Product catalogue
Lighting and Room Control
Edition 2009
This catalogue © Infranet Partners Ltd 2009. All Rights Reserved.
No part of this publication may be reproduced or published in any form, whether physical or
electronic, without the written permission of the copyright owner.
The information contained in this catalogue is believed to be correct at the time of compilation
(April 2009). Due to our programme of continuous product improvement, certain product
specifications may be liable to change during the duration of this catalogue. Customers should
therefore check current product specifications with their local Infranet Partners sales office before
ordering. Neither Infranet Partners Limited or its sales distributors (as listed on the back cover)
shall be liable for any loss damage or tort caused by changes to product specifications or product
availability, nor for any errors in, or omissions from any information contained in this publication.
E. & O.E.
Infranet Partners and the Ellipse logo are trademarks of Infranet Partners limited and are used with
permission.
Echelon, LonWorks®, LNS® are registered trademarks of Echelon Corporation. LonMark® is a
registered trademark of LonMark International. All other trademarks referenced in the document
are the property of their respective trademark owners.
2
Catalogue content
This catalogue has been arranged to give you an overview of Infranet Partners
wide range of solutions based on open standards for lighting and room control.
Product information
Our complete range of lighting and room control products is shown here in detail.
Each product page features a short description, together with key features and
specifications, as well as a product picture and a typical wiring diagram. Symbols
highlight the key features of each product and guide you through the catalogue
quickly and simply. All prices shown are list prices.
If you need further information, please visit our website or contact one of our
local sales offices for help and advice.
Content
InfraDALI Series
InfraLIGHT 100 Series
InfraLIGHT Modular 200 Series
InfraLIGHT Manager
InfraLIGHT BACnet Gateway
InfraLIGHT Lighting scene panel
InfraLIGHT LED Driver
4-6
7-9
10-12
13
14
15
16
InfraSENSE Lighting sensors
17-21
InfraTROL 100 Series
InfraTROL 580 Series
InfraSCENE
22-24
25-26
27
„Fast Connect“ Modular wiring
Power and Dimming Lighting Connectors
InfraDALI Easy installation
28
29
33
STRATOSPHERE
InfraZONE
InfraLIGHT Designer
30
31
32
L-IP Routers
L-Switch
NIC
L-INX
34
35
36
37
Terms and condition
39
3
InfraDALI 100
The InfraDALI 100 is a Light controller for 16 LonMark Lamp Actuator Objects
(LAO) with feedback for 64 DALI ballasts (DB). The controller can be configured
to access all DALI lamps, 16 groups or single lamps.
16 groups is the maximum that can be controlled as DALI groups. Each LAO
can be configured to report alarms or service messages about defective ballasts,
lamps or communication errors in nvoAlarm2 of the node object.
- 64 DALI ballasts with alarming on a lamp by lamp base
- network interface offering control for 16 Lamp Actuator Objects #3040
each representing a DALI group
- 1 Scene controller object
- 8 digital inputs for local control or 4 switch objects #3200
The Neuron based controller supports the installation via LNS Plug-in or via predefined replace taster on input 2.
The InfraDALI 100 is a group lamp actuator to control lamps in an open loop
or in conjunction with InfraSENSE 400 to provide constant-light control and
occupancy-controlled lighting applications.
Specification
InfraDALI 100
Network options
FTT-10, up to 2.7 km bus, up to 450 m free topology
DIN
FTT DALI 230V
DALI, up to 300 m max. distance between the ballasts and InfraDALI
Power supply
230V / 50 Hz / DALI supply integrated
Power consumption
5W
uP
Neuron 3150 / DALI coprocessor
Digital Input
8 potential free contacts for SELV (Safe Extra Low Voltage)
Housing
M36 for DIN-rail mounting (EN500022); Dimensions 157 x 86 x 60 i.e. 9 TE
Environmental requirements
Operating temperature: 0°C to +70°C , Storage temperature: -50°C to +95°C, Max. air humidity: 90%, not condensing
EMC / CE
EN60950
Certifications
LonMark V 3.3
Order Code
Type
Description
410070U
InfraDALI100
LonWorks Controller for DALI lighting solutions
4
InfraDALI 1000
The InfraDALI 1000 is a controller for 80 Lamp Actuators with feedback for 64
DALI Ballasts (DB), 16 Lamp Actuator Groups, 64 Lamp Actuators for one single
ballast each. Each Lamp Actuator Object can be configured for to report alarms or
service messages about defective lamps or communications errors in nvoAlarm2
of the node object.
The Neuron based controller supports the installation of the DALI system via
LNS Plug-In, on device webpage, wireless device or preconfigured replace button.
The InfraDALI 1000 is a fully featured Lamp Actuator for groups and single
lamps to control lamps in an open loop or in conjunction with InfraSENSE 400
to provide constant-light control and occupancy-controlled lighting applications.
- 64 DALI ballasts with alarming on a lamp-by-lamp base
- 8 digital Inputs for local control. Able to connect to other InfraDALI
controllers.
- Supports the installation of the DALI system via LNS-Plug-In, on device
webpage, wireless device or preconfigured replace button.
- Address assignement of all recognized devices (randomize).
- Assign / change address on specific modules; provide group allocation
(16 groups)
- Set fade time
- Supports DALI2, IEC 62386
- Set the minimum / maximum value, condition after failure message, condition
after starting „wink“ of all lamps, single group or single lamp.
- Lamp feedback to nvo Alarm
- Lamp feedback to nvoBallast state (display group failures).
Specification
InfraDALI 1000
Network options
FTT-10, up to 2.7 km bus, up to 450 m free topology / Ethernet: IP-852, Webserver
DIN
IP
FTT DALI 230V
DALI, up to 300 m max. distance between the ballasts and InfraDALI
Power supply
230V / 50 Hz / DALI supply integrated
Power consumption
5W
uP
LC3020 / DALI coprocessor
Digital Input
8 potential free contacts for SELV (Safe Extra Low Voltage)
Housing
M36 for DIN-rail mounting (EN500022); Dimensions 157 x 86 x 60 i.e. 9 TE
Environmental requirements
Operating temperature: 0°C to +70°C , Storage temperature: -50°C to +95°C, Max. air humidity: 90%, not condensing
EMC / CE
EN60950
Certifications
LonMark V 3.3
DALI IEC 62380 Multimaster support
Order Code
Type
Description
411000K (FTT)
InfraDALI1000, FT-10
LonWorks Controller for DALI lighting solutions
411010Q (IP)
InfraDALI1000, IP-852
LonWorks Controller for DALI lighting solutions
5
InfraDALI 2000 Series - Flexible DALI lighting controllers
The InfraDALI 20XX is a line of fully featured Light controllers scalable for 8 / 16
/ 32 and 64 lamp actuators with feedback for 64 DALI ballasts.
The controller offers fully scalable objects for scene, constant light and lamp
actuator functionality.
InfraDALI20XX
- 64 ballasts with alarming on a lamp by lamp base
- 8 digital inputs / switch objects #3020 for the use of configurable digital
inputs
2008
2016
2032
2064
Lamp Actuators for groups #3040
8
16
16
16
Single lamp actuators #3040
8
16
32
64
Alarms
64
64
64
64
Constant light controllers #3070
8
16
32
64
8+1
16+1
32+1
64+1
Lamp burn in time for single lamps
8
16
32
64
Energy usage for single lamps
8
16
32
64
Each lamp actutator can be configured to report alarms or service messages about
defective ballasts, lamps or communication errors in nvoAlarm 2 of the node
object.
InfraDALI
This line offers an ideal approach to scale the installation cost according to
the physical requirements of a building. With the wide range of functionality
available, a system integrator can scale the same application to suit a specific
project or location.
Scene control #3251
Specifications
InfraDALI 2008, InfraDALI2016, InfraDALI2032, InfraDALI2064
Network options
FTT-10, up to 2.7 km bus, up to 450 m free topology / Ethernet: IP-852, Webserver
DIN
IP
FTT DALI 230V
DALI, up to 300 m max. distance between the ballasts and InfraDALI
Power supply
230V / 50 Hz / DALI supply integrated
Power consumption
5W
Isolation
Mains-low voltage 4 kV; mains-DALI 4 kV; DALI-low voltage 4 kV
uP
LC3020 / DALI coprocessor
Digital Input
Potential free contacts for SELV (Safe Extra Low Voltage)
Flammability
Self-extinguishing to UL 94-VO
Housing
M36 for DIN-rail mounting (EN500022); Dimensions 157 x 86 x 60 i.e. 9 TE
Environmental requirements
Operating temperature: 0°C to +70°C , Storage temperature: -50°C to +95°C, Max. air humidity: 100%, not condensing
EMC / CE
EN60950
Certifications
LonMark V 3.4
Order Code
Type
Description
412008Q (FTT/IP)
InfraDALI 2008
LonWorks Controller for DALI lighting solutions
412016H (FTT/IP)
InfraDALI2016
LonWorks Controller for DALI lighting solutions
412032S (FTT/IP)
InfraDALI2032
LonWorks Controller for DALI lighting solutions
412064W (FTT/IP)
InfraDALI2064
LonWorks Controller for DALI lighting solutions
6
InfraLIGHT 100
FROM 24V DC
POWER SUPPLY
0V DC
+24V DC
GND
LIGHTING
CIRCUIT 2
LIGHTING
CIRCUIT 1
CONTACTOR
+ 24V
OP 2
OP 1
GND
GND
CIRCUIT BREAKERS IN
DISTRIBUTION BOARD
LIGHTING
CIRCUIT 3
11
Service
Inf raLIGHT 100
E I A7 0 9 L i g h t i n g C on tr o ll e r
12
13
14
RELAY MODULE
4 Wa y x 1 0 A
See end plate for type/configuration
LO N
LO N
IP 7
IP 8
IP 6
IP 5
IP 4
+ 24V
GN D
Supply 24V DC
Channel FT/10
IP 3
IP 2
IP 1
See label for
Model and Version
FROM LAST LON DEVICE
ON/UP
ON/UP
ON/UP
ON/UP
LON
LON
LON
SW1
SW2
SW3
SW4
LON
TO NEXT LON DEVICE
OFF/DOWN
OFF/DOWN
OFF/DOWN
OFF/DOWN
· Modular clip-on relay for 4 or 8 channels of lighting
· Normally closed relay option
· 8 Switch objects #3200
· 5 Occupancy Controller Objects #3071
· 8 Lamp actuator objects #3040
· LonMark compliant.
· InfraLIGHT LNS plug-in available for easy configuration
· Standard M36 DIN-rail enclosure for easy fit into electrical panels
· CE, DEMKO approvals
The InfraLIGHT 100 range of lighting control modules provide a flexible solution to a wide range of lighting applications for efficiently managing your lighting
system.
Implementing standard LonMark® objects for Switch, Lamp Actuator, Occupancy
Control and Constant Light Control. The InfraLIGHT 100 can respond dynamically to ever-changing environmental conditions providing an efficient, effective
and satisfactory lighting solution.
