Tempesta™ LED Remote (TA-RMT)
INSTRUCTIONS
IMPORTANT SAFEGUARDS
When using electrical equipment, basic safety precautions should always be followed including the following:
1. READ AND FOLLOW ALL SAFETY INSTRUCTIONS
2. Turn off power supply before attempting to install the unit
3. Do not let power cords touch hot surfaces
4. Do not mount near gas or electric heaters.
5. Equipment should be mounted in locations and at heights where unauthorized personnel will not readily subject it to
tampering.
6. The use of accessory equipment not recommended by Beghelli Canada Inc., may cause an unsafe condition, and
will void the unit’s warranty.
7. Do not use this equipment for other than its intended purpose.
8. Qualified service personnel should perform servicing of this equipment.
9. Consult building code for approved wiring and installation
10. The fixture must be grounded to avoid potential electric shock
11. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
12. SAVE THESE INSTRUCTIONS!
INSTALLATION
NOTE: DC Polarity is critical yellow lead is positive and purple lead is negative. Reverse polarity connection will
damage LED boards and void warranty.
1. Remove the lens by placing an appropriate sized flat head screw driver into the snap lock clips and pushing the clips
slightly in and down until they release the lens. This must be completed to each of the four clips (Figure 1).
2. Pull the lens away from the unit. The internal reflector and chassis can now be removed by placing the screw driver
into the reflector locking channels and twisting slightly until the clip releases. This must be completed to each of the
four mounting channels (Figure 2). For recessed installation see (Figure 3)
3. Pull the reflector and chassis away from the back plate.
4. Bring the DC wires into the housing through the top or back knockout hole using a matched conduit fitting (supplied by
others).
5. Surface, wall or ceiling installation can be completed by installing screws and washers (supplied by others) with a
waterproof cap through the back of the fixture housing (Figure 4).
6. Connect 12V or 24 VDC to yellow (positive +) and to purple (negative - ).
7. Re-align the reflector with the back plate and push together until each locking clip engages (Figure 5).
8. Align the lens with the unit and push in back into place until each lens snap lock clip engages.
WALL MOUNTING
Fixture is shipped with LED strips positioned for ceiling mounting. To improve light distribution for wall mounting
(Figure 10) configure unit as follows:
1. Test switch holes indicates bottom of fixture (Figure 6)
2. Ensure locating pin goes through slot in LED strip (Figure 7)
3. Un-snap bottom LED strip and gently snap into middle notch and lower notch (Figure 8)
4. Un-snap top LED strip and gently snap into lower notch and upper notch (Figure 10)
MAINTENANCE
1. The equipment is to be repaired whenever the equipment fails to operate as intended during the duration test. Written records of test results and any repairs made must be maintained. Beghelli Inc. strongly recommends
compliance with all Code requirements.
2. Clean lens on a regular basis.
NOTE: The servicing of any parts should be performed by qualified service personnel only. The use of replacement parts
not furnished by Beghelli Canada Inc., may cause equipment failure and will void the warranty.
The LEDs listed herein when used according to the instructions with this unit are in accordance with the requirements of
CSA Standard C22.2, No. 141 – Unit Equipment for Emergency Lighting.
Beghelli Canada Inc., 3900 14th Avenue, Markham, ON L3R 4R3 Tel: (905) 948-9500 Fax: (905) 948-8673
926000332
05/13/2014
4
4
3
3
2
2
Figure 1
4
1
1
Figure 2
D
D
D
D
releasereflector
reflector
release
releaselens
lens
release
D
release len
B
C
C
C
C
emergency version
Figure 3
Figure 4
Back box
Screws & washers
not supplied
Securing Strap
B
B
Figure 5
B
B
C
Waterproof
cap
emergency version
version
emergency
remoteversion
version
remote
A
Tempesta
Ceiling Mount
This document is the property of and contains information proprietary to Beghelli Canada, Inc. It is submitted in confidence and is to be used solely for the
purpose
for which
was furnished
returned
upon request.
This document
such information
is not toin
be
reproduced,
transmitted,
disclosed,
used
This
document
is theitproperty
of andand
contains
information
proprietary
to Beghelliand
Canada,
Inc. It is submitted
confidence
and
is to be used
solely fororthe
acceptance
ofreproduced,
this document
shall be considered
otherwise
whole
or infurnished
part without
authorization
of Beghelli
Canda, Inc.
The
recepient's
purpose
for in
which
it was
andprior
returned
upon request.
This document
and
such
information
is not to be
transmitted,
disclosed, an
or used
agreement
to theorforegoing.
otherwise
in whole
in part without prior authorization of Beghelli Canda, Inc. The recepient's acceptance of this document shall be considered an
agreement to the foregoing.
PART NAME
Tempesta LED instruction sheet
PART NAME
drawing LED instruction sheet
Tempesta
drawing
A
A
wall mount
mount
wall
4
4
ceilingmount
mount
ceiling
3
3
PART #
PART #
2
2
UNLESS OTHERWISE SPECIFIED
ALL DIMENSIONS
INCHES
UNLESS
OTHERWISE=SPECIFIED
ALL
DIMENSIONS
ANGLES
+ 1/2 = INCHES
ANGLES + 1/2
TOLERANCES:
.X =  .020
TOLERANCES:
.010
.XX= =.020
.X
.005
.XXX= =.010
.XX
.003
.XXXX
.XXX
= =.005
.XXXX =  .003
3900 14Th. Avenue
MATERIAL
Markham
Ontario, L3R 4R3
3900
14Th. Avenue
Tel. # 905Ontario,
948-9500
Fax
# 905 948 8673 MATERIAL
Markham
L3R
4R3
email:
sales@beghellicanada.com
Tel.
# 905
948-9500 Fax # 905 948 8673
FINISH
Web:sales@beghellicanada.com
http://www.beghelli.com
email:
FINISH
Web: http://www.beghelli.com
DATE
DRAWN BY
DWG NO
L D BY
DATE 10/24/2013
DRAWN
DWG NO
LD
SIZE
SIZE
wall mount
10/24/2013
REF NO
SCALE
SCALE DO NOT SCALE REF NO
DO NOT SCALE
A
A
ceiling mount
REV
REV
PAR
SHEET
SHEET
1
1
4
3
Recess Trim Plate
B
Figure 6
Figure 7
Figure 8
Figure 10
Figure 9
Wall Mount
Test Switch
Holes
Locating Pin
Lower
Notch
Middle
Notch
Bottom Board
Lower
Notch
Upper
Notch
A
Top Board
wall mount
4
TROUBLESHOOTING
LED STRIPS DO NOT COME ON AT ALL IN EMERGENCY MODE
1. Either the output of battery unit equipment is shorted or the DC lead wires are not connected.
2. Check and ensure:
DC polarity is correct at both yellow (+) and purple (–) wires
If polarity is connected wrong, LED boards need to be replaced.
SAVE THESE INSTRUCTIONS
Beghelli Canada Inc., 3900 14th Avenue, Markham, ON L3R 4R3 Tel: (905) 948-9500 Fax: (905) 948-8673
926000332
05/13/2014