EFS Factory Sealed Pilot Lights

advertisement
Cl. I, Div. 1 & 2, Groups B,C,D
Cl. II, Div. 1, Groups E,F,G
Cl. II, Div. 2, Groups F,G
Cl. lll
NEMA 3,7BCD,9EFG
5C-B
EFS Factory Sealed
Pilot Lights
; 1 (
t 0 1 Dimensions Pg. 5C-2
CROUSE-HINDS*
Pilot lights listed below are factory sealed and
do not require external seals. Lamps • are 6
watt, type S6, candelabra base for use on
110-125 volt circuits.
Enclosures with single pilot covers only can
be equipped with a transformer for each lamp
for higher voltages as shown.
Double device pilot light covers cannot be so
arranged as the transformer occupies the
space of one pilot light.
Transformer Voltages Above 125
Cat.
Primary
Nominal Volts
No.
50-60 hertz
Voltage
Range
Suffix
Transformer
220/11 0
220-240
T2
440/110
440-480
T4
T5
550/110
550-600
Explosionproof
Dust-lgnitionproof
Raintight
Wet Locations
Class I, Group B:
All enclosures listed above are suitable for
Class I, Group B, Div. 1 usage. Seals only
have to be installed on 1 inch conduit within
5 ft. if1 Division 1.
These products are suitable for Group B,
Div. 2 as listed, without external seals.
EFS Single Gang
Enclosure with Single Pilot Light•
Hub
Dead End
Through Feed
Size
Cat. #
Cat. #
1h
EFS11524-t
EFSC11524-t
3.1.4
EFS21524-t
EFSC21524-t
1
EFS31524-t
EFSC31524-t
Enclosure with Double Pilot Lights •
1h
EFS1156H
EFSC11561-t
3.1.4
EFS21561-t
EFSC21561-t
1
EFS31561-t
EFSC31561-t
t
Add oolor symbol for each p ilot light from table below.
Example: EFS1561 with red and green lights is EFS1561-J t-J3.
Color
Red
Green
Symbol
J1
J3
Color
Amber
Clear
Symbol
J6
J10
Color
Blue
Symbol
J11
• LED pilot lights can be furnished in place of standard incandescent pilot lamps. Add suffix
LED to catalog number after color symbol.
For 24 VDC operation, add suffix 5300.
Copyright* 2000 Cooper Industries, Inc.
5C-O
EFS and EDS Factory Sealed
Control Devices and Manual
; 1 4
Motor Starting Switches
t 0 1 Dimensions Pg. 5C-2
CROUSE·HINDS"
Application:
Factory sealed enclosures are installed in a
rigid metallic conduit system for surface
mounting adjacent to or remote from
equipment being controlled and are used:
• to prevent arcing of enclosed device from
causing ignition of a specific hazardous
atmosphere or atmospheres external to the
enclosure
• in industrial areas such as chemical plants,
oil and gas refineries, paint and varnish
manufacturing plants, gasoline bulk loading
terminals, grain elevators, grain processing
industries, coal processing or handling areas,
or metal handling or finish ing areas where
atmosphere may contain hazardous gases
and/or dust
• in non-hazardous areas where sturdy,
durable enclosures are required
• in conjunction with magnetic starters or
contactors for remote control of motors
Manual motor starting switch enclosures are
used:
• for manual starting of small ac or de motors
• to provide manual starting and stopping
and, in the case of units with heaters, motor
running protection
Cl. I, Div. 1 & 2, Groups B*,C,D
Cl. II, Div. 1, Groups E,F,G
Cl. II, Div. 2, Groups F,G
Cl. lll
NEMA 3,7B*CD,9EFG
• Shafts - stainless steel
• Shaft bushings- stainless steel
• Rocker handle and pushbutton guards type 6/6 nylon
• Sealing enclosur~s- copper-free aluminum
Standard Finishes:
Feraloy iron alloy - electrogalvanized and
aluminum acrylic paint
• Copper-free aluminum- natural
• Type 6/6 nylon- black
• Stainless steel - natural
Explosionproof
Dust-lgnitionproof
Raintight
Wet Locations
Certifications and
Compliances:
• NEC/CEC:
Class I, Division 1 & 2, Groups B* ,C,D
Class II, Division 1, Groups E,F,G
Class II, Division 2, Groups F,G
Class Ill
• NEMNEEMAC: 3,7B*CD,9EFG
• UL Standard: 894, 698
• CSA Standard: C22.2 No. 30
Options:
The following special options are available
from the factory by adding suffix to Cat. No.
Suffix to be
Added to
Cat.#
De scription
Emergency "Stop" button (momentary) -front operated red mushroom button ..... . .... S111
Lockout provision on front operated pushbutton cover (standard on buttons
marked " OFF" and "STOP") ........ . .... . ................................... • .... S153
For 24 VDC operation on pilot lights ... . ... . ....... . .... . .. . ..... . ............ . .. . .. S300
Features:
Factory sealed devices have many distinct
advantages:
• reduce installation problems
• eliminate external seals
• lower installation costs
• improve safety
• are used with general purpose snap and
pushbutton type switches
• standard neoprene covers for front
operated pushbuttons. Prevents
accumulation of dirt and entrance of water
around operating shafts
• mounting lugs and taper tapped hubs with
integral bushings
• large machine screws for fastening covers
to bodies
• lockout provisions on front operated push
button (marked "STOP" and " OFF" ) and
selector switch covers
hasp is
• lockout hole for padlock having
provided when used with covers for front
lever and side rocker type operation
• close tolerances in machining of wide,
mating flanges and journalled shafts and
bearings for front button operation, produces
flametightness of enclosure joints
• on enclosures with front lever and side
rocker type operating handles, threaded type
shafts and bushings are used to ensure
flametightness
• dead end (EFS or EDS) or through feed
(EFSC or EDSC) hubs - lh" to 1" sizes
Three-position selector switches with modified operation:
Momentary contact clockwise operation, spring return to center, maintained
contact counter-clockwise operation .... . .. . . . . . . . .. . . . . . .. . ... ....... . . .. ... . .. S634
Momentary contact counter-clockwise operation, spring return to center,
maintained contact clockwise operation ....... . ... . .. . . . . . .... ... . . ..... •• ...... S635
Bodies and covers (single and two gang units) - copper-free aluminum . ................. . SA
Where indicated in the catalog listings, EDS units suitable for Class I, Division 1,
Group B usage can be supplied. EFS units are suitable for Class I, Division 1,
Group Bas standard .. ... . .................. . .. .. ............. . .. . . . .. . ............ GB
Maintained contact mushroom head with lockout and guard. Maximum one per cover
and cannot be used with a pilot light with a transformer or another standard pushbutton ... S769
EDS bodies and factory sealed cover and device sub-assemblies are available for field
assembly (see pages 4C-10 to 12).
v.·
Suffix 5 769
Standard Materials:
• Bodies - Feraloyo iron alloy (U.S.); copperfree aluminum (Canada).
• Front operated pushbutton and pilot light
covers- Feraloy iron alloy
• Side operated type pushbutton covers copper-free aluminum
* See Options: suffix GB
Copyright" 2000 Cooper Industries, Inc.
Download