Series
Horns, Strobes,
and Horn/Strobes
Horn/Strobe
with Standard Plate
A Division of Pittway
3825 Ohio Avenue, St. Charles, IL 60174
1-800-SENSOR2 (736-7672), Fax 630-377-6495
http://www.systemsensor.com
Strobe
with Small Footprint Plate
Horn
with Standard Plate
Features
•
•
•
•
•
24 volt strobe models: 15, 15/75, 30, 75 and 110 candela
12 volt strobe models: 15 and 15/75 candela
Horn models operate on 12 and 24 volts
Low current draw: reductions as high as 45%
Two field selectable/reversible horn tones
– 3000 Hz Interrupted
– Electromechanical
• Field selectable/reversible high-low dBA output on horn
(low output on 24 volt models only)
– 101 peak dBA @ 10 ft. high output*
– 96 peak dBA @ 10 ft. low output*
• Field selectable/reversible temp 3 pattern or non-temp 3
continuous pattern on horn
• Horn/strobe can be wired either in tandem or independently
• Universal mounting plate included with each unit
• One screw mounting of strobe and horn/strobe to mounting
plate
• SpectrAlert strobe and horn/strobe take up zero room in the
back box.
• Single gang mounting without the use of a mounting plate
(horn model only)
• Self-contained screw covers
• Aesthetically pleasing design
• Synchronize horn and strobe with Sync•Circuit™ module
• Silence horn on horn/strobe over a single pair of wires using
Sync•Circuit module
* Sound output varies with tone and output options selected; sound
levels based upon anechoic room measurements.
Specifications
Walk test: SpectrAlert horn/strobe and horn only work on “walk
tests” with time durations of 4 seconds or greater.
Input terminals:
12 to 18 AWG
Dimensions
Strobe and horn/strobe
with universal plate:
5″ × 55/8″ × 215/16″
Strobe and horn/strobe
with small footprint plate:
33/8″ × 55/8″ × 25/16″
Horn with universal
mounting plate:
5″ × 55/8″ × 15/16″
Horn without
mounting plate:
215/16″ × 55/16″ × 15/16″
Weight, horn only:
7.2 oz.
Weight, strobe and
horn/strobe:
8.8 oz.
4″ × 4″ × 11/2″ or
2″ × 4″ × 17/8″ standard boxes
Indoor operating temperature: 32° to 120° F (0° to 49° C)
Weatherproof (horn and horn/strobes)
operating temperature:
32° to 150° F (0° to 66° C)
(outdoor strobe only):
-40° F to 158° F (-40° C to 70° C)
Voltages:
12 or 24 VDC and FWR unfiltered
Operating voltage range*:
12 V, 10.5–17 V; 24 V, 20–30 V
Operating voltage range* (with
Sync•Circuit module, MDL): 12 V, 11–17; 24 V, 21–30 V
Mounting:
* These products should be operated within their rated voltage range; UL does, however, test
functional integrity to –20% and +10% of manufacturer’s stated ranges.
APPROVED
For listing information see “Notes” on bottom of page 6.)
General Description
System Sensor SpectrAlert Series strobes, horns, and combination horn/
strobes are UL listed for primary signaling in life safety systems and meet
ADA public mode visible signaling requirements.
SpectrAlert products can be connected to the alarm indicating circuit of
a fire alarm control panel and are compatible with DC line supervision. The
SpectrAlert product line mounts to standard back boxes with the use of a
universal mounting plate included with each unit. An optional small
footprint mounting plate fits to a single gang box. An accessory back box
skirt gives a cosmetic finish to a 4″ × 4″ × 11/2″ or a 2″ × 4″ × 17/8″ surface
mounted back box. All strobe and horn/strobe mounting options require
only one screw attachment of product to plate.
These products are designed for 12 and 24 VDC and full wave rectified
unfiltered power. Full wave rectified operation requires more current than
DC operation. For detailed current draw information, consult the table
below. The horn/strobe combination products are factory assembled with
jumper wires for in-tandem operation. For independent wiring of horn and
strobe, remove jumper wires. When wired for independent operation, the
strobe will continue to run while the horn can be silenced. However, the
strobe must be running for horn to operate.
selectable features are accomplished with the use of pins and jumpers
located on the back of each SpectrAlert horn and horn/strobe. An accessory
module is not needed to make these field selections. The horn on horn/
strobe models will operate on a coded power supply. The horn only model
designed for coded power supplies (HC12/24) will also operate on a coded
power supply.
