926000292
ILLUMINA BS100LED
®
INDUSTRIAL
VAPOR TIGHT
INSTALLATION INSTRUCTIONS
Beghelli Canada
3900 14th Avenue
Markham, Ontario L3R 4R3 Canada
P: (905) 948-9500
F: (905) 948-8673
www.BeghelliCanada.com
Beghelli USA
3250 Corporate Way
Miramar, Florida 33025 USA
P: 800 726 4316 / P: 954 442 6600
F: 954 442 6677
www.BeghelliUSA.com
Beghelli Mexico
Av El Marques No. 70, Interior 4
76246 Mpio. El Marquez
Queretano, QRO. Mexico
P: +52 442-221-6439 / F: +52 442-221-6215
www.BeghelliMexico.com
BS100LED
INSTALLATION INSTRUCTIONS
I L L U M I N A
®
BS100led
I N D U S T R I A L
30W, 48W & 70W MODEL
120V to 277V or 347V INPUT
HT & SA
4ft Length
LENS/DIFFUSER
LED STRIP
EACH MODEL NUMBER CONSISTS OF THE FOLLOWING:
SERIES / OPERATION / LED COLOR TEMP. / INPUT
REFLECTOR
Series:
Operation:
BS100LED
HT & SA
LED / COLOR- WT35 (3500K)
TEMP.: WT40 (4000K)
WT57 (5700K)
LENS CLIP ( 8 TOTAL)
FIXTURE HOUSING
CONDUIT KNOCKOUTS
(BOTH ENDS)
Input: 120V to 277V or 347v INPUT
IMPORTANT SAFEGUARDS
When using electrical equipment, basic safety precautions should always be followed including the
following:
READ AND FOLLOW ALL SAFETY INSTRUCTIONS.
1. Do not let power cords touch hot surfaces.
2. Do not mount near gas or electric heaters.
3. Always mount equipment in a location that is not subjected to tampering by unauthorized personnel.
4. The use of accessory equipment not recommended by Beghelli, may cause an unsafe condition, and will void the warranty.
5. Do not use this equipment other than its intended purpose.
6. Servicing of this equipment should be performed by qualified service personnel.
SAVE THESE INSTRUCTIONS!
BS100LED
TYPICAL INSTALLATION
FIRST MAKE SURE POWER IS TURNED OFF!
No user serviceable parts. Refer service to a qualified service
1. Remove diffuser / lens.
technician. Read instructions prior to installing and/or operating
this device. Installation should be performed by a licensed
2. Remove the reflector and mounting hardware bag.
electrician/installer in accordance with local codes.
3. Install conduit fitting.
4. Securely mount the fixture hardware provided. The fixture can be snapped onto the hardware as illustrated.
5. Prepare fixture for wiring / hang reflector from internal clips.
6. Connect AC supply and ground as labeled on the provided wire leads. CAP unused wire! CAUTION! Failure to CAP unused wire may result in a shock hazard or unsafe condition as well as equipment failure. Route wires and secure them in place.
IMPORTANT: For the BS100LED “SA” DO NOT JOIN CONVERTER CONNECTOR UNTIL INSTALLATION IS COMPLETE AND AC POWER IS SUPPLIED TO THE EMERGENCY DRIVER. SA option must specify 120V or 277V.
7. Insert LED reflector.
8. Ensure the reflector lip engages the tab channels on the housing before snapping the reflector in position.
9. Install diffuser clips. Reposition the diffuser/lens and snap each of the eight (8) clips into place
(a “clack” sound is made).
10. Turn on AC.
SAVE THESE INSTRUCTIONS!
BS100LED
TYPICAL INSTALLTION
1. REMOVE DIFFUSER / LENS
2. REMOVE LED REFLECTOR FROM HOUSING
3. EXTRACT MOUNTING HARDWARE,
INSTALL CONDUIT FITTING (included)
4. CONNECT TO POWER
G
N
OM
FR N AC L
I
MA
5. INSTALL LED REFLECTOR 6. INSTALL DIFFUSER CLIPS
7. INSTALL DIFFUSER/LENS
Labeled wire leads are provided for
Line / Hot, Neutral / Common and
Ground.
Labels will indicate the rated input
voltage: 120V TO 277V or 347V 60Hz.
Exact POWER SUPPLY and wiring
configuration may differ from image
above: FOLLOW ACTUAL WIRE LABELS.
8. SECURE DIFFUSER/LENS WITH CLIPS
BS100LED
MOUNTING
DIMENSIONS
26.00”
50.75”
STAINLESS STEEL
MOUNTING PLATE
1/2” IP CONdUIT
KNOCKOUT
1.825”
0.50”
3.70”
.250”
4.20”
.554”
.630”
INSTALL MOUNTING HARDWARE
SURFACE MOUNT
CHAIN HANG MOUNT (CH)
WALL MOUNT
FIXTURE REMOVAL (IF NECESARY)
SINGLE PENdANT MOUNT (SPK)
BS100LED
MOUNTING OPTIONS
AIRCRAFT CABLE MOUNTING
FEEd SUSPENSION
CANOPY KIT
DOUBLE PENDANT MOUNTING
NON FEEd SUSPENSION
CANOPY KIT
FEEd SUSPENSION
CANOPY KIT
NON FEEd SUSPENSION
CANOPY KIT
J-BOX
J-BOX
CROSS BAR
CROSS BAR
CANOPY
(screws not included)
LOCK NUT
(for double lock
on stem)
(2) SCREWS IN J-BOX
(screws not included)
CANOPY
CABLE GRIPPER
SLIP RING
(TO POSITION
CANOPY)
SET SCREW
FOR SLIP RING
WIRE TIES
STEM (1/4” IPS)
AIRCRAFT CABLE
POWER CORd
WIRE TIES
POWER CORd
STAINLESS STEEL
MOUNTING PLATE
STAINLESS STEEL
MOUNTING PLATE
LOCK NUT
LOCK NUT
BS100LED
TRUNION MOUNT (TM)
MOUNTING OPTIONS
PIVOT MOUNT (PM)
Magnetic Mount (MM)
1/4-20 NUTS
MOUNTING CLIP
AS SUPPLIED WITH
FIXTURE
MAGNET
1/4-20 SCREW
JUNCTION MOUNT (JM)
DIMMING WIRING DIAGRAM
Purple(+)
Gray(-)
Main AC
Main AC
DIMMING
0-10V WALL DIMMER
For dimmer switch wiring details, please refer
to dimmer manufacturer’s installation guide.
(Dimmer not supplied by Beghelli)
NOTE: WIRE LOCATIONS WILL VARY. REFERENCE WIRES BY
COLOUR NOT LOCATION
Beghelli Canada
3900 14th Avenue
Markham, Ontario L3R 4R3 Canada
P: (905) 948-9500
F: (905) 948-8673
www.BeghelliCanada.com
Beghelli USA
3250 Corporate Way
Miramar, Florida 33025 USA
P: 800 726 4316 / P: 954 442 6600
F: 954 442 6677
www.BeghelliUSA.com
Beghelli Mexico
Av El Marques No. 70, Interior 4
76246 Mpio. El Marquez
Queretano, QRO. Mexico
P: +52 442-221-6439 / F: +52 442-221-6215
www.BeghelliMexico.com