nomitm oled - Acuity Brands

advertisement
WIN NA
®
solutions
forms
light
INTERIOR
NOMI OLED
NOMI Wall Sconce
Winona Lighting, Inc
Safety and Installation Instructions
TM
STRAIGHT AND CURVE
TABLE OF CONTENTS
Tools Required / Fixture Packaging List / Items in Separate Parts Pack
2
Fixture Diagrams
3
Installation Instructions
Maintenance and Troubleshooting
4–5
READ AND FOLLOW INSTALLATION INSTRUCTIONS
FIXTURE MUST BE WIRED AND INSTALLED PER LOCAL AND NATIONAL ELECTRIC CODES
6
TOOLS REQUIRED / FIXTURE PACK AGING LIST / ITEMS IN SEPARATE PARTS PACK
NOMI Wall Sconce
FIXTURE PACKAGING LIST:
1. Luminaire Body
2. Mounting Plate with Drivers
PARTS NOT INCLUDED:
Mounting Fasteners
TOOLS REQUIRED:
Safety Glasses
5/64” Hex Driver
Gloves
PARTS INCLUDED:
Wire Stripper & Wire Cutter
Philips-Head Screwdriver
Wire Connectors / Nuts
Small Flat-Head Screwdriver
NOT INCLUDED (SUPPLIED BY OTHERS):
WM MODEL: 4” round or square j-box and dimmer (optional)
SWM MODEL: 2x4” j-box and separately installed dimmer (optional)
2 | Winona Lighting
FIXTURE DIAGRAMS
2 VERSIONS
NOMI Straight and NOMI Curve. Some variations
exist between panel configurations and back box size
selected at time of order.
NOMI STRAIGHT
3) Back Box
5) 8-32 x 1" Mounting Fasteners
supplied by others
4) Mounting Plate with Drivers
Purple and Grey lines for 0-10V Dimming
If not used, the wires are to be capped off.
1) Nomi STR Sconce Electronic Sign Body
4" square or round
j-box supplied by others
for WM mounting. Use
2"x4" j-box supplied by
others for SWM mounting
WM Back Box shown (SWM Back Box has
(1) 8x32x1" set screw attached to Electronic Sign Body)
2) 8-32 x 1" Set Screws (attached to Electronic Sign Body)
Low-Voltage Wire Connections
(Using supplied Molex connectors)
Line Voltage & Ground wires
LUMINAIRE WIRING AND FIXTURE OPERATION CAUTION: CONNECT FIXTURE TO SUPPLY WIRES RATED FOR AT LEAST 60ºC.
LOW VOLTAGE WIRING FROM DIMMER TO DRIVER SUPPLIED BY OTHERS.
CAUTION: FIXTURE MUST BE CONNECTED TO A NOMINAL 120-277VAC, 50/60 HZ POWER SOURCE ONLY.
NOT INCLUDED (SUPPLIED BY OTHERS): 0 -10V Wall Dimmer (optional) and 4” Octagonal or full-size round or square j-box, or double-gang switchbox
LUMINAIRE WIRING AND FIXTURE OPERATION CAUTION:
CONNECT FIXTURE TO SUPPLY WIRES RATED FOR AT LEAST 60ºC.
LOW VOLTAGE WIRING FROM OPTIONAL 0-10V DIMMER TO DRIVER
SUPPLIED BY OTHERS. CAUTION: FIXTURE MUST BE CONNECTED
TO A NOMINAL 120VAC, 50/60 HZ POWER SOURCE ONLY.
NOMI CURVE
3) Back Box
5) 8-32 x 1" Mounting Fasteners
supplied by others
4) Mounting Plate with Drivers
Purple and Grey lines for 0-10V Dimming
If not used, the wires are to be capped off.
1) Nomi CRV Sconce Electronic Sign Body
4" square or round
j-box supplied by others
for WM mounting. Use
2"x4" j-box supplier by
others for SWM mounting
WM Back Box shown (SWM Back Box has
(1) 8x32x1" set screw attached to electronic sign body)
2) 8-32 x 1" Set Screws (attached to electronic sign body)
Low-Voltage Wire Connections
(Using supplied Molex connectors)
Line Voltage & Ground wires
ELECTRONIC SIGN WIRING AND ELECTRONIC SIGN OPERATION CAUTION: CONNECT FIXTURE TO SUPPLY WIRES RATED FOR AT LEAST 60ºC.