Strobes
The ADA compliant SpectrAlert strobes are electronic visible warning
signals that flash at 1 Hz over their operating voltage range. These products
are available in 24 volt models at 15, 15/75, 75 and 110 candela intensities
and in 12 volt models at 15 and 15/75 candela intensities. SpectrAlert
products feature dramatic reductions in current requirements.
Sync•Circuit Module
The Sync•Circuit Module is available for the synchronization of strobes and
horns and can synchronize two Style Y (class B) circuits or one Style Z
(class A) circuit. The module can also generate a synchronized temp 3 tone
for System Sensor’s Multi-Alert™ and PA400 horn products.* The
synchronization module allows the SpectrAlert horns on combination horn/
strobes to be silenced on 2-wire systems. SpectrAlert’s Sync•Circuit Module
can be daisy chained for multiple zone synchronization. The Module shall
not operate on a coded power supply.
Horn
The SpectrAlert Series horns and horn/strobes provide two different field
selectable/reversible tones, a high-low field selectable/reversible sound
output setting (low setting on 24 volt models only) and a field selectable/
reversible temp 3 pattern or non-temporal continuous pattern. These field
*For Multi-Alert and PA400: Strobes must be wired to a continuous source
of power (non-coded power supply).
SpectrAlert Current Draw Table
Strobe Only:
AVERAGE CURRENT (mA)
12V Models
24V Models
10.5V
12V
17V
20V
24V
30V
Candela
15
15/75
30
75
110
DC
FWR
133 159
168 182
NA NA
NA NA
NA NA
DC FWR
DC
114 157 81
142 171 99
NA NA NA
NA NA NA
NA NA NA
FWR
DC
FWR
PEAK CURRENT (mA)
12V Models
24V Models
10.5V
12V
17V
20V
24V
30V
DC FWR
DC
FWR
128 50
61
43
38
60
150 56
65
49
NA 78 84 67
NA 145 170 123
NA 169 220 140
DC
FWR
DC FWR
460
64 44 62 490
82 58 72 NA
159 102 141 NA
191 115 174 NA
460
520
NA
NA
NA
450
490
NA
NA
NA
60
460
520
NA
NA
NA
DC
DC FWR
DC
FWR
DC
420 480 135 204 135 208
460 480 150 199 150 207
NA NA 183 201 183 219
NA NA 350 440 340 460
NA NA 460 560 450 570
135
150
183
330
420
185
198
216
480
620
80 108 92
76 104 88
NA NA NA
NA NA NA
NA NA NA
High/Low
Volume
High
Low
3000 Hz High
Interrupt.
Low
Tone
Electromech.
Low
3000 Hz High
Interrupt.
Low
Temp
/Non
Temp
Non
Temp
Non
Temp
Non
Temp
Non
DC FWR DC FWR DC
10
10
NA
NA
11
11
NA
NA
11
16
NA
NA
13
17
NA
NA
10
10
NA
NA
11
11
NA
NA
10
19
NA
NA
11
21
NA
NA
14
14
NA
NA
16
14
NA
NA
FWR DC FWR DC FWR DC
14
25
NA
NA
16
28
NA
NA
19
17
11
12
24
19
14
13
21
29
12
16
26
34
14
18
25
23
13
14
28
27
17
16
18
34
13
19
23
39
15
21
29
30
17
17
37
35
21
22
FWR
26
42
15
24
33
45
19
25
Temp
/Non
Temp
Non
Temp
Non
Temp
Non
Temp
Non
High/Low
Volume
High
Low
3000 Hz High
Interrupt.
Low
Page 2
Temp
/Non
Temp
Non
Temp
Non
Temp
Non
Temp
Non
Tone
Electromech.
High/Low
Volume
High
Low
3000 Hz High
Interrupt.
