.
Cables use flexible vinyl or polyester that flex as cables are bent.
FIELD QUALITY CONTROL
A.
Tests and Inspections:
1.
2.
3.
4.
5.
Visually inspect UTP and optical fiber cable jacket materials for NRTL certification
markings.
Inspect cabling terminations in communications equipment rooms for
compliance with color-coding for pin assignments, and inspect cabling connections for
compliance with TIA/EIA-568-B.1.
Visually confirm Category 5e, marking of outlets, cover plates, outlet/connectors, and
patch panels.
Visually inspect cable placement, cable termination, grounding and bonding, equipment
and patch cords, and labeling of all components.
Test UTP backbone copper cabling for DC loop resistance, shorts, opens, intermittent
faults, and polarity between conductors. Test operation of shorting bars in connection
blocks. Test cables after termination but not cross-connection.
a.
Test instruments shall meet or exceed applicable requirements in TIA/EIA-568-B.2.
Perform tests with a tester that complies with performance requirements in "Test
Instruments (Normative)" Annex, complying with measurement accuracy specified
in "Measurement Accuracy (Informative)" Annex. Use only test cords and
adapters that are qualified by test equipment manufacturer for channel or link test
configuration.
UTP Performance Tests:
COMMUNICATIONS HORIZONTAL CABLING
16717 - 7
KCS ANDREWS HEIGHTS ADDITIONS AND RENOVATIONS
9/6/16
a.
6.
7.
Test for each outlet and MUTOA. Perform the following tests according to
TIA/EIA-568-B.1 and TIA/EIA-568-B.2:
1)
Wire map.
2)
Length (physical vs. electrical, and length requirements).
3)
Insertion loss.
4)
Near-end crosstalk (NEXT) loss.
5)
Power sum near-end crosstalk (PSNEXT) loss.
6)
Equal-level far-end crosstalk (ELFEXT).
7)
Power sum equal-level far-end crosstalk (PSELFEXT).
8)
Return loss.
9)
Propagation delay.
10) Delay skew.
Coaxial Cable Tests: Conduct tests according to Division 16 Section "Master Antenna
Television System."
Final Verification Tests: Perform verification tests for UTP systems after the complete
communications cabling and workstation outlet/connectors are installed.
a.
Voice Tests: These tests assume that dial tone service has been installed.
Connect to the network interface device at the demarcation point. Go off-hook and
listen and receive a dial tone. If a test number is available, make and receive a
local, long distance, and digital subscription line telephone call.
b.
Data Tests: These tests assume the Information Technology Staff has a network
installed and is available to assist with testing. Connect to the network interface
device at the demarcation point. Log onto the network to ensure proper
connection to the network.
B.
Document data for each measurement. Data for submittals shall be printed in a summary report
that is formatted similar to Table 10.1 in BICSI TDMM, or transferred from the instrument to the
computer, saved as text files, and printed and submitted.
C.
End-to-end cabling will be considered defective if it does not pass tests and inspections.
D.
Prepare test and inspection reports.
END OF SECTION 16717
COMMUNICATIONS HORIZONTAL CABLING
16717 - 8
KCS ANDREWS HEIGHTS ADDITIONS AND RENOVATIONS
9/6/16
SECTION 16718 - CONDUCTORS AND CABLES FOR ELECTRONIC SAFETY AND SECURITY
PART 1 - GENERAL
1.1
SUMMARY
A.
Section Includes:
1.
2.
3.
4.
5.
6.
7.
8.
1.2
UTP cabling.
62.5/125-micrometer, multimode optical fiber cabling.
RS-232 cabling.
RS-485 cabling.
Low-voltage control cabling.
Control-circuit conductors.
Fire alarm wire and cable.
Identification products.
DEFINITIONS
A.
BICSI: Building Industry Consulting Service International.
B.
EMI: Electromagnetic interference.
C.
IDC: Insulation displacement connector.
D.
Open Cabling: Passing telecommunications cabling through open space (e.g., between the
studs of a wall cavity).
E.
RCDD: Registered Communications Distribution Designer.
1.3
SUBMITTALS
A.
Product Data: For each type of product indicated.
B.
Shop Drawings: Cable tray layout, showing cable tray route to scale, with relationship between
the tray and adjacent structural, electrical, and mechanical elements.
C.
Qualification Data: For qualified layout technician, installation supervisor, and field inspector.
D.
Seismic Qualification Certificates:
manufacturer.
E.
Source quality-control reports.
F.
Field quality-control reports.
G.
Operation and maintenance data.
1.4
For pathways, accessories, and components, from
QUALITY ASSURANCE
A.
Testing Agency Qualifications: An NRTL.
1.
Testing Agency's Field Supervisor: Currently certified by BICSI as an RCDD to supervise
on-site testing.
CONDUCTORS AND CABLES FOR ELECTRONIC SAFETY AND SECURITY
16718 - 1
KCS ANDREWS HEIGHTS ADDITIONS AND RENOVATIONS
B.
Surface-Burning Characteristics: As determined by testing identical products according to
ASTM E 84 by a qualified testing agency. Identify products with appropriate markings of
applicable testing agency.
1.
2.
C.
1.5
9/6/16
Flame-Spread Index: 25or less.
Smoke-Developed Index: 50 or less.
Electrical Components, Devices, and Accessories: Listed and labeled as defined in NFPA 70,
by a qualified testing agency, and marked for intended location and application.
DELIVERY, STORAGE, AND HANDLING
A.
Test cables upon receipt at Project site.
1.
2.
3.
1.6
Test optical fiber cable to determine the continuity of the strand end to end. Use opticalfiber flashlight or optical loss test set.
Test optical fiber cable on reels. Use an optical time domain reflectometer to verify the
cable length and locate cable defects, splices, and connector; include the loss value of
each. Retain test data and include the record in maintenance data.
Test each pair of UTP cable for open and short circuits.
PROJECT CONDITIONS
A.
Do not install conductors and cables that are wet, moisture damaged, or mold damaged.
1.
B.
Indications that wire and cables are wet or moisture damaged include, but are not limited
to, discoloration and sagging of factory packing materials.
Environmental Limitations: Do not deliver or install UTP, optical fiber, and coaxial cables and
connecting materials until wet work in spaces is complete and dry, and temporary HVAC system
is operating and maintaining ambient temperature and humidity conditions at occupancy levels
during the remainder of the construction period.
PART 2 - PRODUCTS
2.1
PATHWAYS
A.
Support of Open Cabling: NRTL labeled for support of Category 5e cabling, designed to
prevent degradation of cable performance and pinch points that could damage cable.
B.
Cable Trays:
1.
C.
Manufacturers: Subject to compliance with requirements, provide products by one of the
following:
a.
