ACE ACE BACKSTAGE CO., INC. E CO. STAG BACK CLEAR PUSH COM DMX12 PUSH STAGE POCKET SYSTEMS Stage Pocket Systems / Panel Fabrication / Spec Fabrication / Stage Management Products 122SLBK COMPARE CONNECTORS CONNECTRIX, Neutrik® & Switchcraft® Page 19 PANELS CONNECTRIX and Custom Spec Page 21 Full Stage Pocket Page 4 STAGE MANAGEMENT Solutions to Common Problems Page 23 CUSTOM SPEC FABRICATION Pockets and Panels Page 24 24846 Avenue Rockefeller • Suite 200 • Valencia, CA 91355 • Issue #612 Tel: 661-295-5760 • Fax: 661-295-1122 • Web: www.acebackstage.com ACE POCKET SELECTION GUIDE VERTICAL SLANT PANEL POCKETS STANDARD GENERAL USE VERTICAL SLANT PANEL POCKETS feature an open access design to make installing connector panels easy. They are load tested to withstand commercial point loads while preventing connector damage. Hard finished with electrostatic powder coat in two neutral colors, as well as designer finishes for a clean appearance. Installed as part of the ACE Pocket System, these pockets can be used in all floor types and can accommodate up to 24 connections. See pages 19-21 for panel and connector details. CONNECTRIX See Pages 19 for details Mini Pocket Half Pocket Full Pocket Double Wide Pocket Capacity: Up to (4) CONNECTRIX Connectors Capacity: Up to (6) CONNECTRIX Connectors Capacity: Up to (12) CONNECTRIX Connectors Capacity: Up to (24) CONNECTRIX Connectors Pages 14-15 Pages 12-13 Pages 4-5 Pages 6-7 Load Test Results HORIZONTAL PANEL POCKETS CONNECTRIX See Pages 19 for details SUPER CAPACITY HORIZONTAL PANEL POCKETS have increased, super capacity, of up to 50 connections using horizontally mounted panel brackets in the back-box pocket body. They offer the same rugged construction, finishes, and weight load verification with twice the connectivity as our vertical panel pockets. This two-piece pocket consists of a separate back box-pocket body and lid/bezel. *Note: Connector capacity limitations apply depending on connectors and panels used. Super Pocket Super Double Wide Pocket Capacity: Up to (25) CONNECTRIX Connectors Capacity: Up to (50) CONNECTRIX Connectors Pages 8-9 Pages 10-11 TABLE TOP POCKETS CONNECTRIX See Pages 19 for details TABLE TOP POCKETS were developed to provide easy conference room access to all types of necessary connectivity. Easily installed into any table top, these pockets allow convenient power, and panel mounted or cable-end connections. Built to withstand institutional use and complemented with features that protect the pocket and itÕ s connections. Available in our signature black powder coat finish, each table top pocket can accommodate up to 12 connections. *Note: Connector capacity limitations apply depending on connectors and panels used. Table Top Pocket Conference Port Capacity: Up to (12) CONNECTRIX Connectors Capacity: (8) or More Cables Page 22 Pages 22 ACE CONNECTRIX PANEL GUIDE PSW-100 CONNECTRIX POCKET PANELS (Page 20) CONNECTRIX WALL & RACK PANELS (Page 21) POCKET PANELS are cut, coated, engraved and loaded in house. Designed as part of the ACE Pocket System, these panels are flat and strong. They mate perfectly with ACE Pockets and utilize our CONNECTRIX cutout detail to combine custom connector options and immediate delivery. WALL & RACK PANELS come in standard sizes, but can also be made to your custom needs. Rack panels are immediately available in semi gloss black and wall panels come in semi gloss black or white. Featuring our CONNECTRIX cutout detail, ACE Wall and Rack Panels maximize the number of connectors on each panel. Custom connector engraving and company logo engraving adds a professional flair. CONNECTRIX See Pages 19 for details 2 ACE BACKSTAGE CO., INC. • 24846 Avenue Rockefeller • Suite 200 • Valencia, CA 91355 • Tel: 661-295-5760 • Fax: 661-295-1122 • www.acebackstage.com ACE BACK BOX SELECTION GUIDE BACK BOXES BACK BOXES are designed exclusively for use with ACE vertical panel pockets and are finished in electro deposited zinc for corrosion resistance. Available in many depths, allowing clearance for feed through or distribution junction, using combination knock-outs. Welded steel construction includes a disposable protective cover and accepts accessory brackets for isolation of high and low voltage. See pages 16-17 for back box details. 6” Deep Pages 17 Isolated 8” Deep Isolated Moisture Resistant Coating 12” Deep Pages 17 Pages 17 Pages 17 BACK ACCESS COVERS BACK ACCESS COVERS are used to close the back access opening in ACE vertical panel pockets after wires have been terminated. Use a BAC in a raised floor installation, and add an isolation bracket when separation of high and low voltage is necessary. See page 16 for back access cover details. Isolated Back Access Cover Back Access Cover Pages 16 Pages 16 ACE STAGE MANAGEMENT GUIDE STAGE MANAGEMENT PRODUCTS were created to offer solutions to installation challenges. A variety of items, each one specifically addressing an installation hassle, and offering a simple solution. See page 23 for stage management product details. Choir Stick Microphone Microphone Softpod Pages 23 Mic Hanger Slug Pages 23 Pages 23 ACE CONNECTRIX CONNECTOR GUIDE CONNECTRIX Connectors eliminate the need for a custom cut panel. Our modular system seamlessly mates each connector into prepunched cutouts in our CONNECTRIX Panels. Using this system, we can ship pocket panels, wall panels, or rack panels immediately. No need to wait for a custom cut panel. See page 19 for connector details. Single Space Double Space Triple Space Pages 19 Pages 19 Pages 19 CUSTOM POCKET AND PANEL FABRICATION ACEÕ s Custom Spec Panel Fabrication Services produce panels which are precision cut and engraved to your exact specifications from a variety of materials on precision CNC rotary cutting machines. ACEÕ s Custom Services also include Custom Spec Pocket Fabrication Services See page 21 for custom panel engraving and fabrication details. See Back Cover for custom spec pocket details. Custom Spec Pockets Back Cover Custom Engraved Panels Page 21 Input Input 11 22 3 3 4 4 Trigger DC-4500 SEISMOELECTRONICS DC-4500 SEISMOELECTRONICS GROUNDWATER LOCATOR GROUNDWATER LOCATOR Trigger USB to Computer USB to Computer Power Power Battery Charge Battery Charge ACE BACKSTAGE CO., INC. • 24846 Avenue Rockefeller • Suite 200 • Valencia, CA 91355 • Tel: 661-295-5760 • Fax: 661-295-1122 • www.acebackstage.com 3 FULL STAGE POCKET 122SLBK - FULL POCKET DESCRIPTION The Full Stage Pocket by ACE Backstage Co., Inc. is made from heavy gauge, die-cut steel. This professional box provides a rugged, flush mounted space to conceal and protect stage connections. The vertical slant panel design provides an open access to the conduit, allowing connector panels to be terminated before or after pocket installation. This feature brings flexibility to the installation process, allowing rough-in or completion-stage connector termination. CONNECTRIX SYSTEM READY All ACE Stage Pockets are compatible with interchangeable CONNECTRIX System Panels and isolated connector configurations. Designed to maximize space and allow adequate receptacle clearance, CONNECTRIX Panels house a larger