Catalog
Number
FEATURES & SPECIFICATIONS
Notes
INTENDED USE — Architectural deep-cast luminaire provides general illumination for rough service
(vandal-resistant) applications. Ideal for interior or exterior applications where safety and security are a
concern. Designed to complement building architecture and to endure extreme environmental conditions
and physical abuse. Certain airborne contaminants can diminish integrity of acrylic. Click here for
Acrylic Environmental Compatibility table for suitable uses.
CONSTRUCTION — Bezel one-piece, marine-grade die-cast aluminum, low copper alloy (<1% copper),
.125" (1/8") thick. Encloses lens and secures to housing with stainless steel Torx® T-10 set screws (see Options).
Housing: One-piece, marine-grade die-cast aluminum, low copper alloy (<1% copper), with post-painted
polyester powder coat finish. Four-hole mounting detail for use directly over outlet box, or conduit entry
through three 1/2" threaded openings on side or 3/4" threaded opening on rear surface.
Gasket: Polycarbonate: Perimeter lens gasket is one-piece silicone "O" ring. Glass: Perimeter lens gasket is
closed-cell silicone. Pad mounting is closed-cell neoprene that seals housing to mounting surface. Gaskets
help cushion impact shock.
Finish: Standard finish is textured polyester powder coat in white, black or bronze. Optional architectural
colors are available (see Options).
OPTICS — Lens-polycarbonate: Translucent white, injection-molded, UV-stabilized lens is .125" (1/8") thick.
Smooth exterior allows for easy cleaning, and interior pattern diffuses light for even surface illumination.
Lens-glass: Tempered borosilicate lens, .250" (1/4") thick, has smooth exterior for easy cleaning and textured
interior.
Reflector: Internal reflector is semi-specular aluminum, with high-reactance white powder coat perimeter
for maximum light output. Lamp positioning assures uniform brightness and illumination.
ELECTRICAL — Socket: High-temperature thermoplastic lamp with retention clip.
Lamp: maximum wattage lamp 100W. Provided by others.
INSTALLATION — Unit may be ceiling- or wall-mounted..
LISTINGS — UL Listed to U.S. and Canadian safety standards (see Options). UL listed for 25°C ambient and
wet locations. IP65 rated.
WARRANTY — 1-year limited warranty. Complete warranty terms located at
www.acuitybrands.com/CustomerResources/Terms_and_conditions.aspx
Type
Rough Service Fixture
VGR1C
INCANDESCENT
Round Open Face
Deep Housing
Ceiling/Wall Mounted
Rough Service products by Lithonia Lighting are engineered to withstand extreme physical assault. When
properly installed per instructions for maximum vandal resistance, any Rough Service lighting fixture
utilizing a polycarbonate lens and/or polycarbonate housing enclosure that is rendered inoperable as a result
of physical abuse, will be repaired or replaced without charge for the life of the product.
All dimensions are shown in inches (centimeters)
unless otherwise specified.
13-3/4
(34.9)
6-3/4
(17.1)
Note: Specifications subject to change without notice.
Actual performance may differ as a result of end-user environment and application.
ORDERING INFORMATION
Lead times will vary depending on options selected. Consult with your sales representative.
Example: VGR1C DWHG
VGR1C
Series
VGR1C
Lens
(blank) Polycarbonate
GL
Borosilicate glass
Paint finishes1
Standard textured finishes
DWHG White
DBLB Black
DDBT Dark bronze
DNAT Natural aluminum
DSST
Sandstone
Optional textured finishes
DBNH Bronze
DSPD Dark Gray
DSPE
Green
DSPF
Rust
DSPG Dark Red
DSPH Light Red
DSPJ
Light Gray
Accessories: Order as separate catalog number.
RK1 T10DRV
RK1 T20BIT
RK1 T20DRV
VGRDS XXXX
INDUSTRIAL
Torx TX10 screwdriver, for use with Gateway set screws.
Hex-base driver bit, Torx TX20, for tamper-resistant screws with center reject pin.
Torx TX20 screwdriver for use with tamper-resistant screws with center reject pin.
Decorative shroud5
Options
Shipped installed in fixture
EC
Emergency circuit (Incandecsent - 25W)2
NL
Night-light (Incandescent - 6W max., 656DC base)2
TRS
Tamper-resistant screws3
VGRDS Decorative shroud4
CSA
Listed and labeled to comply with Canadian safety standards
Notes:
1.
For additional paint colors, refer to See www.lithonia.com/archcolors
or Architectural Paint brochure.
2.
Maximum wattage lamp provided
3.
T-20 screws with center reject pin.
4.
Color will be the same as the bezel.
5.
Must specify color (Example: VGRDS DWHG).
VGR1CI
VGR1C Rough Service Wall/Ceiling-Mounted Fixture, Incandescent
INDUSTRIAL:
One Lithonia Way Conyers, GA 30012
Phone: 800-315-4963 Fax: 770-981-8191
VGR1CI
www.lithonia.com
© 2012 Acuity Brands Lighting, Inc.
All rights reserved. Rev. 05/29/12