In addition, flexible control can be achieved with the comprehensive Switch object. Supporting up to eight single-pole latching switches, toggle switches or four
double-pole retractive raise/lower switches allows a wide range of lighting requirements to be met at the touch of a button.
The InfraLIGHT 100 series comprises a base module plus a four or eight way
relay module. Used in conjunction with our InfraSENSE 200 multi-sensor providing occupancy and light level objects, a complete switched-circuit lighting control
solution can be realised.
Specifications
InfraLIGHT 100
Communications
LonWorks® FT-10 network interface
Power Supply
24V DC ± 20%
Operating Temperature
0 to 50 °C
Maximum Current
Controller Relaybox (8 relays)
Relaybox (4 relays)
100 mA
200 mA
100 mA
Switch Inputs
Input impedance
VIH / VIL > 5 KW / < 50 KW
> 6V / < 1V
Relays
230 V AC 10A (resistive), 6A (inductive)
EMC / CE
EN 61000-3-2, EN 61000-3-3, EN 50090-2-2, EN 50090-2-2/A1, EN 60950
Enclosure
M36 for DIN-rail mounting (EN500022)
Dimensions:
58 mm H x 86mm L x 70mm W
DIN
Order Code
Type
Description
410100L
InfraLIGHT 100
Switched lighting controller
201030W
RLY-4NO
Relay Box 4-way NO
201040C
RLY-8NO
Relay Box 8-way NO
201050H
RLY-8NC
Relay Box 8-way NC
104360K
PSU30
Power Supply 30 W
104300C
PSU60
Power Supply 60 W
FTT 24 V
7
InfraLIGHT 110
FROM 24V DC
POWER SUPPLY
0V DC
+24V DC
GND
LIGHTING
CIRCUIT 2
LIGHTING
CIRCUIT 1
CONTACTOR
+ 24V
OP 2
OP 1
GND
GND
CIRCUIT BREAKERS IN
DISTRIBUTION BOARD
LIGHTING
CIRCUIT 3
11
Service
Inf raLIGHT 100
Alternate connection to
Light Sensors
13
14
4 Wa y x 1 0 A
See end plate for type/configuration
LO N
LO N
IP 8
IP 7
IP 5
IP 6
IP 4
Supply 24V DC
Channel FT/10
IP 3
+ 24V
GN D
IP 2
See label for
Model and Version
Lux 2
IP 1
Lux 1
E I A7 0 9 L i g h t i n g C on tr o ll e r
12
RELAY MODULE
FROM LAST LON DEVICE
ON/UP
ON/UP
ON/UP
ON/UP
LON
LON
LON
SW1
SW2
SW3
SW4
LON
TO NEXT LON DEVICE
OFF/DOWN
OFF/DOWN
OFF/DOWN
- Normally closed relay option
- 4 Switch objects #3200
- 4 Light Sensor objects #1010
- 4 Constant Light Controller Objects #3050 (with Daylight link extensions)
- 4 Occupancy Controllers #3071
- 8 Lamp actuator objects #3040
- LonMark® compliant.
- Standard M36 DIN-rail enclosure for easy fit into electrical panels
- InfraLIGHT LNS plug-in available for easy configuration
- CE, DEMKO approvals
The InfraLIGHT 110 lighting control modules provides a flexible solution to a
wide range of lighting applications for efficiently managing the lighting system
employed for an office or factory workspace.
Implementing standard LonMark® objects for Switch, Lamp Actuator, Occupancy
Control and Constant Light Control and our unique light level sensor object. The
InfraLIGHT 110 can respond dynamically to ever-changing environmental conditions providing an efficient, effective and satisfactory lighting solution.
In addition to the comprehensive Switch Object, standard in the InfraLIGHT
100, the InfraLIGHT 110 inputs are universal, supporting both switches and
light level sensors. The InfraLIGHT 110 series comprises a base module plus a
four or eight way relay module.
Specifications
InfraLIGHT 110
Communications
LonWorks FT-10 network interface
Power Supply
24V DC ± 20%
Operating Temperature
0 to 50 °C
Maximum Current
Controller Relaybox (8 relays)
Relaybox (4 relays)
100 mA
200 mA
100 mA
Switch Inputs
Input impedance
VIH / VIL > 5 KW / < 50 KW
> 6V / < 1V
Relays
230 V AC 10A (resistive), 6A (inductive)
Enclosure
M36 for DIN-rail mounting (EN500022)
Dimensions:
58 mm H x 86mm L x 70mm W
DIN
®
Order Code
Type
Description
410110R
InfraLIGHT 110
Switched lighting controller
201030W
RLY-4NO
Relay Box 4-way NO
201040C
RLY-8NO
Relay Box 8-way NO
201050H
RLY-8NC
Relay Box 8-way NC
104360K
PSU30
Power Supply 30 W
104300C
PSU60
Power Supply 60 W
8
OFF/DOWN
FTT 24 V
InfraLIGHT 160
‘SELECTED SCENE’ INDICATORS
(OPTIONAL)
(SEE NOTE 1)
1
2
3
4
5
6
7
8
0V DC
+24V DC
GND
+ 24V
OP 5
OP 6
OP 7
OP 8
GN D
OP 1
OP 4
GN D
OP 2
OP 3
FROM 24V DC
POWER SUPPLY
Service
Inf raLIGHT 100
NOTE 1: ‘SELECTED SCENE’ INDICATORS TO BE EITHER:
E I A7 0 9 Li g h ti n g C on tr o ll e r
(a) 24V INCANDESCENT TELL-TALE INDICATOR LAMP, MAX. 1W (BRIGHT), 0.3W (DIM)
(b) STANDARD LED IN SERIES WITH 1K2 RESISTOR 0.5W (BRIGHT) OR 2K2 RESISTOR 0.4W (DIM)
LO N
LO N
IP 8
IP 7
IP 6
IP 5
IP 4
Supply 24V DC
Channel FT/10
IP 3
+ 24V
GN D
IP 2
IP 1
See label for
Model and Version
FROM LAST LON DEVICE
LON
LON
TO NEXT LON DEVICE
LON
LON
SCENE 1
SCENE 2
SCENE 3
SCENE 4
SCENE 5
SCENE 6
SCENE 7
SCNE 8
- Robust, proven controller
- Normally closed relay option
- 1 Scene Panel objects #3250
- 8 Scene Controller objects #3251
- LonMark® compliant.
- Standard M36 DIN-rail enclosure for easy fit into electrical panels
- InfraLIGHT LNS plug-in available for easy configuration
- CE, DEMKO approvals
The InfraLIGHT 160 lighting control module provides a flexible solution to
lighting scene management requirements in lecture theatres, meeting rooms,
conference halls and indeed any environment where its useful to have a number
of pre-defined light levels for each lighting group in your environment.
Implementing standard LonMark® objects for Scene Panel and Scene Controller,
the InfraLIGHT 160 can be pre-set with up to 8 unique light levels for each of
the 8 lighting groups (scene controllers). InfraLIGHT 160 provides an efficient, effective and satisfactory lighting solution in conjunction with standard wall
switch elements, thus ensuring compatibility to any décor scheme.
Each lighting scene can be easily recalled or new scenes learned through the
scene panel functionality, available through the eight switch inputs on the controller. The eight low-voltage outputs on the controller can be used to drive indicator lights to show current scene selection.
Specifications
InfraLIGHT 160
Communications
LonWorks FT-10 network interface
Power Supply
24V DC ± 20%
Operating Temperature
0 to 50 °C
Maximum Current
Controller Indicator Lamps
100 mA
330 mA (using 1W lamps)
100 mA (using 0.3W lamps)
Switch Inputs
Input impedance
VIH / VIL VIN max
> 5 KW / < 50 KW
> 6V / < 1V
V supply max
Enclosure
M36 for DIN-rail mounting (EN500022)
Dimensions:
58 mm H x 86mm L x 70mm W
Flammability:
Self-extinguishing to UL94-V0
DIN
FTT 24 V
®
Order Code
Type
Description
410160T
InfraLIGHT 160
Switched lighting controller
104360K
PSU30
Power Supply 30 W
104300C
PSU60
Power Supply 60 W
9
InfraLIGHT Modular 209 switched-circuit lighting controller
- Flexible, modular lighting controller with 9-way switched lighting outputs
- Modular ‘Fast Connect’ system for easy connection of sensors, switches
- Slim form factor for easy installation in ceiling or floor voids
- Supports a wide range of lighting control strategies
- Local or remote test of self-contained emergency lights
- InfraLIGHT LNS plug-in available for easy configuration
- LonWorks® FT-10 network interface for use as part of a building control
network.
InfraLIGHT Modular switched-circuit controllers provide a convenient and
economical means of lighting control with power distribution for lighting applications where dimming is not required, for example, corridors, utility areas,
washrooms, external lighting. The slim form factor (36 mm height) means that
the InfraLIGHT Modular range can be mounted into the shallowest of ceiling
or floor voids.
InfraLIGHT Modular controllers utilise Infranet Partners’ innovative ‘Fast Connect’ modular wiring system for presence, light level detectors and wall switches.
The built-in firmware supports a wide range of lighting control strategies based
on LonMark® objects, which can be easily configured using the InfraLIGHT LNS
plug-in.
InfraLIGHT 209 is currently available in two firmware builds. Order codes ending in -CL refer to lighting controls incorporating occupancy plus constant light
control. Order codes ending in -SC refer to lighting control incorporating occupancy plus scene control.
For installation accessories see page 28.
Specifications
InfraLIGHT 209
Communications
LonWorks® FT-10 network interface
Power Supply
230V AC 50Hz, 10W max. (excluding lighting loads).
Inputs
Sensor and up to four switch elements (configurable via plug-in or zone management tool)
Housing
Zinc-coated mild steel, powder coated
Dimensions
336 mm long x 248 mm wide x 38 mm deep (excluding connectors and mounting lugs), 275 mm wide including mounting lugs
Mains Input
GST Male connector, 3-pole, with locking tab
Lighting Outlets
Wieland GST female connector, 4-pole, with locking tab, (Switched Live, Neutral, Earth, Emergency Light Charger Live)
Sensor / switch
4 x RJ-12 Modular connectors, each supporting presence detector, light sensor and up to four switch elements
(configurable via plug-in)
Circuit protection
Lighting outlets: 2 x Fuse 6A (1 on 4-way version); Internal circuit: 1 x Fuse 250mA
Isolation
Mains – Low Voltage Signal: 4kV
EMC / CE
EN 60669-2-1: 2004
DIN
Order Code
Type
Description
414009D-CL
InfraLIGHT 209
9-way modular switched lighting controller
414009D-SC
InfraLIGHT 209
9-way modular switched lighting controller
10
FTT 24 V
InfraLIGHT Modular 229 lighting controllers with DSI Dimming
InfraLIGHT Modular 229 lighting controllers with DSI dimming provide a convenient and economical means of lighting control with power distribution for
general lighting applications such as offices and classrooms incorporating a dimming, constant-light or daylight-linking requirement.