number of connections than a standard ganged plate and allow for a customized configuration. For more information on CONNECTRIX Panels see pg. 20 For more information on CONNECTRIX Connectors see pg. 19 ACE STAGE POCKETS Standard Vertical Slant Panel CONNECTOR CAPACITY Super Horizontal Slant Panel Up to (12) connections or (6) connections & (1) dual gang A/C OR x 12 (4 ((4) 4)) 4 (6 ((6) 6) (12) ( ) (24 ((24) 24) 24) ((25) 25) 25) Body Measurement: Floor Cutout Size: Cableway Slot: Powder Coat Finishes: x2 (50) (50) 50) PANEL OPTIONS FEATURES Lid and Flange Measurement: + x6 10.5”L x 10.5”W x 0.937”D 7.187”L x 8.0”W x 4.5”D 8.5” x 8.5” 3/8” x 8” #MP-100 • Textured Black Decorator (BK) • Antique Coppervein (CV) PNL-100 PSW-100 #PE #PNL-120 #PNL-140 Special Order Lid & Bezel: Interchangeable Lids: UL Listed: Panel Placement: Compatible ACE Panel Series: • Solid Brass (BR) • Stainless Steel (SS) • Standard Lid (SL) • Carpet Lid (CL) INCLUDES • Locking Lid (LL) • Modified Length Lid (ML) Yes Vertical • PE • PNL-120 • PNL-100 • PSW-100 UL LISTED UL Listed compliance Standard 514A file FLOOR BOX 44LK Suitable for raised floor applications 4 • (1) Vertical, Slant Panel Style, Stage Pocket • (1) Interchangeable Lid • (2) Hinge Pins and Spring Fasteners • (8) Installation Screws • (1) Capture Slot Closure OPTIONS Locking Lid Enlarged Cable Exit Carpet Lid Back Access Cover Back Box pg. 18 pg. 18 pg. 18 pg. 16 pg. 17 ACE BACKSTAGE CO., INC. • 24846 Avenue Rockefeller • Suite 200 • Valencia, CA 91355 • Tel: 661-295-5760 • Fax: 661-295-1122 • www.acebackstage.com 4.500" FRONT VIEW 6.000" OPTIONAL BACK BOX WELDED 14 GAUGE PROUDLY MADE IN THE U.S.A. www.acebackstage.com FULL STAGE POCKET 8.000" VERTICAL SLANT POCKET 8.250" 10.000" CAPTIVE SLOT CLOSURE DROPS INTO BOX WHEN CABLE WAY SLOT IS IN USE NOMINAL OPENING CONNECTRIX A FLEXIBLE CONNECTOR AND PANEL SYSTEM Choose Pre-fabricated audio, communications, data, electric, video, and voice connectors and panels, or create custom panels as needed using the CONNECTRIX System of panels and connectors. TOP VIEW 10.500" 8.5" x 8.5" CUTOUT IN STAGE FLOOR WHEN MOUNTING IN STAGE FLOOR WITHOUT ACE #102BBX BACK BOX .375" CABLE WAY SLOT CAPTIVE SLOT CLOSURE DROPS INTO BOX WHEN CABLE WAY SLOT IS IN USE 4.500" OPEN BACK ACCESS SECTION VIEW 59/64" NOM. 8.000" .500" 7.187" 16 GAUGE (.060" THICK) WELDED STEEL POCKET BODY CONSTRUCTION 1.500" NOMINAL .500" 8.000" TRIM BEZEL 6.000" 1.875" NOM. 3.656" .500" REMOVABLE HINGE PINS PERMIT EASY LID EXCHANGE FOR CUSTOM LID CONFIGURATIONS .500" 10.000" 10.500" OPEN ACCESS 4.500" FRONT VIEW 6.000" OPTIONAL BACK BOX WELDED 14 GAUGE 8.000" 8.250" 10.000" CAPTIVE SLOT CLOSURE DROPS INTO BOX WHEN NOMINAL ¨ Download DWG DXF PDF Spec Sheets CABLE WAY SLOT & IS IN USEAutoCAD , and OPENING for ALL ACE Stage Pockets at www.acebackstage.com STANDARD POCKET HALF PANEL CONNECTRIX A FLEXIBLE CONNECTOR AND PANEL SYSTEM Choose Pre-fabricated audio, communications, data, electric, PANELS FOR USE WITH 122XXXX video, and voice connectors and panels, or create custom panels ELECTRICAL PANEL FULL PANEL as needed using the CONNECTRIX System of panels and connectors. REMOVABLE HINGE PINS PERMIT EASY LID EXCHANGE FOR CUSTOM LID CONFIGURATIONS .500" PNL-100/PSW-100 SERIES SECTION VIEW APPROVALS DRAWN PNL-120 SERIES PE SERIES OPEN BACK ACCESS DATE 4.500" FULL POCKET MODEL NUMBERS MODEL # #122CLBK #122CLCV #122LLBK #122SLBK #122SLCV #222CLBR #222SLBR #322CLSS #322SLSS 6.000" FINISH Electrostatic applied powdercoat 59/64" NOM. 1.875" NOM. 3.656" CUSTOMER APPROVAL 8.000" 7.187" MATERIAL 11ga CRS - Lid & Flange 16ga CRS - Pocket Body 16 GAUGE (.060" THICK) WELDED STEEL POCKET BODY CONSTRUCTION 1.500" NOMINAL 10.000" DESCRIPTION Black Full Pocket w/ Carpet Lid Copper Vein Full Pocket w/ Carpet Lid Black Full Pocket w/ Lid Punched for Lock Black Full Pocket w/ Standard Lid Copper Vein Full Pocket w/ Standard Lid Brass Full Pocket w/ Carpet Lid Brass Full Pocket w/ Standard Lid Stainless Steel Full Pocket w/ Carpet Lid Stainless Steel Full Pocket w/ Standard Lid ITEM 122XXXX DESCRIPTION Full-sized floor pocket to house up to (12) connectors DOUBLE WIDE POCKET 124SLBK - DOUBLE WIDE POCKET DESCRIPTION The size of this Double Wide Pocket allows for a large connector capacity in a flush mounted, vertical slant panel pocket. Built from cold roll steel, die pressed and expertly welded, forming a consistently square, dimensionally stabile enclosure to conceal connectivity and prevent connector damage. Use the interchangeable CONNECTRIX Panel System when designing your connector configuration to include audio, video, electric AC power, data, control, and switches. CONNECTRIX SYSTEM READY All ACE Stage Pockets are compatible with interchangeable CONNECTRIX System Panels and isolated connector configurations. Designed to maximize space and allow adequate receptacle clearance, CONNECTRIX Panels house a larger number of connections than a standard ganged plate and allow for a customized configuration. For more information on CONNECTRIX Panels see pg. 20 For more information on CONNECTRIX Connectors see pg. 19 ACE STAGE POCKETS Standard Vertical Slant Panel CONNECTOR CAPACITY Super Horizontal Slant Panel Up to (24) connections or (12) connections and (2) dual gang A/C x 24 (4) (6) (12) ((24) (25) OR Body Measurement: Floor Cutout Size: Cableway Slot: Powder Coat Finishes: + x4 (50) PANEL OPTIONS FEATURES Lid and Flange Measurement: x 12 18.5”L x 10.5”W x 0.937”D 7.187”L x 16”W x 4.5”D 8.5” x 16.5” 3/8” x 16” #MP-100 • Textured Black Decorator (BK) • Antique Coppervein (CV) PNL-100 PSW-100 #PE #PNL-120 #PNL-140 Special Order Lid & Bezel: Interchangeable Lids: UL Listed: Panel Placement: Compatible ACE Panel Series: • Solid Brass (BR) • Stainless Steel (SS) • Standard Lid (SL) • Carpet Lid (CL) INCLUDES • Locking Lid (LL) • Modified Length Lid (ML) Yes Vertical • PNL-100 • PE • PNL-120 • FP3E • PSW-100 UL LISTED UL Listed compliance Standard 514A file FLOOR BOX 44LK Suitable for raised floor applications 6 • (1) Vertical, Slant Panel Style, Stage Pocket • (1) Interchangeable Lid • (2) Hinge Pins and Spring Fasteners • (16) Installation Screws • (2) Capture Slot Closures OPTIONS Locking Lid Enlarged Cable Exit Carpet Lid Back Access Cover Back Box pg. 18 pg. 18 pg. 18 pg. 16 pg. 17 ACE BACKSTAGE CO., INC. • 24846 Avenue Rockefeller • Suite 200 • Valencia, CA 91355 • Tel: 661-295-5760 • Fax: 661-295-1122 • www.acebackstage.com PROUDLY MADE IN THE U.S.A. www.acebackstage.com DOUBLE WIDE STAGE POCKET VERTICAL SLANT POCKET .500" (2) CAPTIVE SLOT CLOSURES DROP INTO BOX WHEN CABLEWAY SLOT IS IN USE NOMINAL OPENING CONNECTRIX A FLEXIBLE CONNECTOR AND PANEL SYSTEM Choose Pre-fabricated audio, communications, data, electric, video, and voice connectors and panels, or create custom panels as needed using the CONNECTRIX System of panels and connectors. .500" 18.500" REMOVABLE HINGE PINS PERMIT EASY LID EXCHANGE FOR CUSTOM LID CONFIGURATIONS TOP VIEW 16.000" 11 GAUGE (.120" THICK) STEEL TRIM BEZEL AND LID ASSEMBLY WITH POWDER COAT FINISH INSIDE AND OUTSIDE • ANTIQUE COPPER VEIN • TEXTURED BLACK • BRUSHED BRASS* • STAINLESS STEEL* 