EMS
Emergency Micro Power Inverters
The EMS Series is designed to provide 20- to
55- Watts of emergency power to incandescent,
fluorescent, and/or LED fixtures. The EMS unit
provides clean, sinusoidal AC output power allowing
it to be remotely mounted up to 1,000 feet away from
the controlled fixture(s).
Unlike a ballast fluorescent emergency pack, the
EMS provides power to the input side of the fixture,
(including the ballast) eliminating any chance of
incompatibility. EMS Series models are available
for surface, recessed or ceiling T-Grid mounting if
required. All EMS systems will provide emergency
power output for a minimum of 90 minutes.
FEATURES
•
For powering incandescent, fluorescent, and LED
fixtures
•
True sinusoidal AC pulse width modulated (PWM)
design provides clean 60 Hz. emergency output
•
Universal 120/277 VAC, 60Hz. input/output
•
Unit capacities of 20 to 55 Watts
•
“Soft Start” design reduces fixture inrush current
•
Surface, recessed or T-Grid mount models
•
Lumen output from fixture is 100% of nominal
•
•
Maintenance-free Lead-Calcium and premium grade
Nickel-Cadmium battery models offered
Unique design eliminates compatibility problems
with LED drivers as well as fluorescent ballasts
•
Control panel with momentary test switch, AC-ON,
Charge-ON and Inverter-ON LED indicators
•
Normally ON, Normally OFF, or switched outputs
•
Battery circuit fuse protected
•
Temperature compensated, dual-mode charger
includes low voltage disconnect feature to provide
protection against battery deep discharge
•
•
•
Reverse battery and AC lockout protection
Knockouts in back
White powder coat finish
2572 Metropolitan Drive, Trevose, PA 19053 USA
TEL: (800) 872 0879 • FAX:(215) 244 4208 • www.evenlite.com
Project name:
Approved By:
Catalog No:
Type No:
Tufflite S 6 & 12EMS
Volt,- Emergency
36-130 WattMicro
MetalPower
Series
Emergency Light
Inverters
FEATURES
Specifications
Mounting
INPUT
• Two fully adjustable, top mounted Par 36 style
•• Surface
Mount:Surface
models
are designed
for and
mounting
Low voltage
cut-offmount
prevents
battery
damage
to ensures
walls by means
of
keyhole
slots
provided
in
the
back
of
the unit
positive charge acceptance following an
housing.
lighting heads in high
are
Voltage:
120 orimpact
277VACthermoplastic
± 10%
supplied as standard.
Lighting
Frequency:
120 or
277VAC ±heads
10% are available
with a variety of lamp
types
and wattage’s
Protection:
Provided
by Service
Panel, Rated 20A max.
extended discharge
• Recess Mount:Recess models provide recess mounting holes on
• both
Brownout
sensing
assures emergency operation
sides of the
enclosure.
• Accommodates up to four lighting heads (2 top,
OUTPUT
during periods of low line voltage
• T-Grid Mount:Housing design allows simple drop-in installation
2
side)
Standard
units
are
supplied
with
two
top
• between
Shortt-grid
circuit
battery
runs.
Safety protection
wires (supplied by others) are required
Voltage:
120 or 277VAC (60Hz)
mounted
heads
for
attachment
to
building
structure.
Efficiency Rating:
98% at full rate load (line)
• ARRA Compliant for Level 1
•
20
gauge
steel
cabinet
with(digitally
universal
knock-out
Waveform:
Sinusoidal
controlled,
PWM design)
• Listed to/UL
924, meets NFPA 101 Life Safety Code,
Warranty
Listing
pattern± 5% during
inbattery
a durable
white0-100%
powder
Static mounting
Voltage:
discharge.
NFPA 70-NEC and OSHA requirements
linear load
• Unit: 3 years limited coverage against defects in materials and
(other colors
available to order)
coat
from warranty
date of shipment.
