EDS Factory Sealed Selector Switches 5C-8 CM, Div. 1 & 2, Groups B*,C,D Cl. II, Div. 1, Groups E,F,G Cl.ll, Div. 2, Groups F,G Cl. Ill NEMA3,7B*CD,9EFG Maintained Contact, 600VAC Heavy Duty, Dimensions Pg. 5C-2 Explosionproof Dust-lgnitionproof Raintight Wet Locations Furnished with pushbuttons, cam actuated by a maintained contact selector mechanism to operate in the sequences shown in the diagrams below. Specify indicating plate markings. See table below listings. EDS11273 Single Gang Style Position 1 Enclosure With Switch Position 2 Position 3 Replacement Pushbuttons t T\A/OI VVvJ Position, TwoCircuit TVA/OI W\J Position, FourCircuit A1 »!• A2 • • A1 fi« A2 • • B1 JLLA B2 • • A1 •!• T\A/O1 Ww A2 • • A1 •!• A2 Through Feed Cat. # ED11 1 /2 % 1 EDS11271 EDS21271 EDS31271 EDSC11271 EDSC21271 EDSC31271 **• ED12 1 /2 % 1 EDS11272 EDS21272 EDS31272 EDSC11272 EDSC21272 EDSC31272 1 /2 3/4 1 EDS11273 EDS21273 EDS31273 EDSC11273 EDSC21273 EDSC31273 ED12 1 /2 3/4 1 EDS11274 EDS21274 EDS31274 EDSC11274 EDSC21274 EDSC31274 ED12 1 /2 3/4 1 EDS11275 EDS21275 EDS31275 EDSC11275 EDSC21275 EDSC31275 M •if • • «i* r* • • •i* r* ••• 1 w * B1 ftl* •.• ... B2 • • ^« w* A1 A2 •£ r9 ftiA ua • • •• B1 B2 HI* • • AiA *.» • • V^ ED11 Circuit ThreePosition, FourCircuit Dead End Cat. # •i* Thrpp1 1 II CC Position, Hub Size 1 Standard indicating plate markings available are as follows: Two-Position RUN, JOG HAND, AUTOMATIC FORWARD, REVERSE * For Class 1, Group B: Consider using EPS series selector switches, see page 5C-13. All enclosures listed above can be modified for Class I, Group B, Div. 1 usage. Add suffix GB to the Cat. No. Seals must be installed within 1V4" of each conduit opening in Division 1. These products are suitable for Group B, Div. 2 as listed, without external seals. In Canada, for Group B applications consult factory, t For replacement pushbuttons, see page 4C-6. FAST, SLOW OPEN, CLOSE UP, DOWN ON, OFF IN, OUT RAISE, LOWER START, STOP Three-Position RUN, OFF, JOG HAND, OFF, AUTOMATIC FORWARD, OFF, REVERSE FAST, OFF, SLOW Copyright" 2000 Cooper Industries, Inc. 1.OFF, 2 OPEN, OFF, CLOSE UP, OFF, DOWN 5C-0 CROUSE-HINDS* ^H EPS and EDS Factory Sealed Control Devices and Manual Motor Starting Switches Cl. 1, Div. 1 & 2, Groups B*,C,D Cl. II, Div. 1 , Groups E,F,G Cl. II, Div. 2 , Groups F,G Cl. III Dimensions Pg. 5C-2 1 I!M| Y If Application: Factory sealed enclosures are installed in a rigid metallic conduit system for surface mounting adjacent to or remote from equipment being controlled and are used: • to prevent arcing of enclosed device from causing ignition of a specific hazardous atmosphere or atmospheres external to the enclosure • in industrial areas such as chemical plants, oil and gas refineries, paint and varnish manufacturing plants, gasoline bulk loading terminals, grain elevators, grain processing industries, coal processing or handling areas, or metal handling or finishing areas where atmosphere may contain hazardous gases and/or dust • in non-hazardous areas where sturdy, durable enclosures are required • in conjunction with magnetic starters or contactors for remote control of motors Manual motor starting switch enclosures are used: • for manual starting of small ac or dc motors • to provide manual starting and stopping and, in the case of units with heaters, motor running protection Features: Factory sealed devices have many distinct advantages: • reduce installation problems • eliminate external seals • lower installation costs • improve safety • are used with general purpose snap and pushbutton type switches • standard neoprene covers for front operated pushbuttons. Prevents accumulation of dirt and entrance of water around operating shafts • mounting lugs and taper tapped hubs with integral bushings • large machine screws for fastening covers to bodies • lockout provisions on front operated push button (marked "STOP" and "OFF") and selector switch covers • lockout hole for padlock having Vi" hasp is provided when used with covers for front iever and side rocker type operation • close tolerances in machining of wide, mating flanges and journalled shafts and bearings for front button operation, produces flametightness of enclosure joints • on enclosures with front lever and side rocker type operating handles, threaded type shafts and bushings are used to ensure flametightness • dead end (EPS or EDS) or through feed (EFSC or EDSC) hubs -1/2" to 1" sizes NFf\/lA 3 7R *rr~) QFFG W L / j wL-l v^ 1 ^ ) ' L / - • Shafts - stainless steel • Shaft bushings - stainless steel • Rocker handle and pushbutton guards type 6/6 nylon • Sealing enclosures - copper-free aluminum Standard Finishes: Feraloy iron alloy - electrogalvanized and aluminum acrylic paint • Copper-free aluminum - natural • Type 6/6 nylon - black • Stainless steel - natural Certifications and Compliances: • NEC/CEC: Class I, Division 1 & 2, Groups B*,C,D Class II, Division 1, Groups E,F,G Class II, Division 2, Groups F,G Class III • NEMA/EEMAC: 3,7B*CD,9EFG • UL Standard: 894, 698 • CSA Standard: C22.2 No. 30 Options: The following special options are available from the factory by adding suffix to Cat. No. Suffix to be Added to Cat. # Description Emergency "Stop" button (momentary) - front operated red mushroom button Lockout provision on front operated pushbutton cover (standard on buttons marked "OFF" and "STOP") For 24 VDC operation on pilot lights Three-position selector switches with modified operation: Momentary contact clockwise operation, spring return to center, maintained contact counter-clockwise operation Momentary contact counter-clockwise operation, spring return to center, maintained contact clockwise operation Bodies and covers (single and two gang units) - copper-free aluminum S111 S153 S300 S634 S635 SA Where indicated in the catalog listings, EDS units suitable for Class I, Division 1, Group B usage can be supplied. EFS units are suitable for Class I, Division 1, Group B as standard GB Maintained contact mushroom head with lockout and guard. Maximum one per cover and cannot be used with a pilot light with a transformer or another standard pushbutton... S769 EDS bodies and factory sealed cover and device sub-assemblies are available for field assembly (see pages 4C-10 to 12). Suffix S769 Standard Materials: • Bodies - Feralof iron alloy (U.S.); copperfree aluminum (Canada). • Front operated pushbutton and pilot light covers - Feraloy iron alloy • Side operated type pushbutton covers copper-free aluminum Explosionproof Dust-lgnitionproof Raintight Wet Locations ' See Options: suffix GB Copyright" 2000 Cooper Industries, Inc.