4.500" 4.500" OPEN BACK ACCESS 6.000" *Solid Brass or Stainless Steel Metal *Finish Available as Special Order SECTION VIEW 59/64" NOM. 1.875" NOM. 3.656" 16.8" x 8.5" CUTOUT IN STAGE FLOOR WHEN MOUNTING IN STAGE FLOOR WITHOUT ACE #104BBX BACK BOX 6.000" 7.187" 8.000" 16 GAUGE (.060" THICK) WELDED STEEL POCKET BODY CONSTRUCTION 1.500" NOMINAL 10.000" .500" .500" 1.250" TYPICAL TRIM BEZEL .375" CABLE WAY SLOT 10.500" (2) CAPTIVE SLOT CLOSURES DROP INTO BOX WHEN CABLE WAY SLOT IS IN USE Download DWG & DXF AutoCAD¨ , and PDF Spec Sheets for ALL ACE Stage Pockets at www.acebackstage.com TRIM BEZEL 4.500" 6.000" OPTIONAL BACK BOX WELDED 14 GAUGE (.071" THICK) STEEL 10" X 18" X 6" ZINC PLATED (ACE #104BBX BACK BOX) OR OPTIONAL BACK ACCESS COVER 14 GAUGE (.071" THICK) STEEL ZINC PLATED (ACE #24BAC BACK ACCESS COVER - NOT SHOWN) FRONT VIEW 16.000" 16.240" 18.000" STANDARD POCKET PANELS FOR USE WITH 124XXXX HALF PANEL FULL PANEL ELECTRICAL PANEL PNL-100/PSW-100 SERIES PNL-120 SERIES PE SERIES APPROVALS DRAWN CUSTOMER APPROVAL DATE DOUBLE WIDE POCKET MODEL NUMBERS MODEL # #124CLBK #124CLCV #124LLBK #124SLBK #124SLCV #224CLBR #224SLBR #324CLSS #324SLSS FINISH Electrostatic applied powdercoat MATERIAL 10ga CRS - Lid & Flange 16ga CRS - Pocket Body DESCRIPTION Black Double Wide Pocket w/ Carpet Lid Copper Vein Double Wide Pocket w/ Carpet Lid Black Double Wide Pocket w/ Lid Punched for Lock Black Double Wide Pocket w/ Standard Lid Copper Vein Double Wide Pocket w/ Standard Lid Brass Double Wide Pocket w/ Carpet Lid Brass Double Wide Pocket w/ Standard Lid Stainless Steel Double Wide Pocket w/ Carpet Lid Stainless Steel Double Wide Pocket w/ Standard Lid ITEM 124XXXX DESCRIPTION Double-wide floor pocket to house up to (24) connectors SUPER STAGE POCKET 132SLBK - SUPER STAGE POCKET DESCRIPTION Introducing ACE’s large-capacity, horizontal panel mount pocket. It has the same above floor footprint as the standard Full Pocket (10.5” x 10.5”) with almost three times the connectivity. Built from die-cut heavy gauge welded steel, the ACE Super Pocket resists bending even under the most severe stage loads. The Super Pocket system incorporates three sub-assemblies, allowing “just in time” delivery for each phase of construction. Phase #1 – The pocket body incorporates horizontal panel brackets with an isolated AC raceway enclosure, mounted inside a full sized ACE steel back box. Generous combination knockouts provide in, out, and thru ways for cabling. If ordered separately: BRK102BBX. Phase #2 – Pre-loaded connectors can be easily terminated during this phase before the stage floor is finished, enabling the installer to solder without worry of disturbing the finished floor. CONNECTRIX Panels arrive loaded with CONNECTRIX Connectors and can be custom engraved per your specifications. *Replace the back box cover to protect the pockets internal assembly until phase 3. Phase #3 – The unique lid and bezel assembly mounts directly to the installed pocket body, allowing concealed connectivity to be accessed through the blind-hinged lid. If ordered separately: BZ132XXYY CONNECTRIX SYSTEM READY All ACE Stage Pockets are compatible with interchangeable CONNECTRIX System Panels and isolated connector configurations. Designed to maximize space and allow adequate receptacle clearance, CONNECTRIX Panels house a larger number of connections than a standard ganged plate and allow for a customized configuration. ACE STAGE POCKETS Standard Vertical Slant Panel (4) (6) (12) Super Horizontal Slant Panel (24) (25) When using PNL-140 Series Panels, Choose from CONNECTRIX Connector series: • C-15000 • C-20000 • C-25000 • C-27000 (50) FEATURES Lid and Flange Measurement: Body Measurement: Floor Cutout Size: Cableway Slot: Powder Coat Finishes: Special Order Lid & Bezel: Interchangeable Lids: UL Listed: 10.0”L x 10.0”W x 6.0”D CONNECTOR CAPACITY 10.0” x 10.0” Up to (25) connections and (2) dual gang A/C 3/8” x 8” x 25 • Textured Black Decorator (BK) • Antique Coppervein (CV) • Solid Brass (BR) • Stainless Steel (SS) • Standard Lid (SL) • Carpet Lid (CL) • Locking Lid (LL) • Modified Length Lid (ML) Yes Panel Placement: Horizontal Compatible ACE Panels: • PNL-100 • PNL-140 + x4 COMPLETE SYSTEM INCLUDES • (1) Back Box Pocket Body with Horizontal Panel Brackets Installed • (1) Interchangeable Lid • (2) Hinge Pins and Springs • (8) Installation Screws • (1) Capture Slot Closure • PNL-120 • PSW-100 UL LISTED UL Listed compliance Standard 514A file FLOOR BOX 44LK Suitable for raised floor applications 8 For more information on CONNECTRIX Panels see pg. 20 For more information on CONNECTRIX Connectors see pg. 19 10.5”L x 10.5”W x 0.937”D OPTIONS Locking Lid Enlarged Cable Exit Carpet Lid Extended Back Box pg. 18 pg. 18 pg. 18 pg. 17 ACE BACKSTAGE CO., INC. • 24846 Avenue Rockefeller • Suite 200 • Valencia, CA 91355 • Tel: 661-295-5760 • Fax: 661-295-1122 • www.acebackstage.com SUPER STAGE POCKET PROUDLY MADE HORIZONTAL PANEL POCKET IN THE U.S.A. www.acebackstage.com .375" CABLE WAY SLOT NOMINAL OPENING REMOVABLE SPRING LOADED HINGE PINS PERMIT EASY LID EXCHANGE FOR CARPET, LOCKING, AND STANDARD LID CONFIGURATIONS LID (BLIND HINGE), SPRING LOADED PINS, AVAILABLE IN STANDARD FLUSH , STANDARD FLUSH LOCKING, OR RECESSED CARPET TRIM BEZEL MOUNTING FLANGE & LID ASSEMBLY .500" .500" 8.000" CONNECTRIX PANEL SYSTEM COMBINATION OF "#PNL-100", "#PNL-120", OR "#PNL-140" STAGE POCKET PANELS SUPER STAGE POCKET BACK BOX #BRK102BBX 3.375" Download DWG & DXF AutoCAD¨ , and PDF Spec Sheets for ALL ACE Stage Pockets atNOMINAL www.acebackstage.com 2.335" OPENING BARRIER ISOLATED AC SECTION CREATED WHEN #BRK102 BRACKET KIT ASSEMBLY IS INSTALLED BARRIER ISOLATED LOW VOLTAGE SECTION CREATED WHEN #BRK102 BRACKET KIT ASSEMBLY IS INSTALLED 7.250" REMOVABLE SPRING LOADED HINGE PINS PERMIT EASY LID EXCHANGE FOR CARPET, LOCKING, AND STANDARD LID CONFIGURATIONS LID (BLIND HINGE), SPRING LOADED PINS, AVAILABLE IN STANDARD FLUSH , STANDARD FLUSH LOCKING, OR RECESSED CARPET STANDARD POCKET PANELS FOR USE WITH 132XXXX TRIM BEZEL MOUNTING FLANGE & LID ASSEMBLY SUPER PANEL .500" .500" HALF PANEL FULL PANEL 8.000" NOMINAL OPENING 3.375" PNL-100 SERIES PSW-100 SERIES BARRIER ISOLATED AC SECTION CREATED WHEN PE#BRK102 SERIESBRACKET KITDC/DB ASSEMBLY IS INSTALLED PANELS PNL-120 SERIES PNL-140 SERIES LID (BLIND HINGE), SPRING LOADED PINS, AVAILABLE IN STANDARD FLUSH , STANDARD FLUSH LOCKING, OR RECESSED CARPET APPROVALS TRIM BEZEL MOUNTING FLANGE & LID ASSEMBLY A/C COVER CONNECTRIX PANEL SYSTEM COMBINATION OF "#PNL-100", "#PNL-120", OR "#PNL-140" STAGE POCKET PANELS SUPER STAGE POCKET BACK BOX #BRK102BBX 2.335" DRAWN .500" BARRIER ISOLATED SPRING LOADED LOW VOLTAGEREMOVABLE SECTION HINGE PINS PERMIT EASY LID CREATED WHEN #BRK102 EXCHANGE FOR CARPET, LOCKING, AND STANDARD LID CONFIGURATIONS BRACKET KIT ASSEMBLY IS INSTALLED DATE 7.250" 2.530" 10.000" SQUARE CUSTOMER APPROVAL SUPER STAGE POCKET BACK BOX #BRK102BBX 3.375" "CONNECTRIX" PANEL SYSTEM COMBINATION OF "#PNL-100", "#PNL-120", OR "#PNL-140" SUPER STAGE POCKET MODEL NUMBERS MODEL # #132CLBK #132CLCV #132LLBK #132SLBK #132SLCV #232CLBR #232SLBR #332CLSS #332SLSS FINISH