• workmanship
3 Year limited
Output
Frequencies:
Hz ± and
0.3Hzconduit
during emergency
cycle
• Key
hole mounting60slots
knockouts
are
Outputprovided
Distortion:for additional
Less than
3% THD (linear
load)
• Battery: Lead-Acid 3 years, one full and two pro-rated
mounting
possibilities
Operating
Characteristics
Nickel cadmium
5 years
one full and four pro-rated
Transfer Time:
Less than 1.0 second
•
Choice
of
maintenance
free
sealed
Lead
Calcium
or
Wattage
Load Power Factor Range: 0.44 Lead to 0.44 Lag
• All models are UL924 Listed and meet NFPA 101 Life Safety Code,
Model
Voltage
Nickel
Cadmium
batteries
90 min
2 hrs
3 hrs
4 hrs
NEC, OSHA, Local and State Codes. Optional T-Grid
models
are
Minimum Loading:
0% of rated system capacity
6
36
27
18
12
S2E36
plenum
rated.
• Premium,
current limited “Pulse
Output
Protection: fully automatic
Inverter fuse
6
42
31
21
15
S2N42
Switching”
charger
provides
ideal charge conditions
Power Consumtion (max): 9W
6
54
36
27
18
S2N54
for optimum battery performance and life
6
60
45
30
22
S2E60
Housing
• Self Test / Self Diagnostic monitoring available
6
72
54
36
27
S2E72
• • Heavy
duty steel
cabinet has atest
white
powder
coatdual
finish providing
External
Momentary
switch
and
6
90
67
45
33
S2N90
scratch
and corrosion
diagnostic
LED resistance.
indicator displays AC presence
6
120
90
60
45
S2E120
and Hi-Charge status
12
130
97
65
48
S4N130
SYSTEM SPECIFICATIONS
NiCad Batteries deliver the same capacity per wattage as above for listed models
• Field selectable 120 or 277 VAC input
6&12 Volt models deliver the same capacity per wattage as above for listed models
• Model
Line-latch
prevents
of (°C)
batteryDC Input Current
System
Weight unnecessary
Battery Type discharge
Temp. Range
Input Current
Thermal Output in BTUs
Lbs.
(VDC)
during installation,
loads will not illuminate until
120VAC (max)
277VAC (max)
Standby
Emergency
after application of utility power
EMS-32
14.0
ORDERING
GUIDE
EMS-55
18.0
Lead-Calc
20-30°
3.4
0.34A
0.15A
7
32
Lead-Calc
20-30°
5.7
0.54A
0.23A
7
47
EMS-20
11.0
NiCad
0-50°
2.1
0.25A
0.11A
31
22
EMS-35
12.0
NiCad
0-50°
0.37A
0.16A
31
35
S2E36
Model weights show include installed
Model batteries
*System
Lead Calcium Battery
90 Minute Capacity
ORDERING
GUIDE
S2E36
6 Volt – 36 Watts
S2E60
S2E72
S2E100
S2E120
Model
6 Volt – 60 Watts
6 Volt – 72 Watts
6 Volt – 100 Watts
6 VoltVA
– 120
Watts
Rating
S4E36
EMS
S4E60
S4E72
S4E120
S4E140
12 Volt – 3632Watts
12 Volt – 60 Watts
12 Volt – 7255Watts
12 Volt – 120
20Watts
12 Volt – 140 Watts
EMS
Nickel Cadmium Battery
90 Minute Capacity
S2N42
S2N54
S2N90
6 Volt – 42 Watts
6 Volt – 54 Watts
6 Volt – 90 Watts
3.8
No. of Top Mounted
Lighting Heads
0
1
2
3
4
S4N42
12 Volt – 42Input/Output
Watts
Battery Type
S4N90
12 Volt – 90 Watts
120/277
S4N130LC 12 Volt – 130V3
Watts
35
No Lighting Heads
Single Lighting Head
Double Lighting Heads
Three Lighting Heads
Four Lighting Heads
Options
S
Surface Mount
LC
RE
Recess Mount
NiCad
TB
T-Grid Mount
NiCad
*System weights show include installed batteries
Lighting Heads
Options
W69
SD
V
A
TD
Standard 6 volt unit
9 Watt Lamp Head
W129 Standard 12 volt unit
9 Watt Lamp Head
W
Wedge Base Tungsten
C
Capsule Halogen
S
PAR36 Tungsten
H
PAR36 Halogen
