Catalog
Number
Notes
FEATURES & SPECIFICATIONS
INTENDED USE — Architectural deep-cast luminaire provides general illumination for exterior or interior
applications. Ideal for rough service (vandal resistant) applications where safety and security are a concern.
Designed to complement building architecture and to endure extreme environmental conditions and physical
abuse. Certain airborne contaminants can diminish integrity of acrylic. Click here for Acrylic Environmental Compatibility table for suitable uses.
CONSTRUCTION — Bezel one-piece, marine-grade die-cast aluminum, low copper alloy (<1% copper),
.125" (1/8") thick. Encloses lens and secures to housing with stainless steel Torx® T-10 set screws (see Options).
Housing: One-piece, marine-grade die-cast aluminum, low copper alloy (<1% copper), with post-painted
polyester powder coat finish. Four-hole mounting detail for use directly over outlet box, or conduit entry
through three 1/2" threaded openings on side or 3/4" threaded opening on rear surface.
Gasket: Polycarbonate: Perimeter lens gasket is one-piece silicone "O" ring. Glass: Perimeter lens gasket is
closed-cell silicone. Pad mounting is closed-cell neoprene that seals housing to mounting surface. Gaskets
help cushion impact shock.
Finish: Standard finish is textured polyester powder coat in white, black or bronze. Optional architectural
colors are available (see Options).
OPTICS — Lens-polycarbonate: Translucent white, injection-molded, UV-stabilized lens is .125" (1/8") thick.
Smooth exterior allows for easy cleaning, and interior pattern diffuses light for even surface illumination.
Lens-glass: Tempered borosilicate lens, .250" (1/4") thick, has smooth exterior for easy cleaning and textured
interior.
Reflector: Internal reflector is semi-specular aluminum, with high-reactance white powder coat perimeter
for maximum light output. Lamp positioning assures uniform brightness and illumination.
ELECTRICAL — Socket: High-temperature thermoplastic with lamp retention clip.
Lamp: maximum wattage lamp 100W. Provided by others.
INSTALLATION — Unit may be ceiling or wall mounted.
LISTINGS — UL listed to US and Canadian standards (See Options). UL listed for 25oC ambient and wet locations. IP65 rated.
WARRANTY — 1-year limited warranty. Complete warranty terms located at
www.acuitybrands.com/CustomerResources/Terms_and_conditions.aspx
Rough Service products by Lithonia Lighting are engineered to withstand extreme physical assault. When
properly installed per instructions for maximum vandal resistance, any Rough Service lighting fixture
utilizing a polycarbonate lens and/or polycarbonate housing enclosure that is rendered inoperable as a result
of physical abuse, will be repaired or replaced without charge for the life of the product.
Type
Rough Service Fixture
VGR5C
INCANDESCENT
Round Double Grille
Deep Housing
Ceiling/Wall Mounted
All dimensions are shown in inches (centimeters)
unless otherwise specified.
13-3/4
(34.9)
Note: Specifications subject to change without notice.
6-7/8
(17.5)
Actual performance may differ as a result of end-user environment and application.
ORDERING INFORMATION
Lead times will vary depending on options selected. Consult with your sales representative.
Example: VGR5C DWHG
VGR5C
Series
VGR5C
Lens
(blank) Polycarbonate
GL
Borosilicate glass
Paint finishes1
Standard textured finishes
DWHG White
DBLB Black
DDBT Dark bronze
DNAT Natural aluminum
DSST
Sandstone
Optional textured finishes
DBNH Bronze
DSPD Dark gray
DSPE
Green
DSPF
Rust
DSPG Dark red
DSPH Light red
DSPJ
Light gray
Accessories: Order as separate catalog number.
RK1 T10DRV
RK1 T20BIT
RK1 T20DRV
VGRDS XXXX
Torx TX10 screwdriver, for use with Gateway set screws.
Hex-base driver bit, Torx TX20, for tamper-resistant screws with center reject pin.
Torx TX20 screwdriver for use with tamper-resistant screws with center reject pin.
Decorative shroud5
Options
Shipped installed in fixture
EC
Emergency circuit (incandecsent - 25W max.; DC bayonet base)2
NL
Night-light (Incandescent - 6W max.; 656 DC base)2
TRS
Tamper-resistant screws3
VGRDS Decorative shroud4
CSA
Listed and labeled to comply with Canadian safety standard
Notes:
1.
For additional paint colors, refer to See www.lithonia.com/archcolors or
Architectural Paint brochure.
2.
Maximum wattage lamp provided
3.
T-20 screws with center reject pin.
4.
Color will be the same as the bezel.
5.
Must specify color (Example: VGRDS DWHG).
INDUSTRIALVGR5CI
VGR5C Rough Service Ceiling or Wall-Mounted Fixture, Incandescent
VGR5CI
INDUSTRIAL: One Lithonia Way Conyers, GA 30012 Phone: 800.315.4963 Fax: 770-981-8191 www.lithonia.com
© 2012 Acuity Brands Lighting, Inc. All rights reserved. Rev. 05/29/12