Low
FWR
DC FWR
124
126
NA
NA
NA
DC
FWR
DC
FWR
140 190 97 129
160 185 97 135
NA NA 97 129
NA NA 190 240
NA NA 190 230
DC FWR
116
116
116
230
220
152
164
152
280
290
Temp
/Non
Temp
Non
Temp
Non
Temp
Non
Temp
Non
AVERAGE CURRENT (mA)
24V Models
20V
24V
30V
DC
FWR
DC FWR
DC
FWR
97
95
89
90
102
97
92
91
105
113
96
98
108
116
96
100
92
90
80
81
95
94
84
83
87
88
75
75
95
93
79
80
98
114
87
96
105
117
91
97
100
116
95
101
105
121
97
103
Horn/Strobe 75 cd:
AVERAGE CURRENT (mA)
12V Models
24V Models
10.5V
12V
17V
20V
24V
30V
DC FWR DC FWR DC
FWR DC FWR DC FWR DC
FWR
143
143
NA
NA
144
144
NA
NA
142
142
NA
NA
144
146
NA
NA
87
103
76
85
94
106
80
86
170
170
NA
NA
172
173
NA
NA
124
124
NA
NA
125
125
NA
NA
167
167
NA
NA
168
168
NA
NA
95
95
NA
NA
97
95
NA
NA
69
67
61
62
74
69
64
63
82
90
73
77
87
95
75
79
68
66
56
57
71
70
60
59
78
94
73
79
83
99
75
81
67
68
55
55
75
73
59
60
Tone
Electromech.
High/Low
Volume
High
Low
3000 Hz High
Interrupt.
Low
Temp
/Non
Temp
Non
Temp
Non
Temp
Non
Temp
Non
AVERAGE CURRENT (mA)
24V Models
20V
24V
30V
DC
FWR
DC FWR
DC
FWR
164
163
156
157
169
164
159
158
191
188
182
182
196
192
184
188
148
146
136
137
151
150
140
139
131
132
119
119
139
137
123
124
167
169
156
157
174
177
160
162
167
169
162
162
172
175
164
163
Horn/Strobe 110 cd:
Horn/Strobe 1575 cd:
Tone
Electromech.
FWR
AVERAGE CURRENT (mA)
12V Models
24V Models
10.5V
12V
17V
20V
24V
30V
Horn/Strobe 15 cd:
High/Low
Volume
High
DC
Horn/Strobe 30 cd:
Horn Only:
Tone
Electromech.
FWR
IN RUSH CURRENT (mA)
12V Models
24V Models
10.5V
12V
17V
20V
24V
30V
AVERAGE CURRENT (mA)
12V Models
24V Models
10.5V
12V
17V
20V
24V
30V
DC
FWR
DC FWR
DC
FWR
DC
FWR
178
178
NA
NA
179
179
NA
NA
193
193
NA
NA
195
196
NA
NA
152
152
NA
NA
152
152
NA
NA
113
113
NA
NA
115
113
NA
NA
164
164
NA
NA
166
168
NA
NA
75
73
67
68
80
75
70
69
86
94
77
81
91
99
79
83
181
181
NA
NA
183
183
NA
NA
DC FWR
DC
FWR
74 82 73
72 98 74
62 77 61
63 83 61
77 87 81
76 103 79
66 79 65
65 85 66
88
104
77
86
95
107
81
87
Tone
Electromech.
High/Low
Volume
High
Low
3000 Hz High
Interrupt.
Low
Temp
/Non
Temp
Non
Temp
Non
Temp
Non
Temp
Non
AVERAGE CURRENT (mA)
24V Models
20V
24V
30V
DC
FWR
DC FWR
DC
FWR
188
186
180
181
193
188
183
182
241
238
232
232
246
242
234
232
165
163
153
154
168
167
157
156
144
145
132
132
152
150
136
137
200
202
189
190
207
210
193
195
209
211
204
204
214
217
206
205
DC
FWR
147
147
147
290
290
198
211
198
380
370
Engineering Specifications
General
SpectrAlert horns, strobes and horn/strobes shall be capable of
mounting to a standard 4″ × 4″ × 11/2″ back box or a single gang 2″ × 4″
× 17/8″ back box using the universal mounting plate included with each
SpectrAlert product. Also, SpectrAlert products, when used in
conjunction with the accessory Sync•Circuit Module, shall be powered
from a non-coded power supply and shall operate on 12 or 24 volts. 12
volt rated devices shall have an operating voltage range of 10.5 - 17
volts. 24 volt rated devices shall have an operating voltage range of 20 30 volts. SpectrAlert products shall have an operating temperature of 32
to 120° F and operate from a regulated DC or full wave rectified,
unfiltered power supply.
Horn
Horn shall be a System Sensor SpectrAlert model _________ capable of
operating at 12 and 24 volts. Horn shall be listed to UL 464 for fire
protective signaling systems. The horn shall have two tone options, two
audibility options (at 24 volts) and the option to switch between a
temporal 3 pattern and a non-temporal continuous pattern. The horn
only model designed for coded power supplies (HC12/24) shall operate
on a coded power supply.