Allied Tube & Conduit; a business unit of Tyco Electrical & Metal Products.
b.
Cablofil.
c.
Cooper B-Line, Inc.
d.
GS Metals Corp.
e.
Snaketray; Cable Management Solutions, Inc.
Conduit and Boxes: Comply with requirements in Division 16 Section "Raceways and Boxes."
1.
Outlet boxes shall be no smaller than 2” wide, 3” high, and 2-1/2” deep.
CONDUCTORS AND CABLES FOR ELECTRONIC SAFETY AND SECURITY
16718 - 2
KCS ANDREWS HEIGHTS ADDITIONS AND RENOVATIONS
2.2
9/6/16
BACKBOARDS
A.
2.3
Backboards: Plywood, 3/4” x 48” x 96”. Comply with requirements for plywood backing panels
in Division 6 Section "Rough Carpentry".
UTP CABLE
A.
Manufacturers:
following:
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
B.
ADC.
AMP Netconnect; a brand of Tyco Electronics Corporation.
Belden CDT Networking Division/NORDX.
Belden Inc.
Berk-Tek; a Nexans company.
CommScope, Inc.
Draka Cableteq USA.
Genesis Cable Products; Honeywell International, Inc.
Mohawk; a division of Belden.
Superior Essex Inc.
SYSTIMAX Solutions; a CommScope, Inc. brand.
3M; Communication Markets Division.
Description: 100-ohm, 4-pair UTP, covered with a blue thermoplastic jacket.
1.
2.
3.
4.
2.4
Subject to compliance with requirements, provide products by one of the
Comply with ICEA S-90-661 for mechanical properties.
Comply with TIA/EIA-568-B.1 for performance specifications.
Comply with TIA/EIA-568-B.2, Category 5e.
Listed and labeled by an NRTL acceptable to authorities having jurisdiction as complying
with UL 444 and NFPA 70 for the following types:
a.
Communications, Plenum Rated: Type CMP or MPP, complying with NFPA 262.
b.
Communications, Riser Rated: Type CMR or MPR, complying with UL 1666.
c.
Communications, Limited Purpose: Type CMX; or CMP.
d.
Multipurpose, Plenum Rated: Type MPP, complying with NFPA 262.
e.
Multipurpose, Riser Rated: Type MPR, complying with UL 1666.
UTP CABLE HARDWARE
A.
Manufacturers:
following:
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
B.
Subject to compliance with requirements, provide products by one of the
ADC.
American Technology Systems Industries, Inc.
AMP Netconnect; a brand of Tyco Electronics Corporation.
Belden CDT Networking Division/NORDX.
Dynacom Corporation.
Hubbell Incorporated; Hubbell Premise Wiring.
Leviton Voice & Data Division.
Molex Premise Networks; a division of Molex, Inc.
PANDUIT CORP.
Siemon.
UTP Cable Connecting Hardware: IDC type, using modules designed for punch-down caps or
tools. Cables shall be terminated with connecting hardware of the same category or higher.
CONDUCTORS AND CABLES FOR ELECTRONIC SAFETY AND SECURITY
16718 - 3
KCS ANDREWS HEIGHTS ADDITIONS AND RENOVATIONS
C.
2.5
9/6/16
Connecting Blocks: 110-style for Category 5e. Provide blocks for the number of cables
terminated on the block, plus 25% spare. Integral with connector bodies, including plugs and
jacks where indicated.
OPTICAL FIBER CABLE
A.
Manufacturers:
following:
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
B.
5.
6.
Comply with ICEA S-83-596 for mechanical properties.
Comply with TIA/EIA-568-B.3 for performance specifications.
Comply with TIA-492AAAB and TIA-492AAAA-A for detailed specifications.
Listed and labeled by an NRTL acceptable to authorities having jurisdiction as complying
with UL 444, UL 1651, and NFPA 70 for the following types:
a.
Plenum Rated, Nonconductive: Type OFNP, complying with NFPA 262.
b.
Riser Rated, Nonconductive: Type OFNR, complying with UL 1666.
Maximum Attenuation: 3.50 dB/km at 850 nm; 1.5 dB/km at 1300 nm.
Minimum Modal Bandwidth: 160 MHz-km at 850 nm; 500 MHz-km at 1300 nm.
Jacket:
1.
2.
3.
2.6
AMP Netconnect; a brand of Tyco Electronics Corporation.
Belden CDT Networking Division/NORDX.
Berk-Tek; a Nexans company.
CommScope, Inc.
Corning Incorporated; Corning Cable Systems.
CSI Technologies Inc.
General Cable Technologies Corporation.
Mohawk; a division of Belden.
Superior Essex Inc.
SYSTIMAX Solutions; a CommScope, Inc. brand.
3M; Communication Markets Division.
Description: Multimode, 62.5/125-micrometer, 24 fiber, nonconductive, tight buffer, optical fiber
cable.
1.
2.
3.
4.
C.
Subject to compliance with requirements, provide products by one of the
Jacket Color: Orange for 62.5/125-micrometer cable.
Cable cordage jacket, fiber, unit, and group color shall be according to TIA-598-C.
Imprinted with fiber count, fiber type, and aggregate length at regular intervals not to
exceed 40”.
OPTICAL FIBER CABLE HARDWARE
A.
Manufacturers:
following:
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
Subject to compliance with requirements, provide products by one of the
ADC.
American Technology Systems Industries, Inc.
Belden CDT Networking Division/NORDX.
Berk-Tek; a Nexans company.
Corning Incorporated; Corning Cable Systems.
CSI Technologies Inc.
Dynacom Corporation.
Hubbell Incorporated; Hubbell Premise Wiring.
Molex Premise Networks; a division of Molex, Inc.
Siemon.
CONDUCTORS AND CABLES FOR ELECTRONIC SAFETY AND SECURITY
16718 - 4
KCS ANDREWS HEIGHTS ADDITIONS AND RENOVATIONS
B.
Cable Connecting Hardware: Meet the Optical Fiber Connector Intermateability Standards
(FOCIS) specifications of TIA-604-2-B, TIA-604-3-B, and TIA/EIA-604-12. Comply with
TIA/EIA-568-B.3.
1.
2.
2.7
9/6/16
Quick-connect, simplex and duplex, Type SC, Type ST, Type LC or Type MT-RJ
connectors. Insertion loss not more than 0.75 dB.
Type SFF connectors may be used in termination racks, panels, and equipment
packages.
RS-232 CABLE
A.
Standard Cable: NFPA 70, Type CM.
1.
2.
3.
4.
5.
6.
B.
Plenum-Rated Cable: NFPA 70, Type CMP.
1.
2.
3.
4.
5.
6.
2.8
Paired, 2 pairs, No. 22 AWG, stranded (7x30) tinned copper conductors.
Polypropylene insulation.