For additional Lampheads
refer to Lamp Selection
Guide Data sheet RH
Note: Total lamp wattage must
not exceed unit 90 minute
capacity rating
Self Test / Self Diagnostic
Voltmeter
Ammeter
15 Minute Time Delay (Specify
AC Voltage)
C
3 ft. Conductor Cord & Plug
MH Metal Lamp Heads PAR 36
(type S & H lamps only)
MR MR16 Lampheads (12 Volt
only, see lamp selection
guide)
WG6 Wire Guard
Example: S2E36-2-W69-SD
3161 Metropolitan
State Road Drive,
• Bensalem,
PA 19053
19020 USA
USA
2572
Trevose, PA
Tel: (800) 872-0879 • Fax: (215) 244-4208
TEL:
(800)
872
0879
•
FAX:(215)
244
4208
•
www.evenlite.com
www.evenlite.com
TL-S 1/14
Tufflite S 6 & 12EMS
Volt,- Emergency
36-130 WattMicro
MetalPower
Series
Emergency Light
Inverters
FEATURES
Batteries
and Charger
Improved Aesthetics
BATTERY
• Two fully adjustable, top mounted Par 36 style
The
output design
eliminates
voltage
• EMS
Lowsystem’s
voltagesinusoidal
cut-off AC
prevents
battery
damage
anddrop
and proximity
concerns.
This
allows
added
flexibility
in
installation
ensures positive charge acceptance following an
location as EMS units can be installed hundreds of feet from the units
extended discharge
they power. This means EMS units to be located conveniently out of sight
in
or utilitysensing
rooms without
interrupting
architectural
aesthetics.
operation
• closets
Brownout
assures
emergency
lighting
in high Free
impact
thermoplastic
Battery:
Choiceheads
of Maintenance
Sealed
Lead Calcium orare
Sealed
Nickel-Cadmium
supplied as standard. Lighting heads are available
with
a variety
of for
lamp
types
and wattage’s
Battery
Voltage:
12VDC
all EMS
models
• Accommodates
up toOther
four runtimes
lightingavailable,
heads (2
top, factory.
Runtime:
90 minutes standard.
consult
2 side)
Standard
units
are supplied
two top
Battery:
Low Voltage
Battery
Disconnect
protects with
the battery
from being
mounted
severely
damaged heads
by deep discharge during prolonged power failures.
DC
and Short
Protection
provided by
a DC input fuse.
• Overload
20 gauge
steel Circuit
cabinet
with universal
knock-out
Batterymounting
voltage (VDC)
12
pattern
in a durable white powder
(other colors available to order)
coat
CHARGER
• Key hole mounting slots and conduit knockouts are
Charger Type: Fully automatic, temperature compensated, dual-mode
provided for additional mounting possibilities
charger
• Choice of maintenance free sealed Lead Calcium or
Power Consumption: 9W max (All models)
Nickel Cadmium batteries
Recharge Duty Cycle: Meets UL924 requirements
• Premium, fully automatic current limited “Pulse
Controls:Momentary test switch, AC-On, Charge-On and inverter-On
Switching”
LED indicator
lights charger provides ideal charge conditions
for optimum battery performance and life
Safety Circuitry: AC lockout prevents battery discharge prior to initial
• power-up.
Self Test / Self Diagnostic monitoring available
unit
Brownout
Protection
automatically
unitdual
to emergency mode
• External
Momentary
testswitches
switchtheand
when utility
voltage
is
significantly
reduced.
diagnostic LED indicator displays AC presence
and Hi-Charge status
ENVIRONMENTAL
• Field selectable 120 or 277 VAC input
Altitude:< 10,000 feet (3,000m) above sea level without derating.