Electrostatic applied .500" powdercoat MATERIAL 11ga CRS - Lid & Flange 14ga CRS - Pocket Body 8.000" BARRIER ISOLATED AC SECTION CREATED WHEN #BRK102 BRACKET KIT ASSEMBLY IS INSTALLED 2.530" 10.000" SQUARE DESCRIPTION Black Super Pocket w/ Carpet Lid Copper Vein Super Pocket w/ Carpet Lid Black Super Pocket w/ Lid Punched for Lock Black Super Pocket w/ Standard Lid Copper Vein Super Pocket w/ Standard Lid Brass Super Pocket w/ Carpet Lid Brass Super Pocket w/ Standard Lid Stainless Steel Super Pocket w/ Carpet Lid Stainless Steel Super Pocket w/ Standard Lid ITEM 132XXXX DESCRIPTION Super floor pocket to house up to (25) connectors SUPER DOUBLE WIDE POCKET 134SLBK - SUPER DOUBLE WIDE POCKET DESCRIPTION ACE Backstage Co., Inc’s Super Double Wide Pocket is designed for high capacity connectivity in a horizontal panel mount configuration. ACEÕ s unique pocket design uses a reinforced hinge-tube, heavy duty lid stops, and a wide mounting bezel to distribute weight loads. The Super Double Wide Pocket system incorporates three subassemblies, allowing “just in time” delivery of each part for each phase of construction. Phase #1 – The pocket body incorporates horizontal panel brackets, mounted inside a double wide sized ACE steel back box. Generous combination knockouts provide in, out, and thru ways for cabling. If ordered separately: BRK104BBX. Phase #2 – Pre-loaded connectors can be easily terminated during this phase before the stage floor is finished, enabling the installer to solder without worry of disturbing the finished floor. CONNECTRIX Panels arrive loaded with CONNECTRIX Connectors and can be custom engraved per your specifications. *Replace the back box cover to protect the pockets internal assembly until phase 3. Phase #3 – The unique lid and bezel assembly mounts directly to the installed pocket body, allowing concealed connectivity to be accessed through the blind-hinged lid. If ordered separately: BZ134XXYY CONNECTRIX SYSTEM READY All ACE Stage Pockets are compatible with interchangeable CONNECTRIX System Panels and isolated connector configurations. Designed to maximize space and allow adequate receptacle clearance, CONNECTRIX Panels house a larger number of connections than a standard ganged plate and allow for a customized configuration. ACE STAGE POCKETS Standard Vertical Slant Panel (4) (6) (12) Super Horizontal Slant Panel (24) (25) When using PNL-140 Series Panels, Choose from CONNECTRIX Connector series: • C-15000 • C-20000 • C-25000 • C-27000 (50) FEATURES Lid and Flange Measurement: Body Measurement: Floor Cutout Size: Cableway Slot: Powder Coat Finishes: Special Order Lid & Bezel: Interchangeable Lids: UL Listed: Panel Placement: Compatible ACE Panel Series: For more information on CONNECTRIX Panels see pg. 20 For more information on CONNECTRIX Connectors see pg. 19 10.5”L x 8.5”W x 0.937”D 10.0”L x 18.0”W x 6.0”D CONNECTOR CAPACITY 10.0” x 18.0” Up to (50) connections or (25) connections and (2) triple gang A/C 3/8” x 16” • Textured Black Decorator (BK) • Antique Coppervein (CV) x 50 • Solid Brass (BR) • Stainless Steel (SS) • Standard Lid (SL) • Carpet Lid (CL) • Locking Lid (LL) • Modified Length Lid (ML) Horizontal • PNL-120 • PE x 12 (1) Back Box Pocket Body with Horizontal Panel Brackets Installed (1) Interchangeable Lid & Trim Bezel (2) Hinge Pins and Springs (8) Installation Screws (1) Capture Slot Closure • PNL-140 • FP3E UL LISTED UL Listed compliance Standard 514A file FLOOR BOX 44LK Suitable for raised floor applications 10 x 25 COMPLETE SYSTEM INCLUDES Yes • PNL-100 • PSW-100 OR OPTIONS Locking Lid Enlarged Cable Exit Carpet Lid Extended Back Box pg. 18 pg. 18 pg. 18 pg. 17 ACE BACKSTAGE CO., INC. • 24846 Avenue Rockefeller • Suite 200 • Valencia, CA 91355 • Tel: 661-295-5760 • Fax: 661-295-1122 • www.acebackstage.com PROUDLY MADE HORIZONTAL PANEL POCKET IN THE U.S.A. www.acebackstage.com SUPER DOUBLE WIDE STAGE POCKET .500" 10.500" LID (BLIND HINGE), SPRING LOADED PINS, AVAILABLE IN STANDARD FLUSH , STANDARD FLUSH LOCKING, OR RECESSED CARPET NOMINAL OPENING TRIM BEZEL MOUNTING FLANGE AND LID ASSEMBLY REMOVABLE SPRING LOADED HINGE PINS PERMIT EASY LID EXCHANGE FOR CARPET, LOCKING, AND STANDARD LID CONFIGURATIONS .937" 18.500" LID STOP WITH RUBBER PAD, 2 PLACES TOP VIEW 16.000" (2) HINGED CABLE WAYS LOT CLOSURES 8.000" SUPER DOUBLE WIDE STAGE POCKET BACK BOX #BRK104BBX 14 GAUGE SHEET STEEL CRS (.071" THICK) WITH A CLEAR ZINC FINISH 11 GAUGE (.120" THICK) STEEL TRIM BEZEL MOUNTING FLANGE AND LID ASSEMBLY WITH POWDER COAT FINISH INSIDE AND OUTSIDE • ANTIQUE COPPER VEIN • TEXTURED BLACK • BRUSHED BRASS* • STAINLESS STEEL* RIGHT SIDE SECTION CONNECTRIX PANEL SYSTEM COMBINATION OF "#PNL-100", "#PNL-120", OR "#PNL-140" STAGE POCKET PANELS 3.281" 6.000" COMBINATION KNOCK-OUTS 1/2" AND 3/4", 1 PLACE TYPICAL ON OPPOSING SIDES *Solid Brass or Stainless Steel Metal *Finish Available as Special Order 2.375" 1.000" 5.000" .500" 10.000" .500" .375" CABLE WAYS LOT 1.250" TYPICAL TRIM BEZEL .500" 10.500" TRIM BEZEL MOUNTING FLANGE AND LID ASSEMBLY .500" .500" .937" Download DWG & DXF AutoCAD¨ , and PDF Spec Sheets for ALL ACE Stage Pockets at www.acebackstage.com 16.250" FRONT SECTION SUPER DOUBLE WIDE STAGE POCKET BACK BOX #BRK104BBX 14 GAUGE SHEET STEEL CRS (.071" THICK) WITH A CLEAR ZINC FINISH CONNECTRIX PANEL SYSTEM COMBINATION OF "#PNL-100", "#PNL-120", OR "#PNL-140" STAGE POCKET PANELS SET THE SUPER STAGE POCKET BACK BOX #BRK104BBX SECURELY BRACED INTO THE FLOOR TO PROVIDE SUPPORT EQUAL TO THE FLOOR LOADING REQUIREMENTS, ACCOUNTING FOR ANY HEIGHT OFFSET REQUIRED FOR THE FINISHED FLOOR 6.000" COMBINATION KNOCK-OUTS 1/2", 3/4", AND 1-1/4", 2 PLACES TYPICAL ON OPPOSING SIDES 1.312" 15.376" 18.000" 1.312" STANDARD POCKET PANELS FOR USE WITH 132XXXX SUPER PANEL HALF PANEL FULL PANEL ELECTRICAL PANEL PNL-100 SERIES PNL-120 SERIES PE SERIES PNL-140 SERIES APPROVALS DRAWN CUSTOMER APPROVAL DATE 1.312" SUPER STAGE POCKET MODEL NUMBERS MODEL # #134CLBK #134CLCV #134LLBK #134SLBK #134SLCV #234CLBR #234SLBR #334CLSS #344SLSS FINISH Electrostatic applied powdercoat MATERIAL 11ga CRS - Lid & Flange 14ga CRS - Pocket Body DESCRIPTION Black Super Double Wide Pocket w/ Carpet Lid Copper Vein Super Double Wide Pocket w/ Carpet Lid Black Super Double Wide Pocket w/ Lid Punched for Lock Black Super Double Wide Pocket w/ Standard Lid Copper Vein Super Double Wide Pocket w/ Standard Lid Brass Super Double Wide Pocket w/ Carpet Lid Brass Super Double Wide Pocket w/ Standard Lid Stainless Steel Super Double Wide Pocket w/ Carpet Lid Stainless Steel Super Double Wide Pocket w/ Standard Lid ITEM 134XXXX DESCRIPTION Super floor pocket to house up to (50) connectors HALF POCKET 123SLBK - HALF POCKET DESCRIPTION This medium-capacity ACE Pocket is the Half Stage Pocket. This vertical slant panel pocket is made of heavy gauge steel, and has been load tested to withstand momentary weight loads of more than 1000 lbs. Install this pocket in the floor surface for flush mounted, easy access to (6) CONNECTRIX Connectors or (1) single gang AC outlet. CONNECTRIX SYSTEM READY All ACE Stage Pockets are compatible with interchangeable