- Flexible, modular lighting controllers with 9-way DSI lighting outputs
- Modular ‘Fast Connect’ system for easy connection of sensors, switches
- Slim form factor for easy installation in ceiling or floor voids
- Supports a wide range of lighting control strategies
- InfraLIGHT LNS plug-in available for easy configuration
- LonWorks® FT-10 network interface for use as part of a building control
network.
InfraLIGHT Modular 229 provides 9 lighting outlets, all with DSI dimming,
for applications where full dimming control is required, for example, an office,
classroom or meeting room where there is a requirement to dim the lights for
audio-visual presentation. The controller supports a wide range of lighting control strategies based on LonMark® objects, which can be easily configured using
the InfraLIGHT LNS plug-in.
InfraLIGHT 229 is currently available in two firmware builds. Order codes ending in -CL refer to lighting controls incorporating occupancy plus constant light
control. Order codes ending in -SC refer to lighting control incorporating occupancy plus scene control.
For installation accessories see page 28.
Specifications
InfraLIGHT Modular 229
Dimensions
350 mm long x 250 mm wide x 36 mm deep
Housing
Zinc-coated mild steel, powder coated
Power Supply
230V AC 50Hz, 20W max. (excluding lighting loads)
Mains Input
GST Male connector, 3-pole, with locking tab
Communications
LonWorks® FT-10 network interface
Lighting Outlets
GST female power connector, 4-pole, with locking tab (L, N, E, Em. Live)
BST female dimming signal connector, 2-pole (Dim-, Dim+)
Option
GST female connector, 6-pole, with locking tab (L, N, E, Em. Live, Dim-, Dim +)
Circuit protection
Lighting outlets: 2 x Fuse 6A; Internal circuit: 1 x Fuse 250mA
Sensor / switch inputs
4 x RJ-12 Modular connectors, each supporting presence detector, light
DIN
FTT 24 V
sensor and up to four switches (configurable via plug-in or zone management tool)
Isolation
Mains–Low voltage 4kV; Mains-DSI 2kV; DSI–Low voltage signal 3kV
Order Code
Type
Description
414900J-CL
InfraLIGHT 229
9-way DSI lighting controller, 4+2 pole lighting connectors
414900J-SC
InfraLIGHT 229
9-way DSI lighting controller, 4+2 pole lighting connectors
413900F-CL
InfraLIGHT 229
9-way DSI lighting controller, 6 pole lighting connectors
413900F-SC
InfraLIGHT 229
9-way DSI lighting controller, 6 pole lighting connectors
11
InfraLIGHT Modular 249 universal dimming controller
- Flexible, modular lighting controllers with 9-way lighting outputs
(Switched, Analog, DSI)
- One solution for a wide range of lighting needs
- Modular ‘Fast Connect’ system for easy connection of sensors, switches
- Slim form factor for easy installation in ceiling or floor voids
- Supports a wide range of lighting control strategies
- InfraLIGHT LNS plug-in available for easy configuration
- LonWorks® FT-10 network interface for use as part of a building control
network.
- Available with GST 6-pole connectors, or GST 4-pole power + BST 2-pole
dimming (option).
InfraLIGHT Modular 249 lighting controllers provide a ‘one for all’ solution
for general lighting control in offices, shops, hotels and other buildings where
there is a need for switched-circuit lighting control together with either analogue
(1..10V) or digital (DSI) dimming.
With 9 lighting outlets, these units provide a flexible solution for lighting control
with power distribution. By offering three control options in one controller, a
single device type can be specified to meet almost any internal lighting control
application where DALI is not required.
Each outlet supports switched-circuit control and either Analogue or DSI dimming, configurable via the InfraLIGHT plug-in.
InfraLIGHT 249 is currently available in two firmware builds. Order codes ending in -CL refer to lighting controls incorporating occupancy plus constant light
control. Order codes ending in -SC refer to lighting control incorporating occupancy plus scene control.
For installation accessories see page 28.
Specifications
InfraLIGHT Modular 240 Series
Dimensions
350 mm long x 250 mm wide x 36 mm deep
Housing
Zinc-coated mild steel, powder coated
Power Supply
230V AC 50Hz, 20W max. (excluding lighting loads)
Mains Input
GST Male connector, 3-pole, with locking tab
Communications
LonWorks® FT-10 network interface
Lighting Outlets
GST female power connector, 4-pole, with locking tab (Switch L, N, E, Em. Live)
BST female dimming signal connector, 2-pole (Dim-, Dim+)
Option
GST female connector, 6-pole, with locking tab (Sw. L, N, E, Em. Live, Dim-, Dim +)
Circuit protection
Lighting outlets: 2 x Fuse 6A (1 on 4-way version); Internal circuit: 1 x Fuse 250mA
Sensor / switch inputs
4 x RJ-12 Modular connectors, each supporting Presence detector, light
DIN
sensor and up to four switch elements (configurable via plug-in)
Isolation
Mains–Low Voltage: 4kV; Mains-Dim signal: 2kV; Dim signal–Low voltage: 3kV
Order Code
Type
Description
414999J-CL
InfraLIGHT 249
9-way lighting controller, 4+2 pole lighting connectors
414999J-SC
InfraLIGHT 249
9-way lighting controller, 4+2 pole lighting connectors
413999J-CL
InfraLIGHT 249
9-way lighting controller, 6 pole lighting connectors
413999J-SC
InfraLIGHT 249
9-way lighting controller, 6 pole lighting connectors
12
FTT 24 V
InfraLIGHT Manager
InfraLIGHT Manager is based on the advanced L-VIS display from Loytec, with
the addition of value-added applications which perfectly tailor the function of the
unit to the management of Infranet Partners lighting control systems.
-Control and display panel for ANSI/EIA-709 networks
-Graphical user interface with touch display
-Clear and user friendly navigation menus
-Representation of user defined graphics, numbers, text, bar charts,
trend logs, and bitmaps
-Visualization of individual data points (NVs)
-Control of individual data points (NVs)
-Alarming, alarm generator
-Access control with PIN code
-External temperature sensor (optional)
-Input for external light switch
-Simple, graphical programming with LNS Plug-In and dynamically
created network variables
-WYSIWYG preview on PC screen
-Up to 512 input or output network variables can be processed
-Up to 512 destination addresses can be used
InfraLIGHT Manager impresses by its timeless design, compatibility to both
modern and and traditional décor, as well as its extremely user friendly concept.
Any information can be shown in a pleasant style on the high resolution 320 x
240 color TFT touch display. The touch display offers easy navigation through the
menu structure but is also used to select lighting scenes, set temperatures, move
sun blinds, or send updates to network variables in the network. Network variables can be dynamically created using LNS 3.x based tools (e.g. NL-220, ALEX,
LonMaker® for Windows™, etc.).
The LNS plug-in supplied with the unit is used to quickly create the menu structure and design graphical pages which can be downloaded into InfraLIGHT
Manager via the network connection. The TFT touch display shows numbers, text,
bar charts, symbols, graphics, trend logs, and many other items in a clear way.
Specifications
InfraLIGHT Manager
Network ports
FT-10 and EIA-852 Ethernet (IP-852)
Input voltage
9-24V AC or DC
Power consumption
8 W typ
Display
High resolution 320 x 240 color LC touch display with backlight, 256 colors (VGA)
Applications
Compatible with LNS applications in the fast VNI™ mode, e. g. NL220®, ALEX, LonMaker™
Housing
High quality satin finish brushed stainless steel
Flush-mounting in combination with wall mounting box (included)
Dimensions
W = 210 mm, H = 165 mm, D = 60 mm
Environmental conditions
Operating range: 5°C...+50°C; Storage range: -10°C...+50°C; 10%-90% humidity non condensing
EMC / CE
EN 61000-3-2 / 3-3; EN 50090-2-2 / A1; EN 60950
FTT MOD 24 V
Order Code
Type
Description
407020N
InfraLIGHT Manager
Configurable TFT Touch Panel
13
InfraLIGHT BACnet Gateway
The LGATE-900 is a gateway which allows seamless integration of LonWorks and
BACnet networks by mapping LonWorks network variables (NVs) to standard
BACnet server objects. Each LGATE-900 can handle up to 750 BACnet Objects and
several devices can be installed in a network at the same time. L-Gate supports
management functions such as scheduling, alarming, and trending via corresponding BACnet objects.
Configuration is achieved with an easy-to-use LNS® plug-in or stand-alone configuration tool which allows browsing of the LNS® database.
Both static and dynamic Standard Network Variables (SNVTs) as well as User
Defined Network Variables (UNVTs) and Configuration Properties (SCPTs, UCPTs)
are supported. The configuration tool allows reading UNVTs from a device resource file and accessing Configuration Properties via LonMark file transfer. NVs
can be bound or used as “external data points”(polled), which are configured
with address information via the configuration tool.
- Maps EIA-709 network variables to BACnet server objects based on
CEN/TS 15231:2005
- Support of dynamically created network variables or static network variables
- Supports User Defined NVs (UNVTs) as well as Configuration Properties
(SCPTs, UCPTs)
- Initializes BACnet properties from SNVT description
- Supports BACnet client mappings (WriteProperty, ReadProperty, COV
Subscription)
- Supports trending, scheduling, and alarming locally and by referring to
remote BACnet trendlog, schedule, and notification objects
- Event-driven e-mail notification
- Supports one TP/FT-10 or EIA-852 channel (configurable)
- Supports one BACnet MS/TP or BACnet/IP channel (configurable)
- Supports B-AAC (and in addition COV, Trending)
- BACnet object configuration via LNS® “1-button configuration” tool or from
XML file
- Built-in Web server for device configuration
Specifications
InfraLIGHT BACnet Gateway
Network ports
FT-10 and EIA-852 Ethernet (IP-852)
Input voltage
12-35 V DC / 12-24 V AC
Enclosure
M36 for DIN-rail mounting (EN500022)
Dimensions
W=105mm, H=85mm, D=60mm
Environmental conditions
Operating range: 5°C...+50°C; Storage range: -10°C...+50°C; 10%-90% humidity non condensing
EMC / CE
EN14908
DIN
Order Code
Type
Description
120100K
InfraLIGHT BACnet
LonWorks / BACnet Gateway
14
FTT 24 V
InfraLIGHT Lighting scene panel
Different activities at different times of day need different lighting. InfraLIGHT
advanced scene controls provide different moods and lighting effects to suit the
occasion.
A single touch on an InfraLIGHT panel selects an appropriate lighting scene.
Up to 16 individual dimming levels for up to ten channels of lighting can be defined. Scenes can be pre-set and then recalled when needed, by simply pressing
and releasing any of the four LED-lit scene buttons. Remaining LED’s also dim
down to help indicate which scene is selected. Overall lighting levels can also be
dimmed up or down by pressing and holding either the top or bottom buttons for
dim up / dim down respectively. Lights can also be switched off without the need
for a dedicated ‘off’ scene.
The InfraLIGHT Scene Panel is available in three versions, one with a white
gloss finish and two in black satin. The black version is available with a custom
engraved legend as well as the standard silk screened legend. Interchangeable
face plates on the black version are available in a variety of finishes and can be
specified upon ordering by adding the suffix codes listed below.
