WIN NA ® solutions forms light INTERIOR NOMI OLED STRAIGHT AND CURVE NOMI Wall Sign Winona Lighting, Inc Safety and Installation Instructions TM TABLE OF CONTENTS Tools Required / Electronic Sign Packaging List / Items in Separate Parts Pack 2 Electronic Sign Diagrams 3 Installation Instructions Maintenance and Troubleshooting 4–5 READ AND FOLLOW INSTALLATION INSTRUCTIONS THIS SIGN IS INTENDED TO BE INSTALLED IN ACCORDANCE WITH THE REQUIREMENTS OF ARTICLE 600 OF THE NATIONAL ELECTRICAL CODE AND/OR OTHER APPLICABLE CODES. THIS INCLUDED PROPER GROUNDING AND BONDING OF THE SIGN. 6 TOOLS REQUIRED / ELECTRONIC SIGN PACK AGING LIST / ITEMS IN SEPARATE PARTS PACK NOMI Wall Sign ELECTRONIC SIGN PACKAGING LIST: 1. Electronic Sign Body 2. Mounting Plate with Drivers PARTS NOT INCLUDED: Mounting Fasteners TOOLS REQUIRED: Safety Glasses 5/64” Hex Driver Gloves PARTS INCLUDED: Wire Stripper & Wire Cutter Philips-Head Screwdriver Wire Connectors / Nuts Small Flat-Head Screwdriver NOT INCLUDED (SUPPLIED BY OTHERS): WM MODEL: 4” round or square j-box and dimmer (optional) SWM MODEL: 2x4” j-box and separately installed dimmer (optional) 2 | Winona Lighting ELECTRONIC SIGN DIAGRAMS 2 VERSIONS NOMI Straight and NOMI Curve. Some variations exist between panel configurations and back box size selected at time of order. NOMI STRAIGHT 3) Back Box 5) 8-32 x 1" Mounting Fasteners supplied by others 4) Mounting Plate with Drivers Purple and Grey lines for 0-10V Dimming If not used, the wires are to be capped off. 1) Nomi STR Sconce Electronic Sign Body 4" square or round j-box supplied by others for WM mounting. Use 2"x4" j-box supplied by others for SWM mounting WM Back Box shown (SWM Back Box has (1) 8x32x1" set screw attached to Electronic Sign Body) 2) 8-32 x 1" Set Screws (attached to Electronic Sign Body) Low-Voltage Wire Connections (Using supplied Molex connectors) Line Voltage & Ground wires LUMINAIRE WIRING AND FIXTURE OPERATION CAUTION: CONNECT FIXTURE TO SUPPLY WIRES RATED FOR AT LEAST 60ºC. LOW VOLTAGE WIRING FROM DIMMER TO DRIVER SUPPLIED BY OTHERS. CAUTION: FIXTURE MUST BE CONNECTED TO A NOMINAL 120-277VAC, 50/60 HZ POWER SOURCE ONLY. NOT INCLUDED (SUPPLIED BY OTHERS): 0 -10V Wall Dimmer (optional) and 4” Octagonal or full-size round or square j-box, or double-gang switchbox ELECTRONIC SIGN WIRING AND OPERATION CAUTION: CONNECT ELECTRONIC SIGN TO SUPPLY WIRES RATED FOR AT LEAST 60ºC. LOW VOLTAGE WIRING FROM OPTIONAL 0-10V DIMMER TO DRIVER SUPPLIED BY OTHERS. CAUTION: ELECTRONIC SIGN MUST BE CONNECTED TO A NOMINAL 120VAC, 50/60 HZ POWER SOURCE ONLY. NOMI CURVE NOT INCLUDED (SUPPLIED BY OTHERS): 0 -10V Wall Dimmer (optional) and 4” full-size round or square j-box 3) Back Box 5) 8-32 x 1" Mounting Fasteners supplied by others 4) Mounting Plate with Drivers Purple and Grey lines for 0-10V Dimming If not used, the wires are to be capped off. 1) Nomi CRV Sconce Electronic Sign Body 4" square or round j-box supplied by others for WM mounting. Use 2"x4" j-box supplier by others for SWM mounting WM Back Box shown (SWM Back Box has (1) 8x32x1" set screw attached to electronic sign body) 2) 8-32 x 1" Set Screws (attached to electronic sign body) Low-Voltage Wire Connections (Using supplied Molex connectors) Line Voltage & Ground wires ELECTRONIC SIGN WIRING AND ELECTRONIC SIGN OPERATION CAUTION: CONNECT FIXTURE TO SUPPLY WIRES RATED FOR AT LEAST 60ºC. LOW VOLTAGE WIRING FROM DIMMER TO DRIVER SUPPLIED BY OTHERS. CAUTION: FIXTURE MUST BE CONNECTED TO A NOMINAL 120-277VAC, 50/60 HZ POWER SOURCE ONLY. NOT INCLUDED (SUPPLIED BY OTHERS): 0 -10V Wall Dimmer (optional) and 4” Octagonal or full-size round or square j-box, or double-gang switchbox Winona Lighting | 3 INSTALLATION INSTRUCTIONS INSTALL MOUNTING PLATE: 1. Remove electronic sign components. Check that all parts are included. 