• Line-latch prevents unnecessary discharge of battery
Operating Temperature Range:
during installation, loads will not illuminate until
Lead-Calcium Models: 68°F to 86°F (20°C to 30°C)
after application
of utility
to 122°Fpower
(0°C to 50°C)
Nickel-Cadmium
Models: 32°F
NOTE:
Optimum system
performance between 20°C (68°F) and 30°C
ORDERING
GUIDE
(86°F); temperatures outside of the range will affect battery performance
andS2E36
life.
Relative Humidity:95% non-condensing
Model
Lead Calcium Battery
OPERATION
No. of Top Mounted
Lighting Heads
Model
during periods of low line voltage
EMS System Advantages
• Short circuit battery protection
Compared to traditional discrete emergency lighting units, the EMS
• ARRA
Compliant
for Level 1 from a single power source
Series
provides
emergency illumination
resulting in lower maintenance overhead and routine testing expenses.
• Listed to UL 924, meets NFPA 101 Life Safety Code,
EMS units lower installation costs by powering existing lighting fixtures
NFPA
70-NEC
and
OSHA
requirements
during
emergencies.
And
because
connected
fixtures are driven at full
brilliance,
they
providewarranty
far superior egress lighting and deliver improved
• 3 Year
limited
occupant safety
Operating Characteristics
Dimensions
Wattage
Model
Voltage
90 min
Standard Surface
6
36
S2E36 Mount Housings
3 hrs
4 hrs
27
18
12
S2N42
6
42
31
21
15
S2N54
6
54
36
27
18
S2E60
6
60
45
30
22
36
27
45
33
S2E72
6
72
S2N90
6
90
7-3/8"
54
67
S2E120
6
120
90
S4N130
12
130
97
14-3/4"
60
4-3/8"
65
(Models
45
3-3/8"
48(Models
EMS-32
EMS-32
NiCad Batteries deliver the same capacity per wattage as above
for listed models
& EMS-55)
& EMS-55)
6&12 Volt models deliver the same capacity per wattage as above for listed models
Recessed Mount Housings
8-7/8"
Lighting Heads
Nickel Cadmium Battery
90 Minute Capacity
16-1/4"
0 No Lighting Heads
W69 Standard 6 volt unit
9 Watt Lamp Head
1 Single Lighting Head
Upon
failure
of
the
normal
utility
power
the
EMS
unit
is
automatically
W129
Standard 12 volt unit
S2N42
6 Volt – 42 Watts
S2E36
6 Volt – 36 Watts
2 Double Lighting Heads
Optional Ceiling9T-Grid
Mount
Watt Lamp
Head Housing
turned
switching
circuit and
provides
S2N54
6 Volt
– 54 Wattsa minimum of 90
S2E60on by a6solid
Volt – state
60 Watts
3 Three Lighting Heads
W
Wedge Base Tungsten
S2N90
6 Volt
– 90Lumen
Watts output will be
S2E72 of emergency
6 Volt – 72 power
Watts to the
minutes
connected
load.
4 Four Lighting Heads
S2E100
6 Volt – 100 Watts
C
Capsule Halogen
maintained
of the
lamp’sS4N42
rating throughout
the entire duration.