CONNECTRIX System Panels and isolated connector configurations. Designed to maximize space and allow adequate receptacle clearance, CONNECTRIX Panels house a larger number of connections than a standard ganged plate and allow for a customized configuration. For more information on CONNECTRIX Panels see pg. 20 For more information on CONNECTRIX Connectors see pg. 19 ACE STAGE POCKETS Standard Vertical Slant Panel CONNECTOR CAPACITY Super Horizontal Slant Panel Up to (6) connections or (1) dual gang A/C x6 (4) ((6)) (12) (24) (25) Body Measurement: Floor Cutout Size: Cableway Slot: Powder Coat Finishes: Special Order Lid & Bezel: Interchangeable Lids: UL Listed: Panel Placement: Compatible ACE Panel Series: PANEL OPTIONS 6.875”L x 10.5”W x 0.937”D 4.375”L x 7.187”W x 4.5”D 4.75” x 8.5” 3/8” x 4” #MP-100 • Textured Black Decorator (BK) • Antique Coppervein (CV) PNL-100 PSW-100 #PE • Standard Lid (SL) • Carpet Lid (CL) INCLUDES • Locking Lid (LL) • Modified Length Lid (ML) Yes Vertical • PNL-100 • PE #PNL-120 #PNL-140 • Solid Brass (BR) • Stainless Steel (SS) • (1) Vertical, Slant Panel Style, Stage Pocket • (1) Interchangeable Lid • (2) Hinge Pins and Spring Fasteners • (8) Installation Screws • (1) Capture Slot Closure • PSW-100 UL LISTED UL Listed compliance Standard 514A file FLOOR BOX 44LK Suitable for raised floor applications 12 x2 (50) FEATURES Lid and Flange Measurement: OR OPTIONS Locking Lid Enlarged Cable Exit Carpet Lid Back Access Cover Back Box pg. 18 pg. 18 pg. 18 pg. 16 pg. 16 ACE BACKSTAGE CO., INC. • 24846 Avenue Rockefeller • Suite 200 • Valencia, CA 91355 • Tel: 661-295-5760 • Fax: 661-295-1122 • www.acebackstage.com FLOOR WHEN MOUNTING IN STAGE FLOOR WITHOUT ACE #103BBX BACK BOX HALF STAGE POCKET .500" .375" CABLE WAY SLOT .500" PROUDLY MADE IN THE U.S.A. www.acebackstage.com 10.500" VERTICAL SLANT POCKET CAPTIVE SLOT CLOSURE DROPS INTO BOX WHEN CABLE WAY SLOT IS IN USE NOMINAL OPENING Download DWG & DXF AutoCAD¨ , and PDF Spec Sheets for ALL ACE Stage Pockets at www.acebackstage.com .500" CONNECTRIX A FLEXIBLE CONNECTOR AND PANEL SYSTEM Choose Pre-fabricated audio, communications, data, electric, video, and voice connectors and panels, or create custom panels as needed using the CONNECTRIX System of panels and connectors. 11 GAUGE (.120" THICK) STEEL TRIM BEZEL AND LID ASSEMBLY WITH POWDER COAT FINISH INSIDE AND OUTSIDE • ANTIQUE COPPER VEIN • TEXTURED BLACK • BRUSHED BRASS* • STAINLESS STEEL* 6.875" OPEN ACCESS .500" REMOVABLE HINGE PERMIT EASY LID EXCHANGE FOR CUSTOM LID CONFIGURATIONS *Solid Brass or Stainless Steel Metal *Finish Available as Special Order 4.375" TOP VIEW 4.75" x 8.5" CUTOUT IN STAGE FLOOR WHEN MOUNTING IN STAGE FLOOR WITHOUT ACE #103BBX BACK BOX 4.500" 4.500" OPEN BACK ACCESS 6.000" .500" SECTION VIEW .375" CABLE WAY SLOT .500" 10.500" 7/8" NOM. CAPTIVE SLOT CLOSURE DROPS INTO BOX WHEN CABLE WAY SLOT IS IN USE 1.875" NOM. NOMINAL OPENING 3.656" 7.187" 8.000" 16 GAUGE (.060" THICK) WELDED STEEL POCKET BODY CONSTRUCTION 1.500" NOMINAL 10.000" CONNECTRIX A FLEXIBLE CONNECTOR AND PANEL SYSTEM Choose Pre-fabricated audio, communications, data, electric, video, and voice connectors and panels, or create custom panels as needed using the CONNECTRIX System of panels and connectors. OPTIONAL BACK BOX WELDED 14 GAUGE (.071” THICK) STEEL 10” X 6.5” X 6” ZINC PLATED (ACE #103BBX BACK BOX) OR OPTIONAL BACK ACCESS COVER 14 GAUGE (.071 THICK) STEEL ZINC PLATED (ACE #23BAC BACK ACCESS COVER - NOT SHOWN) REMOVABLE HINGE PINS PERMIT EASY LID EXCHANGE FOR CUSTOM LID CONFIGURATIONS .500" 4.500" TRIM BEZEL 4.500" FRONT VIEW OPEN BACK ACCESS 6.000" SECTION VIEW 7/8" NOM. 6.000" 1.875" NOM. 3.656" 4.375" 7.187" 8.000" 4.625" 16 GAUGE (.060" THICK) WELDED STEEL POCKET BODY CONSTRUCTION 1.500" NOMINAL 10.000" 6.500" OPTIONAL BACK BOX WELDED 14 GAUGE (.071” THICK) STEEL 10” X 6.5” X FOR 6” ZINC PLATED #103BBX BACK BOX) OR STANDARD POCKET PANELS USE (ACE WITH 123XXXX OPTIONAL BACK ACCESS COVER 14 GAUGE (.071 THICK) STEEL (ACE #23BAC BACK ACCESS COVER - NOT SHOWN) HALF PANEL ZINC PLATED ELECTRICAL PANEL TRIM BEZEL FRONT VIEW PNL-100/PSW-100 SERIES 6.000" APPROVALS PE SERIES DATE DRAWN 4.375" 4.625" CUSTOMER APPROVAL 6.500" FULL POCKET MODEL NUMBERS MODEL # #123CLBK #123CLCV #123LLBK #123SLBK #123SLCV #223CLBR #223SLBR #323CLSS #323SLSS FINISH Electrostatic applied powdercoat MATERIAL 11ga CRS - Lid & Flange 16ga CRS - Pocket Body DESCRIPTION Black Half Pocket w/ Carpet Lid Copper Vein Half Pocket w/ Carpet Lid Black Half Pocket w/ Lid Punched for Lock Black Half Pocket w/ Standard Lid Copper Vein Half Pocket w/ Standard Lid Brass Half Pocket w/ Carpet Lid Brass Half Pocket w/ Standard Lid Stainless Steel Half Pocket w/ Carpet Lid Stainless Steel Half Pocket w/ Standard Lid ITEM 123XXXX DESCRIPTION Half-sized floor pocket to house up to (6) connectors MINI STAGE POCKET 025BK - MINI STAGE POCKET DESCRIPTION The Mini Stage Pocket is a rugged, high-density box with a compact footprint. Designed to conceal up to (4) CONNECTRIX connectors, the two panel positions in the pocket body utilize staggered MP series CONNECTRIX panels. Conceal AC power, audio, switches, etc under the floor surface with the flush mounted bezel and lid that are easily installed into raised floors with or without a back box. CONNECTRIX SYSTEM READY All ACE Stage Pockets are compatible with interchangeable CONNECTRIX System Panels and isolated connector configurations. Designed to maximize space and allow adequate receptacle clearance, CONNECTRIX Panels house a larger number of connections than a standard ganged plate and allow for a customized configuration. For more information on CONNECTRIX Panels see pg. 20 For more information on CONNECTRIX Connectors see pg. 19 ACE STAGE POCKETS Standard Vertical Slant Panel CONNECTOR CAPACITY Super Horizontal Slant Panel Up to (4) connections or (2) electrical outlets x4 (4)) (6) (12) (24) (25) Body Measurement: Floor Cutout Size: Cableway Slot: x2 (50) PANEL OPTIONS FEATURES Lid and Flange Measurement: OR 4.75”L x 7.0”W x 0.187”D 2.688”L x 4.935”W x 2.245”D 2.88” x 5.505” 3/8” x 1.25” (x2) #MP-100 PNL-100 PSW-100 #PE #PNL-120 #PNL-140 Powder Coat Finishes: Special Order Lid & Bezel: Panel Placement: Compatible ACE Panel Series: • Textured Black Decorator (BK) • Antique Coppervein (CV) • Solid Brass (BR) • Stainless Steel (SS) Vertical INCLUDES • (1) Vertical, Slant Panel Style, Stage Pocket • (1) Lid & Trim Bezel • (4) Installation Screws • MP Series OPTIONS DOWNLOAD SPEC SHEET Download DWG & DXF AutoCAD¨ , and PDF Spec Sheets for ALL ACE Stage Pockets at www.acebackstage.com 14 Edison Snap-In Recepticle C-90136 Back Box with A/C Divider pg. 19 pg. 16 ACE BACKSTAGE CO., INC. • 24846 Avenue Rockefeller • Suite 200 • Valencia, CA 91355 • Tel: 661-295-5760 • Fax: 661-295-1122 • www.acebackstage.com 2.750" PROUDLY MADE IN THE U.S.A. www.acebackstage.com VERTICAL SLANT POCKET MINI STAGE MINI POCKET STAGE POCKET 5.350" 7.000" HEAVY DUTY STAINLESS STEEL HINGE AND RIVETS TRIM BEZEL LID ASSEMBLY 11 GA CRS (.120" THICK) MAX LID OPENING 135¼ OPEN ACCESS 4.750" 3/8" x 1-1/4" CABLE EXIT SLOTS CONNECTOR PANELS 2.750" NARROW