Strobe
Strobe shall be a System Sensor SpectrAlert model _________ listed to
UL 1971 and be approved for fire protective service. The strobe shall be
wired as a primary signaling notification appliance and comply with the
Americans with Disabilities Act requirements for visible signaling
appliances, flashing at 1 Hz over the strobe’s entire operating voltage
range. The strobe light shall consist of a xenon flash tube and
associated lens/reflector system.
Horn/Strobe Combination
Horn/strobe shall be a System Sensor SpectrAlert model _________
listed to UL 1971 and UL 464 and shall be approved for fire protective
service. Horn/strobe shall be wired as a primary signaling notification
appliance and comply with the Americans with Disabilities Act
requirements for visible signaling appliances, flashing at 1 Hz over its
entire operating voltage range. The strobe light shall consist of a xenon
flash tube and associated lens/reflector system. The horn shall have
two tone options, two audibility options (at 24 volts) and the option to
switch between a temporal 3 pattern and a non-temporal continuous
pattern. Strobes shall be powered independently of the sounder with
the removal of factory installed jumper wires. The horn on horn/strobe
models shall operate on a coded or non-coded power supply.
Module
Module shall be a System Sensor Sync•Circuit model _________ listed
to UL 464 and shall be approved for fire protective service. The module
shall synchronize SpectrAlert strobes at 1 Hz and horns at temporal 3.
Also, the module shall silence the horns on horn/strobe models, while
operating the strobes, over a single pair of wires. The module shall be
capable of mounting to a 411/16″ × 411/16″ × 21/8″ back box and shall
control two Style Y (class B) or one Style Z (class A) circuit. Module
shall be capable of multiple zone synchronization by daisy chaining
multiple modules together and re-synchronizing each other along the
chain. The Module shall not operate on a coded power supply.
SpectrAlert Dimensions
215/16″
33/8″
15
55/16″
55/8″
15/16″
25/16″
Horn/Strobe with Small Footprint Mounting Plate
(same dimensions for strobe only)
Horn Only
51/4″
215/16″
2″
55/8″
55/16″
51/4″
5″
25/16″
Horn/Strobe with Universal Mounting Plate
(same dimensions for strobe only)
Page 3
/16″
Sync•Circuit Module
SpectrAlert Mounting Diagrams
2″ back box
BBS
4″ back box
Horn Direct Mount
4″ back box
D-MP
(included with
each product)
Horn Surface Mount with Accessory
Back Box Skirt
2″ back box
S-MP
Horn with Universal Mounting Plate (included with
each product)
4″ back box
D-MP
(included with
each product)
Strobe or Horn/Strobe with Accessory
Small Footprint Mounting Plate
Strobe or Horn/Strobe with Universal
Mounting Plate (included with each product)
4″ back box
BBS
411/16″ × 411/16″ × 21/8″ back box
Strobe or Horn/Strobe Surface Mount
with Accessory Back Box Skirt
Sync•Circuit Module Direct Mount
Page 4
SpectrAlert Wiring Diagrams
TANDEM OPERATION
INDEPENDENT OPERATION
HORN AND STROBE
HORN/STROBE COMBO
HORNS
FACTORY INSTALLED
JUMPER WIRES REMOVED
TO NEXT
DEVICE OR
EOL
TO NEXT
HORN OR
EOL
(–)
(+)
(–)
(+)
FACTORY INSTALLED
JUMPERS
(+)
(–)
(+)
STROBES
FROM:
(–) FACP, MODULE
OR PREVIOUS
(+) DEVICE
TO NEXT
STROBE OR
EOL
FROM:
FACP, MODULE
OR PREVIOUS
DEVICE
Break wire as shown for
supervision of connection.
DO NOT allow stripped wire
leads to extend beyond switch
housing. DO NOT loop wires.
(–)
(+)
(+)
(+)
H
O
R
N
(+)
HORN
HORN/STROBE
STROBE ONLY
(+)
(+)
(+)
(–)
E
O
L
(–)
(–)
(+)
NOTE: STROBES MUST
BE POWERED CONTINUOUSLY
FOR HORN OPERATION.