2. TURN OFF POWER ON CIRCUIT BREAKER BOX AND ASSURE IT IS OFF! 3. Junction box and appropriate power source/ control wiring must be installed in advance of installation. Select appropriate junction box as per above guidelines. 4. MAKE ELECTRICAL CONNECTIONS AND INSTALL MOUNTING PLATE: Connect 120V AC line to driver AC input, connecting wiring: HOT to BLACK, NEUTRAL to WHITE. Connect AC ground to case ground, GREEN to GREEN. Use installer provided wire connectors. a. For Phase Cut Dimming, the electronic sign will dim through the existing connections. b. For 0-10V Dimming, cut off the wire caps on the PURPLE and GREY wires. Connect 0-10V wall dimmer output to driver dimmer input, matching wire colors: PURPLE to PURPLE and GREY to GREY. c. 4. 4b. 4c. 5. 6a. 4d. Insert wires and wire connectors into the junction box and attach the MOUNTING PLATE with driver onto the junction box using appropriate mounting fasteners. Make sure the driver output with female Molex connector(s) are accessible from the electronic sign side. Please ensure that all other wires are securely inside the junction box and there are NO pinched wires. d. 3. 6b. The MOUNTING PLATE should be level. Use the arrow (pointing UPWARDS) shown on the MOUNTING PLATE as a guide. INSTALL ELECTRONIC SIGN BODY: 5. Locate the SET SCREW(s) on the bottom of the BACK BOX, and retract them using an installer provided 5/64” Hex drive so that the screw tip(s) do not protrude into the BACK BOX. DO NOT retract the screws entirely. 6. Bring the electronic sign body close to the junction-box. Make connection(s) between male and female Molex connectors (1-3 connections depending on model). 4 | Winona Lighting INSTALLATION INSTRUCTIONS a. To engage connectors, align the male and female connector(s) as shown and push to engage. 7. 7. 8. Should you need to disengage the Molex connector(s): Identify the small gap between the male and female sides. Insert a small flathead screwdriver into the gap and twist. The male and female sides should come apart. b. 7. Connectors are interchangeable but all connectors must be engaged. Install the ELECTRONIC SIGN BODY onto the MOUNTING PLATE by first tilting the top of the electronic sign towards the wall. Hook the inside top edge of the BACK BOX onto the top of the MOUNTING PLATE. Swing the bottom of the electronic sign towards the wall while maintaining contact between the inside top edge of the BACK BOX and the MOUNTING PLATE. Please ensure that all wires are securely inside the BACK BOX and there are NO pinched wires. Note: the size of the BACK BOX varies by electronic sign model. 