CLEARANCE FOR SMALLER CONNECTORS WIDER CLEARANCE FOR LARGER CONNECTORS 2.062" 2.245" OPTIONAL #025BBX BACK BOX 5.350" 7.000" 5.560" TRIM BEZEL LID ASSEMBLY 11 GA CRS (.120" THICK) MAX LID OPENING 135¼ CONNECTOR PANELS WIDER CLEARANCE FOR LARGER CONNECTORS 2.245" 3.500" NARROW CLEARANCE FOR SMALLER CONNECTORS 2.688" 2.062" MINI STAGE POCKET BODY 16 GA CRS (.062" THICK) OPTIONAL #025BBX BACK BOX 3.750" 5.560" STANDARD POCKET PANELS FOR USE WITH 025XX #MP-100 #MP-101 #MP-101L #MP-102 #MP-103 #MP-104 #MP-105 #MP-106 #MP-107 #MP-108 #MP-110 #MP-111 3.500" #MP-112 #MP-113 #MP-114 APPROVALS DRAWN CUSTOMER APPROVAL OPTIONAL #025BBX BACK BOX SUPER STAGE POCKET MODEL NUMBERS MODEL # #025BK #025CV #025BR #025SS DESCRIPTION Black Mini Pocket Copper Vein Mini Pocket Brass Mini Pocket Stainless Steel Mini Pocket 2.688" #MP-115 MINI STAGE POCKET BODY 16 GA CRS (.062" THICK) DATE 3.750" OPTIONAL #025BBX BACK BOX FINISH Electrostatic applied powdercoat MATERIAL 11ga CRS Lid & Bezel 16ga CRS Pocket Body ITEM 025XX DESCRIPTION Mini floor pocket to house up to (4) connectors BACK ACCESS COVERS BACK ACCESS COVER DESCRIPTION ACE Back Access Covers are a simple, cost effective option in the sequence of installation in raised floor applications. During the rough-in stage, the BAC may be connected to the conduit through combination knock-outs and left temporarily tacked to the floor joist where the pocket will be installed. All wire can be pulled, and low voltage terminations to connectors/panels can be completed before the finish stage of construction. Accepts accessory brackets for isolation of high and low voltage. #23BAC Back Access Cover for Half Stage Pockets MATERIAL SPEC #22BAC Back Access Cover for Full Stage Pockets UL LISTED MATERIAL: 14 Gauge Sheet Steel CRS (.071 Thick) FINISH: Clear Zinc, Mil Spec ASTM-B633 Type 1, Class 1 FABRICATION: Precision die formed UL Listed compliance Standard 514A in combination with inner floor pocket file FLOOR BOX 44LK #ISO24BAC Isolated Back Access Cover for Double Wide Stage Pockets #22BAC Full Pocket Back Access Cover installation is completed quickly & easily in 3 steps BACK BOXES HALF SIZE BACK BOX MINI SIZE BACK BOX 6.5 ” .0” 10 3. 75 0 ” 50 5.7 ” 6” 3.5” #103BBX #025BBX #025BBX/AC #103BBXW HALF SIZE BACK BOX MINI SIZE BACK BOX Half Size Back Boxes are 14 gauge steel with a protective lid that is discarded when the pocket is fully installed. Clear zinc coated, they mate using a pre-drilled mounting flange and have multiple combination knock-outs. Model #103BBX is UL Compliance Listed. This three gang welded steel box mates perfectly with the ACE Mini Pocket and can be used to isolate AC power and Audio connectivity when ordered as the #025BBX/AC. Model #025BBX is UL Compliance Listed. MODEL NUMBERS ZINC COAT #103BBX MODEL NUMBERS POLYURETHANE JACKET #103BBXW ZINC COAT #025BBX COMPATIBLE WITH: Standard Vertical Slant Panel (4) 16 ((6)) (12) (24) COMPATIBLE WITH: Super Horizontal Slant Panel (25) ISO #025BBX/AC (50) Standard Vertical Slant Panel (4)) (6) (12) (24) Super Horizontal Slant Panel (25) (50) ACE BACKSTAGE CO., INC. • 24846 Avenue Rockefeller • Suite 200 • Valencia, CA 91355 • Tel: 661-295-5760 • Fax: 661-295-1122 • www.acebackstage.com BACK BOXES FULL SIZE BACKBOX 10” DOUBLE WIDE SIZE BACKBOX 10” 10” 18” 8” 6” 6” 12” 8” 12” #102BBX #104BBX #ISO102BBX #102BBXW #ISO104BBX #104BBXW DESCRIPTION Finished in clear zinc for corrosion resistance, these welded steel back boxes mate with standard ACE Stage Pockets using a pre-drilled mounting flange. Available in four different depths, ACE Back Boxes provide 1.5”, 3.5”, 4.5” and 7.5” work clearance underneath the installed stage pocket. Multiple combination knock-outs make these boxes ideal for feed thru or distribution junctions. Models #102BBX and #104BBX are UL Compliance Listed. Polyurethane Encapsulated Back Boxes provide a 1/16” watertight jacket to seal seams, holes, and knock-outs - effectively forming a airtight shield. These boxes provide protection against incursion of moisture, abrasion, chemicals, impact and harsh climates. Back boxes with isolation brackets (ISOXXXBBX) provide galvaneal steel separation between high and low voltage in ACE Stage Pockets. MODEL NUMBERS DEPTH ZINC COAT 6” #102BBX 8” #1028BBX 12” #102DDBBX MODEL NUMBERS ISO POLYURETHANE JACKET #ISO102BBX #102BBXW #ISO1028BBX #1028BBXW #ISO102DDBBX #102DDBBXW DEPTH ZINC COAT 6” #104BBX 8” #1048BBX 12” #104DDBBX COMPATIBLE WITH: Standard Vertical Slant Panel (4) (6) (12) ( ) (24) COMPATIBLE WITH: Super Horizontal Slant Panel (25) ISO POLYURETHANE JACKET #ISO104BBX #104BBXW #ISO1048BBX #1048BBXW #ISO104DDBBX #104DDBBXW Standard Vertical Slant Panel (50) (4) (6) (12) (24) ( Super Horizontal Slant Panel (25) (50) PROTECTIVE LID - DISCARD WHEN INSTALLING POCKET ACE Back Boxes ship with a removable lid (1) to provide protection for the inside of the back box during installation. Once installation of floor is complete, the lid is removed and discarded (2), leaving the inside free of any dirt or concrete and allowing an easy install of the stage pocket (3). 1 2 3 ACE BACKSTAGE CO., INC. • 24846 Avenue Rockefeller • Suite 200 • Valencia, CA 91355 • Tel: 661-295-5760 • Fax: 661-295-1122 • www.acebackstage.com 17 BRACKET KIT ASSEMBLIES BRACKET KIT ASSEMBLIES (#BRK) ACE Bracket Kit Assemblies #BRK102 (A1) and #BRK104 (B1) may be installed in Standard Full Pocket Back Boxes (A2) and Double Wide Pocket Back Boxes (B2). Once Bracket Kit Assemblies have been installed in their respective Back Boxes (A3) and (B3), the resulting products (with #BZ132SLBK and #BZ134SLBK Trim Bezel-Lid Assemblies also added) are the Super Pockets (A4) and Super Double Wide Pockets (B4). #BRK102 #102BBX A1 #BRK102BBX A2 #BRK104 A3 #104BBX B1 A4 #BRK104BBX B2 #132SLBK B3 #134SLBK B4 STAGE POCKET OPTIONS LOCKING LID OPTIONS A B INCREASED CABLE EXIT SIZE OPTION INTERCHANGEABLE LIDS C 0.50” Slot Opening 0.75” Slot Opening 1” Slot Opening Standard Flush Mount Lid Three different types of keyed locks with trim bezels are available for ACE Vertical Slant and Horizontal Panel Pockets (Note: No Locking Lid for Carpet or Mini Pocket): A) Standard Flat Head Screwdriver Lock (screwdriver not included). B) Standard 5/32” Allen Key Wrench (key included). C) Tubular Butterfly Key Lock (key included). Installations requiring exaggerated gauge cables can be accommodated. ACE offers three specialty lid lengths to customize the cable exit space. Each modified lid is supplied with a c-slot closure to be used when the pocket has no cables exiting. A) Modified Lid with 1/2” Slot Opening. B) Modified Lid with 3/4” Slot Opening. C) Modified Lid with 1” Slot Opening. *Standard Cable Exit has a 3/8” Slot Opening Recessed Lid for Carpet Installation Choose from standard flush mount lid or recessed lid for carpet installation. Lids are easily changeable. ELECTRICAL A/C ELECTRIC ISOLATION KIT A B C D Top view of an #A/C ISO KIT installed in a #102BBX Back Box without (1) and with (2) the Full Stage Pocket Body. 1 ELECTRICAL PANELS WITH SWITCHBOX 2 #PE-MP ELECTRICAL PANEL #PE Single Gang Panel for use with all vertical panel style pockets and