Individual aluminum foil-polyester tape shielded pairs with 100% shield coverage.
PVC jacket.
Pairs are cabled on common axis with No. 24 AWG, stranded (7x32) tinned copper drain
wire.
Flame Resistance: Comply with UL 1581.
Paired, 2 pairs, No. 22 AWG, stranded (7x30) tinned copper conductors.
Plastic insulation.
Individual aluminum foil-polyester tape shielded pairs with 100% shield coverage.
Plastic jacket.
Pairs are cabled on common axis with No. 24 AWG, stranded (7x32) tinned copper drain
wire.
Flame Resistance: Comply with NFPA 262.
RS-485 CABLE
A.
Standard Cable: NFPA 70, Type CM or CMG.
1.
2.
3.
4.
5.
B.
Plenum-Rated Cable: NFPA 70, Type CMP.
1.
2.
3.
4.
5.
2.9
Paired, 2 pairs, twisted, No. 22 AWG, stranded (7x30) tinned copper conductors.
PVC insulation.
Unshielded.
PVC jacket.
Flame Resistance: Comply with UL 1581.
Paired, 2 pairs, No. 22 AWG, stranded (7x30) tinned copper conductors.
Fluorinated ethylene propylene insulation.
Unshielded.
Fluorinated ethylene propylene jacket.
Flame Resistance: NFPA 262, Flame Test.
LOW-VOLTAGE CONTROL CABLE
A.
Paired Cable: NFPA 70, Type CMG.
1.
2.
1 pair, twisted, No. 16 AWG, stranded (19x29) or No. 18 AWG, stranded (19x30) tinned
copper conductors.
PVC insulation.
CONDUCTORS AND CABLES FOR ELECTRONIC SAFETY AND SECURITY
16718 - 5
KCS ANDREWS HEIGHTS ADDITIONS AND RENOVATIONS
3.
4.
5.
B.
Unshielded.
PVC jacket.
Flame Resistance: Comply with UL 1581.
Plenum-Rated, Paired Cable: NFPA 70, Type CMP.
1.
2.
3.
4.
5.
2.10
9/6/16
1 pair, twisted, No. 16 AWG, stranded (19x29) or No. 18 AWG, stranded (19x30) tinned
copper conductors.
PVC insulation.
Unshielded.
PVC jacket.
Flame Resistance: Comply with NFPA 262.
CONTROL-CIRCUIT CONDUCTORS
A.
Class 1 Control Circuits: Stranded copper, Type THHN-THWN, complying with UL 83, in
raceway or Type XHHN, complying with UL 44, in raceway.
B.
Class 2 Control Circuits: Stranded copper, Type THHN-THWN, complying with UL 83, in
raceway, power-limited tray cable, complying with UL 83, in cable tray or Type XHHN,
complying with UL 44, in raceway.
C.
Class 3 Remote-Control and Signal Circuits: Stranded copper, Type TW or TF, complying with
UL 83.
2.11
A.
FIRE ALARM WIRE AND CABLE
Manufacturers:
following:
1.
2.
3.
4.
5.
Subject to compliance with requirements, provide products by one of the
Comtran Corporation.
Draka Cableteq USA.
Genesis Cable Products; Honeywell International, Inc.
Rockbestos-Suprenant Cable Corp.
West Penn Wire; a brand of Belden Inc.
B.
General Wire and Cable Requirements: NRTL listed and labeled as complying with NFPA 70,
Article 760.
C.
Signaling Line Circuits:
manufacturer.
1.
D.
Twisted, shielded pair, wire size as recommended by system
Circuit Integrity Cable: Twisted shielded pair, NFPA 70, Article 760, Classification CI, for
power-limited fire alarm signal service Type FPL. NRTL listed and labeled as complying
with UL 1424 and UL 2196 for a 2-hour rating.
Non-Power-Limited Circuits:
insulation.
1.
2.
3.
Solid-copper conductors with 600-V rated, 75° C, color-coded
Low-Voltage Circuits: No. 16 AWG, minimum.
Line-Voltage Circuits: No. 12 AWG, minimum.
Multiconductor Armored Cable:
NFPA 70, Type MC, copper conductors,
Type TFN/THHN conductor insulation, copper drain wire, copper armor with red identifier
stripe, NTRL listed for fire alarm and cable tray installation, plenum rated, and complying
with requirements in UL 2196 for a 2-hour rating.
CONDUCTORS AND CABLES FOR ELECTRONIC SAFETY AND SECURITY
16718 - 6
KCS ANDREWS HEIGHTS ADDITIONS AND RENOVATIONS
E.
2.12
A.
9/6/16
All fire alarm cables must be in conduit.
IDENTIFICATION PRODUCTS
Manufacturers:
following:
1.
2.
3.
4.
Subject to compliance with requirements, provide products by one of the
Brady Corporation.
HellermannTyton.
Kroy LLC.
PANDUIT CORP.
B.
Comply with UL 969 for a system of labeling materials, including label stocks, laminating
adhesives, and inks used by label printers.
C.
Comply with requirements in Division 16 Section "Electrical Identification."
2.13
SOURCE QUALITY CONTROL
A.
Factory test UTP and optical fiber cables on reels according to TIA/EIA-568-B.1.
B.
Factory test UTP cables according to TIA/EIA-568-B.2.
C.
Factory test multimode optical fiber cables according to TIA-526-14-A and TIA/EIA-568-B.3.
D.
Cable will be considered defective if it does not pass tests and inspections.
E.
Prepare test and inspection reports.
PART 3 - EXECUTION
3.1
INSTALLATION OF PATHWAYS
A.
Cable Trays: Comply with NEMA VE 2 and TIA-569-B.
B.
Comply with TIA-569-B for pull-box sizing and length of conduit and number of bends between
pull points.
C.
Comply with requirements in Division 16 Section "Raceways and Boxes" for installation of
conduits and wireways.
D.
Install manufactured conduit sweeps and long-radius elbows whenever possible.
E.
Pathway Installation in Equipment Rooms:
1.
2.
3.
4.
5.
F.
Position conduit ends adjacent to a corner on backboard where a single piece of plywood
is installed or in the corner of room where multiple sheets of plywood are installed around
perimeter walls of room.
Install cable trays to route cables if conduits cannot be located in these positions.
Secure conduits to backboard when entering room from overhead.
Extend conduits 3” above finished floor.
Install metal conduits with grounding bushings and connect with grounding conductor to
grounding system.
Backboards: Install backboards with 96” dimension vertical. Butt adjacent sheets tightly, and
form smooth gap-free corners and joints.
CONDUCTORS AND CABLES FOR ELECTRONIC SAFETY AND SECURITY
16718 - 7
KCS ANDREWS HEIGHTS ADDITIONS AND RENOVATIONS
3.2
9/6/16
INSTALLATION OF HANGERS AND SUPPORTS
A.