(–)
E
O
L
(–)
(–)
FOUR WIRE SYSTEM
COMBO MODELS
WIRED FOR INDEPENDENT
OPERATION
(HORN CAN BE TURNED OFF
AT THE PANEL WHILE STROBES
CONTINUE TO OPERATE)
C
O
M
B
O
TWO WIRE SYSTEM
ANY MIX OF MODELS
WIRED FOR TANDEM
OPERATION
(+)
(–)
(–)
H
O
R
N
(–)
Horns Silenced Over Two-Wire Circuit
(+)
S
T
R
O
B
E
(–)
(+)
S
T
R
O
B
E
E
O
L
(–)
Temp 3 Coding of Multi-Alert and
PA400 Sounders
1. Any mix of Horn/Strobes or Strobe only devices is acceptable
2. Horn control connects to interruptible power source
Note: Strobes must be powered from non-coded supply
MASTER MODULE
FACP #1
(+)
NAC1
(–)
(+)
NAC2
(–)
(+)
NAC3
(–)
EOL
}
}
}
}
(+)
(–)
HORN
CONTROL
ZONE 1
OUT
(+)
(–)
ZONE 1
IN
ZONE 2
OUT
(+)
(–)
ZONE 2
IN
SYNC
ERROR
(+)
(–)
SLAVE
IN
SLAVE
OUT
}
}
}
}
)+(
)–(
TO NEXT
SPECTRALERT
DEVICE OR
EOL
)+(
)–(
)+(
)–(
FACP
TO NEXT
SPECTRALERT
DEVICE OR
EOL
)+(
)–(
}
}
}
}
HORN
CONTROL
ZONE 1
OUT
NAC1
(+)
(–)
ZONE 1
IN
ZONE 2
OUT
NAC2
(+)
(–)
ZONE 2
IN
SYNC
ERROR
(+)
(–)
SLAVE
IN
SLAVE
OUT
}
}
}
}
)+(
)–(
MA12/24D
OR PA400
HORN
ONLY
TO NEXT
DEVICE OR
EOL
MA12/24D
OR PA400
HORN
ONLY
TO NEXT
DEVICE OR
EOL
)+(
)–(
)+(
)–(
)+(
)–(
TEMP JUMPER OFF
TEMP. JUMPER ON
Horns will be Temporal
coded and in sync.
SLAVE MODULE
FACP #2
(+)
NAC1
(–)
(+)
NAC2
(–)
}
}
}
}
)+(
)–(
HORN
CONTROL
ZONE 1
OUT
(+)
(–)
ZONE 1
IN
ZONE 2
OUT
(+)
(–)
ZONE 2
IN
SYNC
ERROR
(+)
(–)
SLAVE
IN
SLAVE
OUT
TEMP JUMPER OFF
}
}
}
}
)+(
)–(
TO NEXT
SPECTRALERT
DEVICE OR
EOL
)+(
)–(
)+(
)–(
TO NEXT
SPECTRALERT
DEVICE OR
EOL
)+(
)–(
All SpectrAlert horns,
horn/strobes, and strobes
will operate in sync.
Sound Output Guide (dBA)
Temporal Low Tone
Electromechanical
3000 Hz Interrupted
High Tone Electromechanical
3000 Hz Interrupted
NonLow Tone Electromechanical
Temporal
3000 Hz Interrupted
High Tone Electromechanical
3000 Hz Interrupted
Page 5
UL Reverberant Room dBA@ volts DC
10.5
12
17
20
24
30
NA
NA
NA
75
75
79
NA
NA
NA
75
79
79
75
75
79
82
82
82
75
75
79
82
85
85
NA
NA
79
79
NA
NA
79
82
NA
NA
85
85
79
82
85
88
82
82
88
88
85
85
88
88
Anechoic
10.5
NA
NA
94
94
NA
NA
94
93
Room
12
NA
NA
95
95
Peak
17
NA
NA
98
98
NA
NA
95
95
NA
NA
98
98
dBA @10 ft./volts DC
20
24
30
94
96
98
94
96
98
100
101
102
100
101
102
94
94
100
100
96
96
101
101
98
98
102
102
SpectrAlert Ordering Information
All weatherproof models must use weatherproof back box model WBB.
