GNDC 1700V Dual IGBT Gate Driver

advertisement
GNDC
1700V Dual IGBT Gate Driver
Features :
z
z
z
z
z
z
z
z
z
Typical applications :
Dual driver circuit for half-bridge IGBT modules
z Driver for IGBT modules in bridge circuits,
Suitable for parallel IGBT modules
choppers, inverter drivers and SMPS.
CMOS compatible input buffer
z High power UPS
Short circuit protection by Vce monitoring
z DC bus voltage up to 1200V
Error latch output
Internal isolated power supply
Short pulse suppression (Switching pulse shorter than 500nS is suppressed)
Supply undervoltage monitoring ( <13.5V )
Interlock function selectable by jumper
Absolute Maximum Ratings :
Symbol
Parameter
Values
Units
18
V
Vs+0.3
V
Output peak current
±24
A
Output average current (max; Tamb=25°C)
130
mA
fmax
Switching frequency (max)
20
kHz
VCE
Collector emitter voltage
1700
V
dv/dt
Max. rate of rise and fall of voltage (Secondary to primary
side)
75
kV/uS
Visol
Isolation test volt. Input-Output (1min.)
4000
V
Qout_pulse
Max. rating for output charge per pulse
±10
uC
Vs
Supply voltage primary side
ViH
Input signal voltage high
Iout_peak
Iout_av_max
Top
Operating temperature
-25…+85
°C
Tstg
Storage temperature
-25…+85
°C
PIN Array :
Figure1 : Dimensions and connections of 1700V IGBT Driver
Driver board output capability :
Qg/f
Qg(uC)
15
10
5
0
1
3
5
7
9
11
13
15
17
19
f(kHz)
Figure1:Output charge
per pulse V.S frequency
Primary side pin array : (X1 14Pin DIN 41651)
PIN No.
Designation
Explanation
2
BOT
Input signal bottom switch
3
ERROR
Error out
4
TOP
Input signal top switch
8,9
Vs
Supply power , 15V
10,11
GND
Ground , 0V
Secondary side pin array : (JTOP and JBOT )
PIN No.
Designation
Explanation
1
E
Emitter output (JBOT bottom switch , JTOP top switch)
2
G
Gate output (JBOT bottom switch , JTOP top switch)
5
C
Collector output (JBOT bottom switch , TOP top switch)
Technical explanations :
a. Input signal:
Input signals are CMOS compatible. Positive logic (High = IGBT on). The signal at X1.4 is for
top IGBT and X1.2 is for bottom IGBT.
b. Short circuit protection:
Short circuit protection is provided by measuring the collector-emitter voltage. In the case of a
short circuit, the IGBT is turned off immediately. An error memory prevents the IGBT from being
turned on again.
X1.3 is for short circuit indication. It is an open collector output. LOW = NO ERROR.
The ERROR signal may be disabled either by delivering zero to both signal inputs (RESET) or
by switching the power supply off. The RESET signal width must be more than 9uS long.
Figure 2: Driver status information ERROR and RESET
c. Output gate resistors Rgon, Rgoff:
These resistors are responsible for the switching speed of each IGBT. The final value depends
on different application. Please refer to Figure 1 to install the resistors.
Electrical Characteristics :
Symbol
Values
Parameter
Units
min.
Typ.
max.
14.4
15
15.6
V
Vs
Supply voltage primary sides
Iso
Supply current primary side (no load)
-
140
-
mA
Is
Supply current primary side operation
-
-
850
mA
Vuvp
Supply under voltage protection
-
13
-
V
VIT+
Logic input threshold voltage (High)
12.9
-
-
V
VIT-
Logic input threshold voltage (Low)
-
-
2.1
V
Rin
Input resistance
-
47
-
KΩ
Vg(on)
Output turn on gate voltage
-
+15
-
V
Vg(off)
Output turn off gate voltage
-
-7.5
-
V
td(on)IO
Input-output turn-on propagation time
-
540
-
nS
td(off)IO
Input-output turn-off propagation time
-
580
-
nS
td(err)IO
Error Input-output propagation time
Vce(sat)
Reference voltage for Vce monitoring
Cps
Coupling capacitance primary-secondary
W
Weight
HxWxL
Dimensions
350
-
nS
-
7.8
V
22
-
pF
102
g
32 x 90.8 x 97
mm
GNDC CO.,LTD
Taipei Headquarters
Qingdao Subsidiary
Beijing Office
Suzhou Office
8F-1,No.192,Rueiguang Road,Neihu,
Np.192,Zhuzhou Road,Hi-Tech
Room 1604,Building 5,FortuneCentre,
Room 655,West Building,Huihao
Taipei,11491,Taiwan
ParkQingdao 266101,PR China
15 Da Liu Shu,Haidian District,Beijing
intermational,No.58,Shishan Road,
100081,PR China
New District,Suzhou 215011,PR China
Tel:+886-2-2799 6010
Tel:+86-532-8870 1773
Fax:+886-2-2799 6035
Fax:+86-532-8870 1478
Tel:+86-10-6214 0376
Tel:+86-512-6807 0775
http://www.gndc-ups.com
http://www.gndc-ups.com
Fax:+86-10-6214 0377
Fax:+86-512-6807 0776
E-mail:gsales@gndc-ups.com
E-mail:sales@semcor.com.cn
E-mail:Beijing@semcor.com.cn
E-mail:suzhou@semcor.com.cn
Download