A single low-voltage cable offers ‘plug and play’ connection from the plate to
Infranet Partners’ Modular Room Controllers.
-Attractive, modern aesthetic with interchangeable face plates.
-Modular, FastConnect wiring system for easy connection.
-Compatible with ‘blue box’ InfraLIGHT 200 series lighting controls and
InfraTROL 500 series integrated room controls.
Specifications
InfraLIGHT Lighting scene panel
Dimensions
Face Plate: 89 mm x 89 mm; Recess depth required: min. 30.5 mm (including connector); Fixing Centres: 61.0 mm
Housing
1.2 mm Zintec steel, powder coated, with optional metal fascia plate
Power Supply
12V DC via FastConnect cable
Connector
1 x RJ-12 Socket
LED Colour
Blue LEDs standard, green available to special order
Trim plates finish
SS: brushed stainless steel; PB: polished brass; PC: polished chrome; BN: polished black nickel; PN: satin pearl nickel
Custom Engraving
Four lines, up to eight characters per line, upper case only (model 418220C-XX only). To be specified at time of order
EN Norms
EN 60669-2-1 : 2004
Order Code
Type
Description
418100M
InfraLIGHT Lighting Scene Panel
White gloss finish, silk screened legend
418200R-XX
InfraLIGHT Lighting Scene Panel
Satin black finish, silk screened legend, with metal trim plate.
418220C-XX
InfraLIGHT Lighting Scene Panel
Satin black finish, custom engraved legend, with metal trim plate.
15
InfraLIGHT LED Driver
InfraLIGHT Driver is designed to provide power and dimming control to LED fittings. The number of fittings is limited only by the total power consumption. The
InfraLIGHT Driver is currently available in 30W and 60W versions. InfraLIGHT
Driver is housed in a robust powder-coated Zintec steel enclosure suitable for
mounting into ceiling of floor voids or into a riser. At only 38mm deep, it is easy
to install even in confined spaces and is fully compatible with the InfraLIGHT
200 range of lighting control modules.
-Universal AC input / full range
-Built in constant current limiting circuit with adjustable OCP level.
-Protections: Short circuit / overload / over voltage.
-Supports analogue (0-10V) dimming control signal.
-UL1310 Class 2 power unit.
-Cooling by free air convection.
-100% Full load burn-in test.
Specifications
InfraLIGHT LED Driver
Supply Voltage
90-260V AC 50Hz
Output Voltage
24V / 48V Dependant on model
Maximum Power Consumption
422243Q, 422483V: 30W; 422246K, 422486Q: 60W
Rated Current
422243Q: 1.25A; 422246K: 2.5A; 422483V: 0.63A; 422486Q: 1.3A
Enclosure
1.2 mm Zintec coated steel with powder coated finish
Dimensions
247 mm L x 150 mm W x 38 mm D enclosure body only
275 mm L x 150 mm W x 38 mm D overall
Operating Temperature
0 to 55 °C
EN Norms
EN 60669-2-1: 2004
24 V 230V
Order Code
Type
Description
422243Q
InfraLIGHT LED Driver
24V / 30 W
422246K
InfraLIGHT LED Driver
24V / 60 W
422483V
InfraLIGHT LED Driver
48 V / 30 W
422486Q
InfraLIGHT LED Driver
48 V / 60 W
16
InfraSENSE 200
InfraSENSE 200 meets the need for a combined lux and occupancy sensor in a
compact, attractively styled unit that will complement any décor.
Additional Slave PIR sensors can be ‘daisy chained’ to InfraSENSE 200 using
prefabricated jumper cables to extend the occupancy control zone, together with
up to two override dimmer switches.
The unit incorporates an infrared receiver which can be configured to provide
a remote on/off facility via an optional infrared remote control. An installer’s
remote control is used during commissioning to command the unit to transmit a
service pin message without the need to de-mount the device or climb a ladder
to the ceiling.
-Compact, aesthetically pleasing design
-Modular ‘Fast Connect’ system for easy connection of slave sensors, switches
-Supports up to eight slave PIR units (order code 410030Y) which are identical in
appearance and which extend the size of the occupancy control zone
-Separate LonMark®- compliant objects for Occupancy Sensor, Lux Sensor,
2 x Switch, Node Object, Scene Panel (option)
-Link powered for simplified wiring infrastructure
-InfraLIGHT LNS plug-in available for easy configuration using standard CPs
Specifications
InfraSENSE 200
Communications
LonWorks® Link Power LPT-10 (FT/10 compatible)
Network Connection
RJ-45 Socket (Pins 1+2 used)
Slave Connection
RJ-12 Socket (0V, +12V, 4 x Digital Input), supporting slave presence detector and up to two switches (configurable via plug-in)
Power Supply
42V DC ± 10% Link Power, 18mA
LonMark Obejcts
Occupancy Sensor, Lux Sensor, 2 x Switch, Node Object, Scene Panel (option)
Housing
Moulded plastic enclosure. Self-extinguishing material (UL94-VO)
Dimensions
Body: 54 mm diameter x 57 mm length overall, Face: 74 mm diameter
Recess depth required
Minimum 75 mm (including connector)
Order Code
Type
Description
410200Q
InfraSENSE 200
Integrated ceiling sensor/light controller
410065W
Spring Clip
Clip to fix into blind ceiling recess
410055R
Installer Remote
Remote control for use in commissioning
410030X
Ceiling PIR
Slave Occupancy sensor, identical appearance
17
Lighting sensors
The Lighting Sensors range has been developed specifically to complement the
InfraLIGHT Modular lighting controllers range, and the InfraSENSE 200 intelligent Light Sensor / Controller.
The range consists of a wall-mounted occupancy detector, plus ceiling-mounted
detectors for occupancy and occupancy plus light level. The ceiling-mounted
detectors match the styling of InfraSENSE 200, and can be daisy chained (occupancy sensors only) to extend the range of the occupancy detection zone in
larger rooms in conjuction with either InfraLIGHT Modular Lighting controllers
or InfraSENSE 200.
-Range of Occupancy and Light Level sensors
-Attractive, compact appearance
-Modular ‘Fast Connect’ wiring system for easy connection
-Compatible with InfraLIGHT Modular range and InfraSENSE 200
All sensors support the ‘Fast Connect’ modular sensor and switch wiring system
Specifications
Lighting sensors
Communications
Occupancy: open-collector switch; Light Level: 0..10V analogue signal
Connector
2 x RJ-12 Socket (1 on wall sensor)
Power Supply
12V DC ± 10%, 5mA
Housing
Moulded plastic enclosure. Self-extinguishing material (UL94-VO)
Dimensions
Ceiling Sensor Body: 54 mm diameter x 57 mm length overall, Face: 74 mm diameter
Wall Sensor: 62 mm wide x 80 mm high x 42 mm deep
Recess depth required
Ceiling Sensor: Minimum 75mm (including connector)
Wall Sensor: Surface mounting
EMC/CE
EN50081-1, EN50082-2
Order Code
Type
Description
410020S
Ceiling PIR/Lux
Occupancy / light level, ceiling mount
410030X
Ceiling PIR
Occupancy sensor, ceiling mount
410065W
Spring Clip
Clip to fix into blind ceiling recess
410035F
Wall PIR
Occupancy Sensor, wall mount
18
InfraLIGHT SoLo Lighting Sensor with switched-circuit control
The InfraLIGHT SoLo lighting sensor meets the need for a combined lux and
occupancy sensor to provide switched-circuit lighting control to luminaires.
The ceiling-mounted detectors match the styling of InfraSENSE 200 and are
designed to blend unobtrusively with modern décor. Mounting into suspended
ceilings is achieved via a fixing ring to secure the unit in place where the ceiling
void is accessible. Also available are a spring clip version for blind fixing and a
hard surface mount version with a ceiling receptacle and wiring access is provided
through a 20 mm round conduit entry.
- Compact, aesthetically pleasing design
-No other controller required, wires directly to fittings.
-Cyclable control modes including normal working mode, test mode, light level
mode, occupancy delay time selection.
-Adjustable occupancy hold times of 4, 8 and 16 minutes.
The unit incorporates an infrared receiver which can be configured to provide
a remote on/off facility via an optional infrared remote control. An installer’s
remote control is used during commissioning to initiate a test of the occupancy
detection, store the current light level as the light level setpoint and adjust the
occupancy hold times without the need to climb a stepladder to reach the ceiling.
Specifications
InfraLIGHT SoLo lighting sensor with analog dimming
Power Supply
3 core mains cable fitted Live, Neutral and Switched Live (black)
Rated Current
Max. 6A inductive
Housing
Moulded plastic enclosure. Self-extinguishing material (UL94-VO)
Dimensions
Body: 54 mm diameter x 57 mm length overall, Face: 74 mm diameter
Recess depth required
Minimum 75 mm
Order Code
Type
Description
423030K
InfraLIGHT SoLo
Occupancy / Light Level, suspended ceiling mount
423031R
InfraLIGHT SoLo
Occupancy / Light Level, hard surface mount
423032X
InfraLIGHT SoLo
Occupancy / Light Level, blind ceiling recess
423056K
Installer Remote
Remote control for use in commissioning
423066Q
User Remote
Remote control for manual override (switched only)
19
InfraLIGHT SoLo Lighting Sensor with analog dimming
The InfraLIGHT SoLo lighting sensor meets the need for a combined lux and
occupancy sensor to provide analog (0-10V) dimming control to luminaires.
The ceiling-mounted detectors match the styling of InfraSENSE 200 and are
designed to blend unobtrusively with modern décor. Mounting into suspended
ceilings is achieved via a fixing ring to secure the unit in place where the ceiling
void is accessible. Also available are a spring clip version for blind fixing and a
hard surface mount version with a ceiling receptacle and wiring access is provided
through a 20 mm round conduit entry.
-Compact, aesthetically pleasing design
-No other controller required, wires directly to fittings.
-Cyclable control modes including normal working mode, test mode, light level
mode, occupancy delay time selection.
-Adjustable occupancy hold times of 4, 8 and 16 minutes.
The unit incorporates an infrared receiver which can be configured to provide
a remote on/off facility via an optional infrared remote control. An installer’s
remote control is used during commissioning to initiate a test of the occupancy
detection, store the current light level as the light level setpoint and adjust the
occupancy hold times without the need to climb a stepladder to reach the ceiling.
Specifications
InfraLIGHT SoLo lighting sensor with analog dimming
Power Supply
3 core mains cable fitted Live, Neutral and Switched Live (black)
Rated Current
Max. 6A inductive
1-10 V Dimming Connector
2-pole Camden plug supplied
Housing
Moulded plastic enclosure. Self-extinguishing material (UL94-VO)
Dimensions
Body: 54 mm diameter x 57 mm length overall, Face: 74 mm diameter
Recess depth required
Minimum 75 mm
Order Code
Type
Description
423020E
InfraLIGHT SoLo
Occupancy / Light Level, suspended ceiling mount
423021L
InfraLIGHT SoLo
Occupancy / Light Level, hard surface mount
423022S
InfraLIGHT SoLo
Occupancy / Light Level, blind ceiling recess
423055D
Installer Remote
Remote control for use in commissioning
423065J
User Remote
Remote control for manual override (dimming)
20
InfraLIGHT SoLo Lighting Sensor with DSI dimming
The InfraLIGHT SoLo lighting sensor meets the need for a combined lux and
occupancy sensor to provide DSI dimming control to luminaires.