Super Double Wide Pockets #PE-MP Single Gang Panel for use with pockets installed into ISO Back Boxes and Back Access Covers For use when installing Isolated Back Boxes or Isolated Back Access Covers, the PE-MP Electrical Panel Mount eliminates the switchbox included with the other electrical panels and opens up a larger work area for receptacle termination, while maintaining high and low voltage separation. #FP3E Triple Gang Panel for use with all vertical panel style pockets and Super Double Wide Pockets #ISO24BAC Isolated Back Access Cover *SHOWN INSTALLED WITH PE PANEL #A/C ISO KIT - 1/2” Conduit A.C. Electrical Isolation Kit Includes: • A - (1) #RACO 6712 ............18” Non-Metallic Extra-Flex Conduit • B - (1) #RACO 4732 ............90º Swivel Connector • C - (1) #RACO 4742 ............Straight Connector • D - (1) #GRC COUPLING......Coupling, Female-to-Female 18 #WP-PE Single Gang Panel for use with Table Top Pockets (145xxxx) #ISO102BBX Isolated Back Box *SHOWN WITH RECEPTACLES INSTALLED ACE BACKSTAGE CO., INC. • 24846 Avenue Rockefeller • Suite 200 • Valencia, CA 91355 • Tel: 661-295-5760 • Fax: 661-295-1122 • www.acebackstage.com CONNECTRIX CONNECTORS CONNECTRIX Connectors eliminate the need for a custom cut panel, utilizing our modular system that seamlessly mates each connector into pre-cut holes in CONNECTRIX Panels. Using this system, ACE can ship pocket, wall, or rack panels immediately. No need to wait for a custom cut panel. The CONNECTRIX library offers a wide selection of isolated, adaptor-mounted connectors. CONNECTRIX Connectors arrive installed, per your instruction with either black pop rivets or screws, ready to terminate. XLR 3-Pin Female 3-Pin Female #C-15102 - Solder #C-15100 #C-15119 - Gold #C-15128 - Screw Term 9-PIN 4-Pin Female #C-15105 5-Pin Female #C-15106 6-Pin Female #C-15140 9-Pin Female 9-Pin Female #C-26112 - Solder #C-26110 - Feed Through #C-26117 - Screw Term #C-27110 - Feed Through* #C-27112 - Solder* #C-27117 - Screw Term* 9-Pin Male #C-26113 - Solder #C-27113 - Solder 9-Pin Male #C-26111 - Feed Through #C-27111 - Feed Through* 15-PIN / 25-PIN 3-Pin Male 4-Pin Male #C-15101 - Nylon #C-15139 #C-15103 - Metal #C-15119 - Gold #C-15128 - Screw Term 5-Pin Male #C-15107 6-Pin Male #C-15121 VIDEO S-Video #C-25112 S-Video Value Priced #C-25134 XLR Combo 1/4” #C-25137 15-Pin Female #C-26104 - Feed Through #C-26106 - Solder #C-27106 - Solder* RCA/BNC HD 15 #C-20113 Left & Right RCA #C-25109 Feed Through RCA #C-25133 Feed Through RCA Value Priced #C-25110 HD 15 #C-20113 15-Pin Female #C-26110 - Solder #C-27110 - Solder* 15-Pin Female 15-Pin Male #C-26115 - Screw Term #C-26105 - Feed Through #C-27105 - Feed Through* HD 15 - Value Priced 3.5mm Combo HD15 25-Pin Female #C-26120 #C-26100 - Feed Through #C-25143 #C-26102 - Solder #C-27100 - Feed Through* #C-27102 - Solder* 1/4” COMPUTER HD 15 - Value Priced #C-25143 Feed Through HDMI #C-15142 RCA to BNC #C-25111 Recessed RCA to BNC #C-25132 BNC #C-25101 USB to USB #C-15114 HDMI - Value Priced #C-26122 DVI #C-26121 Recessed BNC #C-25131 USB to USB - Value Priced #C-26118 1/4” Stereo #C-15110 Feed Through Feed Through BNC BNC Value Priced #C-25102 #C-25119 1/4” #C-25127 - Stereo #C-25128 - Mono Combo XLR and 1/4” #C-25137 1/8” RJ45 FireWire #C-15115 RJ45 – Cat 5 Punchdown #C-15109 RJ45 – Cat 5 Punchdown #C-25125 RJ45 – Cat 5 Feed Through #C-15133 RJ45 – Cat 6 Value Priced #C-25136 RJ45 – Cat 5 Value Priced #C-25116 RGBHV (5) BNC #C-28100 - Solder #C-28101 - Feed Through RCA #C-25105 - Black #C-25106 - Red #C-25107 - Yellow #C-25108 - White RCA - Feed Through #C-25138 - Red #C-25139 - White #C-25140 - Yellow #C-25141 - Green #C-25142 - Blue RJ45 – Cat 6 Feed Through #C-15141 CATV FireWire - Value Priced #C-15119 FIBER OPTICS Isolated 3.5mm #C-25100 HD 15 #C-20113 CATV Value Priced #C-25120 Fiber Optic #C-25126 opticalCON #C-15136 Isolated 1/8” #C-25135 HD 15 - Value Priced #C-25143 MISC 3.5mm Combo HD15 #C-26120 POWER RJ11 - Feed Through #C-25114 MIDI #C-25113 32 AMP #C-15137 CATV #C-25103 - Solder #C-25104 - Feed Through Isolated 3.5mm Value Priced #C-25130 speakON #C-15111 - Locking #C-15134 - Screw Term 20 AMP #C-15138 15 AMP #C-90136∆ * - Only compatible with PNL-140 Series ∆ - Only compatible with MP-100 Series ACE BACKSTAGE CO., INC. • 24846 Avenue Rockefeller • Suite 200 • Valencia, CA 91355 • Tel: 661-295-5760 • Fax: 661-295-1122 • www.acebackstage.com 19 CONNECTRIX STAGE POCKET PANELS Used with CONNECTRIX Connectors, these high strength aluminum panels are designed to allow perfect connector clearance and the maximum number of connections in every panel. Because they are machined aluminum alloy (6061-T6) and not punched, they stay flat and undistorted, and are stronger than mild steel panels. The CONNECTRIX style cutout makes it possible to mount any combination of jacks (RJ45, RJ11, multipins, BNC’s, speaker jacks) without a single custom punch. CONNECTRIX POCKET PANELS MINI POCKET PANELS Not Compatible With C-20000 or C-27000 Series Connectors Not Compatible With C-27000 Series Connectors #PNL-100 #PNL-102 #PNL-104 #MP-100 Blank #MP-101 CONNECTRIX Centered #MP-101L CONNECTRIX (L or R) #MP-102 CONNECTRIX #MP-103 CONNECTRIX/S-Video #MP-104 CONNECTRIX/ICC #MP-105 Backloaded #MP-106 Backloaded/ICC #MP-107 Backloaded/ 1/8” or 1/4” #MP-108 Backloaded #MP-110 ICC Centered #MP-111 (L or R) #MP-112 MAAP Module #MP-113 A/C Centered #MP-114 A/C (L or R) #MP-115 15-Pin #PNL-103 #PNL-106 #PNL-105 #PNL-120 #PNL-124 COMPATIBLE WITH: #PNL-128 #PNL-126 Standard Vertical Slant Panel (4)) #PNL-1210 (6) (12) #PNL-1212 #PSW-102 #PSW-103 #PSW-104 #PSW-105 #PSW-106 (4) 20 ((6) (12) (24) #PNL-140 #PNL-1425 COMPATIBLE WITH: Standard Vertical Slant Panel Super Horizontal Slant Panel (25) (50) Compatible with C-15000, C-25000 and C-27000 Series Connectors COMPATIBLE WITH: Standard Vertical Slant Panel (25) SUPER POCKET PANELS Compatible With C-20000 Series Connectors #PSW-100 (24) Super Horizontal Slant Panel (50) (4) (6) (12) (24) Super Horizontal Slant Panel (25) (50) ACE BACKSTAGE CO., INC. • 24846 Avenue Rockefeller • Suite 200 • Valencia, CA 91355 • Tel: 661-295-5760 • Fax: 661-295-1122 • www.acebackstage.com CUSTOMIZED CONNECTRIX PANELS CUSTOM ENGRAVING CUSTOM FABRICATION Rotary engraving on stock CONNECTRIX Panels or CUSTOM Fabricated Panels is fast and easily accomplished on a separate dedicated CNC routing machine. The finished panels show bright aluminum in the engraved characters and do not need to be back filled. Computer Assisted Drafting (CAD) systems feed data to our precision CNC rotary cutting machines to define your panels accurately. Panels are cut and powder-coated, then return to the table for engraving. The finished panels show bright aluminum in the engraved characters and do not need to be back filled. CONNECTRIX Panels are always in stock, can be engraved with company logo information, and ship quickly. Many times ACE ships engraved panels in less than 5 days. Custom Fabricated Panels can be created in sizes as large as 48” x 36” in 1/8” and 1/16” thickness. Each panel is computer drawn and approved by you before being cut, coated, and