LOW VOLTAGE WIRING FROM DIMMER TO DRIVER SUPPLIED BY OTHERS.
CAUTION: FIXTURE MUST BE CONNECTED TO A NOMINAL 120-277VAC, 50/60 HZ POWER SOURCE ONLY.
NOT INCLUDED (SUPPLIED BY OTHERS): 0 -10V Wall Dimmer (optional) and 4” Octagonal or full-size round or square j-box, or double-gang switchbox
Winona Lighting | 3
INSTALLATION INSTRUCTIONS
INSTALL MOUNTING PLATE:
1.
Remove fixture components. Check that all
parts are included.
2.
TURN OFF POWER ON CIRCUIT BREAKER
BOX AND ASSURE IT IS OFF!
3.
Junction box and appropriate power source/
control wiring must be installed in advance of
installation. Select appropriate junction box as
per above guidelines.
4.
MAKE ELECTRICAL CONNECTIONS AND
INSTALL MOUNTING PLATE: Connect 120V
AC line to driver AC input, connecting wiring:
HOT to BLACK, NEUTRAL to WHITE. Connect
AC ground to case ground, GREEN to GREEN.
Use installer provided wire connectors.
a.
3.
4.
4b.
4c.
5.
6a.
4d.
For Phase Cut Dimming, the fixture will dim
through the existing connections.
b. For 0-10V Dimming, cut off the wire caps on
the PURPLE and GREY wires. Connect 0-10V
wall dimmer output to driver dimmer input,
matching wire colors: PURPLE to PURPLE
and GREY to GREY.
c.
Insert wires and wire connectors into the
junction box and attach the MOUNTING
PLATE with driver onto the junction box
using appropriate mounting fasteners.
Make sure the driver output with female
Molex connector(s) are accessible from the
fixture side. Please ensure that all other wires
are securely inside the junction box and
there are NO pinched wires
6b.
d. The MOUNTING PLATE should be level. Use
the arrow (pointing UPWARDS) shown on the
MOUNTING PLATE as a guide.
INSTALL LUMINAIRE BODY:
5.
Locate the SET SCREW(s) on the bottom of the BACK BOX, and retract them using an installer provided 5/64” Hex drive so that
the screw tip(s) do not protrude into the BACK BOX. DO NOT retract the screws entirely.
6.
Bring the luminaire body close to the junction-box. Make connection(s) between male and female Molex connectors
(1-3 connections depending on model).
4 | Winona Lighting
INSTALLATION INSTRUCTIONS
a.
To engage connectors, align the male and
female connector(s) as shown and push to
engage.
7.
7.
8.
Should you need to disengage the Molex
connector(s): Identify the small gap between
the male and female sides. Insert a small flathead screwdriver into the gap and twist. The
male and female sides should come apart.
b. Connectors are interchangeable but all
connectors must be engaged.
Note: the size of the BACK BOX varies by fixture model.
9.
NOMI 0-10V DIMM ING
0-10V DIMMER
SUPPLIED BY "OTHERS"
HOT
BLACK
RED
RED
BLACK
BLACK
When the BACK BOX is flush against the wall
and the luminaire is hanging on the MOUNTING
PLATE, secure the luminaire by fully engaging
the
electronic sign
SET SCREW on the bottom of the BACK BOX using an installer provided 5/64” Hex driver (depending on the model, unit may
require two set screws). Verify that the luminaire is securely attached by making sure the
body
not wiggle.
NOMI
0-10V does
DIMM ING
AC LINE
120VOLT
NEUTRAL
EARTH GROUND
WHITE
DRIVER
GREEN
CHASSIS GROUND
0-10V DIMMER
SUPPLIED BY "OTHERS"
HOT
AC LINE
120VOLT
WHITE
DRIVER
GREEN
RED
RED
THESE WIRES
ARE TO BE CAPPED
BLACK OFF
BLACK
WALL SWITCH
CHASSIS GROUND
NEUTRAL
MOLEX CONNECTOR(S)
RED
BLACK
WHITE
EARTH GROUND
BLACK
DRIVER
RED
BLACK
GREEN
ELECTRONIC SIGN
EARTH GROUND
NOMI
NON DIMM ING
BLACK
ELECTRONIC SIGN
WIRING DIAGRAMS:
NEUTRAL
GREY -
HOT
AC LINE
120VOLT
PURPLE +
GREY -
Turn on electricity at fuse or circuit breaker box. Return to the unit and check for correct operation. If a dimmer was installed,
please ensure that the dimmer is operating properly.