3.3
Comply with requirements in Division 16 Section "Hangers and Supports for Electrical Systems"
for installation of supports for pathways, conductors and cables.
WIRING METHOD
A.
Install wiring in metal raceways and wireways. Conceal raceway except in unfinished spaces
and as indicated. Minimum conduit size shall be 3/4”. Control and data transmission wiring
shall not share conduit with other building wiring systems.
B.
Install wiring in raceways except in accessible indoor ceiling spaces and in interior hollow
gypsum board partitions where cable may be used. Conceal raceways and wiring except in
unfinished spaces and as indicated. Minimum conduit size shall be 3/4”. Control and data
transmission wiring shall not share conduit with other building wiring systems.
C.
Install cable, concealed in accessible ceilings, walls, and floors when possible.
D.
Wiring within Enclosures: Bundle, lace, and train conductors to terminal points. Use lacing bars
and distribution spools.
Separate power-limited and non-power-limited conductors as
recommended in writing by manufacturer. Install conductors parallel with or at right angles to
sides and back of enclosure. Connect conductors that are terminated, spliced, or interrupted in
any enclosure associated with intrusion system to terminal blocks. Mark each terminal
according to system's wiring diagrams. Make all connections with approved crimp-on terminal
spade lugs, pressure-type terminal blocks, or plug connectors.
3.4
INSTALLATION OF CONDUCTORS AND CABLES
A.
Comply with NECA 1.
B.
Conductors:
indicated.
C.
General Requirements for Cabling:
1.
2.
3.
4.
5.
6.
7.
8.
D.
Size according to system manufacturer's written instructions unless otherwise
Comply with TIA/EIA-568-B.1.
Comply with BICSI ITSIM, Ch. 6, "Cable Termination Practices."
Terminate all conductors; no cable shall contain unterminated elements.
Make
terminations only at indicated outlets, terminals, and cross-connect and patch panels.
Cables may not be spliced. Secure and support cables at intervals not exceeding 30”
and not more than 6” from cabinets, boxes, fittings, outlets, racks, frames, and terminals.
Bundle, lace, and train conductors to terminal points without exceeding manufacturer's
limitations on bending radii, but not less than radii specified in BICSI ITSIM, "Cabling
Termination Practices" Chapter. Install lacing bars and distribution spools.
Do not install bruised, kinked, scored, deformed, or abraded cable. Do not splice cable
between termination, tap, or junction points. Remove and discard cable if damaged
during installation and replace it with new cable.
Cold-Weather Installation: Bring cable to room temperature before dereeling. Heat
lamps shall not be used for heating.
Pulling Cable: Comply with BICSI ITSIM, Ch. 4, "Pulling Cable." Monitor cable pull
tensions.
UTP Cable Installation: Install using techniques, practices, and methods that are consistent
with Category 5e rating of components and that ensure Category 5e performance of completed
and linked signal paths, end to end.
CONDUCTORS AND CABLES FOR ELECTRONIC SAFETY AND SECURITY
16718 - 8
KCS ANDREWS HEIGHTS ADDITIONS AND RENOVATIONS
1.
2.
3.
E.
2.
3.
Install cabling with horizontal and vertical cable guides in telecommunications spaces
with terminating hardware and interconnection equipment.
Suspend copper cable not in a wireway or pathway a minimum of 8” above ceilings by
cable supports not more than 60” apart.
Cable shall not be run through structural members or in contact with pipes, ducts, or
other potentially damaging items.
Separation from EMI Sources:
1.
2.
3.
4.
5.
6.
3.5
Comply with TIA/EIA-568-B.3.
Cable shall be terminated on connecting hardware that is rack or cabinet mounted.
Open-Cable Installation:
1.
G.
Comply with TIA/EIA-568-B.2.
Install 110-style IDC termination hardware unless otherwise indicated.
Do not untwist UTP cables more than 1/2” from the point of termination to maintain cable
geometry.
Optical Fiber Cable Installation:
1.
2.
F.
9/6/16
Comply with BICSI TDMM and TIA-569-B recommendations for separating unshielded
copper voice and data communication cable from potential EMI sources, including
electrical power lines and equipment.
Separation between open communications cables or cables in nonmetallic raceways and
unshielded power conductors and electrical equipment shall be as follows:
a.
Electrical Equipment Rating Less Than 2 kVA: A minimum of 5”.
b.
Electrical Equipment Rating between 2 and 5 kVA: A minimum of 12”.
c.
Electrical Equipment Rating More Than 5 kVA: A minimum of 24”.
Separation between communications cables in grounded metallic raceways and
unshielded power lines or electrical equipment shall be as follows:
a.
Electrical Equipment Rating Less Than 2 kVA: A minimum of 2-1/2”.
b.
Electrical Equipment Rating between 2 and 5 kVA: A minimum of 6”.
c.
Electrical Equipment Rating More Than 5 kVA: A minimum of 12”.
Separation between communications cables in grounded metallic raceways and power
lines and electrical equipment located in grounded metallic conduits or enclosures shall
be as follows:
a.
Electrical Equipment Rating Less Than 2 kVA: No requirement.
b.
Electrical Equipment Rating between 2 and 5 kVA: A minimum of 3”.
c.
Electrical Equipment Rating More Than 5 kVA: A minimum of 6”.
Separation between Cables and Electrical Motors and Transformers, 5 kVA or HP and
Larger: A minimum of 48”.
Separation between Cables and Fluorescent Fixtures: A minimum of 5”.
FIRE ALARM WIRING INSTALLATION
A.
Comply with NECA 1 and NFPA 72.
B.
Wiring Method: Install wiring in metal raceway according to Division 16 Section "Raceways and
Boxes."
1.
2.
C.
Install plenum cable in environmental air spaces, including plenum ceilings.
Fire alarm circuits and equipment control wiring associated with the fire alarm system
shall be installed in a dedicated raceway system. This system shall not be used for any
other wire or cable.
Wiring Method:
CONDUCTORS AND CABLES FOR ELECTRONIC SAFETY AND SECURITY
16718 - 9
KCS ANDREWS HEIGHTS ADDITIONS AND RENOVATIONS
1.
2.
3.
9/6/16
Cables and raceways used for fire alarm circuits, and equipment control wiring
associated with the fire alarm system, may not contain any other wire or cable.
Fire-Rated Cables: Use of 2-hour, fire-rated fire alarm cables, NFPA 70, Types MI and
CI, is permitted.
Signaling Line Circuits: Power-limited fire alarm cables may be installed in the same
cable or raceway as signaling line circuits.
D.