engraved. Then the coated panel is sent to the assembly bench and populated with specified connectors, switches, nutserts, etc. Once completed the panel is inspected and checked twice before packaging for shipment. For Custom Panel Engraving Forms, Visit acebackstage.com/abc_pages/custom_panels.html CONNECTRIX WALL & RACK PANELS #WP-PE #WP-100 #WP-200 #WP-300 #WP-400 #WP-600 #WP-101 #WP-204 #WP-306 #WP-408 #WP-6012 #WP-102 #WP-206 #WP-308 #WP-4012 #WP-6016 #RPL-110 #RPL-100 #RPL-230 #RPL-200 #RPL-345 #RPL-300 ACE BACKSTAGE CO., INC. • 24846 Avenue Rockefeller • Suite 200 • Valencia, CA 91355 • Tel: 661-295-5760 • Fax: 661-295-1122 • www.acebackstage.com 21 TABLE TOP POCKETS 145SLBK - TABLE TOP POCKET 146SLBK - CONFERENCE POCKET DESCRIPTION DESCRIPTION Absolutely rugged and reliable for day-to-day use, the Table Top Pocket looks great in any boardroom or presentation room setting. Designed specifically for the table, the lid stays open at 3 different intervals allowing you to keep a minimum height profile when in use. Easy to install and secure with reversible installation brackets, this pocket has a unique panel mounting system that allows for 1&2 gang panels or ACE PNL-100/120 CONNECTRIX series panels. This tabletop pocket provides convenient access to A/V and network cables as they pull through to slide in and out of the storage well. As plugs are needed, the low profile lid slides into the pocket out of sight, or can rest flush to the table with cables exiting through the flange slot. The Conference Port is easily installed without the need for intricate routing because the machine-rounded, beveled flange sits virtually flush on your tabletop surface. FEATURES FEATURES Lid and Flange Measurement: Body Measurement: Table Cutout Size: Powder Coat Finishes: Special Order Lid & Bezel: 10.375”L x 8.0”W x 0.125”D 9.0”L x 5.563”W x 2.0”D • Textured Black Decorator (BK) • Solid Brass (BR) Horizontal Compatible ACE Panels Series • PNL-100 • PNL-120 11ga. (.120" thick) Steel, Brass or Stainless Steel Trim Bezel and Lid Body Measurement: 4.0”L x 4.5”W x 3.95”D Table Cutout Size: 4.125”L x 4.875”W Cableway Slot: 2.875”L x 0.375”W • Stainless Steel (SS) Powder Coat Finishes: • PE • FP2E • WP-100 • WP-200 • WP-PE Special Order Lid & Bezel: • Textured Black Decorator (BK) • Solid Brass (BR) • Stainless Steel (SS) 8.0" TOP VIEW TABLE TOP POCKET MODEL NUMBERS MODEL # #145SLBK #245SLBR #345SLSS 5.375”L x 5.875”W x 0.125”D 9.3125” x 6.75” Panel Placement: 10.375" Lid and Flange Measurement: CONFERENCE POCKET MODEL NUMBERS DESCRIPTION Black Table Top Pocket w/ Standard Lid Brass Table Top Pocket w/ Standard Lid Stainless Steel Table Top Pocket w/ Standard Lid MODEL # #146SLBK #246SLBR #346SLSS DESCRIPTION Black Conference Port w/ Standard Lid Brass Conference Port w/ Standard Lid Stainless Steel Conference Port w/ Standard Lid 10.375" 11ga. (.120" thick) Steel, Brass or Stainless Steel Trim Bezel and Lid TOP VIEW 8.0" 8.00" 2.183" 9.00" 10.375" 5.563" SIDE VIEW 22 2.844" Lid Locks open to ACE BACKSTAGE CO., exit INC. • 24846 Avenue Rockefeller • Suite 200 • Valencia, CA 91355 • Tel: 661-295-5760 • Fax: 661-295-1122 • www.acebackstage.com provide a cable and a minimum height profile when in use STAGE MANAGEMENT PRODUCTS This versatile microphone offers the performance of overhead hanging microphones in a totally portable configuration, and is the only WIRELESS microphone of its type in its price range. CHOIR STICK MICROPHONE Manufactured by ACE in partnership with Audio-Technica¨ and Shure¨ to provide solid performance of each Audio-Technica¨ or Shure¨ branded condenser microphone, They are available only at ACE Backstage. CSMs are available in one of two lengths (40”/60”), and with your choice of one interchangeable Audio-Technica¨ or Shure¨ element, ranging from a tight 90* polar pattern to 360* of pick up. Designed with a small diameter gooseneck to permit flexible positioning, all CSMs easily mount onto any standard microphone stand. They will not become unbalanced or tip over even when fully extended. CSM Spec Sheet #CSM-60CW Choir Stick Mics CSM-40/CSM-60 Wireless CSM-40W/CSM-60W CSM Spec Sheet Choir Stick Mics CSM-41/CSM-61 Wireless CSM-41W/CSM-61W Use your smartphone to view Audio-Technica® and Shure® CSM Spec Sheets or visit acebackstage.com/csm MICROPHONE SOFTPOD This simple yet sturdy device was designed to thread on any standard microphone stand and has been updated to accommodate all types of wireless or handheld microphones. The Microphone Softpod is easy to use and is lightweight, which makes it portable and efficient. The soft foam isolates and cushions microphones from each other and minimizes noise when placing or removing microphones. Mic Softpod Noise Isolating Foam 7” The SoftpodÕ s small footprint and lightweight design make it great for small locations or portable systems. 8” Holds up to (6) Microphones #43 MICROPHONE HANGER SLUG The ACE Microphone Hanger Slug allows you to hang almost any microphone from a cable end and point it in any direction. The Microphone Hanger Slug permits a standard microphone stand mount clip to be attached near the end of a hanging cable and the microphone to be clipped in place. The cable is clamped to the slug with a cable tie allowing the cable above to come to a normal relaxed position. This permits the adjustment of the microphone side-to-side movements (yaw) by turning the microphone clip on the slug without twisting the cable above the slug... the microphone will stay exactly where it is pointed. 1. Screw the Slug into the mic clip. 2. #43 Slug threads are pliable, allowing the slug to grip and lock into the clip. 3. Secure the mic cable to slug with the provided cable tie 4. Allow the cable above the slug to twist to a set position 5. Adjust mic clip on slug to point the mic to the correct direction without twisting hanging cable 6. Pivot the clip up/down to position Compatible with most microphone stand mount clips ACE BACKSTAGE CO., INC. • 24846 Avenue Rockefeller • Suite 200 • Valencia, CA 91355 • Tel: 661-295-5760 • Fax: 661-295-1122 • www.acebackstage.com 23 ACE BACKSTAGE CO., INC. 24846 Avenue Rockefeller • Suite 200 Valencia, CA 91355 ACE E CO. STAG BACK CLEAR PUSH COM PUSH DMX12 Presorted Standard U.S. Postage PAID Los Angeles, CA Permit No. 3344 ACE BACKSTAGE CO., INC. STAGE POCKET SYSTEMS Stage Pocket Systems / Panel Fabrication / Spec Fabrication / Stage Management Products CUSTOM DESIGNED CONNECTIVITY ACE can develop custom pockets by utilizing our library of standard components and pocket bodies to design and create pockets that will fit your specific application. Or you can have ACE create a custom pocket from the ground up to meet your specified requirements. From conceptual planning to creation, ACE can build you a custom pocket that will meet all your design expectations. Customize ACE Pockets & Panels to YOUR Needs Download a QR Code Reader on your smartphone to view more ACE Custom Products EXTENDED BEZEL FLOOR BOX CUSTOM BRACKETS & LID FOR OVERSIZED COMPONENTS HEAVY LOAD CAPACITY • NO MINIMUM ORDER • QUICK PRODUCTION • DESIGN ASSISTANCE • CAD PRODUCTION DRAWING PROVIDED