PURPLE +
NOMI 0-10V DIMM ING
MOLEX CONNECTOR(S)
CHASSIS GROUND
NEUTRAL
EARTH GROUND
WHITE
GREEN
CHASSIS GROUND
DRIVER
RED
RED
BLACK
BLACK
MOLEX CONNECTOR(S)
HOT
AC LINE
120VOLT
GREY -
BLACK
THESE WIRES
ARE TO BE CAPPED OFF
ELECTRONIC SIGN
HOT
AC LINE
120VOLT
NOMI PHASE CUT DIMM ING
PURPLE +
GREY -
0-10V DIMMER
SUPPLIED BY "OTHERS"
PHASE CUT DIMMER
SUPPLIED BY "OTHERS"
BLACK
NEUTRAL
WHITE
EARTH GROUND
GREEN
CHASSIS GROUND
DRIVER
RED
RED
BLACK
BLACK
ELECTRONIC SIGN
9.
MOLEX CONNECTOR(S)
PURPLE +
8.
GREY -
NOTE: the size of the BACK BOX varies by fixture model.
LUMINAIRE
Install the LUMINAIRE BODY onto the
MOUNTING PLATE by first tilting the top of
the luminaire towards the wall. Hook the inside
top edge of the BACK BOX onto the top of the
MOUNTING PLATE. Swing the bottom of the
luminaire towards the wall while maintaining
contact between the inside top edge of the BACK
BOX and the MOUNTING PLATE. Please ensure
that all wires are securely inside the BACK BOX
and there are NO pinched wires.
PURPLE +
7.
MOLEX CONNECTOR(S)
Winona Lighting | 5
MAINTENANCE & TROUBLESHOOTING
COMPATIBLE DIMMER LIST:
NOTE: Consult Winona Lighting before using any dimmer NOT listed below.
0-10V DIMMING SOLUTIONS:
ACUITY CONTROLS MODEL NUMBERS:
LUTRON MODEL NUMBERS:
nLight nPP16D
nLight nEPP5D
nLight nPODMD
nLight nPODM2PD
nLight nPODM4PD
nLight nPODMRD
nLight nPODD
nLight nCM PDT 10 ADC
nLight nCM 6 ADC
nLight nCM PDT 9 ADC
nLight nCM 10 ADC
nLight nCM 9 ADC
nLight nCM ADC
nLight nPANEL
nLight nIO LEDG LC
nLight nIO EZ PH
nLight nIO D
nLight nPS 80 EZ
nLight nEPS 60 IO EZ LC
XPoint Wireless RL1 DSI
Xcella DIO
Fresco LMPX4L
Synergy SYPM 8L
Synergy ISD BC 120/277L
Lutron Nova NFTV
Lutron Nova NTSTV-DV
Lutron Diva DVTV
Lutron Nova NTSTV-DV
Lutron Diva DVSTV
LEVITON MODEL NUMBERS:
Leviton Illumatech IP710-DL
PHASE CUT DIMMER:
nLIGHT MODEL NUMBERS:
nSP5 PCD ELV 120
LUMINAIRE MAINTENANCE:
REPLACEMENT PART NUMBERS:
To clean, wipe OLED panels with a soft damp nonabrasive cloth, and use gloves.
• Rubbing alcohol may be used for cleaning
purposes.
• DO NOT use abrasive materials such as scouring
pads or powders, steel wool or abrasive paper.
• DO NOT use any detergents, acids or chemical
agents.
• DO NOT attempt to remove OLED panels for
cleaning purposes.
NOMI Straight
• Rectangular Front OLED Panel OLEDR1
• Rectangular Rear OLED Panel OLEDR2
NOMI Curve
• Rectangular Front/Rear OLEDB1
TROUBLESHOOTING GUIDE:
If this fixture fails to operate properly, use the guide
below to diagnose and correct the problem.
• Make sure that the OLED panels are not damaged.
• Verify that fixture is properly wired.
• Verify that fixture is correctly grounded.
• Verify that line voltage at the fixture is correct (120V).
One Lithonia Way, Conyers, GA 30012
770.922.9000
acuitybrands.com
Manufactured by Winona Lighting, division of Acuity Brands Lighting, Inc.
For further assistance or information, contact
Winona Lighting at 800.328.5291.
© 2015 Acuity Brands Lighting, Inc. All Rights Reserved.
8/15
WL_1079
Download