W0076
ASSEMBLY AND INSTALLATION
INSTRUCTIONS
WARNING: BE SURE TO SHUT OFF POWER AT THE MAIN FUSE OR CIRCUIT
BREAKER BOX BEFORE INSTALLING OR SERVICING THIS FIXTURE.
NOTE: 1. Before installing, consult local electrical codes for wiring and grounding requirements.
2. READ AND SAVE THESE INSTRUCTIONS.
Parts:
Parts Number (4785MM)
Parts Number (4791SS)
Parts Number (9465FO)
Parts Number (9464CW)
Set Screw-1 (X6)(E)
Mounting Screw (A)
Wire Nut (P3)(B)
Parts Number (4789SS)
Anchor (C)
Dry Wall Screw (D)
Set Screw-2 (X6)(F)
Interior Glass
Shade (G) (X3)
Exterior Glass
Shade (H) (X3)
Exterior Glass (H)
Mounting Screw (A)
Back Plate
Green Grounding Screw
Dry Wall Screw (D)
Bulb T10 Max.75W
(not included)
Set Hole
Mounting Plate
Anchor (C)
Fixture Wire
Fixture Grounding Wire
Wire Nut (B)
House Grounding Wire
Interior Glass (G)
Set Screw-1 (E)
Outlet Box
Set Screw-2 (F)
Metal Ring
Headless Screw
“ L ” Screwdriver
1. Unsecure the headless screws by using “ L ” Screwdriver , carefully remove mounting plate from
back plate.
2. Attach the mounting plate to the wall.
a) If the wall material is wood:
Attach the mounting plate to the outlet box by using two mounting screws, then secure the dry wall
screws through the set holes to the wall.
b) If the wall material is cement:
130618
Place the mounting plate to the outlet box and mark the target on the wall from the set hole for
drilling two holes. Remove the mounting plate. Drill the holes and thread the anchors into the
holes, then attach the mounting plate to the outlet box by using two mounting screws. Secure the
dry wall screws through the set holes into the anchors.
3. Pull out the outlet wires and the house grounding wire from the outlet box. Make wire connections
by using the wire nuts:
---Connect the black (hot) wire from the fixture to the black (hot) wire from the power source.
---Connect the white (neutral) wire from the fixture to the white (neutral) wire from the power
source.
---Attach the fixture grounding wire to the mounting plate with the green grounding screw. Then
connect it to the house grounding wire with a wire nut.
Fig.1
Carefully put the wires back into the outlet box.
Exterior Glass (I)
4. Attach the back plate to the mounting plate, secure the
headless screws from the bottom hole of the back plate
onto the the bottom side of the mounting plate, using
supplied “ L ” Screwdriver.
5. Install a bulb (not included). See relamping label at socket
area or packaging for maximum allowed wattage.
6. Place the interior glass shade into the support, adjust the
slot of the interior glass shade to locate into the arm of the
Slot
fixture, thread the two set screws-1 through each holes of
interior glass shades, and then secure them into the support.
Interior Glass (H)
(See Fig. 1)
Set Screw-1 (F)
Slot
7. Place the interior glass shade into the center of exterior
glass shade and metal ring, adjust the slot of the exterior
glass shade to locate into the arm of the fixture, then thread
Support
the two set screws-2 through each holes of metal ring and
Metal Ring
Set Screw-2 (G)
exterior glass shades, secure them into the set screws-1.
Arm
(See Fig. 1)
Back Plate
8. Turn on the power at the main fuse or circuit breaker box.
A: 21"
B
B: 9-3/4"
C: 4"
A
C
130618