The ceiling-mounted detectors match the styling of InfraSENSE 200 and are
designed to blend unobtrusively with modern décor. Mounting into suspended
ceilings is achieved via a fixing ring to secure the unit in place where the ceiling
void is accessible. Also available are a spring clip version for blind fixing and a
hard surface mount version with a ceiling receptacle and wiring access is provided
through a 20mm round conduit entry.
-Compact, aesthetically pleasing design
-No other controller required, wires directly to fittings.
-Cyclable control modes including normal working mode, test mode, light level
mode, occupancy delay time selection.
-Adjustable occupancy hold times of 4, 8 and 16 minutes.
The unit incorporates an infrared receiver which can be configured to provide
a remote on/off facility via an optional infrared remote control. An installer’s
remote control is used during commissioning to initiate a test of the occupancy
detection, store the current light level as the light level setpoint and adjust the
occupancy hold times without the need to climb a stepladder to reach the ceiling.
Specifications
InfraLIGHT SoLo lighting sensor with DSI dimming
Power Supply
3 core mains cable fitted Live, Neutral and Switched Live (black)
Rated Current
Max. 6A inductive
DSI Dimming Connector
2-pole Camden plug supplied
Housing
Moulded plastic enclosure. Self-extinguishing material (UL94-VO)
Dimensions
Body: 54 mm diameter x 57 mm length overall, Face: 74 mm diameter
Recess depth required
Minimum 75 mm
Order Code
Type
Description
423010Y
InfraLIGHT SoLo
Occupancy / Light Level, suspended ceiling mount
423011F
InfraLIGHT SoLo
Occupancy / Light Level, hard surface mount
423012M
InfraLIGHT SoLo
OOccupancy / Light Level, blind ceiling recess
423055D
Installer Remote
Remote control for use in commissioning
423065J
User Remote
Remote control for manual override (dimming)
21
InfraTROL100 Series configurable I/O modules
The LonMark Certified InfraTROL 100 range of control modules provides a convenient, low-cost solution to a wide range of building control and light industrial
applications.
The InfraROL 100 range delivers flexible, configurable remote I/O suitable for
use as part of a networked control system. The I/O can be configured either using
an LNS®-based installation tool, or by means of a shadow object in Tridium®
Niagara (R2 or AX). The range includes a low-cost option with 8 digital inputs
and two digital outputs. Other versions feature 8 inputs individually configurable
to accept either digital or analog signals, plus a choice of analog and digital
output options.
A 64kb programmable flash memory provides storage for application programs
and data.
-Flexible, low-cost range of control modules for LonWorks® networks.
-Configurable standard firmware supplied pre-loaded.
-‘Plug and play’ relay box provides up to 8 additional switch to control loads
up to 10A per circuit.
-Support files for custom program development using Visual Control®
or Nodebuilder® are available.
InfraTROL can be used alone or in conjunction with a range of matching relay
boxes, which clip to the side of the controller unit to provide an additional 4 or 8
relay outputs each rated at 10A 230V AC. Connections between the controller and
the relay box are made automatically when the relay box is clipped into place.
Specifications
InfraTROL 100
Communications
LonWorks FT-10 network interface
Power Supply
24V DC ± 20%
Processor
Neuron 3150, 10MHz
Memory
Flash 64Kb
Maximum Current
Controller: 100 mA, Relaybox (8 relays): 200 mA , Sensor 250 mA
Inputs
Individually configurable digital and analog inputs: Volt-free contacts NO / NC, DC Voltage 0..5V, 0..10V analog, 0..24V digital,
DC current 0..5mA, Resistance (Pt1000, Photoresistive Lux)
Digital Outputs
8 Digital outputs (24V DC, current source) each capable of driving 500mA
Analog Outputs
5 mA / 0 - 10V
Dimensions
58 mm H x 86 mm L x 70 mm W
Operating Temperature
0 to 50 °C
EMC / CE
EN 50081-1 :1992, EN 50082-2 :1995
FTT MOD 230V
®
Order Code
Type
Description
201100K
InfraTROL 100
8 Digital Inputs, 2 Digital Outputs
201110Q
InfraTROL 110
8 Universal Inputs, 8 Digital Outputs
201120V
InfraTROL 120
8 Universal Inputs, 6 Digital/2 Universal Outputs
201130B
InfraTROL 130
8 Universal Inputs, 4 Digital/4 Universal Outputs
22
InfraTROL 100 MCT
The InfraTROL 100 Meter Count Totaliser is a highly optimised pulse counting
device for energy and utility meters, based on the popular InfraTROL 100 range of controllers. Ideal for connecting standard utility meters for water, gas or
electricity to a LonWorks® network. The InfraTROL 100 MCT will present the
meter pulses on up to six digital inputs as Open LonMark compliant objects. Each
object then has a number of Standard Network Variables for total pulses detected
from: Total, Today, Yesterday, This Week, Last Week, This Month and Last Month.
Functions for count reset and scaling from pulse to energy unit are also available.
-Optimised InfraTROL pulse counting application for use in Lonworks®.
- Digital inputs: Volt-free contacts Normally Open
- Two Digital outputs capable of supplying 500mA per circuit at 24V DC.
-CE, DEMKO Approvals
Two Open Loop Actuator objects are available to control the two digital outputs.
Specifications
InfraTROL 100 MCT
Communications
LonWorks FT-10 network interface
Power Supply
24V DC ± 20%
Maximum Current
Controller: 100 mA
Switch Inputs
Low Input impedance with 5mA wetting current
Enclosure
M36 for DIN-rail mounting (EN500022), self-extinguishing material (UL94VO)
Dimensions
58 mm H x 86 mm L x 70 mm W
Operating Temperature
0 to 50 °C
EMC / CE
EN 50081-1 :1992, EN 50082-2 :1995
FTT MOD 230V
®
Order Code
Type
Description
404100W
InfraTROL 100 MCT
Utility Meter interface module
23
InfraTROL 100S Series free-programmable control modules
System Integrators often need to develop project specific control strategies for
HVAC and room control applications. The solution is to use the STRATOSPHERE
graphical block programming tool together with programmable room controllers
from the InfraTROL S range.
The InfraROL S range of control modules provide a convenient, low-cost solution to a wide range of building control and light industrial applications.
-Flexible, low-cost range of control modules for LonWorks® networks.
-Configurable standard firmware supplied pre-loaded.
-‘Plug and play’ relay box provides up to 8 additional switch to control loads up
to 10A per circuit.
-Easy configuration of room control strategies using STRATOSPHERE
programming tool
A 64kb programmable flash memory provides storage for application programs
and data.
InfraTROL 100S can be used alone or in conjunction with a range of matching
relay boxes, which clip to the side of the controller unit to provide an additional 4
or 8 relay outputs each rated at 10A 230V AC. Connections between the controller
and the relay box are made automatically when the relay box is clipped into
place.
Specifications
InfraTROL 100S Series
Communications
LonWorks FT-10 network interface
Power Supply
24V DC ± 20%
Processor
Neuron 3150, 10MHz
Memory
Flash 64Kb
Maximum Current
Controller: 100 mA, Relaybox (8 relays): 200 mA , Sensor 250 mA
Inputs
Individually configurable digital and analog inputs: Volt-free contacts NO / NC, DC Voltage 0..5V, 0..10V analog, 0..24V digital,
DC current 0..5mA, Resistance (Pt1000, Photoresistive Lux)
Digital Outputs
8 Digital outputs (24V DC, current source) each capable of driving 500mA
Analog Outputs
5 mA / 0 - 10V
Dimensions
58 mm H x 86 mm L x 70 mm W
Operating Temperature
0 to 50 °C
EMC / CE
EN 50081-1 :1992, EN 50082-2 :1995
FTT MOD 230V
®
Order Code
Type
Description
200100G
InfraTROL 100S
8 Digital Inputs, 2 Digital Outputs
200110M
InfraTROL 110S
8 Universal Inputs, 8 Digital Outputs
200120S
InfraTROL 120S
8 Universal Inputs, 6 Digital/2 Universal Outputs
200130X
InfraTROL 130S
8 Universal Inputs, 4 Digital/4 Universal Outputs
24
InfraTROL 580 Series Modular Lighting and Programmable Room Controllers
InfraTROL Modular 580 combines a modular lighting controller with programmable control of room comfort functions, including heating, cooling and fan, for
use with radiators, chilled beams, electric heaters or fan coil units.
- Flexible, modular controller for lighting and comfort control
- One solution for a wide range of lighting needs
- A single controller covers all major room control functions,
- Modular ‘Fast Connect’ system for easy connection of sensors, switches
- Slim form factor for easy installation in ceiling or floor voids
- Easy configuration of room control strategies using STRATOSPHERE
programming tool
- Easy configuration of lighting control strategies via LNS plug-in
- LonWorks® FT-10 network interface for use as part of a building control
network
The unit provides 8 channels of configurable lighting control, making it suitable
general lighting control in offices, shops, hotels and other buildings where there is a need for switched-circuit lighting control together with either analogue
(1..10V) or digital (DSI) dimming.
In conjunction with the STRATOSPHERE programming tool, a wide range of
comfort-control applications can be configured to suit individual project requirements. The unit supports Open/Close valve actuators.
InfraTROL 580 is currently available in two firmware builds. Order codes ending in -CL refer to lighting controls incorporating occupancy plus constant light
control. Order codes ending in -SC refer to lighting control incorporating occupancy plus scene control.
Specification
InfraTROL 580 Series
Dimensions
350 mm long x 250 mm wide x 36 mm deep
Housing
Zinc-coated mild steel, powder coated
Power Supply
230V AC 50Hz, 20W max. (excluding lighting loads)
Mains Input
GST Male connector, 3-pole, with locking tab
Communications
LonWorks® FT-10 network interface
Lighting Outlets
GST female connector, 6-pole, with locking tab (L, N, E, Em. Live, Dim-, Dim +)
Comfort outlets
FCU Power, Electric heater, Fan control (3-speed), heating / cooling valve actuators
Circuit protection
Lighting outlets: 2 x Fuse 6A; Internal circuit: 1 x Fuse 250mA
Sensor / switch
4 x RJ-12 Modular connectors for PD, light sensor and switch;
Inputs
Space temperature (thermistor); Setpoint Offset adjuster; Window contact
Isolation
Mains–low voltage signal 4kV; Mains-DSI 2kV; DSI–low voltage signal 3kV
FTT MOD 230V
Order Code
Type
Description
433580L-CL
InfraTROL 580
8-way (SW+ANA+DSI) light & room controller, open/close valves
6-pole
434580P-CL
InfraTROL 580
8-way (SW+ANA+DSI) light & room controller, open/close valves
4+2-pole
433580L-SC
InfraTROL 580
8-way (SW+ANA+DSI) light & room controller, open/close valves
6-pole
434580P-SC
InfraTROL 580
8-way (SW+ANA+DSI) light & room controller, open/close valves 4+2-pole
25
InfraTROL 582 Modular Lighting and Programmable Room Controllers
InfraTROL Modular 582 combines a modular lighting controller with programmable control of room comfort functions, including heating, cooling and fan, for
use with radiators, chilled beams, electric heaters or fan coil units.