Canada
Latin America
Strobes
Canada
Latin America
Horns
Canada
Sync•Circuit Module
Canada
Small Footprint Mounting
Plate for Single Gang Only
Surface Mount Back Box Skirt
Universal Mounting
Plate (replacement)
Weatherproof Back Box
White
P1215
P121575
P2415
P241575
P2430
P2475
P24110
P241575K (weatherproof)
P2475K (weatherproof)
P24110K (weatherproof)
P2415A
P241575A
P2475A
P24110A
P241575KA (weatherproof)
P2475KA (weatherproof)
P24110KA (weatherproof)
P241575F (FUEGO)
Avg. mA*
Avg. mA*
@ Nom. VDC @ Nom. FWR**
Voltage
Candela
P1215W
P121575W
P2415W
P241575W
P2430W
P2475W
P24110W
–
–
–
P2415WA
P241575WA
P2475WA
P24110WA
–
–
–
12
12
24
24
24
24
24
24
24
24
24
24
24
24
24
24
24
24
15
15/75
15
15/75
30
75
110
15/75
75
110
15
15/75
75
110
15/75
75
110
15/75
124
152
68
74
92
148
165
74
148
165
68
74
148
165
74
148
165
74
167
181
78
82
100
167
209
82
167
209
78
82
167
207
82
167
207
82
S1215
S121575
S2415
S241575
S2430
S2475
S24110
S241575K (weatherproof)
S2475K (weatherproof)
S24110K (weatherproof)
S2415A
S241575A
S2475A
S24110A
S241575KA (weatherproof)
S2475KA (weatherproof)
S24110KA (weatherproof)
S241575F (FUEGO)
S1215W
S121575W
S2415W
S241575W
S2430W
S2475W
S24110W
–
–
–
S2415WA
S241575WA
S2475WA
S24110WA
–
–
–
12
12
24
24
24
24
24
24
24
24
24
24
24
24
24
24
24
24
15
15/75
15
15/75
30
75
110
15/75
75
110
15
15/75
75
110
15/75
75
110
15/75
114
142
43
49
67
123
140
49
123
140
43
49
123
140
49
123
140
49
157
171
60
64
82
159
191
60
159
191
60
64
149
191
64
149
191
64
H12/24
H12/24K (weatherproof)
HC12/24 (for coded power)
HC12/24K
(for coded power, weatherproof)
H12/24A
H12/24KA (weatherproof)
HC12/24A (for coded power)
H12/24W
–
HC12/24W (for coded power)
12/24
12/24
12/24
NA
NA
NA
10 / 25
10 / 25
10 / 25
10 / 18
10 / 18
10 / 18
–
H12/24WA
–
HC12/24WA (for coded power)
12/24
12/24
12/24
12/24
NA
NA
NA
NA
10 / 25
10 / 25
10 / 25
10 / 25
10 / 18
10 / 18
10 / 18
10 / 18
MDL
MDLA
MDLW
MDLWA
12/24
12/24
NA
NA
16
16
24
24
S-MP
BBS
S-MPW
BBSW
NA
NA
NA
NA
NA
NA
NA
NA
D-MP
WBB
D-MPW
–
NA
NA
NA
NA
NA
NA
NA
NA
Notes:
Agency Listings – Indoor models: UL, ULC, FM, CSFM, MEA. Weatherproof models: UL, CSFM, MEA, ULC.
All SpectrAlert products are designed for wall mount only.
Installation of less than 75 candela strobes may be permissible under the equivalent facilitation clause of the ADAAG (Sec. 2.2). However, it is the responsibility of the
person or entity designing the fire alarm system to determine the acceptability of less than 75 candela strobes.
All 15/75 candela strobes or horn/strobes are recommended for 20′ × 20′ rooms or less.
* Horn and horn/strobe current draws assume horn is set at temp 3, electromechanical tone and high audibility.
** FWR = Full Wave Rectified
System Sensor Worldwide Manufacturing & Distribution
Canada:
Telephone: 905-812-0767
Fax: 905-812-0771
The Far East:
Telephone: 852-2191-9003
Fax: 852-2736-6580
Italy:
Telephone: 39-40-9490-111
Fax: 39-40-382137
China:
Telephone: 852-2191-9003
Fax: 852-2736-6580
India:
Telefax: 91-022-8202564
Singapore:
Telephone: 65-273-2230
Fax: 65-273-2610
Page 6
The United Kingdom:
Telephone: 44-1403-276500
Fax: 44-1403-276501
This document is not intended to be used for installation purposes.
System Sensor reserves the right to change product specifications at anytime.
A05-936-05
#346/8-98/CPI/10K
Horn / Strobes
Red