9. NOMI 0-10V DIMM ING 0-10V DIMMER SUPPLIED BY "OTHERS" GREY - HOT AC LINE 120VOLT NEUTRAL EARTH GROUND BLACK WHITE DRIVER GREEN RED RED BLACK BLACK CHASSIS GROUND MOLEX CONNECTOR(S) 0-10V DIMMER SUPPLIED BY "OTHERS" EARTH GROUND HOT NOMI 0-10V DIMM ING AC LINE 120VOLT WALL SWITCH BLACK NOMI NON DIMM ING WHITE DRIVER GREEN RED RED BLACK THESE WIRES ARE TO BE CAPPED OFF BLACK CHASSIS GROUND MOLEX CONNECTOR(S) BLACK NEUTRAL WHITE EARTH GROUND DRIVER RED RED BLACK BLACK GREEN 0-10V DIMMER SUPPLIED BY "OTHERS" MOLEX CONNECTOR(S) GREEN RED RED BLACK BLACK HOT AC LINE 120VOLT GREY - DRIVER PHASE CUT DIMMER SUPPLIED BY "OTHERS" BLACK NEUTRAL WHITE EARTH GROUND CHASSIS GROUND GREEN DRIVER PURPLE + WHITE THESE WIRES ARE TO BE CAPPED OFF RED RED BLACK BLACK ELECTRONIC SIGN EARTH GROUND BLACK NOMI PHASE CUT DIMM ING ELECTRONIC SIGN GREY HOT NEUTRAL PURPLE + CHASSIS GROUND AC LINE 120VOLT ELECTRONIC SIGN NEUTRAL GREY - HOT AC LINE 120VOLT WIRING DIAGRAMS: ELECTRONIC SIGN GREY - Turn on electricity at fuse or circuit breaker box. Return to the unit and check for correct operation. If a dimmer was installed, please ensure that the dimmer is operating properly. PURPLE + 9. LUMINAIRE When the BACK BOX is flush against the wall and the electronic sign is hanging on the MOUNTING PLATE, secure the electronic sign by fully engaging electronic sign the SET SCREW on the bottom of the BACK BOX using an installer provided 5/64” Hex driver (depending on the model, unit may require two set screws). Verify that the electronic sign is securely attached by making sure the body does not wiggle. NOMI 0-10V DIMM ING PURPLE + 8. PURPLE + NOTE: the size of the BACK BOX varies by electronic sign model. MOLEX CONNECTOR(S) CHASSIS GROUND MOLEX CONNECTOR(S) Winona Lighting | 5 MAINTENANCE & TROUBLESHOOTING COMPATIBLE DIMMER LIST: NOTE: Consult Winona Lighting before using any dimmer NOT listed below. 0-10V DIMMING SOLUTIONS: ACUITY CONTROLS MODEL NUMBERS: nLight nPP16D nLight nEPP5D nLight nPODMD nLight nPODM2PD nLight nPODM4PD nLight nPODMRD nLight nPODD nLight nCM PDT 10 ADC nLight nCM 6 ADC nLight nCM PDT 9 ADC nLight nCM 10 ADC nLight nCM 9 ADC nLight nCM ADC nLight nPANEL nLight nIO LEDG LC nLight nIO EZ PH nLight nIO D nLight nPS 80 EZ nLight nEPS 60 IO EZ LC XPoint Wireless RL1 DSI Xcella DIO Fresco LMPX4L Synergy SYPM 8L Synergy ISD BC 120/277L LUTRON MODEL NUMBERS: Lutron Nova NFTV Lutron Nova NTSTV-DV Lutron Diva DVTV Lutron Nova NTSTV-DV Lutron Diva DVSTV LEVITON MODEL NUMBERS: Leviton Illumatech IP710-DL PHASE CUT DIMMER: nLIGHT MODEL NUMBERS: nSP5 PCD ELV 120 ELECTRONIC SIGN MAINTENANCE: REPLACEMENT PART NUMBERS: To clean, wipe OLED panels with a soft damp nonabrasive cloth, and use gloves. • Rubbing alcohol may be used for cleaning purposes. • DO NOT use abrasive materials such as scouring pads or powders, steel wool or abrasive paper. • DO NOT use any detergents, acids or chemical agents. • DO NOT attempt to remove OLED panels for cleaning purposes. NOMI Straight • Rectangular Front OLED Panel OLEDR1 • Rectangular Rear OLED Panel OLEDR2 NOMI Curve • Rectangular Front/Rear OLEDB1 TROUBLESHOOTING GUIDE: If this electronic sign fails to operate properly, use the guide below to diagnose and correct the problem. • Make sure that the OLED panels are not damaged. • Verify that electronic sign is properly wired. • Verify that electronic sign is correctly grounded. • Verify that line voltage at the electronic sign is correct (120V). One Lithonia Way, Conyers, GA 30012 770.922.9000 acuitybrands.com Manufactured by Winona Lighting, division of Acuity Brands Lighting, Inc. © 2015 Acuity Brands Lighting, Inc. All Rights Reserved. 8/15 WL_1601