- Flexible, modular controller for lighting and comfort control
- One solution for a wide range of lighting needs
- A single controller covers all major room control functions,
- Modular ‘Fast Connect’ system for easy connection of sensors, switches
- Slim form factor for easy installation in ceiling or floor voids
- Easy configuration of room control strategies using STRATOSPHERE
programming tool
- Easy configuration of lighting control strategies via LNS plug-in
- LonWorks® FT-10 network interface for use as part of a building control
network
The unit provides 8 channels of configurable lighting control, making it suitable
for general lighting control in offices, shops, hotels and other buildings where
there is a need for switched-circuit lighting control together with either analogue
(1..10V) or digital (DSI) dimming.
In conjunction with the STRATOSPHERE programming tool, a wide range of
comfort-control applications can be configured to suit individual project requirements. The unit supports proportional (0..10V) actuator control.
InfraTROL 582 is currently available in two firmware builds. Order codes ending
in -CL refer to lighting controls incorporating occupancy plus constant light control. Order codes ending in -SC refer to lighting control incorporating occupancy
plus scene control.
Specification
InfraTROL 582 Series
Dimensions
350 mm long x 250 mm wide x 36 mm deep
Housing
Zinc-coated mild steel, powder coated
Power Supply
230V AC 50Hz, 20W max. (excluding lighting loads)
Mains Input
GST Male connector, 3-pole, with locking tab
Communications
LonWorks® FT-10 network interface
Lighting Outlets
GST female connector, 6-pole, with locking tab (L, N, E, Em. Live, Dim-, Dim +)
Comfort outlets
FCU Power, Electric heater, Fan control (3-speed), heating / cooling valve actuators
Circuit protection
Lighting outlets: 2 x Fuse 6A; Internal circuit: 1 x Fuse 250mA
Sensor / switch
4 x RJ-12 Modular connectors for PD, light sensor and switch;
Inputs
Space temperature (thermistor); Setpoint Offset adjuster; Window contact
Isolation
Mains–low voltage signal 4kV; Mains-DSI 2kV; DSI–low voltage signal 3kV
Order Code
Type
Description
433582Y-CL
InfraTROL 582
8-way (SW+ANA+DSI) light & room controller, analog valves
6-pole
434582C-CL
InfraTROL 582
8-way (SW+ANA+DSI) light & room controller, analog valves
4+2-pole
433582Y-SC
InfraTROL 582
8-way (SW+ANA+DSI) light & room controller, analog valves
6-pole
434582C-SC
InfraTROL 582
8-way (SW+ANA+DSI) light & room controller, analog valves
4+2-pole
26
InfraSCENE Temperature setpoint and fan-speed adjuster
Infranet Partners range of advanced room comfort controls provide user control
of temperature and ventilation at the touch of a button.
The interface consists of four push buttons illuminated by internal LEDs. The two
LEDs depicting temperature setpoint level and coloured red and blue and are
illuminated at differential brightness to indicate relative temperature setpoint.
The two LEDs depicting fan operating level are coloured green and are illuminated individually or in combination to indicate fan status.
In order to provide temperature monitoring a 10K301 Thermistor can be attached to Infranet Partners’ Modular Room Controllers using standard 2-core flying
lead and a fitted Molex plug.
- Attractive, modern aesthetic with interchangeable face plates.
- Modular, FastConnect wiring system for easy connection.
- Compatible with ‘blue box’ InfraTROL 580 series integrated lighting and room
controllers.
The InfraSCENE panel is available in three versions, one with a white gloss finish and two in black satin. The black version is available with a custom engraved
legend as well as the standard silk screened legend. Interchangeable face plates
on the black version are available in a variety of finishes and can be specified
upon ordering by adding the suffix codes listed below.
A single low-voltage cable offers ‘plug and play’ connection from the plate to
Infranet Partners’ Modular Room Controllers.
Specification
InfraSCENE Temperature setpoint and fan-speed adjuster
Dimensions
Face Plate: 89 mm x 89 mm; Recess depth required: min. 30.5 mm (including connector); Fixing Centres: 61.0 mm
Housing
1.2mm Zintec steel, powder coated, with optional metal fascia plate
Power Supply
12V DC via FastConnect cable
Connector
1 x RJ-12 Socket
LED Colour
Blue and red for temperature, green for fan speed status
Trim plates finish
SS: brushed stainless steel; PB: polished brass; PC: polished chrome; BN: polished black nickel; PN: satin pearl nickel
Custom Engraving
Four lines, up to eight characters per line, upper case only (model 438220G-XX only) to be specified at time of order
EN Norms
EN 60669-2-1 : 2004
Order Code
Type
Description
438100R
InfraSCENE Setpoint Adjuster
White gloss finish, silk screened legend
438200V-XX
InfraSCENE Setpoint Adjuster
Satin black finish, silk screened legend, with metal trim plate.
438220G-XX
InfraSCENE Setpoint Adjuster
Satin black finish, custom engraved legend, with metal trim plate
27
“Fast Connect” Modular wiring
FastConnect modular wiring provides a systematic and convenient way to install
sensors and wall switches for use with InfraLIGHT Modular lighting controllers
and InfraSENSE 200 Intelligent Light Sensor/Controller.
The range consists of 5m and 10m 6-way modular signal cables terminated with
RJ-12 modular connectors, plus a switch tail adaptor which provides a convenient
way to terminate the modular wiring into the screw terminals in a standard wall
switch plate.
Specification „Fast Connect“ Modular wiring
Cable
Halogen-free, LSF, flat 6-way modular cable
Connector
Fast Connect Modular Wiring: 2 x RJ-12 Male plug
Switch Tail adaptor: 1 x RJ-12 Female socket
Key Features:
- Modular ‘Fast Connect’ wiring system for easy connection
- Compatible with InfraLIGHT, InfraTROL Modular ranges and InfraSENSE 200
Control Network Cabling
CAT-5 Shielded twisted pair (STP) patch cables provide a convenient method
of networking InfraLIGHT and InfraTROL Modular controllers throughout a
building.
The range consists of 5m, 10m and 15m cables terminated with RJ-45 modular
connectors.
Specification „Fast Connect“ Modular wiring
Cable
6 pin CAT-5e STP modular cable
Connector
2 x RJ-45 Male plug
Key Features:
- Modular wiring system for easy connection
- Compatible with InfraLIGHT, InfraTROL Modular ranges
Order Code
Type
Description
410925P
5 m Cable
FastConnect Modular Cable, 5 m
410920G
10 m Cable
FastConnect Modular Cable, 10 m
410930M
Adaptor
FastConnect Switch tail adaptor
108307L
7 m Cable
CAT 5e STP Patch Cable, 7 m
108310V
10 m Cable
CAT 5e STP Patch Cable, 10 m
108315D
15 m Cable
CAT 5e STP Patch Cable, 15 m
28
Lighting and Room Control Connectors
The range of lighting connectors are suitable for connecting luminaires to the
InfraLIGHT Modular controller range. For the InfraTROL Modular controller
range complete connector packs are available to simplify installation for fan coil
units, heating / cooling valves as well as lighting.
- Pluggable connectors simplify installation
- Suitable for InfraLIGHT and InfraTROL Modular ranges
For lighting, where switched control only is required Wieland GST 4-pole connectors are used. Where dimming is required either Wieland GST 4-pole power
connectors with Wieland BST 2-pole dimming connectors or Wieland GST 6-pole
power and dimming connectors can be used.
Flatpack Mounting Bracket
Flatpack bracket for mounting InfraTLIGHT and InfraTTROL Modular ranges
into ceiling voids. Three-piece bracket screws into mounting lugs on controller.
- Zinc coated steel, self-coloured
- Compatible with InfraLIGHT, InfraTROL Modular ranges
Order Code
Type
Description
419184K
4-Pole lighting connector
Wieland GST 18i4
419186X
6-Pole lighting connector
Wieland GST 18i6
419142A
2-Pole dimming connector
Wieland GST 18i2
419353V
Mains power connector
Wieland GST 18i3
410995C
Flatpack Bracket
Mounting bracket for InfraLIGHT and InfraTROL Modular controllers
439542W
ConPackRC42
Complete connector pack for InfraTROL500 with Wieland 4+ 2 pole lighting plugs
439506B
ConPackRC6
Complete connector pack for InfraTROL500, includes Wieland 6 pole lighting plugs
29
STRATOSPHERE
STRATOSPHERE is a graphical design tool allowing integrators to graphically
program their own control strategies for space comfort control using InfraTROL
programmable controllers.
Simple function block programming allows you to create your applications incorporating functions from both the ISO 61131-3 standard plus many additional
application-specific function blocks supplied with STRATOSPHERE.
· Microsoft® Visio™ -based Graphical Programming using Echelon LNS®
· ISO 61131-3 compliant Function Block Programming
· Many additional HVAC function blocks for space comfort control
· Device Template and Program ID management for pre-engineering
· Design Template Manager to save time
· Re-synchronise Visio drawing from field device
STRATOSPHERE’s Project Manager allows you to create program templates and
quickly download the design into multiple controllers. Stratosphere’s debugger
lets you view the output from each function block within your design in real-time.
The entire program design is held in the controller, so even if project files are
lost, you can simply download the program design from a controller to your PC
and STRATOSPHERE will re-create the original Visio drawing from the stored
program.
Specification
STRATOSPHERE
Requirement
Computer
Pentium IV 1.8 GHz, 1024 x 768 screen
Operating system
Windows 2000 SP4 / XP SP2
Memory 512 Mb
Hard disk 200 MB available / 5400 rpm
LNS version
3.21 (minimum)
Full version includes
CD in storage case, Security Dongle, Manuals in electronic form, 3 runtime credits
Maintenance plan includes
All program updates and bug fixes, plus limited e-mail technical support
Order Code
Type
Description
282500X
Stratosphere
Stratosphere graphical software design tool - single PC licence
250100S
Stratosphere
Annual Maintenance and Update Plan
284001P
Stratosphere
Device Runtime Credit
30
InfraZONE
InfraZONE is an advanced system integration and LNS® manager tool that allows integrators to create and configure complex systems through simple graphical representations of the layout of a space.
InfraZONE reduces integration time by using templates that model your application, instead of manually engineering each application device by device.
A highly trained LonWorks® integration engineer is no longer necessary through
each phase of the integration process: the expert designs the integration rules
into an application template, allowing integration technicians to focus on their
knowledge of the application rather than the details of the network technology.