Wiring within Enclosures: Separate power-limited and non-power-limited conductors as
recommended by manufacturer. Install conductors parallel with or at right angles to sides and
back of the enclosure. Bundle, lace, and train conductors to terminal points with no excess.
Connect conductors that are terminated, spliced, or interrupted in any enclosure associated with
the fire alarm system to terminal blocks. Mark each terminal according to the system's wiring
diagrams. Make all connections with approved crimp-on terminal spade lugs, pressure-type
terminal blocks, or plug connectors.
E.
Cable Taps: Use numbered terminal strips in junction, pull, and outlet boxes, cabinets, or
equipment enclosures where circuit connections are made.
F.
Color-Coding: Color-code fire alarm conductors differently from the normal building power
wiring. Use one color-code for alarm circuit wiring and another for supervisory circuits. Colorcode audible alarm-indicating circuits differently from alarm-initiating circuits. Use different
colors for visible alarm-indicating devices. Paint fire alarm system junction boxes and covers
red.
G.
Risers: Install at least two vertical cable risers to serve the fire alarm system. Separate risers
in close proximity to each other with a minimum one-hour-rated wall, so the loss of one riser
does not prevent the receipt or transmission of signals from other floors or zones.
H.
Wiring to Remote Alarm Transmitting Device: 1” conduit between the fire alarm control panel
and the transmitter. Install number of conductors and electrical supervision for connecting
wiring as needed to suit monitoring function.
3.6
POWER AND CONTROL-CIRCUIT CONDUCTORS
A.
120-V Power Wiring: Install according to Division 16 Section "Conductors and Cables" unless
otherwise indicated.
B.
Minimum Conductor Sizes:
1.
2.
3.
3.7
Class 1 remote-control and signal circuits, No. 14 AWG.
Class 2 low-energy, remote-control and signal circuits, No. 16 AWG.
Class 3 low-energy, remote-control, alarm and signal circuits, No. 12 AWG.
FIRESTOPPING
A.
Comply with requirements in Division 7 Section "Through-Penetration Firestop Systems."
B.
Comply with TIA-569-B, "Firestopping" Annex A.
C.
Comply with BICSI TDMM, "Firestopping Systems" Article.
3.8
GROUNDING
A.
For communications wiring, comply with ANSI-J-STD-607-A and with BICSI TDMM, "Grounding,
Bonding, and Electrical Protection" Chapter.
CONDUCTORS AND CABLES FOR ELECTRONIC SAFETY AND SECURITY
16718 - 10
KCS ANDREWS HEIGHTS ADDITIONS AND RENOVATIONS
B.
3.9
9/6/16
For low-voltage wiring and cabling, comply with requirements in Division 16 Section "Grounding
and Bonding."
IDENTIFICATION
A.
3.10
Identify system components, wiring, and cabling complying with TIA/EIA-606-A. Comply with
requirements for identification specified in Division 16 Section "Electrical Identification."
FIELD QUALITY CONTROL
A.
Perform tests and inspections.
B.
Tests and Inspections:
1.
2.
3.
4.
Visually inspect UTP and optical fiber cable jacket materials for NRTL certification
markings. Inspect cabling terminations to confirm color-coding for pin assignments, and
inspect cabling connections to confirm compliance with TIA/EIA-568-B.1.
Visually inspect cable placement, cable termination, grounding and bonding, equipment
and patch cords, and labeling of all components.
Test UTP cabling for DC loop resistance, shorts, opens, intermittent faults, and polarity
between conductors. Test operation of shorting bars in connection blocks. Test cables
after termination but not cross connection.
a.
Test instruments shall meet or exceed applicable requirements in TIA/EIA-568-B.2.
Perform tests with a tester that complies with performance requirements in "Test
Instruments (Normative)" Annex, complying with measurement accuracy specified
in "Measurement Accuracy (Informative)" Annex. Use only test cords and
adapters that are qualified by test equipment manufacturer for channel or link test
configuration.
Optical Fiber Cable Tests:
a.
Test instruments shall meet or exceed applicable requirements in TIA/EIA-568-B.1.
Use only test cords and adapters that are qualified by test equipment manufacturer
for channel or link test configuration.
b.
Link End-to-End Attenuation Tests:
1)
Multimode Link Measurements: Test at 850 or 1300 nm in 1 direction
according to TIA-526-14-A, Method B, One Reference Jumper.
2)
Attenuation test results for links shall be less than 2.0 dB. Attenuation test
results shall be less than that calculated according to equation in TIA/EIA568-B.1.
C.
Document data for each measurement. Print data for submittals in a summary report that is
formatted using Table 10.1 in BICSI TDMM as a guide, or transfer the data from the instrument
to the computer, save as text files, print, and submit.
D.
End-to-end cabling will be considered defective if it does not pass tests and inspections.
E.
Prepare test and inspection reports.
END OF SECTION 16718
CONDUCTORS AND CABLES FOR ELECTRONIC SAFETY AND SECURITY
16718 - 11
KCS – ANDREWS HEIGHTS ADDITIONS AND RENOVATIONS
9/8/16
SECTION 16789 – INTEGRATED SECURITY MANAGEMENT SYSTEM
PART 1 - GENERAL
1.1
RELATED DOCUMENTS
A.
1.2
Drawings and general provisions of the Contract, including General and Supplementary
Conditions and Division 1 Specification Sections, apply to this Section.
SUMMARY
A.
1.3
System Description: The Security Management System consisting of Access Control, Personnel
Database, CCTV Surveillance Cameras, DVR Recorders, Visitor Intercom System, Intrusion
Detection Alarms, and Remote Monitoring shall be connected to and interfaced with the existing
Security Management System installed in Kanawha County. The existing Database Server
located at the KCS Board of Education Central Office shall receive all new Personnel Files for
the Access Control System.
SUBMITTALS
A.
Product Data: For each type of product indicated. Include rated capacities, operating
characteristics, and furnished specialties and accessories. Reference each product to a
location on Drawings.
B.
Shop Drawings: Include plans, elevations, sections, details, and attachments to other work. All
shop drawings shall be prepared in Visio Professional or AutoCAD software. In addition to the
drawings, the Contractor shall furnish a USB Drive containing the identical information.
C.
Shop drawings shall include:
1.
2.
Diagrams for cable management system.
System labeling schedules, including electronic copy of labeling schedules that are part
of the cable and asset identification system of the software specified in Parts 2 and 3.
D.
Submittal data shall contain manufacturer's data on all hardware and software products
required by the specification.
E.
Software submittals shall contain narrative descriptions of sequences of operation, program
listings, point lists, and a complete description of the graphics, reports, alarms and configuration
to be furnished with the workstation software. Information shall be bound or in a three ring
binder with an index and tabs.
F.
Field quality-control reports.
1.4
SYSTEM OPERATING AND MAINTENANCE MANUALS
A.
