1. Voltage varies between countries. The local power supply must be compatible with the technical data shown
on the data label before the fan is connected to power source.
2. The plug must be inserted to an earthed socket, which complies with the Safety Regulation of the local
authority.
3. For safety purpose, the wall fan is to be installed so that the blades are more than 2.3 metres above the floor.
4. For smooth oscillation of fans, a slack of 0.4m should be left when securing power cord from motor to stand
tube or wall tube.
5. For safety purpose, the recommended maximum height for the PSE63 is 1.5 metre. (Care must be taken
during adjusting the height of the standing fan)
−
−
−
Grip the rubber handle at the top of the inner tube
Using the allen key provided unfasten the screws and adjust the fan to the desirable height
Tighten the screw and put the allen key back in its pocket at the rubber handle
6. The fan is fitted with a 3-speed, on & off rotary switch to adjust air velocity (1-low, 2-medium, 3-high and
stop/off fan operation).
7. Always turn off the power at the power point and remove plug when maintenance or cleaning is carried out.
Failing to do so may cause electric shock or injury as the fan may activate suddenly.
8. When cleaning is carried out
−
−
−
−
−
−
Turn off the power at the power point and remove the plug
Remove the front guard (if the guard cannot be removed easily, use tools)
Remove the blade from the motor by loosening the blade fixing screw
Remove the rear guard
Remove dirt with a cloth moistened with lukewarm water or a household neutral detergent and wipe
dry after cleaning
When re-assembling, use the reverse order of disassembling
9. For the best performance and safety, the fan must not be used when:
a
b
c
Temperature is lower than -15°C or higher than +40°C
Humidity (at 25°C) is exceeding 90%
In a corrosive environment, such as factory producing corrosive chemical.
10. Never try to disassemble, service or modify the fan. This may cause fire, abnormal activation, electric shock
or injury. For servicing, contact the store where you purchased the fan.
11. Do not operate the fan without the blade and the guard installed. Doing so may cause injury.
12. Do not damage, forcibly bend, twist, pull, put a heavy object on the supply cord. Doing so may cause electric
shock or a short circuit if used whilst damaged. If the supply cord is damaged, it must be replaced by a new
cord at the manufacturer or its service agent.
13. The fan motor is fitted with a thermal protection device.
If a fault occurs, the fan may start and stop intermittently without warning. This may occur due to irregular
power supply or excessively high ambient temperature the fault is obvious, return fan to the supplier.
WARRANTY:
Fantech Pty Ltd warrants products of its manufacture when not misused or neglected to be free of defects in workmanship and/or
materials. Our obligation under this warranty is limited to repairing or exchanging F.O.B. factory, any part, assembly or portion found
to be defective within one year from the date of commissioning but not to exceed eighteen (18) months from date of shipment from
our factory.
The Company assumes no responsibility for labour costs involved in the removal of defective parts, installation of new parts or
related service charges.
The Company shall have the option of requiring the return of the defective part (transportation prepaid by the Buyer) to establish
the claim.
Warranty will be void if installation is not carried out by qualified personnel in accordance with these instructions and good trade
practice.
Fully detailed warranty conditions are contained in Fantech’s Standard Conditions of Trading.
Part No.: INST-PEDESTAL
INSTALLATION PROCEDURE FOR PEDESTAL FAN
(Refer reverse side for additional assembly and safety instructions)
S1
Insert outer standing tube into cast iron base and fasten it with the four bolts and spring washers provided.
Insert inner standing tube into outer tube.
S2
Remove set screw from the motor support bracket, place the motor onto the support bracket and fasten the
set screw. (Please refer to the set screw sequence above)
S3
Using the four (M6) screws provided secure rear safety guard onto face of motor, insert fan blade onto the
rotor shaft and secure by firmly tightening the screw using the allen key provided.
INSTALLATION PROCEDURE FOR WALL MOUNTING FAN
W1
Secure the iron base onto the wall. Insert the bent pipe, adjust the height of the wall fan (at least 2.3 metre
from the ground floor) and secure by the screws provided
W2
Repeat S2 and S3.
Part No: INST-PEDESTAL