S2E120 at 6100%
Volt – 120
Watts
12 Volt – 42 Watts
S
PAR36 Tungsten
S4N90
12
Volt – 90
Watts
A solid
state
low
voltage
disconnect
circuit
is
used
to
protect
the
battery
H
PAR36 Halogen
S4E36
12 Volt – 36 Watts
S4N130
12 Volt – 130 Watts
23-7/8"
from
being severely
For additional Lampheads
S4E60
12 Volt – damaged
60 Watts by a deep discharge. When normal utility
refer to Lamp Selection
Wattsswitches the load back to normal utility
S4E72
12 Voltthe
– 72unit
power
is restored,
Guide Data sheet RH
S4E120
12
Volt
–
120
Watts
operation and the fully automatic, temperature compensated, dual mode
Note: Total lamp wattage must
S4E140
12 Volt – 140 Watts
charger begins to restore the battery; bringing it to full charge within
not exceed unit 90 minute
capacity rating
UL 924 specified parameters. A brownout sensing circuit insures proper
90 Minute Capacity
2 hrs
Options
1/2" Extrusion from wall
after installation
SD Self Test / Self Diagnostic
V
Voltmeter
A
Ammeter
4-3/4"
TD
15 Minute Time Delay (Specify
AC Voltage)
4"
C
3 ft. Conductor Cord & Plug
MH Metal Lamp Heads PAR 36
(type S & H lamps only)
MR MR16 Lampheads (12 Volt
6-1/4"
only, see lamp selection
guide)
WG6 Wire Guard
operation
during
“low line” conditions.
Example:
S2E36-2-W69-SD
3161 Metropolitan
State Road Drive,
• Bensalem,
PA 19053
19020 USA
USA
2572
Trevose, PA
Tel: (800) 872-0879 • Fax: (215) 244-4208
TEL:
(800)
872
0879
•
FAX:(215)
244
4208
•
www.evenlite.com
www.evenlite.com
TL-S 1/14
Tufflite S 6 & 12EMS
Volt,- Emergency
36-130 WattMicro
MetalPower
Series
Emergency Light
Inverters
FEATURESSpecifications
Suggested
An
with sinusoidal
shall be
supplied
capable of powering•any combination
lighting fixtures,
including
• inverter
Two system
fully adjustable,
topoutput
mounted
Par
36 style
Low voltageof cut-off
prevents
batteryincandescent,
damage and
fluorescent,
induction
and/or
LED
light
sources
without
compatibility
problems.
lighting heads in high impact thermoplastic are
ensures positive charge acceptance following an
The system
shall transfer
in less than
1.0 second
to reliably
back up lighting fixtures without
loss discharge
of illumination and operate any and all connected
supplied
as standard.
Lighting
heads
are available
extended
lightingwith
fixtures
at
full
lumen
output
during
the
complete
90
minute
discharge
cycle.
a variety of lamp types and wattage’s
•
Brownout sensing assures emergency operation
The input voltage shall be the same as the output voltage and shall be single phase 1201277 volts, 60 Hz. Output capacity will be 20 /35 VA with
• Accommodates up to four lighting heads (2 top,
during periods of low line voltage
NiCad Batteries or 32/55 VA with lead Acid Batteries to order for a minimum duration of 90 minutes.
2 side) Standard units are supplied with two top
• Short
battery
protection
The design shall be a standby, off-line inverter with on-line efficiency of 98%; on-line
doublecircuit
conversion
UPS systems
shall not be considered acceptable
mounted heads
alternatives EMS system output shall be a PWM generated sine wave with less than
3%
total
harmonic
distortion.
The
shall also provide short
• ARRA Compliant for Level system
1
• 20
steel
cabinet
universal knock-out
circuit
andgauge
overload
protection
as with
standard.
•
Listed to UL 924, meets NFPA 101 Life Safety Code,
mounting
pattern
in asystem
durable
white powder
An intuitive
three LED
display shall provide
operational
information at a glance
and alert
user toand
any OSHA
malfunction
in system performance.
NFPA
70-NEC
requirements
(other
colorsshall
available
to order)
coat maintenance
Authorized
personnel
have access
to the system’s controls while being protected
• 3 Year limited warranty
from
exposed
connections.