Operation and maintenance manuals shall contain all information necessary for the operation,
maintenance, replacement, installation, and parts procurement for the entire Integrated Security
/ Building Management System. This documentation shall include specific part numbers and
software versions and dates. A complete list of recommended spare parts shall be included
with the lead time and expected frequency of use of each part clearly identified.
B.
Following project completion and testing, the Integrated Security / Building Management
System Vendor will submit as-built drawings reflecting the exact installation of the system. The
as-built documentation shall also include a copy of all application software both in written form
and on diskette.
INTEGRATED SECURITY/BUILDING MANAGEMENT SYSTEM
16789 - 1
KCS – ANDREWS HEIGHTS ADDITIONS AND RENOVATIONS
C.
Operation and Maintenance Data: For security system to include, operation, and maintenance
manuals. In addition to items specified in Division 1 Section "Operation and Maintenance
Data," include the following:
1.
2.
1.5
9/8/16
Hard copies of manufacturer's specification sheets, operating specifications, design
guides, user's guides for software and hardware, and PDF files on CD-ROM of the hardcopy submittal.
System installation and setup guides with data forms to plan and record options and
setup decisions.
WARRANTY
A.
The Integrated Security / Building Management System Vendor shall warrant the system for 12
months after system acceptance and beneficial use by the owner. During the warranty period,
the Integrated Security Management System Vendor shall be responsible for all necessary
revisions to the software as required to provide a complete and workable system consistent with
the intent of the Description of Operation. The Integrated Security / Building Management
System Vendor shall provide as part of the warranty period (1) inspection during the first year.
B.
Updates to manufacturer’s software shall be provided at no charge during the warranty period.
1.6
QUALITY ASSURANCE
A.
Qualifications of Bidder: The following bidders have been pre-qualified:
1.
B.
Andover Controls Continuum by Mason & Barry, Inc.
Installer Qualifications: An employer of workers trained and approved by manufacturer.
1.
Cable installer must have on staff a registered communication distribution designer
certified by Building Industry Consulting Service International.
C.
Source Limitations: Obtain central station, workstations, controllers, Identifier readers, and all
software through one source.
D.
Electrical Components, Devices, and Accessories: Listed and labeled as defined in NFPA 70,
by a qualified testing agency, and marked for intended location and application.
E.
Comply with NFPA 70, "National Electrical Code."
F.
Provide SMS components and ancillary equipment, which are UL-916 listed and labeled.
G.
All equipment or wiring used in conditioned air streams, spaces or return air plenums shall
comply with NFPA 90A Flame/Smoke/Fuel contribution rating of 25/50/0 and all applicable
building codes or requirements.
H.
Comply with National Electrical Manufacturers Association (NEMA).
I.
Comply with FCC rules, Part 15 regarding Class A radiation for computing devices and low
power communication equipment operating in commercial environments.
J.
UL-294 Listed Access Control Systems.
K.
Comply with Americans with Disabilities Act (ADA).
INTEGRATED SECURITY/BUILDING MANAGEMENT SYSTEM
16789 - 2
KCS – ANDREWS HEIGHTS ADDITIONS AND RENOVATIONS
9/8/16
PART 2 - PRODUCTS
2.1
MANUFACTURERS
A.
Basis-of-Design Product: Subject to compliance with requirements, provide Standard Kanawha
County Security Management products by following:
1.
2.
3.
4.
5.
6.
7.
8.
2.2
Aiphone Visitor Intercom Systems
Andover Controls Continuum Access / Security Controllers
Besam ADA Door Openers.
HID Access Card Readers.
Easy Lobby, Inc. Drivers License Scanner / Software
Pelco CCTV Camera Systems
Squared-D/Schneider Electric Classroom Occupancy Sensors
Functinal Devices, Inc. Classroom Occupancy Light Relays
DESCRIPTION OF WORK
A.
The Integrated Security System shall consist of all Ethernet Network Continuum Net Controllers,
Network DVR Recorders, VoIP Network Intercom System, Integrated Digital Control Modules,
1-Primary Gatekeeper (Existing), Integrated ADA Handicap Visitor Door Control with indoor and
outdoor push button openers, Access Control Proximity Readers with Key Pad, Drivers License
Scanner, Surveillance Cameras, Zone Motion Sensors, Door Status Sensors, Arming Pads,
Integrated Lighting Control Panels, and other accessory equipment, along with a complete
system of electrical interlock wiring to fill the intent of the specification and provide for a
complete and operable system. Coordinate Field Device location and installation requirements
with the various Contractors.
B.
All Electric Strikes, Power Supplies, and Power Transfer Devices for Access and Scheduled
Doors shall be furnished by the Door Manufacturer and be part of the door. The Door Frame
shall come with rough in openings for Door Status Contacts and Transfer Devices. Coordinate
Device location and installation requirements with the General Trades Contractor.
C.
All interlocking, wiring and installation of all Field Devices associated with the Security
Management Equipment listed above shall be provided under this Contract.
D.
The SMS Vendor shall provide services and manpower necessary for commissioning of the
Security Management System.
E.
All work performed under this section of the specifications shall comply with all codes, laws and
governing bodies. If the drawings and/or specifications are in conflict with governing codes, the
Contractor shall submit a proposal with appropriate modifications to the project to meet code
restrictions. If this specification and associated drawings exceed governing code requirements,
the specification shall govern. Contractor shall obtain and pay for all necessary construction
permits and licenses.
2.3
SYSTEM DESCRIPTION
A.
The Integrated Security Management System shall consist of Network Controllers of modular
design providing distributed processing capability, and allowing unlimited future expansion and
Integration of both input/output points and processing/control functions. For this project the
system shall consist of the following components:
1.
Visitor Intercom System - A VoIP Network Intercom Module shall be provided and the
VoIP Intercom Software shall be loaded onto the Gatekeeper Workstations so the
Operator can talk to the Visitor through the Workstation Microphone and speakers. When
INTEGRATED SECURITY/BUILDING MANAGEMENT SYSTEM
16789 - 3
KCS – ANDREWS HEIGHTS ADDITIONS AND RENOVATIONS
2.
3.
4.
5.
2.4
9/8/16
a Visitor arrives at the Main Visitor Entrance he or she pushes the Intercom Button. The
Graphic Pop Up shall appear and the Intercom shall be activated so the Operator can
see and talk to the Visitor. When not using the Visitor Intercom System, the Operator can
use the Computer for Normal everyday use.
Drivers Licenses Scanner System - Provide a weather proof Drivers Licenses Scanner at
the Visitor Door. When a Visitor pushes the Intercom Button a message will ask him or
her to insert their Drivers Licenses into the Scanner. The Scanner will retrieve the
information from the Drivers License, check the County Database and Sex Offender
Service to see if the Visitor has a problem and is not allowed to enter the building. If there
is a problem the information shall pop up on the Gatekeepers Computer and tell them not
to allow the Visitor into the building.