· Save time by using pre-defined application templates
· Import building floor plans from AutoCAD™
· Draw border around floor area containing control objects to create a
control zone
· Modify zones to match the changes in your building
· Separate jobs according to skill level
· Anticipate and avoid problems through pre-design of your system
· Save time by creating your GUI screens as you integrate the project
Application templates are available for all Infranet Partners standard lighting
products covering a wide variety of lighting applications.
Specification
InfraZONE
Requirement
Computer
Pentium IV 1.5 GHz, 1024 x 768 screen
Operating system
Windows 2000 SP4 / Windows XP SP2
Memory 512 Mb
Hard disk 200 Mb available / 7200 rpm
LNS version
3.21 (minimum)
LonWorks interface
NSI or VNI card
®
Order Code
Type
131300Y
InfraZONE Designer
Description
31
InfraLIGHT Designer
InfraLIGHT Designer is a device configuration tool that links with your network
management tool e.g. LonMakerTM or NL-220 to assist with the set up of InfraLIGHT equipment.
The InfraLIGHT Designer can run as a standalone application and as a device
plug-in from a network management tool. LonMark resource files are automatically updated ensuring that configuration property types designed by Infranet
Partners are correctly formatted within LNSTM. Resource files can also be updated
via a one touch button in the tool to provide a quick fix to formatting errors when
upgrading systems.
InfraLIGHT Designer provides the user with a familiar explorer style view of the
network database from which devices can be selected and configuration properties edited via simple forms. Significant engineering time for large systems can be
saved by using the tools copy and paste functions. Configuration property values
can be copied from one device to other devices in the system in just one operation.
Furthermore once configuration files have been created, they may be associated
with a colour coded TouchKey for quick and simple deployment of configuration
to devices.
Specification
· Automatically updates the LonMark resource file catalogue for InfraLIGHT
devices.
· Configuration property update function to repair formatting errors to existing
systems.
· Save time by creating configuration files for copy and paste to other devices.
· Emergency test configuration and initiation.
· Emergency test results export via CSV or XML file.
InfraLIGHT Designer
Requirement
Computer
Pentium IV 1.8 GHz, 1024 x 768 screen
Operating system
Windows 2000 SP4 / Windows XP SP2 / SP3
Memory 512 Mb
Hard disk 200 Mb available / 7200 rpm
LNS version
3.23 (minimum)
LonWorks interface
NSI or VNI compliant interface
Order Code
Type
305200D
InfraLIGHT Designer
32
Description
Easy Installation
Both the initial installation and also the maintenance of a complete DALI lighting
solutions can be quite time-consuming. Therefore Infranet Partners is glad to present two
solutions that make the installation process much easier.
Programming over iPod Touch or Plug-In
The InfraDALI controller can either be programmed using the web interface or over the
Plug-In of the LON data base. With the Airport Express (wireless router) you are able to
connect the InfraDALI light controller to an iPod-Touch, an iPhone or a similar wireless
touch panel. The use of an iPod-Touch or iPhone during the installation process allows the
system integrator to move freely in the area. Thus all important functions like setting of
groups, addressing of lamp ballasts and others can be done via this comfortable interface.
Infranet Partners designed the user interface straight forward and self-describing so that
also facility manager can do the basic installation and maintenance work without the
need of a specialized system integrator.
Programming over button commands
For maintenance work you can either use the Plug-In of
the LON database, the web-interface of the InfraDALI
controller or the configuration input. For the facility
manager the last possibility (configuration input) is the
most interesting solution: After replacing a failed lamp
ballast, you press the programmed button and the ballast
is automatically installed and configured on the lowest
available “DALI short address”. If several lamp ballasts
fail you just have to keep the correct sequence and to
configure each unit separately.
Both installation procedures can save a lot of time and
money. It allows to the system integrator to move freely
in a periphery from 50 m to the lamps
DALI
Ethernet
InfraDALI XXXX
Apple Airport Express
wireless router device
50 m
Lamp ok!
Wireless LAN terminal
(for example iPod Touch, iPhone)
33
L-IP LonWorks / IP-Router
The L-IP product family integrates LonWorks networks (FT-10/TP1250) with
Ethernet/IP-852. It routes EIA-709 (LonTalk®) packets back and forth through
an IP based network, such as a LAN (Ethernet), an Intranet, or even the Internet.
The L-IP connects to the IP network via a 100baseT Ethernet channel. In order to
provide the optimal router configuration, the L-IP is available in 4 different versions providing either 4 x TP/FT-10, 2 x TP/FT-10, 1 x TP/FT10, or 1 x TP/XF-1250.
Every L-IP supports the operating modes “Smart Switch Mode” and “Configured
Router Mode”.
- Routes packets between EIA-709 and IP networks (Ethernet)
- Fully compliant with EIA-852 and EN14908 standards
- Configured Router Mode
- Smart Switch Mode
- Support for operation behind NAT-Routers and firewalls
- Easy installation, Auto-NAT, roaming, DHCP
- Built-in EIA-852 configuration server for up to 256 members
- Remote LPA support with LPA-IP
- Configuration via built-in Web server or serial port
- MD5 authentication
- SNTP support for time synchronization
- Built-in enhanced communication test
- Supports firmware update through serial port, Ethernet, and EIA-709 channel
- Remote monitoring of the supply voltage and device temperature
Specification
L-IP LonWorks / IP-Router
Network ports
FT-10 and EIA-852 Ethernet (IP-852)
Input voltage
12-35 V DC or 12-24 V AC
Power consumption
2 W typ
Applications
Compatible with LNS applications e. g. NL220®, ALEX, LonMakerTM
Enclosure
M36 for DIN-rail mounting (EN500022)
Dimensions
LIP-1ECTB, LIP-3ECTB, LIP-33ECTB: W=105 mm, H=85 mm, D=60 mm
LIP-3333ECTB: W=157 mm, H=85 mm, D=60 mm
Environmental conditions
Operating range: 5°C...+50°C; Storage range: -10°C...+50°C; 10%-90% humidity non condensing
Order Code
Type
Description
101010K
LIP-1ECTB
L-IP 1 x Ethernet, 1 x TP/1250, temperature sensor, real-time clock
101000E
LIP-3ECTB
L-IP 1 x Ethernet, 1 x FT-10, temperature sensor, real-time clock
101002S
LIP-33ECTB
L-IP 1 x Ethernet, 2 x FT-10, temperature sensor, real-time clock
101004F
LIP-3333ECTB
L-IP 1 x Ethernet, 4 x FT-10, temperature sensor, real-time clock
34
L-Switch LonWorks Router
- For physical separation and logical connection of up to 5 EIA-709 network
segments
- Can be used as configured router
- Can be used as learning switch or repeater
- Plug & Play installation
- Forwards packets of up to 256 bytes length
- Supports up to four domains
- Forwarding decision based on subnet/node and group addresses
- Short propagation delay between ports
- Processes up to 3500 packets/s
- Supports firmware update and external configuration through each network
interface
- Network diagnostic functions and L-SwitchXP management via LSD-Tool
- CPU temperature monitor
The L-SwitchXP is the solution for interconnecting multiple LonWorks® networks
(FT-10/TP1250). It provides up to five ports and routes packets between these
ports. In spite of its small size, the L-SwitchXP router delivers first class performance and flexibility in use. In order to provide the optimal router configuration,
the L-SwitchXP comes with 2 to 5 ports as well as the two operating modes “Smart
Switch Mode” and “Configured Router Mode”.
Specification
L-Switch Router
Network ports
FT-10 and EIA-852 Ethernet (IP-852)
Input voltage
12-35 V DC or 12-24 V AC
Power consumption
2 W typ
Applications
Compatible with LNS applications e. g. NL220®, ALEX, LonMakerTM
Enclosure
M36 for DIN-rail mounting (EN500022)
Dimensions
LS-xxCB: W=105mm, H=85mm, D=60mm
LS-xxxxxCB: W=157mm, H=85mm, D=60mm
Environmental conditions
Operating range: 5°C...+50°C; Storage range: -10°C...+50°C; 10%-90% humidity non condensing
Order Code
Type
Description
101021W
LS-13CB
L-Switch 1 x TP1250, 1 x FT/10
101020Q
LS-33CB
L-Switch 2 x FT/10
101030V
LS-13300CB
L-Switch 1 x TP1250 Port, 2 x FT/10 Port
101040B
LS-33300CB
L-Switch 3 x FT-10 ports
35
NIC High Speed Network Interfaces
- Network Interface for EIA-709 and EIA-852 (IP-852) network channels
- Available for USB, PCI bus, and Ethernet port
- Create up to 8 network nodes with a single network interface (MNI devices)
- Use the LPA, LSD Tool , your ORION applications, MIP applications, and LNS®
(VNI) applications on a single network interface at the same time
- Compatible with BMS e.g. Honeywell EBI, TAC VISTA, etc.
- Compatible with LNS® applications in high performance VNITM mode e.g.
NL220, NLFacilities, NLOPC-VNI, ALEX, NetWorker, LonMaker® etc.
- Compatible with MIP applications (LDV interface) e.g. NodeUtil32, NLUtil,
NLOPC-MIP, Honeywell CARE 5/7, etc.
- Compatible with high performance ORION applications (ORION API)
- NIC-852 is fully compatible with L-IP and i.LON® 600 Internet routers
- Use legacy MIP applications together with the IP-852 (Ethernet) channel
- Software selectable transceivers on NIC709-USB and NIC709-PCI: FT-10/LP-10,
RS-485, and TP/XF-1250/2500
- Runs on Windows 2000/XP®/2003/Vista
- Runs on Linux 2.6 (NIC709-PCI)
The NIC product range from Loytec are the most universal network interfaces for
LonWorks networks (FT-10/TP1250) with Ethernet/IP-852. Based on the revolutionary ORION and L-Chip technologies, they offer high packet update rates and
low response times. All NICs are fully compatible with products like NL220, ALEX,
LNS® 3.x and LNS® TE applications, LonMaker®, NodeUtil32, NLUtil, OPC servers, and with high performance ORION applications. The multiplexed network
interface (MNI) support allows starting multiple MIP applications in parallel to an
LPA, LSD Tool, NL220, or LonMaker® on a single network interface.
