1 of 2
Installation Instructions
Impression LED Adjustable
CAUTION: TO REDUCE RISK OF SHOCK, TURN OFF electrical supply BEFORE Installing / SERVICING THE FIXTURES.
WARNING: LAMP WILL BE HOT. ALLOW LAMP TO COOL BEFORE ATTEMPTING TO REPLACE LAMP.
IMPORTANT: Read all
(Do Not Use Bare Hand To Replace Lamp In Fixture)
instructions before starting
installation. Keep instructions WARNING: Fixture must be installed in accordance of National Electrical Code (NEC) and/or any local codes.
for future reference.
Failure to do so may result in serious injury and/or damage to the fixture.
caution read before installation
Important safety instructions
–– Read all installation instructions before installing. It is important to save these instructions.
–– Observe and follow all label information and instructions regarding dry, damp and wet location listings, proper lamp type and wattage, warnings of installation near combustible
materials and/or insulation.
–– Turn off power at circuit breaker before attempting to install or perform all maintenance.
–– Be sure to connect ground wire to prevent electric shock or other potential hazards.
–– The product must be installed in a manner consistent with the intended use and in compliance with the national electrical and local codes.
–– Do not block the trim aperture as this may cause unsafe operating conditions.
–– Warning: risk of fire. Most dwellings built before 1985 have supply wire rated for 60°C. Consult a qualified electrician before installation. The fixture must be connected with
supply wire rated for at least 75°C.
Warning: Use only Intense Lighting trims listed for use with this fixture. Use of trims other than those listed by Intense Lighting is a violation of n.E.C 110-3(b) and voids all
warranties. Use proper lamps and do not exceed maximum wattages as indicated on the housing label for each trim. Exceeding maximum wattage lamp will void all warranties.
HOUSING INSTALLATION:
1. Mount fixture housing according to ceiling type.
• Universal mounting bracket has slot openings for C-channel, flat bar, and 1/2” EMT;
secure to joist or grid using fasteners or wire. C-channel hangers are recommended
for T-Bar ceilings, install with notches facing down to engage T-Bar grid.
• Bar hangers are supplied for sheet rock installations.
Junction box
1/2” EMT slots
C-Channel slots
Flat bar hanger slots
Universal mounting
bracket
C-Channel
T-Bar notch
Bar hangers
1/2” EMT
ELECTRICAL CONNECTIONS:
1. Make electrical connections through desired knock
out for conduit or romex® cable. Use only UL listed
connectors.
2. Connect black wire from fixture to black (HOT)
supply wire, white wire from fixture to white
(NEUTRAL) supply wire and connect the ground
from fixture to green (GROUND) supply wire. Use
UL listed connectors or wire nuts to make the
connections (provided by others).
3. Close and lock junction box door ensuring all wire
connections and wire are contained within.
Junction box
door
Metal Conduit
Knockouts
Recessed L/M-05242013 P-1
Intense Lighting | 2861. E La Palma Ave. | Anaheim, CA 92806 | Phone: 1.800.961.5321 | Fax: 1.800.961.5322 | www.intenselighting.com
Note: Instructions and dimensions subject to change without notice.
2 of 2
Installation Instructions
Impression LED Adjustable
0° - 40° VERTICAL AIMING ADJUSTMENT:
1. Insert screwdriver in vertical adjustment socket.
2. Turn to desired vertical aiming position.
Vertical locking
hex screw
Vertical
adjustment socket
TRIM INSTALLATION:
1. Locate front torsion spring slot on housing and
trim.
Front torsion
spring slot
VERTICAL LOCKING:
1. Insert hex driver (included) into hex screw.
2. Tighten hex screw to lock vertical position.
Hex driver
(included)
TRIMLESS INSTALLATION:
1. Screw perforated mud plate to housing with screws
(included).
2. Apply joint compound over perforated mud plate
and feather out accordingly.
HORIZONTAL AIMING ADJUSTMENT:
1. Turn to desired horizontal aiming position.
2. Insert screwdriver in horizontal locking socket and
lock the position.
Horizontal locking
socket
SERVICING:
1. Remove trim from housing.
2. Adjust vertical orientation to downlight position.
3. Loosen (3) fasteners in keyhole slots.
4. Rotate fixture clockwise and slide out of housing.
5. Disconnect fixture at connector.
Front torsion
spring
Loosen
fasteners
Disconnect
fixture
2. Squeeze torsion springs together and insert into
slots.
3. Push trim into housing ensuring the trim is flush
to the ceiling.
4. Once all fixtures have been installed, power at the
breaker can be restored.
3. Locate orientation slot on housing and line up with
orientation slot on trim. (Used to orientate trim to
adjustment mechanism)
4. Push trim into housing ensuring the trim is flush
to the ceiling.
5. Once all fixtures have been installed, power at the
breaker can be restored.
Orientation
Slot
Orientation
Bracket
Keyhole
slots
Recessed L/M-05242013 P-2
Intense Lighting | 2861. E La Palma Ave. | Anaheim, CA 92806 | Phone: 1.800.961.5321 | Fax: 1.800.961.5322 | www.intenselighting.com
Note: Instructions and dimensions subject to change without notice.