Card Reader Access Control System - Proximity Card Readers shall be provided at doors
as indicated on drawings. The Readers shall have a key pad for PIN numbers. If a
Kanawha County employee applies a valid card to reader and enters his or her PIN
number the door shall unlock and let them in the building. At the same time if the Security
Intrusion System is armed and active the Valid Access shall also disarm the Security
Alarm System. If the ADA feature is activated on the Employee Card then a Valid Access
shall unlock the door and energize the ADA Door Opener.
CCTV Surveillance System - Provide Security Cameras as indicated on the drawings. All
Cameras shall connect to the Integrated DVR Recorder. A Camera located at the Visitor
Door shall pop up the image of the Visitor on the Gatekeeper Computer when the Visitor
Intercom System is activated. Remote View Software shall be loaded on the Principals
and Vice Principals Computers so they can View and Search all CCTV events.
Security Intrusion / Lighting Control System - Provide Occupancy Sensors, Arming Pads,
Door Status Contacts, and Lighting Control Panels as indicated on the drawings. When
the Security System is Un-armed during the occupied time the Occupancy Sensors shall
control the Lighting Control Panel and remote relays to turn the Lights off and on as
required. Low Voltage Keyed Light Switches in the Corridors shall override the Lighting
Panel at any time to turn on the Lights. When the Security Intrusion System is armed and
no one should be in the building the Occupancy Sensors shall become the Intrusion
Motion Sensors. If motion is detected the System shall turn on the Lights, Sound the
Local Alarm Horn, and send an Alarm Message to the County’s Central Alarm
Workstation for Event Notification. The Security System can be disarmed by entering a
password at the Arming Pad or with a Valid Access using the Card Reader.
SYSTEM ARCHITECTURE
A.
The Integrated Security Management System shall consist of Net Controllers, Input/Output Unit
Modules (IOU Modules), Gatekeeper Workstations, and one existing File Server to support
system configurations. The Integrated Security Management System shall provide Control,
Alarm Detection, Scheduling, Personnel Reporting and Information Management for the entire
facility and Wide Area Network, from a single existing ODBC-compliant database Server located
at the KCS Central Board Office.
B.
Remote Communications: Remote Communications with the Facility shall be through the
County Network. A VPN Client shall permit access to the Maintenance Enterprise Workstation
located at the Central Office. All Personnel and Access Control information shall be entered
through the existing Personnel Workstation located in Human Resources at the Central Office.
All Alarms shall be monitored through the existing Primary Alarm Workstation located at the
KCS Board Office and the Secondary Alarm Workstation located at the Facility Department at
Crede, West Virginia.
C.
System Expansion:
1.
The Integrated Security Management System shall be scalable and expandable at all
levels of the system using the same software interface, and the same Level 1 and Level 2
INTEGRATED SECURITY/BUILDING MANAGEMENT SYSTEM
16789 - 4
KCS – ANDREWS HEIGHTS ADDITIONS AND RENOVATIONS
2.
3.
2.5
9/8/16
controllers. Systems that require replacement of either the workstation software or field
controllers in order to expand the system shall not be acceptable.
The Integrated Security Management System shall be expandable to include HVAC and
Critical Monitoring Control functions at any time in the future with no additional
workstations, front-end software or Level 1 controllers required. Standalone Digital
Control Units or IOU modules shall be able to be added to the existing Level 1 controller’s
field bus, to perform HVAC and Critical Monitoring applications. In this way, an owner’s
existing investment in wiring infrastructure may be leveraged and the cost and
inconvenience of adding new field bus wiring will be minimized.
The system shall use the same application programming language for all levels:
Gatekeeper Workstation, Net Controller Unit, and Standalone Digital Control Units.
Furthermore, this single programming language shall be used for all applications:
environmental control, card access control, intrusion detection and security, lighting
control, leak detection / underground storage tank monitoring, and digital data
communication interfaces to third party microprocessor-based devices.
NET CONTROLLER UNITS
A.
2.6
General - Use Existing Controller.
DIGITAL VIDEO RECORDER
A.
2.7
General - Use the existing Video Recorder located at School.
SURGE AND TAMPER PROTECTION
A.
Surge Protection: Protect components from voltage surges originating external to equipment
housing and entering through power, communication, signal, control, or sensing leads. Include
surge protection for external wiring of each conductor-entry connection to components.
1.
Minimum Protection for Power Connections 120 V.
PART 3 - EXECUTION
3.1
EXAMINATION
A.
Examine pathway elements intended for cables. Check raceways, cable trays, and other
elements for compliance with space allocations, installation tolerances, hazards to cable
installation, and other conditions affecting installation.
B.
Examine roughing-in for LAN and control cable conduit systems to PCs, controllers, card
readers, and other cable-connected devices to verify actual locations of conduit and back boxes
before device installation.
C.
Proceed with installation only after unsatisfactory conditions have been corrected.
3.2
PREPARATION
A.
Comply with recommendations in SIA CP-01.
B.
Comply with TIA/EIA 606-A, "Administration Standard for Commercial Telecommunications
Infrastructure."
INTEGRATED SECURITY/BUILDING MANAGEMENT SYSTEM
16789 - 5
KCS – ANDREWS HEIGHTS ADDITIONS AND RENOVATIONS
C.
3.3
9/8/16
In meetings with Architect and Owner, present Project planning documents and review, adjust,
and prepare final setup documents. Use final documents to set up system software.
CABLING
A.
Comply with NECA 1, "Good Workmanship in Electrical Construction."
B.
Install cables and wiring according to requirements in Division 16 Section "Conductors and
Cables for Electronic Safety and Security."
C.
Wiring Method: Install wiring in raceway and cable tray except within consoles, cabinets, desks,
and counters. Conceal raceway and wiring except in unfinished spaces.
D.
Wiring Method: Install wiring in raceway and cable tray except within consoles, cabinets, desks,
and counters and except in accessible ceiling spaces and in gypsum board partitions where
unenclosed wiring method may be used. Use NRTL-listed plenum cable in environmental
airspaces, including plenum ceilings. Conceal raceway and cables except in unfinished spaces.
E.
Install LAN cables using techniques, practices, and methods that are consistent with Category 6
rating of components and fiber-optic rating of components, and that ensure Category 6 and
fiber-optic performance of completed and linked signal paths, end to end.
F.
Boxes and enclosures containing security-system components or cabling, and which are easily
accessible to employees or to the public, shall be provided with a lock. Boxes above ceiling
level in occupied areas of the building shall not be considered accessible. Junction boxes and
small device enclosures below ceiling level and easily accessible to employees or the public
shall be covered with a suitable cover plate and secured with tamperproof screws.