Specification
L-Switch Router
Network ports
NIC-709-USB / NIC709-PCI: FT-10, TP1250, RS-485 NIC709-IP3E100: TP1250
Power Supply
NIC-709-USB: via USB, NIC709-PCI: via PCI bus, NIC709-IP3E100: 12-35 VDC / 12-24 VAC, 40-70 Hz
Current consumption
NIC-709-USB: < 130 mA NIC709-IP3E100: 170 mA @ 12 VDC
Applications
Compatible with LNS applications e. g. NL220®, ALEX, LonMakerTM
Bit rate
NIC-709-USB / NIC709-IP3E100: 300 bps - 2.5 Mbps
Enclosure
NIC709-IP3E100: M36 for DIN-rail mounting (EN500022)
Dimensions
NIC709-USB100: W=116mm, H=69mm, D=23mm
NIC852: W=51mm, H=20mm, D=8mm
NIC709-IP: W=145mm, H=91mm, D=28mm
Order Code
Type
Description
102210W
NIC-709-USB
NIC-709-USB Connects to the USB port of a PC
102240N
NIC709-PCI
NIC709-PCI Connects to the PCI bus of a PC
102260Y
NIC-852
NIC-852 USB dongle connects to the USB port of a PC
102270F
NIC709-IP3E100
NIC709-IP3E100 Remote Network Interface. Connects to PC via Ethernet
36
L-INX Automation Servers
The new powerful LINX Automation servers provide data access through web services (OPC XML/DA or OPC COM/DCOM with OPC-BR800) to connect SCADA or
ERP systems. State of the art connectivity functions such as scheduling, alarming,
and trending can be implemented and these functions are accessible via the Web
UI using a standard web browser or the L-WEB application (.NET) on a Windows
PC or mobile devices like PDA’s or Smart Phones running Windows Mobile. Customised pages with dynamic content can be created for L-WEB with the L-VIS
configuration tool supplied with the unit.
For integration in LonMark® systems the LINX-100 includes built in Remote Network Interface with 2 MNI devices and the LINX-101 includes a built in LonWorks/
IP Router. LINX-200 provides a solution for integration with BACnet® systems.
- Hosts customized pages with dynamic content
- Supports trending, scheduling, and alarming locally
- Alarm notification via e-mail
- Embedded OPC XML/DA server fully compliant with the OPC XML/DA standard
- Supports up to 1000 OPC data points
- Built-in Web server for device configuration
- SNTP support for time synchronization
- Built-in communication test
- Status and activity LEDs
- OPC status and activity LED
- Network statistics information accessible through OPC data points
- 12-35 V DC / 12-24 V AC supply voltage
- 105 x 86 x 60 (L x W x H in mm)
- DIN-rail mountable
Specification
L-INX Automation Servers
Network ports
FT-10 and EIA-852 Ethernet (IP-852)
Input voltage
12-35 V DC or 12-24 V AC
Power consumption
2 W typ
Applications
Compatible with LNS applications e. g. NL220®, ALEX, LonMakerTM
Enclosure
M36 for DIN-rail mounting (EN500022)
Dimensions
W=210 mm, H=165 mm, D=60 mm
Environmental conditions
Operating range: 5°C...+50°C; Storage range: -10°C...+50°C; 10%-90% humidity non condensing
EMC / CE
EN14908
Order Code
Type
Description
105100W
LINX-100 (RNI)
Automation Server for LonWorks including a built in RNI with 2 MNI devices
105101D
LINX-101 (IP Router)
Automation Server for LonWorks including built in LonWorks/IP Router
105200B
LINX-200
Automation Server for BACnet
37
Terms and Conditions of Sale
Definitions
“the Company” , “we” and “us” shall mean either Calon Associates Limited for orders placed in
the United Kingdom, Ingenieurbüro Brönnimann Thun for orders placed in Switzerland or Infranet
Technologies GmbH for orders placed in Germany, and / or one or more of their subsidiary companies,
successors or assignees, as appropriate
“the Customer” and “you” shall mean the person, firm or company placing the order with the
Company.
“Goods” means the goods or services and “Services” means the services which the Company is to
supply in accordance with these terms.
“Contract” means the Contract for the purchase and sale of Goods.
Supply of Goods
All Goods are offered for sale subject to availability. Prices charged for Goods shall be as specified in
the Company’s current price lists, unless otherwise quoted in writing.
Unless otherwise quoted in writing, payment is due strictly within 30 days of invoice date for approved
account Customers. Non-account Customers must enclose payment with order, unless otherwise
agreed in writing.
The Company may amend its price list at any time. In the case of an exchange rate fluctuation or
increase in raw material costs of greater than 2% occurring between the date of quotation or date
of preparation of the price list and the date of delivery, the Company reserves the right to increase
the amount invoiced to reflect the variation in exchange rate. Customers are advised to re-confirm
prices at the time of ordering.. All Goods remain the property of the Company until full payment
for the Goods has been received. After delivery of the Goods to the Customer, the Goods shall be at
the Customer’s risk. The Customer agrees to take all necessary measures to safeguard and insure
the Goods for their full reinstatement value, to promptly disclose to the Company upon request the
location(s) where the Goods are stored, and to promptly grant the Company unrestricted access to
any premises where such Goods may be stored, for the purpose of repossession, in the event that the
Customer fails to make promptly any payment due.
All source code, designs and other intellectual property associated with the Goods to be supplied
remain the property of their respective owners and are used under license. Failure to pay promptly
any software license fees due may render a software license liable to termination.
All Goods are warranted against failure due to manufacturing defects for a period of one year from
the date of supply, or for such warranty period as may be offered by the ultimate manufacturer of the
Goods. Any Goods which are found by the Company to have failed during the warranty period due
to a manufacturing defect will be replaced, repaired or the purchase price credited, at the Company’s
sole option. Apart from such warranty, all Goods are sold ‘as is’, without any warranty as to their
suitability for use in any specific application. The Customer must satisfy themselves prior to purchase
that the Goods are suitable for use in the intended application as the Company will not accept Goods
returned for reasons of unsuitability. Since the conditions of installation, configuration and use of
the Goods are beyond the Company’s control, the Company shall not be liable for any failure of
Customer’s application or system incorporating the Goods.
These terms and conditions apply in preference to and supersede any terms and conditions referred
to, offered or relied on by the Customer, whether in negotiation or at any stage in dealings between
the Company and the Customer with reference to the Goods to which this Contract relates. Unless
otherwise specifically agreed in writing these terms and conditions shall be incorporated in every offer
quotation acceptance and contract for the sale or supply of goods or services by the Company and
together with the order to which they relate constitute the entire Contract between the Company and
the Customer. The Company shall not be bound by any standard or printed terms furnished by the
Customer unless specifically agreed in writing.
Unless otherwise specified in writing, all prices are quoted in the local currency of the Company, and
are valid for thirty days from the date of quotation. All prices are subject to VAT where applicable.
Payment terms are as stated above or as quoted in writing. The Company reserves the right to review
from time to time and amend without notice the payment terms and/or amount of credit offered to
the Customer.
All orders are subject to written acceptance by the Company and no Contract shall be concluded until
such confirmation is given or the Customer’s order is otherwise accepted. Unless otherwise stated in
writing by the Company each order when accepted shall constitute a separate Contract.
Cancellation of the order following acceptance by the Company but prior to delivery shall render the
Customer liable to pay a cancellation fee equal to the greater of either 15% of the order value, or the
proportion of the total order value (at the prices quoted) expended or committed by the Company on
Goods, labour and materials in connection with the order up to the point of cancellation.
In the event that any invoice balance shall be outstanding 14 days after the due date, any and all sums
owed by the Customer to the Company shall become due for immediate payment and the Company
may suspend or determine the Contract or any unfilled part thereof. Any overdue balances may incur
a late payment charge of 2% of the outstanding balance per month. The Customer agrees to pay any
such charges, together with any costs incurred by the Company in recovering any overdue payment,
whether before or after judgement.
Delivery times specified are approximate only. The Company will use its best efforts to ensure that
the product(s) are delivered and / or services performed within the specified time scale, but shall not
be liable for any failure to meet any specified or preferred delivery date.
The Customer shall not assign its interest in the Contract without the written consent of the Company.
If the Company assigns its interest in the Contract it shall promptly notify the Customer of such
assignment.
The Customer warrants that it has complied with every applicable lawful requirement or instruction
and (without Limitation) that it has obtained every necessary licence permit or authority that may be
required in connection with the supply of Goods and Services to be carried out hereunder.
General
The Customer shall indemnify the Company for any loss damage expense or liability in any suit or
proceeding based upon any claim for the infringement of Intellectual Property Rights brought against
the Company resulting from the Company’s compliance with the Customer’s designs or specifications
and for any such infringement involving any marking or branding applied by the Company at the
request of the Customer
The Company will exercise reasonable skill and care in the performance of services and the supply
of Goods. However, the Company shall not be liable for any losses or damage, whether direct or
consequential, arising directly or indirectly from the use of any product(s) supplied or service(s)
performed.
The Company shall not be liable to the Customer for any failure to fulfil its obligations under the
Contract if such failure is caused by circumstances beyond its reasonable control. In such event the
Company undertakes to notify the Customer as promptly as possible of any such failure.
Failure by the Company to fully exercise any provision in these terms and conditions or to take
advantage of any of its rights hereunder shall not be construed as a waiver of such provision or the
relinquishment of such right.
If any part or clause of this contract shall be found to be unenforceable, this shall not prejudice the
Company’s right to enforce the remaining clauses of this contract.
Limitation of Liability
All conditions, terms, representations and warranties relating to the Goods and or services supplied
under this agreement, whether imposed by statute or operation of law or otherwise, that are not
expressly stated in these terms and conditions including, without limitation, the implied warranty
of satisfactory quality and fitness for a particular purpose are hereby excluded, subject always to the
following:
Nothing in these terms and conditions shall exclude the Company’s liability for death or personal
injury resulting from our negligence.
The Company’s total aggregate liability to you for any claim in contract, tort, negligence or otherwise
arising out of or in connection with the provision of the goods and services shall be limited to the
charges paid by you in respect of the goods and services which are the subject of any such claim.
In any event no claim shall be brought unless you have notified us of the claim within one year of
it arising.
In no event shall we be liable to you for any loss of business, contracts, profits or anticipated savings
or for any other indirect or consequential or economic loss whatsoever.
The Customer shall indemnify the Company against all damage or injury to any person firm or
company and against all actions claims demands costs charges and expenses (including costs charged
on a reasonable basis for the time of the Company’s executives) for which the Company may become
liable in respect of the Goods sold or Services supplied under a contract except to the extent admitted
expressly in these Conditions and unless such damage or injury shall have been a direct result of the
negligence of the Company and can be attributed to no other cause (whether in whole or in part).
Jurisdiction
The performance of this Contract shall be governed by the laws of the country in which the Company
is domiciled, and the courts of such country shall have sole jurisdiction. The place of jurisdiction shall
be at the location of the nearest appropriate court to the place of the Company‘s registered domicile.
E. & O. E. ( rev9.80 g)
Edition 2009
Infranet Partners Sales Offices
UK
Infranet Partners UK
CH, AT, DE
Infranet Partners Schweiz
Calon Associates Ltd
Daresbury Innovation Centre
Keckwick Lane
Daresbury WA4 4FS, UK
Phone +44 (0) 845 345 9355
Fax +44 (0) 845 345 9385
sales@infranet-partners.co.uk
IBT Ing.büro Brönnimann Thun
Kasernenstrasse 5
CH-3600 Thun
www.infranet-partners.co.uk
www.infranet-partners.ch
Phone +41 (0) 33 223 00 80
Fax +41 (0) 33 223 00 84
info@infranet-partners.ch
www.infranet-partners.com