AC Input Connection
• any
Keylivehole
mounting
slots and conduit knockouts are
Protective
devices for
shalladditional
include DC input
fuse, ACpossibilities
input overcurrent protection for live circuits to be
provided
mounting
Operating Characteristics
provided by service panel rated 20A maximum. AC lockout, reverse battery connection, low voltage
• Choice
of maintenance
freeand
sealed
Lead
Calcium
orbe provided standard on all
Wattage
battery
disconnect
(LVD), short circuit
overload
protection
shall
Model
Voltage
Nickel
Cadmium
batteries
90
min
2
hrs
3 hrs
models. The entire EMS system, including batteries, shall be provided in compact cabinetry which shall
have
or (surface)(recessed)(T-Grid)
6
36
27
18
S2E36
• provisions
Premium,
fully automatic currentmounting.
limited “Pulse
S2N42
System shall utilize a (sealed lead calcium battery with a 10 year design life)(sealed Nickel-Cadmium
6
42
31
4 hrs
12
21
15
Switching” charger provides ideal charge conditions
batteryfor
with
a 15 year design
life).
The charger shall
temperature compensated, dual mode
type, and
6
54
36
27
18
S2N54
optimum
battery
performance
andbelife
recharge the batteries as per UL 924 guidelines. Entire system shall be tested, approved, andS2E60
labeled to
6
60
45
30
22
• Self
Test / Self
Diagnostic
available
UL924
Emergency
Lighting
and Powermonitoring
Systems standards.
T-Grid models will be plenum rated.
6
72
54
36
27
S2E72
• External Momentary test switch and dual
6
90
67
45
33
S2N90
Wiring
Diagrams
diagnostic
LED indicator displays AC presence
6
120
90
60
45
S2E120
and Hi-Charge status
12
130
97
65
48
S4N130
NiCad Batteries deliver the same capacity per wattage as above for listed models
• Field selectable 120 or 277 VAC input
6&12 Volt models deliver the same capacity per wattage as above for listed models
• Line-latch prevents unnecessary discharge of battery
during installation, loads will not illuminate until
after application of utility power
ORDERING GUIDE
S2E36
No. of Top Mounted
Lighting Heads
Model
Model
Lead Calcium Battery
90 Minute Capacity
Nickel Cadmium Battery
90 Minute Capacity
S2E36
S2E60
S2E72
S2E100
S2E120
6 Volt – 36 Watts
6 Volt – 60 Watts
6 Volt – 72 Watts
6 Volt – 100 Watts
6 Volt – 120 Watts
S2N42
S2N54
S2N90
6 Volt – 42 Watts
6 Volt – 54 Watts
6 Volt – 90 Watts
S4E36
S4E60
S4E72
S4E120
S4E140
12 Volt – 36 Watts
12 Volt – 60 Watts
12 Volt – 72 Watts
12 Volt – 120 Watts
12 Volt – 140 Watts
S4N42
S4N90
S4N130
12 Volt – 42 Watts
12 Volt – 90 Watts
12 Volt – 130 Watts
0
1
2
3
4
No Lighting Heads
Single Lighting Head
Double Lighting Heads
Three Lighting Heads
Four Lighting Heads
Lighting Heads
Options
W69
SD
V
A
TD
Standard 6 volt unit
9 Watt Lamp Head
W129 Standard 12 volt unit
9 Watt Lamp Head
W
Wedge Base Tungsten
C
Capsule Halogen
S
PAR36 Tungsten
H
PAR36 Halogen
For additional Lampheads
refer to Lamp Selection
Guide Data sheet RH
Note: Total lamp wattage must
not exceed unit 90 minute
capacity rating
Self Test / Self Diagnostic
Voltmeter
Ammeter
15 Minute Time Delay (Specify
AC Voltage)
C
3 ft. Conductor Cord & Plug
MH Metal Lamp Heads PAR 36
(type S & H lamps only)
MR MR16 Lampheads (12 Volt
only, see lamp selection
guide)
WG6 Wire Guard
Example: S2E36-2-W69-SD
3161 Metropolitan
State Road Drive,
• Bensalem,
PA 19053
19020 USA
USA
2572
Trevose, PA
Tel: (800) 872-0879 • Fax: (215) 244-4208
TEL:
(800)
872
0879
•
FAX:(215)
244
4208
•
www.evenlite.com
www.evenlite.com
TL-S 1/14
EMS 10/15