G.
Install end-of-line resistors at the field device location and not at the controller or panel location.
3.4
GROUNDING
A.
Comply with Division 16 Section "Grounding and Bonding."
B.
Comply with IEEE 1100, "Recommended Practice for Power and Grounding Electronic
Equipment."
C.
Ground cable shields, drain conductors, and equipment to eliminate shock hazard and to
minimize ground loops, common-mode returns, noise pickup, cross talk, and other impairments.
D.
Bond shields and drain conductors to ground at only one point in each circuit.
E.
Signal Ground:
1.
2.
3.
3.5
Terminal: Locate in each equipment room and wiring closet; isolate from power system
and equipment grounding.
Bus: Mount on wall of main equipment room with standoff insulators.
Backbone Cable: Extend from signal ground bus to signal ground terminal in each
equipment room and wiring closet.
IDENTIFICATION
A.
In addition to requirements in this article, comply with applicable requirements in Division 16
Section "Electrical Identification" and with TIA/EIA 606-A.
INTEGRATED SECURITY/BUILDING MANAGEMENT SYSTEM
16789 - 6
KCS – ANDREWS HEIGHTS ADDITIONS AND RENOVATIONS
9/8/16
B.
Using software specified in "Cable and Asset Management Software" Article, develop cable
administration drawings for system identification, testing, and management. Use unique,
alphanumeric designation for each cable, and label cable and jacks, connectors, and terminals
to which it connects with the same designation. Use logical and systematic designations for
facility's architectural arrangement.
C.
Label each terminal strip and screw terminal in each cabinet, rack, or panel.
1.
2.
D.
3.6
All wiring conductors connected to terminal strips shall be individually numbered, and
each cable or wiring group being extended from a panel or cabinet to a building-mounted
device shall be identified with the name and number of the particular device as shown.
Each wire connected to building-mounted devices is not required to be numbered at the
device if the color of the wire is consistent with the associated wire connected and
numbered within the panel or cabinet.
At completion, cable and asset management software shall reflect as-built conditions.
SYSTEM SOFTWARE AND HARDWARE
A.
3.7
Develop, install, and test software and hardware, and perform database tests for the complete
and proper operation of systems involved. Assign software license to Owner.
FIELD QUALITY CONTROL
A.
Manufacturer's Field Service: Engage a factory-authorized service representative to inspect
components, assemblies, and equipment installations, including connections, and to assist in
testing.
B.
Tests and Inspections:
1.
2.
3.
4.
5.
6.
C.
LAN Cable Procedures: Inspect for physical damage and test each conductor signal path
for continuity and shorts. Use Class 2, bidirectional, Category 5 tester. Test for faulty
connectors, splices, and terminations. Test according to TIA/EIA 568-B.1, "Commercial
Building Telecommunications Cabling Standards - Part 1: General Requirements." Link
performance for UTP cables must comply with minimum criteria in TIA/EIA 568-B.1.
Test each circuit and component of each system. Tests shall include, but are not limited
to, measurements of power-supply output under maximum load, signal loop resistance,
and leakage to ground where applicable. System components with battery backup shall
be operated on battery power for a period of not less than 10% of the calculated battery
operating time. Provide special equipment and software if testing requires special or
dedicated equipment.
Operational Test: After installation of cables and connectors, demonstrate product
capability and compliance with requirements. Test each signal path for end-to-end
performance from each end of all pairs installed. Remove temporary connections when
tests have been satisfactorily completed.
See Division 1 Section "Quality Requirements" for retesting and reinspecting
requirements and Division 1 Section "Execution Requirements" for requirements for
correcting the Work.
Devices and circuits will be considered defective if they do not pass tests and
inspections.
Prepare test and inspection reports.
Point to Point Checkout: Each I/O device (both field mounted as well as those located in
Panels) shall be inspected and verified for proper installation and functionality. A checkout
sheet itemizing each device shall be filled out, dated and approved by the Project Manager for
submission to the owner or owner’s representative.
INTEGRATED SECURITY/BUILDING MANAGEMENT SYSTEM
16789 - 7
KCS – ANDREWS HEIGHTS ADDITIONS AND RENOVATIONS
9/8/16
D.
Controller and Workstation Checkout: A field checkout of all controllers and front end
equipment (computers, printers, etc.) shall be conducted to verify proper operation of both
hardware and software. A checkout sheet itemizing each device and a description of the
associated tests shall be prepared and submitted to the owner or owner’s representative by the
completion of the project.
E.
System Acceptance Testing
1.
2.
3.8
When the System is fully installed and operational, the SMS Vendor and representatives
of the Owner shall review and check out the system. At that time, the SMS Vendor shall
demonstrate the operation of the system and prove that it complies with the intent of the
System Specifications and is consistent with the Security Management Systems Installed
in the existing Kanawha County Schools.
Test each alarm in the system and validate that the system generates the appropriate
alarm message, that the message appears at all prescribed destinations (Workstations
and Outlook Distribution), and that any other related actions occur as defined. Submit a
Test Results Sheet to the owner.
CLEANING
A.
3.9
Clean factory finished surfaces. Repair any marred or scratched surfaces with manufacturer's
touch up paint.
SYSTEM START-UP AND COMMISSIONING
A.
Each Integrated Security Management System shall be tested for both hardware and software
functionality and tested against the appropriate description of operation specified herein.
Successful completion of the system test shall constitute the beginning of the warranty period. A
written report will be submitted to the owner indicating that the installed system functions in
accordance with the plans and specifications.
B.
Startup - Startup, test, and adjustment of The Integrated Security Management System shall be
performed by trained personnel in the direct employ of the manufacturer or agent thereof.
Demonstrate compliance with requirements. Replace damaged or malfunctioning controls and
equipment.
Demonstrate all alarm and message displays as described in the sequence of
operation.
C.
The Integrated Security Management System Vendor shall commission and set in operating
condition all new and existing systems such as Access Control Doors, CCTV Cameras, Visitor
Intercom and Scanning System, Intrusion / Lighting Control System, Licenses Scanning
System, Etc. in the presence of the Owner and Architect’s representatives.
D.
Final adjustment: After completion of installation, adjust all Cameras, Readers, Recorders,
Occupancy Sensors, Intercom Systems, and Scanners provided as part of this section. Final
adjustment shall be performed and as-built drawings shall be submitted to the owner. Control
contractor shall furnish a one-year warranty on all components furnished under this section.
E.
Furnish a one-year maintenance contract to include all labor to replace defective parts and
provide software support at no additional cost to the owner. Contract shall include one
inspection per year.
END OF SECTION 16789
INTEGRATED SECURITY/BUILDING MANAGEMENT SYSTEM
16789 - 8